Home

Manual

1. amp TRENDNET 24 Port 10 100Mbps Web Smart PoE Switch with 4 Gigabit Ports and 2 Mini GBIC Slots TPE 224WS e Gu a de instalaci n r pida 1 e Troubleshooting 3 118 ESPANOL 1 Antes de iniciar Contenidos del Paquete e TPE 224WS e Gu a de instalaci n r pida multiling e e CD ROM herramienta y guia del usuario e Cable de alimentaci n e Kit para montaje en estante Si cualquiera de los contenidos anteriores se encuentra por favor contacte a su distribuidor Requisitos de instalaci n e Navegador Web Internet Explorer 6 0 6 superior e Un PC con adaptador de red instalado correctamente e Dispositivo PD Alimentado IEEE 802 3af e Cat 5 Cat 5e o Cat 6 Cable de red RJ 45 Equipo Opcional e Rack est ndar de 19 e Mini GBIC Modules p ej TEG MGBSX TEG MGBS10 TEG MGBS40 TEG MGBS80 TEG MGBS10D35 TEG MGBS40D35 Nota El TPE 224WS s lo es compatible con dispositivos PD Alimentados que siguen el est ndar IEEE 802 3af 2 Instalaci n del Hardware Nota 1 Tras completar la instalaci n del hardware utilice la herramienta de gestion para conmutador Web Smart para configurar el TPE 224WS Abra su navegador Web despu s introduzca la direcci n IP http 192 168 0 1 y la contrase a por defecto admin Compruebe que su PC y el TPE 224WS est n configurados en el mismo segmento de red 2 Las ranuras Mini GBIC estan compartidas con los puertos Ethernet Gigabit 25 y 26 Cuando las
2. 24WS Please wait until the user logs off If the other user has already logged off and you still get the same screen then disconnect the power cord from the TPE 224WS wait for 5 seconds reconnect the power cord to the TPE 224WS allow 5 seconds for the switch to power on and then attempt to access the web configuration page again 3 forgot the administration password How do I reset my TPE 224WS Press on the reset button using a pen or paperclip for 10 seconds The default password is admin Note The default password is case sensitive 4 When connect a computer to the Switch s Gigabit Ethernet port am not getting Gigabit speeds What should do 1 Check the LEDs on the Switch When the 1000Mbps LED remains off and the 100Mbps LED remains on the computer s connection speed is 100Mbps When the 1000Mbps and 100Mbps LEDs remain off the computer s connection speed is 10Mbps 2 Make sure that you have a Gigabit Ethernet adapter installed 3 Make sure to use a Cat 5e or Cat 6 Ethernet cable Some Cat 5 cables are not rated to run in Gigabit 5 My 802 3af PoE Device does not power on when plug the device into the Switch What should do 1 Verify that the PoE device supports IEEE 802 3af Mode A protocol 2 Power cycle the PoE switch Unplug power to the Switch wait 15 seconds then plug the power back in 3 Plug the device into a different port on the PoE switch 4 Try using another RJ 45 network cable If you stil
3. ais o zona de instalaci n TRENDnet 20675 Manhattan Place Torrance CA 90501 USA Copyright 02011 All Rights Reserved TRENDnet
4. l encounter problems or have any questions regarding the TPE 224WS please refer to the User s Guide included on the provided CD ROM or contact Trendnet s Technical Support Department amp TRENDNET Product Warranty Registration Please take a moment to register your product online Go to TRENDnet s website at http www rendnet com register Certifications This equipment has been tested and found to comply with FCC and CE Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received Including interference that may cause undesired operation Waste electrical and electronic products must not be disposed of with household waste Please T p recycle where facilities exist Check with you Local Authority or Retailer for recycling advice gt NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT ADVERTENCIA En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentac n necesario para su funcionamiento El uso de un adaptador distinto al mencionado puede producir da os fisicos y o da os al equipo conectado El adaptador de alimentaci n debe operar con voltaje y frecuencia de la energia electrica domiciliaria existente en el p
5. ranuras Mini GBIC se est n usando los puertos Ethernet Gigabit 25 y 26 estaran desactivados 3 Si desea encontrar con facilidad todos los conmutadores de gesti n Web en la red asigne una direcci n IP cambie la contrase a actualice la nueva versi n del firmware y despu s instale la herramienta de gesti n para conmutador Web Smart Siga los pasos indicados en la gu a del usuario 1 Conecte el Power Cord Cable de alimentaci n en la parte trasera del TPE 224WS y despu s a la toma corriente 2 Conecte un cable de red RJ 45 del PC a un puerto Ethernet disponible en el TPE 224WS 3 Conecte un cable RJ 45 desde un puerto PoE 1 24 en el TPE 224WS al puerto LAN del dispositivo PoE p ej TV IP322P e Z 7 Ww Para mas informacion sobre la configuraci n de la herramienta Smart basada en Web y de las configuraciones avanzadas consulte por favor la Gu a del Usuario que se incluye en el CD ROM de la herramienta y del controlador o en el sitio Web de TRENDnet en www trendnet com Troubleshooting 1 After connecting the TPE 224WS to a power outlet the LEDs do not turn on 1 Check the connection of the power cord to the TPE 224WS and the power outlet 2 Check that the power outlet is receiving power 2 When access the TPE 224WS using a web browser get a screen that tells me only one user can login What should do Another computer is configuring the TPE 2

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents