BODY SHOP ADMINISTRATION MANUAL FOR CERTIFIED EV
Contents
1. Removal of both Li ion battery pack and related parts include Judgment standard No high voltage parts damage no concave no dents and no cracks B High voltage system parts and relevant harnesses that are placed around the damaged area The car will be and obstruct body transported to the EV repair amp painting x2 dealer s workshop Installation of both Li ion battery pack and related parts include incidental work high voltage parts Removal is required as Install the Service plug The car will be transported to the dealer s workshop LANTA WARNING X3 If vehicle damage is so severe the high voltage system components including Li ion Battery cannot be removed unless it is drawn out by frame straightening equipment a technician from the EV dealer will visit the body shop and assist the body shop to safely straighten the frame and remove the high voltage system parts Failure to have a certified EV technician remove or install EV High Voltage parts could result in serious personal injury or death Customer 5 Process Procedure Details for Body Repair and Painting X4 Incase of being unable to turn off the safety plug The floor panel located in service plug will be transformed in a large damage and that will result in the replacement of the floor panel lt Procedure gt Cut the transformed floor panel such as a red dotted line Bend the floor panel and secure the2. Precautions for towing gt 1 Location of towing hook Location of towing hook attachment point The hook is stored in the left side of the luggage room 2 For any of the following conditions turn the power switch to the OFF position wear insulated gloves disconnect service plug and transport the vehicle using a vehicle transport vehicle e High voltage parts or wiring harnesses are damaged e Drive system brakes suspension or tires are damaged e Coolant leakage is detected e READY lamp does not turn ON when power switch is in the ON position 4 5 Preparation of Estimate Sheet Preparation of Estimate Sheet Body shop Body shop estimator shall give an estimate for the total cost of repair e Include any special requests from the customer to the estimate worksheet e Include services provided by a certified EV dealer such as removal of related parts identification of reusable and non reusable parts and include them in the estimate worksheet lt Estimation sheet details gt Category Description Certified E V Body shop dealer vehicle Parts removal installation labor han ae Body repair and paint refinishing labor Transportation fee Certified E V dealer Body shop Body shop Certified EV dealer Inspection fee Inspection using CONSULT III ha ia plus Cost to be agreed on with the insurance company Inspection fee and removal fee of related parts Transportation fee Body r
3. a possibility of sudden SRS Airbag inflation due to harness short circuit or damage and it may cause serious injuries Refer to ESM for details 7 1 High Voltage Precautions Failure to follow any of the following WARNINGS could result in serious personal injury or death Because electric vehicles contain a high voltage battery there is the risk of electric shock electric leakage or similar accidents if the high voltage component and vehicle are handled incorrectly Be sure to follow the correct work procedures when performing inspection and maintenance Be sure to remove the service plug in order to shut off the high voltage circuits before performing inspection or maintenance of high voltage system harnesses and parts Be sure to put the removed service plug in your pocket and carry it with you so that another person does not accidentally connect it while work is in progress Be sure to wear the Appropriate protective equipment consisting of gloves shoes and glasses face shield before beginning work on the high voltage system Clearly identify the persons responsible for high voltage work and ensure that other persons do not touch the vehicle When not working cover high voltage parts with an insulating cover sheet or similar item to prevent other persons from contacting them There is the possibility of a malfunction occuring if the vehicle is changed to READY status while the service plug is removed Therefore do not c
