FoCOM user manual - Auto
Contents
1. FoCOM drivers are automatically updated during the FoCOM installation When prompted to install unsigned drivers click on nstall this driver software anyway Microsoft Windows 7 or Continue Anyway Microsoft Windows XP A The software you are installing for this hardware Kl Windows can t verify the publisher of this driver software gt Don t install this driver software You should check your manufacturer s website for updated driver software for your device gt Install this driver software anyway Only install driver software obtained from your manufacturer s website or disc Unsigned software from other sources may harm your computer or steal information v See details ELM USB Interface has not passed Windows Logo testing to verify its compatibility sting is i t with Windows XP T why this testi Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing STOP Installation Microsoft Windows will automatically install drivers when you plug in the FoCOM to USB port Driver installation isn t required for operation on GNU Linux system my 3 FoCOM user manual S E CON S www obdtester com focom 2 2 Microsoft Windows 8 driver ins2. 6 5 PATS Immobilizer Passive Anti Theft System PATS is vehicle immobilizer used in Ford vehicles since 1998 PATS functionality is present in PCM IPC BCM or separated PATS ECU according PATS version Ford uses Texas Instruments or Texas Instruments Crypto transponders vehicles since 2001 Several generations of PATS are used Operations with PATS are authorized by timing access delay before operation is allowed so called Timed PATS or by entering INCODE Coded PATS For coded PATS ECU generates OUTCODE for which you need to enter correct INCODE INCODE depends on OUTCODE OUTCODE and consequently INCODE are time dependent these are not fixed codes INCODE authorization service is available on www patscode com or you can use Ford ETIS 6 6 Diagnostics of TCM and ICU Automatic Transmission Control Unit TCM can be diagnosed via PCM Injector Control Unit is always diagnosed from PCM 17 43 FoCOM user manual S E CON S www obdtester com focom 7 Auto scan This function scans for all known ECUs in selected vehicle and shows the list of ECUs present in vehicle along with number of present or stored fault codes DCTs Autoscan may take a while for high end models with many control units EFoCOM Diagnostic program for Ford Mazda ee es FoCOM zYcom Auto Scan Results Auto Scan Results Control Unit DTC Count lt PCM Powertrain Control Module Engine ECU amp TCM Transmission Co
3. Control Unit Diagnostics also known as live data or sensor values is simultaneously Measured parameters can be chosen from selectors at the top of the window Buttons and allow to accelerate or decelerate speed of the graph SECONS E FoCOM Diagnostic program for Ford Mazda Claas Measured Values 3x3 View RCM Bosch CR16 CA 2000 Ford Ka 9 6 2 Display 3x3 com Measured Values 3x3 View Control Unit For measuring 9 value simultaneously click on 3x3 View button ic lalfunction Indicator Lamp Active il O00mode SECONS S 9 6 3 Display list aco aE TENT 1o gu ES fco Cer ctae ca 2000 Fard Ka To measure all available values mme Battery Positive Voltage 8 870 V simultaneously click List view button Aue Deni cce reet Er Diagnostic Trouble Codes 0 000 nmb Please note values means slower refresh rate Driver Airbag 0 000 Ohms Driver Retractor Circuit Resistance A D Count 0 000 Ohms Malfunction Indicator Lamp Active Passenger Airbag 0 000 Ohms Passenger Retractor Circuit Resistance 0 000 Ohms Side Airbag Configuration Inactive State of ECU 1 000 nmb State of ECU 1 000 mode State of ECU 1 000 mode SeCons SEN Please note that refresh rate of live data in list view depends on communication speed SCP and ISO ECUs may return data very slowly 9 6 4 Save to log Measured values can be saved logged to a file by clicking Start logging button The log file is sta
4. Ford DCL Bus l 3 11 Ford DCL Bus Chassis ground GND 4 12 Signal ground GND 5 13 l6 l 14 ISO9141 K Line i7 15 IS09141 L Line Is 16 This connector is used only for diagnostic of older vehicles by DLC protocol connector is compatible with OBD II connector OBD II 9 10 SAE 71850 Bus 11 MS CAN Low 12 In SAE J1850Bus 7 MS CAN High 3 Chassis ground GND 4 5 6 7 Signal ground GND HS CAN High 14 HS CAN Low ISO9141 K Line 15 ISO9141 L Line Is 16 Diagnostic connector is mandatory in all vehicles after 2000 is used from 1996 13 Flash Pom Volt 12 43 FoCOM user manual S E CON S www obdtester com focom 5 Settings All functions in settings are described below F Ci o N A D 3 ti forF 1 A A 4 FoCOM zYcom Application Settings plication Language Units type 4 Protocol settings Main menu KZ awe Protocol init idle time Initialization timeout Expert Functions C Keyword delay Expert Mode Ill Development functions c Delay after init Inter byte delay Interface port selection Inter byte timeout Idle packet delay Seen Test Interface Inter packet timeout FoCOMap 0 1 2241 Timer FOCOM Debug Functions Debug mode mn SECONS Lang
5. SeCons Lest e KS 33 43 FoCOM user manual S E CON S www obdtester com focom 9 13 ECU Programmable parameters Configuration This function allows you to configure control unit parameters or transfer configuration between ECUs after replacement It is possible to reconfigure control unit s multiple times thus allowing to re use control units You can see listing of supported codings for each ECU in our FoCOM diagnostics coverage please note that actual number of configurable parameters may VADE due to different ECU variants FoCOM Diagnostic program for Ford Mazda e k COM IPC Visteon 2004 2008 Ford Focus Icom Control Unit Configuration Control Unit ABS Absent SE r Absent Unit Additional fuel heater Absent iagnostics Control Uni Cruise control Present on EHPAS Present Main menu Electric parking brake Present Focus ST speedometer Present Instant fuel Absent Language Spanish Navigation Absent Real engine temperature Disabled rm Li J SECONS m Always save backup of configuration to a file before making any changes If no editable values are displayed it is still possible to save or restore configuration via a file If complete configuration load fails for any reason it is still possible to continue with ECU A configuration data subset The configuration data retrieved from the control unit are verified for validity after loading First check is performed to validate
6. amp TBCM Traction Battery Control Module BACM Battery Control Module SECONS 6 1 Diagnostics of selected non standard models Ford Galaxy I 1995 2000 Both generations were manufactured as a joint venture Ford Galaxy II 2000 2006 product between Ford and VW based on VW Sharan y platform Please use Special diagnostics VW Ford Galaxy Diagnostics 2 31 EEC V PCM and PATS uses standard protocol Ford Galaxy after 2006 is based on Ford CD340 platform and uses standard Ford diagnostics Ford Galaxy III 2006 present Can be diagnosed by FoCOM 1n standard way Ford Ka I 1996 2008 Can be diagnosed by FoCOM in standard way Ford Ka II 2008 present You need use Fiat Examiner or FiCOM or to diagnose them This vehicle is manufactured as a joint venture product between Ford and Fiat Land Rover Freelander 97 06 You need use BMW diagnostic tool such as BimCOM Land Rover Range Rover 94 05 You need use BMW diagnostic tool such as BimCOM Volvo all models Please use Special diagnostics Volvo diagnostics To diagnose EEC IV control units 1988 1996 Ford Escort up to 1999 use Special Diagnostics EEC IV DCL 15 43 m vn FoCOM user manual S E ON S www obdtester com focom 6 2 Communication protocols Protocol Bus Production DCL CART DCL RS485 1988 1996 Ford SCP SAE J1850 PWM 1996 2005 Ford ISO ISO9141 1996
