combination speedometer/tachometer gauge kit - Harley
Contents
1. cMOTOR HARLEY DAVIDSON GENERAL Ga INSTRUCTIONS COMBINATION SPEEDOMETER TACHOMETER GAUGE KIT REV 2015 04 24 is03400 U S Department of Transportation National Highway Traffic Safety Administration Title 49 United States Code Subtitle VI Motor Vehicle and Driver Programs Part C Information Standards and Requirements Chapter 327 Odometers Section 32703 Preventing tampering A person may not 1 advertise for sale sell use install or have installed a device that makes an odometer of a motor vehicle register a mileage different rom the mileage the vehicle was driven as registered by the odometer within the designed olerance of the manufacturer of the odometer 2 disconnect reset alter or have disconnected reset or altered an odometer of a motor vehicle intending to change the mileage registered by he odometer 3 with intent to defraud operate a motor vehicle on a street road or highway if the person knows hat the odometer of the vehicle is disconnected or not operating or 4 conspire to violate this section or section 32704 or 32705 of this title Section 32704 Service repair and replacement a Adjusting mileage A person may service repair or replace an odometer of a motor vehicle if the mileage registered by the odometer remains the same as before the service repair or replacement If the mileage cannot remain the same 1 the person shall2. DIAL changes backlight color for tachometer and speedometer LCD changes backlight color for LCD display speedometer changes speedometer needle color or tachometer changes tachometer needle color 3 Turn ignition switch OFF Turn switch back to ACCY The gauge displays the color number of the current color 4 See Table 3 and Figure 5 Press and hold the trip reset button to quickly cycle through the colors Release the trip reset button to stop cycling through the colors or Press and release the trip reset button repeatedly to slowly cycle through the colors 5 Turn ignition switch OFF Turn the switch back to ACCY to save the color The gauge displays SAVED and returns to the display color select menu 6 Turn the ignition switch to OFF or IGN to return to normal operation 40f5 Figure 5 Select Display Color Table 3 Color Guide Number Range Color 000 015 Red 016 030 Amber Orange 031 060 Yellow 061 100 Yellow Green 101 180 Green 181 250 Green Blue 251 350 Blue 351 380 Blue Violet 381 440 Violet 441 490 Pink 491 525 Red 526 600 White Light Colors Note Color descriptions and color ranges are approximate Table 4 Troubleshooting Operation Problem Possible Cause Possible Solution Copying odometer data Gauge does not display per Gauge has already conducted odo _ Install gauge and confirm function centage check
3. and ok meter copy process or the gauge ality might not have power Copying odometer data Gauge does not display per Vehicle ignition switch not in ign Turn to ign centage check and ok _ position Copying odometer data Gauge does not display per Vehicle run stop switch not in run Turn to run centage check and ok _ position Copying odometer data Gauge starts percentage but Gauge lost communication to vehicle Turn vehicle ignition switch to off does not complete bus electrical system or gauge not and run stop switch to stop wait compatible with vehicle incorrect fit 15 seconds and retry ment or model year Copying odometer data Gauge reads no cal or vin Normal software functionality None needed Confirm that the err before starting count down gauge displays percentage check and ok The gauge is functioning properly Installation into vehicle harness LCD states no cal Gauge did not conduct copy odometer process Conduct copy odometer process in i sheet Installation into vehicle harness LCD states vin err Gauge was already married accu mulated 31 1 miles 50 km to another vehicle Reinstall on previous vehicle to confirm no vin err Entering set up mode Will not go to set up mode Loose connection with gauge con nector or trip reset button Check for bent accessory pin 6 in gauge connector or check trip reset b
4. adjust the odometer to read zero and 2 the owner of the vehicle or agent of the owner shall attach a written notice to the left door frame of the vehicle specifying the mileage before the service repair or replacement and the date of the service repair or replacement b Removing or altering notice A person may not with intent to defraud remove or alter a notice attached to a motor vehicle as required by this section Section 32705 Disclosure requirements on transfer of motor vehicles a 1 Disclosure requirements Under regulations prescribed by the Secretary of Transportation that include the way in which information is disclosed and retained under this section a person transferring ownership of a motor vehicle shall give the transferee the following written disclosure A Disclosure of the cumulative mileage registered on the odometer B Disclosure that the actual mileage is unknown if the transferor knows that the odometer reading is different from the number of miles the vehicle has actually traveled 2 A person transferring ownership of a motor vehicle may not violate a regulation prescribed under this section or give a false statement to the transferee in making the disclosure required by such a regulation 3 A person acquiring a motor vehicle for resale may not accept a written disclosure under this section unless it is complete A This subsection shall apply to all transfers of motor vehi
