FlexPointTM 10T/2
Contents
1. RJ45 Cross Over switch When connecting the UTP to a hub or switch it should be set to Straight Through factory setting When connecting to a PC or workstation it should be set to Cross Over Termination switch When attaching anywhere along a coax cable except at the end the Termination switch should be set to Termination Out factory setting When attaching at the end of a cable it can be set to Termination In When the switch is set to Termination In an external termination must not be attached NORMAS OFICIALES MEXICANAS NOM ELECTRICALSAFETY STATEMENT 1 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado 2 Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura 3 Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas 4 Todas las instrucciones de operaci n y uso deben ser seguidas 5 El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc 6 El aparato el ctrico debe ser usado nicamente con carritos o pedelstales que sean recomendados por el fabricante 7 El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante 8 Servicio El usuario no debe intentar dar servicio al equipo2. aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparto ha sido tirado o su cubierta ha sido da ada LED indicators LED Color Description Power Yellow Power applied Jabber Red Jabber condition Coax Rx Green Received data on coax line Coax Col Yellow Collision on coax line UTP Rx Green Received data on UTP line UTP Col Yellow Collision on UTP line UTP Link Green Operational device detected at the far end of UTP Polarity Yellow Polarity reversal was detected and corrected automatically Copyright 2001 Black Box Corporation All rights reserved 1000 Park Drive e Lawrence PA 15055 1018 724 746 5500 e Fax 724 746 0746
3. el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado 9 El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra or superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n 10 El equipo el ctrico deber ser situado fuera del alcance de uentes de calor como radiadores registros de calor estufas u ostros aparatos incluyendo amplificadores que producen calor 11 El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato LED indicators LED Color Description Power Yellow Power applied Jabber Red Jabber condition Coax Rx Green Received data on coax line Coax Col Yellow Collision on coax line UTP Rx Green Received data on UTP line UTP Col Yellow Collision on UTP line UTP Link Green Operational device detected at the far end of UTP Polarity Yellow Polarity reversal was detected and corrected automatically Copyright 2001 Black Box Corporation All rights reserved 1000 Park Drive e Lawrence PA 15055 1018 724 746 5500 e Fax 724 746 0746 12 Precaci n debe ser tomada de tal manera que la tierra fisica y la
4. it should be set to Straight Through factory setting When connecting to a PC or workstation it should be set to Cross Over Termination switch When attaching anywhere along a coax cable except at the end the Termination switch should be set to Termination Out factory setting When attaching at the end of a cable it can be set to Termination In When the switch is set to Termination In an external termination must not be attached 12 Precaci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada 13 Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato 14 El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante 15 En caso de existir una antena externa deber ser localizada lejos de las lineas de energia 16 El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo 17 Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n 18 Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del
5. 6 ft E Dimensions Weight W 3 0 xD 4 0 xH 1 0 2 lb E Power 9 VDC 600 mA E Environmental Temperature 0 to 40 degrees C Humidity 0 90 non condensing YA O SN Black Box Corporation X The World s Source for Cabling and Network Connectivil OU l JULY 2001 LMC210A LMC210AE FlexPoint 10T 2 CUSTOMER Order toll free in the U S Call 877 877 BBOX SUPPORT utside U S call 724 746 5500 INFORMATION FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail infoO blackbox com TRADEMARKS All applied for and registered trademarks are the property of their respective owners FEDERAL COMMUNICATIONS COMMISSION AND CANADIAN DEPARTMENT OF COMMUNICATIONS RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates uses and can radiate radio frequency energy and if not installed and used properly thatis in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is li
6. anera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra or superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n 10 El equipo el ctrico deber ser situado fuera del alcance de uentes de calor como radiadores registros de calor estufas u ostros aparatos incluyendo amplificadores que producen calor 11 El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato Mounting The FlexPoint 10T 2 can be individually wall mounted using a wall mounting kit rack mounted using a 5 position space saver shelf or inserted in a 14 position power redundant FlexPoint Powered Chassis When wall mounting or shelf mounting attach the power adapter unit If connecting the UTP cable to a hub or switch set the cross over switch to the straight position factory set ting If connecting to a PC or workstation set the switch to the cross over position When connecting the FlexPoint 10T 2 at the end of a coax segment attach the coax cable directly into the FlexPoint s BNC coax connector When connecting it along the coax cable not at the end use a T connector to tap into the cable Switch Settings RJ45 Cross Over switch When connecting the UTP to a hub or switch
