Home

Super Alpine Racer Service Manual

1. Product Arcade Gaming System Models Alpine racer ATM for Report 101411488CHI 001 Page 1 of 1 ED 16 3 15 1 Jan 13 Mandatory To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Unpack Materials w N A ae Place the shipping crates on a flat stable surface Cut the banding straps and remove the cardboard lids Lift off the large cardboard containers surrounding the front pedestal and monitor assemblies and remove any shipping cleats Remove the coin door key from the coin return slot Open the top coin door Locate the keys for the back door and the cash box door Open the cash box door and remove the cash box Check for shipping damage to the following e Alpine Racer player accessible areas such as the ski platform and dash 6 Marquee and monitor e Cabinet decals Check the AC line cord for visible signs of damage Pay particular attention to the plug and line cord insulation Mechanical Setup READ THIS DOCUMENT AND BECOME FAMILIAR WITH THE SETUP REQUIREMENTS BEFORE YOU BEGIN WITH INSTALLATION IMPORTANT SAFETY NOTES Game Setup requires at minimum 2 individuals able to lift 5O pounds or more for safety Make sure that the work area suitable for installation and setup It must be well lit have a level surface and free of debris Adequate clearance is required around the unit for us
2. shown below to the models described in the Product s Covered section when made in accordance with the conditions set forth in the Certification Agreement and Listing Report This authorization also applies to multiple listee model s identified on the correlation page of the Listing Report This document is the property of Intertek Testing Services and is not transferable The certification mark s may be applied only at the location of the Party Authorized To Apply Mark Applicant Raw Thrills Inc Manufacturer Partec Inc W Belmont Avenue 9301 Fargo Avenue 5441 Address Skokie IL 60077 Padres Franklin Park IL 60131 Country USA Country USA Contact Mr Richmond Catalan Contact Mr Brian Poklacki Phone 847 679 8373 ext 28 Phone 847 678 9520 FAX 847 679 8538 FAX 847 678 1940 Email rich rawthrills com Email poklacki partec inc com Party Authorized To Apply Mark Same as Manufacturer Report Issuing Office Chicago IL godhon DAT Control Number 3174723 Authorized by for Thomas J Patterson Certification Manager Intertek This document supersedes all previous Authorizations to Mark for the noted Report Number This Authorization to Mark is for the exclusive use of Intertek s Client and is provided pursuant to the Certification agreement between Intertek and its Client Intertek s responsibility and liability are limited to the terms and conditions of the agreement Intertek assumes
3. 13 After 30 seconds turn cabinet power switch on 14 Game will reboot and enter calibration mode 15 Re calibrate controls Page 30 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL BIOS Settings Power Management NOTICE The PC ships with correct BIOS settings Making changes to the BIOS different from the description below may adversely affect game functions This BIOS setting lets the PC automatically power up With the setting enabled the PC reboots when it detects AC power This eliminates the need to manually turn the PC back on after power disruption Do not use the PC on off switch Turn AC power on or off with the cabinet power switch Turn cabinet power switch off Open rear of cabinet Connect a USB keyboard to the PC While holding the F10 key on the keyboard down turn cabinet power switch on ga ges When the BIOS menu screen appears make the following adjustments SETTINGS BELOW ARE SPECIFIC TO HP6005 PC PLEASE CHECK RAWTHRILLS COM FOR LATEST INFORMATION ON BIOS SETTINGS AND OTHER TECHNICAL UPDATES STORAGE gt Storage Options gt SATA Emulation Native Mode IDE ADVANCED gt Power On Options gt After Power Loss On 6 Follow instructions on screen to save and exit 7 PCwill reset and load the game Page 31 2014 NAMCO BANDAI Games I
4. CRUSHED 1 Monitor safety suspension chains have been installed to help support the monitor weight for this process Carefully use a T 27 tool to remove 2 sets of short bolts and washers holding the monitor mounting plates on each side of the monitor SEE ARROW A Once the bolts have been removed the monitor should be gently guided into its operating position BE CAREFUL NOT TO PLACE FINGERS IN A PLACE WHERE THEY MAY BECOME PINCHED OR CRUSHED After the monitor has been safely rotated back to its operating position remove 4 sets of long bolts from each side 2 holding the mounting plates in place SEE ARROW B and 2 more near the top side of mounting tubes and toward the front of cabinet SEE ARROW C DO NOT REMOVE THE SCREWS AT THE BACK SIDE OF THE TUBES Page 8 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL NOTE It is recommended to keep all monitor mounting screws finger tight until all 12 screws have been installed for alignment purposes Once aligned all screws should be securely tightened such that the split lock washers have been flattened 2 Reinstall monitor mounting brackets as shown in the below figure Using T 27 tool install 4 sets of long screws through the side plates and tubes first SEE ARROW D then install remaining 2 sets of short screws int
5. Game Audits Courses General 1 General 2 Courses Course Wins Places Skiers Gameplay Exit Game Audits EVEREST MATTERHORN KILIMAH JARO Courses Wins General 1 General 2 Courses Course Wins Gameplay Exit EVEREST MATTERHORN KILIMAN JARO 26 25 36 25 37 50 2014 NAMCO BANDAI Games Inc Page 22 To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Game Audits ist Place 2nd Place 3rd Place 4th Place 5th Place 6th Place 7th Place 8th Place General 1 General 2 Courses Course Wins Skiers Gameplay Exit Average Place Max Win Streak Hax Lose Streak Cur Win Streak Cur Lose Streak Race Autopilots Game Audits General 1 General 2 Courses Course Wins Places punki 1 qirli blndi Gameplay Exit Page 23 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Game Audits Gameplay General 1 Track 0 Gates Hit 759 General 2 Track 1 Gates Hit 1121 Courses Track 2 Gates Hit 1027 Course Wins Total Gates Hit 2907 Places Skiers Track O Tricks 444 Track 1 Tricks 650 Track 2 Tricks 751 Total Tricks 1845 Track 0 Score 280679 Track 1 Score 308012 Track 2 Score 232
6. Thread 1 5mm Pitch 30mm Length 9 600 01161 01 10 McMaster Carr Type 316 Stainless Steel Cup Point 92313A192 Set Screw 8 32 Thread 3 8 Length Super Alpine Racer RY Electric Brake Assy pX ITEM NO PART NUMBER DESCRIPTION 1 608 00173 01 Main Ski Bracket 2 600 01362 01 Spherical Bearing Oiles 80FL 20 3 McMaster Carr Black Steel Split Lock Washer M8 Screw Size 4 91169A200 14 8mm OD 1 9mm Thick McMaster Carr High Strength Uncoated Class 10 9 Steel Cap A 91310A533 Screw M8 Thread 1 25mm Pitch 20mm Length Right Step Tray Assembly PUER pL Ian Left Step Tray Assembly 7 McMaster Carr DIN 125 Zinc Plated Class 4 Steel Flat Washer 4 91166A320 M20 Screw Size 37mm OD 3mm Thick 08 600 01197 01 Link Connector Block 9 60001 215 01 Connector Block Bumper 10 McMaster Carr DIN 125 Zinc Plated Class 4 Steel Flat Washer 2 91166A290 M12 Screw Size 24mm OD 2 5mm Thick Zinc Plated Class 8 Steel Nylon Insert Locknut Up MS SIT M12 Thread 1 75mm Pitch 19mm Wide 12mm 2 90576A119 High 12 McMaster Carr Alloy 932 SAE 660 Bronze Flanged Sleeve Bearing 7815K18 for 3 8 Shaft Diameter 1 2 OD 1 4 Length 13 600 01198 01 Shoe Link 14 McMaster Carr Ultra Tough Oil Lube Bronze Thrust Bearing for 2 3750K2 3 8 Shaft Diameter 3 4 OD 1 16 Thick Alloy Steel Shoulder Screw 5 16 18 Thread 1 2 15 McMaster Carr Thread Length 3 8 Shoulder Diameter 3 8 2 91259A617 Shou
7. connect harness from cabinet to panel mount connector on pedestal Install 6 black tamper proof Torx machine screws 34 20 thread 34 length and 6 black split lock washers and 6 black flat washers through brackets and into PEM nuts on pedestal sides using T 27 tool 4 Locate 1 pole to cabinet bracket and the following hardware 4 black tamper proof Torx machine screws 14 20 thread 1 4 length and 4 black split lock washers and 4 4 black flat washers Using Page 12 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL T 27 tool install bracket over cross tube and attach to front panel of cabinet through slots into T nuts inside cabinet 5 Locate 1 black tamper proof Torx machine screw 4 20 thread 2 length and 1 zinc fender washer and 1 4 20 keps lock nut Open top coin door and attach the washer and keps nut on the interior of the cabinet to the long machine screw after it passes through the bracket the cross tube and front panel Use T 27 Tool and 7 16 socket wrench for tightening 6 Cabinet should have been leveled as the hardware was being installed and now all leg levelers can be lowered to the floor and all hardware securely tightened such that the split lock washers have been flattened Check Electrical Settings Verify the
8. no liability to any party other than to the Client in accordance with the agreement for any loss expense or damage occasioned by the use of this Authorization to Mark Only the Client is authorized to permit copying or distribution of this Authorization to Mark and then only in its entirety Use of Intertek s Certification mark is restricted to the conditions laid out in the agreement and in this Authorization to Mark Any further use of the Intertek name for the sale or advertisement of the tested material product or service must first be approved in writing by Intertek Initial Factory Assessments and Follow up Services are for the purpose of assuring appropriate usage of the Certification mark in accordance with the agreement they are not for the purposes of production quality control and do not relieve the Client of their obligations in this respect Intertek Testing Services NA Inc 545 East Algonquin Road Arlington Heights IL 60005 Telephone 800 345 3851 or 847 439 5667 Fax 312 283 1672 Standard for Safety for Amusement and Gaming Machines UL 22 Issued 2008 05 30 Ed 6 Rev 2013 09 25 Household and Similar Electrical Appliances Safety Part 2 82 Particular Requirements for Standard s Amusement Machines and Personal Service Machines CSA E60335 2 82 13 Issued 2013 01 03 used in conjunction with Household and Similar Electrical Appliances Safety Part 1 General Requirements CSA E60335 1 4E Issued 2003 04 01 R2007
9. proper voltage in the nearest AC outlet Verify the AC outlet ground connection is present and working 3 Referany issues with the AC outlet and service to qualified person Do not attempt to service or modify electrical outlets or line cords Game Power Up Plug in line cord to AC outlet Turn the power switch to ON Check that no component is excessively hot or emitting foul odors If not turn off AC power and disconnect line cord Refer to the diagnostic section of this manual 4 Once software loads you will be asked to calibrate the controls If not enter the service menu by pressing the TEST button located on the bracket inside the top coin door 5 Seemultiplayer networking linking information on page 24 25 Page 13 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Diagnostics and Adjustments The Service Button Panel has four buttons three of which can navigate the menu system But it is easiest to navigate with a Start Left Right Arrow buttons e Service Panel TEST enters diagnostic system e Either Service Panel TEST button or Start button selects the highlighted option 6 Service Panel VOL DOWN button or right arrow button moves down through menu or setting choices e Service Panel VOL UP button or pressing left arrow moves up through menu or setting choi
10. 814 Total Score 821565 Track 0 Airtime 7 04 22 Track 1 Airtime 22 48 Track 2 Airtime 29 38 Total Airtime 13 56 08 Track 0 Racetime 12 03 Track 1 Racetime 40 92 Track 2 Racetime uu Total Racetime 28 22 Pricing Adjustments Freeplay Please note the following r Money Unit Coin Value Adjusting the number of coins Coins Bill Pulse per credit will reset the Coins Credit stored number of partial Credits To Start credits Credits To Continue Hax Credits Bonus Credits Credits For Bonus ist Place Free Game 1st Human Free Game Page 24 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Freeplay No Yes No Money Unit USD Coins per Bill Pulse 1 Coins Per Credit Card Swipes USD AUD CAD EUR GBP DEM FRF JPY NLG ITL CHF DKK MXN RUR KRW CNY Credits To Start Credits To Continue Bonus Credits System Adjustments Attract Audin Change all system related Max Hame Length adjustments and settings here Blower Power Auto Volume Sync Hetwork Enabled Language QR Codes Game Venue Game Location Page 25 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Settings Defaults and Cho
11. Alloy Steel Pin in Torx Button Socket 96075A21 Cap Screw 1 4 20 Thread 1 2 Length High Hold Cone Point Type 316 Stainless GF qe ea Steel Set Screw 1 4 20 Thread 1 4 90778A401 E 600 01 179 0 Hand Grip Insert 600 01352 0 Hand Grip 10 600 01307 01 McMaster Carr Stainless Steel Pin in Torx Button Socket 2 91900A549 Cap Screw 1 4 20 Thread 2 Length 2 2 2 2 super Alpine Racer Ski Poles ITEM NO PART NUMBER DESCRIPTION 1 600 01189 01 Pot Bracket 2 301 00031 01 1K Potentiometer w Flat on Shaft 3 McMaster Carr Type 316 Stainless Steel Cup Point 92313A105 Set Screw 4 40 Thread 3 16 Long 4 600 00116 01 Small Drive Gear 5 600 01188 01 Idler Stud 18 8 Stainless Steel Truss Head Phillips McMaster Carr Machine Screw 10 32 Thread 3 8 2 91770A827 Length 7 600 01161 01 RY Super Alpine Racer pS Pot ana Gear Assembly ITEM NO PART NUMBER DESCRIPTION 1 600 01185 01 Rosta Plate 2 BARAT n UHMW Polyethylene Flat Washer 25649 A247 5 8 Screw Size 1 07 OD 06 Thick 38 e600 01298 01 Rosta DR S 18x80 lt Super Alpine Racer Rosta and Plate Assy 2 0019501 smal Broke Bushing 1 3 4 600081660 Broke Bracket Assembly 1 7 McMaster Carr Zinc Plated Steel Flat Washer M10 0 Screw Size 30mm OD 2 5mm Thick Black Class 12 9 Alloy Steel Socket pO Head Cap Screw M10
12. CO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Electrical Power Shipping Dimensions United States International and Japan Main Cabinet 42 x 37 x 86 1 06m x 1 19m x 2 18m Inrush AC Current 7 Amps Pedestal 42 x 38 x 55 1 06m x 97m x 1 40m Operating AC Current 5 Amps Weight 650 Ibs 294 84 kg Voltage 100 115 240 50 60Hz VAC Temperature 50 F to 104 F 10 C to 40 C Humidity Must not exceed 9596 relative humidity Dimensions Height 102 4 2 60 meters Width 35 3 90 meters Depth 79 3 2 01 meters C US LisTED Intertek Electrical Safety Notice This product is designed for indoor use only For continued electrical safety replace fuse with fuse of equivalent rating Use only properly grounded AC service outlet and correct line cord Do not by pass the ground terminal or use cheater plug Doing so would create an electrical hazard and also affect the games safety and reliability due to increased Electro Static Discharge susceptibility Do not install game near source of water jet or condensation Page 5 2014 NAMCO BANDA Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 Intertek AUTHORIZATION TO MARK This authorizes the application of the Certification Mark s
13. Enter the Coin Meter Test menu and verify the operation of the coin meter Enter the Cabinet Lamps Test menu and verify that all cabinet lights work correctly Enter the Watchdog Test menu which reboots the game P rl m ru Upon a successful reboot you are ready to make adjustments to pricing volume and other functions found in the Adjustments Audits and Diagnostics section Page 15 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Test Main Menu Diagnostics Game Audits Pricing Adjustments System Adjustments Game Adjustments Utilities Calibration Volume Attract Volume Exit Verify all game functionality Allows activation of all inputs and Diagnostics S outputs including linking and watchdog test Game Audits View game earnings and gameplay statistics Pricing Adjustments Setting for coinage unit denomination and game pricing System related changes such as networking language attract volume Wheel power blower and shaker force etc System Adjustments Game Adjustments Game specific adjustments such as difficulty bonus time game entry Clear Credits Audits and reset player game statistics Check system software errors and download data to USB external storage device Utilities Calibration Calibrate controls for maximum player control and game exper
14. IAGRAM a ITEM NO PART NUMBER DESCRIPTION Alpine Front Cab Super Alpine Racer Front Cabinet _ASSY Assembly 2 Alpine LCD Cov Super Alpine Racer Monitor Back er Assy Cover Assembly 3 McMaster Carr Black 18 8 Stainless Steel Flat Washer 96765A125 10 Screw Size 7 16 OD 03 Thick 4 McMoster Carr Black Steel Split Lock Washer M5 Screw 91169A170 Size 9 2mm OD 1 1mm Thick Black Alloy Steel Pin In Torx Button 5 McMosterCarr socket Cap Screw 10 32 Thread 1 2 96075A187 Length Alpine Marquee Super Alpine Racer Marquee ASSy Assembly 7 McMoster Carr Black Steel Split Lock Washer M8 Screw 34 91169 A200 Size 14 8mm OD 1 9mm Thick Black Alloy Steel Pin In Torx Button McMaster Carr socket Cap Screw 1 4 20 Thread 1 2 96075A21 Length Platform to Cabinet Connecting 10 McMaster Carr Black Steel Flat Washer 1 4 Screw Size 30 96765A 140 5 8 OD 04 Thick Black Alloy Steel Pin In Torx Button S 0 Socket Cap Screw 1 4 20 Thread 1 12 1 2 Length Black Alloy Steel Pin in Torx Button 12 McMaster Car socket Cap Screw 1 4 20 Thread 3 4 96075A219 Length 13 600 01350 01 Pole to Cabinet Bracket Stainless Steel Pin in Torx Button Socket McMaster Carr i i EM 500A 549 BLACK CaP Screw 1 420 Thread 2 Length Paint Black Black Alloy Steel Button Head Socket 15 McMaster Carr Cap Screw 1 4 20 Thread 2 1 2 91255A547 Length Zinc Plated Steel Large Diameter Flat 16 McMast
15. LL VALIDATOR ds COIL GND 5 S EE V SIG o a oo Lie SIGNAL 5V4 1 YEL GRN MOTOR SIGNAL e ORG RED 9 MOTOR V FUSED AR C COIN 1 80 ES CUN S 2 e ToL BLU imis COIN r gt SIN ro OR SKI BRAKE LOCK m DLILIR 500 00075 00 TEST 0 6 BLK BRAKE GND 12 VOL y BLK WHT 2 BRAKE 17 vit 0 0 YELX BRAKE SERVICE 15 0 6 BRAKE 16 9 mm JEDE y 17 BRN YEL 58 EC EU 118 COIN_MTR SIGNAL 5V P4 5 YEL BL PU BRAKE SIGNAL 2 COIN DOOR FIELD GND ee DRO Vr Sime L en y a MFIT JR 39 01 2120 BLK GND WHT 0 0 LFT ARROW WHT BRN 9 0 START SELECT BLOWER 18AWG 0 0 RGT ARROW YELX VID RED 0 LFT ARROW LMP po VID ORG START SELECT LMP BLK GRN JVI BRN RGT ARROW 3 AAA TAN 5vdc P RED 5V 9 WHT_RED STEER 1 BK y uio A Ea 1 3 ul S STEERING 5K 5 BRN RED 2 BRN BLK Sl meDYEL BRN YE 8 i P9 EDGE 16 SKI BRAKE 18AWG YELX 1 BLK GRN E L 3 4 SKI BRAKE 8 10 BLUE LED 5 12V PWM MARQUEE ISH YEE RED YEL RED ver aek eer oe RED LED H YEL_BRN 0 SLL Ye GRY L vosu e MLILD L R Tel veL RG 3 ORG YEL 12V PWM i VEL VID YEL RED 4 GRY SIL VE YE ac RED LED 55 YEL GRN d sue cep CIL PNL 24 ORG YEL v PWM 6 P7 BLK BLUE LED ORG YER Y O o 12V PWM SKI RED LED O ES E EE PLATFORM BLU LED ALPINE SKI SYSTEM D
16. MBER DESCRIPTION 1 600 01336 0 RIO Mounting Plate w Blower PCBs 2 500 00040 01 RIO PCB 3 500 00075 02 Snow Blower PCB 4 McMaster Carr 18 8 Stainless Steel Hex Washer Head Slotted 14 90316A190 Machine Screw 8 32 Thread 1 4 Length NS RIO Assembly with Mounting Plate ANS 2 1 18 00 00 000 Goldwood 8 Woofer 4 Ohm Poly Mica Cone 1 3 McMaster Carr Zinc Plated Steel Slotted Hex Washer Head 4 90054A 196 Screw 8 Size 5 8 Length 4 Wire Mesh Gril 7 25 7 25 super Alpine Racer Woofer Mounting Assembly NOT DISPLAYED 1 603 00718 01 LED T Molding 63 125 1 500 00131 01 RGB LED Strip 160 CM DESCRIPTION Blower Bracket Johnson Blower Foam Fifer Bao 5 McMaster Carr 18 8 Stainless Steel Hex Washer Head Slotted 4 90316A196 Machine Screw 8 32 Thread 5 8 Length McMaster Carr Zinc Plated Steel Split Lock Washer 8 Screw 4 91102A735 Size 0 3 OD 04 Thick 7 McMaster Carr Zinc Plated Steel Flat Washer 8 Screw Size 4 90126A512 7 16 OD 05 Thick Super Alpine Racer Blower Assembly ITEM NO PART NUMBER DESCRIPTION 601 00658 01 Control Panel Wood g Happ Large Round Green Pushbutton with Locking 2 702 00098 01 Lampholder 6VDC White LED 187 Gold MS START Happ Large Round White Pushbutton with Locking 3 02 00057 01 Lampholder 6VDC White LED 187 Gold MS ARROW McMaster Carr Zinc Plated Steel Flat
17. To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 2 BANDAI e AM NAMCO Games OPERATOR S MANUAL VERSION 0 1 PRELIMINARY 2014 NAMCO BANDAI Games Inc MARCH 20 2014 40 00037 01 To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL ANNY Uses Granny Animation Copyright C 1999 2014 by RAD Game Tools Inc Uses Bink Video Copyright C 1997 2014 by RAD Game Tools Inc Page 2 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL OPERATION Before operating game read this manual Failure to properly install and operate this game could result in malfunction or accident Operate the game in accordance with the manual TRANSPORTING The cabinet is very heavy Because the monitor is high the cabinet is also very top heavy Use appropriate care when moving or transporting cabinet It contains fragile glass and electronic components Avoid rough handling HANDLING COMPONENTS Many components are extremely sensitive to handling environmental and Electrostatic Discharge ESD events especially the computer Do not handle it roughly Before servicing call your distributor and inquire a
18. Washer 8 Screw Size 7 16 OD 90126A512 05 Thick 7 McMaster Carr Zinc Plated Grade 2 Steel Nylon Insert Hex Locknut 8 2 90631A009 32 Thread 11 32 Width 15 64 Height McMaster Carr 18 8 Stainless Steel Pin In Torx Button Head Sheet Metal 2 95638A194 BLACK Screw 8 Size 1 2 Long Paint Black 600 01355 01 Control Panel T Molding Plate 4 600 01340 01 Blower Grill 5 McMaster Carr Black Alloy Steel Pin in Torx Button Socket Cap Screw 2 96075A147 8 32 Thread 1 Length ITEM NO PART NUMBER DESCRIPTION 1l 608 00181 01 oo Monitor Frame Front Bezel Weldment Monitor Foam Tape 2 47 25 Black 5 8 W x 1 8 Tx 47 1 4 L 2 Monitor_Foam_Tape 5 i 30 75 Black 5 8 W x 1 8 Tx 37 3 4 L 4 809 00012 01 Kortek 55 LCD Open Panel w Glass 5 600 01331 01 55 Kortek Retainer Bracket Zinc Plated Steel Machine Screw Nut with Moe 0 Tooth Washer 10 32 Thread 3 8 Width 1 8 Height 7 600 01332 01 55 Kortek Back Plate McMaster Carr Black Alloy Steel Pin in Torx Button Socket 18 96075A183 Cap Screw 10 32 Thread 3 8 Length 9 600 1 365 01 Monitor Hinge Bracket McMaster Carr Zinc Plated Grade 5 Steel Cap Screw 1 4 4 92865A535 20 Thread 3 8 Length 7 7 m super Alpine Racer Monitor Enclosure Assembly R ITEM NO PART NUMBER DESCRIPTION 600 01333 0 oo Monitor Cover Box 800 00001 00 120mm Wire Fan Guard ME NE M 3 820 0012 00 Cooling Fan st
19. age 10 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL STEP 3 PEDESTAL INSTALLATION PROCEDURE NOTE It is recommended to keep all pedestal mounting screws finger tight until all screws have been installed for alignment and leveling purposes Once aligned all screws should be securely tightened such that the split lock washers have been flattened 1 To ease the leveling process of the pedestal the middle leg levelers SEE ARROWS should be raised such that only the 4 corner leg levelers are in contact with the floor as shown in the above figure 5 8 and 3 4 open end wrenches for the locking hex nut and leg leveler nut respectively will be needed to adjust pedestal leg levelers as brackets are being installed Page 11 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL 2 Locate 2 platform to cabinet connecting brackets and the following hardware 8 black tamper proof Torx machine screws 14 20 thread 1 4 length and 8 black split lock washers and 8 black flat washers Using a T 27 tool attach these brackets to each side of cabinet as shown in figure above 3 Move pedestal in place between these brackets and
20. ame Entry After Race Girls and Crowds Enable Girl Video Enable Girl Racer Crowd Autopilot Available Page 27 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Reset Audits Reset High Scores Reset Player Stats Reset Adjustments Reset Link System Factory Restore View Errors View Messages Copy Audits and Logs Copy High Scores CRC Check Calibration Page 28 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Game Volume Adjust game volume during play mode only Attract volume is adjusted separately Automatic Volume Sync allows for all linked units to be adjusted simultaneously Attract Volume Adjust attract or standby volume only Page 29 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Hard Drive Recovery Symptoms requiring hard drive recovery include 6 File Test reports bad or missing files e Game fails to finish loading during startup e After resetting the AC power an error is reported e You are prompted to insert a boot DVD e Erratic Game or Att
21. andard size 12VDC 3W 80CFM EN 4 McMaster Carr Zinc Plated Steel Flat Washer 6 Screw Size 3 8 4 90126A509 OD 05 Thick 0 McMaster Carr Zinc Plated Grade 2 Steel Nylon Insert Hex 4 90631A007 Locknut 6 32 Thread 5 16 Width 11 64 Height 7 Super Alpine Racer Monitor Back Cover Assembly pS Sw ITEM NO PART NUMBER DESCRIPTION 400018580 2 0000 62 01 75cm White har M roam Backing 3 600 00998 01 3 8 Spacer Em 4 606 00929 01 Marquee Translite 5 600 01360 01 Marquee PETG Plastic McMaster Carr Black Alloy Steel Pin in Torx Button Socket 96075A19 1 Cap Screw 10 32 Thread 3 4 Length 7 600 01359 01 Marquee Mounting Bracket McMaster Carr Black Alloy Steel Pin In Torx Button Socket 4 96075A21 Cap Screw 1 4 20 Thread 1 2 Length McMaster Carr Black Steel Split Lock Washer M8 Screw 4 91169 0 Size 14 8mm OD 1 9mm Thick 4 10 McMaster Carr Black Steel Flat Washer 1 4 Screw Size 96765A140 5 8 OD 04 Thick lt Sw Super Alpine Racer Marquee Assembly Mss ITEM NO PART NUMBER DESCRIPTION Alpine Main Pedestal Sub Super Alpine Racer Main _ASSY Pedestal Sub Assembly 2 Pedestal Leg Leveler 1 2 13 Thread 4 Length 8 Alpine Pot Assy Super Bas cu and EN Zinc Plated Grade 2 Steel Nylon EM con Insert Hex Locknut 10 32 Thread 3 8 Width 15 64 Height 5 ipine Electric Broke Assy Super Alpine Electric Brake Zinc Plated Gra
22. bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Light Test For troubleshooting purposes this menu allows the diagnosis of the game s controlled lighting features Toggle All Toggle Marquee Toggle Buttons Toggle Panel E Toggle Panel Toggle Panel B Toggle TMolding E Toggle TMolding Toggle THoldinq E Toggle Ski Toggle Platform Exit Coin Meter Test For troubleshooting purposes this menu allows the activation of coin meter Press Start or Test to advance coin meter Watchdog Test This menu allows the activation of the watchdog reset system Press Start or Test to start test The game s watchdog system allows the machine to recover automatically from a crash or a failure to boot The watchdog system is always active Page 19 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Diagnostics Link System Test This allows the operator to view and reset the link status of two or more games connected to a single network Linking three or more games requires a network hub and must be purchased separately Status Reliability Test Link system is enabled Show All Machine IDs My machine ID 3 Restart Link System Total machines linked 1 Address 192 168 1 207 Reset Link System Confi
23. bout the PC warranty Use proper ESD procedures when servicing Protect components from harmful environmental conditions such as extreme temperatures excessive moisture or other damaging effects DISCONNECT POWER Always turn the power off and unplug the unit before servicing or making adjustments unless otherwise instructed Installing or repairing components while power is on can damage the components and void the warranty GROUNDING Avoid electrical shock Do not plug in AC power until you have inspected and properly grounded the unit Only plug into a grounded three wire outlet Do not use a cheater plug or cut off the ground pin on the line cord ELECTRICAL SHOCKS There is no isolation transformer in the cabinet Disconnect AC power before servicing However be aware that lethal voltages can remain in the electronic components even when AC power is disconnected Use extreme caution when servicing Verify that there is a working ground connection If the unit sustains water damage cease using it immediately and unplug AC power MONITOR The monitor contains no user serviceable parts Do not attempt to service the monitor POWER SELECTOR Before installing game ensure the voltage on the PC and power supply are set properly There is a 115 230 VAC selector switch that must be set for the correct voltage for your site Verify the fluorescent lamp rating The rating must match the line voltage at the installation site POWER CORD If t
24. ces e Highlight and select Exit to return to previous screen An on screen message acknowledges changes or when you exit a selection without making a change At the bottom of each screen there is a brief description of the menu option s function A complete description is available here for all menu functions Instructions for completing your first calibration start on the next page Page 14 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL GAME CONTROLS CALIBRATION 1 If the calibration screen is not visible press the TEST button to enter the Diagnostic System 2 From the Main Menu use Volume to highlight Calibration 3 Press a Start button to enter calibration Follow on screen instructions Re try if calibration data is not valid Game will proceed to Location and Venue Name entry Enter information to be displayed when player scans the QR Code Game will enter Attract Mode All game settings will be default values if no changes are made at this time GAME CONTROLS AND INTERFACE INSPECTION Qu E s Other Tests See the Diagnostic Section for further information Enter the Switch Test menu and verify all switches function Enter the Screen Test menu and verify that video is acceptable Enter the Sound Test menu and verify the audio works and is not distorted
25. de 2 Steel Nylon DD Insert Heavy Hex Locknut 1 4 20 Thread 1 2 Wide 3 8 High DIN 125 Zinc Plated Class 4 Steel 7 ANE ean aad Flat Washer M12 Screw Size 24mm OD 2 3mm Thick Metric Zinc Plated Class 8 Steel ara Hex Nut M12 Thread 1 75mm Pitch 19mm Wide 10mm High 9 Alpine Rosta Plate Assy Super Alpine Racer Rosta amp Plate ASSY Black Alloy Steel Class 12 9 Socket 10 PEE e Head Cap Screw M6 Thread 25mm Length Imm Pitch M Alpine Platform Assy Super Platform 13 Black Steel Internal Tooth Lock PODES Washer MIO Screw Size 18mm OD 0 9mm Thick Black Class 12 9 Alloy Steel Socket Sh qi fe Head Cap Screw M10 Thread 1 5mm Pitch 20mm Length 600 01119 01 Rear Pedestal Cover 15 600 01120 01 Front Pedestal Cover Black Alloy Steel Pin in Torx Button 16 BLU Socket Cap Screw 1 4 20 Thread 8 1 2 Length McMaster Carr Black Steel Flat Washer 1 4 Screw 18 96765A 140 Size 5 8 OD 04 Thick 18 600 01203 01 Ski Front Cover Low Profile Class 8 8 Steel Socket 19 DE 0 Head Cap Screw M6 Thread 1mm Pitch 12mm Length 20 600 01208 01 Front Metal Cover Black Alloy Steel Pin In Torx Button 2 a e Socket Cap Screw 10 32 Thread 4 1 2 Length 5 Super Alpine Racer Pedestal Assembly Mss ITEM NO PART NUMBER DESCRIPTION 608 001 66 01 Pedestal Frame Assembly IA Super Alpine Racer Leg Leveler Assembly Super Alpine Racer Pedestal Cast
26. e of ladders Adequate clearance is required above the unit for bringing the unit to a full upright and operating position Do not lean on the game during installation Certain portions of the game may shift or move Keep your hands and fingers clear of moving parts at all times Exercise caution at all times throughout the installation process Make sure that all fasteners are installed where indicated Use the correct tools and fasteners Make sure each assembly is fully fastened and secure after each step Page 6 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL STEP 1 MARQUEE INSTALLATION PROCEDURE Locate the marquee assembly and the following hardware 4 black tamper proof Torx machine screws 20 thread length and 4 black split lock washers With the use of a ladder on a stable floor lift the marquee into position as shown and secure the 4 screws and washers using a T 27 Torx tool Page 7 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL STEP 2 MONITOR INSTALLATION PROCEDURE WARNING MONITOR IS HEAVY AND MOUNTED ON A HINGE BE CAREFUL NOT TO PLACE FINGERS IN A PLACE WHERE THEY MAY BECOME PINCHED OR
27. er Carr Washer 1 4 Screw Size 1 OD 05 91090A 108 Thick 17 Zinc Plated Steel Machine Screw Nut MOSS Car with Tooth Washer 1 4 20 Thread 7 16 Width 3 16 Height 3 eov Super Alpine Racer Pedestal Assembly S Super Alpine Racer 55 Assembly ss NOT DISPLAYED 810 00053 01 Service Bracket 800 00040 00 Solid State Relay 24V Power Supply Load Resistor and Bracket 603 00718 01 LED T Molding 65 5 500 00131 01 RGB LED Strips 165 CM 2 2 2 Monitor Safety Suspension Chains Super Alpine Racer Front Cabinet Assembly ITEM NO PART NUMBER DESCRIPTION 601 00651 01 Alpine 55 LCD Cabinet 2 e 0 RIO Assembly with Mounting Plate 3 2 1 02 00 00 017 APS Power Supply Bracket 90 AP 188 4 800 00001 00 120mm Wire Fan Guard 5 820 0001 2 00 Cooling Fan standard size 12VDC 3W 80CFM 6 HP6005 or approved equivalent PC 7 600 00901 01 Bracket PC Strap Mounting McMaster Carr PC Mounting Nylon Strip 0 075 Thick 1 Width 2 87425K76 Black 56 Length McMaster Carr Plastic Buckle for Webbing NO Sew Squeeze 2 29 05T86 Release for 1 Wide Webbing 10 601 00580 01 PC Wood Cleat Super Alpine Racer Woofer Mounting 1 Alpine Woofer Assy Assembly 18 Alpine 55 LCD Assy Super Alpine Enclosure 0 Standard Door Lock Assembly for 3 4 Panels 19 20 21 22 23 24 25 ITEM NO PART NU
28. ers 600 01348 01 Stop Pad 600 01 349 01 Stop Pad Holder Bracket McMaster Carr Zinc Plated Alloy Steel Socket Head Cap 90128A241 Screw 1 4 20 Thread 3 8 Length Alpine Pedestal Light Super Alpine Racer Pedestal Light _ASSY Assembly McMaster Carr Black Alloy Steel Pin in Torx Button Socket 96075A139 Cap Screw 8 32 Thread 1 2 Length Alpine Main Mech A Super Alpine Racer Platform Mechanism SSy Assembly McMaster Carr Black Alloy Steel Socket Head Cap Screw 91251A621 8 16 Thread 5 8 Length McMaster Carr Zinc Plated Steel Type A USS Flat Washer 90108A417 3 8 Screw Size 1 OD 06 Thick Alpine Ski Pole Assy Super Alpine Racer Ski Poles ee ea ic Black Alloy Steel Pin in Torx Button Socket 625in Cap Screw 1 4 20 Thread 5 8 Length McMaster Carr Black Steel Flat Washer 1 4 Screw Size 2 96765A 140 5 8 OD 04 Thick 4 2 2 2 2 3 4 5 10 11 12 13 4 EN Super Alpine Racer Main Pedestal Sub Assembly RS ITEM NO PART NUMBER DESCRIPTION QTY 600 01351 01 Leg Leveler Bracket 2 Pedestal Leg Leveler 1 2 13 Thread 4 Length McMaster Carr Grade 8 Steel Cap Screw 1 4 20 4 92620A539 Thread 5 8 Length McMaster Carr Steel Split Lock Washer 1 4 Screw 4 91101A229 Size 49 OD 06 Thick NX super Alpine Racer Leg Leveler Assembly am ITEM NO PART NUMBER DESCRIPTION 1 Pedestal Caster 2 Wheel 2 7 16 Mounting Height 2 McMaster Carr G
29. g Perform Restart Link System if A this information appears stale Exit Diagnostics Blower Test Test the blower function at different speeds This can also be used to determine desired blower instensity Page 20 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Game Audits General Audits 1 View general game statistics General 1 Time Since Boot 3 28 75 General 2 Time Game On 8 34 5 82 Courses Time Game Played 6 06 13 40 Course Wins Time Per Game 2 13 17 Places Skiers Games Played 165 Gameplay Games Started 131 Games Continued 9 Exit Games Timed Out 0 Free Games Link Games 0 an Boot Ups Test Mode Entries Maintenance Reboots Watchdog Resets Ho I O Board Init Untinished Games 0 0 I O Lost I O Recovered Dongle Lost Dongle Recovered Prefs Damaged Prefs Repaired ecoocr General Audits 2 General 1 First Person Time General 2 Dynamic Cam Time Courses Course Wins Places Skiers Total Coindrops Slot O Left Slot 1 Right Slot 2 DBV Gameplay Bonus Credits Exit Current Credits Current Coins Page 21 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL
30. he power cord is damaged or lost replace it with an identical cord as supplied by the manufacturer or an authorized service agent SURGE SUPRESSOR It is recommended that you plug your game s power cord into a surge suppressor to help protect from power surges that may damage sensitive electronic components Page 3 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Service Manual CONNECTORS When servicing machine ensure all connectors mate properly If connectors do not slip in easily do not force them Connectors are often keyed and only connect one way Check for correct orientation COMPUTER The computer contains sensitive components including a hard drive Do not handle it roughly Call your distributor before servicing its internal components Ask about warranty information as it relates to the PC Do not turn the PC power switch on or off It should remain permanently in the ON position Cycle AC power on or off with the cabinet power switch A dongle has been inserted into one of the USB ports This is required for game play Do not remove the dongle except for troubleshooting purposes FLUORESCENT LAMP A dropped fluorescent lamp tube may break and implode Shattered glass from the implosion can travel long distances and cause bodily injury Use proper procedures when handling br
31. herical Bearing Oiles 80FL 20 3 McMaster Carr High Strength Uncoated Class 10 9 Steel Cap 4 91310A533 Screw M8 Thread 1 25mm Pitch 20mm Length 4 McMaster Carr Black PIRE Pus Lock Washer M8 Screw Size 91169 A200 4 8mm OD 1 9mm Thick 5 600 01214 01 Mounting Bracket B 600 01213 01 Rosta Mounting Bracket A McMaster Carr Low Profile Class 8 8 Steel Socket Head Cap 93070A143 Screw M6 Thread Imm Pitch 12mm Length IN DE IN Y Super Alpine Racer ski Rosta Mounts Super Alpine Racer ES Platform Light Assembly pS ITEM NO PART NUMBER DESCRIPTION 1 600 01200 01 Pot Holder Bracket 2 301 00016 00 5K Potentiometer w Flat on Shaft Super Alpine Racer Ski Pot Assembly NOTES SUPER ALPINE RACER 2014 NAMCO BANDAI Games Inc
32. ices Network Enabled Yes No Must set each unit ID and enable link separately NOTE ON LINKING Linking three or more games requires a network hub and appropriate number of network patch cables These items must be purchased separately Follow the network hubs hookup instructions Use the crossover network cable provided with the game for linking 2 games Network settings must be set for each linked unit Up to 8 units can be linked Press Test button to access the game settings and diagnostics menu Linking 2 or more Games 1 Set Network Enabled to YES under System Adjustments 2 Set a unique Unit ID for each unit 3 The new settings will be automatically saved when exiting Test Menu 4 Verify successful network link by playing a test game Page 26 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Game Adjustments Game Difficulty Change all game related Start Time adjustments and settings here Checkpoint Time Speed Measurements To set Machine ID select Plays For Reset the Hetwork Enabled option Autopilot Hame Entry Girls amp Crowds Settings Defaults and Choices Game Difficulty Start Time Bonus 80 30 120seconds 0 00000 Checkpoint Bonus Speed Measurements Plays For Score Reset N
33. ience Page 16 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Set volume during game only Attract volume is adjusted independently Attract Volume Set attract standby mode volume only Diagnostics Switch Test For troubleshooting purposes this menu gives you visual feedback of all switch functions Switch Test Version Mar 4 2014 8 11 22 59 Input Device Hold Start Test To Toggle Brake Hold Service To Ext NOTE PRESS AND HOLD START BUTTON OR TEST BUTTON TO TOGGLE SKI BRAKE ON OFF Page 17 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL Sound Test For troubleshooting purposes this menu gives game sound feedback Change Effect Change sound current sound effect Play 100Hz or 1kHz Play low and high frequency to stimulate bass or full range speaker response Pan Center Left l l l Right Isolate sound into separate channel to verify correct speaker function Monitor Test For troubleshooting purposes this menu allows the diagnosis of the display to detect color or linearity issues Page 18 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www
34. lder Length 9 16 Head Diameter 1 4 Head Height 16 Alpine Rear Platform Super Alpine Racer Rear Platform Cover Cover Assy Assembly McMaster Carr Black Alloy Steel Pin In Torx Button Socket Cap 4 96075A187 Screw 10 32 Thread 1 2 Length EN dd Super Alpine Racer Ski Rosta Mounts 19 600 01299 01 Rosta DR S 18x30 20 Ski Pot Assy Super Alpine Racer Ski Pot Assembly 2 McMaster Carr Black Class 12 9 Alloy Steel Socket Head Cap 4 91290A418 Screw M8 Thread 1 25 Pitch 16mm Length 29 McMaster Carr Alloy Steel Nonmarring Flat Point Socket Set 93245A110 Screw M4 Thread 0 7mm Pitch 4mm Length 23 McMaster Carr Zinc Plated Steel Pan Head Phillips Machine 90272A826 Screw 10 32 Thread 5 16 Length wh Super Alpine Racer Platform Assembly bia 1 j amp ooeo RearMetalCower 2 400i3S0 Reaper 2 3 6000131601 RearBumper AnchorPlate 2 McMaster Carr Black Alloy Steel Pin In Torx Button Socket 96075A187 Cap Screw 10 32 Thread 1 2 Length 5 Alpine Platform Light Super ARINE sem Platform Light _ASSY Assembly McMaster Carr Black Alloy Steel Pin in Torx Button A 96075A139 Cap Screw 8 32 Thread 1 2 Length ITEM NO PART NUMBER DESCRIPTION 1 603 00543 01 5 Hole Tread Plastic 2 500 00169 01 24CM Red LED Great Wall Rope 4 Super Alpine Racer XS Rear Platform Cover Assembly zum NO PART NUMBER DESCRIPTION 1 600 01196 01 Ski Bracket Cap 2 600 01362 01 Sp
35. nc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL MECHANICAL ILLUSTRATIONS AND ELECTRICAL SYSTEM DIAGRAM VISIT WWW RAWTHRILLS COM FOR THE LATEST INFORMATION REGARDING SUPER ALPINE RACER Page 32 2014 NAMCO BANDAI Games Inc ORG BLK CABINET COOLING FAN AUDIO OUT DESI TOUP mel Oe DN RI O VIDEO QUT BLK YEL LCD DISPLAY HAPP P N 80 0074 00 lev T BETSUN P N UP 200PST CE ND SD Lacu ES RESISTOR 5V LOAD INLET 5v RED WHT ia PA ee PDWER SUPPLY me ser EH v PC AC POWER V 3 ACV PC WATCHDOG RELAY MAGNECRAF T PN 6210AXXSZS DC3 gt pr m G C N a A m lt LU 3 Fd je red Sj edo v CO m AREE Do 12V FUSED 12V FUSED oV FUSED GND GND 12V FUSED 12V FUSED oV FUSED GND GND 12V AUDIO IN GND AUDIO GND DIG GND DIG GND DIG SV IN SV STBY 12V IN GND DIG GND PC GND PC SV STBY SW PC PWR ON OlP11 USB B oM START NOS START SELECT 1e V PWM PWM GND LFT ARRDW RGT ARROW START1 LMP TM LFT RED LFT ARROW LMP RT ARROW LMP SKI RED LED TM LFT GRN TM LFT BLU STEER ca gt Y D SV D GND SKI BRAKE SPARE S SKI BRAKE SPARELZ YEL GRN BLOWER MTR TM BLU PLATFORM BLU BLOWER MOTOR DRV 300 00075 00 MOTOR GND MOTOR gt 12 VDC BI