7. fault code stored in ECU memory Fault codes might appear again or under some conditions isn t possible to clear fault codes at all It s possible that in the presence of some faults control unit doesn t allow to clear fault codes or fault is in no time written back to memory It is recommended to read memory by clicking Re read fault codes button again D Please note that number of clearing fault codes may be limited for some control unit types 24 43 FoCOM user manual S E CON S www obdtester com focom 9 5 Freeze frame Freeze frame displays conditions at first or last occurrence of currently selected fault code 2 5 EEC V MLF 521 2000 Ford Cougar Cou Freeze Frame Freeze Frame Fault Code Memory B Raw Freeze Frame Data 02 01 93 agg Raw Freeze Frame Data 03 01 00 Gta Raw Freeze Frame Data 04 00 tm Raw Freeze Frame Data 05 00 DEE Raw Freeze Frame Data 06 FF Raw Freeze Frame Data 07 80 Raw Freeze Frame Data 08 FF Raw Freeze Frame Data 09 80 Raw Freeze Frame Data DC 00 00 Raw Freeze Frame Data OD 00 SECONS 25 43 FoCOM user manual S E CON S www obdtester com focom 9 6 Measured values live data Some control units are not equipped with all sensors in this case some sensors may show a limit values minimum or maximum FoCOM Diagnostic program for Ford Mazda Lol ks 9 6 1 Graph display Zcom RCM Bosch CR16 CA 2000 Ford Ka Measured Values Graph View This function displays two measured values o
8. focom 2 3 Interface busy issue Microsoft Windows In case you receive error Interface busy while testing your interface please make sure 1 You re not running any modem mobile phone or printer monitoring application that blocks COM ports from being used by other applications 2 You re not running Hella Gutmann software on the same PC Process called GMPortal exe prevents SECONS diagnostic applications from properly accessing the diagnostic interface You may temporarily resolve this problem by running Windows Task Manager right clicking on GMPortal exe process in Processes tab and selecting End process Software modem drivers do not block COM ports 4 You have selected correct COM port use Device manager button to find port number under Ports COM amp LPT group 2 4 GNU Linux System Our diagnostic application are tested to work under Linux The applications can be run under Linux BSD or Apple OS X on Intel x86 using Wine environment The installer and applications perform fully automated installation under these operating system 2 4 1 Requirements Linux 2 6 x with USB support or FreeBSD USB CDC Driver Wine 1 0 1 Recent Debian Linux or Ubuntu meet the above requirements 2 4 2 Setting up devices Driver installation isn t required for operation on GNU Linux system Diagnostic applications require access to dev ttyACMx devices from Wine environment This can be set up
9. refer to technical service bulletins and workshop service manuals before running any of these functions Diagnostic program for Ford Mazd FoCOM zz CoM Application Settings Application Settings r 77 K Protocol settings EN g Main menu Protocol init idle time Initialization timeout Keyword delay Expert Functions _ _ _E _ _ _ em IE Expert Mode Ill Development functions Delay after init Inter byte delay Interface port selection Inter byte timeout cowus f Inter packet delay Idle packet delay Inter packet timeout Timer FOCOM Sesser Debug Functions Debug mode SECONS 20 43 FoCOM user manual S E CON S www obdtester com focom 9 1 Unrecognized Control Unit Some Ford control units may do not return unique identification or FoCOM may not correctly identify them In such case is it necessary to choose correct type of the control unit from list n 3 FoCOM Diagnostic program for Ford Mazd Le m PCM Powertrain Control Module Engine ECU Invalid iden Lion Unrecognized Control Unit Dg poi sing No valid identification was returned from ECU Application thus cannot identify Control Unit ECU You can either use generic ECU mode by clicking on Use Generic Selection Access button or select correct control unit from the list below Please note that Main menu you can DAMAGE the control unit and or oth
10. 2008 ISO 15765 CAN BUS ISO 11898 2003 present UDS ISO 14229 CAN BUS ISO 11898 2008 present 6 3 Information about Ford control units Every vehicle after 1996 contains at least one ECUs Electronic Control Unit powertrain control unit PCM is present every time in modern types also ABS RCM Airbag perhaps even IPC Instrument Panel Cluster BCM Body Control Module and many others Important notice for Jaguar diagnosis due to differences and incompatibility between addressing schemes used Jaguar and other Ford Motor Company vehicles some Jaguar ECUs may have different function Ford Motor Company ECU Jaguar ECU RPSDM Rear passenger sliding door module Heater module Webasto heater ILCM Illuminated Light Control Module Tire Pressure Monitor SASM Steering angle sensor module Passenger Seat Module 6 4 Ford ECU terminology PCM Powertrain Control Module ICU Injector Control Unit TCM Transmission Control Module EPS Electronic Power Steering IPC Instrument Panel Cluster HEC Hybrid Electric Cluster same as IPC RCM Restraint Control Module airbags etc ECS Restraint Control Module same as RCM BCM Body Control Module 16 43 m vn FoCOM user manual S E CON S www obdtester com focom GEM General Electric Module PATS Immobilizer Passive Anti Theft System also part of PCM BCM IPC RKE RKE Remote Keyless Entry
11. DTC reading Fault code clearing Measured values live data Live data recording Diagnostic protocol printing e Actuator tests Commands Coding Configuration Programmable parameters in dealer tool The FoCOM system works with Ford vehicles It works as well with Ford subsidiaries vehicles such as Mazda Lincoln Mercury Jaguar but without guarantee of 10096 functionality The rule of thumb is tasks related to fault code memory and identification are reliable everywhere but measured values and other functions may not be fully supported 5 43 SECONS FoCOM user manual www obdtester com focom 2 FoCOM software and driver installation 2 1 Microsoft Windows operating System 1 Insert FoCOM installation CD to your CD ROM drive 2 Run installation file FoComSetup exe 3 Choose language for the installer Installer Language 27 Please select the language of the installer English iv 4 Choose your destination folder for the FoCOM and click on nstall button and after successful installation click on C ose button Ke SECONS FoCom Ford Diagnostic Tool Setup Installation Folder m Setup will install SECONS FoCom Ford Diagnostic Tool in the following folder To install in a different folder click Browse and select another folder i Click Install to start the installation Destination Folder C Program Files FoCom Space required 971 0KB Space available 16 1GB
