Home

004-xxxx-00 -Service Manual: Product name

1. Disassembly Removing the Main Board Step 2 Detach the I O board from the main board by pulling up firmly and carefully Disassembly Removing the Main Board Step 3 Set aside the connected rear cover and l O board End Result TITTY CL Lime TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 13 Disassembly Removing the Main Board continued Disassembly Removing the Main Board Step 4 To detach the main board from the front bezel e Disconnect the power cable and the pump switch cable Cables Disconnected Cables Two Screws TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 14 Reassembly Replacing the Main Board Locate the kit being installed in Specific Part Replacement and follow instructions before continuing Reassembly Reassembly Replacing the Main Board Step 2 Secure the main board in the front bezel using two screws Reassembly Replacing the Main Board Step 1 Position cables as shown here before screwing the main board to the front bezel 7 Note Be sure that the power cable and pump switch cable are not caught underneath the main board as it is screwed down Reassembly Replacing the Main Board Step 3 Reconnect cables after screws have been put in TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 1 5 lt gt O a wz N A Reassembly R
2. Midmark Corporation 2013 Revised 08 2013 Note Be sure that the power cable touch panel cable and the back light cable are not caught underneath the main board as it is laid flat on the bezel Reassembly Step 4 After the screw has been put In e Reconnect the power cable touch panel cable and backlight cable Reassembly Step 3 Position cables as shown here before screwing main board to front bezel Reassembly Replacing the Main Board Locate the kit being installed in Specific Part Replacement and follow instructions before continuing Reassembly Reassembly Replacing the Main Board Step 2 Secure the main board in the front bezel using two screws Reassembly Replacing the Main Board Step 1 Position cables as shown here before screwing the main board to the front bezel 7 Note Be sure that the power cable and pump switch cable are not caught underneath the main board as it is screwed down Reassembly Replacing the Main Board Step 3 Reconnect cables after screws have been put in TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 7 lt gt O a wz N A Reassembly Replacing the Main Board Continued Reassembly Replacing the Main Board Step 4 Plug the battery cable into the main board Reassembly Replacing the Main Board Step 5 Reattach the I O boar
3. Reassembly Replacing the Battery Door Step 1 Close the unit by replacing e all four screws e the battery and e the battery door two screws TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 18 TP204 Rev A Specific Part Installation lIQvitals Battery Door Service Kit Part 181 6741 Install IQuitals Battery Door Service Kit Step 1 Remove the two screws on the back of the unit Note The number of inputs vary depending on the unit model number Install IQuitals Battery Door Service Kit Step 2 Remove the old battery door and replace it with the new one Install IQuitals Battery Door Service Kit Step 3 Install the new battery by inserting the two screws Midmark Corporation 2013 Revised 08 2013 D 19 TP204 Rev A IQuitals Temp Assembly Service Kit Part 181 6740 Note If working with an IQvitals PC disregard instructions referencing the speaker cable Install IQuitals Temp Assembly Service Kit Step 1 Disconnect temperature and speaker cables from I O board Install IQvitals Temp Assembly Service Kit Step 2 Detach the temp assembly by removing the three screws that hold it to the rear cover Install IQuitals Temp Assembly Service Kit Step 3 Peel off the Kapton tape that se cures the speaker and temperature cables Three Screws Midmark Corporation 2013
4. Internal problem or faulty sensor A 11 Detach and reattach sensor Retest Test with a known working sensor If problem goes away replace faulty sensor If problem persists replace Main Board Refer to manufacturer s instructions for use If no red light is coming from the sensor detach and reattach sensor Retest Test with a known working sensor If problem goes away replace faulty sensor If problem persists replace Main Board Temperature Measurement Issues It is always suggested that the temperature probe manufacturers instructions for use be consulted For best practice techniques when obtaining a temperature measurement for a patient using the IQvitals or IQuitals PC device refer to the Device Operation section of the device Operation Manual Proper probe installation e Make sure the probe cord is threaded through the cord guide on the back of the device o Heavy strain on the probe can cause the probe wire to break inside the connector Periodic temperature accuracy checks e The Temperature circuitry is self calibrating e An accuracy check of the temperature circuitry should be conducted annually See section B of this Service Manual Midmark Corporation 2013 Revised 08 2013 A 12 DL K Issue Error Code Probable Cause Incorrect measurement technique or probe placement Readings seem low or high Probe damaged Internal problem Probe unplugged No mea
5. O a wz N A Note them Install IQuitals NIBP Pump Service Kit Step 6 Place the new stabilizer pad in place and insert two new tie wraps Be sure to press tie wraps against the bottom of the main board while tightening Install IQuitals NIBP Pump Service Kit Step 7 Plug pump into connector and twist several times to wrap the two pump wires together Midmark Corporation 2013 Install IQvitals NIBP Pump Service Kit Step 8 Center pump over the outline on the board and secure it with tie wraps Be sure that the wire coils back next to the pump and is also secured by the tie wraps Revised 08 2013 D 27 Install IQvitals NIBP Pump Service Kit Step 9 Reconnect the manifold to the pump and reattach the processor board to the main board using the three screws and being careful to line up the pins exactly lIQvitals Valve Assembly Service Kit Part 181 6120 Note If working with an IQvitals PC disregard instructions referencing the processor board Install IQvitals Valve Assembly Service Kit Step 1 Detach the processor board from the main board by removing all three screws and gently pulling the two boards apart Note The screw is beneath the manifold Install IQuitals Valve Assembly Service Kit Step 2 Remove the valve from the main board by unplugging it from the board and manifold Install
6. 0 or Serial Connection 1 click Set after making a change to switch connection types Comm Port Set 0 Set lemp Normal Temperature Accuracy Check Controls BP Measurement Controls Stop BF Cal Accuracy Check Controls USB IQvitalsService Test Program or IQvitals Touch Panel Calibration Program Configuration IQvitalsService Test Program or IQvitals Touch Panel Removable Disk E Calibration Program Configuration File Edit View Favorites Tools Help Step 1 To run the IQvitals programs on the IQvitals Q sak Bi Search Folders EFF GAD Folder Sync touchscreen device Address E e Copy the programs folder contents from the PC hard drive to the Startup folder in the USB drive s root di File and Folder Tasks rectory This process applies for both the lQvitalsSer vice and lQvitals Touch Panel Calibration programs iy Move the selected items Copy the selected items C E mail the selected items Delete the selected items IQvitalsService Test Program or IQvitals Touch Panel me Calibration Program Configuration My Computer z G My Documents Step 2 Once the desired program is loaded into the z A Startup folder G My Network Places Make copies of both folders e Plug the USB drive into the IQvitals touchscreen device and Details e Power the unit on e The lQvitals device will boot up and display th
7. 0 o o 181 6762 _ lQvitals Battery Bord w n it 181 6763 avis amp IOvitals PC USB Service Toos Kt w w TP204 Rev A Midmark Corporation 2013 Revised 08 2013 C 3 Parts List Service Kit Name and Number Service Kit Components 181 6110 lQvitals NIBP Pump Service Kit 181 6120 lQvitals Valve Assembly Service Kit 181 6130 lIQvitals NIBP Manifold Service Kit TP204 Rev A Midmark Corporation 2013 Revised 08 2013 C 4 Service Kit Number and Name Service Kit Components 183 6700 lQvitals Main Board w SpO2 Service Kit 183 6701 lQvitals Main Board no SpO Service Kit 183 6702 IQuitals PC Main Board w SpO Service Kit TP204 Rev A Midmark Corporation 2013 Revised 08 2013 C 5 TP204 Rev A Service Kit Number and Name Service Kit Components 183 6703 lQvitals PC Main Board no SpO Service Kit 183 6711 lIQvitals PC I O Board Service Kit 183 6712 IQvitals O Board Service Kit Midmark Corporation 2013 Revised 08 2013 a a _ Hu Service Kit Number and Name Service Kit Components 183 6720 Quitals Processor Board Service Kit Noe rei vent tty Rr 181 6740 lQvitals Temp Assembly Service Kit 181 6741 lQvitals Battery Door Service Kit TP204 Rev A Midmark Corporation 2013 Revised 08 2013 C 7 Service Kit Number and Name Service Kit Components 181 6742 lQvitals Rear Cover Service Kit
8. Revised 08 2013 D 20 ic eee Install IQuitals Temp Assembly Service Kit Install IQuitals Temp Assembly Service Kit Step 4 Attach the new temp assembly using Step 5 Pass the speaker and temperature cables the three screws through the opening at the bottom corner Note Be sure both the speaker and temperature cables are not pinched against the rear cover Install IQvitals Temp Assembly Service Kit Install IQuitals Temp Assembly Service Kit Step 6 Tape down the two cables using a Step 7 Attach the speaker and temperature cables to the piece of Kapton tape l O board Speaker Cable red and black Temp Cable black and white TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 21 TP204 Rev A IQuitals Battery Board Service Kit Part 181 6762 Midmark Corporation 2013 Revised 08 2013 Install IQuitals Battery Board Service Kit Step 1 Remove the two screws that hold the battery board and plastic bracket in place iu nk Install IQuitals Battery Board Service Kit Step 2 Remove the old battery board and put in the new battery board Secure the new board with the bracket and screws TP204 Rev A IQuitals l O Board Service Kit Part 183 6712 Note If working with an IQvitals PC disregard instructions referencing the speaker cable Install IQvuitals O Board Service Kit Step 1 Unplug the speaker and temperature
9. 181 6743 lQvitals PC Rear Cover Service Kit 181 6744 lQvitals Front Bezel Service Kit TP204 Rev A Midmark Corporation 2013 Revised 08 2013 Service Kit Number and Name Service Kit Components 181 6745 lQvitals PC Front Bezel Service Kit 181 6750 IQuitals Display Service Kit 181 6751 IQuitals Display Brackets Service Kit TP204 Rev A Midmark Corporation 2013 Revised 08 2013 C 9 Service Kit Number and Name Service Kit Components 181 6752 IQuitals Replacement Display 181 6761 IQuitals SD Card Assembly 181 6746 IQuitals Input Panel w SpO Service Kit TP204 Rev A Midmark Corporation 2013 Revised 08 2013 C 10 Service Kit Number and Name Service Kit Components 181 6747 lQvitals Input Panel no SpO Service Kit 181 6762 lQvitals Battery Board Service Kit 181 6763 lQvitals amp IQuitals PC USB Service Tools Kit TP204 Rev A Midmark Corporation 2013 Revised 08 2013 C 11 Service Part Replacement Disassembly and Reassembly of IQuitals and IQvuitals with SpO2 The following steps will guide you through the removal and replacement of components for the following device model numbers e 1 100 1610 IQvitals e 1 100 1615 IQvitals with SpO gt Tools Needed The following tools may be needed to conduct the steps outlined in this section e __ Phillips head screwdriver e Needle nose tweezers e
