Home

Manual de instrucciones bilingüe (Español e Inglés)

image

Contents

1. Figure 32 Window extensi n 4 24 Data transmission to the PC The oscilloscope OS 782 has an USB port that allows to transmit the data shown and or memorized from the instrument to the computer With the equipment a CD with the communication program is enclosed In order to install it you must follow these instructions 1 Insert the CD in the disc drive Page 47 02 2010 users manuan osz APRAX 02 2010 Open the explorer and run the Setup exe file and follow the installer instructions By default the program is installed in folder c Program files PROMAX OS wave Once installed connect the USB cable between the equipment and the PC Power on the instrument the PC will automatically detect a new equipment and request about installing the suitable driver Select the advanced method of installation and in the following screen select the folder USBDRIVE which there is within the directory where the program has been installed Press Next to install the driver Now you can open the HDSO Wave program to capture data using the PC Page 48 users manuan oszse Oo o 5 USING THE MULTIMETER 5 1 About this chapter This chapter provides a step by step introduction to the multi meter functions of the test tool hereafter The introduction gives basic examples to show how to use the menus and perform basic operations 5 2 Making Meter Connections Use the three 4 mm safety banana
2. Duty DelayA pf DelayA Bt To measure the frequency of CH1 with Measurement 1 and the peak to peak of CH2 with Measurement 2 do the following 1 Press the MENU key and the function menu is shown at the right of the screen 2 Press the MENU A or MENU V key to select Measurement 1 Five options appear at the bottom of the screen 3 Press the F1 key to select the frequency measurement as CH1 The measurement window 1 on the screen turns into one red in color and shows the frequency of CH1 4 Press the MENU A or MENU V key to select Measurement 2 Five options appear at the bottom of the screen 5 Press the F4 key to jump to the peak to peak measurement as CH2 The measurement window on the screen turns into one blue in color and shows the peak to peak value of CH2 02 2010 Page 38 users manuan oszse Now you can see a screen that looks like the following figure Figure 23 Automatic Measurements Term interpretation Vpp Vmax Vmin Vamp Vtop Vbase Overshoot Preshoot Average Vrms Rise Time Fall Time Page 39 Peak to Peak Voltage The maximum amplitude The most positive peak voltage measured over the entire waveform The minimum amplitude The most negative peak voltage measured over the entire waveform Voltage between Vtop and Vbase of a waveform Voltage of the waveform s flat top useful for square pulse waveforms
3. To next menu The Video triggering menu Second page 1 When the sync is Line Field Odd Field Even Field the second page menu is shown as below NTSC Video format setting PAL SECAM Holdoff To go to holdoff menu 2 2 Back to previous menu gt Page 31 02 2010 users manuan oszee O 2 When the sync is Designed Line the second page menu is shown as below NTSC Format PAL SECAM Video format setting Line Increase Set the line value to increase Decrease Set the line value to decrease Line No Set and Show the line valve Holdoff To go to holdoff menu 2 2 Back to previous menu gt When you go to the holdoff menu you can see a screen in the following figure 19 Figure19 Trigger Holdoff The Holdoff menu is described in the following table Function menu Settings Description Off Time Set time slot before another trigger event Increase Set the off time to increase Time Decrease Set the off time to decrease Reset Reset Holdoff time to 100ns Off Time Back Back to previous menu 02 2010 Page 32 users manua ose APRAX NOTE Trigger Holdoff can stabilize complex waveform such as the pulse range Holdoff time is the oscilloscope s waiting period before starting a new trigger During Holdoff oscilloscope will not trigger until Holdoff ends 4 15 Acquiring Mode Setting Open the vertical menu of functions and s
4. Manual control of the measurement range Measurement analogue range Test lead indicates the scale of test reading different test modes display different colors Page 50 users manuan osz APRAX 5 4 Making Multimeter Measurements Press DMM OSC key the oscilloscope will switch to the multimeter measure the screen will display the multimeter windows at the same time prompt to correctly insert testing pen of the multimeter at this time then press any key to enter into multimeter measure 5 4 1 Measuring Resistance Values To measure a resistance do the following 1 Press the R key and R appears at the top of the screen 2 Insert the black lead into the COM banana jack input and the red lead into the V Q banana jack input 3 Connect the red and black test leads to the resistor The resistor value readings are shown on the screen in Ohm Now you can see a screen that looks like the following figure 34 Figure 34 Measure resistance 5 4 2 Making a Diode Measurement To make a measurement on the diode do the following 1 Press the R key and R appears at the top of the screen 2 Press AUTO SET key once and the following is displayed on the screen dh mE Page 51 02 2010 users manuan oszee 3 Insert the black lead into the COM banana jack input and the red lead into the V Q banana jack input 4 Connect the red and black leads to the resistor and the diode resistor rea
5. para ajustar la posici n Cero del Canal 1 en la direcci n vertical y OSC 4 o OSC DB para ajustar la posici n horizontal Pulse OSC OPTION de nuevo El siguiente texto aparecer en la esquina inferior izquierda de la pantalla como se muestra en la figura 7 P gina 16 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 lt gt Tiempo A CH2 Cero f 1 117 2 Up 160 Figura 7 Posici n de punto cero del Canal 2 8 Pulse las teclas OSC A o OSC Y para ajustar la posici n Cero del Canal 2 la direcci n vertical y OSC 4 o OSC gt para ajustar la posici n horizontal 9 Pulse OSC OPTION de nuevo El siguiente texto aparecer en la esquina inferior izquierda de la pantalla como se muestra en la figura 8 lt gt Tiempo A Y Trigger f 1 130KHZ Up 144 0mu LEFT RIGHT Tine ae Figura 8 Posici n del nivel de disparo P gina 17 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX 10 Pulse las teclas OSC A o OSC Y para ajustar la posici n de disparo del Canal 2 y OSC 4 o OSC gt para ajustar la posici n horizontal 11 Pulse OSC OPTION de nuevo para volver al punto 1 4 6 Reiniciar el osciloscopio Si usted quiere reiniciar el osciloscopio y recuperar las configuraciones de f brica haga lo siguiente 1 Pulse la tecla MENU y el menu de funciones aparecer a la derecha de la pantalla 2 Pulse las t
6. 2 2 Ejemplos Descriptivos de las Categor as de Sobretensi n Cat Instalaciones de baja tensi n separadas de la red Cat Il Instalaciones dom sticas m viles Cat III Instalaciones dom sticas fijas Cat IV Instalaciones industriales 02 2010 Pagina 8 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 3 DESCRIPCI N DE MANDOS Y ELEMENTOS En la Figura 1 se pueden observar los distintos controles del equipo Figura 1 Panel frontal del equipo Descripci n 1 Conector alimentaci n DC Puerto USB Interruptor encendido apagado de la retroiluminaci n D POWER Tecla de encendido apagado A Tecla de medida de corriente V Tecla de medida de voltaje P gina 9 022010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX 11 12 13 14 15 16 17 18 19 20 21 22 02 2010 R Tecla de medida de resistencia diodo continuidad y capacitancia OSC lt Tecla de cursor izquierda del osciloscopio OSC P Tecla de cursor derecha del osciloscopio OSC OPTION Tecla de ajuste de osciloscopio Combinando las cuatro teclas OSC lt OSC gt OSC A y OSC Y se pueden hacer las configuraciones siguientes pulsando OSC OPTION Las configuraciones incluyen escala vertical del Canal 1 CH1 VOL y Canal 2 CH2 VOL Base de tiempos primaria TIME BASE punto cero del Canal 1 CH1 ZERO punto cero del Canal 2 CH2 ZERO posici n horizontal de disparo TIME y posici n
7. Voltage of the waveform s flat base useful for square pulse waveforms Defined as Vmax Vtop Vamp useful for square and pulse waveforms Defined as Vmin Vbase Vamp useful for square and pulse waveforms The arithmetic mean over the entire waveform The true Root Mean Square voltage over the entire waveform Time that the leading edge of the first pulse in the waveform takes to rise from 10 to 90 of its amplitude Time that the falling edge of the first pulse in the waveform takes to fall from 90 to 10 of its amplitude 02 2010 users manua osz LAR PROMAXX Width The width of the first positive pulse in 50 amplitude points Width The width of the first negative pulse in the 50 amplitude points Delay 1 2 The delay between the two channels at the rising edge Delay 1 2 t The delay between the two channels at the falling edge Duty Duty Cycle defined as Width Period Duty Duty Cycle defined as Width Period 4 20 Setting the Cursor Measurements This oscilloscope allows you to make manual cursor measurements on time and voltage The signal sources include Channel 1 CH1 and Channel 2 CH2 The cursor measurement menus are listed and described in the following table mum CC CTN Close Close the cursor measurement Voltage Display the voltage measurement cursor and menu Display the time measurement cursor and menu Time Signal CH1 Select the waveform channel on which the cursor s
8. ll Rango Precisi n Resoluci n 40 00 mA 1 5 3 d gitos 10 pA 400 0 mA 2 1 d gito 100 pA 20A 5 3 digitos 10 mA Resistencia Rango Precisi n Resoluci n 400 0 1 3 d gitos 4 000k 40 00k Q 400 0k Q 4 000M Q 40 00M Q 1 1 d gito 1 5 3 digitos Capacitancia Rango Precisi n Resoluci n 51 20 nF 512 0 nF 5 120 uF 3 d gitos 51 20 uF Diodo Voltaje OV 1 5V Prueba de continuidad Se puede oir un pitido cuando la resistencia es menor de 50 Q 1 ATENCI N No superar en ning n caso 400mA o 20 A respectivamente 2 Con el m dulo de extensi n de medida de corriente 02 2010 P gina 6 2 2 1 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 PRESCRIPCIONES DE SEGURIDAD AN Generales Utilizar el equipo como OSCILOSCOPIO solamente en sistemas con el negativo de medida conectado a tensiones no peligrosas respecto al potencial de tierra Utilizar el equipo como MULTIMETRO solamente en puntos con un potencial m ximo de 400V respecto al potencial de tierra y categor a de Sobretensi n CAT Il Este equipo puede ser utilizado en instalaciones con Categor a de Sobretensi n II y ambientes con Grado de Poluci n 2 El adaptador de red puede ser utilizado solamente en interiores Al emplear cualquiera de los siguientes accesorios debe hacerse s lo con los tipos es
