Home
manuale istruzioni
Contents
1. Operation with the 0 10V input The minimum voltage input to turn on the device is Vin 1 2V Increasing or decreasing the input voltage in range 1 2V 10V increase or decrease the brightness of all the LEDs connected to the outputs Voltage inputs lower than 1 2V threshold turn off the device NB The remote control or keys cannot be used in association with 0 10V input It is not possible to drive outputs independently 2009 Entity Elettronica s r l Tutti i diritti riservati Versione Documento 1 1 0 Versione Software EN0723 1 1 Descrizione morsetti Terminal block description Simbolo Symbol Funzione Function Note Note A Ingresso tensione i 12 24V_ Vn connesso internamente a VSS alimentazione Vm is internally connected to VSS VIN power voltage input i y Ingresso 0 10V Il dispositivo riconosce automaticamente il tipo di segnale 10V 0 10V input collegato p Device automatically identify the connected signals Comune ingresso segnali Comune per pulsanti ingresso 0 10V e ingresso VSS sionals common input sincronizzazione 9 p Common bus for buttons 0 10V input and synchronisation input Connettere a T3 della scheda successiva TXA Trasmettitore per gt sincronizzazione dispositivi CoRReetto TAON NENEK MENGE TXB i Connettere a VSS della scheda successiva y Connect to VSS of the next device ON OFF dispositivo in modalit uscite sincronizzate colore
2. Funzione del dispositivo Il dispositivo dotato di tre uscite utilizzabili per comandare The device has three outputs that can drive one or more standard LES Entity e in modalit uscite sincronizzate aumentare o e in synchronized output mode increase or decrease the brightness of all the LEDs simultaneously uno o pi LED colore singolo o RGB e consente di diminuire la luminosit di tutti i LED contemporaneamente e in modalit uscite indipendenti aumentare o diminuire la luminosit dei LED connessi a ciascuna uscita elettronica s r l Manuale di istruzioni User Manual EN 0723 e in modalit colore selezionare un colore ed aumentarne o diminuirne la luminosit E disponibile nelle versioni con uscita in tensione ENO723 VD oppure in corrente ENO0723 CD Device function or RGB LEDs and allows e in independent output mode increase or decrease the brightness of the LEDs connected to a given output separatamente in color mode select a color and increase decrease its brightness Two versions are available one with voltage output ENO723 VD one with current output EN0723 CD Codici d ordine Order code 1200 EN 0723 VD ViDi 24 Dimmer con uscita in tensione Voltage output dimmer 1200 EN 0723 VD TC ViDi 24 TC Dimmer con uscita in tensione con radiocomando Voltage output dimmer with remote control 1200 EN 0723 CD 035 CIDi 035 Dimmer con uscita
3. pulsanti 2 e 3 T2 T3 per fissare il colore selezionato ed attivare la modalit colore Effettuata l impostazione della modalit premere e rilasciare brevemente il T1 per accendere o spegnere i LED La pressione prolungata di T1 consente di aumentare o diminuire la luminosit del colore preselezionato anche in questa modalit il raggiungimento dei limiti di variazione viene segnalato con un breve spegnimento ed il rilascio del pulsante inverte la direzione di variazione della luminosit Nota volendo accendere i LED all alimentazione del dispositivo possibile programmarlo nella modalit desiderata quindi dopo aver scollegato l alimentazione collegare T2 a VSS Operation with keys not included Synchronized output mode To select this mode push key 1 and key 2 T1 T2 at the same time Once this mode has been selected push and release T1 to turn ON OFF the device When the device is on keep T1 pressed to increase or decrease the brightness of all the LEDs connected to the device The dimmer informs you when it reaches the minimum maximum brightness by turning off the LEDs for a moment If the key is not released after another moment the direction of brightness variation is reversed At brightnesses other than the extremes every release and press of T1 inverts the direction of brightness variation The keys T2 and T3 have no effect in this mode Independent output mode To select this mode push key 1 and key 3 T1 T3 at the sa
