Home

Owner`s Manual / Manual del Propietario

image

Contents

1. Speed Clean 2500 PSI Pressure Washer Briggs amp Stratton POWER PRODUCTS 3 Twisting the nozzle adjusts the spray pattern from a narrow pattern to a fan pattern Figure 12 Figure 12 Adjusting the Nozzle for Spray Pattern Rotate nozzle counterclockwise for fan spray pattern Rotate nozzle clockwise for narrow spray pattern 4 For most effective cleaning keep spray nozzle from 8 to 24 inches away from cleaning surface 5 If you get the spray nozzle too close especially using high pressure mode you may damage the surface being cleaned 6 DO NOT get closer than 6 inches when cleaning tires Applying Detergent with the Adjustable Nozzle IMPORTANT Use soaps designed specifically for pressure washers Household detergents could damage the pump CAUTION You must attach all hoses before you start the engine Starting the engine without all the hoses connected and without the water turned ON will damage the pump To apply detergent follow these steps Review the use of adjustable nozzles 2 Prepare the detergent solution as required by the job 3 Place the filter end of the chemical injection hose into the detergent container CAUTION Keep the chemical injection hose from coming in contact with the hot muffler www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Speed Clean 2500 PSI Pressure Washer Briggs amp
2. Figura 7 Fijar el L Perno a la Manubrio fo av fed F Gancho del Fi a Pistola fof Gancho del Manguera LA Lise 4 y 9 4 Inserte el L gancho del agujero apenas arriba la cartelera en el derecho de la manija visto desde la parte posterior de la unidad Sostenga el gancho en lugar con los alicates y asocie la tuerca de fijaci n con una llave del 7 16 Figura 17 www mymowerparts com Lavadora de Presi n 2500 PSI de Speed Clean Briggs Stratton POWER PRODUCTS Agregar Aceite al Motor IMPORTANTE Cualquier intento para arancar el motor antes de haberle proporcionado el mantenimiento apropiado con el aceite recomendado podr a ocasionar la falla del motor Coloque la lavadora a presi n sobre una superficie nivelada Consulte el manual del propietario del motor para a adir al motor el aceite recomendado NOTA Verifique el aceite del motor de manera frecuente cuando ste se esfuerce demasiado A ada Gasolina ADVERTENCIA NUNCA llene el tanque de combustible en recintos cerrados NUNCA llene el tanque de combustible cuando el motor est funcionando o est caliente NO fume cuando est llenando el tanque de combustible ADVERTENCIA NO llene excesivamente el tanque de combustible Deje suficiente espacio para la expansi n del combustible e Coloque la lavadora a presi n sobre una superficie nivelada Consulte el manual del propietario
3. Stratton POWER PRODUCTS 4 Slide the adjustable nozzle forward to low pressure CAUTION Firmly grasp spray gun with both mode Detergent cannot be applied with the nozzle in hands when using high pressure spray to avoid high pressure position injury if gun kicks back 5 Make sure the garden hose is connected to the water inlet Check that the high pressure hose is connected to the spray gun and the pump Start the engine NOTE You can also stop detergent from flowing by simply removing chemical injection hose from bottle 2 Keep the spray gun a safe distance from the area you 6 Apply the detergent to a dry surface starting at lower plan to spray portion of area to be washed and work upward using long even overlapping strokes 3 Apply a high pressure spray to a small area then check the surface for damage If no damage is found it is okay a 7 Allow the detergent to soak in for 3 5 minutes to continue cleaning before washing and rinsing Reapply as needed to prevent surface from drying DO NOT allow the detergent to dry on prevents streaking IMPORTANT You must flush the chemical injection system after each use by placing the filter into a bucket of Automatic Cool Down System clean water then run the pressure washer in low pressure Thermal Relief for l 2 minutes If you run the engine on your pressure washer for Pressure Washer Rinsing 3 5 minutes without pressing the trigger on the spray gun c
4. posici n OFF M i CUANDO ALMACENE O GUARDE EL EQUIPO CON A 3 E COMBUSTIBLE EN EL TANQUE Chispear involuntario puede tener como resultado el A ADVERTENCIA fuego o el golpe el ctrico Almacene alejado de calderas estufas calentadores de agua secadoras de ropa u otros aparatos electrodom sticos que posean pilotos u otras fuentes de ignici n porque ellos pueden encender los vapores de la gasolina CUANDO AJUSTE O HAGA REPARACIONES A SU MAQUINA LAVADORA DE PRESION Siempre desconecte el alambre de la buj a y col quelo donde no pueda entrar en contacto con la buj a A ADVERTENCIA La corriente de agua de alta presi n que produce este equipo pueden perforar la piel y sus tejidos Laa profundos ocasionando lesiones serias y posible A PRECAUCION amputaci n Hacer funcionar el motor a velocidades excesivas aumenta el NUNCA apunte la pistola a la gente animales o plantas riesgo de lesiones personales NO permita en ning n momento que NI OS operen la m quina NO juegue con partes que puedan aumentar o disminuir la velocidad lavadora a presi n de mando e NUNCA repare la manguera de alta presi n Remplacela NO opere la m quina lavadora a presi n con un valor de presi n superior a su clasificaci n de presi n A ADVERTENCIA PRECAUCION Los motores al funcionar producen calor La temperatura del silenciador y de las reas cercanas El rociado de alta presi n puede da ar elementos fr giles puede alca
5. reacondicionado y destinado a demostraciones el equipo utilizado como fuente principal de energ a en lugar del servicio de la compa a proveedora de electricidad y el equipo destinado a aplicaciones utilizadas para mantener la vida BRIGGS STRATTON POWER PRODUCTS GROUP LLC JEFFERSON WISCONSIN U S A www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 BRIGGS amp STRATTON POWER PRODUCTS OWNER WARRANTY POLICY Effective January 2003 LIMITED WARRANTY Briggs amp Stratton Power Products will repair or replace free of charge any part or parts of the equipment that are defective in material or workmanship or both Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser This warranty is effective for the time periods and subject to the conditions provided for in this policy For warranty service find the nearest Authorized service dealer by calling 800 743 4115 Warranty service may only be performed by a Briggs amp Stratton Power Products Authorized service dealer THERE IS NO OTHER EXPRESS WARRANTY IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE TIME PERIOD SPECIFIED OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUS
6. DE CONTENIDOS Reglas De Seguridad 0 0 00 ce ee ee ee eee 18 19 Conozca Su Generador 0 0 0 0 eee eee eee 20 Ensamblaje cic a vce ce eet reesi ceed a a baa ina 21 23 FuncionamientO 0 ees 24 26 Especificaciones Del Producto 0 0000 27 Mantenimiento ss i4 4fdesscp etna e we ae dae 27 29 Almacenamiento via t 29 Diagnosticos De Averias 00 0 0 cece ee eee 30 Piezas De Recambio 00 cece eens 16 17 Garat o aan ads 31 DESCRIPCI N DEL EQUIPO Lea este manual de manera cuidadosa y MN familiar cese con su generador Conozca sus usos sus limitaciones y cualquier peligro relacionado con el mismo Se ha hecho cada esfuerzo posible para asegurarse que la informaci n que aparece en este manual es exacta y se encuentra actualizada Sin embargo Briggs amp Stratton se reserva el derecho a cambiar alterar o de otra manera mejorar el producto y este documento en cualquier momento sin previo aviso INSTRUCCIONES DE SEGURIDAD ste es el s mbolo de alerta de seguridad Sirve A para advertir al usuario de un posible riesgo para su integridad f sica Siga todos los mensajes de seguridad que figuren despu s de este s mbolo para evitar lesiones o incluso la muerte El s mbolo de alerta de seguridad dh es usado con una palabra PELIGRO ADVERTENCIA PRECAUCI N un mensaje por escrito o una ilustraci n para alertarlo acerca de cualquier situaci n de peligro que
7. Entrada de Agua Conexi n para la manguera de jard n Etiqueta de Datos Proporciona el modelo revisi n y el n mero de serie de lavadora de presion Tenga por favor estos prontamente disponible cu ndo llamar para la ayuda Filtro de Aire El elemento de filtro tipo seco limita la cantidad de suciedad y polvo que se introduce en el motor Palanca de la V lvula Arrancador de Retroceso e gt de Regulaci n EAS Perilla del Cebador a Filtro de Aire Filtro y Tubo para Boquilla Ajustable Tapa del Dep sito del Aceite Filtro y Tubo para Recolecci n de Detergente Usado para succionar detergente de la botella de qu micos a la corriente de agua de baja presi n Manguera de Alta Presi n Conecte un extremo a la pistola de rociado y el otro extremo a la toma de alta presi n Palanca de Control de la V lvula de Regulaci n Coloca el motor en modo de arranque para el arrancador de retroceso y detiene el motor en funcionamiento Perilla del Cebador Usada para arranque de motores fr os Pistola de Rociado Controla la aplicaci n de agua sobre la superficie de limpieza con el gatillo Incluye cerrojo de seguridad Tapa del Combustible Llene el tanque con gasolina regular sin contenido de plomo en este punto Tapa del Dep sito del Aceite Llene el motor con aceite aqu Siempre habitaci n de hoja para la expansi n del combustible Toma de Alta Presi n Conexi n para la m
8. Figure 6 Tighten by hand Figure 6 Connect High Pressure Hose to Pump Q WARNING DO NOT overfill the fuel tank Always allow room for fuel expansion e Place pressure washer on a level surface e Refer to engine owners manual to add recommended fuel to engine Connect Hose and Water Supply to Pump IMPORTANT To avoid pump damage you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine 3 Before you connect your garden hose to the water inlet inspect the inlet screen Figure 7 Clean the screen if it contains debris or have it replaced if damaged Refer to the section O Ring Maintenance on page 13 if the inlet screen is damaged DO NOT RUN THE PRESSURE WASHER IF THE INLET SCREEN IS DAMAGED www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Speed Clean 2500 PSI Pressure Washer Briggs amp Stratton POWER PRODUCTS 6 Turn ON the water and squeeze the trigger on the gun to purge the pump system of air and impurities Inspect inlet Q screen DO NOT 1 CAUTION Before starting the pressure washer use if damaged Ns clean if dirty be sure you are wearing adequate eye protection CHECKLIST BEFORE STARTING ENGINE Review the unit s assembly to ensure you have performed all of the following IMPORTANT DO NOT siphon standing water for the I water supply Use ONLY cold wa
