HP® LASERJET P1505
Contents
1. artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 8 Coat the new cleaned wiper blade with your preferred 9 Install the cleaned PCR Place a small amount of conductive lubricant Install the wiper blade and two screws grease on to the black holder side of the shaft Just a small amount of grease is more than sufficient 10 Place another small amount of conductive grease on to the metal drum axle uniNnet www Uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS DRUM GEAR CHANGE UPDATE If you are replacing the drum the gears will need to be changed over from the OEM to the new There are two methods of removing the gears from OPC drums The first and easiest method is to place the drum in a metal vice2. HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP LASERJET P1505 SERIES TONER CARTRIDGE uniNnet www Uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS REMANUFACTURING THE HP LASERJET P1505 SERIES TONER CARTRIDGE CB436A By Mike Josiah and the Technical Staff at UniNet UPDATED MARCH 2012 In November 2007 Hewlett Packard released the LaserJet P1505 printer The HP P1505 series of laser printers are based on a 17 ppm true 600 dpi Canon engine These cartridges use a chip that controls the toner low functions The CB436A is rated for 2 000 pages Physically the cartridges look like a small 12A 1012 cartridge but there are many differences The printer itself has a very small foot print It s a nice small office home machine The first page out is stated to be in under 8 5 seconds from a power save mode The memory is fixed and not expandable at 8 MB The recommended monthly volume is from 250 1500 pages per month but the maximum monthly duty cycle is 5 000 pages Unlike many small printers these machine
3. RING INSTRUCTIONS 13 Remove the gears from the hopper as shown Leave the large auger gear in place 14 Remove the single screw and end from the opposite side UniNet www uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 15 Remove the magnetic roller assembly Be careful of the bushings They are very fragile To Yen 16 Remove the doctor blade and two screws 17 Clean out all the remaining toner from the hopper Make sure the magnetic roller seals and the doctor blade seals are all clean UniNet www uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 18 Fill the hopper with 100g new replacement toner f
4. approximately two inches back from the gear and slowly tighten the vice The gear should pop out easily This is the only method you can use on the OPC drums which have a weighted slug in the center If you use this method go on to Step 3 The other method is as follows REQUIRED TOOLS AND MATERIALS 1 A 1 4 x 15 metal rod 2 A 1 x 15 wooden dowel 3 A tube of super glue 4 A small piece of emery cloth or sand paper Step 1 Removing the drive gear The drive gear is the gear that has no metal electrical contacts in it These gears are usually larger than the contact gear A Carefully insert the 1 4 metal rod into the center of the gear that has the contacts or the contact gear B Angle the rod so that the rod presses against the edge of the opposite gear The rod should be touching both the inside of the OPC Drum and the edge of the gear C Tap the end of the rod with a hammer working the rod around the entire edge of the gear until the gear comes loose NOTE Gently heating the ends of the drum with a hair dryer or heat gun on low may cause the glue to soften and ease in the removal process Just be careful not to use too much heat and melt the gear Step 2 Removing the contact gear A Insert the 1 wooden Dowel into the gearless end of the drum B Tap the dowel with a hammer until the gear comes loose Step 3 Removing any adhesive from the gears straightening out any damage done to the contact gears metal contact
5. cle SUPPLIES REQUIRED 1 100g replacement toner for use in HP P1505 unique to this series 2 New replacement drum unique to this series 3 Replacement wiper blade unique to this series 4 Replacement doctor blade unique to this series 5 Replacement magnetic roller unique to this series 6 Sealing strip unique to this series T Cotton swabs 8 Isopropyl alcohol 9 Drum padding powder 10 Conductive grease TOOLS REQUIRED 1 Phillips head screwdriver 2 Small common screwdriver 3 Needle nose pliers 4 Jeweler s screwdriver set uniNet www Uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 1 With the handle facing you remove the right side screw and end cap from the cartridge Be careful of the drum cover spring Remove it with the end cap 2 With a pair of needle nose pliers release both the hopper tension springs UniNet www uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to
6. lights Information on the lights is very poor Even the service manual is terrible Top light blinking Cartridge door open no print cartridge installed or there is a paper jam Both lights on Fatal error turn the printer off and unplug it for 30 minutes If the error still exists the printer has a major problem There is no information yet on what these problems may be the service manual has not been released yet Both lights blinking A printer initialization is in progress UniNet www uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com
7. nd screws 25 Place the drum waste hopper into the toner hopper Slide it over so the round hinge pins fit into their respective holes www Uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS i yy ee 5 26 Set the hopper tension springs back in place 2 With the drum cover spring as shown on the end cap install the end cap Lift up the tail of the spring to fit onto the hopper www Uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS it le e eee area z E d or a 28 Lift up the drum cover spring tail to fit as shown on the drum cover Install the screw into the cover 29 Replace the chi