9. The function setting menu is described in the following list 02 2010 Page 36 users manuan osz APRAX Function menu Setting Description Recall Factory Resume the instrument to its factory settings Auto Calibration Perform the self correcting procedure Language SPANISH Select the display language of the system ENGLISH Self correcting The self correcting program can improve the accuracy of the oscilloscope under the ambient temperature to the maximum If the ambient temperature variation is equal to or larger than 5 Celsius degrees the self correcting program should be performed to gain the maximum accuracy Before the self correcting program is performed the probe or lead should be disconnected with the input connector then select the F2 key Self correcting item After confirming that everything is ready press the F2 key Self correcting key and enter into the self correcting program 4 19 Making Automatic Measurements The oscilloscope can perform 20 types automatic measurements such as frequency cycle average value peak to peak value root mean square value Vmax Vmin Vtop Vbase Vamp Overshoot Preshoot RiseTime Fall Time Width Width Duty Duty Delay A B and Delay A B Y And gives two kinds of measurement results simultaneously on the screen The function menu for automatic measurements is described in the following list Function menu Settings Description Measur
10. adaptador para peque a capacitancia de este mult metro y el modo de medida de valor relativo para mejorar la precisi n de medici n Esta operaci n tardar aproximadamente 30 segundos si la medida de capacitancia es mayor de 40uF Ver Figura 37 Figura 37 Medida de capacitancia P gina 51 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX 5 4 5 Medici n de voltaje en Corriente Continua Voc Para medir un voltaje en DC haga lo siguiente Pulse la tecla V y el s mbolo DCV aparecer en la parte superior de la pantalla Inserte el cable negro en la entrada COM tipo banana y el cable rojo en el la entrada V tipo banana Conecte el otro extremo de los cables rojo y negro al punto que desea medir El voltaje entre los puntos medidos se mostrar en pantalla Ver Figura 38 Figura 38 Medida de voltaje en Corriente Continua 5 4 6 Medici n de voltaje en Corriente Alterna Vac Para medir el voltaje en CA haga lo siguiente 02 2010 Pulse la tecla V el simbolo DCV en la parte superior de la pantalla Pulse la tecla AUTO SET y el simbolo ACV aparecera en la zona superior de la pantalla Inserte el cable negro en la entrada COM tipo banana y el cable rojo en el la entrada V tipo banana Conecte el otro extremo de los cables rojo y negro al punto que desea medir El voltaje de CA entre los puntos medidos se mostrar en pantalla Ver Figura 3
11. 36 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 Ahora se puede ver una pantalla parecida a la siguiente figura Figura 23 Medidas autom ticas Definici n de conceptos Vamp Vtop Vbase Over shoot Pre shoot Vavg Promedio Vrms Vef Tiempo subida Tiempo de bajada Ancho P gina 37 Voltaje de Pico a Pico Amplitud m xima El voltaje de pico m s positivo medido sobre la se al entera Amplitud m nima El voltaje de pico m s negativo medido sobre la se al entera Voltaje entre Vtop y Vbase de una se al Voltaje en cumbre plana de la se al til para se ales cuadradas y pulsos Voltaje en base de la se al til para se ales cuadradas y pulsos Se define como la tensi n de pico post Flanco de subida til para se ales cuadradas y pulsos Se define como la tensi n de pico pre Flanco de subida til para se ales cuadradas y pulsos La media aritm tica de la se al completa El valor absoluto de la ra z cuadrada del voltaje de la se al Tiempo en el que el flanco de subida de la se al crece de 10 a 90 de su amplitud Tiempo en el que el flanco de bajada de la se al pasa de 90 a 10 de su amplitud El ancho del primer pulso positivo en el 50 de los puntos de amplitud 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX NOTA el manual del OD 590 hay unos dibujos que representan muy bien el significado de cada medida Ancho El ancho del prim
12. AUTO SET to enter into Autoscale DSO switches to YT mode and AUTO status 02 2010 Page 44 users manuan os7ee O At the mode of Autoscale DSO is always in the state of DC coupling and AUTO triggering In this case the forbidden information will be showing when making Triggering or Coupling settings At the mode of Autoscale if adjust the vertical position voltage division trigger level or time scale of CH1 or CH2 the oscilloscope will turn off Autoscale function and if press AUTOSET again the oscilloscope will enter into Autoscale Turn off the submenu at the Autoscale menu the Autoscale is off and turn on the submenu still enters into the function When video triggering the horizontal time scale is 50us If one channel is showing edge signal the other channel is showing video one the time scale refers to 50us as video one as standard 4 22 System State Menu The system state menu is used to display information about the present horizontal system vertical system trigger system and others The operation steps are shown as below 1 Page 45 Press the MENU key and the function menu is displayed at the right of the screen Press the MENU A or MENU Y key to select the System State Four options appear at the bottom of the screen Sequentially press key F1 through F4 key and the corresponding state information will be shown on the screen The screen that looks like the following figure 30 wi
13. Digital Storage OS 782 1 GENERAL 1 1 Description The OS 782 poliscope has two measurement instruments built in one digital oscilloscope and one multimeter Its rugged construction small size lightweight and battery powered lead it to be a handheld instrument ideal to carry out multiple external measurements where to work with conventional equipments it is very uncomfortable It is very useful to measure the electrical magnitudes and to repair electronic equipments given its large diversity of functions which causes that it become an useful tool in laboratories as well as for R amp D and training activities The measurement carried out by the equipment appears on a hi resolution LCD with backlight Their basic characteristics in each one of their operating modes are e Two channels oscilloscope with bandwidth of 20 MHz e Sampling rate of 100 MS s e Trigger TV and edge e 20 automatic measurements modes e Auto scale function e Memory depth of 6k points by channel e USB port e Digital Multimeter of 3 34 for measurements of R V A and C e AC adapter and Ll ion battery Display LCD colour of 3 8 with backlight 320x240 pixels e Vertical and horizontal cursors Page 1 02 2010 USER S MANUAL OS 782 AXPROMAX 1 2 Specifications Oscilloscope A Only if another instructions are provided are all technical specifications applicable to the probe with the 10X attenuation switch setting and the HDS seri
14. OFF Turn off Autoscale ON Turn on Autoscale Mode Vertical Follow up and adjust vertical scale without changing horizontal setting Follow up and adjust horizontal scale without Horizontal changing vertical setting Follow up and adjust the vertical and horizontal settings HORI VERT Only show one or two periods Show Multi period waveforms 02 2010 Page 42 users manuan oszee LAR PROIMIAXY If you want to measure voltage of Channel 1 you can do as the follows 1 Press MENU the function menu will appear on the right of the screen 2 Press MENU or MENU Y and choose Autoscale three options will show at the bottom of the screen 3 Press F1 and choose ON 4 Press F2 and choose Hori Vert 5 Press F3 and T Figure 27 Autoscale Horizontal Vertical mono period waveform Page 43 02 2010 users manuan os7ee O oO o T 1 000ms Figure 28 Only under vertical mode multi period waveform Figure 29 Only under horizontal mode multi period waveform NOTE 1 Entering into Autoscale function and Aa flicker will be on the top left corner flicker every 0 5 second 2 At the mode of Autoscale the oscilloscope can self estimate Trigger mode Edge Video and Alternate and Type Edge Video If now you press Trigger mode or Type the forbidden information will display on the screen 3 At the mode of XY and STOP status pressing
15. Time A V CH1 Zero f 1 117KHZ Up 144 0 Figure 6 Zero point position of channel 1 6 Press OSC A or OSC Y key to adjust the zero position of Channel 1 in vertical direction and press OSC lt or OSC gt key to adjust the horizontal position 7 Again press OSC OPTION key and the following appears at the bottom left side of the screen shown as the following figure 7 02 2010 Page 18 users manuan oszee lt gt Time A V CH2 Zero f 1 117 2 Up 160 0mu Figure 7 Zero point position of channel 2 8 Press the OSC A or OSC W key to adjust the zero position of Channel 2 in the vertical direction and press OSC 4 or OSC gt key to adjust the horizontal position 9 Press OSC OPTION key once more and the following appears at the bottom left of the screen shown as the following figure 8 lt gt Time A V Trig 1 130KHZ Up 144 0mu Figure 8 Trigger level position Page 19 02 2010 users manuan os7ee oO o 10 Press the OSC A or OSC W key to adjust the trigger position of Channel 2 and press OSC lt or OSC gt key to adjust the horizontal position 11 Press the OSC OPTION key again and return back to step 1 4 6 Resetting the Oscilloscope If you want to reset the Oscilloscope to the factory settings do the following 1 Press MENU ke