12. Direct Flash EEPROM programming functions are described in separate document and require additional license 11 7 Autoscan Network test This function scans for all known ECUs and shows the list of ECUs present in vehicle along with number of diagnostic trouble codes thus provide test of network Both functions Network Test IDS and Autoscan FoCOM are identical FRAFeCOM Diagnostic program for Ford Mazda be Ses FoCOM cox Auto Scan Results Auto Scan Results Main menu ez PCM Powertrain Control Module Engine ECU TCM Transmission Control Module lt FACM Fuel Additive Control Module lt gt 4x4 Four Wheel Drive All Terrain Control Module Secondary Powertrain Control Module Traction Battery Control Module Battery Control Module Battery Energy Control Module FICM Fuel Injector Control Module lt gt GSM Gear Shift Module SECoNs 40 43 FoCOM user manual S E CON S www obdtester com focom 12 Reporting bugs and improvement requests Our customers can take advantage of our full technical support for free You can contact our technical support at support secons com with any technical questions and requests In case you encounter to failure of any program functions e g fault codes reading clearing coding functions actuator test connecting to ECU test interface or you miss some function or some function does not work sufficiently please follow the steps
13. EECV x Recovery procedure EECVI To diagnose PSG5 VP44 Bosch TTDi fuel pump DEE pleas use direct connection to the control unit using universal 3 lead K 12V GND adapter High Speed CAN BUS Analysis Mid Speed CAN BUS Analysis SCP BUS Analysis these functions are described in our manual CAN BUS analysis information available at obdtester com downloads Recovery procedure EECV VT this function is used to recover control units after wrongly performed flash programming 19 43 FoCOM user manual SE CON S www obdtester com focom 9 Diagnostic functions You can connect to ECU by choosing control unit from list of ECUs in selected vehicle or auto scan listing If control unit was identified uniquely diagnostic menu will be available immediately otherwise it is necessary to select control unit variant as described earlier in this manual Diagnostic menu is divided into three parts Basic functions Advanced functions and Expert functions Basic functions generally safe to use under any conditions Please note that clearing deleting fault code memory may result in additional fault codes appearance even in different control unit s Also messages may appear on on board computer display Advanced functions require deeper knowledge of car components Be careful before activating any actuators incorrect actuation may damage vehicle components Expert functions may have serious consequences if used improperly Please
14. FoCOM User manual COM www obdtester com focom FXFSCOM Diagnostic program for Ford Mazda FoCOM con Main menu o FoCOM Diagnostic program for Ford Mazda SEN Lola COM FoCOM Vehicle Diagnostics EAE lt z com Control Unit Selection i Ve pn Les seen nae aiit amp PCM Powertrain Control Module Et www secons com www obdtester com focom lt PCM Powertrain Control Module Er TCM Transmission Control Module TCM Transmission Control Module Mecctieiecum Rcg FACM Fuel Additive Control Module Wo ses amp 4x4 Four Wheel Drive ATOM All Terrain Control Module SPCM Secondary Powertrain Contrc lt TBCM Traction Battery Control Moc SECONS amp BACM Battery Control Module SECONS Driver Retractor Circuit Resistance A D Count 9 043V Main menu State of ECU State of ECU SECONS Copyright 2004 2015 SECONS s r o http www secons com All rights reserved Version 2015 11 24 ke eg Diagnostic Trouble Codes 8 87 0 V Control Unit Diagnostic Trouble Codes Selection Driver Airbag SECONS m 3 FoCOM user manual S E CON S www obdtester com focom SECONS s r o is not connected with Ford Motor Company in any way Please read carefully this user manual before using the FoCOM application Before using the software please read license agreement Ford Lincoln Mercury are registered trademarks of Ford Motor C
15. below Note Before sending support request for failing operation please make sure you have met all conditions required for the operation e g you are entering correct data correct engine temperature for DPF regeneration correct number of keys for engine start etc In case of communication issues we recommend to check diagnostic plug connection and retry procedure at least once connection problems may result in erratic communication issues Please prepare the following data in your email before sending your request to our technical support 1 Detailed description of failure or your improvement request Vehicle description VIN code model manufacture year engine type 3 Attach Debug Log in case that required function doesn t work properly This file captures data from the latest communication between program and ECU so we can detect failure causes 4 Attach Snapshot of tested ECU this file contains important information about tested control unit In all cases please attach snapshot of INJ engine BSI body computer eg 12 1 How to create Debug Log It is necessary to perform operation that is not Promesse Gees working correctly first Once failure occurs go back BON enzege directly to settings in main menu do not close the 2 E program Click on Save Debug button Name and save the file into well known directory in your computer Enable Debug mode check box only at our special request T
16. data consistency such as data check sum If data consistency validation fails prompt if you really want to continue is displayed This usually happens only when control unit is not yet programmed or data are corrupt The diagnostic application is able to fix this problem when writing new configuration to the control unit It is possible to continue however 34 43 m Y FoCOM user manual S E C ON S www obdtester com focom writing incorrect data to the control unit may damage either control unit or vehicle components Then all data are checked for validity If invalid configuration option is found warning message is displayed The window displays all user changeable values Meaning of colors Grey line Read only value cannot be changed Black line Editable text original state not yet edited Green value Editable changed by user Red Un decoded value Violet pink value Un decoded changed value 9 13 1 Edit This button allows you to change currently selected value Detailed instructions on valid value format and it s range is displayed After editing please check displayed value is correct as it may change diagnostic application may adjust the value to meet the control unit requirements the value may get rounded clipped etc 9 13 2 Hex edit Available only in expert mode or for values that cannot be correctly decoded This function is used to directly edit binary representation of the val
