Model 660 Actuator for Trailer Brakes
Contents
1. is out of the lines Replenish the brake fluid during the bleeding process so the level does not fall below half full level in the master cylinder reservoir When bleeding and testing is completed make sure master cylinder is filled to 3 8 below the top of the reservoir and filler cap is securely in place Instruction 08162 TIE DOWN ENGINEERING 255 Villanova Drive SW Atlanta GA 30336 www tiedown com 404 344 0000 Fax 404 349 0401 IE ENGINEERING ObS119 C12Z50 Check with your state motor vehicle department for laws concerning minimum trailer brake requirements Some states may require brakes on all axles Road test trailer a short distance to activate the actuator several times Check fluid level again Remember low brake fluid levels will result in hitch ball knocking When testing is completed make sure master cylinder is filled to 3 8 below the top of the reservoir and filler cap is securely in place Road test again to make sure brakes work properly RATED CAPACITY Maximum Actuator Capacity 6600 Ibs Gross Load 660 Ibs Maximum Tongue Load The actual in service rating is limited to that of the ball and hitch being used or the trailer manufacturer s G V W R shown on the certification label whichever is lower Note G V W R is the Gross Vehicle Weight Rating which includes the trailer and the load weight as a Total Gross Weight HITCHING TRAILER 1 The vehicle towing hitch and ball must have a ra2. length DANGER Tongue weight beyond rating limits will interfere with performance of actuator and braking system and the tow vehicle 9 The actuator is designed for use with Free Backing trailer brakes To block braking action in order to back up with other types of brakes use an electric solenoid For trailer movement when brakes are not required place the safety pin in the hole on the side of the actuator housing to block movement of the actuator DANGER Failure to remove pin will also prevent forward braking Pin must be in the lower forward hole as a safety lock for the hitch ball coupler latch when towing at all times MAINTENANCE 1 Always check the brake fluid reservoir before using trailer Make sure it is at least half full If not re fill to 3 8 inch below the top of the reservoir with DOT 3 brake fluid Check for leaks and repair as required Never reuse brake fluid 2 To extend coupler and ball life coat both with a thin coating of grease This will also eliminate squeaking Wipe clean and renew film each time trailer is used 3 Examine the actuator for bent parts or wear each time the trailer is used Replace parts as necessary 4 There are no user adjustments on the actuator 5 Actuator travel shown by coupler roller path over one inch indicates a need to adjust the brakes or add fluid to the reservoir or a need to bleed the brakes and check connections for leaks Adjust per instructions found in brake installation man
3. 0 Fax 404 349 0401 WARNING If button stop cable is showing Release emergency stop cable by prying spring out with a flat blade screw driver ne DOWN ENGINEERING 053013 C366 Technical Service Bulletin Drill Hole Pattern for the Model 66 660 70 700 amp 80 800 Standard Housing Actuators June 18 2012 Model 66 660 Actuators 2 bolts only e Model 66 660 requires 2 1 2 x 4 Grade 5 bolts with lock washers not included e Model 70 700 amp 80 800 Actuators requires 3 1 2 x 4 Grade 5 bolts with lock washers not included o All TIE DOWN ENGINEERING standard actuators have the same hole pattern for consistent hole placement Page 8 Instruction Sheet 08074 TIE DOWN ENGINEERING 255 Villanova Drive SW Atlanta GA 30336 www tiedown com 404 344 0000 Fax 404 349 0401 DOWN 071814009