10. Change the simulator setting or use a hand bulb to inflate to 300 mmHg and verify that Qvitals touchscreen and or IQvitals PC releases pressure before reaching 300 mmHg e f pressure is not released before 300 mmHg check the accuracy of the test fixture If this is OK replace Main Board e Click Stop BP Cal when finished Note All testing assumes properly functional and calibrated test equipment The I Qvitals has been tested with the Fluke Biomedical BP Pump2 simulator BP simulator behavior can vary from manufacturer to manufacturer Before starting the BP simulator click Start BP Cal OwitalspcService Version 0 lvitals PC Connected Sp Code 302 PR Code 302 Temp Normal Code 302 Set Temp Monitor Set Temp Normal BP Cal Mode Start BP Meas Sop BP Meas Cuff 0 0 mmHg BP Status CN Start BF Cal Stop BF Cal Weight Power Maing TP204 Rev A Make sure that the valve releases pressure drops to zero before pressure reaches 300 mmHg Midmark Corporation 2013 Revised 08 2013 B 16 TP204 Rev A SpO2 Calibration Check SpO2 Checks Include e SpOo2 Accuracy Note The SpO2 circuitry contains a factory set calibration potentiometer This will remain stable for the life of the product and is not field serviceable Tools Needed e pOo2 Simulator Fluke Biomedical Index 2 or similar e IQvitalsService o
11. IQscale The Fairbanks scale can measure weight from 10 to 500 Ibs and receives its power from the IQvitals or IQvitalse PC device no batteries required for the scale The Midmark 625 power exam table with IQscale can measure weight from 30 to 600 Ibs Periodic weight measurement accuracy check e The Fairbanks scale is calibrated at the factory and should not need further calibration e The Fairbanks scale is self zeroing e An accuracy check of the Fairbanks scale should be conducted annually See Section B of this Service Manual e For service instructions for the Midmark 625 Barrier Free Power Examination Table with IQscale contact Midmark customer support or visit midmark com Issue Error Code Probable Cause e Check scale cable connection Scale cable not attached to device e If connected scale should power on and show weight in its local display Fairbanks scale feature not enabled device is e Confirm that the Table feature is disabled via configured to communicate with Midmark 625 with the Service Settings menu lQscale instead Ask patient to stand in the middle of the scale No reported weight Fairbanks Scale MEME MONS CSC Is patient more than 500 Ibs Weight is below scale capacity Is patient less than 10 Ibs e Check scale cable connection e If connected scale should power on and show weight in its local display Internal problem e Test with a Known working scale and o
12. Touch Q O po search Folders EE E Folder syne Panel Calibration Program onto the computer s hard Address Ser E JPE drive i i ile and Fold k e The USB drive will be re used to run these test pro ome haraam Se grams on the IQvitals device iy Move the selected items a RS Z TOvitalspeSerlice Program TOvitalsUSBInstal sr E mail the selected iterns Qvitalspcser ice Progra alsi staja gt Delete the selected items Other Places My Computer LJ My Documents Shared Documents J My Network Places Copy Both Folders onto Hard Drive TP204 Rev A Midmark Corporation 2013 Revised 08 2013 B 8 IQvitals IQvitalspc Service Test Program View lQvitals Service Program e Runs on IQuitals touchscreen device lQvitalspc Service Program e Runs on a personal computer for IQuitals PC Codes are described in Er ror Codes Section Connection Status lOvitalocService Version 0 1 lQvitals PC Connected SpO Reading SpO Code 302 PR Code 302 pele NSSCNS Temp Normal Code 302 E Set Temp Monitor Blood Pressure Reading Cuff Pressure Reading Cuff 0 0 mmHg BF status OK Weight Weight Reading Power Mains Pulse Rate Reading eee ee Power Status TP204 Rev A Midmark Corporation 2013 Revised 08 2013 B 9 Comm Port is not part of the lQvitalsServiceProgram Mini USB
13. cables from the current I O board Install IQvitals 1 O Board Service Kit Step 2 Plug the speaker and temperature cables into the new I O board Note The rear sticker will need to be replaced if extra port is exposed see photo below Midmark Corporation 2013 Revised 08 2013 D 23 Speaker Cable red and black Temp Cable black and white Swap old sticker for new one TP204 Rev A IQuitals Rear Cover Service Kit Part 181 6742 Install IQuitals Rear Cover Service Kit Step 1 Remove battery board two screws from the current rear cover Install IQuitals Rear Cover Service Kit Step 2 Remove temp assembly three screws from the current rear cover Install IQuitals Rear Cover Service Kit Step 3 Install all screws in new rear cover Install IQvitals Rear Cover Service Kit Step 4 A Carefully remove the outer sticker found on the bottom of the rear cover with a pen knife or similar tool B Remove the Serial Number and Part Number stickers and put them on the new rear cover in the same orientation C Position the new rear sticker on the new rear cover the Serial Number and Part Number should be visible through the outer sticker window Midmark Corporation 2013 Revised 08 2013 D 24 IQuitals Input Panel w SpO2 Service Kit Part 181 6746 and IQvuitals Input Panel no SpO2 Service Kit Part 181 6747 Inst
14. in connector on Processor Board If problem persists replace Processor Board Power cycle the device If problem persists reseat or replace SD Card more likely or Processor Board possible Power cycle the device If problem persists reseat or replace SD Card Charge battery by plugging device into mains power Confirm that the battery charging light on the front of the device is blinking charging If problem persists replace Main Board likely or Battery less likely aad Gauge not full after sufficient charging Battery at end of life Replace Battery Battery Life shorter than usual Midmark Corporation 2013 Revised 08 2013 A 5 Battery at end of life e Replace Battery DL K Communication Issues with IQmanager The lQvitals device can connect to a personal computer PC or laptop via a USB or serial cable This allows for the transfer of patient data between the device and Qmanager software Issue Error Code Probable Cause USB cable became detached from device or e Check cable connection lIQmanager PC e Confirm that device is on mains Device is no longer powered on e Follow the power checks from earlier in this document Cable problem e Test with a 2nd cable e Power cycle the device USB disconnect or Error Code MON 0 Internal problem e If problem persists check for damaged connector on l O Board Replace I O Board most likely or Main Board possi
15. may not be accurate if the patient is convulsive or experiencing tremors e Check for kinks in the blood pressure hose if the device reports a mea surement problem Caution PULSE OXIMETRY MEASUREMENT SpOz e Read instructions provided with the sensor to understand the best ap plication technique and all relevant safety information e Do not apply the sensor on the same limb as the NIBP cuff During blood pressure measurements the perfusion is temporarily reduced which can result in inaccurate pulse oximetry readings e Elevated levels of carboxyhemoglobin or methemoglobin can result in inaccurate pulse oximetry readings e Bright light can create problems with the pulse oximetry measure ments resulting in inaccurate readings If the sensor is in a place where it may be exposed to bright light cover it with opaque material e Pulse oximetry readings may be inaccurate in the presence of exces sive motion artifact or tremors Maintenance Cleaning Chart The following table provides instructions for cleaning the IQvitals and the lQvitals PC The devices should be cleaned monthly or as warranted Before cleaning refer to the cautions listed in the following table or refer to the Cleaning section of the Operation Manual for each device Recommended Cleaning Method Procedure IQuitals and IQvitals PC Disconnect the unit from the wall outlet Put on gloves and protective eyewear Prepare the enzym
16. not intended for continuous monitor ing Do not leave a patient unattended while taking measurements with this device WARNING IQvitals is not intended for use during patient transport WARNING To ensure patient safety only use supplies and ac cessories that are supplied with the IQvuitals and recommended by Midmark Using unapproved ac cessories can affect patient and or operator safety WARNING Regularly inspect the blood pressure cuff SpO2 cable and other accessories for damage Replace accessories as needed WARNING IQvitals is not intended to be hand held during operation WARNING Do not connect more than one patient to the device at the same time WARNING Do not route the cables of the device in a way that they may present a stumbling hazard Midmark Corporation 2013 Revised 08 2013 WARNING IQvitals is not intended for use in the following cases e Neonatal patients e Apnea monitoring e In a magnetic resonance imaging MRI envi ronment e In an electro static unit ESU environment e Applications requiring arrhythmia detection WARNING FLAMMABLE ANESTHETICS An explosion hazard exists if the monitor is used in the presence of flammable anesthetics WARNING BLOOD PRESSURE MEASUREMENT Avoid frequent and prolonged blood pressure measure ments which can result in petechia ischemia pur
17. 013 Revised 08 2013 D 10 Disassembly and Reassembly of IQuitals PC and I Qvitalse PC with SpO2 The following steps will guide you through the removal and replacement of components for the following device model numbers e 1 100 1620 IQvitals PC e 1 100 1625 IQuitals PC with SpO2 WA Tools Needed The following tools may be needed to conduct the steps outlined in this section e Phillips head screwdriver e Needle nose tweezers e Pen knife e Pliers e Wire cutters e Replacement parts for the device TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 11 Disassembly Disassembly General Step 1 Open the unit by removing the battery door two screws from the rear of the unit to expose all four screw holes Disassembly General Step 2 Remove the battery and all four screws SpO2 Disassembly General Step 3 Gently pull apart the front and rear covers of the unit Note Non SpO2 The two halves will Still be connected by two cables plugged into the 1 O and main boards TP204 Rev A Note The input panel may vary slightly depending on the unit model Midmark Corporation 2013 Revised 08 2013 Disassembly Removing the Main Board Disassembly Removing the Main Board a Step 1 To separate the main board and rear LELLLLLLLLL cover ee a e Disconnect the battery cable from the main ji board
18. Hard Drive 4 My Computer G My Documents L Shared Documents t My Network Places TP204 Rev A Midmark Corporation 2013 Revised 08 2013 B 6 Install IQuitalspcService Test Program continued Install IQuitalsService Test Program amp QvitalspcService Program Step 2 After the folder is copied to the hard drive Ee RER ee Y oy i e Open the IQvitalspcService Program the copy on the Qar GC ED JP serh E raiders KA raider sync computer Address fam Ce WOvitalspeService Program e Select IQuitalspcService exe and e C t hortcut the deskt File and Folder Tasks a re rer GES IOvitalspeService exe reate a snortcut on e des Op TODO File descriptions IQvitalspcService MFC Applica Make a new folder Publish this Folder to the SiLSExp dl web a 3 2 1 0 SUSESp bf Share this folder Note To start the IQuitalspcService Program launch IQvitalspcSer vice exe from the desktop This will start the Test Program see IQvitalsService Test Program View Other Places Local Disk C Lj My Documents G Shared Documents W My Computer My Network Places Details Create Desktop Shortcut TP204 Rev A Midmark Corporation 2013 Revised 08 2013 B 7 Install IQuitalspcService Test Program continued Install IQuitalsService Test Program Removable Disk E Step 3 File Edit View Favorites Tools Help e Copy the IQvitalsService Program and Qvitals
19. IQvitals Valve Assembly Service Kit Step 3 Cut and discard the tie wrap hold ing the valve Install IQuitals Valve Assembly Service Kit Step 4 Pull firmly on the valve to remove it from the adhesive pad and main board Install IQuitals Valve Assembly Service Kit Step 5 Remove the adhesive pad from beneath the valve if it remains on the board TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 28 TP204 Rev A Install IQuitals Valve Assembly Service Kit Step 6 Insert one new tie wrap Note Press tie wrap against the main board while tight ening to avoid having extra slack Install IQvitals Valve Assembly Service Kit Step 7 Plug the valve into the connec tor and twist several times to wrap the two wires securely together Install IQuitals Valve Assembly Service Kit Step 9 Secure the valve with the tie wrap Install IQvitals Valve Assembly Service Kit Step 8 Loop the twisted wires once around the front of the valve while attaching Note Midmark Corporation 2013 Revised 08 2013 D 29 l of the main board while tightening it to the main board by means of the adhe i g g sive pad on the underside of the valve Note Ensure that the valve is centered over the outline on the board Install IQuitals Valve Assembly Service Kit Step 11 Reattach the processor board to th
20. P204 Rev A lIQvitals Display Service Kit Part 181 6750 Install IQuitals Display Service Kit Step 1 To replace the display remove the screw that secures the blue display retainer tab in place Install IQuitals Display Service Kit Step 2 Unscrew both metal brackets two screws each and remove them Install IQuitals Display Service Kit Step 3 Remove the current display Install IQuitals Display Service Kit Step 4 Position the new display in its place Install IQuitals Display Service Kit Step 5 Secure the two metal brackets and display retainer tab the way they were removed Note Touch panel calibration is required after the replacement of processor board Refer to the IQvitals Touch Panel Calibra tion section of this Service Manual IQuitals Replacement Display Service Kit Part 181 6752 Install IQuitals Replacement Display Service Kit Step 1 Connect the new front bezel and screen to the main board Note Touch panel calibration is required after the replacement of processor board Refer to the IQvitals Touch Panel Calibra tion section of this Service Manual Midmark Corporation 2013 Revised 08 2013 D 39 TP204 Rev A IQuitals Front Bezel Service Kit Part 181 6744 Install IQvuitals Front Bezel Service Kit Step 1 To replace the front bezel remove the screw that secures the blue display retainer tab in plac
21. Pen knife e Pliers e Wire cutters e Replacement parts for the device START BP 0000 Temp Foa 98 6 F eight eigh 3MI Resp Rate Pain score CEO CES ES CLEAR lt nunnn 3 46 22 P SAVE Wi Height TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 2 Disassembly Disassembly Step 2 Remove the battery and all four screws Gently pull apart the front and rear cov ers Disassembly STEP 1 Remove the two screws to remove the battery door from the rear of unit to expose all four screw holes Disassembly Step 3 The two halves will still be connected by several cables plugged into the O board and main board as shown TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 3 TP204 Rev A Disassembly continued Disassembly Step 4 To separate the main board and rear cover e Disconnect the battery cable from the main board Disassembly Step 5 Set aside the connected rear cover and l O board Disassembly Step 6 Detach the I O board from the main board by pulling up firmly and carefully Midmark Corporation 2013 Revised 08 2013 NTI rt hl I 2 Ti End Result Disassembly Removing the Main Board Disassembly Removing the Main Board Disassembly Removing the Main Board Step 1 To detach the main board from the front Step 2 l bezel A Remove the single screw keeping the
22. TP204 Rev A lQvitals and lIQvitals PC Service and Parts Manual Model Numbers 1 100 1620 1 100 1625 1 100 1610 1 100 1615 FOR USE BY QUALIFIED PERSONNEL Language of origin English 3 100 1154 Rev A Style B GENERAL INFORMATION ue Functional Verification Tests B 11 a D D D a ee III Calibration Checks a B 12 COPE tb de crime E le died Ces III B loo d Pressure ee B 12 D Related Documents iii SpO B 17 g p p 2 ns E ae E E AE E A E A E TE S Device Warranty uen iv Ta aae B 19 5 Device amp Serial Number Location iv HS REE ee a ee OEE nn Weight B 21 Device Specifications V Te B 23 Compliance Chart V ee IOS PE evermasntiesuna Gace vi O CAUTIONS ccccccccccccccccecceccceceucssuscsusesacesanessneesanss vii PURCHASING GUIDE amp PARTS LIST Maintenance Cleaning Chart viii 5 MM Disposal ix B Ordering Service Parts C22 a aD Purchasing Ae OG ae eo toi G 3 c OE Pars LIST C 4 A TROUBLESHOOTING s ai D Device Description A 2 CAE General Troubleshooting Notes AD Error Codes A 3 Ke Power ISSUES A 4 Ke Communication Issues with IQmanager A 6 2 SERVICE PART REPLACEMENT Blood Pressure BP Measurement Issues A 7 ie a ee ee 4 10 BE I vitals and IQvitals with SpO2 D 2 Pulse Oximetry SP0 Measurement issues Cp Disassembly ee D 3
23. Temperature Measurement Issues A 12 EE A E D 5 eee BNR NAV CELOS VIE ATIE T LANIA NA sw Weight Measurement Issues A 15 a e bi FR EE pee Reassembly Sasa eee D 6 Ce a D i R olacinc th Mat Do occ D 7 Touchscreen User Interface Issues A 18 ei ac ee ae es D 9 p g eee eee eee m Replacing the Battery Door D 10 c IQvitals PC and IQvitals PC with SpO2 D 11 fem SERVICE TOOLS amp CALIBRATION CHECKS Disassembly assainies D 12 a P f S Qvitals IQvitalsoc USB Service Tools Kit B 2 Removing the Main Board D 13 D OVerV W 0 cccccccccecccceccccucccccccccsecccsesseesssesesaesess B 2 Replacing the Main Board D 15 One time Installations B 2 Replacing the Back Panel D 16 lt Install IQvitals IQvitalsoc USB Service Tools Kit B 3 Replacing the Battery Door D 18 Install IQuitalSUSBINSHAIIRr B 4 Specific Part Installation D 19 x Install IQvitalspcService Test Program B 6 S IQvitals IQvitalsoc Service Test Program View B 9 5 USB IQvitalsService Test Program B 10 IQuitals Touch Panel Calibration Program ConfiguratiON s dntrns hapten irner ec nrigersiontpnattmennder teeters B 10 Midmark Corporation 2013 Revised 08 2013 Il Symbols Scope DANGER Indicates an imminently hazardous situation which will result in serious or fatal injury if not avoided This symbol ts used only in the most extre
24. Windows is a registered trademark of Microsoft Corporation in the US and other countries Fairbanks and TeleWeigh are registered trademarks of Fairbanks Scales Inc DuPont and Kapton iare are traedemarks or registered trademarks of E I du Pont de Nemours and Company Midmark Corporation 2013 Revised 08 2013 iii TP204 Rev A Device Warranty Any device covered under Midmark s Limited Warranty term shall be serviced by Midmark only Service by any person or entity other than midmark on a Midmark device will void the Warranty and the device will not be eligible for coverage under an extended service agreement To confirm the Limited Warranty term for a specific device contact midmark Support Services and provide the device serial number see Device Model Number and Serial Number Location Device Model Number and Serial Number Location To identify and order service parts it is important to have the correct device model number of the device to be serviced Both the device model number and the serial number are located on bottom of the device Device Number Kit Part Number Device Model Number IQvitals PC with SpO2 4000 0410 1 100 1625 IQvitals touchscreen with SpO2 4 000 0510 1 100 1615 80 98 98 6 EXD CONS CE CS CLEAR lt nunus 34622 Fa SAVE Device Model Number and Serial Number Label Midmark Corporation 2013 Revised 08 2013 iV K Device Specifications General Performa
25. able with or without the SpO function A thermal printer purchased from Midmark can be connected to the IQvitals device but does not connect to the IQvitals PC device General Troubleshooting Notes As a general rule it is good idea to power cycle the device to see if a problem persists The device has numerous self checks that will continue to trigger if the issue persists It is often necessary to isolate a problem to a particular component the device the power supply a patient sensor etc It is a good idea to swap in a known working component to see where a problem lies Confirm that Midmark approved SpO sensors and temperature probe covers are being used Midmark Corporation 2013 Revised 08 2013 A 2 DL Error Codes The following table contains the error codes that may be encountered while operating the IQvitals or IQvitals PC devices All error codes will appear in separate boxes similar to the image below See the Troubleshooting section of this Service Manual for each code s appropriate corrective action QVitals had a problem measuring Error Code TEMP 313 he Mentor Was Pot Ae Corrective Action Check the TEMP probe placen A Tale rey pui Hate Ar E cureme ll CLOSE OT ee Indication Oro e Indication NIBP 314 Weak signal BAT 325 Battery low SpO 302 Unplugged REC 327 Recorder door open SpO 305 Artifact REC 328 Recorder paper out SpO 306 Hardware failure REC 329 Reco
26. ale contact Midmark customer support or visit midmark com Weigh Checks Include e Weight Accuracy Tools Needed e 4 Calibrated 50 Ib Weights e IQvitalsService or lQvitalspcService Test Program depending on unit model Test Set up Note This procedure requires the Test Program to be installed For installation instructions see section IQvitals IQvitalsoc USB ServiceTools Kit e Connect the scale to the device e For an IQvitals touchscreen device run the lQvitalsService Test Program e For an lQvitals PC device run the QvitalsocService Test Program on a PC Midmark Corporation 2013 Revised 08 2013 B 21 TP204 Rev A Weight Calibration Check Procedure e Place weights on the scale to check the calibrated weight against the reported weight in the program display e Check weight at 50 100 and 200lbs e Ensure that the reported weight is within 1lb of the calibrated weight e If scale is out of range contact Midmark Support Services at 1 800 624 8950 option 2 for further information OvitalspcService Version 0 1 lQvitals PC Connected Exit Sp02 Code 302 Comm Port Set E PR Code 302 sa Temp Normal Code 302 Set Temp Monitor Set Temp Normal ji Start BF Meas Stop BP Meas Cuff 0 0 mmHg BP Status OK Ensure that the reported weight a is within specifications Weight 200 0 Ibs Power Mains Midmark Corporation 2013 Revised 08 2013 B 22 K Touchscree
27. all IQuitals Input Panel Service Kit Step 1 Disconnect the manifold from the input panel Then install the new input panel by replacing the screws and reconnecting the manifold Install IQuitals Input Panel Service Kit Step 2 Remove the two screws holding the input panel in place Install IQuitals Input Panel Service Kit Step 3 Install the new input panel by replacing the screws and reconnecting the manifold TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 2 5 TP204 Rev A lQvitals NIBP Pump Service Kit Part 181 6110 Note If working with an IQvitals PC disregard instructions referencing the speaker cable Install IQuitals NIBP Pump Service Kit Step 1 Detach the processor board from the main board by re moving all three screws and gently pulling the two boards apart Note The screw is beneath the manifold Install IQuitals NIBP Pump Service Kit Step 3 Cut and discard the two tie straps hold ing the NIBP pump Install IQuitals NIBP Pump Service Kit Step 2 Unplug the manifold and pump wires Install IQvitals NIBP Pump Service Kit Step 4 Pull firmly on the pump to remove it from the adhesive stabilizer pad and the main board Install IQuitals NIBP Pump Service Kit Step 5 Remove the adhesive stabilizer pad from beneath the pump Midmark Corporation 2013 Revised 08 2013 D 26 lt gt
28. anual Thermal Printer Not Printing e Test with a known working printer or different device to isolate problem If problem is device Internal problem related replace Processor Board possible SD Card possible O Board unlikely or Main Board unlikely Midmark Corporation 2013 Revised 08 2013 A 17 K Midmark Corporation 2013 Touchscreen User Interface Issues Issue Error Code Probable Cause No Touch Response Display image is corrupted not steady missing colors vertical lines on image Display is dark even though device is running power switch is illuminated audio feedback is heard when temperature probe is removed from the well Can t delete patient readings from memory or change device settings Pop up message appears Poor sound quality Time of Day on device is incorrect after power cycle MON 332 Monitor fault Revised 08 2013 Touchscreen out of calibration or not working Internal problem Internal problem SD card problem Internal problem Internal problem Internal problem Power cycle the device If problem persists re calibrate touch panel See Section B of this Service Manual If touch screen cannot be re calibrated e g no response to touch reseat touch panel cable in connector on Main Board Recalibrate If problem persists replace touch panel which is part of the Display likely touch panel cable connector which is part o
29. atic detergent or disinfectant solution according to the manufacturer s instructions and in separate containers Apply detergent to the product using a soft cloth If the material is dried on allow it to sit for one minute Wipe smooth surfaces with the cloth Use a soft bristle brush on visibly soiled areas and irregular surfaces Remove the detergent from the product using a cloth dampened in distilled water Repeat as necessary Apply the disinfectant solution to the affected area using a soft cloth Allow the product to sit for five minutes Wipe away excess solution and clean the product again with a cloth dampened in distilled water Allow two hours for drying Procedure SpO Sensor Remove sensor from the patient and disconnect the sensor cable from the device prior to cleaning 2 Refer to the cleaning instructions from the sensor manufacturer Temperature Probe Covers Temperature probe covers are for one time use only NIBP Cuff Refer to the cleaning instructions from the cuff manufacturer DOAA mm p A I J A IA IN d ke O L Ir LU4 KeV A Midmark Corporation 2013 viii DL Disposal The disposal of accessories such as blood pressure cuffs temperature probes and SpO gt sensors should be carried out according to the manufacturer s recommendations The lQvitals and IQvitals PC devices contain a lithium ion battery and electronic circuit boards that
30. ble USB or serial cable not attached to device or Check cable connection IQmanager PC Device is not powered on Follow the power supply checks e Confirm that the communication set up is Wrong communication set up correct on the IQmanager PC USB or Serial Port correct Serial Port number Cable problem e Test with a Known working cable e Power cycle the device Computer won t connect to the device Internal problem e If problem persists check for damaged connector on l O Board Replace I O Board most likely or Main Board possible Midmark Corporation 2013 Revised 08 2013 A 6 Blood Pressure BP Measurement Issues It is always suggested that the cuff manufacturers instructions for use or product insert be consulted For best practice techniques when obtaining blood pressure measurement for a patient using the IQvitals or IQvitals PC device refer to the Device Operation section of the device Operation Manual Periodic BP measurement accuracy check e The BP circuitry contains a calibration potentiometer that is set at the factory This potentiometer will remain stable for the life of the product and is not field serviceable e An accuracy check of the BP pressure transducer and a leak test should be conducted annually See Section B of this Service Manual Issue Error Code Probable Cause e Refer to the Operation Manual for recommended measurement technique Incorrect meas
31. calibrated water bath TEMP 306 e Power cycle the device Hard fail Internal problem MAWAS Tales f problem persists replace Main Board e Wait 10 seconds between measurements so probe can return to a valid starting temperature point Probe is too warm at start of measurement process gt 92 F e Check for proper oral or axillary temp setting e Hold probe steady and retake measurement It is taking too long to get a stable temperature Refer to the Operation Manual for proper probe TEMP 313 placement C t annot measure Test with a known working probe Room is too cold lt 60 F e Retake measurement in warmer environment Room is too warm gt 92 F e Retake measurement in cooler environment Retake measurement Probe heating element not working Test with a known working probe If problem persists replace Main Board e Power cycle the device and retake measurement TEMP 315 Probe fault Faulty probe e Test with a known working probe e If problem persists replace Main Board TEMP 330 Temperature reading lt 95 F e Verify correct temperature measurement with a Temp too low Sa Babee calibrated water bath Midmark Corporation 2013 Revised 08 2013 A 14 K Weight Measurement Issues The lQvitals and IQvitalse PC devices can connect to either a Fairbanks TeleWeigh digital floor scale or a Midmark 625 Barrier Free Power Examination Table with
32. d to the main board tak ing great care to line up the pins correctly Reassembly Replacing the Main Board Step 6 Assemble the two halves together by sliding both ends of the I O board into their corresponding plas tic grooves in the rear cover Note Be careful not to pinch any wires between the two halves see photo Midmark Corporation 2013 Revised 08 2013 The I O board is disconnected from the main board to show orientation in plastic grooves TP204 Rev A Reassembly Replacing the Back Panel Reassembly Replacing the Back Panel Step 1 Plug the battery cable into the main board Reassembly Replacing the Back Panel Step 2 Reattach the I O board to the main board Note Be sure to line up the pins correctly Reassembly Replacing the Back Panel Step 3 Assemble the two halves together by sliding both ends of the I O board into their corresponding plas tic grooves in the rear cover Note Be careful not to pinch any wires between the two halves Midmark Corporation 2013 Revised 08 2013 The I O board is disconnected from the main board to show orientation in plastic grooves Reassembly Replacing the Battery Door Reassembly Replacing the Battery Door Step 1 Close the unit by replacing A all four screws B the battery C the battery door two screws TP204 Rev A Midmark Corporation 2
33. e Install IQuitals Front Bezel Service Kit Step 2 Unscrew both metal brackets two screws each and remove them Install IQvitals Front Bezel Service Kit Step 3 Remove the display Install IQvitals Front Bezel Service Kit Step 4 Position the display in the new front bezel Install IQuitals Front Bezel Service Kit Step 5 Secure the two metal brackets and display retainer tab the way they were removed IQuitals PC Front Bezel Service Kit Part 181 6745 Install IQuitals PC Front Bezel Service Kit Refer to the Disassembly and Reassembly IQvitals PC with SoO2 model 1 100 1625 and IQvitals PC without SoO2 model 1 100 1620 begin ning on page C 9 switching out the old front bezel for the new one in between steps Midmark Corporation 2013 Revised 08 2013 D 40 This page intentionally left blank for notes SUBJECT TO CHANGE WITHOUT NOTICE Midmark Corporation For contact information go to MIDMARI lt midmark com Because we care
34. e e Prepare a Calibrated Water Bath at approximately 98 6 F e For an lQvitals touchscreen device run the lQvitalsService Test Program e For an lQvitals PC device run the lQvitalspcService Test Program on a PC Midmark Corporation 2013 Revised 08 2013 B 19 Temperature Calibration Check Procedure e Click Set Temp Monitor on the Test Program see picture to directly read the temperature of the probe tip e Place the temperature probe into water bath and check that the Test Program temperature is within 0 3 F of the water bath e If temperature is out of tolerance check the accuracy of the test fixture If this is OK replace the probe most likely O Board possible or Main Board possible Before placing the Temperature Probe into the Calibrated Water Bath click Set Temp Monitor lOvitalepcService Version 0 1 lQvitals PC Connected SpO2 Code 302 PR Code 302 Temp Monitor 98 6 degF Set Temp Monitor Set Temp Normal BP Start BP Meas Stop BP Meas BP Status OK Weight Power Mains Ensure that the temperature reading is within specifications TP204 Rev A Midmark Corporation 2013 Revised 08 2013 B 20 Weight Calibration Check This procedure is for the Fairbanks TeleWeigh digital floor scale which is calibrated at the factory and should not need further calibration For service instructions for the Midmark 625 Barrier Free Power Examination Table with I Qsc
35. e SD card detach the processor board from the main board by removing all three screws and gently pulling the two boards apart Install IQuitals SD Card Assembly Step 2 Remove the Kapton tape and old SD card from the SD reader slot on the processor board Install IQuitals SD Card Assembly Step 3 Replace the SD card and reattach the processor board to the main board using the three screws TP204 Rev A Note Be careful to line up pins exactly Midmark Corporation 2013 Revised 08 2013 D 37 TP204 Rev A lQvitals Display Brackets Service Kit Part 181 6751 Install IQuitals Display Brackets Service Kit Step 1 To replace the display brackets remove the two metal brackets two screws each Install IQvitals Display Brackets Service Kit Step 2 To install the new brackets position the wider bracket above the switch panel and the thinner bracket on the opposite side Install IQuitals Display Brackets Service Kit Step 3 Start each of the four screws to make sure that the screen is positioned properly before tightening each screw Note Do not over tighten screws but make sure that the brackets do not move after installation 7 Note When replacing the brackets make sure that the wider bracket is on the left above the switch panel and the thinner bracket is on the right Midmark Corporation 2013 Revised 08 2013 D 38 T
36. e SpO2 measurements are out of tolerance replace Main Board Note All testing assumes properly functional and calibrated test equipment The I Qvitals has been tested with the Fluke Biomedical Index 2 simulator SpO simulator behavior can vary from manufacturer to manufacturer Ensure that readings are within specifications Display Changes to Numerical Value SpO2 96 SpO2 Code 302 PR Code 302 PR 75 bom lOvitalspcService Version 0 1 x hyitals PC Connected Exit SpO2 96 TRE m PR 75 bpm Temp Normal Code 302 Set Temp Monitor Set Temp Normal Ei stat BF Meas Stop EP Meas Cuff 0 0 mmHg Start BP Cal Stop BP Cal BP Status OK Weight Power Mains Midmark Corporation 2013 Revised 08 2013 B 18 Temperature Calibration Check Temperature Checks Include e Temperature Accuracy Note The Temperature circuitry self calibrates using internal high precision reference resistors The device will report a TEMP 306 error code if the circuitry is out of tolerance Tools Needed e Calibrated Water Bath e IQvitalsService or lQvitalspcService Test Program depending on the device model number e Temperature Probe Test Set up Note This procedure requires the Test Program to be installed For installation instructions see section Qvitals IQvitalsoc USB Service Tools Kit e Connect the temperature probe to the IQvitals touchscreen and or Qvitals PC devic
37. e con figured test program automatically Note The USB drive can only be configured to run one program at a time Be sure to delete the Startup folder contents using the drive to run a new program Note When the IQvitals touchscreen is connected to a USB drive with a Startup folder it will run the executable files within that folder instead of the IQvuitals software in the device TP204 Rev A Midmark Corporation 2013 Revised 08 2013 B 10 K Functional Verification Checks amp Calibration Checks Functional Verification Checks Perform a functional verification check annually or after repairing a device lQvitals Function Procedure Mechanical Integrity Check for cracks abrasive edges and other signs of damage Power Supply LED Verify that the green power LED is illuminated on the lQvitals Power Supply when the power supply is plugged into AC power Battery Charging LED Verify that the green battery charging LED is illuminated on the lQvitals power supply when the power supply is plugged into AC power On Off LED a that the green On Off LED is illuminated on the back of the IQvitals device when the unit Verify that the device continues to run after it has been disconnected from mains and that the Battery battery gas gauge displays the correct charge level Verify that the speaker sounds when the SpO finger clip is attached to your finger and is sensed Speaker by the device Ver
38. e main board using the three screws Note Be careful to line up the pins exactly Note The screw is beneath the manifold Install IQvitals Valve Assembly Service Kit Step 10 Reconnect the manifold Be sure to press the tie wrap against the bottom IQuitals NIBP Manifold Service Kit Part 181 6130 Install IQvuitals NIBP Manifold Service Kit Install IQuitals NIBP Manifold Service Kit Step 2 Attach the new NIBP manifold by connecting it to both valves the pump the main board and the SpO panel Step 1 Remove the NIBP manifold by unplugging it from all connections Step 1 and Step 2 TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 30 IQuitals Main Board w SpO Service Kit Part 183 6700 and IQvitals Main Board no SpO Service Kit Part 186 6701 Note If working with an IQvitals PC disregard instructions referencing the processor board Install IQvuitals Main Board Service Kit Step 1 Detach the processor board from the current main board by removing all three screws Note The screw is beneath the manifold Install IQuitals Main Board Service Kit Step 2 Gently pull the two boards apart TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 31 TP204 Rev A Install IQvitals Main Board Service Kit Step 4 Remove the input panel and install it on the new main board by
39. e product and is not field serviceable e An accuracy check of the SpO circuitry should be conducted annually See Section B of this Service Manual Issue Error Code Probable Cause e Refer to manufacturer s instructions for use e Retake measurement Wait for measurement Incorrect measurement technique w value to stabilize e Test with a known working device Sensor problem e Test with a known working sensor e Test probe with a known known device Readings seem low or high Internal problem e Perform a BP Calibration Check See Section B of this Service Manual Pa The Spo cable is disconnected from the device e Connect the SpO cable to the device Unplugged SpO gt 305 Artifact Too much patient movement Ask patient to remain still SpO gt 306 Power cycle the device Hard fail Internal problem E A If problem persists replace Main Board Cannot measure es eae tti t e Refer to manufacturer s instructions for use Been ee E tye Incorrect sensor size or too much motion SPO2 1 j Weak patient pulsations e Refer to manufacturer s instructions for use Weak signal Midmark Corporation 2013 Revised 08 2013 A 10 DL SpO gt 315 Check sensor SpO gt 316 Check sensor No response by device when SpO sensor is applied to the patient Midmark Corporation 2013 Revised 08 2013 Faulty sensor Cannot measure The SpO sensor is misaligned or came off the patient
40. ed e Part numbers and quantities of service parts to be ordered e Payment information For payment details and placing an order contact Midmark Client Services eMail clientservices midmark com Phone 800 624 8950 option 6 Hours 6 30 am to 4 30 pm PST Monday through Friday Midmark Corporation 2013 Revised 08 2013 C 2 Purchasing Guide The following chart identifies all available service kits for the IQvitals and IQuitals PC devices 181 6110 a NIBP Pump 781 6120 aviels ane Assembly SSS or PE S S 183 6700 _ lQvitals Main Boara w spo Sooo o el ll 183 6702 IQvitals PC Main Board a spo O Ooo o 183 6703 _ lQvitals PC MainBoard nospo O ooo o o 836711 iowtasPCOBoara w p a o 836712 Qu Bord O O O o o n o oa O 1836720 lQvitals ProcessorBoard o o J gt n 181 6740 _ lQvitls Temp Assemby x 0 n 1816741 _ IQvitals Battery Door n 816742 iOvtasRearcover O o o O o a O 816743 iOvtasPCRearcover w p x O ooo o 181 6744 vit Front Bee o y o ooa 181 6745 iOvtasPCFomtBez w po S oo 816750 Qui Display o y e ooa 1816751 IQvitals Display Brackets OOOO O ooo o e ooa 1816752 IQvitals Replacement Display o o f n 1816761 _ lQvitls SD Cardassembly o o o a O 181 6746 _ lQvitals Input Panew Sp o oa 181 6747 iOvtalsnputPanel nosp0 w
41. eplacing the Main Board Continued Reassembly Replacing the Main Board Step 4 Plug the battery cable into the main board Reassembly Replacing the Main Board Step 5 Reattach the I O board to the main board tak ing great care to line up the pins correctly Reassembly Replacing the Main Board Step 6 Assemble the two halves together by sliding both ends of the I O board into their corresponding plas tic grooves in the rear cover Note Be careful not to pinch any wires between the two halves see photo Midmark Corporation 2013 Revised 08 2013 The I O board is disconnected from the main board to show orientation in plastic grooves TP204 Rev A Reassembly Replacing the Back Panel Reassembly Replacing the Back Panel Step 1 Plug the battery cable into the main board Reassembly Replacing the Back Panel Step 2 Reattach the I O board to the main board Note Be sure to line up the pins correctly Reassembly Replacing the Back Panel Step 3 Assemble the two halves together by sliding both ends of the I O board into their corresponding plas tic grooves in the rear cover Note Be careful not to pinch any wires between the two halves Midmark Corporation 2013 Revised 08 2013 The I O board is disconnected from the main board to show orientation in plastic grooves Reassembly Replacing the Battery Door
42. f the Main Board possible or Processor Board possible Power cycle the device If problem persists reseat display cable in connector on Processor Board If problem persists replace Processor Board possible or Display less likely Power cycle the device If problem persists reseat backlight cable in connector on Main Board If problem persists replace Display more likely or Main Board possible Power cycle the device If problem persists reseat or replace SD Card more likely or replace Processor Board possible Replace speaker which is part of the Rear Cover possible or Processor Board less likely If problem persists replace Processor Board more likely or coin cell battery which is part of the Main Board possible Power cycle the device If problem persists replace Main Board possible or Processor Board possible DL Service Tools amp Calibration Checks Midmark Corporation 2013 Revised 08 2013 K IQvitals IQvitalsPC USB Service Tools Kit Overview The IQvitals IQvuitalsPC USB Service Tools Kit P N 181 6763 Includes e Qvitals Service Program runs on the lQvitals touchscreen device from a USB drive providing the ability to conduct accuracy and safety service level functions e QvitalsPC Service Program runs on a personal computer and connects to an lQvitals PC device providing the ability to conduct accuracy and safety service level funct
43. ices department at 1 800 624 8950 option 2 and be prepared to describe the problem Caution To ensure proper operation perform routine inspection and maintenance on the device according to the instructions in this Service Manual Caution Do not make any modifications to the device Any modifica tions made will void the warranty A A A A A A A Midmark Corporation 2013 Revised 08 2013 Caution Refer servicing to qualified personnel Caution ARRHYTHMIA PATIENTS The IQvitals device is designed to operate in the presence of cardiac arrhythmias However the pulse rate meter may be adversely affected in some cases Caution BLOOD PRESSURE MEASUREMENT e Do not allow the blood pressure cuff or hose to come into contact with fluids If this occurs See Cleaning of the devices Operations Manual for drying instructions e Check the hose and cuff frequently for signs of damage or debris An obstruction in the hose may interfere with inflation and deflation result ing in inaccurate readings e To obtain accurate blood pressure readings keep the limb and cuff motionless e The blood pressure cuff should be at the same level as the patient s heart If you cannot place the NIBP cuff at this level add 1 4 mmHg to the measured pressure values for each 2 cm above the heart level or subtract 1 4 mmHg for each 2 cm below heart level e Blood pressure measurements
44. ify the accuracy of the SpO2 parameter with the SpO9 simulator at 96 SpO gt NIBP Verify the BP accuracy against the simulator at a BP of 120 80 Verify the temperature accuracy with a calibrated water bath at or near 98 6 F Verify the scale accuracy against calibrated weights Midmark Corporation 2013 Revised 08 2013 B 11 Calibration Checks Perform safety and calibration checks annually Blood Pressure BP Calibration Check BP Checks Include e BP Accuracy e Cuff Pressure Accuracy e Leak Rate e Overpressure Detection Note The BP circuitry contains a factory set calibration potentiometer This will remain stable for the life of the product and is not field serviceable Tools Needed e BP Simulator Fluke Biomedical BP Pump 2 or equivalent e IQvitalsService or QvitalspcService Test Program depending on the device model number e BP Hose Test Set up Note Each procedure requires the correct Test Program to be installed For installation instructions see section Qvitals IQvitalsoc USB ServiceTools Kit e Connect the IQvitals touchscreen or IQvitals PC device to simulator using a BP hose see picture e For an lQvitals touchscreen device run the lQvitalsService Test Program e For an lQvitals PC device run the lQvuitalspcService Test Program on a personal computer Midmark Corporation 2013 Revised 08 2013 B 12 lt L gt O x wz N A Note IQuitals touchscreen co
45. ions e Qvitals Touch Panel Calibration Program runs on the Qvitals touchscreen device from the USB drive providing the ability to calibrate the touchscreen e QvitalsUSBInstaller enables a USB connection for lQvitals PC Note USB connection only operates on personal computers running Windows XP or Windows 7 One time Installations e QvitalsUSBInstaller e IQvitalspcService Test Program e Saving lQvitals Test Harness Folders Midmark Corporation 2013 Revised 08 2013 B 2 TP204 Rev A Install IQuitals IQuitals PC USB Service Tools Kit Install IQuitals IQvitalsPC USB Service Kit Step 1 Connect IQuitals IQvitalsPC USB Service Tools Kit part 181 6763 to your Windows XP or Windows computer Install IQuitals IQvitalsPC USB Service Kit Step 2 Using Windows Explorer view the contents of the USB stick see picture displaying contents of USB Midmark Corporation 2013 Revised 08 2013 Removable Disk E File Edit View Favorites Tools Help pack hi Search Wea Folders BE A Folder Sync Address E z FR FT Der if poe mes File and Folder Tasks Ga TOwitalsService Program LJ pan Touch Panel Calibration 2 Make a new Folder E Publish this folder to the a EEN a Web La IQvitalspcService Program nl IOvitalsUSBInstaller Share this Folder Other Places ig My Computer Lj My Documents Shared D
46. is out of tolerance confirm that the test fixture is not the source of the leak Check all connections on the NIBP Manifold and retest If leak rate is still out of tolerance check or replace Valve Assembly most likely NIBP Manifold possible step valve which is part of the Main Board possible or Pump unlikely e Click Stop BP Cal when finished Note All testing assumes a properly functional and calibrated test equipment The IQvitals has been tested with the Fluke Biomedical BP Pump2 simulator BP simulator behavior can vary from manufacturer to manufacturer Before starting the BP simulator click Start BP Cal OvitalspcService Version lOvitals PC Connected SpO Code 302 Comm Port Set E PR Code 302 Temp Normal Code 302 Set Temp Monitor SetTempNomal BP Cal Mode Start BP Meas Stop BP Meas uff 0 0 mmi N smgca Cuff 0 0 mmHg Start BP Cal Stop BP Cal BP Status OK Weight Power Maing TP204 Rev A Compare the Test Program reading to the BP simulator for one minute once the simulator reaches 200 mmHg Midmark Corporation 2013 Revised 08 2013 B 15 Overpressure Detection Calibration Check e Click Start BP Cal e Set the BP Simulator to Pressure Gauge mode and inflate it to 200 mmHg e Wait 10 seconds for the pressure to stabilize If the simulator does not have a built in pump then use a hand bulb and calibrated manometer to inflate it to 200 mmHg e
47. leak test with a significant leak check or replace Valve Assembly most likely or step valve which is part of the Main Board possible or Pump unlikely Instruct patient to remain still NIBP 312 eu Measurement was taking too long to complete Retake measurement Inflation pressure was less than patient s systolic Retake measurement at higher inflation pressure pressure Wait 10 seconds after powering on device or Device is auto zeroing after power up connecting to device NIBP 313 Cannot measure Retake measurement Check that cuff is not too large for patient Patient s pulse signal is too small Check cuff for proper fit and placement Retake measurement Check that cuff is not too large for patient NIBP 314 Weak signal Patient s pulse signal is too small Check cuff for proper fit and placement Retake measurement Midmark Corporation 2013 Revised 08 2013 A 9 Pulse Oximetry SpO2 Measurement Issues It is always suggested that the SpO2 sensor manufacturers instructions for use or product insert be consulted For best practice techniques when obtaining an SpO measurement for a patient using the lQvitals or IQvitals PC device refer to the Device Operation section of the device Operation Manual Periodic SpO2 measurement accuracy check e The SpO circuitry contains a calibration potentiometer that is set at the factory This potentiometer will remain stable for the life of th
48. main e Disconnect the power cable touch panel cable board on the front bezel and backlight cable connecting the screen and B Disconnect the Poa cable touch panel the main board cable and backlight cable connecting the Unplug Cables screen and the main board Single Screw Disconnected Pictures show underside of main board Disassembly Removing the Main Board Step 3 A Tilt the main board up from the bezel B Open the cable door that connects the display cable to the processor board C Separate the main board and processor board D Close the cable door on the processor board to avoid damage Unclip cable door TP204 Rev A Midmark Corporation 2013 Revised 08 2013 D 5 TP204 Rev A Reassembly Locate the kit being installed in Specific Part Replacement in Section D of this Service Manual and follow the instructions before continuing Reassembly Reassembly Step 1 To secure the main board back on front bezel e Connect the display cable from the screen assembly to the processor board see alignment pictures Note Secure the display cable by sliding it into the connector Ensure a solid connection by making sure the cable sits in the door straight and not angled both shown If door does not easily snap closed reposition the display cable DO NOT FORCE wie PTET EVENT es W L TELL Terai Reassembly Step 2 Secure the main board using one screw
49. me conditions The IQvitals and Qvitals PC Service and Parts Manual is intended for use only by experienced Biomed service personnel This manual provides information regarding troubleshooting maintenance and performance checks calibration verification as well as guides service personnel through the identification and WARNING replacement of field serviceable components for these devices Indicates a potentially hazardous situation which could result in serious injury if not avoided For detailed information regarding the operation and functions of the IQvitals and IQvitals PC devices refer to the applicable device Operation Manuals see Related Documents Fr Caution Indicates a potentially hazardous situation which may result in minor or moderate injury if not avoided It may also be used to alert against unsafe practices Equipment Alert O Indicates a potentially hazardous situation which could result in equipment damage if not avoided Note Used for special instructions or additional information Related Documents One or more of the following documents may need to be referenced in addition to the information contained within this Service and Parts Manual D Document Name Midmark Part amp Link 3 100 1056 3 100 1059 003 2425 00 TP204 Rev A 6 UJS IQvitals IQmanager Barrier Free and IQscale are trademarks of Midmark Corporation
50. n running the Test Harness When Code 306 is reported as the NIBP parameters either at start up or after starting a measurement check the NIBP status field for the fault description If NIBP status is Pump Transducer Failure 1 the NIBP Manifold tubing may have become disconnected from the transducer or pump 2 the Pump may not be starting or 3 the transducer may be faulty Inspect the NIBP Manifold and retest If problem persists listen for the sound of the Pump at measurement start must power cycle the device first If Pump is not starting replace Pump most likely or Main Board possible If Pump is starting replace transducer which is part of the Main Board If NIBP status is Pressure Not Releasing check NIBP Manifold tubing for debris or replace possible or replace Valve Assembly possible For all other NIBP status replace Main Board DL Ja Issue Error Code Probable ProbableCause i O Chek Attach BP hose BP hose is not attached to device or cuff Retake measurement Test with a known working cuff Cuff may be worn or damaged e Retake measurement e Check cuff for proper fit Cuff is too loose e Retake measurement NIBP 311 e Perform Leak Test See Section B of this Open line Service Manual e f device fails leak test with a small steady leak check all connections on NIBP Manifold or Leak in device s internal pneumatic system replace Retest e f device fails
51. n Calibration The Touch Panel Calibration Program runs on the IQvitals touchscreen device from a USB drive It allows you to calibrate the touch panel In normal use the touch panel does not need recalibrating However touch panel calibration is required after the replacement of the display or processor board Tools Needed e Stylus e Touch Panel Calibration Program Touch Panel Calibration Procedure Note This procedure requires the Touch Panel Calibration Program to be installed For installation instructions see section USB lQvitalsService Test Program or IQvitals Touch Panel Calibration Program Configuration e Connect the USB drive with the IQvitals Touch Panel Calibration Program to the device e Run lQvitals the Touch Panel Calibration Program will automatically start e Follow the Touch Panel Calibration screen instructions using a stylus e Ifthe touch panel calibration is successful a second window will open This will allow you to save the touch panel calibration constants and complete the calibration Note The touch panel calibration sequence will automatically restart if calibration is not successful Midmark Corporation 2013 Revised 08 2013 B 23 Purchasing Guide amp s Parts List S XXX XXXX XX DP XXX XXXX XX Ordering Service Parts When placing a service parts order please have the following information available e Device model number and serial number of the device to be servic