16. atenuaci n de la sonda Si la atenuaci n de la sonda tiene un factor de 10 1 la escala del canal de entrada del osciloscopio deber a ser ajustada a 10x para evitar errores en la informaci n visualizada Pulse la tecla F3 Sonda para ir a los ajustes de la sonda que se quiere configurar Factor de atenuaci n de la sonda Ajuste de men correspondiente Tabla 1 Factor de atenuaci n de la sonda y el ajuste de men correspondiente P gina 23 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX 4 11 4 Ajuste de forma de onda invertida Forma de onda invertida la se al mostrada se invierte 180 grados en relaci n al potencial de toma de tierra Pulse la tecla F4 Invertido para invertir la se al aparecer Si pulse de nuevo F4 Invertido para anular la inversi n aparecer No 4 12 Funciones matem ticas MATH La funci n MATH muestra el resultado de sumar restar multiplicar o dividir las formas de onda de los canales CH1 y CH2 El resultado de las operaciones aritm ticas tambi n se puede medir con la cuadr cula de la pantalla o con el cursor La amplitud de las formas de onda calculadas se puede ajustar con la tecla pulsando OSC OPTION y modificando el par metro CHMath Volts div que es mostrado en pantalla La amplitud se extiende de 0 001 a 10 con pasos de 1 2 5 es decir puede ser expresado como 0 001x 0 002x 0 005x 10x La posici n de la forma de onda calculada se puede ajustar ar
17. del nivel de disparo TRIG e El usuario puede tambi n ajustar la escala vertical CHM VOL la posici n horizontal CHM ZERO de la se al resultante de una operaci n matem tica En el modo de medida con cursor se pueden ajustar las posiciones del cursor 1 V1 o T1 y del cursor 2 V2 o T2 OSC V Tecla de cursor abajo del osciloscopio OSC A Tecla de cursor Arriba del osciloscopio OSC DMM Tecla de cambio de modo Osciloscopio Mult metro AUTOSET e En Modo Multimetro al medir corriente o voltaje se puede cambiar de medida de corriente alterna a corriente continua pulsando esta tecla al medir resistencia se puede seleccionar medida de resistencia diodo continuidad o capacitancia pulsando esta tecla e En Modo Osciloscopio esta tecla sirve para auto configuraci n RUN STOP Tecla para ejecutar o detener la operaci n de medida MENU WY Elige el elemento inferior en la lista del men MENU Muestra oculta el men en pantalla MENU Elige el elemento superior en la lista del men F1 F5 Permite modificar las opciones de cada men Conectores BCN de entrada de los canales del osciloscopio CH1 y CH2 Terminales de entrada del mult metro tres terminales tipo banana mA A COM V Q C y dos terminales cuadrangulares para medici n de capacitancia Salida de compensaci n de sonda Se al de test de 5 Vpp y 1 kHz de frecuencia P gina 10 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 4 UTI
18. jack inputs for the Meter functions COM V Q mA Two quadratic capacitance jacks CX See figure 1 for the connections 5 3 Multimeter Operation Window 1 2 3 4 5 MANUAL Figure 33 Page 49 02 2010 usmswwuaLosze LAR PROMAXX Description 1 2 4 5 6 7 8 9 10 11 12 02 2010 Battery electric guantity indictor MANUAL AUTO RANGE indictors among which the MANUAL means measuring range in manual operation mode and Auto refers to the measuring range in automatic operation mode Measurement mode indicators DCV Direct voltage measurement CC ACV Alternating voltage measurement CA DCA Direct current measurement CC ACA Alternating current measurement CA R Resistance measurement qh Diode measurement q C Capacitance measurement On Off measurement The relative magnitude measurement indicator Running state indicators among which RUN expresses continuous update and STOP represents the screen locking The reference value of the relative magnitude measurement The multiplying power of the dial indication To multiply the reading of dial pointer by multiplying power will get the measurement result The mail reading of measurement Automatic control measuring range Absolute relative magnitude measuring control The sign expresses the absolute magnitude measuring control and A represents the relative magnitude measuring control
19. key and DCA appears at the top of the screen The unit on the main reading screen is mA mA and 20A will display on the right bottom of screen press F4 or F5 to switch the measurement between Ma and 20A 400mA is acquiescently 2 Insert the black lead into the COM banana jack input and the red lead into the mA banana jack input 3 Connect the red and black leads to the measured points and the DC current values of measured points will be displayed on the screen Look at the display you can see a screen that looks like the following figure 40 Page 55 02 2010 users manuan os7ee LAR PROMIAXY Figure 40 DC current Measurement for 400 mA To measure a DC current which is larger than 400 mA do the following 1 Press the A key and DCA appears at the top of the screen The unit on the main reading screen is mA 2 Press F5 key change to 20 A measurement he unit on the main reading screen is A 3 Plug current extended module in current measure jack then plug the probe in the module 4 Connect the red and black leads to the measured point and the DC current value of the measured point will be displayed on the screen 5 Press F4 return to 400 mA measure Figure 41 DC current Measurement for 20A 02 2010 Page 56 users manuan oszse LAR PROIMIAXY 5 4 8 Making an AC Current Measurement In order to carry out the measurement of current it is necessary to connect in series the meter and the circuit under t
20. mode the oscilloscope cannot acquire the waveform till it is triggered When there is not any trigger the oscilloscope will display the origin waveform without new waveforms captured In this mode the oscilloscope will detect a trigger and capture a waveform at each time when the customer presses the RUN STOP key 4 14 2 Video triggering With Video triggering selected the oscilloscope performs the NTSC PAL or SECAM standard video signals field line trigger odd field even field or line num trigger Now you can see a screen that looks like the following figure 17 figure 18 f 66 67KHZ f 66 67HH2 02 2010 Figure 17 Video field trigger Page 30 users manuan os7ee LAR PROMIAXY f 666 7KHZ f 666 7 Figure 18 Video line trigger The Video triggering menu is described in the following table Function menu Polarity Normal Applicable to the video signal in which the black level is of low level Invert Applicable to the video signal of which the black level is of high level Settings Description Signal CH1 Select CH1 as the trigger source source CH2 Select CH2 as the trigger source Sync Line Make a video line trigger synchronization setting Field Make a video field trigger synchronization setting Odd Field Make a video odd field trigger synchronization setting Even field Make a video even field trigger synchronization setting Line NO Make a video designed line
21. n A se mostrar en pantalla en color verde El color de visualizaci n es verde y el punto cero de la forma de onda k el voltaje y el tiempo son de color violeta Ver Figura 22 Figura 22 Memorizaci n de formas de onda 4 18 Men de Sistema Funci n SISTEMA Abra el men vertical de funciones y seleccione la funci n SISTEMA Los par metros configurables con las teclas F1 F5 aparecer n en la parte inferior de la pantalla Los par metros de Configuraci n se describe en la siguiente tabla Par metros Configuraciones Descripci n RESET Recupera las configuraciones de f brica AUTOCALIBRAR Realiza autocalibraci n del equipo Idiomas ESPA OL Selecciona el idioma de visualizaci n del INGLES sistema 02 2010 P gina 34 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 Autocalibraci n El programa de autocalibraci n puede mejorar la exactitud del osciloscopio a temperatura ambiental al m ximo Si la variaci n de temperatura ambiente es igual o mayor de 5 C el programa de autocorrecci n se activa para lograr la m xima exactitud Antes de activar el programa de autocorrecci n hay que desconectar la sonda y los cables del conector de entrada Despu s de confirmar que todo est listo pulse la tecla F2 y seleccione Autocalibraci n para activar el programa de autocorrecci n 4 19 Medidas autom ticas Funciones MEDIDA 1 y MEDIDA 2 El osciloscopio puede realizar 20 tipos de medidas au
22. of peak to peak value Support the NTSC PAL and SECAM frequency Video triggering mode broadcasting systems of any field or line frequency Voltage difference AV and time difference AT between cursors AV Peak to peak value average value root mean square value Frequency cycle period Vmax Vmin Vtop Vbase Vamp Overshoot Preshoot RiseTime Fall Time Width Width Duty Duty Delay AB and Delay B A 02 2010 USER S MANUAL OS 782 GENERAL SPECIFICATIONS Display Display type Display resolution Power consumption Mechanical features Dimensions Weight Power supply Internal External Input Working environment Temperature Operation Power adapter Storage Temperature Humidity in operation 0 to 10 C 10 to 30 30 to 40 40 to 50 C Humidity in storage 0 to 10 C ACCESSORIES AXPROMAX 3 8 color LCD display 320 horizontal x 240 vertical pixels 4096 colors 180 W x 115 x 40 D mm 0 645 kg 7 4 V Li lon Built in Rechargeable battery Means network adapter included For Europe and other countries 100 240 VAC 50 Hz 6W 0 to 50 C 0 to 40 C 20 to 60 C no condensation 95 759 45 96 no condensation Two 1 1 10 1 passive oscilloscope probes of 1 2 meters long SA016 x1 x10 A pair of test leads of multimeter PPO13 One communication cable for USB port A measuring extension module for small current A measuring extension module for s