17. ect self learnt values present in keep alive memory KAM 9 7 2 Key On Engine Running test KOER test KOER is automated powertrain module test available on most EEC V and EEC VI control units The test must be performed running engine The KOER test may require special actions such as turning steering wheel from minimum to maximum or pressing brake For vehicle specific instructions please refer to Ford service manuals All problems that were detected during the test are displayed in form of fault codes at the end of test The test terminates automatically The KOER test may affect self learnt values present in keep alive memory KAM 27 43 FoCOM user manual S E CON S www obdtester com focom 9 8 Programming Coding functions This function allow you to e g programming VIN code operate with immobilizer PATS or programming calibration data of injectors Important notice Some of the coding functions can not be run when the engine is running and vice versa some coding functions can not be run unless the engine is running Some coding operations require specific conditions or procedure to be performed Please refer to vehicle manufacturer technical service manuals for more information BCM 2010 Ford C MAX COM ECU Programming Coding Programming Co Control Unit Diagnostics 47 PATS state information Main menu lt Program new key 2 PATS coded login Erase all keys and program new lt PATS ECU Pairing lt Batter
18. er parts if you select incorrect ECU and perform actuator tests or programming coding functions Generic access mode is safe 1 4 TDCi Fusion 2003 SID 804 1 4 TDCi Fusion 2007 SID 804 1 4TDCI PCM Ford Fiesta 1 4i PCM Ford Fiesta 1 4i PCM Ford Fusion Use selected ECU gt gt In this situation you can also use generic ECU mode by clicking on Use generic access button however this mode will not allow you to read measured values You can get more information about ECU by clicking on Show ECU Identification button Some ECUs especially those before 2003 don t contain identification data therefore Unrecognized Control Unit information will always appear You should choose correct ECU for correct decoding of measured values A Ifyou make mistake in identification you shouldn t make any programming functions Function Save ECU Information makes possible to save all development information about ECU to hard disc In case that the installed ECU is not available in the listing 21 43 m 3 FoCOM user manual S E CON S www obdtester com focom or you are not sure which control unit to choose or you wish to get the ECU automatically properly identified in next FoCOM version or you just want to help us to improve FOCOM We will be more than happy to add support for any unsupported or unrecognized control unit to next FoCOM version We are usually able to do this within one
19. hese data of configuration doesn t contain coding of injectors function traveled T distance or informations about immobilizer and other Is necessary to perform adaptation of these data using coding operation Display of data from the Ford Motor AS BUILT database includes data for all controls PCM Module BCE Modules PCM 1 FFFF FFFF 0310 7A6 01 01 0900 20B0 20A8 PCM 2 2COC 44FF FE8B 7A6 01 02 00B0 PCM 3 FFFF O3FF 2F42 7A6 02 01 02B2 PCM 4 FFFF FFFF FFOE 720 01 01 6A20 3930 A8C4 PCM 5 FFFF FFFF FF10 720 01 02 0100 2B PCM 6 FFFF FFFF FF11 726 01 01 DAOA 93 PCM 7 FFFF FFFF FF12 726 02 01 OSCO 2222 097 PCM 8 FFFF FFFF FF13 726 03 01 3000 61 PCM 9 FFFF FFFF FF14 726 04 01 OE40 726 05 01 040F 46 726 06 01 0000 34 726 07 01 205 BF 726 08 01 0101 023A 726 09 01 2100 08577 726 10 01 8008 0000 00c6 726 10 02 0000 0000 003F 726 10 03 0000 0000 0040 726 10 04 0000 41 726 11 01 1400 53 32 43 FoCOM user manual S E CON S www obdtester com focom AS BUILT data adjustment entry in FoCOM only for currently diagnosed control unit IPC Visteon 2008 Ford Focus COM Control Unit Configuration a 720 01 01 0000 29 Suecia 720 02 01 5454 3453 54AD Control Un 720 02 02 3045 3453 547B Control Unt 720 02 03 3453 4534 507C ER 720 03 01 0000 2B Main menu 720 04 01 5434 5353 459F 720 04 02 4434 5354 3480 720 04 03 5345 34FA 720 05 01 4535 4354 3472 720 05 02 5345 3453 4592 720 05 03 3453 45FB Revert to original
20. his function is used to tell program enable special functions SECOS in diagnostics interface and to log more data than required for normal operation 41 43 my 3 FoCOM user manual S E CON S www obdtester com focom 12 2 How to create ECU Snapshot Fl FeCOM Diagnostic program for Ford Mazda fo 5 77 After connection to tested control unit click on Control Zfco CM Bosch cris CA 2000 Ford Ka Unit Identification In following screen click on Save S ECU Information Choose directory to save the file and ie ap RcmIsoBoschBosch_ka_20 confirm Saving may take a few minutes mm me K7 ECU Part Number YS5T BA WFOBXXWPRBYR45412 Please send all support requests along with required data attached to support secons com Your case will be assigned unique ticket ID number in order to seCons LII NEE communicate efficiently with us Also feel free to contact us with any suggestions for improvements in the software on the same e mail address Your feedback is greatly appreciated 12 3 Unsupported control unit In case you are prompted with Unrecognized control unit window and the installed ECU is not available in the listing or you are not sure which control unit to choose or you wish to get the ECU automatically properly identified in next FoCOM version Or you just want to help us to improve FoCOM We will be more than happy to add any unsupported or unrecognized control unit to nex
21. lts such as Body Control Module No Communication Vehicle Dynamics Control Module Invalid Data Received can be safely cleared and should not re appear 30 43 FoCOM user manual SECONS 9 10 CCF Central configuration Some models use central configuration stored in two control units master copy backup For these vehicles please configure everything in CCF Master ECU see table below Some ECUs may have individual configuration using AS BUILT data www obdtester com focom Vehicle Years CCF Master CCF Slave Individual configuration Ford Mondeo 2006 2014 BCM IPC Ford Galaxy 2006 2014 BCM IPC Ford S Max 2006 2014 BCM IPC Ford Transit 2006 BCM IPC RCM Ford Focus 2010 BCM IPC APIM Ford C Max 2010 BCM IPC Ford Fiesta 2008 IPC BCM 31 43 mV vn FoCOM user manual S E C ON S www obdtester com focom 9 11 PCM configuration in VID block Mainly older control PCM units store configuration in so called VID block In order to reconfigure VID data PCM control unit flash must be completely re programmed re flashed 9 12 AS BUILT configuration Each control unit in Ford vehicles contains configuration data as hexadecimal chain In these data are encoded information from the production which specifies the functions and equipment of the vehicle Configuration data can be read from the control unit or from AS BUILT database of Ford Motor Company Note T
22. ndard csv file and it is compatible with VagScope or can be imported to Microsoft Excel or OpenOffice Calc 26 43 FoCOM user manual S E CON S www obdtester com focom 9 7 Actuators activation This function is used activate actuators and perform tests including KOEO and KOER and various actuator actions Some actuator tests may display detected fault codes at the end of the test FoCOM Diagnostic program for Ford Mazda Lo m es RCM Bosch CR16 CA 2000 Ford Ka com Actuators Tests Actuators Tests Sak EEE Key On Engine Off test Gaam EF Key On Engine Running test Main menu Che Please select actuator from the list SECONS Please note that most control units do not allow any specific actuators only KOEO or KOER tests this limitation is present also in original dealer tester 9 7 1 Key On Engine Off test KOEO test KOEO is automated powertrain module test available on most EEC V and EEC VI control units The test must be performed on stopped engine with ignition key in ON position The KOEO test may require special actions such as turning steering wheel from minimum to maximum pressing brake and accelerator pedal For vehicle specific instructions please refer to Ford service manuals All problems that were detected during the test are displayed in form of fault codes at the end of test The test terminates automatically The KOEO test should be performed before running KOER test The KOEO test may aff
23. nrwincsdnedeonndanandssteedeadonnnoatenabedsbtoantatncloaneoncs 39 11 5 Act ator RE EE 39 11 0 ee sis iieis ee VIR GENE NN Ce RUE SE o CIS I ONE Qu oa uS en a nS 40 117 Autoscan NAWO E 40 12 Reporting bugs and improvement FeQuUESE soi oe oc ee ere espe EE 41 12 1 How to create Debug E 41 12 2 How t create BECU EE 42 12 3 Uns pported contol UD o oe eoe EIS RR TD a a E E EE E REEE R 42 12 4 Problems with eot Ded UBL iae eecu ei mne eva rode ende ax ue thu eeu n hh red pp AE rU ERA NEU EU FEM REQUE 42 IE SIL UI PERTULIT DEM TR 43 m Y FoCOM user manual S E CON S www obdtester com focom 1 Introduction Thank you for purchasing the FoCOM diagnostic interface and software FoCOM is professional tool for diagnostics of Ford vehicles Please read carefully this User Manual before using the product Additional technical information is available from www DiagWiki com If you have experience with original diagnostic tool Ford IDS we recommend you to study chapter comparing both systems We hope you ll find our products useful In case you have any questions problems or feedback please contact as at support secons com We re here to help 1 1 Key features FoCOM covers for wide range of ECUs and models Fully multiplexed all in one smart USB2 0 interface Wide range of communication protocols and buses covered incl J1850 PWM ISO CAN Automatic ECU recognition Automatic vehicle scan ECU Identification Fault code
24. ntrol Module lt FACM Fuel Additive Control Module amp 4x4 Four Wheel Drive lt ATCM All Terrain Control Module lt SPCM Secondary Powertrain Control Module Main menu lt TBCM Traction Battery Control Module lt BACH Battery Control Module lt BECM Battery Energy Control Module lt FICM Fuel Injector Control Module amp GSM Gear Shift Module SECoNs ocjojlooouojiooo oi o T Fault code count in auto scan results is for some types of control units only approximate or may not be supported at all then will be zero count displayed for each ECU Please read relevant values using Read Fault Code Memory function after connecting to each ECU 18 43 FoCOM user manual S E CON S www obdtester com focom 8 Special Diagnostics Using special diagnostics you can perform the following special diagnostic tasks Se EEC IV DCL Diagnostics a diagnostics for D Geen r old EEC IV control units used in Ford vehicles to GRACOM Special Diagnostics 1996 up to 1998 for Ford Escort on mens ee Volvo Diagnostics Mondeo 2015 Diagnostics Fuel Injection Pump Diagnostics TDDI Bosch VW Ford Galeny Diagnostics a A Fuel Injection Pump Diagnostics TDDI Bosch PSG5 PSG5 diagnostic procedure described in our High Speed CAN BUS Analysis m Mid Speed CAN BUS Analysis manual Ford Fuel Injection Pump FIP coding m available at obdtester com downloads Recovery procedure
25. o one file Providing this file is required only by our technical support Based on these data we are able to monitor the whole process of performed operation and its correctness Use of debug function is important for successful resolution of any program failure or A verifying its causes For more information on how to proceed please read the following chapter Reporting bugs and improvement requests 14 43 FoCOM user manual S E CON S www obdtester com focom 6 Connecting to control units This function will display a complete list of control units You can select and connect to the specific control unit you wish to diagnose It is common that low cost vehicles have only a few control units e g PCM ABS IPC and RCM All control units present in tested vehicle can be detected by Auto scan function IE FoCOM Diagnostic program for Ford Mazda Eej a FoCOM zz cow Control Unit Selection If control unit was recognized you can use reen Powervan chasse Body _ infotainment PCM Powertrain Control Module Engine ECU diagnostic functions amp PCM Powertrain Control Module Engine ECU to 1996 In other case you should study chapter TCM Transmission Control Module Unrecognized Control Unit before using Ap TCH eee Control Modula Ii A S S FACM Fuel Additive Control Module diagnostic functions papse egere ATCM All Terrain Control Module lt gt SPCM Secondary Powertrain Control Module
26. om odometer correction 9 8 5 Reset ECU Used to reset ECU similar to ECU power supply disconnection The function is useful when recorded fault codes depend on functionality of another control unit s or after changing central vehicle configuration 29 43 FoCOM user manual S E CON S www obdtester com focom 9 9 Control unit configuration Many control units contain configurable programmable parameters FoCOM is capable of reading writing this configuration Newer cars use central configuration CCF stored usually in BCM this means that instead of configuring individual control units everything is carried out on one place Two configuration modes are supported 1 ECU AS BUILT configuration 2 ECU customization FoCOM automatically determines possible configuration modes in case of multiple choices FoCOM displays window shown on the right FoCOM Diagnostic program for Ford Mazda l Col e k BCM 2010 Ford C MAX zYcom Configuration Selection Configuration ee Control unit configuration Gen As Built data Control Unit Selection Main menu SECONS Additional technical information related to control unit configuration or retrofits is available from www DiagWiki com Reading writing configuration may require entering ECU flash programming mode This may result in fault codes related to CAN BUS FlexRay communication in other ECUs It is recommended to perform autoscan after performing any ECU configuration fau
