7 - Advance Adapters
Contents
1. ADVANCE ADAPTERS INC P N 716805 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 3 OF 10 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 08 05 10 MANUAL STEERING CONVERSION JEEP UNIVERSAL STEERNG COLUMN The stock steering column is the easiest option when installing the Saginaw steering If you are planning to use a custom steering column some fabrication will be necessary for mounting The stock steering column protrudes through the firewall and into the engine compartment where it enters the stock Jeep worm gear steering mechanism The steering box must be disassembled so that the worm portion of the steering column shaft can be cut off Once removed the end of the shaft must be machined to fit the universal joint provided The diameter of this shaft must be machined to fit a 7 8 875 universal joint After the shaft has been machined the column can be reassembled with the modified shaft To support the shaft in the center of the column a bushing P N 716810 fits into the column housing with a precision fit on the shaft Make sure the bushing and the shaft have sufficient clearance for easy turning The column will then need to be assembled into the support plate The new steering shaft bushing must be installed into the bottom of the steering column so that alignment and support of the shaft is maintained With the bushing in place you can now install the universal yoke Slip the yo2. If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores ADVANCE ADAPTERS INC P N 716805 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 10 OF 10 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 07 09 13 MANUAL STEERING CONVERSION JEEP UNIVERSAL Installation Tips We recommend Weldless DD and Double Splined universal joints for the best steering system Weldless DD universal joint features two set screws for maximum holding power Position yoke tighten set screws to mark the shaft Remove yoke and drill the set point on the shaft When installing the universal joint set screws are tightened into the countersink mark then tighten the jam nut and the shaft will not move We recommend the use of Loctite Spline both ends 3 4 36 universal joint is the preferred design as it allows the shaft to be rotated in small increments during installation to properly align or phase the steering system Once the steering is set tighten set screws to mark the shaft Remove
3. and other related equipment These manuals are normally available at automotive dealerships and parts stores ADVANCE ADAPTERS INC P N 716805 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 2 OF 10 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 08 05 10 MANUAL STEERING CONVERSION JEEP UNIVERSAL The Saginaw steering conversions for these vehicles is a proven advantage simply because they allow you to have better control of your vehicle both on and off the highway The problem with stock steering on these vehicles is excessive play or backlash In addition to offering a sound positive means of controlling your vehicle it can be performed at a reasonable cost Additional advantages include exhaust clearance engine positioning and custom steering columns These kits fit Jeep vehicles only Before you consider this conversion we recommend that you thoroughly read and understand the complete installation procedure Do not take shortcuts on steering installations We recommend that these conversions be installed by a qualified technician The control of your vehicle depends on your steering performance Failure of your steering system can result in severe damage and possible injury Most Jeep vehicles had basically the same stock configuration It is simply a gear box at the base of the steering column which controls a drag link towards the front of the vehicle The bellcrank is mounted on the front crossmemb
4. compartment Once in position the plate must be completely welded to the frame Since this plate encounters extreme forces from the steering system the welding of this plate should be done by a certified welder We have provided a pair of 3 16 thick steel frame enclosures to box in both of your frame rails providing a good base for welding the steering box mounting plate The steering box mounting plate must have a solid surface for welding and positioning The extra plate is simply supplied for boxing of the passenger side frame rail On vehicles equipped with winches it may be necessary to offset the winch bumper to allow for the steering box clearance When using mounting plate P N 716826 you will be required to have this plate welded onto your frame rail This plate is made of steel so that a good weld can be made These welds should be made only by a qualified welder Do not short change your installation with a poor quality weld of these mounting plates to your frame rail The plates should be welded along the complete perimeter We have included a special frame to steering mounting plate gusset P N 716832 to provide additional support from the outside of your frame rail to the bottom of the steering box mounting plate power steering plate shown in this photo SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible w
