Home

Unità base di un sistema refrigerante MANUALE DI

image

Contents

1. 15 16 INSTALLATION USE AND ASSISTANCE MANUAL Refrigerating system base unit Read carefully before use CONTENTS PRODUCT DESCRIPTION INSTALLATION AND WIRING 2 1 Introduction 2 2 Mechanical connections 2 3 Temperature adjustment and position of the probe 2 4 Ventilation 2 5 Speed adjustment system WIRING CONNECTIONS 3 1 Introduction 3 2 Wiring diagram BASE UNIT ND35H20 ND50H20 WITH LIQUID COOLER 4 1 Installation 4 2 Tecnical data 4 3 wired diagram 1 APPLIANCE DESCRIPTION The refrigerating units are comprised of an R134A evaporating unit a condensing unit and a R134A compressor designed to create capillary refrigerating systems with evaporation temperatures between 25 C and 10 C The compressor can be powered at both 230 V AC and 24 V DC as well as 42 V DC Only the direct current versions V DC have a compressor control unit that is automatically adjusted according to power voltage The compressor is able to operate silently as well as being efficient and safe up to a permanent inclination of 30 The control electronics on DC models only to prevent early compressor breakdowns caused by over frequent thermostat cycles is programmed to create a 3 minute delay between each stop and the subsequent restarting of the compressor itself 2 INSTALLATION 2 1 Introduction The two main parts of the refrigerating unit condenser and evaporating units have been pre loaded with R134A gas in pre
2. 17 OLI 601 96 0 AbT V H A A ATI N A A DI PUOISUI xe ODOLHE AHT 099815 APT PUOISUD XEN oee AZ 0991S ATT 6 9103SISOH In A A Feo A A VA xeu APT umop mo mo APT xew AZI wno AZI mo mo AZI 6 1081590 B119 8q 9U0IZ9 0 1d euorzdo motzeisodut Suns U01399301d Cause pguongdo 22 12 24 V DC and 100 240 V AC Control unit The electronic unit is a multi voltage device It can be used with 12V 24 V DC and 100 240 V AC 50 60Hz systems The maximum voltage for 12V DC systems is 17 V DC while for 24 V DC systems it is 31 5 V DC In case of AC power the maximum voltage is 265 V AC while the minimum is 85 V AC The maximum ambient temperature is 55 C The electronic unit has an incorporated thermal insulation to start and stop the compressor if the temperature of the electronic unit becomes too high 100 C 212 F on the printed circuit Power consumption is limited to 100 W See the data sheet BD50F for details Installation fig 6 Connect the terminal plug from the electronic unit to the compressor terminal Fit the electronic unit on the compressor by snapping the cover over the screw head 1 Power supply fig 6 DC The electronic unit must always be connected directly to the battery poles 2 Connect the plus to and the minus to otherwise the electronic unit will not work The electronic unit is protected against reverse battery connection For protection of the installation a fuse 3 must be fitted to t
3. Unit base di un sistema refrigerante Refrigerating system base unit MANUALE DI INSTALLAZIONE USO ED ASSISTENZA INSTALLATION USE AND ASSISTANCE MANUAL Leggere attentamente prima dell uso Read carefully before use MANUALE DI INSTALLAZIONE USO ED ASSISTENZA Unit base di un sistema refrigerante Leggere attentamente prima dell uso INDICE DESCRIZIONE DEL PRODOTTO INSTALLAZIONE COLLEGAMENTI ELETTRICI 2 1 Introduzione 2 2 Collegamenti meccanici 2 3 Regolazione della temperatura e posizionamento della sonda 2 4 Aerazione 2 5 Sistema di variazione velocita COLLEGAMENTI ELETTRICI 3 1 Introduzione 3 2 Schema elettrico GRUPPO ND35H20 ND50H20 RAFFREDDATO AD ACQUA 4 1 Installazione 4 2 Dati tecnici 4 3 Collegamento elettrico 1 DESCRIZIONE DEL PRODOTTO Le unit refrigeranti sono composte da un unit evaporatrice ad R134A un unit condensatrice ed un compressore ad R134A progettato per la realizzazione di impianti frigoriferi a capillare con temperature di evaporazione comprese tra 25 C e 10 C Il compressore alimentabile sia a 230 Vca sia a 24 Vcc che a 42 Vcc Nelle sole versioni alimentate a corrente continua Vcc presente la centralina elettronica del compressore che si regola automaticamente in base alla tensione di alimentazione Il compressore in grado di funzionare in maniera silenziosa efficiente e sicura fino ad un angolo di inclinazione permanente pari a 30 L elettronica di c
4. elettronica diventi troppo elevata 100 C 212 F sul circuito stampato La potenza assorbita limitata a 100W Vedi la scheda tecnica BD50F per i dettagli Installazione fig 6 Collegare il connettore terminale dell unit elettronica di controllo al terminale del compressore Montare l unit sul compressore incastrando il coperchio sulla testa della vite 1 Alimentazione fig 6 DC L unit elettronica di controllo deve essere sempre collegata direttamente ai poli della batteria 2 Connettere il polo positivo al ed il negativo al diversamente l unit non potr funzionare L unit protetta contro l inversione di polarit Per proteggere l installazione deve essere sempre montato un fusibile 3 sul cavo il pi vicino possibile alla batteria Si raccomanda l uso di un fusibile da 15A per il circuito a 12V e di un fusibile da 7 5A per il circuito a 24V Se si fa uso di interruttore generale 4 esso va dimensionato per un minimo di 20A Le dimensioni dei cavi raccomandate in fig 7 devono essere rispettate Evitare ulteriori connessioni al sistema di alimentazione per evitare che eventuali cadute di tensione influiscano sulle impostazioni per la protezione della batteria AC I cavi elettrici devono essere collegati ai morsetti contrassegnati L ed N sulla unit elettronica Tensione nominale da 100 a 240 V AC 50 60Hz Interruttore di sicurezza limite superiore 270V AC limite inferiore 80V AC Un fusibile 4A 1