27. ompany or other owners Mazda is registered trademark of Mazda Motor Company or other owners Jaguar Aston Martin Land Rover are registered trademarks of Ford Motor Company or other owners All trademarks used in this documentation or programs or any other material are used nominatively for identification purposes only and may be property of their respective owners 2 43 Table of Contents gece le UN RE 2 FoCOM software and driver mstallapon nennen nnne 2 1 Microsoft Windows operating E 2 2 Microsoft Windows 8 driver mstallaton nennen 2 3 Tuterfare busy issue Microsoft Windows a usen tte poer nekonanta 2 Nen LEE PI NLIS UCET TTL 24 2 Setting RN oco ERI IR tooo neue E Dd ta hu ty coi tun eui ey eee NEMESIS TREES MS SE SEENEN Me eL CETT TTE Um 6 Connecting to CODLEOL BOIS eisereen re FED REF FIR IQ AVIS SERIE Gt anu DS a i oui ai 6 1 Diagnostics of selected non standard models eese eire troie veniae DEE BEOTOEOS ee eege 6 3 Information about Ford control unts nennen nnne enne 0 4 Ford D Ee 6 5 PATS Immobilizer Passive Anti Theft System sese reb terit leta ea dk n eds aos 6 6 Diagnosticsof TCM and IG EE TL POCO SOA EE ere EUR 9 Diagnostic TRAIN eie sudare cut un eique See oi o Ea ud p cU E a oS Roe RE CH LUN Sena e culpas E S Dl UU n 9 1 Unrecognized Control EE 9 2 Control Unit Identification a6 assess nnee a a a aa a eaaa a e ta E E ai 9 3 Read fault code TAI insiren v v ARKANSAS 9 4 Clea
28. or two working days based on so called ECU snapshot file From Unrecognized ECU window or Control Unit Identification window please choose Save ECU Information button When prompted if you want to perform fast or full snapshot please choose No in order to make fast snapshot fast snapshot takes less than one minute full snapshot may take up to 15 minutes for CAN BUS ECUs or even longer for other communication protocols Please send the generated file s to support secons com For cars manufactured before 2004 we will need also VIN code of the vehicle 22 43 FoCOM user manual S E CON S www obdtester com focom 9 2 Control Unit Identification This function displays identification data provided by the ECU for example Identification data s ECU part number serial number Incomplete identification are very common mainly for older ECUs that do not provide full part number or VIN code GIS won Bee for F RCM Bosch CR16 CA 2000 Ford Ka z COM Control Unit Identification Control Unit a ECU Part Number YS5T BA Diagnostics WFOBXXWPRBYR45412 Control Unit i Ford Ka 2000 Selection Main menu SECONS Each ECU should contain valid VIN code If VIN is not supported identification should display it If it isn t provided you can program it in function ECU Programming Coding accessible from menu Control Unit Diagnostics You can print identification by clicking on Print Identifica
29. r Te EE 9 5 E 9 5 Measured valu s hive dide cacicarenssacivebe estan dade ieivite reaver aacadvabancesvescanesaad teveseesaneaueveaivoentvieas 9 6 1 Graph elegant SA TPA DI ENEE S E E E E EE eege eerste 9 0 9 Display list oisnean a E eee es eee GE ST WA ON T CN SENE TRU ER ERI NT 9 7 Key On Engine Of test ECIBU test geegent 9 7 2 Key On Engine Running test KOER 188 seen tory en ro roten row ERE Xa Re tp ep rk eU IAS 9 8 Programming Coding DUBBI cisco REP ERU NOR MR Den ea bv ma PAR RUE ELEM oI 9 8 1 PATS immobilizer coding and ECU partt p iui eerte rrt tti raa orare res 9 0 2 Diesel injector coding 7 PUG adjustment uoce uias bas rut Earned Ree EUER ERE AME RR 9 0 2 Diesel DPF fos EE aret aeo Piel tpi Once DE eat a o ead RUNE 9 8 4 Odom ter adjustment isss roceiceu ori euros YE derre Eeer Eeer pP ss MT 9 9 Control wn On EE 9 10 CCE Ne EE 31 9 11 PCM contismdton im VID Block espe pip einn n REX Ie erae d saxvormieorsanintnacetonsianes 32 KEE EI ERR TS TETTE ER 9 13 ECU Programmable parameters Gon Berat ec secta iria ees P ehe eR rues e us ds 34 DISENO ERREICHT RR 35 SNENC S C C NN 35 Eeer 35 ODS BEE E 35 913 5 e EEN 35 9 13 06 DAA NEE 36 daf EEN 36 GE 36 9 10 PEN EE 36 10 Control vint E 37 11 Ford EE PRAES I a TET LUE Om 38 IB Ede i IE selehin onsin e E E a E aE a ede 38 Re EE 38 11 3 TEE 39 11 4 Measured values I atalog O68 oisssicsisaveceroncersnedsncon
30. r of your interface as user name Password leave blank The serial number can be found in settings of FoCOM after performing test interface or on silver label of the interface We recommend you to maintain software up to data because updates provides support for new ECUs and fix various FoCOM issues We also recommend you to update firmware in diagnostic interface every time you update the software Firmware upgrade process is as follows Connect your interface via USB to your computer Go to settings of FoCOM and perform test interface Click on Apply Changes button Click on Upgrade firmware button Amore Do not disconnect the interface during upgrading the firmware 10 43 m 3 FoCOM user manual S E CON S www obdtester com focom 4 Diagnostic connectors used in Ford vehicles Location of diagnostic connector database of vehicle images is available from main menu of FoCOM 2 pin Thy TE Is used only for diagnostics of older vehicles by DCL CART protocol 4 1 3 pin 1 GND 2 DCL 3 DCL This connector is used only for diagnostics of older vehicles by DCL CART protocol 4 2 6 pin 1 gt 3 4 5 GND 6 This connector is used only for diagnostics of older vehicles using DCL CART protocol 11 43 FoCOM user manual S E C O N S www obdtester com focom 4 3 OBD I I dj 3 10
31. sed by in mn FF PCM 7 gt Somo Main menu B2445 Side impact sensor passenger side beer frans DUN improper connection 0102 PCM gt Intake system boaks B1921 Airbag diagnostic check feature ground circuit Open circuit 10102 FCM Pending e Broken or leak in indet duct from MAF semor Pending DIC Loose clamps on inlet duct P0102 PCM 72 gt E P013 PCM 7 Faulty or damaged ICM Ge S mm pom 7 Signal shorted to ground or signal return e e Permanent DIC Open ground between sensor and PCM ese s istory Signal wire open circu between sensor and PCM Opan crost peli enda BEND SECONS Open circut on YBATI connection at sensor LEN m Reading and Clearing Diagnostic Trouble Codes acted like IDS system all CMDTC Continuous Memory Diagnostic Trouble Codes are read and clear from control unit 38 43 FoCOM user manual S E CON S www obdtester com focom 11 3 Identification FA FoCOM Diagnostic program for Ford Mazds Lies zou RCM Bosch CR16 CA 2000 Ford Ka COM Control Unit Identification Loo Vive Vedisteien View Pull Dngneotg Hiec head das vesn 549 n 22 Vehicle Fiesta Marde 171 antem eege ECU Part Number YSST 27 BA ht Diagnostics WFOBXXWPRBYR45412 Capecty 15 T anaem s aic e i Ford Ka 2000 Pet Type Died en Sen RemlsoBoschBosch_ka_20 BEE nm 1s09141 K7 Opena equipment Modutes Fas GEM PCM Fut hamba YOSH PCM FLENAME FRED SECoNs Ford IDS does no