5. yoke and drill the set point on the shaft When installing the universal joint set screws are tightened into the countersink mark then tighten the jam nut and the shaft will not move We recommend the use of Loctite Optional Equipment 716863 Collapsible Steering Shaft 3 4 DD X 1 DD comes without any universal joints 716841 Universal Joint 1 DD X 1 DD 716843 Universal Joint 1 DD X 7 8 716844 Universal Joint 3 4 DD X 800 36 spline 716845 Universal Joint 1 DD X 3 4 36 spline 716846 Universal Joint 1 DD X 800 36 spline 716848 Universal Joint 3 4 DD X 1 48 spline 716849 Universal Joint 3 4 DD X 1 DD 716850 Universal Joint 3 4 DD X 3 4 36 spline 716851 Universal Joint 3 4 DD X 3 4 DD 716852 Universal Joint 3 4 36 spline X 3 4 36 Spline A FEW NOTES Dhasing Keep the forks of the yokes closest to each other in line and parallel to the centerline of the shaft to avoid binding X X Always use the minimum angle when designing your system ideally 10 degrees or less NEVER MORE THAN 35 DEGREES x ENEVER WELD a universal joint Welding reduces the strength of the metal and can melt the needle bearing seal x BUFFING creates a very attractive finish in a matter of minutes Itis very important not to buff the caps because over heating may damage the bearing seals SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversi
6. you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores ADVANCE ADAPTERS INC P N 716805 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 9 OF 10 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 08 05 10 MANUAL STEERING CONVERSION JEEP UNIVERSAL FRAME RAIL Ms MOUNTING PLATE Part No 716834 N Part No 716826 FRAME ENCLOSURES Part No 716824 GUSSET A Stock Jeep or our Part No 716821 LONG TIE ROD TA 2 a E a a Part No 716816 Wa pee A a da ll F a E PITMAN ARM a Dei fi LOCKWASHER amp NUT pa I Tet he a 3 Mta i ee i it ies ho d te Stock Jeep or our Se Part No 716821 E CENTER SOCKET TIE ROD END a i Hs beste Part No 716819 Left hand thread STOCK CLAMPS Stock Jeep or our Part No 716820 SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible warranty or return privileges
7. ADVANCE ADAPTERS INC P N 716805 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 Telephone 800 350 2223 MANUAL STEERING CONVERSION PAGE 1 OF 10 Fax 805 238 4201 Page Rev Date 11 04 15 JEEP UNIVERSAL KIT CONSISTS OF No Qty PartNo Description 1 1 716810 COLUMN BUSHING 2 4 716812 CLAMP Tie Rod 3 1 716814 CLAMP Spud Shaft 4 1 716816 PITMAN ARM MANUAL 5 1 716823 MOUNTING PLATE 6 2 716824 FRAME ENCLOSURE 7 1 716826 BLK MOUNTING PLATE 8 1 716829 SHORT TIE ROD 9 1 716830 LONG TIE ROD 10 1 716832 GUSSET 11 1 716834 30B SPUD SHAFT 12 1 716847 7 8 UNIVERSAL FLAMING RIVER 13 1 716841 STEERING UNIVERSAL JOINT 1 DD X 1 DD 14 1 716863 STEERING SHAFT 36 COLLAPSIBLE W O U JOINT 15 2 723122 5 16 FLAT WASHERS 16 1 723703 3 8 NYLOCK NUT 17 1 723704 WASHER 18 1 723725 3 8 16x 2 BOLT 19 3 724324 HIGH COLLAR WASHER 20 3 724347 7 16 x 1 1 2 GRD 8 12 PT BOLTS Kit does not include the Saginaw Steering Box Steering Hoses or New Tie Rod Ends for Military Replacement May of 2013 Advance Adapters started updating its steering spud shafts to a male double D design If you have a steering box that requires the 36 tooth steering spud shaft you will need P N 716834 36 instead of 716834 30 P N 716834 30 Spud shaft 730 dia x 30T manual amp power male side is 1 double D as of 5 24 13 P N 716834 36 Spud shaft 730 dia x 36T manual male side is 1 dou
8. AF The control shaft between the end of the column and the steering box spud shaft is defined as the steering shaft With each kit we have provided a 3 4 DD X 1 DD shaft that has a length of 36 The shaft can be shortened to the necessary length for your installation The new shaft assembly has a 3 4 DD end that will need to fit into the steering column universal joint Use the same procedure to spot drill both of the set screws and Loctite the connections with the two lock nuts The lower connection Use the same procedure to spot drill both of the set screws and Loctite the connections with the two lock nuts Always use Loctite on the double set screws and lock nuts for all universal yoke connections P N 716863 UNIVERSAL JOIN OR STEERING COLUMN ee a 49 ee DOUBLE D 3 4 DIAMETER SHAFT COMBINED ANCLES COLLAPSIBLE INTERMEDIATE SHAF NOT TO EXCEED 7 0 DOUBLE D 1 DIAMETER a scat Ea SPUD SHAFI 10 STEERING GEAR BOX SPUD SHAFT CLAMP P N 716841 Universal Joint 1 DD X 1 DD P N 716843 Universal Joint 1 DD X 7 8 P N 716844 Universal Joint 3 4 DD X 800 36 Spline P N 716845 Universal Joint 1 DD X 3 4 36 Spline P N 716847 Jeep column shaft 3 4 DD x 7 8 P N 716846 Universal Joint 1 DD X 800 36 Spline P N 716853 Universal Joint 3 4 DD x 3 4 30 P N 716854 Universal Joint 1 DD X 3 4 30 ROUTING THE STEERING SAF