4. dealer B 07 After finalizing the repair charges for the vehicle the body shop will charge the insurance company or certified EV dealer in the case of self pay repairs for the following items based on the contents of the consignment contract Part expenses Labor charge technical fee Inspection fee at certified EV dealer A Transport fee from certified EV dealer to the body shop check with certified EV dealer regarding the cost A Transport fee from the body shop to certified EV dealer Note items with A are charged if a transportation fee was incurred 4 12 Installation of Related Parts and Final Inspection E Installation of related parts Certified EV dealer Body shop Install related parts that are removed in section 4 3 e Damaged parts are to be replaced in accordance with service part establishment E Final inspection Certified EV dealer Body shop The certified EV dealer performs final inspection using CONSULT III plus and confirms the repair of the vehicle is complete 4 13 Invoice to customer Certified EV dealer Body shop Based on the invoice from the body shop the certified EV dealer will create an invoice 4 14 Vehicle Delivery to Customer m Vehicle Delivery Process Certified EV dealer Inform the customer of the delivery date of the vehicle When the customer comes to the store confirm the contents of the repair in the presence of the customer on the actual vehicle Ex
5. opening to turn off the safety plug 6 Precautions for Body Repair and Painting Removal and installation of high voltage parts including Li ion battery pack and related harness Never allow the removal and installation of high voltage parts including Li ion battery pack or related harnesses to be performed by body shop technicians If removal and installation of high voltage parts and harnesses is necessary to support the body repair always have body shop contact certified EV dealer so that technicians of certified EV dealer can be dispatched to body shop to perform component removal and installation Failure to have a certified EV technician remove or install EV High Voltage parts could result i in serious personal injury or death rion control of painting booth When a paint booth is used at the body shop to prevent Li ion Battery deterioration ensure the paint booth temperature is controlled to 140 F 60 C or less when measured at the vehicle s outer sill See A below If the paint booth temperature is more than 140 F 60 C have the Li ion Battery removed from the vehicle by the certified EV dealer and then deliver the vehicle to body shop Failure to remove the Li ion oe prior to ooo ro it to temperatures above 140 F 60 C could result in Li ion Wide a Mini 42510A Extech Instruments IR Thermometer Corporation sc oS A a gt j BA EK SF A A A Outer sill temperature measurement part L SO SEN jl
6. to the customer regarding repairs not covered by insurance to be borne by the customer and gain approval for the work Flow of estimate feedback Certified EV Customer Body Shop j dealer SA Customer 4 8 Ordering Parts Ordering Parts Certified EV dealer The certified EV dealer will issue an order for parts to National Sales Company NSC based on the request from the body shop confirm the parts order against the estimate worksheet e f the promised delivery date is delayed due to back ordered parts negotiate the schedule with the body shop and be sure to gain the customer s consent 4 9 The Repair of Cars Involved in an Accident m Repair of an Accident Car Certified EV dealer Body shop f additional work is required inform the customer via the insurance company or certified EV dealer service advisor SA and gain the consent of both the customer and the insurance company to perform work In cases where the repair schedule is delayed due to additional work inform the certified EV dealer of the scheduled completion date and gain the customer s consent 4 10 Arranging for transport m Arranging for Transport Body shop Body shop Certified EV dealer Transport from the body shop to the certified EV dealer should be arranged by the body shop based on the consignment contract For details see 4 4 Arranging for Transport 4 11 Finalize repair coat E Finalize Repair Cost Certified EV
7. to the outsourced body shop if it is more convenient for the customer Reception Because related components including Transport between the certified high voltage parts xare removed by a EV dealer and an outsourced certified EV dealer a transportation fee is body shop added to the customer s account Refer to 3 4 and 3 10 for details After being repaired at an outsourced body shop vehicles will be returned to the Completion inspection certified EV dealer where the high voltage parts are to be reinstalled and a final quality inspection using CONSULT IIIplus X Related parts are parts located in surrounding area of vehicle damage and include high voltage parts that may cause an obstacle for body repair and painting 3 Business Consignment to Outsourced Body Shops When the business consignment contract is finalized the certified EV dealer shall make an offer to the outsourced body shop The contents of the business consignment contract should be prepared referencing the following items e Consigning party and e Dealing with accident during the consigned party term of consignment e Consignment fee e Re repair e Term of contract e Confidentiality etc e Delivery and receipt of vehicles Removal and installa related parts and fi Request for body repair Outsourced inti z body shop B amp P entry and painting Customer Carrying in out vehicle X Related parts are parts loca