5. A19 eq piepuezs ZUIW L 0 UNI QUOIZOG UOT IOS SSOID OV MVI IUOISUIWIT I V UOISUIWIP IIM ROTUOII O BHUN 9 ELONEg E EI EZZOySunT yun 91U0I99 9 pue A191160 U aaia0 YSUST 07 OI OI TI 9 9 8 T v X ST ST ATI B ATILO o uoweuorzuny yuoweuorzuny W ezzoysun w ezzoySun xe xe vU QUOIZOS uonesodo uoneiodo A PZ ATI W uur wu SU SEIN ySusy x ey uornoas sso19 Z BU SUOISUIWITP IIM TAVI Osa 6 by ste 097 601 96 oz sre zsz 9 our su I zs SIE SST CH OLI KZ II Lt SIE TST Ib OLI EI Ru EE ste ost sez OLI TTI 601 wz SIE Live YET OLI OCI 801 EN SIE KTZ Go OLI 611 9 01 vl sre et os OLI STI 01 u sie oc vc OLI Lu rol T8 ste ze Sq OLI SII TOT T9 sie vez ez OLI vil TOT Ly sie zez ozz our CU ool gr SIE SC SI OLI ULI 66 ve SIE LTT SIT OLI OI L6 91 ste ce er OLI 601 96 o Ave Y A A ATIE A A DI Ee A ODEVE APT oos APT PUOISUS xey oooEnE AC los ATI 6 9I03SISOM oTENOA A A EST A A DI Xew APT UL INIAPT JINO jND APT UI ATT Ur jNd ATT Mo M9 ATT 6 JOWTSIY B119 8q 9U01Z9 0 1d euorzdo ruorzezso du ZzH09 0s O_O N Aobz 001 ER SZumas U01N99 01d 91160 pguogdo 9 by 11 Variatore di velocit BD35 e BD50 I compressori Danfoss BD35 e BD50 possono lavorare a diverse velocit di funziona
6. SSOID Z by TAB motsa SUOISUIUIIP IIM d nQ00F t by STE ER eo 9 6 OTT SIE Ur BR OLI STI EII T8 SIE SSC EHT OLI SC TI Ly STE TST Ire oz cu OI EE SIE Oe SET OLI TTI 601 ve SIE LTC WC OLI OI 8 01 8I STE STZ KEZ oz 611 BE vl SIE THC OET OLI 811 SO LI SIE es 87 OLI LTI vol CR STE LET st oun su TOI T9 SIE YET ETE OLI SI TOT Ur SIE TET OTT OLI CT 0 0I gr STE GC giz oz ru 66 YT SIE Lt SIT OLI OI L 6 91 SIE LCC 17 OLI 601 96 0 AbT V H A A ATI N A A DI PUOISUI xe ODOLHE AHT 099815 APT PUOISUD XEN oee AZ 0991S ATT 6 9103SISOH In A A Feo A A VA xeu APT umop mo mo APT xew AZI wno AZI mo mo AZI 6 1081590 B119 8q 9U0IZ9 0 1d euorzdo motzeisodut Suns U01399301d Cause pguongdo Centralina a 12 24 Vcc e 100 240 Vca L unit elettronica un dispositivo multitensione Pu essere utilizzato sia con sistemi di alimentazione da 12V 24V DC che da 100 240V AC 50 60Hz In caso di sistema di alimentazione a 12V DC la tensione massima 17V DC per sistemi di alimentazione a 24V DC la tensione massima 31 5V DC In caso di sistema di alimentazione AC la tensione massima 265V AC la tensione minima 85V AC La temperatura ambiente massima di 55 C L unit elettronica dotata di un isolamento termico incorporato che attiva ed arresta il funzionamento del compressore in caso la temperature dell unit
7. co eccessivo o se la temperatura ambiente troppo elevata l unit di controllo si surriscalder Velocit del motore troppo bassa Se il sistema di refrigerazione viene sottoposto a carico eccessivo il motore non in grado di mantenere la velocit minima di 1 850 giri min di refrigerazione troppo alta gt 5bar Arresto del ventilatore per sovracorrente Il ventilatore assorbe dall unit elettronica d con trollo una corrente superiore a 1A Arresto per protezione batteria La tensione di alimentazione si trova al di fuori del valore di stacco impostato KS Errore nell avviamento del motore Il motore bloccato o la presione differenziale nel sistema r OOSE OTIVID MONIA 000 owansiovia T 00ST OSSOY dI s 0007 Aide ou sog yu 0 o1J uoo Dsg oUnI 21010 Hi Iu EHOO OA 8 910 SISO xy Vu quouni wda C3 oo yuo poods 100 8 I0 SISOY Du 2J0SS9IdU109 YIA p ds 10ss91du09 TYT CC Lil VOI A A A A 09984 AEZ ons AHZ ODE AZI 09983S ATI A A A A gno umo APT momo APT Wna ATT Nd ATI e Du B119 eq duo1z9301d paepue s 1uorze3sodury IT Zumas uon99301d 9160 paepuezs VUOI BHUN 9 G Ua pd VJ BI eZzoYysuNT yun 91U01 99 9 pue AI yeq uaau ad 1909 0c OI OI TI 9 9 8 T T D ST ST ATI D ATL BO OJUSWIEUOIZUN UOWIEUOIZUNJ w ezzoySun w ezzoySun xe xe zU QUOIZIS uonesodo uoneiodo AEZ ATI Ww BI w ISU XEN p 3u SEIN u01 99S
8. to screw on the yellow part 2 3 Temperature adjustment and probe positioning The condensing unit has a thermostat to adjust to the required temperature The thermostat probe needs to be positioned in the return channel from the evaporator to the compressor i e the warmest part It needs to be positioned level with the return honeycomb using the clip provided 2 4 Ventilation Ventilation is essential to the refrigeration equipment for maximum performance In particular we recommend ventilating the part where the condenser is located so as to aid air circulation 19 3 WIRING CONNECTIONS 3 1 Vca Compressor The Vca compressor doesn t have a control unit and can be powered only by the Vca current though the cable with plug 3 2 Compressor with control unit Introduction The compressor provided must always be powered via the electronic control unit that is supplied with the unit Never connect the compressor pins directly to the poles of a battery or any other AC or DC power source Never connect other types of control unit Always respect the battery polarity with the control unit terminals the compressor is protected against brief accidental polarity inversions however such inversions can cause the control unit and or compressor to break The different control unit models can be powered as follows e 12 24V DC e 12 24 V DC and 100 240 V AC e 12 42 VDC We also recommend positioning a fuse between the positive batter