9. Know its applications its limitations and any hazards involved Every effort has been made to ensure that information in this manual is accurate and current However we reserves the right to change alter or otherwise improve the product and this document at any time without prior notice SAFETY RULES This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death The safety alert symbol is used with a signal word DANGER CAUTION WARNING a pictorial and or a safety message to alert you to hazards DANGER indicates a hazard which if not avoided will result in death or serious injury WARNING indicates a hazard which if not avoided could result in death or serious injury CAUTION indicates a hazard which if not avoided might result in minor or moderate injury CAUTION when used without the alert symbol indicates a situation that could result in equipment damage Follow safety messages to avoid or reduce the risk of injury or death In the State of California a spark arrester is required by law Section 4442 of the California Public Resources Code Other states may have similar laws Federal laws apply on federal lands If you equip the muffler with a spark arrester it must be maintained in effective working order Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 49
10. PRODUCTS A ADVERTENCIA A ADVERTENCIA PA 4 y La gasolina y sus vapores son extremadamente a El arrancador y otras piezas que rotan pueden inflamables y explosivos enredar las manos el pelo la ropa o los accesorios El fuego o una explosi n pueden causar quemaduras severas e inclusive la muerte e NO use ropa suelta joyas o elementos que puedan quedar atrapados CUANDO A ADA COMBUSTIBLE en el arranque o en otras partes rotatorias Apague el generador posici n OFF y d jelo enfriar al menos por a pelo largo y Sue Ie joyeria 2 minutos antes de remover la tapa de la gasolina Llene el tanque al aire libre NO Ilene demasiado el tanque Permita al menos espacio para la A ADVE RTENCIA expansion del combustible Mantenga la gasolina alejada de chispas llamas abiertas pilotos calor y El rociado de alta presi n puede hacer que particulas otras fuentes de ignici n peque as de pintura u otras part culas salgan gcd disparadas y viajen a altas velocidades NO encienda un cigarrillo o fume CUANDO OPERE EL EQUIPO e Siempre use protecci n para los ojos cuando utilice este equipo o NO incline el motor o el equipo de tal manera que la gasolina se cuando est cerca de donde se est usando el equipo pueda derramar NO rocie l quidos inflamables CUANDO TRANSPORTE O REPARE EL EQUIPO e Transporte o repare el equipo con el tanque de combustible vac o o con la v lvula para apagar el combustible apagada
11. motor y las bater as para el encendido est n garantizados por el fabricante de esos productos EL REGISTRO DE LA GARANT A NO ES NECESARIO PARA OBTENER LA GARANT A EN LOS BRIGGS amp STRATTON POWER PRODUCTS GUARDE SU RECIBO DE COMPRA SI USTED NO PROVEE LA PRUEBA DE LA FECHA DE LA COMPRA INICIAL AL MOMENTO EN QUE SE REQUIERA USAR LA GARANT A LA FECHA DE LA FABRICACI N DEL EQUIPO SER USADA PARA DETERMINAR EL PERIODO DE GARANT A Acerca de la seguridad de su equipo Nosotros reciben las reparaciones bajo la garant a y le pide disculpas por cualquier inconveniencia causada Cualquier Concesionario de Servicio Autorizado puede llevar a cabo reparaciones bajo la garant a La mayor a de las reparaciones bajo la garant a son manejadas normalmente pero algunas veces la solicitud del servicio de garant a es posible que no sea apropiada Por ejemplo la garant a no ser v lida si el da o al equipo ocurri debido al mal uso falta de mantenimiento adecuado manejo env o almacenamiento o una instalaci n inadecuada De manera similar la garant a queda anulada si se ha borrado la fecha de fabricaci n o el n mero de serie del equipo o si el equipo ha sido alterado o modificado Durante el per odo de la garant a el Comerciante Autorizado del Servicio hace en es la opci n la reparaci n o reemplaza cualquier parte eso sobre el examen se encuentran para ser defectuoso bajo el uso y el servicio normales Esta garant a no cubrir las rep
12. pressure spray to avoid injury if gun kicks back www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 ISAFETY RULES Speed Clean 2500 PSI Pressure Washer A WARNING sg Fuel and its vapors are extremely flammable and y explosive Fire or explosion can cause severe burns or WHEN ADDING FUEL Turn pressure washer OFF and let it cool at least 2 minutes before removing gas cap Fill fuel tank outdoors DO NOT overfill tank Allow space for fuel expansion Keep fuel away from sparks open flames pilot lights heat and other ignition sources DO NOT light a cigarette or smoke WHEN OPERATING EQUIPMENT e DO NOT tip engine or equipment at angle which causes fuel to spill e DO NOT spray flammable liquids WHEN TRANSPORTING OR REPAIRING EQUIPMENT e Transport repair with fuel tank EMPTY or with fuel shutoff valve OFF WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK e Store away from furnaces stoves water heaters clothes dryers or other appliances that have pilot light or other ignition source because they can ignite fuel vapors A WARNING The high pressure stream of water that this equipment produces can pierce skin and its Zag underlying tissues leading to serious injury and possible amputation NEVER aim the spray gun at people animals or plants DO NOT allow CHILDREN to operate the pressure washer e NEVER repair high pressure ho
13. pueda existir PELIGRO indica un riesgo el cual si no se evita causar la muerte o una herida grave ADVERTENCIA indica un riesgo el cual si no se evita puede causar la muerte o una herida grave PRECAUCI N indica un riesgo el cual si no se evita puede causar heridas menores o moderadas PRECAUCI N cuando se usa sin el s mbolo de alerta indica una situaci n que podr a resultar en el da o del equipo Siga los mensajes de seguridad para evitar o reducir los riesgos de heridas e inclusive la muerte En el estado de California es obligatorio seg n la ley el uso de apagachispas Secci n 4442 del C digo de Recursos P blicos de California Otros estados pueden tener leyes similares Las leyes federales se aplican en tierras federales Si equipa el silenciador con un apagachispas este deber ser mantenido en buenas condiciones de trabajo Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 A ADVERTENCIA El escape del motor de este producto contiene elementos qu micos reconocidos en el Estado de California por producir c ncer defectos de nacimiento u otros da os de tipo reproductivo A PELIGRO Al motor funcionar se produce mon xido de carbono un gas inodoro y venenoso El respirar el mon xido de carbono producir n usea desmayo o la muerte Opere el lavadora de presi n SOLAMENTE al aire libre Utilice un respirador o m scara siempre que exista la pos
14. unidad No podr funcionar La garant a no cubre el da o de la unidad ocasionado por congelamiento PRECAUCI N Lea y siga todo advierte y las advertencias en el PumpSaver pueden marcar Siempre protecci n de ojo de uso cuando se usa PumpSaver Al uso el PumpSaver cerci rese la arandela de la presi n se apaga y desconecta del agua del suministro Lea y siga todas instrucciones y las advertencias dadas en el contenedor de PumpSaver NOTA PumpSaver gotear de la bomba despu s que el tratamiento y manchar madera y cemento NOTA Si el PumpSaver no est disponible ponga anticongelante RV que no contenga alcohol en la bomba en una secci n de 3 pies de la manguera del jard n conectada a un adaptador y halando la manecilla dos veces ALMACENANDO EL MOTOR Consulte el manual del propietario del motor para las instrucciones de c mo preparar adecuadamente el motor para su almacenamiento www mymowerparts com Briggs amp Stratton POWER PRODUCTS Lavadora de Presi n 2500 PSI de Speed Clean REPARACION DE AVERIAS Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 REPARACION DE AVER AS Problema Causa Soluci n La boquilla est en el modo de baja I Mueva la boquilla hacia atr s para el modo de alta presi n presi n La bomba presenta los siguientes problemas no produce presi n produce una presi n errada traqueteo p rdida de presi n baj
15. 83 SAFETY RULES A WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm A DANGER Running engine gives off carbon monoxide an odorless colorless poison gas Some chemicals or detergents may be harmful if inhaled or ingested causing severe nausea fainting or poisoning Breathing carbon monoxide will cause nausea fainting or death Operate pressure washer ONLY outdoors Use a respirator or mask whenever there is a chance that vapors may be inhaled Read all instructions with mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors A WARNING wy Spray contact with electrical wiring can result in e GET e Keep water spray away from electric wiring or fatal electric shock may result A WARNING O Use of pressure washer can create puddles and slippery surfaces High pressure spray could cause you to fall if you are too close to the cleaning surface Keep spray nozzle between 8 to 24 inches away from cleaning surface Operate this unit on a stable surface The cleaning area should have adequate slopes and drainage to reduce the possibility of a fall due to slippery surfaces Be extremely careful if you must use the pressure washer from a ladder scaffolding or any other relatively unstable location Firmly grasp spray gun with both hands when using high
16. B3264AGS 14 94804GS 15 192317GS 16 23139DGS 17 189943GS 900 NSP Description KIT Hook KIT Hook KIT E Ring WAND Adjustable Nozzle ORIFICE KIT Wheel KEY ASSY Pump see page 7 ENGINE www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Speed Clean 2500 PSI Pressure Washer Briggs amp Stratton POWER PRODUCTS Item Part Description Item Part Description 190568GS SEAL 76 21783GS THERMAL RELIEF 3 190569GS RETAINER RING 77 190585GS OIL BOTTLE 9 190671GS ENGINE ADAPTER amp BEARING A 190672GS KIT WOBBLE PLATE BEARING 19 190571GS CAP Oil B 190670GS KIT WATER INLET 23 190573GS PISTON HOUSING D 190590GS KIT PISTON 28 190673GS MANIFOLD E 190591GS KIT CHECK VALVES 29 190575GS O RING F 190592GS KIT INLET CHECK 30 190576GS SCREW Venturi G 190593GS KIT CHEMICAL INJECTION 34 190577GS CONNECTION Chemical Inlet H 190594GS KIT UNLOADER 45 190578GS PIN J 189971GS KIT CHEMICAL HOSE 46 190579GS VALVE Seat Plate Brass K 190595GS KIT SEAL SET 47 190580GS VALVE Seat Stainless L 190596GS KIT HEAD BRASS 62 190581GS CAP M 190669GS KIT BREATHER TUBE 68 190582GS BALL Stainless Steal NOTE Item letters A M are service kits and include all 69 190584GS O RING parts shown within the box 32 17 www mymowerparts com Lavadora de Presi n 2500 PSI de Speed Clean Briggs Stratton POWER PRODUCTS TABLA
17. Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 amp Pp E gE d C Y a9 TR l by Briggs amp Stratton POWER PRODUCTS Pressure Washer 2Z2500PSI Owner s Manual Manual del Propietario Questions Help is just a moment away Preguntas La ayuda es justa un momento lejos Call Pressure Washer Helpline Llame L nea Directa del Lavador a Presi n 1 800 743 4115 M F 8 5 CT SpeedClean is a trademark of Briggs amp Stratton Power Products SpeedClean es una marca registrada de Briggs amp Stratton Power Products BRIGGS amp STRATTON POWER PRODUCTS GROUP LLC JEFFERSON WISCONSIN U S A Model No 1910 0 2500 PSI Pressure Washer Manual No 192427GS Revision 0 12 20 2002 www mymowerparts com Speed Clean 2500 PSI Pressure Washer Briggs Stratton POWER PRODUCTS TABLE OF CONTENTS Safety RulES 0000 ato aa 2 3 Know Your Pressure Washer o oo ooooooo mo 4 ASSEMBLY an erame ea aaa ie 5 7 Operation sitan ee a E ER ide 8 10 Product Specifications oooooooooo oo li Maintenance seriats ts eee pr win las 11 13 StOrases ia rra cols A eee a 13 Troubleshooting 0 cee ee eee eee eee ee 14 NS ca teak eed oe hd ea pedal aed aetna 15 Replacement Parts 00 00 0000 ee eee 16 17 Warranty iia is ad g a Last Page EQUIPMENT DESCRIPTION Read this manual carefully and become LL familiar with your pressure washer
18. DUCTS EQUIPMENT SAVE YOUR PROOF OF PURCHASE RECEIPT IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED THE MANUFACTURING DATE OF THE EQUIPMENT WILL BE USED TO DETERMINE THE WARRANTY PERIOD About your equipment warranty We welcome warranty repair and apologize to you for being inconvenienced Any Authorized service dealer may perform warranty repairs Most warranty repairs are handled routinely but sometimes requests for warranty service may not be appropriate For example warranty service would not apply if equipment damage occurred because of misuse lack of routine maintenance shipping handling warehousing or improper installation Similarly the warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered or modified During the warranty period the Authorized service dealer at its option will repair or replace any part that upon examination is found to be defective under normal use and service This warranty will not cover following repairs and equipment Normal Wear Outdoor power equipment like all mechanical devices needs periodic parts service and replacement to perform well This warranty does not cover repair when normal use has exhausted the life of a part or the equipment Installation and Maintenance This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized in
19. ER PRODUCTS PREPARANDO LA UNIDAD PARA SU ALMACENAMIENTO El agua no debe permanecer en la unidad por un largo periodo de tiempo Los sedimentos o minerales se pueden depositar en las piezas de la bomba y congelar la acci n de la bomba Si usted no piensa usar el lavador a presi n por mas de 30 d as siga este procedimiento Vac e el tubo de detergente colocando el filtro en un envase lleno de agua limpia mientras est corriendo el agua a baja presi n la lanza ajustable en la posici n hacia adelante Lave por o 2 minutos 2 Apague el motor y permita refrescar entonces quita mangas altas de presi n y jard n Desconecte el alambre de la buj a 3 Vac e todos los l quidos presentes en la bomba halando la manecilla de retroceso hasta seis veces Esto deber a remover la mayor parte de los l quidos presentes en la bomba 4 El salvador de la bomba de la marca del uso a previene la corrosi n construye y helado de bomba 5 Almacene la unidad en un lugar limpio y seco Proteger la Bomba A protege al PumpSaver de uso de bomba a previene congelar el da o y lubrica mbolos y sellos NOTA El PumpSaver est n disponible s lo como un accesorio opcional No es incluido con la arandela de la presi n Avise el m s cercano servicio autorizado central para comprar PumpSaver PRECAUCI N Usted deber proteger su unidad de las temperaturas de congelamiento Si No lo hace da ar permanentemente la bomba y la
20. ION IS PERMITTED BY LAW Some countries or states do not allow limitations on how long an implied warranty lasts and some countries or states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation and exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from country to country or state to state WARRANTY PERIOD Equipment Consumer Use Commercial Use Pressure Washer Year 90 Days Water Pump Portable Generator 2 Years Home Generator System Less than 10 KW 2nd year parts only Includes Transfer Switch if supplied Home Generator System 10 KW or greater 3 years or 1500 hours 3 years or 1500 hours Includes Transfer Switch if supplied The warranty period begins on the date of purchase by the first retail consumer or commercial end user and continues for the period of time stated in the table above Consumer use means personal residential household use by a retail consumer Commercial use means all other uses including use for commercial income producing or rental purposes Once equipment has been used commercially it shall thereafter be considered to be in commercial use for purposes of this warranty The engine and starting batteries are warranted solely by the manufacturers of those products WARRANTY REGISTRATION IS NOT NECESSARY TO OBTAIN WARRANTY ON BRIGGS amp STRATTON POWER PRO
21. SE If you have any problems with the assembly of your pressure washer or if parts are missing or damaged call the pressure washer helpline at 1 800 743 4115 If calling for assistance please have the model revision and serial number from the data tag available To prepare your pressure washer for operation you will need to perform these tasks Fill out and send in registration card Attach handle to main unit Add fuel to the fuel tank Connect the high pressure hose to the spray gun and the pump 2 3 Add oil to the engine crankcase 4 5 gs Connect the water supply to the pump 7 Attach nozzle extension to spray gun Speed Clean 2500 PSI Pressure Washer Briggs amp Stratton POWER PRODUCTS Attach Handle Place the handle assembly onto the handle supports connected to the main unit Make sure the holes in the handle align with the holes on the handle supports Figure 1 Figure Attach Handle to Base Handle Handle Supports NOTE It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports 2 Insert the carriage bolts through the holes from the outside of the unit and attach a plastic knob from the inside of the unit Figure 2 Tighten by hand Figure 2 Secure Handle 3 Insert one of the L hooks through the hole just under the billboard on the left side of the handle viewi
22. Start the engine according to instructions given in the engine owner s manual NOTE If the recoil starter is hard to pull squeeze the spray gun trigger to relieve internal pump pressure How to Stop Your Pressure Washer Let the engine idle for two minutes 2 Turn engine off according to instructions given in the engine owner s manual 3 Squeeze trigger on the spray gun to relieve pressure in the hose NOTE A small amount of water will squirt out when you release the pressure www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 OPERATION gt AA ie IS How to Use the Adjustable Nozzle You should now know how to START and STOP your pressure washer The information in this section will tell you how to adjust the spray pattern and to apply detergent or other cleaning chemicals WARNING NEVER adjust spray pattern when spraying NEVER put hands in front of nozzle to adjust spray pattern I Slide the nozzle forward when you wish to adjust the spray to low pressure mode Figure 10 Slide the nozzle backward to achieve high pressure Figure 10 Adjusting Nozzle for Pressure Slide nozzle backward for High Pressure Mode Slide nozzle forward for low pressure mode and detergent application 2 Point the nozzle down towards a firm surface and press the trigger to test the pattern Figure 1 Figure Testing the Spray Pattern
23. aci n del detergente Mueva la boquilla hacia atr s para obtener el modo de alta presi n 2 Apunte la boquilla hacia el suelo desenganche el cerrojo de seguridad y apriete el gatillo para probar el patr n de rociado Figura 25 Figura 25 Poner a Prueba el Patr n de Aspersi n ETS Lavadora de Presi n 2500 PSI de Speed Clean Briggs amp Stratton POWER PRODUCTS 3 El patr n de rociado se ajusta de un patr n angosto a un patr n en abanico girando la boquilla Figura 26 Figura 26 Ajustar el Patr n de Aspersi n Gire la boquilla en sentido contrario a las manecillas del reloj para un patr n de rociado en abanico Gire la boquilla en sentido de las manecillas del reloj para un patr n de rociado a chorro 4 Para una limpieza m s efectiva mantenga la boquilla de rociado de 8 a 24 pulgadas de la superficie de limpieza 5 Si coloca la boquilla de rociado demasiado cerca podr a da ar la superficie especialmente cuando est usando el modo de alta presi n 6 NO coloque la boquilla a menos de 6 pulgadas cuando est limpiando llantas Aplicaci n del Detergente Usando la Boquilla Ajustable IMPORTANTE Utilice qu micos dise ados espec ficamente para m quinas lavadoras a presi n Los detergentes caseros podr an da ar la bomba PRECAUCI N Usted deber conectar todas las mangueras antes de darle arranque al motor Arrancar el motor sin tener todas las mangueras conect
24. adas y sin el suministro de agua ABIERTO ON causar el da o de la bomba Para aplicar el detergente siga los siguientes pasos I Revise el uso de la boquilla ajustable 2 Prepare la soluci n detergente siguiendo las instrucciones del fabricante 3 Coloque el peque o extremo final del filtro del tubo de inyecci n del detergente dentro del contenedor del detergente PRECAUCION Evite que el tubo de inyecci n de qu micos entre en contacto con el silenciador caliente www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Lavadora de Presi n 2500 PSI de Speed Clean Briggs Stratton POWER PRODUCTS Mueva la boquilla ajustable hacia adelante para obtener el modo de baja presi n El detergente no puede ser aplicado si tiene la boquilla en la posici n de alta presi n 5 Aseg rese que la manguera de jard n est conectada a la entrada del agua Revise que la manguera de alta presi n est conectada a la pistola de rociado y a la bomba Dele arranque al motor 6 Aplique el detergente sobre la superficie seca comenzando en la parte inferior del rea y dirigi ndose hacia arriba utilizando movimientos largos parejos y superpuestos Permita que el detergente penetre de 3 a 5 minutos antes de enjuagar Vuelva a aplicarlo cuando sea necesario para evitar que la superficie se seque NO permita que el detergente se seque Si permite que el dete