8. Draft as of Aug 1 9 2010 Update as of Sep 215 2010 Final Version as of Oct 15 2010 Revised Version as of Nov 1 24 2010 BODY SHOP ADMINISTRATION MANUAL FOR CERTIFIED EV DEALER Global Aftersales Planning Dept Nissan Motor Co Ltd Forewo rd This manual describes the body and paint repair processes that dealers should follow as they are related to the Nissan Leaf Electric Vehicle This vehicle is equipped with a high voltage Li ion Battery pack Improper repair procedures may result in serious consequences such as electrocution Please read this manual before beginning any body or paint repair procedures on the LEAF Electric Vehicle Follow the instructions to ensure a safe repair IMPORTANT INFORMATION FOR SAFETY DESCRIPTION You will see various symbols in this manual They are used in the following ways This is used to indicate the presence of a hazard that will cause DANGER death To avoid or reduce the risk the procedures must be followed precisely This is used to indicate the presence of a hazard that could cause death or serious personal injury To avoid or reduce the risk the procedures must be followed precisely This is used to indicate the presence of a hazard that could cause minor or moderate personal injury or damage to your vehicle To avoid or reduce the risk the procedures must be followed carefully Please note that there may be differences between the information provided in this manu
9. M If a sill cover resin is included remove the a ee x OO H sill cover to measure the temperature 6 Precautions for Body Repair and Painting e For spot welding and CO2 arc welding High voltage parts are not connected to ground and therefore are not affected by spot welding or CO2 arc welding Removal of high voltage parts is therefore not necessary Always wear appropriate personal protective equipment when working on or around the EV 7 In the event of an accident LN e Be sure to check the READY lamp on the combination meter and verify that the READY indicator lamp is off and the high voltage system is stopped e There is a possibility of remaining high voltage in the air conditioning system by the Remote Air Conditioning System even when the READY lamp is turned OFF and the Air Conditioning Indicator is turned ON Please ensure that the Air Conditioning Indicator lamp is turned OFF and the Air Conditioning System is inactive e After High Voltage System shut down please wait for 10 minutes to complete discharging the high voltage condenser While waiting do not operate e The High Voltage System full dischage takes 10 minutes but after 5 minutes the voltage has dropped below 60V e Remove the 12 Volt battery negative terminal and wait for 3 minutes Even though the 12 Volt battery negative is disconnected the Supplemental Restraint System SRS Airbag maintains voltage for 3 minutes There is
10. al and the actual vehicle you are working on due to specification changes All information specifications and illustrations in this manual are those in effect at the time of printing NISSAN reserves the right to change specifications or design at any time without notice Table of Contents 1 Summary of Body Repair Work Flow 2 High Voltage Parts Requiring Removal 3 Business Consignment to Outsourced Body Shops 4 Work Flow from Certified EV Dealer to Body Shop 4 1 Customer Reception and Vehicle Processing 4 2 Identifying Related Parts 4 3 Removal of Related Parts 4 4 Arranging for Transport 4 5 Preparation of Repair Estimate 4 6 Approval to Start Repairs from Insurance Company Customer 4 7 Feedback to Estimate 4 8 Ordering Parts 4 9 Repair of Damaged Vehicles 4 10 Arranging for Vehicle Transport 4 11 Finalize Repair Cost 4 12 Installation of Related Parts and Final Inspection 4 13 Invoice to Customer 4 14 Vehicle Delivery to Customer 5 Process Procedure Details for Body Repair and Painting 6 Precautions for Body Repair and Painting 7 In the Event of an Accident 7 1 Protection for Electric Shock 7 2 In the Event of Li ion Battery Pack Damage 1 Summary of Body Repair Work Flow Return of the vehicle for installation of both Li ion battery pack and high voltage parts Is it the minor damage Customer t A EV Dealer s workshop Body shop X1 The minor damage There i