9. E amp SAFETY WIRE MOUNTING PLATE 716823 BUSHING 716810 WELD CLAMPTO MOUNTING PLATE UNIVERSAL YOKE 716847 7 8 JEEP SHAFT NOTE STOCK JEEP COLUMN The stock Jeep column shaft is a 7 8 diameter This column shaft is also hallow To properly secure the yoke to the column you will need to use the yoke as a template and drill one 5 16 ORIGINAL COLUMN CLAMP diameter hole 3 16 deep for the short set screw The second hole for the long set screw needs to be drilled with a 19 64 drill through one side of the column shaft This set screw is then installed through the yoke and one side of the column shaft tighten up on the opposite inside wall of the stock column Once both set screws are installed tighten the jam nut and locktite to secure dA SIM STEERNG AUN Custom columns offer several distinct advantages The advantages include locks tilts flashers and custom vehicle appearance However they do create some problems and require careful consideration when mounting them to the floorboard and universal joint connection Universal joints are available to match nearly every style steering column available The special spline size on some of the custom columns will require a new U joint We offer a wide selection of various sizes The new universal joint is supplied with a mating connection that will fit the new 3 4 DD steering shaft If a custom column is being used and you have already purchased the stock Jeep 7 8 diamet
10. T Routing the steering driveshaft may seem simple but care should be taken as to the actual routing On some Jeep installations it may be necessary to go directly through the motor mount Routes may be adjusted by changing the angle of the steering box slightly or by extending the universal yoke from the column bushing with a spacer Before any final route is decided be sure to allow for Suspension travel and engine movement On some conversions a third universal yoke might be considered along with a bearing pillow block Manifold clearance on Jeeps with a stock 225 V6 The steering shaft can have some exhaust clearance issues on some Jeeps One that was brought to our attention is the Jeep 225 V6 with a Sawinaw steering swap The steering shaft hits the stock manifold two options for clearance would be switch to exhaust headers for the Jeep or switch to a Buick 231 1975 and newer rear wheel drive vehicle manifold SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible warranty or return privileges If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your v
11. arranty or return privileges If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores ADVANCE ADAPTERS INC P N 716805 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 7 OF 10 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 08 05 10 MANUAL STEERING CONVERSION JEEP UNIVERSAL SAGINAW STEERNG BOX Power and Manual steering gear boxes are very similar We have already illustrated what the box should look like The steering box must be able to mount on the inside frame rail of your vehicle with the input shaft extending horizontally toward the firewall This input shaft is normally not long enough to extend fully into the engine compartment to couple with the steering driveshaft This is why we offer steering spud shafts to extend these steering input shafts The manual boxes have variable input shaft lengths The manual boxes that we recommend have an input shaft extending approximately three to four inches away from the main housing The manual steering boxes must be se
12. ble D as of 5 24 13 Due to limited supplies of the center socket tie rod end P N 716819 no longer is supplied in this kit JEEPSAGINAW STEERING INSTRUCTIONS Advance Adapters Inc has been manufacturing steering conversion parts for installation of the Saginaw steering boxes into Jeep vehicles for more than twenty years The parts we furnish are of the highest quality available and we utilize only proven design components for our kits Before you consider the conversion we recommend that you thoroughly read and understand the complete procedure Do not take short cuts on steering installations We recommend that these conversions be installed by a qualified technician Do not overlook any details Remember that the control of your vehicle depends on the steering gear performance Failure of your steering system can result in severe damage and possibly injury SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible warranty or return privileges If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams
13. cured with a minimum of three socket head cap screws with high collar lock washers The threads in the manual steering box must be drilled out for clearance of the 7 16 socket head cap screws so that the bolts can be installed through the steering box into the mounting plate TIE RODS Each of our kits include the necessary long amp short tie rods for your conversion The long tie rod connects the two front wheels while the other connects the Pitman arm to the passenger side steering knuckle center socket tie rod Both tie rods are manufactured with both a right amp left hand thread to assist in proper alignment The Pitman arm that we have furnished with your kit has exactly the same taper that the Jeep tie rod ends have Care should be taken for the proper fit of the tie rod end s taper and threads when installing into the Pitman arm In some cases it may be necessary to use two or three washers on the top side of the Pitman Arm so that the threads on the tie rod end will secure the proper taper fit All tie rod ends must be secured with a castle nut and cotter pin All tie rod to tie rod end connections must have a tie rod clamp installed with a bolt lock washer and nut We DO NOT find it acceptable to cut and weld the tie rods ATMAN ARVE The steering box Pitman arms vary from power to manual and are not interchangeable The Pitman arm supplied in each kit is for use on vehicles that are not equipped with a suspension lift If your vehic
14. ehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores ADVANCE ADAPTERS INC P N 7716805 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 6 OF 10 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 08 05 10 MANUAL STEERING CONVERSION JEEP UNIVERSAL FRONT CROSSIVEVERR The early Jeeps used a bell crank mounted on the front crossmember and this crossmember was originally located in the engine compartment If an engine swap has been performed we recommend installing a new crossmember located further forward directly in line with the front grill When installing the Saginaw conversion this new crossmember will require an access hole that is roughly 2 1 2 in diameter to provide clearance for the steering spud shaft clamp This access hole allows the steering spud shaft to extend through and into the engine compartment In most cases the front crossmember must be reinforced on both the top amp bottom because of the diameter of the access hole STEERNG BOX LOCATION The actual positioning of the steering box should be accomplished by bolting the box to the plate provided and then temporarily clamping the plate and box to the inner frame rail until an ideal position is achieved Make sure this position allows the steering spud shaft to extend through the front crossmember and into the engine
15. er column yoke you will then need to exchange your universal joint for the one that will be required on your installation We offer special yoke assemblies to connect a custom steering column to our Saginaw steering components P N 716848 1 48 spline Universal yoke GM columns P N 716849 1 DD x 3 4 DD Universal yoke GM and Ford P N 716850 3 4 x 36 spline Universal yoke GM and Ford The dimensions represent the column side of these yokes only The opposite side of these yokes is a 3 4 DD SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible warranty or return privileges If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores ADVANCE ADAPTERS INC P N 716805 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 5 OF 10 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 07 09 13 MANUAL STEERING CONVERSION JEEP UNIVERSAL STEERING S
16. er or axle and uses a push pull affect for steering Because there are many motions and joints on this system excessive free play and backlash develops il fa Stock Illustration tf pt bass 8 Stock with long tie rod The Saginaw steering system requires the elimination of the stock gear box and bellcrank The new steering box is mounted on the inside of the left front frame rail just behind the bumper Although this sounds simple there are several things that must be considered before the installation can be completed Such things include Power or manual steering Steering column type Steering box location Motor mount clearance on steering shaft Tie rod size amp length Winch clearance On engine conversions that are retaining the original steering box location you will be locating the engine position as close as possible to the original steering box When eliminating the original steering box you will be able to offset the new engine 1 towards the driver s side in order to allow for additional front driveshaft and starter motor clearance In 1971 Jeep changed their steering design to almost the exact same configuration as the kit that we offer The difference between the original Jeep installation and our installation is mainly in the design of the mounting bracket for the steering box Jeep also used a rag joint coupler between the steering box and steering shaft Saginaw Steering Installatio
17. ke in position onto the shaft and firmly up against the bushing Before tightening the set screw have someone push the steering wheel downward You will find that the column has a slight spring tension Make sure that the tension will provide a slight pressure of the universal yoke against the bushing We require the universal yoke installation to have a spot drilled inline with the set screw Failure to make each yoke installationas specified could result in the loss of control of the vehicle SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible warranty or return privileges If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores ADVANCE ADAPTERS INC P N 716805 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 4 OF 10 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 08 05 10 MANUAL STEERING CONVERSION JEEP UNIVERSAL DOUBLE SET SCREW WITH LOCTIT
