president popcorn machine service manual
Contents
1. 208 Volts 230 Volts 240 Volts 400 Volts MARCH 2000 120 Volts 230 Volts 120 Volts 230 Volts 13 PR EPR TEPR20 32 48 M A E S 208 Volts 0 Volts 230 Volts 0 Volts 240 Volts 0 Volts 230 Volts same pole 0 Volts same pole BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S Problem in kettle Remove kettle see Service Section for removal instructions Check for short circuits inside the kettle If wires must be replaced be sure to use nickel wire supplied Cretors Conventional copper or nickel plated stove wire will have limited life Make a visual check for broken loose burned or heat damaged wires If there are no obvious broken or loose wires shorting out on the kettle the elements must be checked Perform a continuity test on the elements It is possible that one of the elements has burned through its insulation and casing and is shorting out directly to the kettle bottom Continuity test Remove the nickel buss bars that connect the electrical terminals on the heat elements Check each element between the following points MARCH 2000 Terminal to terminal Continuity functioning properly No continuity burned element replace First terminal to element case Continuity to case from terminal indicates a grounded element replace No continuity functioning properl Second terminal to element Continuity to case from terminal indicates a case grounded element replace No continu2. hour per popper First popper 8350 watts second popper 6800 watts 28 D x 72 W x 73 H 71 cm D x 182 cm W x 185 cm H 645 lbs 293 kg 5 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S VI CONTROL SWITCHES KETTLE HEAT Turns the kettle heat On Off AGITATOR Turns the stirrer blade motor On Off EXHAUST Turns exhaust blower On Off CORNDITIONER Turns the cornditioner blower and heat On Off LIGHTS Turns interior lights On Off OIL Provides power to the oil pump DELIVERY Initiates the pump cycle CIRCUIT BREAKER Push to reset provides protection to all circuits except the kettle VII INSTALLATION INSTRUCTIONS 1 Location Choose a location for your Cretors popcorn machine to maximize the ease of operation and maintenance procedures Check your local building and fire codes for location restrictions 2 Power Supply A Check the nameplate to determine the required power supply AN Connect your popcorn popper only to the correct power source Failure to do so may result in personal injury or death and may damage your popper B C Cretors and Company recommends dedicated circuits for the President model popcorn machine The President model poppers require a dedicated circuit to avoid voltage drop in the supply wiring Check your local electrical codes regarding fuse or circuit breaker requirements AN Make certain your popcorn machine is properly grounded Failure to do so may result in damage to your equip
3. listed below Please provide model and serial number when requesting additional copies of this manual There will be a nominal charge for additional copies Cretors guarantees this machine to be free of defects in parts materials and workmanship for one year Please take this time to fill out the factory registration card and return it to the factory to activate your warranty If you have any questions concerning the Cretors warranty please contact your local dealer or the Customer Service department at C Cretors and Company iins 8 CR TORS MARCH 2000 23 BEGIN SERIAL NO 00000000
4. removal A To remove the kettle cover remove the wing nuts washers and anchor lugs holding the cover onto the kettle shield Next remove the kettle shield brackets screws and wing nuts holding the kettle shield and apron onto the kettle B The agitator assembly is disassembled by removing the anti pak pin going through the top of the stirrer blade Lift off the stirrer blade Place kettle in dump position and slide the clutch dog and shaft out from the bottom of the pan If shaft will not easily drop out use a hammer and lightly tap on the shaft to break it free If it is apparent that the clutch dog and shaft cannot be removed leave it in place however at sometime in the future it will be necessary to remove and replace the entire pan center and clutch dog assembly This must be done before the clutch dog shaft becomes hard to turn when the shaft becomes hard to turn the agitator motor will be overloaded and damaged C Clean all parts thoroughly making sure to use Cretors Kettle Cleaner Do not use any harsh abrasives or cleaning material Pay particular attention to the interior of the blade center Some popping oils will carbonize and build up on the interior of the blade center and create a tight fit on the pan center normal clearance is 1 8 3 mm When this happens oil will wick up the narrow gap and leak down the clutch dog shaft and give the appearance that the kettle is leaking oil In extreme cases the carbon will cause th
