kv7012a BASE
Contents
1. 17 4 3 2 Switching USB Devices Only 18 4 3 3 Switching to Another Computer But Allowing USB Devices to Remain on the Current Port 18 4 3 4 Switching Computers and USB Devices 18 A 9 5 ANULOSCATI nda Der Roe De eee eu 19 4 5 6 Flash Upgrade sessi eere hb hog cellent dvd gent 19 Appendix Troubleshooting 20 A Calling Black BOX us PER eR ppb ER Peg Settee dies 20 A 2 Shipping and Packaging sinus site s aeta eG G6236 3 204 69455 20 2 AND 4 PORT SERVSWITCH DT PRO KVM SWITCH 1 Specifications Resolution 2048 x 1536 85 Hz Bandwidth 400 MHz Supported Operating Systems Windows 98 Me 2000 XP and Windows NT Hotkeys Yes User Controls KV7012A 1 port selection button KV7013A 4 port selection buttons Connectors KV7012A Computer end Keyboard 2 6 pin mini DIN female Mouse 2 6 pin mini DIN female Monitor 2 HD15 female USB computer 2 USB 2 0 Type B Flash 1 8 pin mini DIN Console end Keyboard 1 6 pin mini DIN female Mouse 1 6 pin mini DIN female Monitor 1 HD15 female USB peripherals 2 USB 2 0 Type A KV7013A Computer end Keyboard 4 6 pin mini DIN female Mouse 4 6 pin mini DIN female Monitor 4 HD15 female USB computers 4 USB 2 0 Type B Flash 1 8 pin mini DIN Console end Keyboard 1 6 pin mini DIN female Mouse2. BLACK BOX Copyright 2007 Black Box Corporation All rights reserved 1000 Park Drive Lawrence PA 15055 1018 724 746 5500 Fax 724 746 0746 a BLACK BOX NE REOR RR RR RR RR KV7012A KV7013A 2 and 4 Port ServSwitch DT Pro KVM Switch pox pudo CUSTOMER Order toll free in the U S Call 877 877 BBOX outside U S call 724 746 5500 SUPPORT FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 INFORMATION Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail info blackbox com FCC AND IC RFI STATEMENTS FEDERAL COMMUNICATIONS COMMISSION and INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS Class B Digital Device This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation However there is no guarantee that interference will not occur in a particular installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications If this equipment does cause harmful interference to radio or telephone reception which can be determined by turning the equipment off and on the user is
3. 1 6 pin mini DIN female Monitor 1 HDI5 female USB peripherals 4 USB 2 0 Type A Indicators KV7012A 2 Port LEDs KV7013A 4 Port LEDs Temperature Tolerance Operating 32 to 104 F 0 to 40 C Storage 4 to 140 F 20 to 60 C Relative Humidity Up to 80 noncondensing Power 5 VDC 2 5 A power supply specific to your country ordered separately Size KV7012A 1 8 H x 5 4 W x 5 1 D 4 6 x 13 7 x 13 cm KV7013A 1 8 H x 8 9 W x 5 3 D 4 6 x 21 1 x 13 5 cm Weight KV7012A 1 8 lb 0 8 kg KV7013A 2 2 Ib 1 kg CHAPTER 2 Overview 2 Overview 2 1 Introduction The 2 or 4 Port ServSwitch DT Pro KVM Switch allows you to control up to two or four USB and or PS 2 computers from a single PS 2 console PS 2 keyboard PS 2 mouse and monitor Supported mice include Microsoft IntelliMouse and other mice Compatible with USB Type 1 1 or 2 0 devices the ServSwitch is both compact and portable The switch also has a builtin USB Version 2 0 hub This hub allows you to connect additional shared peripherals on a one computer at a time basis Using a hotkey command sequence see Section 4 3 you can asynchronously switch the KVM control and the USB devices And the ServSwitch works with common operating systems including Windows 98 Me 2000 XP and Windows NT Flash upgradable firmware allows you to obtain the latest firmware upgrades Setup is fast and simple and there s no software to configure Its sm
4. 3 1 SELECTING USB DEVICES CONNECTED TO THE 2 AND 4 PORT USB 2 0 Hus The ServSwitch unit s built in 2 and 4 port USB 2 0 hub allows you to connect additional shared peripherals on a one computer at a time basis When you connect a USB device to the ServSwitch the device can be accessed through any computer that is connected to the installation via a simple hotkey command sequence lt Left Ctrl gt lt Left Ctrl gt H X 2 AND 4 PORT SERVSWITCH DT PRO KVM SWITCH 4 3 2 SWITCHING USB DEVICES ONLY Using the hotkey command sequence below you can share any device attached to the ServSwitch unit s built in USB 2 0 hub from your currently selected computer 1 To invoke the hotkey mode press the lt Left Ctrl gt key twice within two seconds 2 Press the H key followed by the corresponding port number 1 4 For example pressing lt Left Ctrl gt lt Left Ctrl gt H 1 switches USB hub access to the computer on port 1 4 3 3 SWITCHING TO ANOTHER COMPUTER BUT ALLOWING USB DEVICES TO REMAIN ON THE CURRENT PORT Using the hotkey command sequence below you can asynchronously switch the KVM control and the USB devices For example you can print from one computer and switch the KVM control to another computer simultaneously 1 To invoke the hotkey mode press the lt Left Ctrl gt key twice within two seconds 2 Press the C key followed by the corresponding port number 1 4 For example pressing lt Left Ctrl gt lt Left