5. before pro ceeding 00251b 1 See the service manual Remove seat and main fuse NOTE Cover painted parts to protect finish 2 See the service manual Remove the instrument console from the fuel tank Place an H D Service Cover or clean shop towels on the fuel tank Turn the instrument console upside down and lay it on the covering 3 See the service manual Remove the original equipment OE speedometer Install the new speedometer 4 See the service manual Install the instrument console to the fuel tank WARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b J05306 NOTE When the main fuse is installed and battery power is applied to the electrical system the security light flashes for up to 15 seconds while the new gauge synchronizes to the ECM 5 See the service manual Install the main fuse seat WARNING Be sure headlamp tail and stop lamp and turn signals are operating properly before riding Poor visibility of rider to other motorists can result in death or serious injury 00478b 6 Turn the ignition switch to IGN but do not start the motorcycle Check operation of all lamps 7 Check the speedometer and tachometer for proper opera tion and verify that the odometer reading is correct NOTES The replacement speedometer will be
6. cles unless otherwise exempted by the Secretary by regulation except in the case of transfers of new motor vehicles from a vehicle manufacturer jointly to a dealer anda person engaged in the business of renting or leasing vehicles for a period of 30 days or less B For purposes of subparagraph A the term new motor vehicle means any motor vehicle driven with no more than the limited use necessary in moving transporting or road testing such a vehicle prior to delivery from the vehicle manufacturer to a dealer but in no event shall the odometer reading of such vehicle exceed 300 miles 5 The Secretary may exempt such classes or categories of vehicles as the Secretary deems appropriate from these requirements Until such time as the Secretary amends or modifies the regulations set forth in 49 CFR 580 6 such regulations shall have full force and effect J05306 amp Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled Please dispose of materials responsibly Figure 1 Title 49 United States Code GENERAL CONTINUED Table 1 Speedometer Features Available Models Features Gear Indicator Trip B Fuel Level Range Clock Colored Backlighting Dyna 2004 2007 Yes Yes Yes Yes 2008 Yes Yes Yes Yes Yes 2009 2011 Yes Yes Yes Yes Yes Yes Softail Except FLSTSE 2004 2007 Yes Yes Y
7. come locked to the ECM after 31 1 miles 50 km have been accumulated The trip B odometer displays the countdown mileage Once the countdown reaches zero the speedometer is locked to the ECM If installed on another vehicle the odometer displays VIN ERR If the speedometer is removed from the vehicle before the countdown reaches zero it has not been locked to the ECM This mileage countdown allows for a road test to verify that speedometer replacement was the proper repair e The 31 1 miles 50 km countdown period before the speedometer is locked to the ECM the security light flashes for up to 15 seconds when battery power is restored to the electrical system while the new gauge synchronizes to the ECM e Gear Indication display is a calculated gear position based on wheel and engine speed The gear position displayed could be momentarily inaccurate depending on rider clutch use characteristics and clutch wear This momentary false reading although unlikely can occur if the clutch is allowed to slip either due to excessive wear poorly adjusted clutch or if the operator rides the clutch e If gauge is installed on a motorcycle with ABS verify that the ABS warning lamp is working properly See the owner s manual for ABS warning lamp operation e The odometer will display VIN ERR and the ABS warning lamp will illuminate if the gauge is installed on anon ABS vehicle after the gauge is locked accumulated 31 1 miles 50 km into a
8. es Yes 2008 2010 Yes Yes Yes Yes Yes Yes Road King Except FLHRSE3 and FLHRSE4 2004 2007 Yes Yes Yes Yes 2008 2013 Yes Yes Yes Yes Yes Yes Notes 1 New functionality Kit Numbers Table 2 Kit Numbers Kits Description 70900070B Gauge Speedo Tach MPH 70900071A Gauge Speedo Tach KMH 70900072A Gauge Speedo Tach MPH KMH Models For model fitment information see the P amp A Retail Catalog or the Parts and Accessories section of www harley davidson com English only Service Manual Required WARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation One is available from a Harley Davidson dealer Kit Contents This kit contains a combination spoeedometer tachometer and an adapter harness There are no service parts available with this kit J05306 COPY ODOMETER DATA NOTE The gauge displays NO CAL no calibration It will not function if it is installed before the odometer copying process is per formed 1 Verif