52. nce Category Specification Product Name lQvitals and IQvitals PC Product Type Non invasive automated multi parameter vital signs device Product Weight IQvitals 3 9 Ibs 1 77 kg IQvitals PC 3 2 Ibs 1 45 kg Product Dimensions 10 5 L X FE W X 7 H 0 27 x 0 10 x 0 18 m Power Requirements 100 240 VAC 0 7 A max Battery Requirements Battery Type Rechargeable 10 8 V lithium ion Low Power Indicator Automatic Shutdown on low power Operating Time Approximately 8 hours Leakage Current Meets AAMI IEC CSA 60601 1 requirements Battery Charge Time 4 hours to fully charge 3 hours for 95 charge Type of Protection Electrical Degree of Protection Water Disinfecting Method Degree of Safety Flammable Anesthetic Mixture EMC Standard Device Connectivity Accessory Connectivity Compliance Chart Complies To All Models Fire Code Rating Safety i AAMIES 60601 CSA C22 2 60601 1 IEC 60601 1 IEC 60601 1 2 IEC 80601 2 30 156 9919 2005 _ VAC Cycles 1 2005 2008 2005 2007 Class B 2009 10 Hz Electrical Ratings OS SE ee RES ee ee CNE ES RTL DE PE PE EE RE EE RC COS 800 240 Serco sinc cc a a a S GRR Je ee OT ER 0 ry N A F4 LZUT IP Midmark Corporation 2013 Revised 08 2013 V Warnings WARNING Do not use this device for any purpose other than its specified intended use WARNING IQvitals is
53. nnects to the BP Simulator in same way BP Calibration Check Procedure e Set BP Simulator to 120 80 mmHg Refer to the usage instructions provided with the BP simulator used for this procedure e Click Start BP Meas and wait for measurement to complete The Test Program should report a BP result within 5 mmHg of the simulator setting see picture e Ifitis determined the device is out of tolerance replace Main Board Note All testing assumes a properly functional and calibrated test equipment The IQvitals has been tested with the Fluke Biomedical BP Pump2 simulator BP simulator behavior can vary from manufacturer to manufacturer Click Start BP Meas OvitalkpcService Version 0 1 lQvitals PC Connected SpO2 Code 302 Set 0 PR Code 302 E Temp Normal Code 302 Set Temp Monitor Set Temp Normal BP 121 79 mmHg Start BP Meas Stop BP Mess Cuff 0 0 mm Hg Start BP Cal Stop BP Cal BP Status OF Weight Power Mains Ensure reading is within specifications Midmark Corporation 2013 Revised 08 2013 B 13 Cuff Pressure Calibration Check e Click Start BP Cal e Set the BP Simulator to Pressure Gauge mode and inflate it to 200 mmHg If the simulator does not have a built in pump then use a hand bulb and a calibrated manometer to inflate it to 200 mmHg e Wait for pressure to reach 200 mmHg then observe the pressure values on the BP simulator and Test Program e Ensure tha
54. ocuments My Network Places Details Install QvitalsUSBInstaller Install QvitalsUSBinstaller 27 Maul iy Dis Ee File Edit view Favorites Tools Help Step 1 Open the IQuitalsUSBinstaller folder Double click on IQvitalsUSBlInstaller exe This is a quiet installa Q CD D pO search E Folders E gt E Folder sync tion procedure and no pop up message will appear when Address es En installation is complete fs a a x a x File and Folder Tasks a 1QvitalsService Program pen Touch Panel Calibration Make a new Folder E Publish this folder to the gt rm Web eu IQvitalepcService Program me IOvitalsUSBInstaller Ea Share this folder Note It is only necessary to install IQvitalsUSBlinstaller if you are using a USB connection to connect to the 1Qvitals PC device QvitalsUSBlInstaller is not needed when using the serial con nection to connect to the IQvitals PC device Other Places ig My Computer Lj My Documents G Shared Documents J My Network Places Details TP204 Rev A Midmark Corporation 2013 Revised 08 2013 B 4 Install IQvuitalsUSBlinstaller continued Install IQuitals IQvitalsPC USB Service Kit RE File Edit View Favorite Tools He Step 1 To confirm that the driver is installed ee P k Search 7 Fold ET Fold Connect the IQvitals PC to a computer using a mini Q D Po seach Py reer KA Folder Sync USB connection and po
55. ower supply is lit No power to wall outlet Check wall outlet with a known working power supply Green LED on power supply is lit Bad power supply Check wall outlet with a known working power supply Power supply cable is firmly inserted in the power connector on the back of the device Device won t start Screen stays black on off switch does not illuminate Power supply not fully connected to device A 4 Battery Charging Light on the front of the device is lit green See notes above or refer to the Operation Manual e On off button on the front of the device is lit green Battery is dead Reconnect device to mains power Power cycle the device Device is not powered on Midmark Corporation 2013 Revised 08 2013 DL K Issue Error Code Probable Cause Device won t start continued Device won t start Screen is white Midmark start up banner never displayed Device won t start Screen is frozen at Midmark start up banner or home screen Device won t start Midmark start up banner is displayed and then the screen becomes white Device immediately powers off when disconnected from mains Internal problem Internal problem Internal problem Internal problem Battery is fully discharged Replace I O Board likely Power Switch which is part of the Front Bezel possible or Main Board less likely Power cycle the device Reseat display cable
56. pura or neuropathy In addition be sure that the blood pressure hose does not become kinked during a measurement If left unattended this could result in sustained pressure in the blood pressure cuff WARNING BATTERY HANDLING IQvitals contains a lithium ion battery The following precautions should be taken regarding these batteries e Do not immerse in water e Do not heat or throw in fire e Do not leave in conditions over 60 C or in a heated car e Do not attempt to crush or drop e Only use the battery with the IQvitals device e Follow the instructions in the Disposal section of the devices Operation Manual when any IQvitals device is taken out of service vi TP204 Rev A Cautions Review the following information to avoid damage to the device and to ensure proper operation Caution Familiarize yourself thoroughly with the operational proce dures of the device prior to use Caution Substitution of components different from those supplied could result in measurement error Caution Do not operate the IQuitals device near high frequency emissions e g microwaves Caution The IQvitals device is intended for indoor use only The device and its accessories are not intended to be steril ized by any method Attempting to do so may permanently damage the equipment Caution In case of malfunction call the Midmark Support Serv
57. r device to isolate problem If problem is device related replace 1 0 Board more likely or Main Board less likely Midmark Corporation 2013 Revised 08 2013 A 15 DL Issue Error Code Probable Cause Scale cable not attached to device e Check scale cable connection e Confirm that the Table Scale feature is Midmark 625 with Qscale feature not enabled enabled via the Settings menu device is configured to communicate with Fairbanks scale instead e Refer to the Operation Manual for Settings information ae emar GAS EXAM table Out of Range weight is reported e Is patient less than 30 or greater than 600 Ibs e Check scale cable connection e Test with a known working scale or different Internal problem device to isolate problem e If problem is device related replace l O Board more likely or Main Board less likely Midmark Corporation 2013 Revised 08 2013 A 16 DL Printing Issues An optional external thermal printer purchased from Midmark can used with the IQvitals touchscreen device The thermal printer technology heats the paper to create the image rather than employing an ink cartridge and receives its power directly from the IQvitals device The IQvitals PC does not support a thermal printer Periodic thermal printer accuracy check e The thermal printer does not need calibration e A periodic functional check is warranted See section B of this Service M
58. r lQvitalspcService Test Program depending on the device model number e SpQOo2 Finger sensor Test Set up Note This procedure requires the Test Program to be installed For installation instructions see section I Qvitals IQvitalsoc USB Service Tools Kit e Connect IQuitals touchscreen and or I Qvitals PC to the simulator using an SpOo finger sensor see picture e Ensure that the SpO2 simulator is set to Nellcor mode e Set the SpO gt simulator to 96 SpO and 75 PR e For an lQvitals touchscreen device run the lQvitalsService Test Program e For an lQvitals PC device run the QvitalsocService Test Program on a PC Note IQuitals touchscreen device connects to the SpO2 simulator in same way Midmark Corporation 2013 Revised 08 2013 B 1 7 lt L gt O na wv N A SpO2 Calibration Check Procedure Make sure that the SpO2 and BP codes in the Test Program display change from Code 302 to a numeric reading when connected see pictures Compare the SpO2 and PR readings in the Test Program to the 96 SpO 2 and 75 PR on the SpO simulator display There should be a difference of no greater than 2 for the SpO2 parameter and 5 bpm for PR parameter If the readings are out of tolerance there may be a difference between the SpO2 simulator and the IQvitals processing of the SpO signal Confirm that the SpO2 sensor is properly aligned on the SpO92 simulator s finger If it is determined th
59. rder fault SpO 314 Weak signal SpO 315 Probe fault MON 332 Monitor fault TP204 Rev A Midmark Corporation 2013 Revised 08 2013 A 3 Power Issues The lQvitals devices use an external mains power supply Each device contains a rechargeable lithium ion battery that is automatically recharged when the device is connected to mains The device s power switch is on the front of the device When the device is on the on off switch is lit green The Battery Charging Light is also on the front of the device It indicates the charging status e solid green device is on mains power and battery is charged e blinking green device is on mains power and battery is charging e off device is not on mains power and battery is not charging The IlQvitals device will run on battery power for approximately 8 hours longer for the IQvitals PC device The battery takes about 4 hours to recharge from a fully depleted state A Battery Low message will be reported when the battery is nearly depleted approximately 40 remaining battery power The device automatically shuts itself off when the battery is too low to function The battery should last for 2 3 years under normal use and can be replaced via a dedicated access door on the back of the device Caution A N The device should only be used with the power supply and battery that are listed in the Operation Manual Issue Error Code Probable Cause e Green LED on p
