AIR PURIFIER - Sinclair.pl
Contents
1. cover insert component s dust sensor clasp display board screw Operating Procedures Photos 6 Disassemble back cover Unscrew 2 screws on the front side of front panel and 3 screws on the back cover to remove the back cover back cover screw C Disassemble centrifugal fan Unscrew the nut on the centrifugal fan to remove the centrifugal fan electric box cover centrifugal fan nut 2 Disassemble electric box Unscrew a screw on the electric box cover to remove the electric box cover Unscrew the screws fixing mainboard SEN capacity plasma and anion generator and pull out the lecie box motor insert component to remove the mainboard cover capacity plasma and anion generator Operating Procedures Photos mainboard motor insert component plasma and anion generator 2 Disassemble motor Remove the motor wire press plate unscrew the 4 screws fixing motor to remove the motor note Don t lost the gasket on the motor axes motor wire press plate motor 10 Disassemble power cord Unscrew the 4 screws on the chassis to remove the chassis Remove the power cord from groove and pull the insert component out chassis power cord 9 Trouble shooting 9 Please reaffirm the problems before asking for maintenance Symptoms Check Processing method Whether the battery is dead Replace with new battery The remote control does not work Are the positive and neg2. 1 Disassemble front panel Press the both buttons of front opanel open the front panel onwards and lift it upwards to remove the front panel front panel button Disassemble filter subassembly and dust shelf Hold the top handle of filter subassembly and pull it outwards take out the top both clasp then take out the bottom clasp to remove the filter subassembly Hold the twi handles of dust shelf and pull it outwards to remove the dust shelf 3 Disassemble filter subassembly and HIMOP grid Hold the handle of grid and pull it outwards to remove the HIMOP grid The filter subassembiv is on the HIMOP grid and including filter cotton and HIMOP HEPA filter tear the filter cotton handle directly then loose the two clasps of HIMOP HEPA filter to remove the HIMOP HEPA filter HIMOP grid Operating Procedures Photos HIMOP grid HIMOP HEPA clasp filter filter cotton Disassemble active carbon filter Remove the active carbon from grid and replace it Don t disasseble the active carbon grid active carbon grid active carbon filter 5 Disassemble display board Screw Unscrew the 3 screws on the display box cover to removethe display box cover Unscrew the 3 screws fixing display board and loose the two insert components which connect mainboard and dust sensor to remove i AR the display board loose the 2 clasps on the dust sensor to Ma mr remove the dust sensor Li displav box
3. Outline Dimension Outline Dimension iso eo oo oo oo ob 3 3 os so e es e s e v o e e s e oo y 0000 0000 9 6 fieri ee e n GN l Q Unit mm 245 5 Electrical Circuit Diagram gt Model SP 300A Dust MI POWER Sensor L Plasm Negative lon Producer RD FAN MOTOR These circuit diagrams are subject to change without notice please refer to the one supplied with the unit 5 6 Controller Function Manual and Operation Method gt Manual of Controller Function Basic Function Mode e Auto Mode The fan speed can be adjusted automatically under auto mode but if press the FAN key on the remote controller the fan speed can not be adjusted When the auto lamp is light the corresponding fan speed lamp is light When the fan runs with turbo it will runs with turbo mode and turbo lamp is light When the degree of off flavor or dust is low the green lamp is light when
4. SERVICE MANUAL AIR PURIFIER SP 300A DSi SINCLCUR AIR CONDITIONING 1 Summary and Features Main Function Feather Silver ion sterilizing anti mildew x Cold catalyst A HIMOP High efficiency dispel formaldehyde A HEPA High efficiency filtering jk Active carbon adsorb hramful gas high efficient Xx Plasma Xx Anion Quiet design Model SP 300A 2 Technical Specifications 220 240V 50Hz Air Flow 3 Power o s 7 o pew o a a a Product 396 W X 245 D X576 H Product The surface is the surface influenced by which the unit runs under high fan speed The above data is subject to change without notice Please refer to the nameplate of the unit Lo 3 Part Name lt gt Unit Parts Remote control Filter screen Activated carbon HIMOP net rack Host display screen a Button L carbon net rack bodv Filter Components Cotton filter HIMOP HEPA filter components Dust Frame Air inlet Panel Filternetzkomponenten Unit display scree Indicator light Mode button On Off button Clean Change Odor sensor l H e AIR PURIFIER Dust sensor Lock Fan Speed oO O O O O O O O O O O 0 o OO 0 0 0 0 O HEPA Mute Low High Turbo Auto Sleep Anion Odor 1 2 4 Dedust filter AT MOP fe o o o o e e o o e o Oo o O Oo e o lo 88 o vi Remote control T receiver window Dust sensor Odor sensor 4