4. ETY CABLE SPRING 15 4 10554 1 4 SPRING LOCK WASHER ZINC 16 1 50301 6600 SAFETY PIN amp CABLE 17 1 10503 SCREW 1 4 20 x 1 2 SELF TAP 18 1 50317 66 70 amp 80 E STOP CABLE ASSEMBLY Page 4 Model 660 Drum Brake Parts Detail Model 660 Manufactured after March 2012 6 600 Ibs Capacity Drum Brake Ready ITEM NO QTY PART NUMBER DESCRIPTION 1A 1 70461C MODEL 66 COUPLER 1B 1 70461DM MASTER CYLINDER ASSY 2 1 70462 1 2012 MODEL 66 FORMED ACTUATOR HOUSING 3 1 70462 2 2012 MODEL 66 ACTUATOR HOUSING BRIDGE PLATE 4 1 70462 3 2012 MODEL 66 FRONT COVER PLATE 5 1 70462 4 2012 MODEL 66 REAR COVER PLATE 6 2 47245 ROLLER FOR 17018 6600LB ACTUATOR 7 2 47246 1 2 20NF x 4 L BOLT 8 2 10661 NUTLOCK REVERSE 1 2 20 ZINC 9 1 70470 4 MODEL 66 amp LP70 MOLDED MASTER CYLINDER CAP 10 1 70470 3 MODEL 66 amp LP70 MASTER CYLINDER PAPER GASKET 11 4 10518 BOLT HHCS 1 4 20 x 3 4 GR 5 ZINC 12 6 10548 10 32 HEX WASHER HEAD THREAD ROLLING SCREW ZINC 13 1 48844 SAFETY CABLE SPRING 14 4 10554 1 4 SPRING LOCK WASHER ZINC 15 1 50301 6600 SAFETY PIN amp CABLE 16 1 10503 SCREW 1 4 20 x 1 2 SELF TAP 17 1 50317 66 70 amp 80 E STOP CABLE ASSEMBLY Page 5 TIE DOWN ENGINEERING LIMITED WARRANTY Limited Warranty TIE DOWN ENGINEERING Inc TIE DOWN warrants its products to be free from defects in material and workmanship for one year from date of delivery to th
5. Installation Instructions and Service Manual Model 660 Actuator for Trailer Brakes 6 600 Ibs Capacity Drum Brake Ready or Disc Brake Ready US Patents 6 375 211 and 8 342 559 MODEL 66 660 ACTUATOR INSTALLATION INSTRUCTIONS IMPORTANT READ AND UNDERSTAND THE ENTIRE INSTRUCTION ASSEMBLY PROCEDURE BEFORE INSTALLING YOUR BRAKES AND ACTUATOR The Model 660 works by the surge or push of the trailer toward the tow vehicle This automatically synchronizes the trailer brakes with the tow vehicle axle brakes When the trailer pushes against the tow vehicle the actuator telescopes together and applies the force to the master cylinder supplying hydraulic pressure to the brakes The built in dampening shock absorber retards the telescoping shock against the hitch ball Be sure to comply with regulations for brakes in your state Brake laws sometimes are minimum standards and you may wish to add additional brakes to your trailer Read your tow vehicles owner s manual on towing capacity and other towing recommendations before installing brakes or this actuator The Model 660 Actuator is completely assembled and ready to bolt into place Tongue sizes 3 x 3 3 x 4 amp 3 x 5 1 Bolt the actuator to the tongue using grade 5 bolts 1 2 inch in diameter 4 inches long Lightweight tongues less than 11 gauge require spacer tubes inside the tongue for reinforcement Attachment strength should equal or exceed than 1 1 2
6. e original purchaser when properly installed used and maintained by the purchaser This warranty does not apply to damage or loss caused by any or all of the following circumstances or conditions e Damage caused during installation e Parts accessories materials or components used with or replacing any TIE DOWN braking system not obtained from or approved in writing by TIE DOWN e Misapplication misuse and failure to follow the directions or observe cautions and warnings on installation operation application inspection or maintenance specified in any TIE DOWN quotation acknowledgement sales literature specification sheet or installation instruction and service manual applicable literature e Use of product in any other application other than those described in TIE DOWN s product information materials If any TIE DOWN products are found upon TIE DOWN s examination to have been defective when supplied TIE DOWN will either credit the purchaser s account for the purchase price of the TIE DOWN product replace the TIE DOWN product or repair the product TIE DOWN has sole discretion in choosing which option to provide For this LIMITED WARRANTY to apply TIE DOWN must receive notice of the alleged defect within 30 days of either the discovery of the alleged defect or the expiration of the warranty period whichever is earlier Any claim not made within this period shall conclusively be deemed waived If requested by TIE DOWN purchase