23. pantalla 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX 6 Pulse la tecla OSC OPTION repetidamente hasta que el mensaje A W CURSOR 2 aparezca en pantalla Pulse entonces OSC A OSC Y y ver que la l nea interrumpida T2 se desplaza a la derecha y a la izquierda mientras el valor del tiempo medido de T1 en relaci n a la posici n del punto central de la pantalla se visualiza en pantalla Tambi n se pueden ver los valores de tiempo absolutos y las frecuencias de T1 y T2 Ver Figura 25 CH2 OFF f 1 217KHZ Figura 25 Uso del cursor para una medida de tiempo 4 21 Auto Escala Esta funci n realiza un seguimiento de las se ales de forma autom tica incluso cuando las se ales cambian constantemente La funci n Auto escala permite al instrumento ajustar el modo de disparo la divisi n de voltaje y la escala de tiempo de forma autom tica seg n el tipo amplitud y frecuencia de las se ales El men es el siguiente Par metros Configuraciones Descripci n OFF Desactiva Auto escala Auto escala ON Activa Auto escala Vertical Seguimiento y ajuste de la escala vertical sin afectar al ajuste horizontal Horizontal Seguimiento y ajuste de la escala horizontal sin afectar al ajuste vertical HOR VERT Seguimiento y ajuste de la escala horizontal y vertical S lo muestra uno o dos per odos Muestra se ales multi per odo 02 2010 P gina 40 AXxPROMAX MANUAL DE INSTRUCC
24. resistance is less than 500 02 2010 Page 6 users manua osz PROMA 2 SAFETY RULES AN 2 1 General Only use this equipment as OSCILLOSCOPE systems with their negative of measurement connected to no dangerous voltages with respect to the ground potential Only use the equipment as MULTIMETER in points with a maximum potential of 400 V with respect to the ground potential and over voltage category CAT Il This equipment can be used in Overvoltage Category II installations and Pollution Degree 2 environments The adapter of net can be used only in interiors When using some of the following accessories use only the specified ones to ensure safety Power adapter Test leads Multimeter Measurement probes Oscilloscope The negative of measurement like Osciloscope is common to the negative potential of the conector of input output of information EI negative of measurement of the channels of the osciloscopio is common On having effected measurements to disconnect the cables that are not in use Revise the condition of test leads before the utilization Observe all specified ratings both of supply and measurement Remember that voltages higher than 70 V DC or 33 V AC rms are dangerous Use this instrument under the specified environmental conditions The user not authorized to carry out the following maintenance operations Any change on the equipment should be carrier out byqualified personnel Do no
25. se al de v deo 02 2010 P gina 28 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 La siguiente tabla describe los men s de disparo por video Par metros Configuraciones Descripci n Polaridad Normal Invertida Aplicable a la se al de v deo en la cual el nivel negro es el nivel bajo Aplicable a la se al de v deo en la cual el nivel negro es el nivel alto Fuente CH1 CH2 CH1 es usado como fuente de disparo CH2 es usado como fuente de disparo Sinc L nea Cuadro Odd field Even field Line NO Sincroniza el disparo en l nea de se al de v deo Sincroniza el disparo en cuadro de se al de v deo Sincroniza el disparo en cuadro impar de sefial de v deo Sincroniza el disparo en cuadro par de se al de v deo Sincroniza el disparo en la l nea seleccionada de se al de v deo Pasa al siguiente men El men de disparo por v deo segunda p gina 1 Cuando la sincronizaci n es del tipo l nea cuadro cuadro impar Odd field o cuadro par Even field la segunda p gina de men se muestra tal como sigue Formato NTSC PAL SECAM Configuraci n formato v deo Bloqueo Pasa al men de bloqueo Vuelve al men anterior gt 2 Cuando la sincronizaci n es del tipo linea seleccionada Line No la segunda p gina de men se muestra tal como sigue Formato NTSC PAL SECAM Configuraci n formato v deo L nea Incrementar
26. setting HORIZONTAL function 4 24 Data transmission to the PC sse paasta 47 ZXPROMAX User s Manual OS 782 5 USING THEIMULTIMETE Riess i 49 5 1 About this chapter 5 2 Making Meter Connections 5 3 Multimeter Operation Window sees 49 5 4 Making Multimeter Measurements 51 5 4 1 Measuring Resistance Values 51 5 4 2 Making a Diode Measurement 91 5 4 3 On Off test 52 5 4 4 Making a Capacitance Measurement 53 5 4 5 Making a DC voltage Measurement 54 5 4 6 Making a AC voltage Measurement VAC 54 5 4 7 Making a DC current Measurement AAC iii 5 4 8 Making an AC Current Measurement sse 57 5 5 Freezing the Readings eee ett a 58 5 6 Taking a relative measurement 5 7 Selecting automatic manual range adjustment 60 6 TROUBLE SHOOTING ii eicit intret pantera ka cacsaactedveate desidia ds 61 7 MAINTENANCE AND CLEANING 1 63 7 1 Basic maintenance 63 7 2 Cleaning 63 7 8 Storage Of oscilloscope sse arrancar 63 7 4 Substitution of the battery of lithium sese 63 users manua osz LAR PROMAXX Oscilloscope amp Multimeter
27. subida CH2 Medida del tiempo de subida de CH2 Tiempo CH1 Medida del tiempo de bajada de CH1 bajada CH2 Medida del tiempo de bajada de CH2 Medida de Ancho de CH1 Medida de Ancho de CH2 Medida de Ancho de CH1 Medida de Ancho de CH2 Medida del Ciclo de CH1 Medida del Ciclo de CH2 Medida de Ciclo de CH1 Medida de Ciclo de CH2 Retardo Medida Retardo de A7 B f de CH1 AB Medida Retardo de A B f de CH2 Retardo Medida Retardo de A B de CH1 A Bt Medida Retardo de A B de CH2 Vamp Overshoot Preshoot Ancho Ancho Ciclo Ciclo Para medir la frecuencia de CH1 con MEDIDA 1 y el valor de pico de CH2 con MEDIDA 2 haga lo siguiente 1 Pulse la tecla MENU el Men de Funciones aparecer a la derecha de la pantalla 2 Pulse las teclas MENU A o MENU para seleccionar MEDIDA 1 Cinco opciones aparecer n en la zona inferior de la pantalla 3 Pulse la tecla F1 para seleccionar la medida de frecuencia de CH1 La ventana de la Medida 1 en la pantalla se vuelve roja y muestra la frecuencia de CH1 4 Pulse las teclas MENU A o MENU para seleccionar MEDIDA 2 Cinco opciones aparecer n en la zona inferior de la pantalla 5 Pulse la tecla F4 para seleccionar la medida de pico a pico Vpp de CH2 La ventana de la Medida 2 en la pantalla se vuelve azul y muestra el valor de pico a pico de CH2 Ver Figura 23 02 2010 P gina
28. the battery is dead Check the battery symbol at the upper right of the screen The L1 symbol indicates that the battery has been run out of power and must be charged 3 The measurement type displays ERR when you switch to the multimeter mode Probably you do not select the measuring mode In this case push down any key of the three keys V A and R Thus the relative measuring mode will be shown on the screen If the ERR is still displayed restart the oscilloscope 4 The measured voltage amplitude value is 10 times larger or smaller than the actual one under the oscilloscope mode Check whether the channel attenuation factor matches the actual probe error ratio 5 The waveform is displayed on the screen but is not stable under the oscilloscope mode e Check whether the signal item in the trigger mode menu matches the actually used signal channel e Check on the trigger mode The edge trigger mode is applicable to the universal single and the video trigger mode applicable to the video signal Only when the proper trigger mode is applied can the waveform be in stable e Try to change the trigger coupling into the HF repression and LF repression to filter the HF or LF noise trigger by the interference Page 61 02 2010 users manuan osz APRAX 02 2010 There is no display on the screen when you push down RUN STOP key under the oscilloscope mode Check whether the trigger mode in the trigger mode menu is in normal or s
29. 0 P gina 30 AxPROMAX Par metros Configuraciones MANUAL DE INSTRUCCIONES OS 782 Descripci n Muestreo Modo de muestreo normal Detecci n de pico Se usa para descubrir problemas t cnicos y reducir los posibles errores Promedio Se usa para reducir ruidos arbitrarios Se pueden seleccionar varios factores promedios Factor promedio 4 16 64 o 128 Selecci n del factor promedio 4 16 Ajustes de pantalla Funci n DISPLAY Abra el men vertical de funciones y seleccione la funci n DISPLAY Los par metros configurables con las teclas F1 F5 aparecer en la parte inferior de la pantalla El ment de Ajustes de pantalla se describe en la siguiente tabla Par metros Configuraciones Descripci n Tipo Vectores Se rellena el espacio entre puntos de muestra adyacentes en la pantalla Se visualizan s lo los puntos de muestra Puntos Persistencia No Establece la cantidad de tiempo que cada 1s punto de muestra permanece en pantalla 2s 5s Infinito Formato YT El formato YT muestra el voltaje vertical con relaci n al tiempo escala horizontal Muestra XY el CH1 en el eje horizontal y CH2 en el eje vertical Gr fico Bitmap Mapa de Los datos transmitidos en la comunicaci n son bits mapas de bits Vectorial Los datos transmitidos en la comunicaci n son 4 16 1 Estilo de visualizaci n vectores El estilo de visualizaci n incluye visualizacione
30. 005KHZ Figura 16 Disparo por flanco 4 14 Control de disparo Existen dos tipos de disparo disponibles Por flanco y por v deo Hay distintas opciones de ajuste para cada tipo de disparo Disparo por flanco Dispara el osciloscopio cuando el flanco ascendente o de bajada de la serial de entrada cruza el nivel de disparo umbral Disparo por v deo Dispara el osciloscopio en l neas o campos de sef ales de v deo 02 2010 P gina 26 AxPROMAX 4 14 1 Disparo por Flanco MANUAL DE INSTRUCCIONES OS 782 La siguiente tabla describe men s de disparo por flanco Par metros Configuraciones Descripci n Pendiente Subida Disparo por flanco en la subida de la se al Bajada Disparo por flanco en la bajada de la se al Fuente CH1 CH1 es usado como fuente de disparo CH2 CH2 es usado como fuente de disparo 1 2 Pasa al siguiente menu Bloqueo Pasa al ment de Bloqueo Modo Auto Normal Unico La adquisici n de formas de onda es posible incluso cuando no se detectan condiciones de disparo La adquisici n de formas de onda s lo se puede efectuar cuando se detectan condiciones de disparo El muestreo se realiza cuando hay un solo disparo AC Corriente alterna DC Corriente continua Rechazo AF Supresi n de la alta frecuencia Rechazo BF Supresi n de la baja frecuencia Bloquea los componentes de la DC Pasan todos los componentes de la se al La parte de alta