25. anguera de alta presi n www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 IMPORTANTE Lea totalmente el manual del propietario antes que intente ensamblar u operar su lavador a alta presi n REMUEVA EL LAVADOR A ALTA PRESI N DEL EMPAQUE Remueva la bolsa con las piezas accesorios y las adiciones incluidas con el lavador de presi n 2 Corte dos esquinas en los extremos del cart n desde la parte superior hasta la parte inferior de tal manera que el p nel pueda ser doblado en forma plana 3 Remueva el lavador a presi n del la caja Contenido de la Caja Los Art culos que se Encuentran en la Caja Son Unidad principal e Manubrio e Manguera de alta presi n e Pistola rociadora e Extensi n de la lanza Gafas de Seguridad Botella de aceite para motor e Bolsa de accesorios incluye lo siguiente Manual del propietario Manual del motor Tarjeta de registro del propietario Accesorios para adherir el manubrio PREPARANDO EL LAVADOR A ALTA PRESI N PARA SU USO Si usted tiene un problema al ensamblar la unidad o si hacen falta algunas piezas o se encuentran da adas llame a la l nea directa del lavador a alta presi n al 1 800 743 4115 Si llamar para la ayuda tiene por favor el modelo la revisi n y el n mero de serie de la etiqueta de datos disponible A prepara su arandela de la presi n para la operaci n usted nec
26. ar kinking or abuse Inspect the hose each time before using it Check for cuts leaks abrasions or bulging of cover damage or movement of couplings If any of these conditions exist replace the hose immediately Replace it with another hose that exceeds the maximum pressure rating of your pressure washer 1 WARNING NEVER repair a high pressure hose Check Chemical Injection Hose Examine the filter on the detergent tube and clean if clogged The tube should fit tightly on the barbed fitting Examine the tube for leaks or tears Replace the filter or tube if either is damaged Check Gun and Adjustable Nozzle Extension Examine the hose connection to the spray gun and make sure it is secure Test the trigger by pressing it and making sure it springs back into place when you release it Put the safety latch in the ON position and test the trigger You should not be able to press the trigger Purge Pump of Air and Contaminants To remove air from the pump follow these steps Set up the pressure washer as described in Preparing Pressure Washer For Use Connect the water supply and turn water on 2 Pull the trigger on the spray gun and hold 3 When the water supply is steady and constant engage the safety latch www mymowerparts com Speed Clean 2500 PSI Pressure Washer Briggs amp Stratton POWER PRODUCTS To remove contaminants from the pump follow these steps Set up the pressu
27. araciones y el equipo siguientes e Desgaste normal Equipo el ctrico al aire libre como todos los aparatos mec nicos necesita partes servicio y reemplazo peri dicamente para que funcione bien Esta garant a no cubre la reparaci n cuando el uso normal ha acabado con la vida de una parte en particular o del equipo e Instalaci n y mantenimiento Esta garant a no se aplica al equipo o parte que ha estado sujeta a una instalaci n inadecuada que no haya sido autorizada o a cualquier tipo de alteraci n el mal uso negligencia accidentes sobrecarga velocidad excesiva mantenimiento inadecuado reparaci n o almacenamiento en nuestro juicio han afectado desfavorablemente su rendimiento y fiabilidad Esta garant a tambi n no cubre el mantenimiento normal tales como ajustes limpieza del sistema de combusti n y la obstrucci n debido a materias qu micas suciedad carb n o cal etc e Otras exclusiones Tambi n se encuentran excluidos de est garant a el desgaste de los art culos tales como conectadores medidores de aceite correas anillos O filtros empaque de la bomba etc las bombas que se hagan funcionar o trabajar sin agua o da os y malfuncionamientos que resulten de accidentes abusos modificaciones alteraciones un servicio inadecuado congelamiento o deterioro qu mico Los accesorios tales como pistolas mangueras varillas y boquillas est n excluidos de la garant a del producto Tambi n se excluye el equipo usado
28. arte superior del rea que va a enjuagar dirigi ndose hacia abajo con los mismos movimientos superpuestos que utiliz para el limpieza Sistema de Enfriamiento Autom tico Alivio T rmico El agua que circula dentro de la bomba puede alcanzar temperaturas entre los 125 155 F si hace funcionar el motor de su m quina lavadora a presi n de 3 a 5 minutos sin oprimir el gatillo de la pistola de rociado Cuando el agua alcanza dicha temperatura el sistema de enfriamiento autom tico se activa y enfr a la bomba descargando agua caliente en el piso Este sistema evita el da o interno de la bomba www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 N ESPECIFICACIONES Presi n de Salida 2500 PSI Promedio de Flujo 2 4 galones por minuto gpm Detergente Use el detergente adecuado para lavadores a presi n Temperatura del Suministro de Agua Que no pase de 1009F Sistema de Funcionar cuando el agua alcance de Enfriamiento 125 155 Autom tico Peso que Embarca 54 lbs RECOMENDACIONES GENERALES La garant a de la m quina lavadora a presi n no cubre los elementos que han sido sujetos a abuso o negligencia por parte del operador Para hacer v lida la cobertura total de la garant a el operador deber mantener la lavadora de presi n tal y como se indica en el manual Algunos ajust
29. ay gun trigger may be caused by excessive pump pressure The principal cause of excessive pump pressure is a nozzle clogged or rest ricted with foreign materials such as dirt etc To correct the problem immediately clean the nozzle using the tools included with your pressure washer and follow these instructions Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 MAINTENANCE Shut off the engine and turn off the water supply Detach the nozzle extension from the spray gun Twist the nozzle clockwise to the stream position Using the supplied 2mm 5 64 allen wrench remove the orifice from the end of the nozzle extension Figure 15 Figure 15 Removing and Cleaning Orifice N lt L one Ou Remove the in line filter from the other end of the nozzle extension Use the wire included in the kit or a small paper clip to free any foreign material clogging or restricting the orifice Figure 15 Using a garden hose remove additional debris by back flushing water through the nozzle extension Figure 16 Back flush between 30 to 60 seconds Turn the adjustable nozzle extension to stream spray and move the nozzle from low to high while flushing Figure 16 Backflushing the Nozzle Reinstall the orifice and in line filter into the nozzle extension DO NOT overtighten the orifice with the allen wrench Reconnect the nozzle extension to the spray gun Reconnect t
30. con agua limpia para eliminar toda clase de residuos Extensi n de la Boquilla 2 Si el colador est da ado encontrar un colador para el filtro en l nea y un anillo o de repuesto en el juego de anillos o Si no est da ado vuelva a usarlo 3 Coloque el colador del filtro en l nea en el extremo con rosca de la extensi n para boquillas Su direcci n no importa Coloque el colador ejerciendo presi n con el borrador de un l piz hasta que se asiente por completo en el fondo de la abertura Tenga cuidado de no doblar el colador 4 Coloque el anillo o en la ranura respectiva Empuje el anillo o hasta que quede ajustado contra el colador del filtro en l nea 5 Conecte la extensi n para boquillas a la pistola de rociado de la manera descrita anteriormente en este manual Mantenimiento de las Boquillas Si siente una sensaci n pulsante al momento de apretar el gatillo de la pistola rociadora puede que sea causada por la presi n excesiva en la bomba La causa principal de la presi n excesiva en la bomba es cuando la boquilla se encuentra atascada o tapada con materiales extra os tales como tierra etc Para corregir el problema limpie inmediatamente la boquilla usando las herramientas incluidas con su lavador a presi n y siga las instrucciones siguientes Apague el motor y apague el suministro de agua 2 Separe la extensi n de la boquilla de la pistola rociadora Gire la boquilla en direcci n de las a
31. de agua y prenda agua 2 Estire el disparador en el fusil del roc o y el asidero 3 Cuando el agua es constante y constante compromete el picaporte de la seguridad Para retirar los contaminantes de la bomba siga los siguientes pasos l Instale la m quina lavadora a presi n como est descrito en Preparando El Lavador A Alta Presi n Para Su Uso Conecte el abastecimiento de agua y prenda agua 2 Quite boquilla la extensi n del fusil del roc o 3 Ponga en marcha el motor de acuerdo a las instrucciones de C mo Darle Arranque a su M quina Lavadora a Presi n 4 Hale el gatillo de la pistola y mant ngalo apretado Cuando el suministro de agua sea uniforme y constante enganche el cerrojo de seguridad y vuelva a ajustar la extensi n para boquillas www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Lavadora de Presi n 2500 PSI de Speed Clean Briggs Stratton POWER PRODUCTS Revise el Filtro en L nea Consulte la Figura 27 y suministre servicio al filtro en l nea si se tapa siguiendo estos pasos Figura 27 Limpieza del Filtro Filtro en L nea Anillo O Retire la pistola y la extensi n para boquillas de la manguera de alta presi n Retire la extensi n para boquillas de la pistola y retire el anillo o y el colador de la extensi n para boquillas Lave el colador pistola y extensi n para boquillas
32. del motor para a adir al motor el combustible recomendado Conecte la Manguera y el Suministro de Agua a la Bomba IMPORTANTE Usted deber armar la extensi n para boquillas y conectar todas las mangueras antes de darle arranque al motor La bomba resultar da ada si arranca el motor sin tener todas las mangueras conectadas y el suministro agua abierto Retroceda la manguera a alta presi n y conecte a la base de la pistola rociadora Figura 19 Apriete con la mano Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Figura 19 Conecte la Manguera a alta Presi n a la Pistola Rociadora Conecte aqu la manguera a alta presi n Conecte el otro extremo de la manguera a alta presi n a la salida de alta presi n de la bomba Figura 20 Apriete con la mano Figura 20 Conectar la Manguera de Alta Presi n a la Toma Antes de que conecte la manguera de jard n a la entrada de agua inspeccione el colador de la entrada Figura 21 Limpie el colador si tiene residuos o solicite su remplazo si est da ado Refi rase a la secci n Mantenimiento de los Anillos O en la p gina 28 si la colador de la entrada se da ado NO HAGA FUNCIONAR LA M QUINA LAVADORA A PRESI N SI EL COLADOR DE LA ENTRADA EST DA ADO www mymowerparts com Figura 21 Conectar la Manguera del Jard n a la Entrada de ces Inspeccione la rejilla de entrada NO la use si e