5. ative poles installed reversely Install the battery correctly Does indoor fluorescent light keep flickering for the reason of lifespan Is the power plugged in Plug the power supply Can not start Is the panel correctly installed I Plug the power supply Keep the machine in a distance from the fluorescent Please contact the after sales There is no air blowing kaa ag t service in this case Is it installed in unventilated areas or are there any obstacles Remove obstacles near the machine Do not achieved the cleaning effect Is there too much dust on the filter components filter cotton Clean the filters and replace and HIMOP HEPA filter filter cotton components Is there t h odor and i A ee ia l Clean activated carbon filters smoke produced Are there any TV radio within 2 Move the TV radio and indoor meters away from the machine antennas more than 2 meters or 18 there any indoor antennas away from the machine near the machine The TV signal is in interference Are there any power cords or Keep the power lines or television television sets radio antenna sets radio antenna as far as which are close to the machine possible away from the machine Is there lots of smell released The smell will be gradually temporarily Many people disappearing when the machine It smells in the air outlet smoke or barbecue runs for some time i W Not Maintain the activated carbon filters cleaned o
6. emove dust in the air and it is easy to use in cleaning the air Timer Timerbutton O If it in power state every time you press the button the timing will change according to the following sequence And the timing light of host computer will flash accordingly then you can you can select the time Mi 1 hour 2 2 hour ii Cancel 4 4 hour Note when it is at power on the timing is for timed shutdown when it at power off the timing is for timed power on Odor button e When it is in running state click the button the machine will be in this mode The plasma opens and the fanwill run at the highest speed a o 4 X You can change the fanspeed through the speed button Anion 3 Anion button e When it is in running state click the button the machine will be in this mode The negative ion opens and the fanwill run at low speed gt lt You can change the fanspeed through the speed button Sleep Sleep button e When it is in running state click the button The machine automatically adjust mute fanspeed or low speed according to air quality X In this mode the speed button is invalid Auto Auto button Vhen it is in running state click the button The machine automatically adjust the on off switch of plasma according to air quality gt lt In this mode the speed button is invalid Electrostatic Electrostatic cleaning e The button is invalid on this machine If it 1
7. ith default fan speed of each mode c When the unit is stand by press mode key for 5S all the indicator lamps are light and buzzer gives out beep the cumulate time is clearance Note When the unit runs 0 5h the time cumulates one time and no cumulation if runs less than 0 5h The corresponding indicator lamp blinks to remind customer clean or replace it when the total cumulate time reaches Before the cumulate time haven t been cleared the indicator blinks if re energized If both cumulate time of clean and replace do not reach they are clearance after resetting used for factory zero clearing if one cumulate time reaches only clear it after resetting the other continues to run if both of them reach clear them after resetting 4 Function of remote control button ON OFF After the unit is first energized press ON OFF when the unit is off it will run with auto mode if turn on the unit again it will run with the previous mode the unit is off if pressing ON OFF when the unit is on Child Lock Press it for 2S the unit runs under this mode it will be cancelled for 2 ways lock function key with remote controller press for 2S or the unit is power fail Six mode keys There are below modes auto turbo sleep anion clear off flavor The button is valid when the unit is on a If the current modes are auto sleep and turbo it will shift to the default status of this mode if pressing anion and anti off flavor If the current mode
8. r replaced for a long time PARTS GUIDE SINCLAIR AIR CONDITIONING 8 Assembly Drawing and Sparepart List Assembly Drawing List Parts List for SP 300A SDA SP 300A 6 ElecticBoxCover 20126083 1 AE 8 WieClam 26116072 1 AB 9 FroniCase 20006065 1 AU 14 Overbad Protector none 0 ____ The data are subject to change without notice
9. s are anion and anti off flavor press the mode key which the same as the current mode the buzzer gives out beep and no action for controller b If the current mode is DUST Enter anion mode if press anion button and default the status operation if press anion mode Enter clear off flavor mode if press off flavor button and default the status operation if press clear off flavor mode There is no change if press dedust button c If the current mode is anion Enter clear off flavor mode if press off flavor button and default the status operation if press clear off flavor mode There is no change if press anion static dedust button d If the current mode is clear off flavor Enter anion mode if press anion button and default the status operation if press anion mode There is no change if press clear off flavor static dedust button Timer Key The unit will choose circularly by timer 1h gt 2h gt 4h gt cancel if press this button Press timer if the unit is off that means set timer on press timer if the unit is on that means set timer off Eg set the current timer to turn off the unit 1h later then repress it is to turn off the unit 2h later and then repress is to turn off the unit 4h later last press it is cancel it Then press it is to turn off the unit 1h later cycle like this Note If the current setting timer is 1h and does not reach presses TIMER the timer time will update to2h and restart to time regarding 2h If the unit i