4. ON OFF uscita 1 in modalit uscite indipendenti T1 Pulsante 1 aumento diminuzione luminosit dei LEDs Key 1 Device power in synchronised outputs color mode ON OFF output 1 in independent outputs mode increase decrease LED brigthness ON OFF uscita 2 in modalit uscite indipendente T2 Pulsante 2 aumento diminuzione luminosit dei LEDs Key 2 ON OFF output 2 in independent outputs mode increase decrease LED brigthness Pulsante 3 Ingresso seriale di ON OFF uscita 3 in modalit uscite indipendente T3 sincronizzazione aumento diminuzione luminosit dei LEDs Key 3 Series synchronising ON OFF output 3 in independent outputs mode input increase decrease LED brigthness CH1 RA Anodo LED LED Anode A MEI CH1 RK Catodo LED LED Cathode 1 n CH2 GA Anodo LED LED Anode K CH2 GK Catodo LED LED Cathode RN TE utilizzando il dimmer con LED RGB collegare al canale 1 colore CH3 BA Anodo LED LED Anode rosso al canale 2 colore verde al canale 3 colore blu With RGB lamps connect channel 1 to red color channel 2 to CH3 BK Catodo LED LED Cathode green color channer 3 to blue color Esempi di collegamento Connection examples EN SPOT H2 3 Vin amp Entity C e 10V CIDI 350 R cm vss TXA Constant Current 3 c E Channels PWM i e T1 Dimmer B CH3 pa e amp Entity CE ViDi 24 Voltage 3 Channels PWM Dimmer R CH1 G CH2 B CH3 E
5. drain EN0723 Current output per channel SUE CD Chx Chx ENO723 CD 315 350 385 mA Note In EN0723 VD Chx outputs are internally connected and match the positive input after the protection fuse Chx outputs are Taone diusia EN0723 VD 0 Vn 1 independent open drain In EN0723 CD all outputs are Ran Vout independent EN0723 CD 0 Vn 1 9 Note 1 EN0723 VD requires an external current driver On EN0723 l 7 a e CD LEDs can be directly connected A requenza di uscita A 4 Fout 190 200 210 Hz Note 2 EN0723 VD Chx Chx gt gt gt open drain output N A E EN0723 CD Chx Chx w i if dea di temperatura 20 9 50 C emperature range Funzionamento tramite pulsanti non inclusi Modalit con uscite sincronizzate Questa modalit viene selezionata attraverso la pressione contemporanea dei pulsanti 1 e 2 T1 T2 Effettuata la selezione della modalit premere e rilasciare T1 per l accensione o lo spegnimento del dispositivo A dispositivo acceso la pressione prolungata di T1 consente di aumentare o diminuire la luminosit di tutti i LED collegati al dispositivo Il raggiungimento del massimo o del minimo della luminosit viene segnalato dal dispositivo con lo spegnimento dei LED per un breve istante se la pressione del pulsante non viene interrotta dopo una breve attesa la direzione di variazione della luminosit verr invertita A luminosit intermedie ogni rilascio e nuova
6. in corrente Constant current output dimmer 1200 EN 0723 CD 035 TC Dimmer con uscita in corrente CIDi 035 TC con radiocomando Constant current output dimmer with Dimmer PWM Caratteristiche Features ra e Ingresso 0 10V e 0 10V input 9 e 3 ingressi NPN per controllo tramite pulsanti esterni e 3 NPN inputs for keyboard control se E PWM Dimmer e Ingresso uscita di sincronizzazione con altri dispositivi nput output to synchronize to other EN0723 devices Dimensioni dimensions EN0723 e Inverse polarity protection 165 x 40 x 25 mm e Protezione contro le inversioni di polarit e Output overload protection e Protezione contro il sovraccarico delle uscite Serle CiDi vetre l vee Nota nel modello EN0723 VD le uscite Chx sono connesse ViD Caratteristiche tecniche Simbolo Modello UdM internamente e corrispondono al positivo di ingresso dopo il fusibile serle IDI Technical features Symbol Version Min Typ Max UoM di protezione le uscite Chx sono indipendenti tra loro open drain Nel modello EN0723 CD tutte le uscite sono indipendenti tra loro Tensione di alimentazione V 10 8 _ 26 4 V Nota 1 per EN0723 VD richiesto un regolatore di corrente esterno Voltage power iN i i de per EN0723 CD i LED possono essere connessi direttamente all uscita senza ulteriori limitatori Altre correnti disponibili a richiesta CEE E E END 2 5 A Nota 2 EN0723 VD Chx Chx gt gt gt Uscita open