5. 4 D x 60 W x 73 1 4 H 61 cm D x 152 cm W x 186 cm H 425 Ibs 193 kg 4 BEGIN SERIAL NO 00000000 MODEL EPR32E5 Capacity Wattage Dimensions Net Weight MODEL EPR48E5 Capacity Wattage Dimensions Net Weight MODEL TEPR20E6 Capacity Wattage Dimensions Net Weight MODEL TEPR32E6 Capacity Wattage Dimensions Net Weight MODEL TEPR48E6 Capacity Wattage Dimensions Net Weight PR EPR TEPR20 32 48 M A E S PRESIDENT 32 OZ ELECTRIC 5 ENCLOSED TOP 32 oz All Steel Kettle 640 one ounce servings per hour 6650 watts 24 D x 60 W x 73 1 4 H 61 cm D x 152 cm W x 186 cm H 425 Ibs 193 kg PRESIDENT48 OZ ELECTRIC 5 ENCLOSED TOP 48 oz All Steel Kettle 960 one ounce servings per hour 8200 watts 24 D x 60 W x 73 1 4 H 61 cm D x 152 cm W x 186 cm H 425 Ibs 193 kg TWIN PRESIDENT 20 OZ ELECTRIC 6 ENCLOSED TOP 20 oz All Steel Kettles 400 one ounce servings per hour per popper First popper 5250 watts second popper 3700 watts 28 D x 72 W x 73 H 71 cm D x 182 cm W x 185 cm H 645 Ibs 293 kg TWIN PRESIDENT 32 OZ ELECTRIC 6 ENCLOSED TOP 2 320Z All Steel Kettles 640 one ounce servings per hour per popper First popper 6800 watts second popper 5250 watts 28 D x 72 W x 73 H 71 cm D x 182 cm W x 185 cm H 645 lbs 293 kg TWIN PRESIDENT 48 OZ ELECTRIC 6 ENCLOSED TOP 2 48 oz All Steel Kettles 960 one ounce servings per
6. ERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S D Remove the two bolts on the side of the aluminum pan legs A E Using proper lifting techniques remove the kettle by lifting it straight up F Turn the kettle upside down and remove the bolts that hold the dump handle and retainer and lift the retainer off the kettle G When removing nuts and spacers from the threaded studs on the bottom of the pan do not wipe off the silver lubricant Without this lubricant NEVER SEEZ the nuts may freeze on the studs and cause the studs to break when the nuts are turned in an attempt to remove them H When reassembling the kettle be sure that all electrical connections are secure A loose connection can heat up and burn off the wires Tighten the bolts that hold the retainer except for the four bolts around the pan leg plate I Set the kettle back in place and replace the two bolts in the pan legs J Locate the kettle so that the clutch dog lines up with the motor drive head and tighten the two front bolts that hold the pan leg plate then tip the kettle and tighten the other two bolts K Turn on the agitator motor and dump the kettle If the drive head does not engage and disengage freely readjust the kettle 4 Kettle Spring Adjustment The purpose of the kettle counter balance springs is to reduce the force required to dump the kettle The spring collars are held in place by set screws that fit into holes drilled on the bottom of the
7. PR EPR TEPR20 32 48 M A E S PE TORS PRESIDENT POPCORN MACHINE SERVICE MANUAL 120 208 240 Volt Single and Three Phase 60 Hz 100 200 Volt Single Phase 60 Hz 230 Volt 230 380 Volt Single and Three Phase 50 Hz 400 Volt Three Phase 50 Hz A READ and UNDERSTAND these servicing and safety instructions before servicing this popcorn machine MARCH 2000 1 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S SAFETY FIRST maintenance of your Cretors popcorn machine The manual must be read and understood before installing or maintaining this equipment or equivalent training must be provided The information in this manual is essential for the safe installation and The employer shall instruct each employee in the recognition and avoidance of unsafe conditions and the regulations applicable to his work environment to control or eliminate any hazards or other exposure to illness or injury Ref 29 CFR 1926 20 b 4 a 2 gt conflict exists between the safety procedures contained in this manual and the rules of a using company the more stringent rule should take precedence i It is understood that safety rules within individual companies vary If a MARCH 2000 2 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S I INTRODUCTION This manual is filled vvith time saving and money saving information regarding your Cretors popcorn machine There is nothing hovvever more important than