7. e purchaser is rendered and the difficulty is found not to be with TIE DOWN s product the purchaser shall pay the time and expense at the prevailing rate at the time of service of seller s field representative s Charges for service labor and other expenses that have been incurred by the purchaser its customer or agent without prior written authorization of TIE DOWN will not be accepted TIE DOWN EXTENDS NO WARRANTY EXPRESS OR IMPLIED ON PRODUCTS NOT MANUFACTURED BY TIE DOWN OR TO TIE DOWN S DESIGN SPECIFICATION INCLUDING BUT NOT LIMITED TO SUCH ITEMS AS NON TIE DOWN TIRES BRAKES ACTUATORS BEARINGS HOSE AND TUBING PURCHASER S RECOURSE SHALL BE LIMITED TO ANY WARRANTY OF THE RESPECTIVE MANUFACTURERS THIS WARRANTY EXCLUDES ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY PURPOSE THIS WARRANTY DOES NOT COVER NOR EXTEND TO INCIDENTAL OR CONSEQUENTIAL DAMAGE Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state No representative has authority to make any representation promise or agreement except as stated in this Limited Warranty TIE DOWN reserves the right to make design and other changes upon its products without any obligation to install the same on any previously sold or delivered produc
8. r shall return the alleged defective product to TIE DOWN for examination at purchasers expense TIE DOWN will not pay for expenses incurred in returning a product to TIE DOWN without TIE DOWN s prior written authority TIE DOWN shall not be liable for any other expenses purchaser incurs to remedy any defect Purchasers waive subjugations on all claims under any insurance Limitation of Liability It is expressly agreed that the liability of TIE DOWN is limited and TIE DOWN does not function as an insurer THE REMEDIES SET FORTH IN THIS WARRANTY SHALL CONSTITUTE THE EXCLUSIVE REMEDIES AVAILABLE TO THE PURCHASER OR USER AND ARE IN LIEU OF ALL OTHER REMEDIES EXPRESS OR IMPLIED THE LIABILITY OF TIE DOWN WHETHER IN CONTRACT IN TORT UNDER ANY WARRANTY OR OTHERWISE SHALL NOT EXCEED THE PURCHASE PRICE OF THE PARTICULAR PRODUCT MANUFACTURED SOLD OR SUPPLIED BY TIE DOWN To Obtain Technical Assistance To enable TIE DOWN to respond to a request for assistance or evaluation of customer or user operating difficulty please provide at a minimum the following information by calling 1 800 241 1806 e Model number serial number and all other data on the specific component which appears to be involved in the difficulty e The date and from whom you purchased your TIE DOWN product e State your difficulty being sure to mention at least the following Application Nature of load involved and Weight of the load Field Service If field service at the request of th
9. t may over stress the connection between the trailer and tow vehicle as this could result in damage to the actuator WARNING DO NOT REUSE BRAKE FLUID Always use fresh DOT 3 fluid from a fresh container Failure to maintain proper levels of fluid in the reservoir will cause brake failure WARNING Failure to install the hitch pin before towing can result in accidental opening of the coupler hitch latch which can lead to the trailer coming off of the hitch ball causing serious damage injury or death If pin will not fit into the front lower hole the coupler is not attached properly Re set coupler on hitch ball WARNING A minimum of 5 tongue weight and a maximum 10 tongue weight of the trailer G V W R must be located on the hitch ball The Trailer tongue should be parallel to the ground Too much weight can cause premature brake actuation and loss of control of the towing vehicle To little tongue weight can cause the trailer to fishtail resulting in loss of control of the tow vehicle and trailer total trailer weight G V W R includes weight of the trailer plus load WARNING A loose fit between the coupler and hitch ball can cause the actuator and hitch ball to separate causing serious damage injury or death Check coupler every time prior to towing and at each stop on long trips Always make certain that coupler latch safety pin is securely installed into coupler latch WARNING Brake laws sometimes are minimum standards and you may