5. Ctrl gt C 1 switches the KVM control to the computer on port 1 but the USB device access remains on the port it was NOTE Some USB storage devices are not suitable for dynamic port switching applications 4 3 4 SWITCHING COMPUTERS AND USB DEVICES Using the hotkey command sequence below you can asynchronously switch the KVM control and the USB device access to any computer 1 To invoke the hotkey mode press the lt Left Ctrl gt key twice within two seconds 2 Press the A key followed by the corresponding port number 1 4 For example pressing lt Left Ctrl gt lt Left Ctrl gt A 4 switches the KVM control and the USB hub access to the computer on port 4 CHAPTER 4 Operation 4 3 5 AUTOSCAN The AutoScan feature allows you to monitor the activity of the connected computers at regular ten second intervals so that you can monitor the computer activity without having to press the front panel buttons This time interval cannot be changed To invoke AutoScan press lt Left Ctrl gt lt Left Ctrl gt 0 NOTES The interval between these two keys should be no more than a half second Once the scanning begins it continues until you press any key to exit AutoScan A flashing port LED indicates that the connected computer is running AutoScan 4 3 6 FLASH UPGRADE With Internet flash upgrade capability you can update your ServSwitch with the latest firmware upgrades Call Tech Support for details Appendix Trou
6. el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas 4 Todas las instrucciones de operaci n y uso deben ser seguidas 5 El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc 6 El aparato el ctrico debe ser usado nicamente con carritos o pedestales que sean recomendados por el fabricante 7 El aparato el ctrico debe ser montado a la pared o al techo s lo como sea recomendado por el fabricante 8 Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado 9 El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra o superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n 10 El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u otros aparatos incluyendo amplificadores que producen calor 11 El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato NOM STATEMENT 12 Precauci n de
7. encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult an experienced radio TV technician for help CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment To meet FCC requirements shielded cables and power cords are required to connect this device to a personal computer or other Class B certified device This digital apparatus does not exceed the Class B limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de classe B prescrites dans le Reglement sur le brouillage radio lectrique publi bar Industrie Canada 2 AND 4 PORT SERVSWITCH DT PRO KVM SWITCH NORMAS OFICIALES MEXICANAS NOM ELECTRICAL SAFETY STATEMENT INSTRUCCIONES DE SEGURIDAD 1 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado 2 Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura 3 Todas las advertencias en
8. GA male connector from your monitor to the console VGA port on the back of the ServSwitch See Figure 3 2 4 Port ServSwitch DT Pro KVM Switch KV7013A E AE al Monitor Figure 3 2 Console connections 3 2 2 POWERING ON THE SERVSWITCH Connect the 5 V 2 5 A power adapter s barrel connector to the power jack on the rear of the switch Then plug the power adapter cable into an available power outlet See Figure 3 3 CHAPTER 3 Installation E E He 5 V 2 5 A power adapter Figure 3 3 Power connections 3 2 3 CONNECTING THE COMPUTERS USB Installation 1 Connect the ServSwitch DT Pro s USB cable EHN7001213UV 0006 USB connector to the PC1 USB port on the back of the ServSwitch Connect the cable s VGA connector to the ServSwitch unit s PC1 VGA connector See Figure 3 4 2 Connect the cable s male VGA and USB connectors to the corresponding connectors on the back of the computer Tee Figure 3 4 USB computer connections 3 Repeat steps 1 and 2 for all computers 4 Power on your computers Your computers operating systems should recognize the ServSwitch and will automatically install the USB driver if it was not already installed on your computers 2 AND 4 PORT SERVSWITCH DT PRO KVM SWITCH NOTE On some computers you must enable USB support on your system BIO