8. cross shaft The spring collars have five holes that the spring fits into By turning the collar around all five of the holes may be used for spring tension adjustment When correctly adjusted the springs will neutralize the weight of the kettle To set the springs raise the kettle to a point where it is balanced The long leg of the 1902 spring should be just beginning to touch the bar on the bottom edge of the hinge casting and the 1903 spring will begin to move away from the bar If the springs press against the bar too soon the kettle will seem lighter but the springs are fighting each other This condition will shorten the life of the springs An important part of this assembly are the two washers between the 1902 spring and the plate welded to the cross shaft They act as both bearings and spacers without them the spring may have a short life MARCH 2000 9 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S MARCH 2000 10 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S IX TROUBLE SHOOTING 1 Problem Popping is slow Slow popping on first two cycles is normal QUESTION Were the correct amounts of corn and oil used Refer to the chart in the operating section for the correct quantities QUESTION Does the kettle indicator light go out more than 30 seconds before the corn finishes popping YES Temperature set too low See section on how to adjust temperature CAUTION If the corn has dried out it may not finis
9. d and understood this manual Failure to do so may result in serious injury or death 2 Do not attempt to operate your Cretors popcorn machine unless the installation instructions have been strictly adhered to Failure to do so may result in serious injury or death 3 Operate your popcorn machine only if it is in sanitary condition GANITATION INSTRUCTIONS Failure to do so may result in illness to your customers 4 Always turn OFF the KETTLE HEAT switch when not popping corn Failure to do so will cause oil to stain the kettle possibly resulting in an unsanitary condition It may also cause a flash fire if oil is added to a kettle left unattended with the heat on resulting in serious burns or death a i iol 5 To operate your Cretors popcorn popping machine A Fill the corn drawer with corn all models a Fill the salt box and hang it on the inside edge of the corn drawer Q Connect and adjust the pump as explained in the installation instructions and preheat the popping oil until liquid if necessary Ss Fill the corn measure with corn and the salt measure with salt and empty these into the kettle When making sugar corn add the correct amount of sugar rather than salt with the measure of corn E Rotate the kettle lid closed using the counter weight as a handle Avoid contact with the kettle Contact with a hot popping kettle may result in serious burns or scalds CAUTION Always add corn to the ket
10. e blade center to grip the pan center and turn it This will loosen the pan center and a serious oil leak will occur When reassembling lightly coat the clutch dog shaft with moly grease or a comparable high temperature lubricant D Reassemble cover in reverse order following the directions above 3 Cabinet A Remove and empty the waste clean out drawer daily or whenever it is full Under AN heavy use this may need to be done more often Failure to empty the drawer and clean cabinet may result in a fire hazard due to restricted air flow B The cabinet glass and cabinet base can be cleaned with any good grade glass or household cleaner suitable for glass and plastic surfaces The inside of the cabinet can be cleaned with the same cleaner as the outside if it is the type that has a cleaning agent to cut the oil remaining from the popping operation and it is acceptable for food contact surfaces MARCH 2000 21 BEGIN SERIAL NO 00000000 C PR EPR TEPR20 32 48 M A E S The perforated screen of the 60 and 72 cabinets should be removed at least weekly or more often if needed to thoroughly clean the air chamber beneath of salt and small bits of corn which come through the air holes The corn and scraps may be swept into the hot air well in the center of the bin Remove the clean out drawer from under the popper case bottom and slide it under the hot air well then pull out the clean out slide All the scrap will fall into the scrap dra