10. times trailer G V W R 2 Hydraulic brake lines should be installed on the trailer as described in the installation manual supplied with the brakes Note Some disc brakes require the use of flexible brake lines at the connection POINT on the brake caliper Follow brake manufacturer instructions 3 Use only DOT 3 heavy duty brake fluid in the Model 660 actuator Use a pressure type brake bleeder to bleed brakes This type of brake bleeder is available at your local automotive jobber Follow manufacturer s directions Or manually bleed the brakes using a heavy duty flat blade screwdriver inserted in the hole provided on top of the actuator near the front Insert the screwdriver and use a pumping action to activate the master cylinder in order to bleed the brakes See page 7 for more details To bleed master cylinder and brakes install bleeder hose on first wheel cylinder to be bled if tandem axle trailer bleed closest axle first and the closest brake on that axle first Use a loose end of hose from the bleeder valve submerged in a glass container of brake fluid to observe bubbling hose must be submerged into clean brake fluid to keep air from traveling back into the brake cylinder Loosen the bleeder screw located in the wheel cylinder one turn the system is now open to the atmosphere The bleeding operation for that brake is complete when bubbling stops Be sure to tighten bleeder screw securely Each wheel cylinder must be bleed until all air
11. ting equal to or greater than trailer G V W R 2 Model 660 will accept 2 trailer hitch balls only Trailer balls larger than 2 00 or out of round will not fit the coupler or may result in coupler failure Balls smaller than 1 970 can cause shock loading and sudden disconnection Make certain ball latch is in correct position to retain the hitch ball Push latch until safety latch engages plate below latch Insert safety pin into forward hole as a safety lock for the hitch ball coupler prior to towing Do not tow trailer if coupler is damaged 3 Connect safety cables or chains using crossed pattern under tongue or follow trailer manufacturer s directions 4 Connect actuator breakaway cable S hook to the tow vehicle only Do not connect S hook to the safety cables or chains 5 The breakaway system is designed to only operate after the trailer detaches from the tow vehicle and the safety chains have failed The breakaway is not a parking brake Do not use as such 6 Ifthe breakaway is accidentally applied while un hitching insert a flat bladed screwdriver into the spring clip on the side of the actuator and pry sideways pressure to release see page 7 7 Any control devices that restrict operation of the actuator cannot be used This includes certain sway control devices The actuator must be free to telescope in response to braking requirements 8 Equalizing or weight distributing hitches may be used allow six to eight inches free chain