32. sure everything is OK The software should display Serial number and licenses partially hidden on screenshot on the right side Device Manager Bluetooth Manager 4 Save settings and return to main menu 5 Turn ON the ignition but don t start the engine 6 Select control unit by clicking on Select Control Unit button n In a new window choose desired control unit 9 43 FoCOM user manual SE CON S www obdtester com focom Ei FeCOM Diagnostic program for Ford Mazda Lol e FoCOM RIcom Control Unit Selection eeler Diagnostic mode Normal ll Main menu Powertrain Chassis Body Infotainment amp PCM Powertrain Control Module Engine ECU amp PCM Powertrain Control Module Engine ECU to 1996 lt TCM Transmission Control Module lt TCM Transmission Control Module III amp FACM Fuel Additive Control Module lt gt 4x4 Four Wheel Drive lt ATCM All Terrain Control Module lt SPCM Secondary Powertrain Control Module lt TBCM Traction Battery Control Module lt BACM Battery Control Module SECONS 8 If the control unit was recognized you can use diagnostic functions now In other case you must select correct type of control unit chapter Unrecognized Control Unit 3 1 Software updates Software updates in diagnostic version are available for free You can download them from http www obdtester com downloads When downloading type a serial numbe
33. t FoCOM version We are usually able to do this within one or two working days based on so called ECU snapshot file From Unrecognized ECU window or Control Unit Identification window after connecting to ECU please click on Save ECU Information button and save the file to your computer Please send the generated file s to support secons com 12 4 Problems with configuration In case you encounter any difficulties with configuration coding data please provide the following e Debug log e ECU snapshots Listing of original ECU configuration data either via saving to a file or Copy to clipboard 42 43 m 3 FoCOM user manual S E CON S www obdtester com focom 13 Known problems Connection to Japan made ABS on Mazda 3 2006 may fail this issue is related to one specific ABS ECU Above problems will be resolved in future FoCOM updates 43 43
34. t provide this function however is possible to display some identification information in Log Viewer Technician View Full Diagnostic FoCOM use special function for reading identification information 11 4 Measured values Datalogger emm prem EZE E COM RCM Bosch CR16 CA 2000 Ford Ka Icom Measured Values Graph View ARPMDES A SORPM Measured Values Graph View 1 0 d Battery Positive Voltage ELICIT EE Control Unit t Dagnostis esi Modi Goa 8 870 V Control Unit SE iz ct Tc Selection die en i ni rre Main menu P r E 7311 Dag t i E sru 1899891 t i ej EDS ES SECONS Unlike IDS system the FoCOM implements three options of displaying measured values Graph for comparison two measured values simultaneously in graph Display 3x3 appropriate for see display from longer distance Display list for display all available measured values It isn t necessary to set vehicle equipment which is sometimes hardly observable FoCOM displays all measured values provided by control unit The FoCOM can sometimes display more values than IDS system e g in Engine control unit is commonly available distance moved from last clearing flash memory this function isn t supported in IDS system 11 5 Actuator activation Actuator activation is implemented in same way like IDS system 39 43 FoCOM user manual S E CON S www obdtester com focom 11 6 Programming function
35. tallation In case of problem with installing drivers on Windows 8 64 bit please follow these steps Press Windows Key R In the window that appears type shutdown exe r o f t 00 Press OK button The System will restart to a Choose an option screen Select Troubleshoot from Choose an option screen Select Advanced options from Troubleshoot screen Select Startup Settings from Advanced options screen Click Restart button System will restart to another Startup Settings screen Select Disable Driver Signature Enforcement press number on keyboard for option shown on screen F7 or 7 Once the system starts install the diagnostic interface drivers as you would on Windows 7 e 00 19 Ui amp Lahr e e Em Y Windows Vista amp 7 required signed all sys files we use usbser sys shipped by Microsoft with valid digital signature Final version of Windows 8 requires also signed inf file which is not in our case The above procedure helps to override unsigned inf file Once driver is installed the program will work properly Startup Settings Press a number to choose from the options below number keys or fu 1 Enable debugging able Safe Mode w 7 Disable driver signature e able early launch anti malware protection 9 Disable automatic restart after failure Press F10 for more options Press Enter to return to your operating system 7 43 FoCOM user manual S E C O N S www obdtester com
36. tion button or you can copy to clipboard by clicking on Copy Identification button Save ECU Information button is used to save ECU snapshot of tested control unit as mentioned in chapter Unrecognized Control Unit or Reporting bugs and improvement requests 23 43 FoCOM user manual S E CON S www obdtester com focom 9 3 Read fault code memory This function allows you to read and display diagnostic trouble codes saved in control unit memory COM RCM Bosch CR16 CA 2000 Ford Ka zcom Fault Code Memory Fault Code enl Memory irbag lamp circui Control Unit B1869 Diagnostics oe B2444 Side impact sensor driver side Selection Main menu B2445 Side impact sensor passenger side B1921 Airbag diagnostic check feature ground circuit Open circuit Functions vn Nae ees Clear Fault Codes Stored DTCs Pending DTCs z Em Present DTCs DTC History ates msn SECONS Please note that some ECUs mainly those used in Jaguar do not support fault code reading at all Also ECUs that run in bootloader mode e g the ECU is not properly programmed do not allow fault code reading In such case special message is displayed Static error is simply the opposite of Sporadic and Intermittent When a DTC is JA marked Sporadic or Intermittent it means the fault condition that set the DTC did not exist or could not be detected at time the DTC read out was performed 9 4 Clear Fault Codes This function clears
37. ts COM amp LPT Bluetooth Manager is a preparation to upcoming bluetooth feature The button is currently inactive Expert functions Development functions Enables additional functions under development This setting is not saved before program exit and will be cleared on every application start Do not enable this option unless requested by SECONS support staff as these functions may be dangerous to use without proper instructions Expert mode Enables additional functions such as special coding functions or additional configuration options These functions are intended for experienced technicians and are provided on AS IS basis with absolutely no guarantee It is highly recommended to leave this option unchecked This mode also eliminates some warning messages and questions Protocol settings You can set various timings for each communication protocol This is advanced feature used for example when problems occur with connection to control unit caused by slower ECU response and the like Restore Defaults this button restores all modified timings of all protocols to default values Changing protocol settings is not required before normal use of the program You will be asked to make changes by our tech support when solving your issue at support secons com if necessary Debug functions By clicking on Save Debug button you can capture the latest data from elapsed communication between control unit and program int