11. e 60 and 72 cabinets is the same and consist of a blower heating element and a thermostat mounted in a removable box The cornditioner circulates hot air through the popper case to keep popped corn hot and crisp An indicator light next to the cornditioner switch indicates when there is power to the circuit With the power connected turn the cornditioner ON QUESTION Is the indicator light ON and no air being delivered A Cornditioner screen blocked clear passageway B Check connections to blower MARCH 2000 15 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S C Replace blovver MARCH 2000 16 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S QUESTION Is the indicator light ON and cool air is being supplied A Check thermostat replace The maximum air output temperature is approximately 140 F 60 C The thermostat is installed as a safety device and is not adjustable B Check heat element replace QUESTION Is the indicator light ON and air from blower too hot A Thermostat stuck in ON position replace B Blower not operating properly replace 5 Problem Exhaust Odors A Wash grease filter B Replace charcoal media in the charcoal filter box 6 Pump Refer to pump service manual MARCH 2000 17 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S X OPERATING INSTRUCTIONS 1 Do not attempt to operate your Cretors popcorn machine until you have rea
12. er is empty replace with new full container of oil MARCH 2000 19 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S J Repeat steps D G as desired adding corn to the corn drawer and salt to the salt box as necessary NOTE The ideal time for maximum volume is between 2 3 4 to 3 1 2 minutes from the time the corn is placed into the kettle until the time it is dumped Check the popping time after several popping cycles Reduce the charge of raw corn if the time is more than 3 1 2 minutes and increase the charge if the time is less than 2 1 2 minutes per popping K Follow the recommended sanitation procedures XI SANITATION INSTRUCTIONS Be certain the machine is turned off and power is unplugged before sanitizing this machine unless a specific cleaning procedure requires power to the machine Failure to do so could result in injury or death Do not clean heated surfaces until they have been given sufficient time to cool Failure to do so may result in serious burns or scalds gt gt 1 Popping Kettle A Do not immerse an assembled pan in water This will damage the electrical components and my cause short circuits resulting in electrical shock hazard if power is applied gt B Do not use steel wool or other similar abrasives to clean the kettle as they will ruin the kettle by removing the nickel plating N Do not attempt to clean the kettle with power connected unless you are boiling the CKC cleaning comp
13. h popping at normal temperatures and the light may appear to go out early DO NOT ADJUST KETTLE TEMPERATURE BASED ON POOR QUALITY CORN the popping cycle If set too high over 500 F or 260 C the kettle can become a serious fire hazard CAUTION Do not adjust the temperature so high that the pan smokes at the end of N O A Voltage may be low check voltage at circuit breaker with kettle heat ON Extension cords or inadequate wiring will provide full voltage if no load is applied Once the kettle heat and auxiliaries are turned on the voltage may drop 5 to 10 volts B If indicator light stays ON for the full popping cycle one element in a multi element pan may be have failed Use an ammeter to diagnose Place the ammeter around the black or red lead to the popper kettle The following current draws are normal KETTLE SIZE AMPS 200V AMPS 208V AMPS 230V AMPS 240V 20 oz 125 13 0 10 8 11 2 32 oz 19 6 20 4 17 0 17 7 48 oz 26 8 28 1 23 4 24 4 380V Place the ammeter around the black or brown lead to the popper kettle MARCH 2000 11 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S KETTLE SIZE AMPS 380V 32 oz Brown Black 8 9 48 oz 11 8 2 A low reading indicates a problem in the kettle One or more of the heat elements may not be functioning properly If the element is not functioning the possible causes are either that the element has burned out or a lead wire has burned off