11. e customers may want to repair just small scratches on the bumper etc In such a case where to consign the repair work may be determined by the Certified EV dealer in consultation with the customer Inform the customer that repairs by the body shop entail a transportation fee lt Regarding the transport fee gt To ensure the safety of body shop personnel EV Li ion Battery and High Voltage parts located near the damaged portion of the vehicle shall be removed and installed by a certified EV dealer Certified EV dealers have the facilities equipment and exclusively trained technicians to safely service your vehicle Failure to have a certified EV technician remove or install EV Li ion Battery and High Voltage parts could result in serious personal injury or death Transportation fees are necessary to move the vehicle between the certified EV dealer and body shop These fees are invoiced to the insurance company or the customer 4 2 Identifying Related Parts E Identifying related parts STETE Bodyshop Identify parts including high voltage parts that may cause an obstacle for body repair and painting by referring to the BRM section of Electronic Service Manual ESM Check related parts for damage and determine whether or not the related part is reusable 4 3 Removal of related parts m Removal of related parts STETE Bodyshop Remove related parts including high voltage parts and retain parts at the servic
12. e department of the certified EV dealer For removal procedures of related parts refer to the following manual Welding panel parts BRM section of ESM Exterior parts interior parts high voltage parts glass parts ESM e The following precautions are for the safe storage of removed high voltage parts JARNIN To prevent electric shock immediately apply insulation protection using insulation tape on removed high voltage connector terminals and any damaged portion or parts Failure to apply insulation protection to high voltage connectors terminals or damage parts could result in serious personal injury or death Refer to ESM for details 4 4 Arranging for Transport E Arranging for Transport Ceritiea EV dealer Certified EV dealer Body shop lt Precautions for transporting a vehicle gt To prevent further vehicle damage caused by electricity generation by the vehicles motor always transport the vehicle with front wheels drive wheels or all 4 wheels raised as illustrated Lift up 4 wheels Completely secure the vehicle Always release the parking brake See Parking brake manual release described in the Owners Manual Never tow with the front wheels on the ground or four wheels on the ground forward or backward Otherwise induced electricity is generated by drive motor 4 4 Arranging for Transport E Arranging for Transport J Certified EV dealer Body shop ia ial lt
13. epair and others 4 saat Transportation fee Certified EV dealer Certified EVdealer Inspection fee and installation fee of related parts Related parts are parts located in surrounding area of vehicle damage and include high voltage parts that may cause an obstacle for body repair and painting 4 6 Approval to start repairs from Insurance Company Customer E Approval to start repairs Certified EV dealer Body shop After preparing an estimate worksheet the body shop should send it to the customer s insurance company by e mail with a digital picture attached or fax etc In the presence of a representative of the insurance company obtain an approval to start the repair 4 7 Feedback to Estimate Body shop gt Certified EV Dealer eae eSend the estimate worksheet description of damage repair and repair cost prepared by the body shop to the certified EV Dealer and explain the contents of the repair e After gaining the approval of the insurance company and the customer the person in charge of parts in the body shop should order parts from the certified EV dealer e Explain to the certified EV dealer about repairs that are not covered by insurance to be borne by the customer Certified EV Dealer SA gt Customer EAGER e The certified EV dealer should explain to the customer about the contents of the repair parts used repair costs and the substitution fee e Provide an explanation