7. in figura Il segnale di sincronizzazione viene rigenerato da ogni dispositivo quindi non vi sono limiti sul numero di dispositivi collegabili On y the first device master has a control input Other devices slaves synchronize to the first Every device regenerates the synchronizing signal so there is no limit to the number of devices that can be connected Max 6 lampade per canale 24Vdc Max 6 lamps for each channel 24Vdc Max 7 pz per canale 24Vdc Max 7 pcs for each channel 24Vdc EN SPOT H2 RGB Full Color Max 6 lampade 24Vdc Max 6 lamps for each chain 24Vdc Ero VARRONE O D E Riassunto delle modalit di funzionamento con selezione da pulsanti Riassunto delle modalit di funzionamento con radiocomando Summary of function modes operating with keys Summary of function modes operating with remote radio control Uscite sincronizzate Uscite indipendenti Colore Uscite indipendenti Colore T1 T2 Selezione T1 T3 STE T2 T3 Selezione Regolazione luminosit brightness controll ON OFF Regolazione pe gt usa al ua o i pal TR1 pm Canale Channel1 luminosit contemporanea EI contemporanea SERI contemporanea E TR4 brightness at the same time push at the same time push at the same time push TR2 pren e Canale Channel 2 control Regolazione luminosit brightness control ION OFF TR3 e Canale Channel 3 ON OFF Pia TA e Canale Cha
8. N SPOT H2 RGB Full Color Rosso verDE amp Entity CE CiDi 350 Constant Current 3 Channels PWM Dimmer R CH1 G CH2 B CH3 ORORO ROR NERO JO en FOSSO GRIGIO VERDE VARRONE a_i Controllo tramite pulsanti keyboard control Pulsante 1 Key 1 accensione e spegnimento dimmer variazione luminosit sincronizzata o canale 1 turn on or off the dimmer changes the brightness of all channels or of channel 1 Pulsante 2 Key 2 accensione e spegnimento canale 2 variazione luminosit canale 2 turn on or off channel 2 changes the brightness of channel 2 Pulsante 3 Key 3 accensione e spegnimento canale 3 variazione luminosit canale 3 turn on or off channel 3 changes the brightness of channel 3 vedere paragrafo Funzionamento tramite pulsanti per maggiori informazioni see chpt Operation with keys for more information Controllo tramite ingresso 0 10V 0 10V input control Da 0 a 1 2V Range 0 1 2V uscite spente outputs power off Da 1 2V a 10V Range 1 2V 10V aumento diminuzione della luminosit dei LED increases decreases LED brightness Collegamento in serie per sincronizzazione Synchronizing series connection 12 24V COM MASTER SLAVE Il controllo viene effettuato solo sul primo dispositivo master dispositivi slave si sincronizzano al master attraverso i collegamenti indicati
9. el minimo della luminosit viene segnalato dal dispositivo con lo spegnimento dei LED per un breve istante se la pressione del pulsante non viene interrotta dopo una breve attesa la direzione di variazione della luminosit verr invertita Il rilascio del pulsante a luminosit intermedie inverte la direzione di variazione della luminosit La singola pressione accende o spegne l uscita associata Operation with remote radio control Setting of the remote control code The remote control is generally provided with a standard factory code For this reason we suggest to set a personalized code for the remote control device If you need to change this code move dip switches situated above the battery from 1 to 7 8 is not used You have to make the acquisition of the remote code in order to make the dimmer recognize the radio control see following paragraph Remote control recognition Before using the remote radio control you need to save the remote control code into the dimmer as described below connect the dimmer outputs power on the dimmer and let all outputs off connect inputs T 2 T 3 and VSS on the dimmer for a while if you have connected a keyboard press both key 2 and 3 e the dimmer activates the outputs in a fast sequence you must disconnect T 2 T 3 and VSS or release keys 2 and 3 e press any key on the radio control within 10 seconds to complete recognition Operation with radio control The rem