10. s not in use for a long term 1 Please switch off unplug the power plug and tie up power cord 2 Clean each filter part air inlet outlet and the host body 3 Place the carbon filter in a suitable plastic bag seal it and put it in the machine 4 Cover it with dust cover and place it in a shade and well ventilated place Replace Battery 1 Open the back cover of the remote control according to the arrow direction 2 Replace it with CR2025 battery and the close the lid Note e The battery should be placed where children can not reach If a child accidentally swallow the battery you should quickly get in touch with the doctor Before the battery is discarded please use the tape etc wrap it at both ends of positive and negative poles to prevent mixing with other metals or batteries and causing fever rupture fire and so on e When the battery is not used any longer please put it into battery recycling place at the nearest electrical shop watch or camera stores e The criteria for replacing battery is 1 year However if it is not found insensitive in receiving signals please replace the battery e Please replace the battery as soon as possible when it is close to the battery lifespan In order to avoid the failure and injury caused by fluid leakage or rupture please remove the battery if it is not in use for a long time Disassembly Procedures Disassembly Process Operating Procedures Photos
11. s on and is set timer time off already receiving the signal to turn off the unit the unit is off and clears timer information If the unit is off and is set timer time on already receiving the signal to turn on the unit the unit is on and clears timer information e Fan Key It cycles by quiet gt low speed gt high speed It is invalid with stand by auto sleep and turbo mode The fan speed runs with initial fan speed of each model when shift mode by remote control Setting Key The brightness of indicator lamp will be adjusted per press the dust induction lamp and off flavor induction lamp will display circularly by bright gt dark gt go out and other lamps will display circularly by bright gt dark gt dark gt bright Names and Functions of Remote Control Buttons The perfect functional regulation need to be completed by remote control Remote control On Off On Off button Click the button when it is in standby mode and the machine will begin to run If you press it again the machine will stop running pou Speed button e When it is in running state fanspeed will switch according to the following sequence And the speed light of host computer will flash then you can select the fan speed pi High gt Low Mute a Turbo Turbo button e When it is in running state click the button and the machine will be in this mode Plasma opens and the fanruns in ultra high speed X High air flow can quickly r
12. t under sleep mode the anion lamp is light under anion mode the anti off flavor is light under anti off flavor e Fan speed Lamp When the high med low lamp are light that means the fan runs with high med low fan speed Timer Lamp When the timer 1 2 4 lamp are light that means the timer time is 1h 2h 4h respectively when the unit is on the lamp is light shows setting timer is off when the unit is off the lamp is light shows setting timer is on and there is no timer when the light is dark Clear Replace Lamp When the clear lamp is blinking that means the unit runs 480h totally and remind to clean filter The lamp is dark when the conditions are not satisfied or resetting after clean When the clear lamp is blinking that means the unit runs 2000h totally and remind to replace HEPA HIMOP filter The lamp is dark when the conditions are not satisfied or resetting after clean Child Lock Dust Induction Off flavor Induction Controlled by remote controller 3 Functions of front panel button There are ON OFF button and MODE button on the front panel a After the unit is first energized press ON OFF when the unit is off it will run with auto mode if turn on the unit again it will run with the previous mode the unit is off if pressing ON OFF when the unit is on b Press MODE when the unit is on it will choose circularly by auto gt turbo gt sleep gt anion gt clear off flavor gt auto and the fan speed runs w
13. the degree of off flavor or dust is med the green lamp and orange lamp are light when the degree of off flavor or dust is high the green lamp orange lamp and red lamp are light e Turbo Mode When the plasma is open and anion is close the fan speed defaults turbo running the turbo indicator lamp is light the fan speed can not be adjusted if press remote controller Sleep Mode The fan speed can be adjusted automatically low and quiet will change circularly according to the air quality the fan speed can not be adjusted if press remote controller the sleep indicator lamp is light The time is clearance when the unit is off or shift mode Anion Mode When the anion is open and plasma is close the fan speed defaults low running the anion indicator lamp is light the high low and quiet can change circularly if pressing FAN key Clear off flavor Mode When the plasma is open and anion is close the fan speed defaults high running the clear off flavor indicator lamp is light the high low and quiet can change circularly if pressing FAN key 2 The display function of indicator lam may p Indicator light Mode button On Off button e AIR PURIFIER e S ock an Spee unning mode imer Clean Change Odor sensor 1 o_o o_o O O O O Remote control receiver window Dust sensor Odor sensor Operation Mode Lamp The auto lamp is light under auto mode the turbo lamp is light under turbo mode the sleep lamp is ligh
Download Pdf Manuals
Related Search