14. hange the vehicle to READY status unless instructed to do so in the Service Manual 7 1 High Voltage Precautions HIGH VOLTAGE HARNESS AND EQUIPMENT IDENTIFICATION e The colors of the high voltage harnesses and connectors are all orange Orange High Voltage labels are applied to the Li ion battery and other high voltage devices Do not carelessly touch these harnesses and parts HANDLING OF HIGH VOLTAGE HARNESS AND TERMINALS e To prevent electric shock immediately apply insulation protection using insulation tape on removed high voltage connector terminals and any damaged portion or parts Failure to apply insulation protection to high voltage connectors terminals or damage parts could result in serious personal injury or death REGULATIONS ON WORKERS WITH MEDICAL ELECTRONICS e The vehicle contains parts that contain powerful magnets If a person who is wearing a pacemaker or other medical device is close to these parts the medical device may be affected by the magnets Such persons must not perform work on the vehicle e If you use any medical electric devices such as an implantable cardiac pacemaker or an implantable cariovascular defibrillator check with the electric medical device manufacture concerning the effects that charging may have on implanted devices before starting the charge operation If you have an implantable cardiac pacemaker or an implantable cardiovascular defibrillator while the battery is charg
15. ing Do not stay inside the vehicle Do not go inside the vehicle for example to remove or place an item in the passenger compartment Do not open the trunk for example to remove or place item in the trunk charging may affect the operation of electric medical devices and result in serious personal injury or death 7 1 High Voltage Precautions PROHIBITED ITEMS TO CARRY DURING THE WORK e Because this vehicle uses components that contain high voltage and powerful magnetism do not carry any metal products which may cause short circuits or any magnetic media cash cards prepaid cards etc which may be damaged on your person when working POSTING A SIGN OF DANGER HIGH VOLTAGE REPAIR IN PROGRESS DO NOT TOUCH e To call the attention of other workers indicate High voltage Repair in progress Do not touch on vehicles where work is being performed on the high voltage systems aBueyo L ul uosied IHONOL LON OG SS3ed90dd NI diVday SADVLIOA HOIH HSADNVG VY ZS DANGER HIGH VOLTAGE REPAIR IN PROGRESS DO NOT TOUCH Person in charge Copy this page and put it after folding on the roof of the vehicle in service 7 2 In the event of Li ion Battery pack damage 1 In the event of Li ion Battery fluid electrolyte solution leakage e Always wear the appropriate Personal Protective Equipment PPE to wipe up electrolyte solution leakage using a dry cloth The used cl
16. ledge complete replacement Traction Motor Inverter DC DC J B Front side member partial replacement Li ion Battery Service plug Charge port Front Side Li ion Battery High Voltage Harness Connector Front side member complete Li ion Battery Service plug Charge port Front Side Li ion Battery High Voltage replacement Harness Connector PTC Elements Heater Traction Motor Electric Compressor Traction Motor Inverter DC DC J B 2 High Vo t age Parts Requiring Removal O High voltage parts requiring removal when replacing welded panel components 2 Side body Under body 6 Outer Front Pillar partial replacement Li ion Battery Service plug Front Side Li ion Battery High Voltage Harness Ce outer sitpanarepsconent o Rear Fender paralrenicoment Rear panel replacement Rear Side Member Extension replacement Rear Floor Rear replacement Li ion Battery Service plug On Board Charger Front Side Li ion Battery High Voltage Harness Connector 3 Business Consignment to Outsourced Body Shops Certified EV dealers that do not own an in house Body amp Paint shop it will be necessary to negotiate and sign a business consignment _agreement with an outsourced body shop Xx Points to keep in mind when consigning business to an outsourced body shop Even if the repair is consigned customer reception and processing should be handled at the certified EV dealer In some cases customers may drive the vehicle
17. nt immediately and extinguish the fire if possible If you must walk away from the vehicle notify an appropriate responder or a rescue person of the fact that the vehicle is an electric car and contains a high voltage system and warn all others
18. oth must be disposed in accordance with any local state or federal requirements e Li ion Battery Electrolyte Solution Characteristics Clear in color Neutral Sweet odor Similar viscosity to water Skin irritant Eye irritant If contact with eyes rinse with plenty of water and see a doctor immediately Highly flammable Ensure the accident site is well ventilated Electrolyte liquid or fumes that have come into contact with water vapors in the air will create an oxidized substance This substance may irritate skin and eyes In these cases rinse with plenty of water and see a doctor immediately Since the Li ion battery is made up of many small sealed battery modules electrolyte solution will not leak in large quantity Note Other fluids in the vehicles are the same as those in a conventional internal combustion vehicle 7 2 In the event of Li ion Battery pack damage 2 Vehicle Fire e In the case of extinguishing a fire with water large amounts of water from a fire hydrant if possible must be used DO NOT extinguish fire with a small amount of water Small amounts of water will make toxic gas produced by a chemical reaction between the Li ion battery electrolyte and water e Use a fire extinguisher Type ABC effective for an electrical fire fire caused by wiring harnesses electrical components etc and oil fire fire caused by oil etc e In case of vehicle fire contact fire departme