10. ghtness variation Note if you like to light the LEDs when supplying power set the device in the desired mode then shut off the power and connect T2 to VSS Controllo tramite radiocomando Impostazione del codice radiocomando Il radiocomando viene generalmente fornito con un codice standard E consigliato impostare un codice personalizzato cambiando la configurazione dei dip switch da 1 a 7 8 non utilizzato Successivamente eseguire la procedura di riconoscimento del nuovo codice Riconoscimento del radiocomando AI primo utilizzo e ad ogni variazione necessario memorizzare il codice del radiocomando nel Dimmer secondo la procedura di seguito descritta e alimentare il dispositivo lasciando spente le uscite e collegare gli ingressi T2 e T3 a VSS nel caso siano collegati i pulsanti premere contemporaneamente i pulsanti 2 e 3 le uscite vengono attivate in sequenza veloce scollegare T2 e T3 da VSS o rilasciare i pulsanti 1 e 2 e entro 10 secondi premere un tasto qualsiasi del radiocomando per completarne il riconoscimento Funzionamento del radiocomando tasti 1 2 e 3 TR1 TR2 e TR3 del radiocomando controllano separatamente le uscite mentre il tasto 4 TR4 controlla le 3 uscite contemporaneamente code setting dip switch La pressione prolungata di ognuno dei tasti TR1 TR2 TR3 consente di aumentare o diminuire la luminosit dei LED collegati alla relativa uscita Il raggiungimento del massimo o d
11. ibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The CE marking of components does not guarantee the compliance of the end product and does not absolve the manufacturer of the end product from fulfilment of legal obligations Entity Elettronica s r l publishes this manual without making any warranty as to the content herein Entity reserves the right to make modifications additions and deletions to this manual due to typographical errors inaccurate information or improvements to programs and or equipment at any time and without notice Entity Elettronica s r l via dei Laghi 19 36077 Altavilla Vicentina VI tel 39 0444 574488 fax 39 0444 370482 www entityel it info entityel it
12. me time all the keys will drive each output independently Once this mode has been selected push and release T1 to turn ON OFF the LEDs connected to output 1 In the same way use T2 or T3 to drive the LEDs connected to output 2 or 3 respectively When the LEDs connected to an output are ON keep the respective key pressed to increase or decrease their brightness The dimmer informs you when it reaches the minimum maximum brightness by turning off the LEDs for a moment If the key is not released after another moment the direction of brightness variation is reversed At brightnesses other than the extremes every release and press of a key inverts the direction of brightness variation Color mode With the device connected to RGB LEDs it is possible to use it to get the desired light color and increase or decrease its intensity In independent output mode change the three output brightnesses to get the desired color Then push key 2 and 3 T2 T3 at the same time to fix the color and enable the color mode Once this mode has been selected push and release T1 to turn ON OFF all the LEDs Keep T1 pressed to increase or decrease the color brightness the dimmer informs you when it reaches the minimum maximum brightness by turning off the LEDs for a moment If the key is not released after another moment the direction of brightness variation is reversed At brightnesses other than the extremes every release and press of T1 inverts the direction of bri