38. uage choose language of diagnostic application user interface in the drop down menu Units type you can choose metric or imperial unit system for measured values Refresh this button refreshes COM port selection drop down list Correct COM port number should be already chosen after connecting diagnostic interface via USB to PC and clicking on Refresh button If not choose correct COM port number from the list It is needed in order to perform successful interface test Test interface before each use of program please test proper function of your connected interface by clicking this button After successful test you can see a serial number of your interface displayed below the COM port field then firmware version and information about active licenses Activate license this button is used for activating new license s to use the program or special functions Internet connection is required Standard license is already activated for all interfaces before purchase Upgrade firmware use this button to upgrade firmware in your diagnostic interface every time after installing the latest software version available at www obdtester com downloads Do not disconnect your interface during upgrading the firmware 13 43 m vn FoCOM user manual S E CON S www obdtester com focom Device Manager is used to finding out correct COM port number or to reinstall drivers Your device appears as ELM USB Interface COMx under Por
39. ue 9 13 3 Revert to original Reverts currently selected value to original state 9 13 4 Undo all changes Reverts to original configuration as retrieved from the control unit when entering this window 9 13 5 Go back Returns back to diagnostic menu 35 43 m 3 FoCOM user manual S E CON S www obdtester com focom 9 13 6 Load Loads configuration from a file Data file is checked if matches the connected control unit 9 13 7 Save Saves configuration to a configuration file for restore or configuration transfer or to a text file report 9 13 8 Copy Copies configuration to operating system clipboard 9 13 9 Print Prints configuration 36 43 m 3 FoCOM user manual S E CON S www obdtester com focom 10 Control unit memory programming Flash and serial memory programming functionality will be available shortly in special FOCOM programming module flash programming is available to selected beta testers only paid feature 37 43 FoCOM user manual S E CON S www obdtester com focom 11 Ford IDS and FoCOM comparison This chapter describes comparison of functions of FoCOM with original Ford Motor Diagnostics IDS Integrated Diagnostic System 11 1 Control unit selection REESE casus Mee M RN FoCOM Body gt JON Control Unit Selection Chis E amp Dectrical gt Control Unit gnostic mode Powertrain Ld Main menu Powertrain Chassis Body Infotainment beide HU 2 PCM Po
40. very easily using these commands Diagnostic interface should be then visible from the FoCOM diagnostic application 2 4 3 Installation Programs can be installed by launching setup exe file using wine e g wine FoCOMSetup exe e I You can download the latest version of FOCOM from www obdtester com downloads 8 43 FoCOM user manual S E CON S www obdtester com focom 3 First steps 1 Connect the FoCOM interface to your computer 2 Connect the FoCOM interface to OBD II connector in the vehicle You can use picture gallery for find it available from main menu OBD II Connector Location button D FoCOM Diagnostic program for Ford Mazda Sas Y FoCOM Diagnostic program for Ford Mazda Fe e es Data Link Connector Location Ford Focus 2005 GXCOM Find vic ZACOM oic image DLC Image Find DLC Main menu Choose a car from this tree to view OBD II connector location Main menu Escort 1995 s Expedition 2003 Fiesta 2007 Focus 1999 s Focus 2002 ge Eius Focus 2011 Galaxy 1995 Ka 1999 Mondeo 1993 Mondeo 2000 SeCons LL em SECONS 3 Set up FoCOM application EE Refresh Select Settings from FoCOM main menu and configure interface port After clicking on Refresh button FoCOMap 0 1 2241 Zeie software should find port to which FoCOM interface is ae ibo dm connected Choose this port Then click on Test Interface Upgrade firmware to make
41. wertrain Control Module Engine ECU s RER ae lt PCM Powertrain Control Module Engine ECU to 1996 om TCM Transmission Control Module tc TCM Transmission Control Module III ZEN saaan amp FACM Fuel Additive Control Module m Rolrievo CMDICs ez 4x4 Four Wheel Drive ATCM All Terrain Control Module lt SPCM Secondary Powertrain Control Module TBCM Traction Battery Control Module lt BACM Battery Control Module SECONS as m Main difference between concepts of program FoCOM and system IDS is in user approach to vehicle and its systems The IDS uses so called Function system which first chooses function e g Read trouble codes and then control unit e g PCM FoCOM chooses control unit first and then function Advantage of second approach is especially similarity with other diagnostic systems e g VCDS etc and consequently more user friendly for those who have not much experience with IDS Next advantage is easier identification of concrete type of control unit for programming etc 11 2 Fault codes m n Pee NE RN RCM Bosch CR16 CA 2000 Ford Ka Select Option Powertr an Control Module d Zou Fault Code Memory Description DIE E Fault Code Memory B1869 Airbag lamp circuit ICM CMDICs Control Unit MAE Sensor Circuit Low Input This DIC is set when the MAI sensor signal is Se ew M arts B2444 Side impact sensor driver side mmm FF PCM Lan This DIC may be cau
42. y Management System reset lt ECU Reset SECONS Please read carefully all manuals for specific coding operations The manuals are available online from our website www obdtester com focom Additional technical information is available also from www DiagWiki com 28 43 m vn FoCOM user manual S E ON S www obdtester com focom 9 8 1 PATS immobilizer coding and ECU pairing These functions are used to add code new keys to a vehicle More detailed description is available in our PATS coding manual 9 8 2 Diesel injector coding pump adjustment FoCOM supports diesel injector classification coding and fuel pump adjustments on diesel PCM control units where applicable More detailed description is available in our Ford TDCi Injectors coding manual 9 8 3 Diesel DPF regeneration FoCOM supports static dynamic diesel particulate filter regeneration and reset options on diesel PCM control units where applicable More detailed description is available in our Ford DPF service manual 9 8 4 Odometer adjustment This function is available in IPC control unit and is used to adjust mileage when replacing odometer FoCOM is capable of changing value up where instrument cluster supports this function In addition to the above function special paid module exists that allows changing odometer to any desired value on both new and used instrument cluster More information about this paid function is available at http obdtester com foc
Download Pdf Manuals
Related Search