19. plain the repair contents repair cost maintenance contents etc f any fare paying repair is involved have the charge paid X Maintenance charge such as inspection of Charging system Wheel alignment adjustment and replacement of LLC etc The service advisor SA or sales person in charge will make a follow up telephone call about a week after the delivery 5 Process Procedure Details for Body Repair and Painting Certified EV dealers work shop Customer In house or outsourced y body shop Bring the car to the EV dealer s work X 1 Refer to 1 Summary of Body Repair Work Flow shop X2 Stated in the BRM for each operation unit Check if the EV i Check for malfunctions system warning using CONSULT III indicator is lit Plus and visual inspection Identify the malfunctioning high voltage system part Not lit Check if there is any Identify the damaged After disconnecting 12V damage as described part and verify the battery negative terminal l below high voltage system remove the Service plug 4 There is only a part parts that need to scratch or unevenness be removed After waiting 10 minutes on an outer panel or measure the residual voltage bumper and there is no of the high voltage system part damage to high voltage A High voliage system to make sure that it is 5V or system parts 1 part parts that require less removal due to damage as well as relevant harnesses
20. s only a scratch or unevenness on an outer panel fender door etc or bumper X2 The temperature of paint booth Refer to 6 Precautions for Body Repair and Painting for details Ifthe paint booth temperature is more than 140 F 60 C have the Li ion Battery removed from the vehicle by the certified EV dealer and then deliver the vehicle to body shop X3 High voltage parts except for Li ion battery pack Traction Motor Inverter D C D C J B Traction Motor Electric Compressor P TC Elements Heater On Board Charger Service plug Charge port Front Side Li ion Battery High Voltage Harness Connector 2 High VoltagePar t s Requiring Removal O High voltage parts requiring removal when replacing welded panel components 1 Front body E Layout of high voltage parts Service plug DC DC J B Traction Motor Inverter Charge port Li ion Battery A Z Je N Electric PTC Elements Heater This component include a DC DC converter ee and high voltage junction box J B wa Major welding operation items High votage parts requiring removal Radiator Core Support Li ion Battery Service plug Charge port Front Side Li ion Battery High Voltage Harness Connector Hood ledge partial replacement Hood ledge partial replacement partial replacement Li ion Battery Service plug Charge port Front Side Li ion Battery High Voltage Harness Connector PTC Elements Heater Traction Motor Electric Compressor EE Hood
21. ted in surrounding area of vehicle damage and include high voltage parts that may cause an obstacle for body repair and painting 4 Work Flow from a Certified EV Dealer to Body Shop The following are the assignments and workflow from receipt of a vehicle that has been in an accident to vehicle delivery to the customer after repair completion Detailed work processes are described from the next page forward Certified EV dealer Body Shop 1 Customer reception and vehicle processing Service advisor SA or Sales person 5 Preparation of estimate sheet 6 Approval to start repair from insurance company customer 7 Estimate feedback 8 Ordering parts 9 Vehicle repair 11 Finalize repair cost 13 Invoice to customer 14 Vehicle delivery to customer Related parts are parts located in surrounding area of vehicle damage and include high voltage parts that may cause an obstacle for body repair and painting 4 1 Customer Reception and Vehicle Processing Certified EV dealer Certified EV dealer When a customer requests repairs to be done to a car that has been in an accident the Service Advisor SA or a sales person will process the request f the vehicle is insured check if the insurance company has been informed When the vehicle arrives perform a walk around check in the presence of the customer Certified EV dealer will consign the repair to the body shop Note Som
Download Pdf Manuals
Related Search