9. S Please refer to your computer manufacturer s manual or the motherboard manual to verify that USB support is enabled PS 2 Installation 1 Connect the ServSwitch DT Pro s PS 2 CPU cable EHN7001213UVP 0006 to the computer s PS 2 keyboard PS 2 mouse and HD15 ports 2 Connect the other end of the cable to the ServSwitch unit s HD15 connector See Figure 3 5 Ca mE Ho PS 2 computer Figure 3 5 PS 2 computer connections NOTE PS 2 computers without USB ports are not able to use the built in USB 2 0 peripheral hub 3 2 4 CONNECTING THE USB PERIPHERALS Attach up to two or four USB peripherals to the USB Type A connectors on the ServSwitch See Figure 3 6 NOTE You can attach a USB keyboard and mouse but hotkey switching will not be enabled for these connections CHAPTER 3 Installation OOO SSS EJ 3960 USB peripherals Figure 3 6 USB peripheral connections 2 AND 4 PORT SERVSWITCH DT PRO KVM SWITCH 4 Operation 4 1 Powering Up the System Once all cables have been connected and all computers have been powered on the ServSwitch emulates mouse and keyboard signals on each port allowing your computer to boot normally The ServSwitch is now ready for use 4 2 Selecting Computers Using Front Panel Buttons You can instantly select any computer by pressing the port selector buttons on the front panel The corresponding LED will lig
10. ale Figure 2 2 The ServSwitch back panel views Table 2 2 Rear panel components Component Description Console VGA port Attaches to the user monitor Computer VGA ports Connect to a computer s video cards Computer PS 2 Link to a computer s keyboard and mouse ports keyboard mouse ports Computer USB Attaches to the USB port on a computer Power connector Connects to a 5 VDC 2 5 A power supply optional Flash upgrade port Attach a flash upgrade cable to this port 8 pin mini DIN 2 AND 4 PORT SERVSWITCH DT PRO KVM SWITCH 2 3 What s Included The KV7012A or KV7013A package should contain the following items If anything is missing or damaged please contact Black Box e 1 2 or 4 Port ServSwitch DT Pro KVM Switch e 1 Flash cable e This user s manual 2 4 What You ll Need to Supply e ServSwitch DT Pro Cable EHN7001213UV 0006 0009 0015 These cables connect to PCs that have USB and VGA connectors The cables are available in 6 9 and 15 foot 1 8 2 7 and 4 5 m versions ServSwitch DT Pro Cable EHN7001213UVP 0006 0009 0015 These cables connect to computers that have a PS 2 VGA and two 6 pin mini DIN connectors The cables are available in 6 9 and 15 foot 1 8 2 7 or 4 5 m versions Power supply that s specific to your country United States PS71013 US Japan PS71013 JP Europe PS71013 EU United Kingdom PS71013 UK or Aus
11. all desktop footprint is ideal for on or under your desktop Use either front panel buttons on the ServSwitch or hotkeys on your keyboard to select ports or start AutoScan The front panel buttons include integral LEDs The LED will light with the correspond ing active port when manually switching between the computers The ServSwitch beeps to confirm that it s in hotkey mode The AutoScan function allows you to automatically scan and monitor all computers one by one that are connected to the ServSwitch Its 400 MHz video bandwidth range allows the ServSwitch to support video resolutions of up to 2048 x 1536 85 Hz 2 AND 4 PORT SERVSWITCH DT PRO KVM SWITCH 2 2 Components 2 2 1 FRONT PANEL Figure 2 1 shows the 2 and 4 Port ServSwitch front views Table 2 1 describes the components numbered in the illustration Figure 2 1 The ServSwitch front panel views Table 2 1 Front panel components Component Description 6 pin mini DIN connectors PS 2 keyboard and mouse ports O Direct access port buttons Press to select a computer Port LEDs Integral LEDs on the port buttons light when the connected computer is selected USB 2 0 input ports Connect to USB peripherals USB flash drives printers etc CHAPTER 2 Overview 2 2 2 REAR PANEL Figure 2 2 shows the 2 and 4 Port ServSwitch rear views Table 2 2 describes the components numbered in the illustration
12. be ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada 13 Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato 14 El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante 15 En caso de existir una antena externa deber ser localizada lejos de las lineas de energia 16 El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo 17 Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n 18 Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparato ha sido tirado o su cubierta ha sido da ada 2 AND 4 PORT SERVSWITCH DT PRO KVM SWITCH TRADEMARKS USED IN THIS MANUAL BLACK BOX and the Double Diamond logo are registered trademarks and ServSwitch is a trademark of BB Technologies Inc PS 2 is a registered trademark of International Business Machines Corporation Inte