33. depositado aceite y est al nivel correcto en la caja del cigie al del motor Deposite la gasolina adecuada en el tanque del combustible 4 Revise que todas las conexiones de las mangueras alta presi n y suministro de agua est n apretadas correctamente y que no existan dobleces cortes o da o de la manguera de alta presi n Proporcione el suministro de agua adecuado Aseg rese de leer las secciones Reglas de Seguridad y C mo Usar Su M quina Lavadora A Presi n antes de usar la m quina lavadora a presi n www mymowerparts com Lavadora de Presi n 2500 PSI de Speed Clean Briggs Stratton POWER PRODUCTS C MO USAR SU M QUINA LAVADORA A PRESI N Si tiene problemas operando su m quina lavadora a presi n por favor llame a la l nea de ayuda para m quinas lavadoras a presi n al 1 800 743 4115 C mo Darle Arranque a su M quina Lavadora a Presi n Para darle arranque a su m quina lavadora a presi n movida a motor por primera vez siga estas instrucciones paso a paso Esta informaci n acerca del arranque inicial tambi n se aplica cuando vaya a darle arranque al motor despu s de haber dejado de la m quina lavadora a presi n fuera de uso por al menos un d a I Coloque la m quina lavadora a presi n en un rea cercana a una suministro de agua exterior capaz de abastecer agua a un volumen mayor de 3 0 galones por minuto en no menos que 20 PSI en el fin de arandela de presi n de la ma
34. em number 190585GS by contacting the nearest authorized service center Change pump oil as follows Drain engine oil and fuel from pressure washer Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Speed Clean 2500 PSI Pressure Washer Briggs amp Stratton POWER PRODUCTS 2 Use a 8mm allen wrench to remove the black pump oil cap between the high pressure outlet and garden hose inlet Figure 14 Figure 14 Changing Pump Oil 3 Tilt the pressure washer to drain the oil into an approved container until it drips slowly from the pump 4 Tilt the pressure washer in the opposite direction and empty the premeasured pump oil bottle into the same opening a small funnel may be helpful 5 Install the black pump oil cap and tighten firmly 6 Set the pressure washer in the upright position Add fuel and engine oil ENGINE MAINTENANCE See the engine owner s manual for instructions on how to properly maintain the engine CAUTION Avoid prolonged or repeated skin A contact with used motor oil Used motor oil has been shown to cause skin cancer in certain laboratory animals Thoroughly wash exposed areas with soap and water KEEP OUT OF REACH OF CHILDREN DON T POLLUTE CONSERVE RESOURCES RETURN USED OILTO COLLECTION CENTERS www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Speed Clean 2500 PSI Pressu
35. ence To receive full value from the warranty the operator must maintain the pressure washer as instructed in this manual e Some adjustments will need to be made periodically to properly maintain your pressure washer All maintenance in this manual and the engine owner s manual should be made at least once each season Once a year you should clean or replace the spark plug clean or replace the air filter and check the spray gun and adjustable nozzle extension assembly for wear A new spark plug and clean air filter assure proper fuel air mixture and help your engine run better and last longer Please refer to your engine owner s manual for more details If equipped with inflatable tires keep the air pressure at the value marked on the tire or within 15 and 40 psi Before Each Use Check engine oil level Check water inlet screen for damage Check in line filter for damage Check high pressure hose for leaks Check chemical injection hose and filter for damage 95 UT A UN Check spray gun and adjustable nozzle extension assembly for leaks 7 Rinse out garden hose to flush out debris Speed Clean 2500 PSI Pressure Washer Briggs amp Stratton POWER PRODUCTS PRESSURE WASHER MAINTENANCE Check and Clean Inlet Screen Examine the screen on the water inlet Clean it if the screen is clogged or replace it if screen is damaged Check High Pressure Hose The high pressure hose can develop leaks from we
36. ered under warranty warnings on the PumpSaver can label Always wear eye protection when using PumpSaver 1 CAUTION Read and follow all cautions and To use PumpSaver make sure the pressure washer is turned off and disconnected from supply water Read and follow all instructions and warnings given on the PumpSaver container NOTE PumpSaver will drip from pump after treatment and will stain wood and concrete NOTE If PumpSaver is not available draw RV antifreeze non alcohol into the pump by pouring the solution into a 3 foot section of garden hose connected to inlet adapter and pulling recoil handle twice STORING THE ENGINE See the engine owner s manual for instructions on how to properly prepare the engine for storage www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 TROUBLE SHOOTING Speed Clean 2500 PSI Pressure Washer TROUBLESHOOTING Problem Cause Briggs amp Stratton POWER PRODUCTS Correction Nozzle in low pressure mode Pull nozzle backward for high pressure mode 2 Water inlet is blocked 2 Clear inlet Pump has following 3 Inadequate water supply l 3 Provide adequate water flow 4 Inlet hose is kinked or leaking 4 Straighten inlet hose patch leak problems failure to i A 5 Clogged inlet hose strainer 5 Check and clean inlet hose strainer produce pressure erratic A b a e chatt
37. ering lo 6 Water supply is over 100 F 6 Provide cooler water supply nic a 1 High pressure hose is blocked or 7 Clear blocks in outlet hose of pressure low water leaks volume 8 Gun leaks 8 Replace gun 9 Nozzle is obstructed 9 Clean nozzle 10 Pump is faulty 10 Contact Briggs and Stratton service facility Detergent siphoning tube is not Insert detergent siphoning tube into submerged detergent Detergent fails to mix 2 Chemical filter is clogged or cracked 2 Clean or replace filter detergent with spray siphoning tube 3 Dirty in line filter 3 See Check In Line Filter on page 12 4 Nozzle is in high pressure mode 4 Push nozzle forward for low pressure mode Pressure washer stops Out of gasoline Fill fuel tank during operation www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Speed Clean 2500 PSI Pressure Washer Briggs Stratton POWER PRODUCTS Item Part 192551GS BI91874GS 191909GS 190249GS 192318GS 192131GS B3263GS B2203GS 192310GS NN 00 Y 01 U71 h UY NN Description BASE HANDLE BILLBOARD HOSE KIT Engine Mounting Hardware KIT Pump Mounting Hardware GUN KIT Handle Connector KIT Vibration Mount Items Not Illustrated Part 192427GS 192552GS BB3061BGS Description MANUAL Owner s KIT Decals OIL Engine Item Part 10 192309GS II 192128GS 12 191265GS 13
38. es tendr n que hacerse peri dicamente para mantener adecuadamente su m quina lavadora a presi n Todos los servicios y ajustes deber n hacerse por lo menos una vez en cada estaci n Una vez al a o usted deber limpiar o remplazar la buj a y el filtro de aire Una buj a nueva y un filtro de aire limpio garantizan una mezcla de combustible aire adecuada y le ayuda a su motor a funcionar mejor y a tener una vida til m s prolongada Por favor para mayores detalles consulte el manual del propietario del motor e Si equip con llantas que se pode hinchar mantenga la presi n a rea en el valor marcado en la llanta o dentro de 15 y 40 psi Antes de Cada Uso Revise el nivel de aceite del motor Revise si existen da os en el colador de la entrada de agua Revise si existen da os en el filtro en l nea Revise si existen fugas en la manguera de alta presi n Revise si existen da os en los filtros de qu micos S Oe SNe Revise si existen fugas en el conjunto de la extensi n para boquillas y pistola 7 El aclarado fuera manga de jardin para limpiar fuera escombros MANTENIMIENTO DE LA MAQUINA LAVADORA A PRESION Revise y Limpie el Colador de Entrada Examine el colador de entrada de la manguera de jard n Limpielo si est tapado o remplacelo si est roto Lavadora de Presi n 2500 PSI de Speed Clean Briggs amp Stratton POWER PRODUCTS Revise la Manguera de Alta Presion Las mangueras de a
39. esitar a realiza estas tareas I Llene y mande en tarjeta de matr cula 2 Conecte manubrio a unidad principal 3 A ada aceite al motor 4 A ada gasolina al tanque de combustible 5 Conecte manguera a alta presi n a pistola rociadora y a bomba OS Conecte el suministro de agua a bomba Conecte boquilla la extensi n al pistola rociadora Lavadora de Presi n 2500 PSI de Speed Clean Briggs amp Stratton POWER PRODUCTS Conecte el Manubrio Coloque el manubrio sobre los soportes del mismo que ya est n adheridos a la unidad principal Aseg rese de que los orificios en el manubrio est n alineados con los orificios en los soportes del mismo manubrio Figura 15 Figura I5 Fijar el Manubrio a la Base Alinear Orificios Soportes del Manubrio NOTA Tal vez sera necesario mover los soportes del manubrio de un lado a otro para alinear el manubrio de tal manera que pueda deslizarse sobre los soportes del mismo manubrio 2 Inserte el perno del soporte a trav s de los orificios desde fuera de la unidad y sujete una perilla de pl stico desde el interior de la misma unidad Apriete manualmente Figura 16 Figura 16 Sujetar el Manubrio 3 Inserte el L gancho del agujero apenas bajo la cartelera en el izquierda de la manija visto desde la parte posterior de la unidad Sostenga el gancho en lugar con los alicates y asocie la tuerca de fijaci n con una llave del 7 16 Figura 17
40. estados no admiten limitaciones en cuanto a la vigencia de una garant a impl cita y algunos no admiten la exclusi n o limitaci n de da os resultantes o derivados Por lo tanto es posible que las limitaciones y exclusiones arriba mencionadas no se apliquen a su caso Esta garant a le otorga determinados derechos legales y es posible que usted cuente con otros derechos que pueden variar de un pa s a otro o de un estado a otro PERIODO DE GARANT A Equipo Para Uso Del Consumidor Para Uso Comercial Lavador a Presi n a o 90 d as Bomba de Agua Generador Port til 2 a os a o Sistemas de Generador Dom stico Menos de 10KW el segundo a o solamente para las partes incluye el conmutador de transferencia si suministr Sistemas de Generador Dom stico De 10KW o mayor 3a os o 1500 horas 3a os o 1500 horas incluye el conmutador de transferencia si suministr El periodo de garant a comienza en la fecha de compra hecha por el primer consumidor al detal o usuario comercial y contin a por el periodo de tiempo expres arriba Para uso del consumidor significa uso residencial por un consumidor al detal Para uso comercial significa todos los otros casos incluyendo el uso comercial para generar un ingreso o por prop sitos de alquiler Una vez que el equipo ha sido usado comercialmente deber a ser considerado como de uso comercial para las finalidades de esta garant a e El