7. be used only with a Listed Direct Plug In Power Unit marked Class 2 and rated at 9Vdc 1 Amp 2 This product should always be used only with its enclosed Power Unit WARNING Before plugging the Power Adapter to any wall outlet or AC power source verify that the power on the unit is appropriate for your AC line voltage source NORMAS OFICIALES MEXICANAS NOM ELECTRICALSAFETY STATEMENT 1 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado 2 Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura 3 Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas 4 Todas las instrucciones de operaci n y uso deben ser seguidas 5 El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc 6 El aparato el ctrico debe ser usado nicamente con carritos o pedelstales que sean recomendados por el fabricante 7 El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante 8 Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado 9 El aparato el ctrico debe ser situado de tal m
8. kely to be cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num irques de las classe A prescrites dans le R glement sur le brouillage radio lectrique publi par le minist re des Communications du Canada Overview and Description The FlexPoint M family of Converters supports the IEEE 802 3 and Ethernet Versions 1 0 2 0 standards They convert among 10Base FL with single mode SM and multi mode MM fiber 10Base 2 thin coax and 10Base T twisted pair UTP media types The FlexPoint 10T 2 provides conversion from 10Base 2 coax to 10Base T UTP It features coax connector and an ElA TIA 568 RJ45 UTP connector The FlexPoint 10T 2 supports switch selectable Straight through or crossed RJ45 UTP wiring and a switch selectable coax line termination Installation and Configuration Power Adapter Notice 1 When used in a stand alone configuration this product is intended to
9. ma O LA Black Box Corporation A The World s Source for Cabling and Network Connectivity oO OOOO JULY 2001 LMC210A LMC210AE FlexPoint 10T 2 CUSTOMER Order toll free in the U S Call 877 877 BBOX SUPPORT utside U S call 724 746 5500 INFORMATION FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail infoC blackbox com Specification E Protocol IEEE 802 3 10Base T 10Base 2 E Interface Connectors UTP 1 RJ45 pins 1 2 3 6 active Coax 1 BNC EH Cable Types 10Base T UTP Categories 3 4 5 EIA TIA 568 10Base 2 Coax 50 ohm RG 58A U RG 58C U RG 58 U or equivalent EH Supported Distances 10Base T UTP 100 m 328 ft 10Base 2 Coax 185 m 606 ft E Dimensions Weight W 3 0 xD 4 0 xH 1 0 2 lb E Power 9 VDC 600 mA E Environmental Temperature 0 to 40 degrees C Humidity 0 90 non condensing Overview and Description The FlexPoint family of Converters supports the IEEE 802 3 and Ethernet Versions 1 0 2 0 standards They convert among 10Base FL with single mode SM and multi mode MM fiber 10Base 2 thin coax and 10Base T twisted pair UTP media types The FlexPoint 10T 2 provides conversion from 10Base 2 coax to 10Base T UTP It features coax connector and an EIA TIA 568 RJ45 UTP connector The FlexPoint 10T 2 suppo
10. n expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num irques de las classe A prescrites dans le R glement sur le brouillage radio lectrique publi par le minist re des Communications du Canada Mounting The FlexPoint 10T 2 can be individually wall mounted using a wall mounting kit rack mounted using a 5 position space saver shelf or inserted in a 14 position power redundant FlexPoint Powered Chassis When wall mounting or shelf mounting attach the power adapter unit If connecting the UTP cable to a hub or switch set the cross over switch to the straight position factory set ting If connecting to a PC or workstation set the switch to the cross over position When connecting the FlexPoint 10T 2 at the end of a coax segment attach the coax cable directly into the FlexPoint s BNC coax connector When connecting it along the coax cable not at the end use a T connector to tap into the cable Switch Settings
11. polarizaci n del equipo no sea eliminada 13 Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato 14 El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante 15 En caso de existir una antena externa deber ser localizada lejos de las lineas de energia 16 El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo 17 Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n 18 Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparto ha sido tirado o su cubierta ha sido da ada Specification E Protocol IEEE 802 3 10Base T 10Base 2 E Interface Connectors UTP 1 RJ45 pins 1 2 3 6 active Coax 1 BNC EH Cable Types 10Base T UTP Categories 3 4 5 EIA TIA 568 10Base 2 Coax 50 ohm RG 58A U RG 58C U RG 58 U or equivalent E Supported Distances 10Base T UTP 100 m 328 ft 10Base 2 Coax 185 m 60
12. rts switch selectable Straight through or crossed RJ45 UTP wiring and a switch selectable coax line termination Installation and Configuration Power Adapter Notice 1 When used in a stand alone configuration this product is intended to be used only with a Listed Direct Plug In Power Unit marked Class 2 and rated at 9Vdc 1 Amp 2 This product should always be used only with its enclosed Power Unit WARNING Before plugging the Power Adapter to any wall outlet or AC power source verify that the power on the unit is appropriate for your AC line voltage source TRADEMARKS All applied for and registered trademarks are the property of their respective owners FEDERAL COMMUNICATIONS COMMISSION AND CANADIAN DEPARTMENT OF COMMUNICATIONS RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to be cause interference in which case the user at his ow
Download Pdf Manuals
Related Search