9. 1 deve essere montato nel cavo di tensione L per proteggere l impianto Qualora si utilizzi un interruttore principale 12 deve essere regolato ad una corrente di almeno 6A Il cavo deve avere dimensione minima di 0 75 mm2 o 18 AWG NB se necessario possibile utilizzare la connessione di terra Generale possibile collegare contemporaneamente all unit elettronica sia alimentazione AC che alimentazione DC In questo caso AC sar la fonte di alimentazione preferenziale In caso di disconnessione dell alimentazione AC o di caduta al di sotto di 85V AC si attiver il sistema di alimentazione a 12V DC con un ritardo di 1 minuto Qualora venga ristabilita l alimentazione AC non vi sar alcun ritardo nel funzionamento del compressore Protezione batteria fig 6 L arresto ed il riavvio del compressore dipendono dall impostazione dei prescelti limiti di tensione misurati sui morsetti e dell unit elettronica di controllo Le impostazioni standard per i sistemi con alimentazione rispettivamente a 12V e 24V sono indicati in fig 8 Possono comunque essere impostati altri limiti nel caso in cui si effettui una connessione per mezzo di una resistenza 9 tra i morsetti C e P Termostato fig 6 Il termostato 7 va collegato tra i morsetti C e T Senza resistenza nel circuito di controllo il compressore con unit elettronica 101N0210 o 101N0220 ruoter alla velocit di 2 000 giri min quando il termostato inserito E possibile ott
10. 42 Vcc utilizzare fusibili con le seguenti caratteristiche Alimentazione Fusibile V A 12 Vcc 30A 24 Vcc 15A 42 Vcc 10A Centralina a 12 24 Vcc L unit elettronica di controllo un apparecchiatura con possibilit di due diverse tensioni di alimentazione Ci significa che la stessa unit utilizzabile sia in sistemi con alimentazione a 12V sia a 24V La tensione massima per sistemi a 12V di 17V mentre quella per i sistemi a 24V di 31 5V La massima temperatura ambiente consentita di 55 C L unit elettronica di controllo dotata di una protezione termica incorporata che entra in funzione in caso di surriscaldamento arrestando il compressore Installazione fig 1 Collegare il connettore terminale dell unit elettronica di controllo al terminale del 6 compressore Montare l unit sul compressore incastrando il coperchio sulla testa della vite 1 Alimentazione fig 1 L unit elettronica di controllo deve essere sempre collegata direttamente ai poli della batteria 2 Connettere il polo positivo al ed il negativo al diversamente l unit non potr funzionare L unit protetta contro l inversione di polarit Per proteggere l installazione deve essere sempre montato un fusibile 3 sul cavo il pi vicino possibile alla batteria Si raccomanda l uso di un fusibile da 15A per il circuito a 12V e di un fusibile da 7 5A per il circuito a 24V Se si fa uso di interrutto
11. S SSOID OV MVI IUOISUIWIT I V UOISUIWIP IIM ROTUOII O BHUN 9 ELONEg E EI EZZOySunT yun 91U0I99 9 pue A191160 U aaia0 YSUST 07 OI OI TI 9 9 8 T v X ST ST ATI B ATILO o uoweuorzuny yuoweuorzuny W ezzoysun w ezzoySun xe xe vU QUOIZOS uonesodo uoneiodo A PZ ATI W uur wu SU SEIN ySusy x ey uornoas sso19 Z BU SUOISUIWITP IIM TAVI Osa 6 by ste 097 601 96 oz sre zsz 9 our su I zs SIE SST CH OLI KZ II Lt SIE TST Ib OLI EI Ru EE ste ost sez OLI TTI 601 wz SIE Live YET OLI OCI 801 EN SIE KTZ Go OLI 611 9 01 vl sre et os OLI STI 01 u sie oc vc OLI Lu rol T8 ste ze Sq OLI SII TOT T9 sie vez ez OLI vil TOT Ly sie zez ozz our CU ool gr SIE SC SI OLI ULI 66 ve SIE LTT SIT OLI OI L6 91 ste ce er OLI 601 96 o Ave Y A A ATIE A A DI Ee A ODEVE APT oos APT PUOISUS xey oooEnE AC los ATI 6 9I03SISOM oTENOA A A EST A A DI Xew APT UL INIAPT JINO jND APT UI ATT Ur jNd ATT Mo M9 ATT 6 JOWTSIY B119 8q 9U01Z9 0 1d euorzdo ruorzezso du ZzH09 0s O_O N Aobz 001 ER SZumas U01N99 01d 91160 pguogdo 9 by 25 The speed exchanger on the BD35 and BD50 Danfoss compressors BD35 and BD50 can work at different velocity because of the speed exchanger applied to the electronic unit of the gr
12. cise amounts optimised to achieve the best possible cooling performance The first connection between them already means an instant passing of gas between the two components thereby unbalancing the amounts of gas Always keep the connection between the same units Do not connect two units AA iready used previously with other units This will cause insufficient cooling performance or even the breakdown of the refrigeration equipment For more information on the possible unit combinations see the table 17 Vol MAX It AIR COMPRESSOR TYPE compartment to refrigerate 4 2000 2500 3000 2000 2500 3000 3500 1500 2100 f 2800 3500 rpm rpm rpm rpm rpm rpm rpm rpm rpm rpm rpm sarete ed eee e ER e NEESS eee pe E E BEEN e S LL RE RTE DS EE WT De KE Sd SEO Patel e e p e e p IRE co S E ca S SS fet I E e EVAPORATORS HOLDING PLATE VENTILATED 18 2 2 Snap on joint connections The snap on joints need to be connected with extreme care and attention because if made incorrectly this could cause irreversible damage to the unit The snap on joints in both the motor condenser part and in the evaporator section are complete with coloured end pieces red and yellow as shown in the figure Make the connection as follows e remove the coloured caps and connect the two units as in the figure ei sal yellow gt red aa ee red gt yellow e hold the red part still with a 16 mm wrench e usea 19 mm wrench
13. di secondo Alla sequenza di lampeggiamento segue un intervallo privo di emissioni luminose e quindi la sequenza relativa ad ogni errore rilevato ripetuta ogni 4 secondi Numero Tipo di errore lampeggi Arresto termico dell unit elettronica Se il sistema di refrigerazione stato sottoposto a cari co eccessivo o se la temperatura ambiente troppo elevata l unit di controllo si surriscalder Velocit del motore troppo bassa Se il sistema di refrigerazione viene sottoposto a carico eccessivo il motore non in grado di mantenere la velocit minima di 1 850 giri min Errore nell avviamento del motore Il motore bloccato o la presione differenziale nel sistema di refrigerazione troppo alta gt 5bar Arresto del ventilatore per sovracorrente Il ventilatore assorbe dall unit elettronica d con trollo una corrente superiore a 1A Arresto per protezione batteria La tensione di alimentazione si trova al di fuori del valore di stacco impostato 10 Z DOC OTIVIO MOTBA 000 OYIN MOVIA 00S7 OSSOY AIY e 0007 ZE VU 0 ouoo Duo om 9J0 OUI oO IUA BHOO PA 8 G10JSISOH VU Ian wdi U og guo paads 1070 8 JOISTSOY OL By DAOSSIACUIOD BHIO PA p ds z0ssoidui0od sz Cu rol A A A osoeye AEZ oo0vjs Apz oscene AZI 099 S AZI A A A mo mama Apz ino no Apz umo AZI mo AZI EINE q 9U0IZI 01d paepuezs ruorze sodury 3un39s 001 99 01d