41. gujas del reloj a la posici n stream chorro Usando la llave de Allen de 2mm 5 64 provista remueva la boquilla del extremo de la extensi n de la boquilla Figura 33 Figura 33 Remover y Limpiar la Boquilla NN gt 3 Quite el en el filtro de la linea del otro fin de la extensi n de boquilla 4 Use el alambre incluido en el juego o un peque o sujeta papeles para liberar cualquier material extra o que est tapando la boquilla Figura 33 5 Usando una manguera de jardin remueva cualquier desecho adicional poniendo agua en la extensi n de la boquilla Figura 34 Haga sto de 30 a 60 segundos Gire la extensi n de la boquilla ajustable a stream spray chorro rociador y mueva la boquilla de low bajo a high alto mientras drene el agua Figura 34 Suministrar Flujo de Agua a la Boquilla 6 Instale de nuevo la boquilla y en el filtro en l nea en la extensi n NO la apriete demasiado con la llave Allen 7 Conecte de nuevo la extensi n de la boquilla a la pistola rociadora 8 Conecte de nuevo el suministro de agua prenda el agua y encienda el motor 9 Pruebe el lavador a presi n al hacer funcionar la boquilla en la posici n high y low o con cada una de las boquillas de Conexiones r pidas que viene con el lavador a presi n Mantenimiento de los Anillos O Durante la operaci n normal de su m quina lavadora a presi n los anillos o mantienen apretadas y lib
42. he water supply turn on the water and start the engine Test the pressure washer by operating with nozzle in the high and in the low positions www mymowerparts com O Ring Maintenance Through the normal operation of your pressure washer o rings which keep the connections of the hoses and spray gun tight and leak free may become worn or damaged An O Ring Maintenance Kit is provided with your pressure washer which includes replacement o rings rubber washer and water inlet filter Refer to the instruction sheet provided in the kit to service your unit s o rings Note that not all of the parts in the kit will be used on your unit To remove a worn or damaged o ring e Use a small flathead screwdriver to get underneath the o ring and pry it off Cleaning Chemical Injection Hose If you used the chemical injection hose you must flush it with clean water before stopping the engine Place the chemical injection hose in a bucket full of clean water 2 Slide the adjustable nozzle forward to the low pressure position Flush for l 2 minutes 3 Shut off the engine IMPORTANT Simply shutting OFF engine will not release pressure in the system When the engine has shut down squeeze the trigger on the spray gun to relieve the pressure in the hose Pump Maintenance Changing Pump Oil Change oil every 50 hours or once yearly whichever occurs first NOTE Purchase a premeasured bottle of pump oil it
43. her Briggs Stratton POWER PRODUCTS Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 PRESSURE WASHER KNOW YOUR PRESSURE WASHER Read this owner s manual and safety rules before operating your high pressure washer Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and adjustments Save this manual for future reference Pump equipped with Automatic Cool Down System High Pressure Outlet Water Inlet Data Tag Adjustable Nozzle Always attached to nozzle extension Adjustable nozzle allows you to adjust spray pressure and spray pattern Air Filter Dry type filter element limits the amount of dirt and dust that gets in the engine Automatic Cool Down System Cycles water through pump when water reaches 25 155 F Warm water will discharge from pump onto ground This system prevents internal pump damage Chemical Injection Siphon Filter Use to siphon detergent or other pressure washer chemicals into the low pressure stream Choke Lever Prepares a cold engine for starting Data Tag Provides model revision and serial number of pressure washer Please have these readily available if calling for assistance wwe Th P Control Lever Recoil Starter Choke Lever Air Filter Chemical Injection Siphon Filter Oil Fill Dipstick Fuel Cap Fill tank
44. i figurent dans le manuel d utilisation NOTA En caso de que resulte dif cil jalar el arrancador de retroceso quiz s ser necesario apretar con firmeza el disparador de la pistola para disminuir la presi n interna de bombeo C mo Detener su M quina Lavadora a Presi n Espere que el motor descanse 2 Pour teindre le moteur suivez les instructions qui figurent dans le manuel d utilisation 3 Apriete el gatillo de la pistola de rociado para eliminar la presi n de la manguera NOTA Observar una peque a cantidad de agua cuando elimine la presi n 24 www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 OPERACION A gt nA C mo Usar la Boquilla Ajustable Usted ya debe saber como darle ARRANQUE a su m quina lavadora a presi n y como DETENERLA La informaci n de esta secci n le dir como ajustar el patr n de rociado y como aplicar detergente u otros qu micos de limpieza ADVERTENCIA NUNCA ajuste el patr n de rociado cuando est rociando NUNCA coloque las manos en frente de la boquilla para ajustar el patr n de rociado Usted tambi n puede ajustar el patr n de rociado girando la boquilla para que est concentrado en un patr n de chorro o un patr n expandido en abanico Figura 24 Figura 24 Ajustar la Presi n de Aspersi n Mueva la boquilla hacia adelante para obtener el modo de baja presi n y para la aplic
45. ibilidad de inhalar vapores Lea todas las instrucciones de la m scara para asegurarse de que le brindar la protecci n necesaria contra la inhalaci n de vapores nocivos A ADVERTENCIA WY El contacto del roc o con alambrado el ctrico puede tener como resultado electrocution e Mantenga el chorro del agua alejado de alambrados el ctricos de lo contrario podr an ocurrir descargas el ctricas fatales ADVERTENCIA El uso de lavadora de presi n puede crear los charcos y superficies resbalosas El rociado de la alta presi n podr a hacerlo caer si est muy cerca de la superficie de limpieza Mantenga la boquilla de rociado de 8 a 24 pulgadas de la superficie de limpieza Opere y almacene esta unidad sobre una superficie estable El rea de limpieza deber tener inclinaciones y drenajes adecuados para disminuir la posibilidad de ca das debido a superficies resbalosas Sea extremadamente cuidadoso si usa la m quina lavadora a presi n desde una escalera andamio o cualquier superficie relativamente inestable Sujete la pistola de la hidrolavadora firmemente con ambas manos cuando utilice el rociado a alta presi n De esta manera evitar lesiones producidas por el posible golpe de la pistola hacia atr s www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 REGLAS DE SEGURIDAD Lavadora de Presi n 2500 PSI de Speed Clean Briggs amp Stratton POWER
46. ible www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 POLITICA PARA EL PROPIETARIO DE EQUIPOS BRIGGS amp STRATTON POWER PRODUCTS Efectiva desde el Iro de Enero 2003 GARANTIA LIMITADA Briggs amp Stratton Power Products reparara o reemplazara sin cargo cualquier pieza o parte del equipo que se encuentre defectuosa tanto en lo concerniente a los materiales como a la mano de obra o a ambos Los gastos de transporte de las piezas enviadas para reparaci n o reemplazo cubiertas por esta garant a deber n ser pagadas por el comprador Esta garant a tiene vigencia durante el per odo de tiempo establecido por esta pol tica y est sujeta a las condiciones indicadas en la misma Para obtener servicio en garant a localice el distribuidor de servicio autorizado m s pr ximo llamando al 800 743 41 15 Los distribuidores de servicio autorizado de Briggs amp Stratton Power Products son los nicos que pueden ofrecer servicio en garant a NO EXISTE OTRA GARANT A EXPRESA LAS GARANT AS IMPL CITAS INCLUYENDO AQUELLAS DE MERCANTIBILIDAD O CAPACIDAD PARA UN PROP SITO PARTICULAR EST N LIMITADAS AL PERIODO DE TIEMPO ESPECIFICADO O HASTA EL L MITE PERMITIDO POR LA LEY TODA Y CUALQUIER GARANT A IMPL CITA EST EXCLUIDA RESPONSABILIDAD POR DA OS CONSECUENTES BAJO CUALQUIER Y TODAS LAS GARANT AS EST N EXCLUIDAS HASTA EL L MITE DE EXCLUSI N PERMITIDO POR LA LEY Algunos pa ses o
47. irculating water in the pump can reach a temperature 1 WARNING Be extremely careful if you must use between 25 155 F When the water reaches this 4 Start at the top of the area to be rinsed working down with same overlapping strokes as you used for washing and applying detergent the pressure washer from a ladder scaffolding or any temperature the automatic cool down system engages and other relatively unstable location When you press the cools the pump by discharging the warm water onto trigger the recoil from the initial spray could cause the ground This system prevents internal damage to the you to fall The high pressure spray could also cause pump you to fall if you are too close to the cleaning surface For Rinsing I Slide the nozzle backward to high pressure press the trigger and wait for the detergent to clear www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 MAINTENANCE SPECIFICATIONS Outlet Pressure 2500 psi Flow Rate 2 4 gallons per minute gpm Detergent Use detergent approved for pressure washers Water Supply Not to Exceed 100 F Temperature Automatic Cool Down System Will cycle when water reaches 125 155 F Shipping Weight 54 lbs GENERAL MAINTENANCE RECOMMENDATIONS The pressure washer warranty does not cover items that have been subjected to operator abuse or neglig