13. bleshooting A 1 Calling Black Box If you determine that your 2 or 4 Port ServSwitch DT Pro KVM Switch is malfunctioning do not attempt to alter or repair the unit It contains no user serviceable parts Contact Black Box at 724 746 5500 Before you do make a record of the history of the problem We will be able to provide more efficient and accurate assistance if you have a complete description including the nature and duration of the problem when the problem occurs the components involved in the problem any particular application that when used appears to create the problem or make it worse A 2 Shipping and Packaging If you need to transport or ship your 2 or 4 Port ServSwitch DT Pro KVM Switch e Package it carefully We recommend that you use the original container e If you are shipping the 2 or 4 Port ServSwitch DT Pro KVM Switch for repair make sure you include everything that came in the original package Before you ship contact Black Box to get a Return Authorization RA number
14. ht when the port is selected 4 3 Selecting Computers Using Keyboard Hotkey Commands To directly switch the KVM control to any computer via the simple keyboard command sequence press the lt Left Ctrl gt key twice and the lt up arrow gt or lt down arrow gt keys 1 To invoke the hotkey mode press the lt Left Ctrl gt key twice within two seconds The switch will beep to indicate that it s in hotkey mode 2 Press the lt up arrow gt or lt down arrow gt keys to switch to the previous or next port respectively Table 4 1 lists the hotkey commands CHAPTER 4 Operation Table 4 1 Hotkey commands Command Description lt Left Ctrl gt lt Left Ctrl gt H x Switch to USB hub device only lt Left Ctrl gt lt Left Ctrl gt lt up arrow gt Switch to previous active PC lt Left Ctrl gt lt Left Ctrl gt lt down arrow gt Switch to next active PC lt Left Ctrl gt lt Left Ctrl gt A X Switch both the PC and USB hub device lt Left Ctrl gt lt Left Ctrl gt C x Switch the KVM control only lt Left Ctrl gt lt Left Ctrl gt 0 Begin AutoScan Any key Stop AutoScan lt Left Ctrl gt lt Left Ctrl gt S Enable disable beep sound x 1 2 3 4 H USB hub device A Combined PC and hub NOTE After switching ports there is a delay of up to 2 seconds before the video displays This is normal and is due to the video signal s refresh rate 4
15. lliMouse Microsoft Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners CONTENTS Contents Chapter Page ls Spe 6ficat ns e cepe theo dh a Sere EAEE 6 Die SS NO 7 2 1 Introduction 7 2 2 Components ies a dr di oe eee eee e 8 2 2 1 Front Panel i rk 6022202062021 ene ehh a 8 22 9 Rear Parla oe A RH E e En 9 2 5 WhatsIncluded c eR ran 10 2 4 What You ll Need to Supply 10 2 Installation 5 0 RIDERE EE WESVERRU 6 gsoE AH EN RR a vers 11 3 1 ServSwitch Placement 11 3 2 Hardware Installation 11 3 2 1 Connecting the Console 11 3 2 2 Powering On the ServSwitch 12 3 2 3 Connecting the Computers 13 3 2 4 Connecting the USB Peripherals 14 4 Opera sui sen eb Me arate Cte sce i Eug Duteil ee sante 16 4 1 Powering Up the System 16 4 2 Selecting Computers Using Front Panel Buttons 16 4 3 Selecting Computers Using Keyboard Hotkey Commands 16 4 3 1 Selecting USB Devices Connected to the 2 and 4 Port USB 2 0 Hub
16. tralia PS71013 AU 3 Installation 3 1 ServSwitch Placement The 2 or 4 Port ServSwitch DT Pro KVM Switch is small portable and designed to fit on a desktop Consider the following when deciding where to place the KVM switch How long are the cables attached to your keyboard mouse and monitor How far away are the computers from the console How long are the cables you use to connect your computers to the ServSwitch CAUTION Do not place cables near machines that create electrical noise such as fluorescent lighting air conditioning equipment etc 3 2 Hardware Installation This section provides instructions for the basic hardware setup of a single ServSwitch CAUTION Before you begin make sure that power to all the devices that you will be connecting is turned off To prevent damage caused by ground potential differences make sure that all devices are properly grounded If you don t follow these instructions your computers and or the ServSwitch could be damaged 3 2 1 CONNECTING THE CONSOLE 1 Power off all computers 2 Connect your PS 2 keyboard and PS 2 mouse directly to the PS 2 keyboard and mouse ports labeled with keyboard and mouse symbols on the front of the ServSwitch See Figure 3 1 2 AND 4 PORT SERVSWITCH DT PRO KVM SWITCH 4 Port ServSwitch DT Pro KVM Switch KV7013A OO 00 E E E E Keyboard Mouse Figure 3 1 Keyboard and mouse connections 3 Connect the HD15 V
Download Pdf Manuals
Related Search