© Copyright 2001. Black Box Corporation. All rights reserved.
Contents
1. For most applications use a straight through Ethernet cable when plugging the Providers into a PC Use a cross over cable when plugging into a hub or a switch Verify the pinout of the Ethernet device into which you are connecting the Provider to determine which type of cable is required The pinout of the Provider s Ethernet port is shown in Table 2 1 Table 2 1 Ethernet port pinout Pin Number Signal RX RX TX Not used Not used TX Not used Not used 4 ON LED Indicators also described on bottom label e DS3 Lnk LED Flashing green indicates that the DS3 is operational no Red Alarm e DS3 Alm LED Steady flashing amber indicates a Yellow Blue Alarm e Power LED Steady green indicates normal operation e 100 LED Steady green indicates a Fast Ethernet 100 Mbps connection e Act LED Flashing amber indicates activity on the Ethernet segment e Lnk LED Steady green indicates that an Ethernet link has been established2. lt BLACK BOX Copyright 2001 Black Box Corporation All rights reserved 1000 Park Drive Lawrence PA 15055 1018 724 746 5500 Fax 724 746 0746 lt gt BL ACK BOX litro vivo LRA1216A 6 LRA1216A 6 DC DS3 Provider Backhaul Unit 6 Port rovider y CUSTOMER Order toll free in the U S Call 877 877 BBOX outside U S call 724 746 5500 SUPPORT FREE technical support 24 hours a day 7 days a week Call 724 746 5500 or fax 724 746 0746 INFORMATION Mailing address Black Box Corporation 1000 Park Drive Lawrence PA 15055 1018 Web site www blackbox com E mail info blackbox com FCC INFORMATION FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the in
3. e las lineas de energia 16 El cable de corriente deber ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo 17 Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilaci n 18 Servicio por personal calificado deber ser provisto cuando A El cable de poder o el contacto ha sido da ado u B Objectos han ca do o l quido ha sido derramado dentro del aparato o C El aparato ha sido expuesto a la lluvia o D El aparato parece no operar normalmente o muestra un cambio en su desempe o o E El aparato ha sido tirado o su cubierta ha sido da ada DS3 PROVIDER BACKHAUL UNIT 6 PORT TRADEMARKS USED IN THIS MANUAL Any trademarks mentioned in this manual are acknowledged to be the property of the trademark owners CHAPTER 1 Introduction 1 Introduction These instructions provide basic installation procedures for the DS3 Provider Backhaul Unit 6 Port CAUTION Excess static electricity can damage your unit Use proper static protection handling techniques when installing and handling this equipment DS3 PROVIDER BACKHAUL UNIT 6 PORT 2 Installation 1 After unpacking the Provider Unit check to make sure you have the following DS3 Provider Backhaul Unit 6 Port LRA1216A 6 or LRA1216A 6 DC 4 rubber feet 10 rackmount screws 2 rackmount brackets e Power cord AC version LRA1216A 6 on
4. ly e This users manual If anything is missing or damaged call Black Box at 724 746 5500 2 Select the site When selecting a site for the DS3 Provider Backhaul Unit consider the following e The maximum recommended temperature is 86 F 30 C Consider the internal temperature of the rack e Make sure that you place the unit so that the cables won t become a tripping hazard or become dislodged from the unit e Do not block the power supply vents or otherwise restrict airflow when installing the unit in a rack e Consider the mechanical loading of the rack so that it remains stable and unlikely to tip over e Consider the overall loading of the branch circuit before installing any equipment in a rack environment e Make sure that a reliable grounding path is maintained in the rack system This unit is intended for a grounded connection For table top mounting attach the rubber feet to the bottom of the unit For rack mounting attach the rackmount brackets to the sides of the unit at the desired position CHAPTER 2 Installation 3 Connect power to the Provider Unit from an appropriate power source Verify that the PWR LED is lit Verify that the switches on the front of the unit are in the appropriate positions for the DS3 line Plug in the local Ethernet connection and verify the physical link by the LNK LED on the front of the unit The unit will not present Ethernet Link until the DS3 line is operational NOTE
5. mendado por el fabricante 8 Servicio El usuario no debe intentar dar servicio al equipo el ctrico m s all a lo descrito en las instrucciones de operaci n Todo otro servicio deber ser referido a personal de servicio calificado 9 El aparato el ctrico debe ser situado de tal manera que su posici n no interfiera su uso La colocaci n del aparato el ctrico sobre una cama sof alfombra o superficie similar puede bloquea la ventilaci n no se debe colocar en libreros o gabinetes que impidan el flujo de aire por los orificios de ventilaci n 10 El equipo el ctrico deber ser situado fuera del alcance de fuentes de calor como radiadores registros de calor estufas u otros aparatos incluyendo amplificadores que producen calor 11 El aparato el ctrico deber ser connectado a una fuente de poder s lo del tipo descrito en el instructivo de operaci n o como se indique en el aparato NOM STATEMENT 12 Precauci n debe ser tomada de tal manera que la tierra fisica y la polarizaci n del equipo no sea eliminada 13 Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos poniendo particular atenci n a los contactos y recept culos donde salen del aparato 14 El equipo el ctrico debe ser limpiado nicamente de acuerdo a las recomendaciones del fabricante 15 En caso de existir una antena externa deber ser localizada lejos d
6. terference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la classe A prescrites dans le Reglement sur le brouillage radio lectrique publi par Industrie Canada DS3 PROVIDER BACKHAUL UNIT 6 PORT NORMAS OFICIALES MEXICANAS NOM ELECTRICAL SAFETY STATEMENT INSTRUCCIONES DE SEGURIDAD 1 Todas las instrucciones de seguridad y operaci n deber n ser le das antes de que el aparato el ctrico sea operado 2 Las instrucciones de seguridad y operaci n deber n ser guardadas para referencia futura 3 Todas las advertencias en el aparato el ctrico y en sus instrucciones de operaci n deben ser respetadas 4 Todas las instrucciones de operaci n y uso deben ser seguidas 5 El aparato el ctrico no deber ser usado cerca del agua por ejemplo cerca de la tina de ba o lavabo s tano mojado o cerca de una alberca etc 6 El aparato el ctrico debe ser usado nicamente con carritos o pedestales que sean recomendados por el fabricante 7 El aparato el ctrico debe ser montado a la pared o al techo s lo como sea reco
Download Pdf Manuals
Related Search