48. lta presi n pueden desarrollar fugas debido al desgaste dobleces o abuso Revise la manguera antes de cada uso Revise si existen cortes fugas abrasiones levantamiento de la cubierta da o o movimiento de los acoplamientos Si existe cualquiera de estas condiciones remplace la manguera inmediatamente ADVERTENCIA NUNCA repare la manguera de alta presi n Remplacela con una manguera que cumpla con la capacidad m nima de presi n de su m quina lavadora a presi n Chequee el Tubo de Sif n del Detergente Examine el filtro en el tubo del detergente y limpielo si se encuentra sucio El tubo deber a quedar apretado en la pieza Examine el tubo para ver si existe cualquier tipo de goteo o est roto Reemplace el filtro o el tubo si alguno de ellos se encuentra da ado Revise la Pistola y la Extensi n para Boquillas Examine la conexi n de la manguera a la pistola y cerciorese de que est en buen estado Pruebe el gatillo oprimi ndolo y asegur ndose de que se devuelve a su sitio cuando lo suelte Coloque el cerrojo de seguridad y pruebe el gatillo Usted no debe ser capaz de oprimir el gatillo Remplace la pistola inmediatamente si falla cualquiera de estas pruebas Elimine el Aire y los Contaminantes de la Bomba Para retirar el aire de la bomba siga los siguientes pasos l Instale la m quina lavadora a presi n como est descrito en Preparando El Lavador A Alta Presi n Para Su Uso Conecte el abastecimiento
49. ng from rear of unit Hold the hook in place with a pliers and attach the locknut with a 7 16 wrench Figure 3 Hose Hook T o E A po 4 Insert the other L hook through the hole just above the billboard on the right side of the handle viewing from rear of unit Hold the hook in place with a pliers and attach the locknut with a 7 16 wrench Figure 3 www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Speed Clean 2500 PSI Pressure Washer Briggs Stratton POWER PRODUCTS Add Engine Oil 1 Uncoil the high pressure hose and attach one end of Se a ir fein ene ee the hose to the base of the spray gun Figure 5 IMPORTANT Any attempt to crank or start the engine Tighten by hand before it has been properly serviced with the recommended oil may result in an engine failure Figure 5 Connect High Pressure Hose to Spray Gun e Place pressure washer on a level surface e Refer to engine owners manual to add recommended oil to engine Connect high pressure hose NOTE Check Oil Often During Engine Break in here Add Fuel 1 WARNING NEVER fill fuel tank indoors NEVER fill fuel tank when engine is running or hot Allow unit to cool for two minutes before refueling DO NOT light a cigarette or smoke when filling the fuel tank 2 Attach the other end of the high pressure hose to the high pressure outlet on the pump
50. nga del jard n 2 Revise que la manguera de alta presi n se encuentre conectada firmemente a la pistola de rociado y a la bomba Vea Preparando El Lavador A Alta Presi n Para Su Uso 3 Aseg rese que la unidad est nivelada 4 Conecte la manguera de jard n a la entrada del agua Aprietela con la mano Abra el suministro de agua PRECAUCI N No haga funcionar la bomba si no tiene el suministro conectado y abierto Deber cumplir con esta precauci n de otra forma la bomba resultar da ada 5 Conecte la extensi n de la lanza a la pistola rociadora Apri tela con las manos Figura 22 Figura 22 Conecte la Extensi n de la Lanza a la Pistola Rociadora Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 OPERACION Y N nA 6 Apriete el gatillo en la pistola rociadora aseg rese de que la lanza se encuentra en el modo de baja presi n para deshacerse de la presi n del aire causada al prender el agua El agua se descargara de la pistola del spray en un chorro muy Delgado Aguante el gatillo hasta que un chorro continuo de agua aparece Esto har que el comienzo del motor se haga f cilmente Suelte el gatillo 7 Coloque el pasador de seguridad al gatillo de la pistola rociadora Figura 23 Figura 23 La Pistola Rociadora con el Pasador de Seguridad en su Posici n El Pasador de la Seguridad 8 Pour d marrer le moteur suivez les instructions qu
51. nzar o pasar los 150 F 65 C incluyendo el vidrio SA Quemaduras severas pueden ocurrir al hacer contacto e NO apunte la pistola de rociado al vidrio cuando est en el modo de NO toque las superficies calientes rociado a chorro e Permita que el equipo se enfr e antes de tocarlo NUNCA apunte la pistola a plantas www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Lavadora de Presi n 2500 PSI de Speed Clean Briggs Stratton POWER PRODUCTS CONOZCA SU MANQUINA LAVADORA DE ALTA PRESION CONOZCA SU MAQUINA LAVADORA DE PRESION Lea el manual del propietario y las reglas de seguridad antes de poner en marcha su m quina lavadora a presi n Compare las ilustraciones con su m quina lavadora a presi n para familiarizarse con las ubicaciones de los diferentes controles y ajustes Guarde este manual para referencias futuras Tapa del Combustible Manguera de Alta Presi n Toma de Alta Presi n Entrada de Agua Etiqueta de Datos Arrancador de Retroceso Usado para arrancar el motor manualmente Autom tico se Enfr a Sistema Los ciclos regan por bomba cuando agua alcanza 25 155 F Entibiar agua descargar de la bomba en el suelo Este sistema previene el da o interno de bomba Bomba Desarrolla alta presi n de agua Boquilla Ajustable Ajusta la presi n a alta o baja presi n rociado a chorro o en abanico
52. o central Cambie el aceite como se indica a continuaci n 1 Vac e el aceite del motor y el combustible de la limpiadora a presi n 2 Use una 8mm llave allen para extraer el tap n negro de aceite de la bomba que hay entre la salida de presi n y la entrada de la manguera de riego Figura 28 Figura 28 Cambio del Aceite de la Bomba 3 Incline la limpiadora a presi n hacia un lado para que vaciar completamente la bomba de aceite y vierta este en un recipiente homologado 4 Incline la limpiadora a presi n hacia el lado contrario y llene la bomba con el aceite recomendado a trav s del mismo orificio puede utilizar para ello un embudo peque o 5 Instale el tap n negro de aceite de la bomba y apri telo firmemente 6 Coloque la limpiadora de presi n en su posici n normal de pie A ada combustible y aceite de motor MANTENIMIENTO DEL MOTOR Consulte el manual del propietario del motor para las instrucciones de c mo mantener adecuadamente el motor PRECAUCI N Evite el contacto prolongado o repetido de piel con aceite usado de motor El aceite usado del motor ha sido mostrado al cancer de la piel de la causa en ciertos animales del laboratorio Completamente lavado expuso reas con el jab n y el agua MANTENGA FUERA DE ALCANCE DE NI OS NO CONTAMINE CONSERVE los RECURSOS VUELVA ACEITE USADO A la COLECCION CENTRA Lavadora de Presi n 2500 PSI de Speed Clean Briggs amp Stratton POW
53. o volumen de agua 2 La entrada de agua est bloqueada 3 Suministro de agua inadecuado 4 La manguera de entrada est doblada o presenta fugas 5 El colador de la manguera de entrada est tapado 6 El suministro de agua est por encima de los 100 F 7 La manguera de alta presi n est bloqueada o presenta fugas 8 La pistola presenta fugas 9 La boquilla est obstruida 10 Bomba defectuosa 2 Limpie la entrada Proporcione flujo de agua adecuado 4 Estire la manguera de entrada coloque un parche en la fuga 5 Revise y limpie el colador de la manguera de entrada pl 6 Proporcione suministro de agua m s fr a 7 Retire las obstrucciones de la manguera de salida 8 Remplace la pistola 9 Limpie la boquilla 10 P ngase en contacto con el centro de servicio Briggs and Stratton El detergente no se mezcla con el rociado El tubo de succi n de detergente no est sumergido 2 El filtro de qu micos est tapado pa Sucio en el filtro de la l nea 4 La boquilla est en el modo de alta presi n Coloque el tubo de succi n de detergente en el detergente 2 Limpie o remplace el filtro tubo de succi n de detergente Vea Cheque En el Filtro de la L nea en la p gina 28 4 Mueva la boquilla hacia adelante para el modo de baja presi n w El lavadora de presi n se apaga durante la operaci n Sin gasolina 30 Llene el tanque de combust
54. re Washer Briggs Stratton POWER PRODUCTS PREPARING THE UNIT FOR STORAGE Water should not remain in the unit for long periods of time Sediments or minerals can deposit on pump parts and freeze pump action If you do not plan to use the pressure washer for more than 30 days follow this procedure Flush chemical injection hose by placing the filter into a pail of clean water while running pressure washer in low pressure mode adjustable nozzle in the forward position Flush for one to two minutes 2 Shut off the engine and let it cool then remove high pressure and garden hoses Disconnect spark plug wire from spark plug 3 Empty the pump of all pumped liquids by pulling the recoil handle about 6 times This should remove most of the liquid in the pump 4 Use PumpSaver to prevent corrosion build up and freezing of pump 5 Store unit in a clean dry area MAINTENANCE Protecting the Pump To protect the pump from damage caused by mineral deposits or freezing use PumpSaver to treat pump This prevents freeze damage and lubricates pistons and seals NOTE PumpSaver is available as an optional accessory lt is not included with the pressure washer Contact the nearest authorized service center to purchase PumpSaver CAUTION You must protect your unit from freezing temperatures Failure to do so will permanently damage your pump and render your unit inoperable Freeze damage is not cov
55. re washer as described in Preparing Pressure Washer For Use Connect the water supply and turn water on Remove the nozzle extension from the spray gun Start the engine according to instructions in How To Use Your Pressure Washer Squeeze the trigger on the spray gun and hold 5 When the water supply is steady and constant engage the safety latch and refasten the nozzle extension Check In Line Filter Refer to Figure 13 and service the in line filter if it becomes clogged as follows Figure 13 Clean In Line Filter Nozzle Extension I Detach spray gun and nozzle extension from high pressure hose Detach nozzle extension from spray gun and remove o ring and screen from nozzle extension Flush the screen spray gun and adjustable nozzle extension with clean water to clear debris 2 If the screen is damaged the o ring kit contains a replacement in line filter screen and an o ring If undamaged reuse screen 3 Place the in line filter screen into the threaded end of the nozzle extension Direction does not matter Push the screen in with the eraser end of a pencil until it rests flat at the bottom of the opening Take care to not bend the screen 4 Place the o ring into the recess Push the o ring snugly against the in line filter screen 5 Assemble the nozzle extension to the spray gun as described earlier in this manual Nozzle Maintenance A pulsing sensation felt while squeezing the spr