31. 15 C lculos matem ticos de forma de onda 4 43 Ajuste del sistema de disparo Funci n TRIGGER El disparo determina el momento en que el osciloscopio empieza a obtener datos y a presentar una forma de onda Cuando se configura correctamente un disparo el osciloscopio convierte las presentaciones inestables o las pantallas en blanco en formas de onda correctamente representadas Comenzando la adquisici n de datos el osciloscopio recoge datos suficientes para dibujar la forma de onda a la izquierda del punto de disparo A la espera de que se den condiciones para el disparo el osciloscopio recopila datos continuamente Despu s de detectar un disparo el osciloscopio junta suficientes datos para dibujar la forma de onda a la derecha del punto de disparo P gina 25 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXAPROMAX Para ajustar el modo de disparo haga lo siguiente 1 Pulse la tecla MENU y el Men de Funciones aparecer a la derecha de la pantalla 2 Pulse las teclas MENU A o MENU V para seleccionar la funci n TRIGGER Cinco opciones aparecer n en la zona interior de la pantalla 3 Seleccione y pulse una de las teclas de F1 a F5 para realizar diferentes ajustes 4 Pulse la tecla OSC OPTION el siguiente texto en pantalla lt gt Tiempo A V Trigger 5 Pulse las teclas OSC A o OSC para ajustar la posici n del nivel de disparo Ver Figura 16 f 1 005 2 f 1
32. 9 P gina 52 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 Figura 39 Medida de voltaje en Corriente Alterna 5 4 7 Medici n de corriente en Corriente Continua Para realizar la medici n de corriente es necesario conectar en serie el medidor y el circuito bajo prueba Para realizar est operaci n es necesario desconectar el circuito antes de realizar dicha conexi n Para medir una corriente en DC menor de 400 mA haga lo siguiente 1 Pulse la tecla A y el s mbolo DCA aparecer en la parte superior de la pantalla La unidad de medida es mA Los s mbolos mA y 20A aparecer n en la parte inferior derecha de la pantalla Pulse F4 o F5 para cambiar el rango de medida de mA a 20A y viceversa 400mA esta seleccionado por defecto 2 Inserte el cable negro en la entrada COM tipo banana y el cable rojo en el la entrada mA tipo banana 3 Conecte el otro extremo de los cables rojo y negro al punto que desea medir Active el circuito bajo prueba y la corriente de DC entre los puntos medidos se mostrar en pantalla Ver Figura 40 P gina 53 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX Figura 40 Medida de corriente en Corriente Continua hasta 400 mA Para medir una corriente en DC mayor de 400 mA haga lo siguiente Pulse la tecla el simbolo DCA en la parte superior de la pantalla La unidad de medida es mA 2 Pulse F5 para cambiar el rango de medid
33. Channel 2 CH2 VOL Primary Timebase TIME BASE zero point position of channel 1 CH1 ZERO zero point position of channel 2 CH2 ZERO trigger horizontal position TIME and trigger level position TRIG The following example shows how to use OSC OPTION key to make a setting 1 Press once the OSC OPTION key the following is displayed at the bottom left side of the screen as shown in the figure below lt gt Time Base A V CH1 Vol f 1 117KHZ 160 0 E LEFT RIGHT Time Base P lt DOWN CHA Vol Figure 4 Voltage Unit Scale of Channel 1 2 Press the key OSC A or OSC to adjust the vertical scale of Channel 1 and press y DSC lt OSC gt to adjust the horizontal time scale 3 Press OSC OPTION once again the following display is visible at bottom left side of the screen as shown in the following figure lt gt Time Base A V CH2 Vol Page 17 02 2010 users manuan os7ee O Oo o f 1 130KHZ Up 160 T RIGHT Time Base Figure 5 Voltage Unit Scale of Channel 2 4 Press the OSC A or OSC W key to adjust the vertical scale of Channel 2 and press the OSC lt or OSC gt key to adjust the horizontal time scale 5 Press the OSC OPTION key one more time and the following display is visible at the bottom left side of the screen shown as the following figure lt gt
34. DC 1500 mA Bater a integrada de 7 4V De 0 a 50 C De 0 a 40 De 20 a 60 C Sin condensaci n 95 96 75 96 45 96 Sin condensaci n P gina 4 ZX amp PROMAX MANUAL DE INSTRUCCIONES OS 782 ACCESORIOS Dos sondas SA16 x1 x10 Puntas de prueba para el multimetro PP 013 Un cable de comunicaci n para puerto USB Un m dulo de extensi n de medida para corrientes elevadas Un m dulo de extensi n de medida para capacitancia peque a Un alimentador AC para Europa y otros pa ses AL 782 Un manual de usuario O MI1452 Un CD con software 1 3 Especificaciones Multimetro Tensi n m xima de los bornes de medida a tierra 400V CATII Tensi n continua VDC Impedancia de entrada 10MQ Rango Precisi n Resoluci n 1 1 d gito Protecci n de entrada 1000 VDC o pico AC Tensi n alterna VAC Impedancia de entrada 10 MQ Rango de frecuencia de 40 Hz a 400 Hz Visualizacion valor virtual de la forma de onda sinusoidal b Rango Precisi n Resoluci n 4 000 V 40 00 V 1 d gitos 10 mV 400 0 V 100 mV Protecci n de entrada 750 VDC o pico AC Pagina 5 02 2010 MANUAL DE INSTRUCCIONES OS 782 Corriente continua ADC 0 AXPROMAX Rango Precisi n Resoluci n 40 00 mA 1 x 1 d gito 10 uA 400 0 mA x 1 5 1 d gito 100uA 20A 2 3 3 d gitos 10mA Corriente alterna A AC
35. Decrementar Incrementa el valor de la l nea Decrementa el valor de la l nea L nea No Muestra y ajusta el n mero de l nea Bloqueo Pasa al men de bloqueo 2 2 gt P gina 29 Vuelve al men anterior 02 2010 MANUAL DE INSTRUCCIONES OS 782 Cuando se accede al figura 19 AXPROMAX men de bloqueo se puede ver una pantalla como la Figura 19 Bloqueo disparo El men tiempo de bloqueo se describe en la siguiente tabla Par metros Configuraciones Descripci n Tiempo de bloqueo Configura el intervalo de tiempo antes de que se produzca otro disparo Tiempo Incrementar Aumenta el intervalo de Decrementar aes Disminuye el intervalo de bloqueo Reiniciar tiempo de Reajusta el tiempo de bloqueo bloqueo a 100 ns Volver Vuelve al men anterior NOTA El bloqueo de disparo puede estabilizar se ales complejas tales como pulsos El tiempo de bloqueo es el periodo de espera del osciloscopio antes de iniciar un nuevo disparo Durante el tiempo de bloqueo el osciloscopio no disparar hasta que ste tiempo termine 4 15 Ajustes del modo de adquisici n FUNCI N ADQUIRIR Abra el men vertical de funciones y seleccione la funci n ADQUIRIR Los par metros configurables con las teclas F1 F5 aparecer en la parte inferior de la pantalla Los par metros del Modo de adquisici n se describe en la siguiente tabla 02 201
36. H1 is used as the trigger source CH2 is used as the trigger source 1 2 To next menu 2 2 Back to previous menu Bloqueo To holdoff menu Trigger mode Auto Normal Single shot Acquisition of waveforms is possible even if there is no triggering condition detected Acquisition of waveforms can only be done when the triggering condition is satisfied The sampling is performed on a waveform when one trigger is detected then stop sampling Coupling Term interpretation AC DC HF Suppression LF Suppression With this mode selected the DC component is prevented from passing though All dc components are allowed The HF part of the signal is prohibited and the HF component is allowed The LF part of the signal is prohibited and the LF component is allowed Trigger modes There are three kinds of trigger modes available for this oscilloscope that is auto normal and single shot Page 29 02 2010 USER S MANUAL OS 782 1 Automatic trigger mode AXPROMAX The oscilloscope can acquire the waveform without any triggering condition detected in this mode in which it will be triggered compulsively when waiting for a specified period of time without any triggering condition ignited When an invalid trigger is enforced the oscilloscope can not keep the waveform in phase 2 Normal trigger mode 3 Single shot mode In this
37. IONES OS 782 Si se desea medir el voltaje del CANAL 1 se han de seguir los siguientes pasos P gina 41 Pulse MENU y el men de opciones aparecer en el lado derecho de la pantalla Pulse MENU A o MENU Y y seleccione Auto escala aparecer n tres opciones en la parte inferior de la pantalla Pulse F1 y seleccione ON Pulse F2 y seleccione Hori Vert Figure 27 Auto Escale Horizontal Vertical mono per odo 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXSPROMAX T 1 000ms Figure 29 Sdlo bajo modo horizontal multi periodo NOTA 1 Al entrar en la funci n Auto escala parpadear el s mbolo 8 en la parte superior izquierda aprox cada 0 5 segundos 2 En el modo Auto escala el osciloscopio puede estimar el Modo de disparo Flanco V deo y Alternar y el Tipo Flanco V deo Si ahora se pulsa Modo Disparo o Tipo la informaci n oculta se mostrar en pantalla 3 En el modo de estado XY y STOP pulsando AUTO SET para entrar en Auto escala DSO cambia a modo YT y AUTO status 4 En el modo Auto escala DSO est siempre en el estado de acoplamiento DC y AUTO disparo En ese caso la informaci n oculta aparecer cuando se ajuste a disparo o acoplamiento 02 2010 P gina 42 ZXPROMAX MANUAL DE INSTRUCCIONES OS 782 En el modo Auto escala si se ajusta la posici n vertical la divisi n de voltaje el nivel de disparo o la escala de tiempo de CH1 o CH2 el osciloscopio
38. LIZACI N DEL OSCILOSCOPIO 4 1 Encendido del osciloscopio Conecte el osciloscopio a la corriente alterna con el adaptador AC el osciloscopio tambi n puede funcionar con la bater a de Li l n incorporada incluso sin el suministro de energ a de corriente alterna Encienda el osciloscopio presionando la tecla de encendido y apagado aly El equipo realiza entonces una autocomprobaci n Una pantalla de bienvenida y la frase Pulse cualquier tecla para continuar aparecer en pantalla cuando el sistema termine la autocomprobaci n Al pulsar cualquier tecla se entra en la funci n de medici n Al encenderse el osciloscopio conserva los ltimos ajustes configurados 4 2 del osciloscopio La bater a de litio estar posiblemente descargada al adquirir el equipo Para cargarla por completo debe ser cargada durante 4 horas estando el equipo desconectado Una vez completamente cargada la bater a puede suministrar energ a durante 4 horas Al utilizar el suministro de energ a de la bater a un indicador de bater a se visualiza en la parte superior de la pantalla para mostrar el estado de consumo el ctrico Los s mbolos que pueden aparecer son Mi Ml y LI El s mbolo fl muestra que a la bater a s lo le quedan aproximadamente 5 minutos de funcionamiento Para cargar la bater a e iniciar el equipo conecte el osciloscopio a un adaptador de energ a v ase la figura 1 La velocidad de carga se puede aument
39. OM V Q y mA para medici n de voltaje resistencia y corriente y las dos cuadrangulares CX para medir capacitancia V ase la Figura 1 5 3 Pantalla del mult metro Figura 33 Descripci n 1 Indicador del estado de carga de la bater a 2 Indicadores de rango MANUAL AUTO MANUAL indica el rango de medida en modo de operaci n manual y AUTOMATICO indica el rango de medida en modo de operaci n autom tico P gina 47 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX 3 Indicadores de modo de medida DCV medida de voltaje en continua ACV medida de voltaje en alterna DCA medida de corriente en continua ACA medida de corriente en alterna R medida de resistencia qh medida de diodo q C medida de capacitancia Medida con desc 4 Indicador de medida de magnitud relativa 5 Indicador del estado de actualizaci n de la pantalla RUN indica estado de medici n continua y STOP indica congelaci n del ltimo valor medido 6 Valor de referencia de la medida de magnitud relativa 7 Factor de multiplicaci n de la escala de medida Multiplic ndolo por la lectura de la escala de medida se obtendr el resultado de la medida 8 Unidad y valor de medida 9 Control autom tico del rango de medida Se activa pulsando F3 10 Control de medida de magnitud Absoluta Relativa el s mbolo II expresa una magnitud absoluta y A una magnitud relativa Control de medid
40. OS 782 OSCILOSCOPIO Y MULTIMETRO DIGITAL DIGITAL OSCILLOSCOPE amp MULTIMETER 0 1737 NOTAS SOBRE SEGURIDAD Antes de manipular el equipo leer el manual de instrucciones y muy especialmente el apartado PRESCRIPCIONES DE SEGURIDAD EI simbolo A sobre el equipo significa CONSULTAR EL MANUAL DE INSTRUCCIONES En este manual puede aparecer tambi n como s mbolo de advertencia o precauci n Recuadros de ADVERTENCIAS Y PRECAUCIONES pueden aparecer a lo largo de este manual para evitar riesgos de accidentes a personas o da os al equipo u otras propiedades SAFETY NOTES Read the user s manual before using the equipment mainly SAFETY RULES paragraph The symbol AN on the equipment means SEE USER S MANUAL In this manual may also appear as a Caution or Warning symbol Warning and Caution statements may appear in this manual to avoid injury hazard or damage to this product or other property SUMARIO CONTENTS Manual English MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX INDICE Eis rpiIic M 1 1 1 DESGH PDOT T s 1 2 Especificaciones Osciloscopio i 1 8 Especificaciones Mult metro essent 2 PRESCRIPCIONES DE SEGURIDAD ssesseeeneeee
41. ZXPROMAX MANUAL DE INSTRUCCIONES OS 782 Figura 44 Congelaci n de las lecturas en pantalla 5 6 Toma de una medida relativa Una medida relativa se define como el valor actual de una medida respecto al valor de una medida de referencia previamente fijada El siguiente ejemplo muestra como tomar una medida relativa Primero hay que adquirir un valor de referencia 1 2 Pulse la tecla R y la letra R aparecer en la parte superior de la pantalla Pulse la tecla AUTO SET hasta que aparezca la letra C en la parte superior de la pantalla Conecte el m dulo extendido de capacitancia en el conector jack de medida de capacidad Cuando la lectura se estabilice pulse la tecla F2 y el s mbolo AM aparece en la parte superior de la pantalla El valor de referencia guardado aparece debajo del s mbolo lt gt Conecte la capacitancia La lectura principal mostrada en pantalla es el valor real de la capacitancia En la pantalla se puede apreciar una imagen parecida a la de siguiente figura P gina 57 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX Figure 45 Medici n Relativa 5 7 Selecci n de rango autom tico manual El modo de selecci n de rango del equipo est predeterminado como autom tico Para cambiar a modo manual siga los siguientes pasos LE Pulse la tecla F1 y el s mbolo MANUAL aparecer en la parte superior de la pantalla 2 modo manual el rango de medida aumenta un nivel cada v
42. a manual 11 Control manual del rango de medida 12 Escala anal gica de medida Muestra el rango de medidas en el que se est trabajando Cada modo de test se presenta en un color diferente 5 4 Medir con el mult metro Pulsando la tecla DMM OSC el osciloscopio cambiar a modo de mult metro La pantalla mostrar la ventana del mult metro y al mismo tiempo solicitara que se inserten correctamente las puntas de prueba A continuaci n pulse cualquier tecla para entrar en el modo de medici n 02 2010 P gina 48 ZXPROMAX MANUAL DE INSTRUCCIONES OS 782 5 4 1 Medici n de valores de Resistencia Para medir una resistencia haga lo siguiente Pulse la tecla el simbolo aparecera en la parte superior de la pantalla Inserte el cable negro en la entrada COM tipo banana y el cable rojo en el la entrada V tipo banana Conecte el otro extremo de los cables rojo y negro a la resistencia que desea medir La lectura del valor de la resistencia se mostrara en la pantalla en Ohmios Ver Figura 34 Figura 34 Medida de resistencia 5 4 2 Medici n de un Diodo Para medir un diodo haga lo siguiente Pagina 49 Pulse la tecla R y el simbolo R aparecera en la parte superior de la pantalla Pulse la tecla AUTO SET el siguiente simbolo aparecera en dh pantalla Inserte el cable negro en la entrada COM tipo banana y el cable rojo en el la entrada V tipo banana Conecte el otro e
43. a a 20A La unidad de medida cambiara a A 3 Conecte el modulo adaptador de corriente en los terminales mA A COM y las puntas de prueba al m dulo 4 Conecte el otro extremo de los cables rojo y negro al punto que desea medir Active el circuito bajo prueba y la corriente de DC entre los puntos medidos se mostrar en pantalla Ver Figura 41 5 Pulse la tecla F4 para volver a rango de medida menor de 400 mA i DCA EB Figura 41 Medida de corriente en Corriente Continua hasta 20A 02 2010 P gina 54 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 5 4 8 Medici n de corriente en Corriente Alterna Aca Para realizar la medici n de corriente es necesario conectar en serie el medidor y el circuito bajo prueba Para realizar est operaci n es necesario desconectar el circuito antes de realizar dicha conexi n Para medir una corriente en CA menor de 400 mA haga lo siguiente 1 Pulse la tecla A y el s mbolo DCA aparecer en la parte superior de la pantalla La unidad de medida es mA Los s mbolos mA y 20A aparecer n en la parte inferior derecha de la pantalla Pulse F4 o F5 para cambiar el rango de medida de mA a 20A y viceversa 400mA esta seleccionado por defecto 2 Pulse la tecla AUTO SET y el s mbolo ACA aparecer en la zona superior de la pantalla 3 Inserte el cable negro en la entrada COM tipo banana y el cable rojo en el la entrada mA tipo banana 4 Conecte el otro extremo de l
44. alla Pulse entonces OSC A OSC Y y ver que la linea interrumpida V1 se desplaza arriba y abajo mientras el valor del voltaje medido de V1 en relaci n a la posici n cero de CH1 aparece en pantalla Pulse la tecla OSC OPTION repetidamente hasta que el mensaje A W CURSOR 2 aparezca en pantalla Pulse entonces OSC A OSC Y y ver que la l nea interrumpida V2 se desplaza arriba y abajo mientras el valor del voltaje medido de V2 en relaci n a la posici n cero de CH1 aparece en pantalla Adem s los valores absolutos de V1 y V2 se pueden visualizar en pantalla Ver Figura 24 f 51 2 SU Figura 24 Uso del cursor para una medida de voltaje Para hacer una medida de tiempo en CH1 haga lo siguiente P gina 39 Pulse la tecla MENU y el Men de Funciones aparecer a la derecha de la pantalla Pulse las teclas MENU A o MENU para seleccionar la funci n CURSORES Dos opciones aparecer n en la zona inferior de la pantalla Pulse la tecla F1 para seleccionar tipo de medida Tiempo Dos l neas interrumpidas verticales T1 y T2 aparecer n en pantalla Pulse la tecla F2 para seleccionar el canal medido CH1 Pulse la tecla OSC OPTION repetidamente hasta que el mensaje A V CURSOR 1 aparezca en pantalla Pulse OSC A OSCY y ver que la linea interrumpida T1 se desplaza a la derecha y a la izquierda mientras el valor del tiempo medido de T1 en relaci n a la posici n del punto central de la pantalla se visualiza en
45. ar apagando el equipo Para evitar un sobrecalentamiento de la bater a durante la carga la temperatura ambiente no debe exceder la recomendada las especificaciones t cnicas No es peligroso mantener conectando el cargador durante mucho tiempo ni siquiera varios d as El equipo reducir autom ticamente la velocidad de P gina 11 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX 4 3 Pantalla del osciloscopio En la Figura 2 se pueden observar las distintas partes de la pantalla del equipo 20 Figura 2 Pantalla del osciloscopio Descripci n 1 S mbolos que indican el estado de carga de la bater a a E y H 2 3 Indicadores de medidas 1 y 2 Se pueden mostrar diversos par metros Frecuencias f valor de pico Vp V valor medio etc Se pueden mostrar dos par metros de un mismo canal o un par metro para cada canal 4 El cursor indica la posici n horizontal de disparo 02 2010 P gina 12 5 10 11 12 13 14 15 16 17 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 Esta lectura da la diferencia de tiempo entre la posici n horizontal de disparo y la l nea central de la pantalla Marca cero cuando el cursor est en el centro de la pantalla El estado de disparo indica lo siguiente Auto El osciloscopio se encuentra en modo de disparo autom tico y adquiere formas de onda cuando no hay disparos Trig d El osciloscopio ha enviado un disparo y recoge la in