14. enere altre velocit del compressore comprese nella gamma 2000 3500 giri min inserendo una resistenza 8 per la regolazione della corrente mA nel circuito di controllo I valori della resistenza per diverse velocit del motore sono riportati in fig 10 Ventilatore opzionale fig 6 E possibile collegare un ventilatore 5 tra i terminali ed F Collegare il positivo al e il negativo ad F Poich la tensione di uscita tra i morsetti ed F viene sempre regolata a 12V va utilizzato un ventilatore a 12V sia nel caso di alimentazione a 12V che nel caso di alimentazione a 24V L uscita per il ventilatore in grado di fornire una corrente continua di 0 5 Aavg In fase di accensione comunque permesso un assorbimento di corrente maggiore per un tempo di 2 secondi Lampada opzionale fig 6 Una lampada da 5 Watt 12V DC 10 pu essere collegata fra i morsetti A e C La tensione 9 d uscita fra i morsetti A e C sempre regolata su 12V DC Sia con il sistema di alimentazione a 12V che con quello a 24V deve essere utilizzata una lampada 12V DC L uscita della lampada pu erogare una tensione continua di 0 5A di media LED opzionale fig 6 Un LED da 10mA 6 pu essere collegato fra i morsetti e D In caso l unit elettronica rilevi un errore di funzionamento il diodo lampeggia per un determinato numero di volte Questo numero dipende dal tipo di errore di funzionamento rilevato Ogni lampeggiamento ha la durata di 4
15. enzione in quanto l errata esecuzione di tale procedimento pu provocare danni irreversibili all unit I giunti rapidi sia nella parte motore condensatore che nella parte dell evaporatore sono provvisti di terminali colorati rosso e giallo come in figura Per il collegamento effettuare i seguenti passi e toglierei tappi colorati e collegare le due unit come in figura i i giallo gt rosso aa de 10550 gt giallo e mantenere ferma con una chiave inglese misura 16 la parte rossa e avvitare con una chiave inglese 19 la parte gialla 2 3 Regolazione della temperatura e posizionamento della sonda L unit condensatrice provvista di un termostato per la regolazione della temperatura desiderata La sonda del termostato v posizionata nel canale di ritorno dell evaporatore al compressore ovvero la parte pi calda Essa dovr essere posizionata in corrispondenza del nido d ape di ritorno attraverso la clip in dotazione sl OL 2 4 Aerazione L aerazione dell apparato frigorifero di fondamentale importanza per la massima resa dello stesso In particolare si raccomanda di aerare la parte ove posizionato il condensatore predisponendo un condotto d ingresso e uno d uscita in modo tale da favorire la circolazione dell aria 3 COLLEGAMENTI ELETTRICI 3 1 Compressore in corrente alternata Il compressore predisposto per la corrente alternata non provvisto di centralina ed alimentabile solo a corrente a
16. erating if the voltage is too low The battery protection level needs to be set as follows 27 Cut ont Dei Rated voltage range Di In the table the AV value is the difference between cut out and cut in i e the cut in value is equal to the sum of the cut out and AV The speed exchanger on the GD30 compressor To change the velocity of the compressor put the speed exchanger into the SPI socket that you can find on the electronic unit 4 BASE UNIT ND35H20 ND50H20 WITH LIQUID COOLER 4 1 Installation The cooling unit is equipped with a condenser sea water refreshed In the middle of condenser is fixed a table thermostat that allow pump OPTIONAL working when condenser is overheated In this way we have possibility to let pump working only when necessary Thermostat tablet for pump E control eg Entry water flow Exit water flow 4 2 Tecnical data Alim base unit 12 24V Alim Pump 24V Compressor BD35f BD50f Pump self priming tipe Dim base unit mm 240x175x150 Dim pump mm 160x200x95 Pump flow 12 5 l min 3 3 GPM 28 4 3 wired diagram 29 30 DICHIARAZIONE DI CONFORMITA La VITRIFRIGOsrl con sede in via della Produzione 9 61022 Montecchio PU Italia DICHIARA sotto la propria responsabilit che il frigorifero o unit refrigerante per la refrigerazione ed il mantenimento di cibi e bevande i cui dati sono riportati nell etichetta sottostan
17. for 12 V and 24 V power supply systems appear in fig 8 Other settings are optional if a connection which includes a resistor 9 is established between terminals C and P Thermostat fig 6 The thermostat 7 is connected between the terminals C and T Without any resistor in the control circuit the compressor will run with a fixed speed of 2 000 rpm when the thermostat is switched on Other fixed compressor speeds in the range between 2 000 and 3 500 rpm can be obtained when a resistor 8 is installed to adjust the current mA of the control circuit Resistor values for various motor speeds appear in fig 10 Fan optional fig 6 A fan 5 can be connected between the terminals and F Connect the plus to and the minus to F Since the output voltage between the terminals and F is always regulated to 12 V a 12 V fan must be used for both 12 V and 24 V power supply systems The fan output can supply a continuous current of 0 5 Aavg A higher current draw is allowed for 2 seconds during start Lamp optional fig 6 A 12 V DC 5 Watt lamp 10 can be connected between the terminals A and C The output voltage between the terminals A and C is always regulated to 12 V DC A 12 V DC lamp can be used with both the 12 V and 24 V power supply The lamp output is a continuous output current of 0 5 A on average LED optional fig 6 A 10mA light emitting diode LED 6 can be connected between the terminals and D If the electronic uni
18. he cable as close to the battery as possible It is recommended to use 15 A fuses for 12 V and 7 5 A fuses for 24 V circuits If a main switch 4 is used it should be rated to a current of min 20 A The wire dimensions in fig 7 must be observed Avoid extra junctions in the power supply system to prevent voltage drops from affecting the battery protection setting AC The wires must be connected to the terminals marked L and N on the electronic unit Rated voltages from 100 to 240 V AC 50 60 Hz Safety breaker Upper safety cut out limit 270 V AC and lower limit 80 V AC A 4A fuse 11 must be fitted on the live L cable to protect the installation If a main switch 12 is used it should be rated to a current of min 6A The wire dimensions must be min 0 75 mm2 or AWG 18 NB An earth connection can be used if required General Both the AC and the DC power supply can be connected to the electronic unit at the same time In this case AC will be the preferred power supply source If the AC power supply is disconnected or drops below 85 V AC on a 12 V DC supply system a time delay of 1 min will be activated before the compressor continues on DC power supply If the AC power supply is re established there will be no delay in compressor operation Battery protection fig 6 The compressor is stopped and re started again according to pre established voltage limits measured on the and terminals of the electronic unit The standard settings
19. ichiesta di resa frigorifera E possibile ottenere altre velocit del compressore comprese nella gamma 2000 3500 giri min inserendo una resistenza 8 per la regolazione della corrente mA nel circuito di controllo I valori della resistenza per diverse velocit del motore sono riportati in fig 5 Ventilatore opzionale fig 1 E possibile collegare un ventilatore 5 tra i terminali ed F Collegare il positivo al e il negativo ad F Poich la tensione di uscita tra i morsetti ed F viene sempre regolata a 12V va utilizzato un ventilatore a 12V sia nel caso di alimentazione a 12V che nel caso di alimentazione a 24V L uscita per il ventilatore in grado di fornire una corrente continua di 0 5 Aavg In fase di accensione comunque permesso un assorbimento di corrente maggiore per un tempo di 2 secondi LED opzionale fig 1 E anche possibile collegare un diodo LED da 10 mA 6 tra i morsetti e D Nel caso in cui l unit elettronica di controllo registri un errore di funzionamento il diodo lampegger un certo numero di volte Il numero dei lampeggi dipende dal tipo di errore registrato con una durata per ciascun lampeggio di 1 4 di secondo Alla sequenza di lampeggi fa seguito una pausa senza lampeggiare dopo di che la sequenza relativa all errore in questione verr ripetuta ogni 4 secondi Numero Tipo di errore lampeggi Arresto termico dell unit elettronica Se il sistema di refrigerazione stato sottoposto a cari
20. lternata attraverso il cavo con spina 3 2 Compressore dotato di centralina Introduzione Il compressore in dotazione deve essere sempre alimentato attraverso la centralina elettronica che fornita assieme all unit Non connettere mai direttamente i pin del compressore ai poli di una batteria o di qualsiasi altra fonte di energia in corrente continua o alternata Non connettere altri tipi di centraline elettroniche Rispettare sempre la polarit della batteria con i terminali della centralina elettronica il compressore protetto da accidentali inversioni di polarit di breve durata tuttavia l inversione della polarit pu comportare la rottura della centralina e o del compressore I diversi modelli di centralina possono essere alimentati H 12 24 Vcc H 12 24 Vcc e 100 240 Vac e 12 42 Vcc Si raccomanda oltresi di posizionare un fusibile tra il polo positivo della batteria o dell alimentatore ed il terminale positivo dell alimentazione della centralina elettronica Per veicoli con chassis connessi al terminale positivo della batteria posizionare un fusibile tra il polo negativo della batteria o dell alimentatore ed il terminale negativo dell alimentazione della centralina elettronica Per i modelli di compressore BD 35 e BD50 12 24 Vcc 12 24Vcc e 100 240 Vac utilizzare fusibili del seguente amperaggio Alimentazione Fusibile V A 12 Vcc 15A 24 Vcc 7 5 A Per il modello di compressore GD30 FDC 12
21. mento grazie al variatore di velocit applicato sulla centralina elettronica del gruppo Per poter variare la velocit del compressore basta collegare un capo del termostato al morsetto contrassegnato con la lettera C e l altro capo al morsetto T corrispondente alla velocit che si intende ottenere vedi Figura1 La Figural riporta tutti i collegamenti elettrici La velocit riportata nel variatore viene espressa in giri al minuto RPM Realizzando il ponte tra i due terminali C ed I presenti nel riquadro etichettato LOW LEVEL si imposta una soglia di batteria inferiore ai valori standard i valori di soglia sono riportati nella Tabellai sottostante Per la selezione della corretta velocit fare riferimento alle indicazioni riportate nella Tabella2 Variatore di velocit N giri compressore rom 2160 ROSSO 2830 MARRONE Installazione del variatore di velocit Soglia di batteria Standard 10 4 V 11 7 V 22 8 V 24 2 V 12 Centralina a 12 42 Vcc La centralina pu essere alimentata con qualsiasi tensione da 12 a 42 Vcc Ogni unit fornita con un driver elettronico dedicato FDC1 che dispone di tutte le protezioni sia per la batteria che il driver stesso ivi compreso il compressore La tensione della rete elettrica si regola automaticamente Il compressore GD30 FDC deve essere sempre alimentato dalla centralina elettronica dedicata FDC1 Installazione L unit di controllo FDC1 ha una
22. morsettiera dove vengono fatti tutti i collegamenti Il layout dei cablaggi sono mostrati in figura CID ruse IA Maal Ki A ELECTRONIC DRIVER marte bri Te sar 4 0 de nari D I i 0000 Hi P y em i sec l x te LH Err INTEGRAL maen 106 lil sa U H gt al 0000 em A4 AN aen mmer geren pati Alimentazione Rispettare sempre la polarit della batteria con i terminali di input della centralina L unit protetta contro i danni causati da inversioni di polarit dell alimentazione il compressore se collegato erroneamente non funziona correttamente Si ricorda inoltre di inserire un fusibile tra il polo positivo dell alimentazione DC o la batteria e il polo positivo della centralina elettronica Si racomanda un fusibile da 30A per 12Vcc 15A per 24Vcc e 10A per 42Vcc In sistemi alimentati da una sorgente di corrente continua variabile il fusibile deve essere scelto seguendo le regole sopra citate considerando la tensione massima erogabile dall alimentatore DC Per evitare eccessivi cali di tensione sui cavi la loro lunghezza e sezione trasversale deve essere correlata alla tensione di alimentazione come indicato in tabella Cross section Rated Operating Range 12 14V emy aweay Se viene inserito qualsiasi tipo di interruttore o connettore tra i poli della batteria e i terminali della centralina la resistenza non deve suprare i 10mQ altrimenti i cavi indicati nella tabella sop
23. nd 3 500 rpm can be obtained when a resistor 8 is installed to adjust the current mA of the control circuit Resistor values for various motor speeds appear in fig 5 Fan optional fig 1 A fan 5 can be connected between the terminals and F Connect the plus to and the minus to F Since the output voltage between the terminals and F is always regulated to 12 V a 12 V fan must be used for both 12 V and 24 V power supply systems The fan output can supply a continuous current of 0 5 Aavg A higher current draw is allowed for 2 seconds during start LED optional fig 1 A 10mA light emitting diode LED 6 can be connected between the terminals and D If the electronic unit records an operational error the diode will flash a number of times The number of flashes depends on what kind of operational error was recorded Each flash will last Ya second After the actual number of flashes there will be a delay with no flashes so that the sequence for each error recording is repeated every 4 seconds Error type Electronic unit thermal stop If the cooling system has been overloaded or the ambient temperature is too high the control unit will overheat Insufficient motor speed If the cooling system is overloaded the motor is IG no longer able to maintain a minimum speed of 1 850 rpm Motor start error The motor is blocked or the differential pressure of the cooling system is too high gt 5bar Fan stop due to overcurren
24. ontrollo presente solo nei modelli a corrente continua al fine di evitare precoci rotture del compressore dovute a cicli termostatici troppo frequenti programmata per generare un ritardo di 3 minuti tra ogni stop e la successiva ripartenza del compressore stesso 2 INSTALLAZIONE 2 1 Introduzione I due componenti principali delle unit refrigeranti unit condensatrice ed unit evaporatrice sono precedentemente caricate con gas R134A di quantit ben precise e ottimizzate per ottenere la migliore resa del frigorifero Il primo collegamento tra loro comporta gi all istante un passaggio di gas tra i due componenti sbilanciando cos le quantit di gas Mantenere sempre il collegamento tra le stesse unit Non collegare due unit Ae usate in precedenza con altre unit Questo causer una resa insufficiente dell apparato refrigerante se non la rottura dello stesso Per maggiori informazioni sui possibili abbinamenti delle unit consultare la tabella Vol MAX It TIPOLOGIA COMPRESSORE vano da refrigerare i rae a a rpm rpm rpm rpm rpm rpm rpm rpm rpm rpm rpm SR Ae ee a rd RE I O Pa CI N O ee TT ee TT Pre pe I I rae foo Pe TT AGE A e I moe NC e E pepe O PT CO O ES Pepe O NC O ES m O N O I ES Ell EVAPORATORI SCATOLATI AD ACCUMULO AIR10 200 VENTILATO E 2 gt Q ala 2 2 Collegamento dei giunti rapidi T Il collegamento dei giunti rapidi v fatto con estrema cura ed att
25. oup In order to change the velocity of the compressor it is enough to connect one of the cables of the thermostat to the terminal marked with the letter C and other cable to the terminal T that corresponds to the velocity that you desire Picture1 The picturei reproduces all the electrical connections The velocity on the speed exchanger is indicated by revolutions per minute RPM Realising the connection between the two terminals C and I present in the picture labelled with LOW LEVEL you put the voltage of battery that it is inferior to the standard The values of the threshold are reproduced in the Table below For the selection of the right velocity please refer to the indication on the Table2 Speed Exchanger Speed compressor rpm Speed exchanger color 1500 No variation exchanger 2160 RED 2830 BROWN 3500 BLUE Installation of the Speed Exchanger Battery threshold Standard 10 4 V 11 7 V 22 8 V 24 2 V 26 12 42 V DC Control unit The control unit can be powered with any voltage from 12 to 42 V DC Each unit is provided with a dedicated electronic driver FDC1 which has all of the protections for both the battery and the driver itself including the compressor The mains voltage is adjusted automatically The GD30 FDC compressor must always be powered from the dedicated electronic control unit FDC1 Installation The FDC1 control unit has a terminal strip to which all connections a