56. res de fugas las conexiones de las mangueras y la pistola ellos pueden desgastarse o da arse con el uso Su m quina lavadora a presi n viene con un Juego de Mantenimiento para anillos O el cual contiene anillos o arandela de caucho y un colador de repuesto para la entrada de la manguera de jard n La nota que no todas las partes en el juego se usar n en su unidad Para retirar un anillo O desgastado o da ado e Utilice un destornillador de cabeza plana peque o col quelo por debajo del anillo o y s quelo haciendo palanca Limpiando el Tubo Si usted us el tubo usted debe lavarlo con agua limpia antes de parar el motor Coloque el filtro y la inyecci n qu mica en un balde lleno de agua limpia 2 Deslice boquilla ajustable hacia adelante al modo bajo de la presi n Lave de a 2 minutos 3 Apague el motor IMPORTANTE Apagando el motor simplemente no soltar la presi n en el sistema Cuando el motor se ha apagado apriete el gatillo en la pistola rociadora para deshacerse de la presi n en la manguera www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Mantenimiento de la Bomba Cambio del aceite de la bomba Cambie el aceite cada 50 horas o una vez al a o lo que suceda antes NOTA Debe adquirir una botella de aceite para la bomba previamente medido N de pieza 190585GS avisando el m s cercano servicio autorizad
57. rgente se seque la superficie podr a quedar con manchas IMPORTANTE Usted deber lavar el sistema de inyecci n de qu micos despu s de cada uso colocando el filtro en un balde de agua limpia y haciendo funcionar la m quina lavadora a presi n de a 2 minutos en el modo de baja presi n Enjuage de la M quina Lavadora a Presi n ADVERTENCIA Sea extremadamente cuidadoso si usa la m quina lavadora a presi n desde una escalera andamio o cualquier superficie relativamente inestable Cuando oprima el gatillo la fuerza de reacci n del rociado inicial podr a hacerlo caer El rociado de la alta presi n podr a hacerlo caer si est muy cerca de la superficie de limpieza 26 Para Enjuage Deslice la boquilla hacia atr s a la presi n alta y apriete el disparador Llevar un pocos segundos para el detergente a claro PRECAUCI N Sujete la pistola de la hidrolavadora firmemente con ambas manos cuando utilice el rociado a alta presi n De esta manera evitar lesiones producidas por el posible golpe de la pistola hacia atr s NOTA Tambi n puede detener la circulaci n del detergente retirando el tubo de succi n del recipiente 2 Mantenga la pistola de rociado a una distancia segura del rea que planea rociar 3 Aplique un rociado de alta presi n en un rea peque a despu s revise si la superficie presenta da os Si no encuentra da os puede continuar con el trabajo de limpieza Comience en la p
58. se Replace it A WARNING Running engines produce heat Temperature of muffler and nearby areas can reach or exceed 150 F 65 C ES DA Severe burns can occur on contact e DO NOT touch hot surfaces e Allow equipment to cool before touching Briggs amp Stratton POWER PRODUCTS A WARNING Starter and other rotating parts can entangle hands hair clothing or accessories DO NOT wear loose clothing jewelry or anything that may be caught in the starter or other rotating parts e Tie up long hair and remove jewelry A WARNING High pressure spray can cause paint chips or other particles to become airborne e Always wear eye protection when you use this equipment or when you are in the vicinity where the equipment is in use A WARNING electric shock y 4 Unintentional sparking can result in fire or WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE WASHER e Disconnect the spark plug wire from the spark plug and place the wire where it cannot contact spark plug Excessively high or low operating speeds increase risk of injury and damage to pressure washer DO NOT tamper with governed speed DO NOT operate the pressure washer above the rated pressure CAUTION High pressure spray may damage fragile items including glass DO NOT point spray gun at glass when in the jet spray mode NEVER aim the spray gun at plants www mymowerparts com Speed Clean 2500 PSI Pressure Was
59. st da ada limpiela si se encuentra sucia _ 4 Haga correr el agua a trav s de la manguera de su jardin por 30 segundos para limpiar cualquier escombro que se encuentre en ella Corte el agua IMPORTANTE Hace no agua de parar de siphon para el abastecimiento de agua Use agua SOLO fr a menos que 00 F 5 Conecte la manguera de jard n no exceder 50 pies en la longitud a la entrada del agua Apriete con la mano Figura 21 PRECAUCI N DEBE haber por lo menos diez pies de manguera de jard n libre entre la entrada de agua de la lavadora a presi n y cualquier dispositivo de control de flujo de agua sea el caso de un conector Y o de cualquier otro tipo de v lvula El da o a la lavadora a presi n resultado de la desatenci n a esta precauci n no ser cubierto por la garant a 23 Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Lavadora de Presi n 2500 PSI de Speed Clean Briggs amp Stratton POWER PRODUCTS 6 ABRA el suministo del agua y abra la valvula de suministro para purgar la sistema de bomba de aire y impureza PRECAUCION Antes de darle arranque a la m quina lavadora a presi n aseg rese de usar protecci n adecuada para los ojos LISTA DE REVISION PREVIA AL ARRANQUE DEL MOTOR Revise la unidad para asegurarse que ha llevado a cabo los siguientes procedimientos Cerci rese el manecilla es seguro 2 Revise que haya sido
60. stallation or alteration and modification misuse negligence accident overloading overspeeding improper maintenance repair or storage so as in our judgment to adversely affect its performance and reliability This warranty also does not cover normal maintenance such as adjustments fuel system cleaning and obstruction due to chemical dirt carbon lime etc e Other Exclusions Also excluded from this warranty are wear items such as quick couplers oil gauges belts o rings filters pump packing etc pumps which have been run without water supplied or damage or malfunctions resulting from accidents abuse modifications alterations or improper servicing or freezing or chemical deterioration Accessory parts such as guns hoses wands and nozzles are excluded from the product warranty Also excluded is used reconditioned and demonstration equipment equipment used for prime power in place of utility power and equipment used in life support applications BRIGGS amp STRATTON POWER PRODUCTS GROUP LLC JEFFERSON WISCONSIN U S A www mymowerparts com
61. ter less than 100 F 4 Run water through your garden hose for 30 seconds to clean out any debris Make sure the handle is in place and secure 2 Check that oil has been added to the proper level in 5 Connect the garden hose not to exceed 50 feet in the engine crankcase length to the water inlet Tighten by hand Figure 7 dd Gie proper secalnees tual ank CAUTION There MUST be at least ten feet of 4 Check for properly tightened hose connections unrestricted garden hose between the pressure washer inlet and any flow shut off device such as a Y shut off connector or other convenience type water shut off valve Damage to pressure washer resulting from disregarding this warning will not be covered by the warranty 7 Be sure to read Safety Rules and How To Use Your Pressure Washer before using the pressure washer Check to make sure that there are no kinks cuts or damage to the high pressure hose 6 Provide a proper water supply at an adequate flow www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 Speed Clean 2500 PSI Pressure Washer Briggs Stratton POWER PRODUCTS HOW TO USE YOUR PRESSURE WASHER If you have any problems operating your pressure washer please call the pressure washer helpline at 1 800 743 4115 How to Start Your Pressure Washer To start your pressure washer for the first time follow these ins
62. tructions step by step This starting information also applies if you have let the pressure washer sit idle for at least a day Place the pressure washer near an outside water source capable of supplying water at a flow rate greater than 3 4 gallons per minute and no less than 20 PSI at the pressure washer end of the garden hose 2 Check that the high pressure hose is tightly connected to the spray gun and to the pump See Preparing Pressure Washer for Use for illustrations Make sure unit is in a level position 4 Connect the garden hose to the water inlet on the pressure washer pump Turn ON the water CAUTION DO NOT run the pump without the water supply connected and turned on You must follow this caution or the pump will be damaged 5 Attach the adjustable nozzle extension to the spray gun Figure 8 Tighten by hand Figure 8 Connect Nozzle Extension to Spray Gun 6 Position the nozzle in the low pressure mode see How to Use the Adjustable Nozzle and squeeze the trigger on the spray gun to relieve the air pressure caused by turning ON the water Water will flow out of the spray gun in a thin stream Continue to hold trigger until there is a steady stream of water and no air remains in the system This will make it easier to pull start the engine Release the trigger 7 Engage the safety latch to the spray gun trigger Figure 9 Figure 9 Spray Gun with Safety Latch Engaged RN 8
63. with regular unleaded fuel here Always leave room for fuel expansion High Pressure Hose Connect one end to water pump and the other end to spray gun High Pressure Outlet Connection for high pressure hose Oil Fill Dipstick Check and fill with oil here Pump Develops high pressure Recoil Starter Used for starting the engine manually Spray Gun Controls the application of water onto cleaning surface with trigger device Includes safety latch Throttle Control Lever Sets engine in starting mode for recoil starter and stops a running engine Water Inlet Connection for garden hose www mymowerparts com Briggs amp Stratton Generac Generator Discount Parts Call 606 678 9623 or 606 561 4983 IMPORTANT Read entire owner s manual before you attempt to assemble or operate your new pressure washer REMOVE PRESSURE WASHER FROM CARTON Remove the parts bag accessories and inserts included with pressure washer 2 Slice two corners at the end of carton from top to bottom so the panel can be folded down flat 3 Remove pressure washer from carton Carton Contents Items in the carton include e Main Unit e Handle e High Pressure Hose Spray Gun e Nozzle Extension Safety Goggles e Oil Bottle e Parts Bag which includes the following Owner s Manual Engine Manual e Owner s Registration Card Handle Attachment Hardware PREPARING PRESSURE WASHER FOR U

Download Pdf Manuals

image

Related Search

Related Contents

RCA P46920BL User's Manual  Snapper SST-16CL User's Manual  Philips HD2393  1. INTRODUZIONE - Brevini Power Transmission  FC7000-75/100/130/160      User manual M1  Kenmore Elite 30'' Gas Cooktop 3230 Installation Guide    

Copyright © All rights reserved.
Failed to retrieve file