8. or use in HP P1505 19 When a seal becomes available remove the seal port plug and install the seal Bring the tail out through the seal port hole Install the plug UniNet www uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 20 Install the left side end cap and screw Make sure the small contact piece is installed correctly on the end cap 21 Install the doctor blade and two screws 22 Install the magnetic roller black bushing side first Turn the roller until the keyed end locks in place UniNet www uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 23 Install the gears as shown 24 Install the end cap a
9. p UniNet www uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS REPETITIVE DEFECT CHART OPC drum 75 mm Magnetic roller 31 mm PCR 27 mm RUNNING TEST PAGES 1 Test pages must be run from the P1505 MENU 2 Access the PRINTER PREFERENCES MENU then SERVICES and INFORMATION pages 3 There are three test pages that can be selected The DEMO CONFIG and SUPPLY STATUS PAGE RUNNING THE CLEANING PAGE 1 The cleaning page for these machines can only be run from the PRINTER MENU HP recommends that a transparency be used for best results If a transparency is not available user copier grade paper with a smooth surface 2 Access the PRINTER PREFERENCES 3 Click on DEVICE SETTINGS Press START The cleaning cycle takes up to two full minutes 4 The page will start and stop Do not turn the printer off until the cleaning page has finished printing PRINTER TROUBLESHOOTING As with all low cost machines these days this series of these machines do not have a display panel All the error codes consist of different pattern of the two
10. rtwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS NOTE Be very careful not to place the metal contacts in direct contact with the glue as this will interfere with the proper grounding of the drum and the cartridge will not print properly Solid black pages It is also very important to NOT put any glue on the gear as the chances of it dripping out onto the drum surface and ruining it are high Placing the glue inside the drum tube works much better 11 Install the new cleaned drum hub side first Place the waste drum section aside 12 On the toner supply chamber right side remove the two screws and end cap Note that these screws have lock washers uniNnet www Uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTU
11. s A Removing the adhesive can be done with a small sharp common screwdriver The glue comes off easily Step 4 Install the gears on the new replacement drum A Inspect the metal contacts on the contact gear Make sure that the contacts will make proper contact with the inside of the OPC drum B Locate the side of the drum on which you are going to place the contact gear On some OPC drums this is critical See individual instructions for more information C Lightly sand the INSIDE of the OPC where the metal parts of the contact gear will meet This will insure a good electrical contact D Dry fit the contact gear in the OPC drum and check for a good contact with an Ohmmeter The reading should be a direct short or no more than 1 or 2 Ohms NOTE When checking the contact place one lead on the drum axle contact and the other on the edge of the drum This way you will not have to pierce the coating that is on the OPC surface Radio Shack carries cheap Ohmmeters for less than 10 00 USD and the sales people will normally be glad to show you how to use it E Using the super glue place a few 3 4 small drops of glue strategically around the inside edge of the OPC drum Make sure you leave a blank area for the metal contacts F Insert the contact gear G Check for continuity again with the Ohmmeter H Repeat steps E and F for the drive gear UniNet www uninetimaging com 2012 UniNet Imaging Inc All trademark names and a
12. s have an input tray that can hold 150 pages A nice touch The system that holds the two halves of the cartridge together is completely new The good news here is that you don t have to cut holes in the cartridge to get access to the pins The toner inside is also new HP is stating that the toner now has spherically shaped particles We are currently investigating if this means the toner is chemical or conventional toner that has been thermally rounded Our guess is that it is thermally rounded toner but until our investigations are finished we won t know for sure In addition to the new toner the chips also have intelligence added to help aid in cartridge ordering when supplies are low Again we are investigating the chips for these cartridges at the time of this writing We can say that we have run the same cartridge now five times and the chip has not shut the printer down Just the toner low features are not working The printer when new comes with a starter cartridge that is rated for 700 pages at 5 coverage so your customers will be coming to you fairly quickly So far there are four printers based on this engine the P1000 P1006 P1007 and P1008 At the time of this writing only the P1006 has been released The other models are referred to in the service manual Cartridge troubleshooting as well as running test pages cleaning pages and some simple printer troubleshooting will be covered at the end of this arti
13. show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS 3 Slide the waste drum section over to the left side Separate the two halves 4 On the waste drum section lift the drum up from the gear 5 Remove the PCR and clean with your standard PCR cleaner side Twist and remove from the hopper uniNet www Uninetimaging com 2012 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1505 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS ia ana m E ae s w peie 1 6 Remove the two screws and the wiper blade T Clean out all the waste toner from the hopper Be careful not to damage the recovery blade located next to the wiper blade If this blade is bent in any way the cartridge will leak Make sure the wiper blade foam seals are clean UniNet www uninetimaging com 2012 UniNet Imaging Inc All trademark names and
Download Pdf Manuals
Related Search