26. protection of the installation a fuse 3 must be fitted to the cable as close to the battery as possible It is recommended to use 15 A fuses for 12 V and 7 5 A fuses for 24 V circuits If a main switch 4 is used it should be rated to a current of min 20 A The wire dimensions in fig 2 must be observed Avoid extra junctions in the power supply system to prevent voltage drops from affecting the battery protection setting Battery protection fig 1 The compressor is stopped and re started again according to pre established voltage limits measured on the and terminals of the electronic unit The standard settings for 12 V and 24 V power supply systems appear in fig 3 Other settings fig 4 are optional if a connection which includes a resistor 9 is established between terminals C and P In solar applications without a battery a 220 kW resistor is recommended In AEO Adaptive Energy Optimizing speed mode the BD compressor will always adapt its speed to the actual cooling demand within a random operation voltage of 9 6 to 31 5 V Thermostat fig 1 The thermostat 7 is connected between the terminals C and T Without any resistor in the control circuit the compressor will run with a fixed speed of 2 000 rpm when the thermostat is switched on With the thermostat directly connected to terminal C the electronic unit 101N0300 will adjust its speed to the actual cooling demand Other fixed compressor speeds in the range between 2 000 a
27. racitata devono essere dimezzati o la sezione raddoppiata Protezione batteria La centralina dotata di un sistema di protezione della batteria che impedisce al compressore di funzionare nel qual caso che la tensione risultasse troppo bassa Il livello di protezione della batteria dovrebbe essere impostato come segue 13 Cut ont ei Rated voltage range Di Nella tabella il valore AV la differenza tra cut out e cut in ovvero il valore cut in pari alla somma tra cut out e AV Variazione di giri del compressore Per variare la velocit del compressore inserire il variatore di valocit nella presa SPI presente sulla cdentralina 4 GRUPPO ND35H2O ND50H20 RAFFREDDATO AD ACQUA 4 1 Installazione Il gruppo provvisto di un condensatore raffreddato con acqua di mare AI centro del condensatore viene fissato un termostato a pasticca che invia il consenso alla pompa OPZIONALE di lavorare nel momento del surriscaldamento del condensatore In questo modo si avr la possibilit di tenere in funzione la pompa solo quando necessario Termostato a pasticca per P P i Ingresso flusso acqua controllo pompa sn Uscita flusso acqua 4 2 Dati tecnici Alim gruppo 12 24 V Alim pompa 24V Compressore BD35f BD50f Pompa tipo autoadescante Dim gruppo mm 240x175x150 Dim pompa mm 160x200x95 Portata pompa 12 5 l min 3 3 GPM 14 4 3 Collegamento eletrico
28. re generale 4 esso va dimensionato per un minimo di 20A Le dimensioni dei cavi raccomandate in fig 2 devono essere rispettate Evitare ulteriori connessioni al sistema di alimentazione per evitare che eventuali cadute di tensione influiscano sulle impostazioni per la protezione della batteria Protezione batteria fig 1 L arresto ed il riavvio del compressore dipendono dall impostazione dei prescelti limiti di tensione misurati sui morsetti e dell unit elettronica di controllo Le impostazioni standard per i sistemi con alimentazione rispettivamente a 12V e 24V sono indicati in fig 3 Possono comunque essere impostati altri limiti fig 4 nel caso in cui si effettui una connessione per mezzo di una resistenza 9 tra i morsetti C e P Nelle applicazioni per pannelli solari senza batteria si raccomanda un resistore da 220 kW Nella modalit AEO ottimizzazione energetica mediante controllo adattativo il compressore BD adatter sempre la propria velocit alla reale richiesta di resa frigorifera entro una tensione d esercizio casuale compresa tra 9 6 e 31 5 V Termostato fig 1 Il termostato 7 va collegato tra i morsetti C e T Senza resistenza nel circuito di controllo il compressore con unit elettronica 101N0210 o 101N0220 ruoter alla velocit di 2 000 giri min quando il termostato inserito Con il termostato collegato direttamente al terminale C l unit elettronica 101N0300 adatter la propria velocit alla reale r
29. re made The wiring layout is shown in the figure C ruet Pr IA Foct A A ELECTRONIC DRIVER SES b E eg I a marte i sr bri tt gem BAT op AAN F ii COCO g lt d L Te D i CLOCTROGIC INTRGRAL MAMAGER ee BO T it gem Lem di L 6 C AN aen couren pasti Power supply Always respect the battery polarity with the control unit input terminals The unit is protected against damaged caused by power supply polarity inversion the compressor will not operate properly if incorrectly connected Also remember to insert a fuse between the positive pole of the DC supply or the battery and the positive pole of the electronic control unit We recommend a 30 A fuse for 12 V DC 15 A for 24 V DC and 10 A for 42 V DC In systems powered from a variable DC source the fuse needs to be chosen according to the above rules considering the maximum voltage that can be supplied from the DC feeder To prevent excessive voltage drops along the wiring the length and cross section needs to be related to the power voltage as listed in the table Cres ston z 15 If any type of breaker or connector is inserted between the poles of the battery and the control unit terminals the resistance must not exceed 10m otherwise the wiring in the table listed above will have to be halved in length or the cross section doubled Battery protection The control unit has a battery protection system to prevent the compressor from op