13. nnel1 Ka T1 brightness x T1 gt brightness control T2 canale c hannel 2 controll SOA T3 mm Canale Channel3 SNo 2009 Entity Elettronica s r l Tutti i diritti riservati Versione Documento 1 1 0 Versione Software EN0723_D 1 1 Avvertenze Il costruttore declina ogni responsabilit nel caso di inosservanza delle precauzioni di installazione da parte di personale non qualificato o installazione non corretta Il prodotto non deve essere smaltito assieme agli altri rifiuti Gli utenti devono provvedere allo smaltimento delle apparecchiature da rottamare portandole al luogo di raccolta indicato per il riciclaggio delle apparecchiature elettriche ed elettroniche La marcatura di singoli componenti non garantisce che il prodotto finito sia a norma e non solleva quindi l utilizzatore dall adempimento degli obblighi di legge relativi al prodotto finito Entity Elettronica S r l declina ogni responsabilit per eventuali inesattezze contenute nel presente manuale e si riserva inoltre la facolt di modificare senza preavviso le caratteristiche del prodotto dati e le caratteristiche riportate nel presente manuale contemplano una tolleranza del 10 Warning Entity Elettronica declines all responsabilities from the in observance of installation precautions by non qualified personell or incorrect installation The product must not be disposed of with your other waste Instead it is your respons
14. ote control keys 1 2 and 3 TR1 TR2 and TR3 drive each output independently whereas key 4 TR4 drives all outputs simultaneously Single pression of keys TR1 TR2 TR3 turn on or off the respective output Keeping pressed each key when the output is on increases or decreases their brightness The dimmer informs you when it reaches the minimum maximum brightness by turning off the LEDs for a moment If the key is not released after another moment the direction of brightness variation is reversed At brightnesses other than the extremes every release and press of a key inverts the direction of brightness variation battery Figura 1 Picture 1 Il tasto TR4 agisce con le stesse modalit su tutte le uscite contemporaneamente mantenendone la proporzione di luminosit TR4 operates in the same way but on all outputs always in the same proportion P dip switch Apertura del radiocomando Opening of the remote control battery Funzionamento con ingresso 0 10V La tensione di ingresso minima per l accensione del dispositivo Vin 1 2V Aumentando o diminuendo la tensione di ingresso nel range 1 2V 10V il dispositivo aumenta o diminuisce la luminosit di tutti i LED collegati alle uscite Tensioni d ingresso inferiori al valore di soglia Vin 1 2V causano lo spegnimento del dispositivo NB Nelle installazioni con ingresso 0 10V non possibile l utilizzo del radiocomando n dei pulsanti n la gestione separata dei canali
15. pressione del pulsante T1 inverte la direzione di variazione della luminosit In questa modalit i pulsanti T2 e T3 non hanno alcun effetto Modalit con uscite indipendenti Questa modalit viene selezionata attraverso la pressione contemporanea dei pulsanti 1 e 3 T1 T3 i pulsanti 1 2 e 3 controlleranno separatamente ciascuna uscita Effettuata la selezione della modalit premere e rilasciare T1 per accendere spegnere i LED collegati all uscita 1 utilizzare nello stesso modo T2 o T3 per controllare i LED collegati all uscita 2 o 3 rispettivamente La pressione prolungata di un pulsante consente di aumentare o diminuire la luminosit dei LED collegati alla relativa uscita Il raggiungimento del massimo o del minimo della luminosit viene segnalato dal dispositivo con lo spegnimento dei LED per un breve istante se la pressione del pulsante non viene interrotta dopo una breve attesa la direzione di variazione della luminosit verr invertita Il rilascio del pulsante a luminosit intermedie inverte la direzione di variazione della luminosit Modalit colore Collegando al dispositivo dei LED RGB possibile ottenere il colore desiderato ed aumentarne o diminuirne l intensit luminosa Con il dispositivo impostato in modalit ad uscite indipendenti vedere paragrafo precedente variare l intensit luminosa delle tre uscite fino ad ottenere il colore desiderato premendo i pulsanti 1 2 e 3 Premere quindi contemporaneamente i
Download Pdf Manuals
Related Search
Related Contents
Samsung SM-G310HN Uživatelská přiručka お施主様へ必ず本説明書をお渡しください。 Graco Pack 'n Play 9261 User's Manual PS_FR_Mediadisk_LNX HD_wifi_Series.ai FM transmitter CZH-05A User Manual Manual do usuário Copyright © All rights reserved.
Failed to retrieve file