36. o matching holes on monitor sides SEE ARROW E 3 Retrieve marquee harness at top right when viewing cabinet from back side and guide the harness down the right tube Connect the 3 position mating connector to the marquee harness at the back of the game near the I O pcb 4 Retrieve line cord from the right tube access hole when viewing cabinet from rear and make connection to monitor power port Retrieve video cable from the left tube access hole when viewing cabinet from rear and make connection to monitor video port Page 9 2014 NAMCO BANDAI Games Inc To Purchase This Item Visit BMI Worldwide at www bmigaming com Global Sales 561 391 7200 USA CA 1 800 746 2255 SUPER ALPINE RACER OPERATOR S MANUAL AMA C K AN AWAY 5 Locate the LCD cover plate assembly and the following hardware 8 black tamper proof Torx machine screws 10 32 thread length and 8 10 black split lock washers and 8 10 black flat washers 6 Retrieve fan harness from the left tube access hole when viewing cabinet from rear and make secure connection to exhaust fan on cover plate Also make sure the monitor line cord and video cable are not an obstruction to proper installation of cover plate 7 Using T 25 tool install cover plate assembly to the rear of the monitor box with the supplied hardware as shown in figure above NOTE PROPER ORIENTATION OF COVER PLATE AND ATTACHED FAN IS CRITICAL TO LIFESPAN OF MONITOR P
37. oken materials as these items can contain hazardous material such as mercury or lead HAZARD TO EPILEPTICS A small portion of the population has an epileptic condition that may cause seizures Affected persons experience seizure while watching some television pictures or playing certain video games People who have not had seizures may still have an undetected epileptic condition If anyone in your family has experienced epilepsy symptoms seizures or loss of awareness consult your physical before using video games While children play video games a parent should observe Be alert to the following symptoms dizziness altered vision eye or muscle twitching involuntary movements loss of awareness disorientation or convulsions If you or your child experiences these symptoms discontinue use immediately and consult your physician IMANUAL Keep this manual available and ready for use If the game fails to function properly turn off the machine and unplug the AC line cord Contact your local distributor Your warranty when applicable lasts 60 days from your purchase date You may not reproduce this document or any of its contents without written authorization from Raw Thrills Inc SPECIFICATIONS For reasons such as performance this product s specifications may change without notice Federal patent copyright and other intellectual property laws protect the content devices and design of the game and its equipment Page 4 2014 NAM
38. ract Mode e Garbled characters e Bad audit files To identify corrupt files press Test choose System Test Menu and run the CRC Check The only way to repair corrupt files is to recover the hard drive as detailed below COMPUTER The computer contains sensitive components including a hard drive Do not handle roughly Call your distributor before servicing its internal components Ask about warranty information as it relates to the PC Do not use the PC on off switch Turn AC power on or off with the cabinet power switch With game and PC on verify that the RIO board has power If not see Troubleshooting Open the Coin door Open the PC DVD ROM tray by reaching back to the PC and pressing the Open Close button on the drive bay adl E n Insert the first of two restore DVDs labeled Disc 1 into the tray Close the tray by pressing the Open Close button again Turn cabinet power switch to OFF Wait 30 seconds Turn cabinet power switch to ON Recovery begins automatically when PC boots up 5 m recovery does not begin check to ensure disc is inserted correctly and is not damaged 10 Initial software loading may take several minutes Check progress periodically Do not interrupt power or reset the game during recovery 11 When software has been loaded a message indicates that restore is complete When instructed to remove disc open DVD ROM drive tray and remove disc 12 Turn cabinet power switch off
39. rade 8 Steel Cap Screw 1 4 20 4 92620A539 Thread 5 8 Length 4 3 McMaster Carr Steel Split Lock Washer 1 4 Screw 91101A229 Size 49 OD 06 Thick Super Alpine Racer Pedestal Casters 4 McMaster Camr Heck m 40mm Length 5 600 01181 01 Plate Below Skis Black Class12 9 Alloy Steel Socket Head Hae Cap Screw M5 Thread 0 8mm Pitch 18 35mm Length Female Rod End Right Hand M12 7 0013640 Thread 1 75mm Pitch M12 Ball ID DIN 125 Zinc Plated Class 4 Steel Flat De Washer M12 Screw Size 24mm OD l 2 3mm Thick Metric Zinc Plated Class 8 Steel Hex eal Nut M12 Thread 1 75mm Pitch 19mm 2 Wide 10mm High 10 600 01187 01 Threaded Hex Turnbuckle Zinc Plated Class 8 Steel Left Hand 11 McMaster Carr Thread Hex Nut M12 Thread 1 75mm 73679A170 Pitch 19mm Width 10mm Height Female Rod End Leff Hand M12 X2 600 01363 0 Thread 1 75mm Pitch M12 Ball ID Super Alpine Racer Platform Mechanism Assembly AN ITEM NO PART NUMBER DESCRIPTION 603 00543 0 1 5 Hole Tread Plastic 2 500 00071 01 24CM Blue LED Great Wall Rope super Alpine Racer Pedestal Light Assembly ITEM NO PART NUMBER DESCRIPTION t Right Ski Pol ps ight 5k Pole Front Right Ski Pole Front Left Ski Pole 2 Assy Front Left Ski Pole Right_Ski_ Pol 3 yes ight_ski_Pole Rear Right Ski Pole 600 01178 01 TubetoTube Connector 2 10 McMaster Carr Black

Super Alpine Racer Service Manual

Contents

Download Pdf Manuals

Related Search

Related Contents