30. t The fan is drawing more than 1 A from the electronic control unit Battery protection stop The power voltage is outside the set disconnect value 21 r OOSE OTIVID MONIA 000 owansiovia T 00ST OSSOY dI s 0007 Aide ou sog yu 0 o1J uoo Dsg oUnI 21010 Hi Iu EHOO OA 8 910 SISO xy Vu quouni wda C3 oo yuo poods 100 8 I0 SISOY Du 2J0SS9IdU109 YIA p ds 10ss91du09 TYT CC Lil VOI A A A A 09984 AEZ ons AHZ ODE AZI 09983S ATI A A A A gno umo APT momo APT Wna ATT Nd ATI e Du B119 eq duo1z9301d paepue s 1uorze3sodury Zumas uon99301d 9160 paepuezs VUOI BHUN 9 G Ua pd VJ BI eZzoYysuNT yun 91U01 99 9 pue AI yeq uaau ad 1909 0c OI OI TI 9 9 8 T T D ST ST ATI D ATL BO OJUSWIEUOIZUN UOWIEUOIZUNJ w ezzoySun w ezzoySun xe xe zU QUOIZIS uonesodo uoneiodo AEZ ATI Ww BI w ISU XEN p 3u SEIN u01 99S SSOID EN Z by TAB motsa SUOISUIUIIP IIM d nQ00F t by STE ER eo 9 6 OTT SIE Ur BR OLI STI EII T8 SIE SSC EHT OLI SC TI Ly STE TST Ire oz cu OI EE SIE Oe SET OLI TTI 601 ve SIE LTC WC OLI OI 8 01 8I STE STZ KEZ oz 611 BE vl SIE THC OET OLI 811 SO LI SIE es 87 OLI LTI vol CR STE LET st oun su TOI T9 SIE YET ETE OLI SI TOT Ur SIE TET OTT OLI CT 0 0I gr STE GC giz oz ru 66 YT SIE Lt SIT OLI OI L 6 91 SIE LCC
31. t records an operational error the diode will flash a number of times The 23 number of flashes depends on what kind of operational error was recorded Each flash will last 1 4 second After the actual number of flashes there will be a delay with no flashes so that the sequence for each error recording is repeated every 4 seconds EA TOS Electronic unit thermal stop If the cooling system has been overloaded or the ambient temperature is too high the control unit will overheat Insufficient motor speed If the cooling system is overloaded the motor is no longer able to maintain a minimum speed of 1 850 rpm Motor start error The motor is blocked or the differential pressure of the cooling system is too high gt 5bar EJ Fan stop due to overcurrent The fan is drawing more than 1 A from the electronic control unit SS Battery protection stop The power voltage is outside the set disconnect value 24 EN z DOC OTIVIO MOTBA 000 OYIN MOVIA 00S7 OSSOY AIY e 0007 ZE VU 0 ouoo Duo om 9J0 OUI oO IUA BHOO PA 8 G10JSISOH VU Ian wdi U og guo paads 1070 8 JOISTSOY OL By DAOSSIACUIOD BHIO PA p ds z0ssoidui0od Ir sz CU YOI A A A A osoeye AEZ osstIs Apz oscene AZI 099 S AZI A A A A mo mama Apz momo Apz umo AZI mo AZI SUaUgO 9U0IZI 01d paepuezs ruorze sodury 3un39s 001 99 01d A19 eq piepuezs ZUIW L 0 UNI QUOIZOG UOT IO
32. te e dalla quale questa dichiarazione si riferisce E CONFORME ai requisiti essenziali di sicurezza previsti dalle direttive 2006 95 EEC 2004 108 EEC DECLARATION OF CONFORMITY VITRIFRIGOsrl with it mainoffice in via della Produzione 9 61022 Montecchio PU Italy Here by DECLARES under its sole responsibility that the refrigerator or refrigerating unit designed for the refrigeration and preserva tion of food and beverages asper the data plate indicated below and towhich this declaration refers COMPLIES WITH THE basic safety requirements specified in EC directives 2006 95 EEC 2004 108 EEC Vitri Alceste Ros ay SE 31 n CH gt oO L fon Ke CH H N n VITRIFRIGO s r l Via Della Produzione 9 61020 Montecchio PU Tel 39 0721 491080 Fax 39 0721 497739 www vitrifrigo com E mail vitrifrigo vitrifrigo com
33. y pole or feeder and the positive supply terminal of the electronic control unit For vehicles with chassis connected to the positive terminal of the battery position a fuse between the negative pole of the battery or feeder and the negative supply terminal of the electronic control unit For BD35 and BD50 compressor models use fuses with the following amperage Power V Fuse A 12 V DC 15A 24 V DC 7 5A For the GD30 FDC compressor use fuses with the following characteristics Power V Fuse A 12 VDC 30A 24 V DC 15A 42 V DC 10 A 12 24 V DC Control unit The electronic control unit is a dual voltage device This means that the same unit can be used in both 12V and 24V power supply systems The maximum voltage for 12 V systems is 17 V while for 24 V systems it is 31 5 V Maximum permitted ambient temperature is 55 C The electronic control unit is equipped with an incorporated thermal breaker to stop the compressor in case of overheating Installation fig 1 Connect the terminal plug from the electronic unit to the compressor terminal Fit the electronic unit on the compressor by snapping the cover over the screw head 1 20 Power supply fig 1 The electronic unit must always be connected directly to the battery poles 2 Connect the plus to and the minus to otherwise the electronic unit will not work The electronic unit is protected against reverse battery connection For

Download Pdf Manuals

image

Related Search

Related Contents

Samsung ST5500 Manual de Usuario  EHV+ APPLICATION MANUAL  INFORMATIQUE AVANCEE  PowerLite Pro Cinema G6900WU Kit Brochure    Manual  Yoyo Data Loggers  Bedienungsanleitung User manual MAXI-SENSOR FR - geo    DIRIS A40/A41 2 Outputs kWh - kvarh - KVAh  

Copyright © All rights reserved.
Failed to retrieve file