46. ct vertical scale reading Waveform is displayed normally Open the Invert function of the waveform setting 4 11 1 Setting the Channel Coupling With CH1 taken for example the measured signal is a sine wave signal containing a dc offset Press F1 Coupling first and then AC to make an ac coupling setting The dc component contained in the tested signal is blocked Press F1 Coupling first and then DC to make a dc coupling setting Both dc and ac components contained in the tested signal are permitted The waveform is displayed as the following figure 13 figure 14 f 1 005KHZ f 1 005KHZ Figure 13 AC coupling 02 2010 Page 24 users manuan os7ee f 1 005KHZ f 1 005KHZ LEFI RIGHT Tine Base UP DOWN CHi Vol Figure 14 DC coupling 4 11 2 Make Open and Close Settings on Channel With CH1 taken for example Press F2 Channel first then Close to make a Close setting on CH1 Press F2 Channel key first then Open to make an Open setting on CH1 4 11 3 Adjusting the Probe Scale It is necessary to adjust the probe attenuation scale factor correspondingly in the channel operation menu in order to comply with the probe attenuation scale If it is a 10 1 probe the scale of the input channel of the oscilloscope should be selected as 10X to avoid any error occurring in the displayed scale factor information and tested data Press F3 Probe to jump to the rela
47. dad tipo de disparo por video tipica Formatos de senal y velocidades AXPROMAX Amplitud de pico a pico de 2 divisiones de campo tipo de disparo de v deo Admite sistemas de difusi n NTSC PAL y MEDIDA Medida de cursores Medida autom tica ESPECIFICACIONES GENERALES Visualizaci n Tipo de pantalla Resoluci n de pantalla Colores de la pantalla Caracter sticas mec nicas Dimensiones Peso Alimentaci n Interna Externa Entrada Potencia de salida Corriente de salida Bater a Condiciones de funcionamiento Temperatura en funcionamiento Con adaptador de red Temperatura de almacenamiento Humedad en funcionamiento De0a10 C De 10 a 30 De 30 a 40 De 40 a 50 C Humedad de almacenamiento De 0 a 10 02 2010 SECAM para cualquier campo o l nea Diferencia de voltaje AV y diferencia de tiempo AT entre cursores Valor de pico a pico valor promedio valor eficaz frecuencia ciclo per odo valor m ximo valor m nimo valor tope valor base valor amplitud valor exceso valor defecto tiempo de subida tiempo de bajada Ancho Ancho Ciclo de funcionamiento Ciclo de funcionamiento retardo de subida y retardo de bajada 3 8 pantalla LCD color P xeles 320 horizontal X 240 vertical 4096 colores 180 A x 115 Al x 40 Pr mm 0 645 kg Bater a integrada recargable de Li lon 7 4 V Adaptador de red incluido para Europa y otros pa ses 100 240 VAC 50Hz 6W 8 5 V
48. de las tres teclas V A o R As el modo de medida se mostrar en pantalla Si el mensaje ERR no desaparece reinicie el osciloscopio 4 El valor de la amplitud del voltaje medido es 10 veces mayor o menor que el real en modo de osciloscopio Compruebe que el factor de atenuaci n del canal coincida con el factor de atenuaci n de la sonda utilizada 5 La forma de onda se visualiza en pantalla pero no es estable bajo en modo de osciloscopio e Compruebe que el ajuste de la se al en el men de modo de disparo coincide con el canal en uso e Compruebe el modo de disparo el modo de disparo por flanco es aplicable a una se al universal y el modo de disparo por v deo es aplicable a una se al de v deo La forma de onda solo ser estable cuando se seleccione el modo de disparo adecuado e Cambie el acoplamiento de disparo a HF Supresi n y LF Supresi n para filtrar las interferencias del ruido de disparo por HF o LF P gina 59 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX 02 2010 No hay ninguna visualizaci n en la pantalla al pulsar la tecla RUN STOP en modo de osciloscopio Compruebe que el modo de disparo en el men de modo de disparo est en disparo Normal o Individual y si el nivel de disparo est fuera del rango de la forma de onda En este caso seleccione la opci n de modo de disparo No Autom tico Pulse la tecla AUTO SET para completar los ajustes Al seleccionar el muestreo promedio en el modo de mu
49. desactivar la funci n Auto escala y si pulsa AUTOSET de nuevo el osciloscopio entra en modo Auto escala Desactive el submen en el men Auto escala Cuando la Auto escala est apagada active el submen entrando en la funci n Cuando se dispara en modo v deo la escala horizontal es 50 us Si un canal est mostrando una se al de flanco y el otro canal est una se al de v deo la escala de tiempo se refiere a 50us tanto a la se al de video como al flanco 4 22 Menu de estado del sistema Funci n ESTADO El men de estado de sistema es usado para mostrar la informaci n sobre los sistemas horizontal vertical de disparo y otros Para visualizar la informaci n del sistema haga lo siguiente 1 Pulse la tecla MENU y el Men de Funciones aparecer a la derecha de la pantalla Pulse las teclas MENU A o MENU Y para seleccionar la funci n ESTADO Cuatro opciones aparecer n en la zona inferior de la pantalla Pulse las teclas de F1 a F4 y la informaci n de estado correspondiente se mostrar en pantalla Ver Figura 30 Figura 30 Estado del sistema 4 23 Ajuste del eje horizontal Funci n HORIZONTAL Abra el men vertical de funciones y seleccione la funci n HORIZONTAL Los par metros configurables con las teclas F1 F5 aparecer n en la parte inferior de la P gina 43 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX pantalla El men HORIZONTAL se describe en la
50. dings are displayed on the screen in V Now you can see a screen that looks like the following Figure 35 Figure 35 Diode Measurement 5 4 3 On off test To perform an On off test do the following 1 Press the R key and R appears on the top of the screen 2 Press the AUTO SET key three times and the following is shown on the screen d 3 Insert the black lead into the COM banana jack input and the red lead into the V Q banana jack input 4 Connect the red and black leads to the test point If the resistance value of the tested point is less than 50 Q you will hear beep sound from the test tool Now you can see a screen that looks like the following Figure 36 02 2010 Page 52 users manuan os7ee O O Figure 36 On off test 5 4 4 Making a Capacitance Measurement To measure a capacitance do the following 1 Press the R key and R appears on the top of the screen 2 Press the AUTO SET key four times and C appears at the top of the screen 3 Insert the measured capacitance into the quadratic jack and the screen shows the capacitance reading NOTE When measured value is less than 5 nF capacitance please use small capacitance measurer of this multimeter and use relative value measuring mode to improve measuring precision It will take about 30seconds if capacitance measurement is large than 40uF Now you can see a screen that looks like the following figure 36 Figu
51. display style includes Vector and Dot displays shown as the following figure 20 figure 21 f 50HZ Figure 20 Dot style Figure 21 Vector style 4 16 2 Persistence With Persistence function selected the displayed saved original data gradually decay in color and the new data are bright in color with infinite persistence mode selected the recorded points will be kept on the screen till the controlled value is changed 02 2010 Page 34 users manua osz LAR PROMAXX 4 16 3 XY mode This mode is only applicable to CH1 and CH2 With the XY mode selected CH1 is displayed on the horizontal axis and CH2 is on the vertical axis when the oscilloscope is under the sampling mode in which no trigger is found the data appear in light spots Operations for various control keys are shown as below The CH1 VOL and CH1 ZORE for CH1 are used to set the horizontal scale and position e CH2 VOL and CH2 ZORE for CH2 are used to set the vertical scale and position continuously The following functions do not work in the XY display mode e Reference or digital value waveform e Cursor e Auto Setting e Time base control e Trigger control 4 17 Waveform Saving Setups The oscilloscope can save 4 waveforms which can be displayed on the screen with the present waveform The recalled waveform saved in the memory cannot be adjusted The waveform saving recalling menu is described in the fol
52. e the frequency of CH1 Freg Measure the frequency of CH2 Measure the Period of CH1 Period Measure the Period of CH2 Measure the average value of CHI Mean Measure the average value of CH2 Measure the peak to peak value of CH1 Measure the peak to peak value of CH2 Measure root mean square RMS value of CH1 Measure root mean square RMS value of CH2 Cyc RMS Measure the Vmax of CH1 Measure the Vmax of CH2 Measure the Vmin of CH1 Measure the Vmin of CH2 Vmax Page 37 02 2010 users manuan osz APRAX Function menu Settings Description Measure the Vtop of CH1 Measure the Vtop of CH2 Measure the Vbase of CH1 Measure the Vbase of CH2 Measure the Vamp of CH1 Measure the Vamp of CH2 Measure the Overshoot of CH1 Measure the Overshoot of CH2 Measure the Preshoot of CH1 Measure the Preshoot of CH2 Measure the RiseTime of CH1 Measure the RiseTime of CH2 Measure the Fall Time of CH1 Measure the Fall Time of CH2 Measure the Width of CH1 Measure the Width of CH2 Measure the Width of CH1 Measure the Width of CH2 Measure the Duty of CH1 Measure the Duty of CH2 Measure the Duty of CH1 Measure the Duty of CH2 Measure the DelayA 7B of CH1 Measure the DelayA B of CH2 Measure the DelayA Bt of CH1 Measure the DelayA B Y of CH2 Vtop Vbase Vamp Overshoot Preshoot Rise Time Fall Time Width Width Duty
53. eclas MENU A MENU Y para seleccionar la funci n SISTEMA y tres opciones aparecer n en la zona inferior de la pantalla 3 Pulse la tecla F1 RESET para seleccionar las configuraciones de f brica El osciloscopio recuperar entonces la configuraci n de f brica Ver Figura 9 Figura 9 Reiniciar el osciloscopio 4 7 Visualizaci n autom tica de una se al desconocida La funci n AUTOSET permite al osciloscopio mostrar y medir se ales desconocidas autom ticamente Esta funci n optimiza la posici n el rango la base de tiempo y el disparo y asegura una visualizaci n estable de pr cticamente cualquier forma de onda Esta funci n es especialmente til para identificar r pidamente varias se ales 02 2010 P gina 18 ZXPROMAX MANUAL DE INSTRUCCIONES OS 782 Para habilitar la funci n AUTOSET haga lo siguiente 1 Conectar la sonda de prueba a la se al 2 Pulse la tecla AUTOSET para poner el osciloscopio en modo de medida autom tica Las sefiales adquiridas aparecer n en pantalla 4 8 Puesta a cero autom tica de la posici n horizontal y el nivel de disparo Cuando se ajusta la posici n horizontal de disparo y la posici n de nivel de disparo para ser m xima pantalla entonces se realizan los siguientes pasos para que la posici n horizontal de disparo y la posici n de nivel de disparo vuelvan a cero autom ticamente 1 Pulse las teclas OSC lt y OSC DB simult neamente para que