9. gnition switch to ACC Then release the trip reset button The gauge displays SETUP and shows the fuel level display 2 Press the trip reset button to toggle through different dis plays until the brightness function is selected The gauge displays SETUP BRIGHT and shows the full range of gear numbers 1 6 3 Turn the ignition switch quickly to OFF and then back to ACCY to toggle between BRIGHT and DIM settings 4 Press the trip reset button to toggle to the next display control or turn the ignition switch to OFF or IGN to return to normal operation and save the setting Clock Adjustment 1 To adjust clock on gauge toggle to the clock display 2 Press and hold trip reset button Choose 12 hour or 24 hour clock by pressing and holding trip reset button 3 The hours flash Press trip reset button quickly to adjust to desired time Press and hold trip reset button 4 The minutes flash Press trip reset button quickly to adjust to desired time Press and hold trip reset button 5 AM or PM flash Press trip reset button to select Press and hold trip reset button Display Color 1 Press and hold the trip reset button Turn ignition switch to ACC Then release the trip reset button The gauge displays SETUP and shows the fuel level display 2 Press the trip reset button to toggle through different dis plays until the display color function is selected The gauge displays COLOR ALL changes all display colors at once
10. n ABS vehicle e 2007 and earlier vehicles do NOT support the gear indic ator display function Battery Reconnection and Initialization After the battery is reconnected or a new gauge is installed the gauge requires about a half tank of fuel to initialize fuel range miles to empty functionality During consumption of the first full tank of fuel the gauge software begins the process of learning your riding patterns eventually tailoring the fuel range calculations to your unique riding characteristics The fuel level display and tank mounted fuel gauge may not always match when starting with a full tank of fuel The tank 3 0f 5 fuel gauge utilizes a continuous sweep needle to indicate fuel level while the speedo tach fuel level utilizes a segmented display Each segment represents 1 8 of a tank For example if a given segment just came on or is about to go off it would show no change while the needle on the tank mounted gauge would likely show a change in position Fuel Fill up and Top off When adding fuel it is recommended you add at least 2 gallons of fuel to update the fuel and range displays If the fuel display does not update immediately after the vehicle is put in motion the fuel and range displays will slowly update over the next 30 miles Press and hold the Trip reset switch to toggle between the mile and kilo displays DISPLAY MODIFICATION The backlight color can be modified for the entire gauge or
11. the dial speedometer pointer tachometer pointer and display separately The gear indication and fuel level display can also be disabled Fuel Level Display 1 See Figure 4 Press and hold the trip reset button Turn ignition switch to ACC Then release the trip reset button The gauge displays SETUP and shows the fuel level display 2 Turn ignition switch OFF Turn switch back to ACCY to toggle the fuel level display from ON to OFF 3 Press the trip reset button to toggle to the next display control or turn the ignition switch to OFF or IGN to return to normal operation and save the setting is07365 30 o 100 ne Aa 120 Figure 4 Fuel Level Display Setup Gear Indicator Display 1 Press and hold the trip reset button Turn ignition switch to ACC Then release the trip reset button The gauge displays SETUP and shows the gear indicator display 2 Press the trip reset button to toggle through different dis plays until the gear indicator function is selected The gauge displays SETUP and shows the full range of gear numbers 1 through 5 or 6 3 Turn ignition switch OFF Turn the switch back to ACCY to toggle the gear indicator display from ON to OFF J05306 4 Press the trip reset button to toggle to the next display control or turn the ignition switch to OFF or IGN to return to normal operation and save the setting Backlight Brightness 1 Press and hold the trip reset button Turn i
12. utton operation Gear Indication Gear Indication does not operate Not turned on Use instruction sheet to turn on gear indication in set up mode Gear Indication Gear Indication does not operate Vehicle is 2007 or earlier N A Fuel Level Fuel Level does not operate If Sportster check for proper install of Use instruction sheet for proper fuel sender install Color Changing Color will not save Color was not saved properly Use instruction sheet for proper saving procedure Note Please contact Technical Service with any installation or troubleshooting questions before filing a warranty claim J05306 5of5
13. y that the engine OFF RUN switch is in the RUN position 2 Turn the ignition switch to the ACCY position and note the odometer reading 3 Turn ignition switch OFF 4 See the service manual and Figure 2 Locate data link connector 91 5 Remove the rubber plug from the data link connector 91 Install the 4 way connector of the adapter harness from the kit 6 Install the 12 way connector of the adapter harness to the new gauge Hold the gauge during the copying process NOTE If odometer copy process is done repeatedly in a short time span it displays the percentage countdown CHECK and OK Refer to Troubleshooting Guide Table 4 The display could be difficult to read in low light conditions 7 Turn ignition switch ON See Figure 3 The gauge rapidly displays the percentage of copying complete Then the gauge displays CHECK and finally OK When OK displays the copying process is successful 8 Turn ignition switch OFF 9 Disconnect the adapter harness from the data link con nector 91 and the gauge Install rubber plug 20f5 Rubber plug Data Link Connector 91 4 Way adapter harness connector 12 Way adapter harness connector Speedometer OP ONS Figure 2 Connect Speedometer to Copy Odometer Data Figure 3 Speedometer Gauge Displaying OK INSTALLATION IWIN NIN To prevent accidental vehicle start up which could cause death or serious injury remove main fuse
Download Pdf Manuals
Related Search