14. ity functioning properl 20 oz 208V elements 9000 Watt 48 1 Q 1800 Watt 24 0 Q 2700 Watt 16 0 Q total 20 oz 240V elements 900 Watt 64 0 Q 1800 VVatt 32 0 Q 2700 Watt 21 3 Q total 32 oz 208V elements 750 Watt 57 7 Q 1500 Watt 28 8 Q 2000 Watt 21 6 Q 4250 Watt 10 7 Q total 32 oz 240V elements 750 Watt 76 8 Q 1500 Watt 33 4 Q 2000 VVatt 28 8 Q 4250 Watt 13 6 Q total 14 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S 48 oz 208V elements 750 Watt 57 7 Q 1250 Watt 34 7 Q 1800 Watt 24 0 Q 2000 Watt 21 6 Q 5800 Watt 7 5 Q total 48 oz 240V elements 750 Watt 76 8 Q 1250 Watt 46 10 1800 Watt 32 0Q 2000 Watt 28 80 5800 Watt 9 9 Q total Replace failed heat elements with identical units available from your local dealer or from Cretors Reassemble and reinstall kettle assembly onto the machine 3 Problem Corn Burns QUESTION Is the agitator working YES A Check to be certain the stirrer blade is on the bottom of the pan and is stirring the corn B Were the correct amounts of corn and oil used See operation section for correct amounts C Temperature set too high adjust temperature NO A Check motor connections loose wire B Motor bad replace 4 Problem in Cornditioner The President series of machines has two cabinet sizes 60 and 72 The cornditioner heat system in th
15. ment or present a shock hazard 3 Connecting Machine to Power Supply AN A Perform work only on de energized circuits Failure to do so may lead to electrical shock resulting in personal injury or death B Make certain that power supply circuit breakers are in the OFF position C Push the plug completely into the receptacle If the cord has a twist lock plug be sure to turn to lock in position MARCH 2000 6 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S 4 Pump Installation Refer to the instruction manual supplied vvith the pump to be installed in the machine VIII SERVICE INSTRUCTIONS following diagnostic checks and if necessary corresponding adjustments and repairs Many of the following procedures present an electrical shock hazard and can cause serious injury or death In the case of improper operation qualified personnel only should perform the 1 Parts When ordering parts refer to the attached parts diagram Always supply the serial number model number and voltage of your popcorn machine 2 Kettle Temperature Control THERMOSTAT OPERATION The thermostat is installed as a safety device to prevent overheating of the kettle if the machine should be left unattended momentarily while in operation The kettle indicator light will shut off when the kettle heat has been shut off by the thermostat This should be 15 to 30 seconds before the corn stops popping and the kettle is dumped If the indicator ligh
16. one of the element terminals due to a loose connection In either case the kettle must be removed and the problem identified See service section for kettle removal instructions 2 Problem Kettle Will Not Heat QUESTION Do any of the other components work motor light etc NO Check power supply Is machine plugged in Is the receptacle live Is machine plugged into the proper voltage Measure with voltmeter and compare to specification on nameplate of machine NWS Do not attempt electrical repairs on the power supply circuit unless you are qualified to do so The electrical shock associated with line voltages can cause serious injury or death YES A Problem is in machine AN The following procedures are performed with the power ON As with any electrical repairs there is a shock hazard present Check the relay The President uses a relay to control the power to the popper pan heat elements To check the relay perform the following operations a To gain access to the relay remove the switch plate b Using a voltmeter check the power to the relay coil these are the small terminals in the center c At room temperature the temperature control should be calling for heat and providing power to the relay If the coil reading is not approximately d If the coil reading is approximately Elements Coil Relay BAD top to bottom GOOD 200 Volts 100 Volts 200 Volts 0 Volts MARCH 2000 12 BEGIN SERIAL NO 00000000
17. ound to clean the inside of the kettle in step G Do not attempt to clean a hot kettle Failure to do so may result in serious burns or scalds B The kettle has a polished nickel finish and is very easy to clean if oil is not allowed to burn on it After the final popping the best practice is to wait until the oil just begins to solidify then take a cotton towel or absorbent rag and wipe the kettle Once the oil is allowed to completely solidify it can become more difficult to remove We recommend coconut oil for your Cretors popper it will not stick or burn as easily as other oils Hi The outside of the kettle should be cleaned with Cretors Outside Kettle Cleaner COC periodically to remove popping oil that may become baked on MARCH 2000 20 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S G Clean the interior of the kettle every week with CRC cleaning compound This will prevent the accumulation of carbon on the bottom and internal sides of the kettle When using CKC cleaning compound in the kettle do not fill the kettle with more than 3 4 high of water inside the kettle Heat the water to boiling and turn off the kettle heat don t boil the kettle dry If the kettle has been overheated or oils that tend to carbonize are used the normal cleaning procedures may not suffice Increase frequency as needed H To properly clean the kettle it is necessary to remove cover and agitator assembly 2 Kettle cover and agitator