12. ts DUE TO THE WIDE VARIATION IN USES TO WHICH TIE DOWN PRODUCTS WHEELS HUBS BRAKES ETC ARE SUBJECTED BY USERS WE ARE UNABLE TO SPECIFY CARRYING CAPACITIES OR SPEEDS FOR A PARTICULAR APPLICATION THEREFORE THE MANUFACTURER MUST TEST HIS EQUIPMENT UNDER THE MOST SEVERE CONDITIONS TO DETERMINE THAT TIE DOWN PRODUCTS ARE SUITABLE THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THOSE DESCRIBED ABOVE EFFECTIVE JANUARY 2001 THIS WARRANTY SUPERSEDES ALL PRIOR WARRANTIES WRITTEN OR IMPLIED Page 6 TIE DOWN ENGINEERING 255 Villanova Drive SW Atlanta GA 30336 www tiedown com 404 344 0000 Fax 404 349 0401 ENGINEERING Instructions for Bleeding Tie Downs Model 660 750 amp 850 Actuators Place Screwdriver W Tip Here Bleeding Access Correct Incorrect Front of Bracket 9 DO NOT USE SLOT a e To pump master cylinder insert a flat tip screwdriver into the round hole near the front of the actuator cover See 1A The screwdriver should be at the lowest angle possible to the actuator so that it slides in front of the e stop bracket See 1B Screwdriver tip MUST BE IN FRONT of the e stop bracket and NOT in the slot on the e stop bracket See 2A Push the screwdriver forward and back to pump the master cylinder See 2B Normal Operation Emergency Stop Position DO NOT TOW TRAILER Page 7 TIE DOWN ENGINEERING 255 Villanova Drive SW Atlanta GA 30336 www tiedown com 404 344 000
13. ual In general back off adjusters on drum brakes from locked position as required Adjust Free Backing brakes by rotating in forward direction only Failure to adjust may result in loss of braking Disc brakes do not require adjustment check for pad wear Page 2 WARNING Actuator and brakes should always be flushed with fresh water after using trailer in corrosive conditions This includes salt water fertilizers and other corrosive materials Before storing trailer remove brakes and clean thoroughly It is also wise to repack the bearings at the same time Failure to properly and adequately maintain the actuator could cause serious damage injury or death WARNING The breakaway system is not designed to operate if the trailer does not separate completely from the tow vehicle or if the tongue goes under the rear of the tow vehicle WARNING In the event that the breakaway system is used check all system components cable S hooks etc for proper working order Replace any damaged parts with genuine Tie Down parts only WARNING When re setting the break a way system keep hands and fingers clear as you re set the mechanism hydraulic pressure held in the system may cause the assembly to snap back suddenly WARNING AVOID sharp turns which can cause the actuator to bind or jackknife against the tow vehicle or cause a bend in the tongue Either can damage the actuator causing brake failure AVOID towing trailer across large bumps or dips tha
14. wish to add additional brakes to your trailer Read your tow vehicles owner s manual on towing capacity and other towing recommendations before installing brakes or this actuator WARNING NEVER ALLOW THE COUPLER LATCH SAFETY PIN TO REMAIN IN THE REVERSE LOCKOUT POSITION HOLE AFTER REVERSE MANEUVERING ALWAYS INSERT COUPLER LATCH SAFETY PIN BACK INTO COUPLER LATCH FAILURE TO REMOVE SAFETY PIN FROM REVERSE LOCK OUT POSITION HOLE WILL PREVENT FORWARD MOVEMENT BREAKING WHICH CAN RESULT IN SERIOUS PROPERTY DAMAGE INJURY OR DEATH Page 3 Model 660 Disc Brake Parts Detail Model 660 Manufactured after March 2012 6 600 Ibs Capacity Disc Brake Ready W Solenoid Installed ITEM NO QTY PART NUMBER DESCRIPTION 1A 1 70461C MODEL 66 COUPLER 1B 1 70461M MASTER CYLINDER ASSY 2 1 70462 1 2012 MODEL 66 FORMED ACTUATOR HOUSING 3 1 70462 2 2012 MODEL 66 ACTUATOR HOUSING BRIDGE PLATE 4 1 70462 3 2012 MODEL 66 FRONT COVER PLATE 5 1 170462 4 2012 MODEL 66 REAR COVER PLATE 6 2 47245 ROLLER FOR 17018 6600LB ACTUATOR 7 2 47246 1 2 20NF x 4 L BOLT 8 2 10661 NUTLOCK REVERSE 1 2 20 ZINC 9 1 70470 4 MODEL 66 amp LP70 MOLDED MASTER CYLINDER CAP 10 1 70470 3 MODEL 66 amp LP70 MASTER CYLINDER PAPER GASKET 11 1 11286 VALVE SOLENOID 2WNC OPTIONAL BACK FLOW 12 4 10518 BOLT HHCS 1 4 20 x 3 4 GR 5 ZINC 13 6 10548 10 32 HEX WASHER HEAD THREAD ROLLING SCREW ZINC 14 1 48844 SAF
Download Pdf Manuals
Related Search