60. re coils back next to the pump and is also secured by the tie wraps Install IQvitals Main Board Service Kit Step 12 Center the pump over the outline on the new board Remove the paper from the stabilizer pad Midmark Corporation 2013 Revised 08 2013 D 33 lt gt O x wz N A Install IQvitals Main Board Service Kit Step 14 To move the valve from the current main board to the new main board unplug it from the old board Install IQvitals Main Board Service Kit Step 15 Cut and discard the tie wrap that holds it Install IQuitals Main Board Service Kit Step 16 Pull firmly on the valve Install IQuitals Main Board Service Kit Step 17 Remove the adhesive pad from the bottom of the new valve Install IQuitals Main Board Service Kit Step 18 Insert one new tie wrap into the new main board Note Press the tie wrap against the bottom of the main board while tightening to avoid having extra slack Install IQvitals Main Board Service Kit Step 19 Plug the valve into the connector Install IQuitals Main Board Service Kit Step 20 Twist several times to wrap the two wires securely together Install IQvuitals Main Board Service Kit Step 22 Secure valve and wire with the tie wrap Install IQvitals Main Board Service Kit Step 21 Loop the twisted wires once around the front of the valve while a
61. should not be incinerated crushed disassembled or exposed to extreme heat See Warnings at the start of this service manual for further precautions Do not put the lithium ion battery in a refuse container Lithium batteries and electronic components should be recycled appropriately Contact your local waste disposal agency for guidance on proper recycling or disposal Midmark Corporation 2013 Revised 08 2013 IX Troubleshooting Midmark Corporation 2013 Revised 08 2013 Device Description lQvitals The IQvitals device contains a Main Board an I O Board and a Processor Board The Main Board contains signal acquisition and power management circuitry The l O Board contains data port connectors The Processor Board runs both signal analysis software to generate the patient s physiological readings and user interface software to display the patient s readings and trend them over time It also contains an SD card which is used to store the patient s readings and the device settings lAvitals PC The IQvitals PC device contains a Main Board and an I O Board but no Processor Board In this case the signal analysis software runs as part of the Qmanager software package on the clinician s workstation Both devices are powered from either an external medical grade mains supply or an internal rechargeable lithium ion battery Both devices can connect to select digital scales Both devices are avail
62. surement started when probe is removed from the probe well Internal problem Temperature measurement starts even though the probe is in the probe well Internal problem TEMP 302 Unplugged Probe unplugged Midmark Corporation 2013 Revised 08 2013 Refer to Operation Manual for proper probe placement Verify correct temperature measurement with a calibrated water bath Test with a known working probe Test with a known working probe Make sure the probe is threaded through the cord guide on the back of the device Check probe and cable for damage Test with a known working probe Perform Temperature Calibration Check See Section B of this Service Manual Check that probe is firmly connected to the device Test with a known working probe Test with a known working probe If problem persists check connectors between l O Board and Main Board for physical damage and replace board s if needed possible Or replace probe well switch which is part of the Temp Assembly less likely Reinsert probe into well power cycle the device and retest If problem persists replace probe well switch which is part of the Temp Assembly most likely or O Board possible Check that probe is firmly connected to the device Test with a known working probe DL K DL Issue Error Code Probable Cause TEMP 304 n e Verify correct temperature measurement with a Temp too high Ie aparare Tegan Wer
63. t they differ by no more than 5 mmHg e If it is determined the device is out of tolerance replace Main Board e Click Stop BP Cal when finished Note All testing assumes a properly functional and calibrated test equipment The IQvitals has been tested with the Fluke Biomedical BP Pump2 simulator BP simulator behavior can vary from manufacturer to manufacturer Before starting the BP simulator click Start BP Cal tOvitalspcService Version 0 1 lOvitals PC Connected Exit SpO Code 30 Comm Port Set PR Code 302 _S t a Temp Normal Code 302 Set Temp Monitor Set Temp Normal BP Cal Mode Start BP Meas Stop BP Meas Cuff 0 0 mm Hg Start BP Cal Stop BP Cal BP Status OK Weight Power Mains TP204 Rev A Compare the Test Program reading to the BP simulator once the simulator reaches 200 mmHg Midmark Corporation 2013 Revised 08 2013 B 14 Leak Rate Calibration Check e Click Start BP Cal e Set the BP Simulator to Pressure Gauge mode and inflate it to 200 mmHg If the simulator does not have a built in pump then use a hand bulb and calibrated manometer to inflate it to 200 mmHg e Allow pressure to reach 200 mmHg and wait 30 seconds for the pressure to stabilize e Watch the pressure value for a full minute and ensure that the Qvitals touchscreen and or I Qvitals PC pressure reading does not drop by more than 5 mmHg see picture e Ifthe leak rate
64. ttaching it to the main board by means of the adhesive pad on the new main board Midmark Corporation 2013 Revised 08 2013 D 34 Install IQuitals Main Board Service Kit Step 23 Attach the NIBP manifold by connecting it to both valves the pump the main board and the input panel Install IQvuitals Main Board Service Kit Step 24 Attach the processor board to the new main board using the three screws Note Be careful to line up pins exactly lt gt O a wz N A Note The screw is beneath the manifold Midmark Corporation 2013 Revised 08 2013 D 3 5 TP204 Rev A IQuitals Processor Board Service Kit Part 183 6720 Install IQvitals Processor Board Service Kit Step 1 Detach the processor board from the main board by removing all three screws and pulling the two boards gently apart Note The screw is beneath the manifold Note Touch panel calibration is required after the replacement of processor board Refer to the IQvitals Touch Panel Calibration section of this Service Manual Midmark Corporation 2013 Revised 08 2013 D 36 Install IQuitals Main Board Service Kit Step 2 Attach the new processor board to the main board using the three screws Note Be careful to line up pins exactly IQuitals SD Card Assembly Part 181 6761 Install IQvitals SD Card Assembly Step 1 To replace th
65. unscrewing the two screws removing the input panel and screwing the input panel onto the new main board Install IQuitals Main Board Service Kit Step 5 Remove the NIBP pump from the main board by first unplugging the pump wire Install IQvuitals Main Board Service Kit Step 6 Cut and discard the two tie wraps that hold the NIBP pump Dita g Midmark Corporation 2013 Revised 08 2013 D 32 Install IQvuitals Main Board Service Kit Step 3 Disconnect the manifold from all its connections and set it aside Install IQvuitals Main Board Service Kit Step 7 Pull firmly on the pump to remove it from the adhesive stabilizer pad and main board Install IQuitals Main Board Service Kit Step 8 Remove the adhesive stabilizer pad from the bottom of the pump lt gt O oO wz N A Install IQuitals Main Board Service Kit Step 9 Install the NIBP pump on the new main board by first inserting two new tie wraps Note Press the tie wraps against the bottom of the main board while tightening to avoid having extra slack Install IQuitals Main Board Service Kit Step 10 Plug the pump into the connector Install IQvitals Main Board Service Kit Step 13 Secure the pump with tie wraps Install IQvitals Main Board Service Kit Step 11 Twist several times to wrap the two pump wires together Note Ensure that the wi
66. urement technique e Retake measurement BP readings seem low or high e Test with a known working device e Test with a known working device Internal problem e Check accuracy of BP circuit See Section B of this Service Manual e Select the BP Start pressure button that is Initial inflation pressure too low 30 mmHg above the patient s systolic value to avoid double pumping Measurement taking too long Ask patient to remain still Patient motion e Retake measurement Arrhythmia or valvular defect Measure on opposite arm Ask patient to remain still Too much patient movement e Retake measurement e Apply the cuff to the opposite arm where Patients pulse signal has persistent variability due variability may be reduced NIBP 305 Artifact to arrhythmia or valvular problem e Retake measurement Midmark Corporation 2013 Revised 08 2013 A 7 K Issue Error Code Probable Cause NIBP 306 Hardware failure NIBP 309 e Instruct patient to remain still Cuff pressure was too high Overpressure e Retake measurement NIBP 310 e Check the BP hose for damage or kinks l BP hose is constricted Blocked line e Retake measurement Midmark Corporation 2013 Revised 08 2013 Internal problem A 8 Power cycle the device If problem persists connect device to Test Harness and power up See Section B of this Service Manual If problem is persistent it will occur whe
67. wer the unit on Address E E QvitalsUSBInstaller e Two notices will appear only the first time at the bot tom task bar 1 Found New Hardware then 2 IQvuitals Device File and Folder Tasks mi Rename this File ir Move this file QwitalsUSBlnstaller exe setup ini a P Driver Installation Utility Configuration Settings A Copy this File Silicon Laboratories Inc 1 KB g Publish this file to the Web eee x siusbxp cat SIUSBXp inf im E mail this File f Security Catalog gt Setup Information X Delete this file f 9kE J 2k Other Places a Removable Disk E LJ My Documents CA Shared Documents ie ee Double click SJ My Network Places Details TP204 Rev A Midmark Corporation 2013 Revised 08 2013 B 5 Install IQuitalspcService Test Program Install IQuitalspcService Test Program Removable Disk E Step 1 Copy the lQvitalspcService Program Folder File Edit View Favorites Tools Help a EJ onto the computer s hard drive O Baci Q P po Search ey Folders Bak fa Folder Sync PR v SE J lOvitalsService Program OvitalspcService Program CJ TQvitalsUSBInstaller Address TQvitals Touch Panel Calibration Program File and Folder Tasks i Ci Rename this folder iy Move this folder A Copy this folder Publish this folder to the Web kgf Share this folder A E mail this Folder s Files X Delete this Folder Other Places Copy to

004-xxxx-00 -Service Manual: Product name

Contents

Download Pdf Manuals

Related Search

Related Contents