18. screw all the way in or out This will render the could possibly cause a flash fire if oil is put into the pan H If no pyrometer is available the thermostat may be adjusted by observing the operation of the indicator light as described in the Thermostat Operation section Adjust the thermostat so that the kettle heat is turned off 15 to 30 seconds before the corn finishes popping and the kettle is dumped CAUTION Ifthe corn has dried out it may not finish popping at normal temperatures and the light may appear to go out early DO NOT ADJUST KETTLE A TEMPERATURE BASED ON POOR QUALITY CORN CAUTION Do not adjust the temperature so high that the pan smokes at the end of the popping cycle If set too high over 500 F or 260 C the kettle can become a serious fire hazard I Your final setting should allow the indicator light to cycle off 15 to 30 seconds prior to dumping the kettle J Observe two or three cycles of correct operation to be certain everything is working correctly 3 Kettle Removal To remove the kettle assembly perform the following operations Direct wire kettle A Unplug the popcorn machine from the power supply B Remove the cover on the terminal box between the pan support legs C Disconnect the three power leads observing the color of the wires Correct color code is Left to right BLACK RED WHITE 230 380 BLUE BROWN WHITE on front terminal left to right Black on back terminal MARCH 2000 8 BEGIN S
19. t gt MARCH 2000 3 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S PRODUCT IDENTIFICATION CRETORS POPCORN MACHINE PRESIDENT Models PR20E5 PR32E5 PR48E5 EPR20E5 EPR32E5 EPR48E5 TEPR20E6 TEPR32E6 TEPR48E6 ELECTRICAL SPECIFICATIONS configurations President Models are available in the following Electrical 100 200 Volt Single Phase 60 Cycle 120 208 Volt 120 240 Volt Single and Three Phase 60 Cycle 230 Volt 230 380 Volts Single and Three Phase 50 Cycle MACHINE SPECIFICATIONS MODEL PR20E5 Capacity Wattage Dimensions Net Weight MODEL PR32E5 Capacity Wattage Dimensions Net Weight MODEL PR48E5 Capacity Wattage Dimensions Net Weight MODEL EPR20E5 Capacity Wattage Dimensions Net Weight MARCH 2000 PRESIDENT 20 OZ ELECTRIC 5 OPEN TOP 20 oz All Steel Kettle 400 one ounce servings per hour 5100 watts 31 D x 60 W x 63 H 79 cm D x 152 cm W x 160 cmH 415 lbs 188 kg PRESIDENT 32 OZ ELECTRIC 5 OPEN TOP 32 oz All Steel Kettle 640 one ounce servings per hour 6650 watts 31 D x 60 W x 63 H 79 cm D x 152 cm W x 160 cmH 415 lbs 188 kg PRESIDENT 48 OZ ELECTRIC 5 OPEN TOP 48 oz All Steel Kettle 960 one ounce servings per hour 8200 watts 31 D x 60 W x 63 H 79 cm D x 152 cm W x 160 cm H 415 Ibs 188 kg PRESIDENT 20 OZ ELECTRIC 5 ENCLOSED TOP 20 oz All Steel Kettle 400 one ounce servings per hour 5100 watts 2
20. t goes off more than 30 seconds before the corn finishes popping the temperature is set too low and needs adjustment Repair parts thermostats shipped from the factory have been adjusted to switch off the current to the heating elements when the kettle temperature reaches 410 F 210 C The factory setting should prove satisfactory however each thermostat must be checked after installation to confirm correct operation To adjust the thermostat perform the following operations THERMOSTAT ADJUSTMENT A Locate the plugged thermostat access hole on the side of the kettle retainer and remove the plug B Turn on the kettle heat C Locate pyrometer over thermostat D Set thermostat so that the power to heat elements is cut off at the correct temperature KETTLE SALTED CORN SUGAR CORN 20 OZ 420 F 216 C 380 F 193 C 32 OZ 410 F 210 C 370 F 188 C MARCH 2000 7 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S 48 OZ 410 F 210 370 F 188 C E To adjust thermostat insert a flat blade screwdriver into the slotted adjustment screw and turn COUNTER CLOCKWISE to raise the temperature or CLOCKWISE to lower the temperature a Do not adjust more than one quarter turn at a time One full turn of the adjustment screw equals approximately 110 Fahrenheit 43 C thermostat inoperable and the kettle heat will increase to a dangerous level and i G Do not screw the adjusting