18. le requires a dropped Pitman Arm then we suggest that you contact a suspension lift company We DO NOT find it acceptable to cut or bend our Pitman Arms POWER SHANG PUVBS There are only a few pumps available and most are interchangeable We recommend the purchase of the power steering pump and steering box as a pair if possible For proper installation we recommend the hose kits from PSC The hardware for mounting the pump to the engine can be standard parts from Chevy amp Ford engines TURNING ANGE AQ LEMENT To avoid damage to the outer axle U joints it is advisable that you check the turning angle The following is a list of the correct turning angles CJ2A CJ3A 23 Degrees CJ5 Up to Serial No 57548 48284 23 Degrees CJ3B Up to Serial No 57348 35326 23 Degrees CJ5 After Serial No 57548 48284 27 5 Degrees CJ3B After Serial No 57348 35326 27 5 Degrees CJ6 Up to Serial No 57748 12497 23 Degrees CJ6 After Serial No 57748 12497 27 5 Degrees To adjust the turning angle stops loosen the lock nut and turn the adjustment screw On some early models a secured weld will have to be broken The adjusting screw Is located on the axle tube near the knuckle housing For further detailed information refer to your vehicle service manual SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible warranty or return privi
19. leges If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores ADVANCE ADAPTERS INC P N 716805 P O Box 247 4320 Aerotech Center Way Paso Robles CA 93447 PAGE 8 OF 10 Telephone 800 350 2223 Fax 805 238 4201 Page Rev Date 08 05 10 MANUAL STEERING CONVERSION JEEP UNIVERSAL CSIR AQUSTIVENT The purpose of the caster adjustment is to provide steering stability which will keep the front wheels in a straight ahead position It also assists in straightening the wheels after making a turn If the angle of the caster is found to be incorrect correct it to the specifications given in your service manual The correct angle is obtained by installing caster shims between the axle pad and the springs If the camber and the toe in are correct and it is known that the axle is not twisted a check may be made by testing the vehicle on the road Before road testing make sure that the tires are properly inflated at the same pressure If the vehicle turns easy to either side but is hard to straighten out ins
20. n Ei MANLAL BOX SH_ECTION Make sure the box that you select has the same basic configuration as the ones illustrated Manual boxes can be found in the 1960s and early 1970 GM cars or Jeep vehicles 1972 amp newer The manual steering box must have a shaft stickout length of approximately 3 long and the spline on the shaft approximately 1 long The location of the Saginaw steering box will require a spud shaft This shaft couples and extends the steering box shaft into the engine compartment Manual boxes have two spline sizes that mate to our spud shaft Our manual steering kits are supplied with a 730 dia 30 spline spud shaft If steering box has 730 dia 36 spline Part No 716834 36 can be substituted Manual Steering Box SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible warranty or return privileges If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores
21. ons Modifications to any of the components will void any possible warranty or return privileges If you do not fully understand modifications or changes that will be required to complete your conversion we strongly recommend that you contact our sales department for more information This instruction sheet is only to be used for the assembly of Advance Adapter components We recommend that a service manual pertaining to your vehicle be obtained for specific torque values wiring diagrams and other related equipment These manuals are normally available at automotive dealerships and parts stores
22. ufficient caster for ease of handling is indicated If correction is necessary it can be accomplished by changing the shims between the spring and axle pads TCE IN AQLSTIVENT Lift the front of the vehicle to raise the front tires off of the ground Turn the wheels to the straight ahead position Using a pencil or chalk scribe a line in the center of each tire tread The mark should circle the entire diameter of the tire Measure the distance between the scribe lines at the front and rear of the wheels using care that both measurements are made at an equal distance from the floor level The distance between the lines should be greater at the rear then at the front by 3 64 to 3 32 To adjust loosen the clamp bolts and turn the long tie rod with a small pipe wrench The tie rod is threaded with right hand and left hand threads to provide equal adjustment at both wheels Do not overlook the retightening of the two clamp bolts It isacommon practice to measure between the wheel rims This is satisfactory providing the wheels run true By scribing a line on the tire thread a measurement is taken between the road contact points reducing error caused by wheel rim run out Itis recommended to have the alignment done by a qualified technician SPECIAL NOTE The components packaged in this kit have been assembled and machined for specific type of conversions Modifications to any of the components will void any possible warranty or return privileges If
Download Pdf Manuals
Related Search