21. the safety aids and vvarnings that are found throughout this document The Safety Alert Symbol is used to identify topics of primary safety concern wherever they appear Furthermore a separate section has been included which deals exclusively with operation and accident prevention If after reviewing this manual anything is unclear or technical problems are encountered contact the dealer from whom you purchased your machine for assistance and if there are any additional questions feel free to contact our Customer Service Department at the address and or phone number listed on the last page of this manual Always have the model and serial number of your machine available to assist in obtaining the correct information II SAFETY ALERT SYMBOL The symbol shown below is used to call your attention to instructions concerning your personal safety and the safety of others Watch this symbol It points out important safety precautions It means ATTENTION Become Alert Your personal safety is involved Read the message that follows and be alert to the risk of personal injury or death D Ill PURPOSE OF MANUAL This instruction manual is intended to familiarize owners with the servicing and safety procedures associated with your Cretors popcorn machine This manual should be kept available to maintenance personnel A person who has not read and understood all operating and safety instructions is not qualified to operate the machine gt g
22. tle before pressing the oil delivery button or adding oil Failure to do so may result in the oil being heated too rapidly resulting in a gt P fire F Turn ON the agitator turn ON the exhaust fan turn ON the kettle heat G Press the delivery button to pump the correct amount of oil into the kettle MARCH 2000 18 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S A NOTE After the first popping the Rettle is hot Avoid contact vvith the Rettle vvhen adding corn or salt Failure to do so may result in serious burns or scalds Measuring instruments have been provided to accurately measure the proper amounts of popcorn salt and oil The correct amount for each popping is SALTED CORN VOLUMETRIC MEASURE Kettle Size Corn Oil Salt 20 oz 6 5 OZ 591 ml 192 ml 32 oz 12 25 oz 1083 ml 360 ml 48 oz 16 5 oz 1475 ml 492 ml SUGAR CORN VOLUMETRIC MEASURE Kettle Corn Oil Sugar 8 25 oz 245 ml 15 25 oz 451 ml 2 75 OZ 614 ml H As the corn pops it will push the lid open When the lid has moved about one and one half inches it will open completely allowing the corn to discharge from the kettle When the corn finishes popping dump the kettle by lifting the large black handle Then when the pan is empty return the kettle to the horizontal position A Avoid contact with the kettle when dumping popped corn Failure to do so may result in serious burns or scalds I When the oil contain
23. wer When through replace the clean out slide and the clean out drawer 4 Pump MARCH 2000 Refer to manual supplied with pump 22 BEGIN SERIAL NO 00000000 PR EPR TEPR20 32 48 M A E S SAFETY FIRST your Cretors popcorn machine The manual must be read and understood before installing operating or maintaining this equipment or equivalent training must be provided The information in this manual is essential for the safe installation and maintenance of The employer shall instruct each employee in the recognition and avoidance of unsafe conditions and the regulations applicable to his work environment to control or eliminate any hazards or other exposure to illness or injury Ref 29 CFR 1926 20 b 4 a 2 gt between the safety procedures contained in this manual and the rules of a using It is understood that safety rules within individual companies vary If a conflict exists company the more stringent rule should take precedence This manual is filled with time saving and money saving information regarding your Cretors popcorn popper There is nothing however more important than the safety aids and warnings found throughout this document If you have any questions contact your local dealer and if there are any additional questions feel free to contact the Customer Service Department at C Cretors and Company Additional copies of this manual can be obtained from C Cretors and Company at the address
Download Pdf Manuals
Related Search