54. ect Cursor measurement key Two key labels selectable are shown at the bottom of the screen Press the F1 key to the measurement type Time Two vertical dashed lines T1 and T2 appear on the screen Press the F2 key and jump to the measured channel CH1 Press and hold the OSC OPTION key till the A Y CURSOR T1 appears on the screen Then adjust the OSC A or OSC V and you can observe the dashed line moving left and right At the same time the time value of T1 relative to the screen middle point position will be displayed on the screen Keep pressing on the OSC OPTION key till the A Y CURSOR T2 is displayed on the screen Then adjust the OSC A or OSC Y and you can find that the dashed line T2 is moving right and left while the time value of T1 relative to the screen middle point position appears on the screen You can also observe the absolute time values and frequencies of T1 and T2 Now you can see a screen that looks like the following figure 25 02 2010 users manuan os7ee oO Oo CH2 OFF f 1 217KH2 Figure 25 Use the cursor for a time measurement 4 21 Autoscale The function is applied to follow up signals automatically even if the signals change at any time Autoscale enables the instrument to set up trigger mode voltage division and time scale automatically according to the type amplitude and frequency of the signals The menu is as follows Function menus Settings Description Autoscale
55. ejemplo muestra como usar la tecla OSC OPTION para hacer ajustes 1 Presione una vez la tecla OSC OPTION la siguiente informaci n aparecer en la esquina inferior izquierda de la pantalla como se muestra en la Figura 4 lt gt Time Base A V CH1 Volts DIV f 1 117KHZ Up 160 0mu E LEFT RIGHT Time Base UP DONN CH RC H2 1 000 Figura 4 Escala de unidad de voltaje de Canal 1 2 Pulse las teclas OSC A o OSC Y para ajustar la escala vertical de Canal 1 y OSC 4 o OSC gt para ajustar la escala de tiempo horizontal 3 Pulse OSC OPTION de nuevo EI siguiente texto aparecera en la esquina inferior izquierda de la pantalla como se muestra en la figura 5 lt gt Time Base A V CH2 Volts DIV P gina 15 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX 02 2010 f 1 130KHZ Up 160 Figura 5 Escala de unidad de voltaje de Canal 2 Pulse las teclas OSC A o OSC para ajustar la escala vertical de Canal 2 y OSC lt o OSC gt para ajustar la escala de tiempo horizontal Pulse OSC OPTION de nuevo El siguiente texto aparecer en la esquina inferior izquierda de la pantalla como se muestra en la figura 6 lt gt Tiempo CH1 Cero f 1 117KHZ Up 144 0mu IM 16 Time Figura 6 Posici n de punto cero del Canal 1 Pulse las teclas OSC A o OSC
56. el almacenaje 7 4 Sustituci n de la bater a de litio Normalmente no es necesario cambiar la bater a de litio Si fuera necesario reemplazarla s lo personal cualificado puede realizar esta operaci n Para m s informaci n p ngase en contacto con la oficina de PROMAX m s cercana o con su distribuidor P gina 61 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXAPROMAX 02 2010 P gina 62 TABLE OF CONTENTS 1 GENER L coins 1 1 1 Description iis 1 2 Specifications Oscilloscope seen 2 1 3 Specifications Multimeter eeeesesseeeseeeeeeeenne nennen 5 2 SAFETY RULES sd 2 1 General iate een tratada sf 2 2 Descriptive Examples of Over Voltage Categories id 3 DESCRIPTION FOR FRONT PANEL AND 4 USING THE iis 4 1 Power Up the OSCINOSCOPE occoononocorniosnonccnonnaracnnacaconccnncnnacanoncc noc nncnconos 4 2 Charging the oscilloscope o coonicninnonnoninninninncnncnaccnn canon no nana rnar can 4 3 Oscilloscope Operation Window vs 4 4 Navigating a Maru cocinan tia iterat nine 4 5 Manually Setting the Vertical System Horizontal System and Trigger Position 17 4 6 Resetting the Oscilloscope eese 4 7 Displaying an Unknown Signal with Auto Set 4 8 Automatic zero return
57. elect the ACQUIRE function The parameters to be modified with F1 F5 keys will appear in the lower part of the display The Acquiring Mode menu is described in the list shown as below Function menu Sampling Normal sampling mode Peak Used to detect the jamming glitch and reduce the possible Settings Description detection blurring Average Used to reduce the random and unrelated noises Several value average factors are available for being selected Average 4 16 640 Select the average factor factor 128 4 16 Display Setting Open the vertical menu of functions and select the DISPLAY function The parameters to be modified with F1 F5 keys will appear in the lower part of the display The Display Setting menu is described in the following table Function menu Settings Description Type Vector The vector is filled up spaces between neighboring sampling points in the display Dot Only sampling points are displayed Persistence Close Setting persistence time for each sampling point 1s 2s 5s Infinite Display format YT Display the relative relationship between vertical voltage and horizontal time Display CH1 on the XY horizontal axis and CH2 on the vertical axis Communication Bitmap The data transmitted in communication are bitmaps Vector The data transmitted in communication are vectors Page 33 02 2010 users manuan oszse O O 4 16 1 Display Style The
58. ento port til apto para realizar m ltiples medidas en exteriores donde trabajar con equipos convencionales resulta muy inc modo Es muy til en la medida de magnitudes el ctricas y en la reparaci n de equipos electr nicos dada su gran diversidad de funciones lo que hace que a su vez sea un elemento indispensable en laboratorios ya sea de investigaci n y desarrollo o de ense anza Las medidas realizadas por el equipo se presentan en una pantalla de cristal l quido de alta resoluci n con iluminaci n posterior Sus caracter sticas principales en cada uno de sus modos de funcionamiento son e Osciloscopio de dos canales ancho de banda de 20 MHz e Velocidad de muestreo de 100 MSa s e Sincron smo TV y sincron smo por flancos e 20 Medidas autom ticas e Funci n Autoescala Profundidad de memoria de 6k puntos por canal e Puerto USB e Mult metro digital de 3 34 para medidas de R V A y C e Adaptador AC y bater a de Ll ion Pantalla LCD color de 3 8 con retroiluminaci n 320 x 240 p xels e Cursores verticales y horizontales P gina 1 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXPROMAX 1 2 Especificaciones Osciloscopio A Todas las especificaciones se aplican a la sonda con un ajuste de atenuaci n 10X y al osciloscopio digital de serie HDS Para verificar que el osciloscopio cumple las especificaciones ste debe cumplir las siguientes condiciones El osciloscopio debe haber estado funci
59. er pulso negativo en el 50 de los puntos de amplitud Retraso 1 gt 2 El retardo entre los dos canales en el flanco de subida Retraso 152 retardo entre dos canales en el flanco de bajada Ciclo Ciclo de trabajo definido como Ancho per odo Ciclo Ciclo de trabajo definido como Ancho Per odo 4 20 Funci n CURSORES Este osciloscopio permite hacer medidas manuales con el cursor en tiempo y voltaje Las fuentes de se al incluyen Canal 1 CH1 y Canal 2 CH2 Los par metros Ajuste del cursor se describen en la siguiente tabla Par metros Tipo No Desactiva los cursores Voltaje Muestra la medida de voltaje con cursor Tiempo Muestra la medida de tiempo con cursor CH1 CH2 Selecciona el canal de forma de onda en el cual se medir con cursor Para hacer una medida de voltaje en CH1 haga lo siguiente 1 Pulse la tecla MENU y el Men de Funciones aparecer a la derecha de la pantalla 2 Pulse las teclas MENU o MENU Y para seleccionar la funci n CURSORES Dos opciones aparecer n en la zona inferior de la pantalla 3 Pulse la tecla F1 para seleccionar tipo de medida Voltage Dos l neas interrumpidas cruzadas de color violeta V1 y V2 aparecer n en pantalla 4 Pulse la tecla F2 para seleccionar el canal medido CH1 02 2010 P gina 38 AXxPROMAX MANUAL DE INSTRUCCIONES OS 782 Pulse la tecla OSC OPTION repetidamente hasta que el mensaje A V CURSOR 1 aparezca en pant
60. es digital type oscilloscope In order to be up to these specifications the oscilloscope should meet the following requirement e instrument should operate continuously for more than 30 minutes under the specified operating temperature If the operating temperature range of variation is up to or larger than 5 Celsius degrees the system function menu must be opened to make the system perform a self calibration procedure Except those specifications marked with the word Typical all specifications can be up to SAMPLING Sampling modes Sampling rate INPUT Input coupling Input impedance Probe attenuation coefficient Max Input voltage Channel delay time typical HORIZONTAL Sampling rate range Waveform interpolation Record length Scanning speed range S div Sampling rate and relay time accuracy Time interval T measurement Accuracy full bandwidth 02 2010 Normal sampling Peak detection Average value 100 MSa s DC AC Ground 1MQ 2 connected in parallel with 20pF 5 pF 1x 10x 100x 1000x 400V peak 150 ps 10S s 100MS s sin x x 6 K points on each channel 5ns div 100 s div stepping in the 1 2 5 5 100ppm any time interval which is equal to or larger than 1ms Single 1 sampling interval time 100 ppm reading 0 6 ns gt average 16 1 sampling interval time 100 ppm reading 0 4 ns Page 2 USER S MANUAL OS 782 VERTICAL Ana
61. est Make sure that the circuit is disconnected before doing this connection To measure an AC current which is less than 400 mA do the following 1 Press the A key and DCA appears at the top of the screen The unit on the main reading screen is mA mA and 20A will display on the right bottom of screen press F4 or F5 to switch the measurement between Ma and 20A 400 mA is acquiescently 2 Press the AUTO SET key once and ACA is visible at the top of the screen 3 Insert the black lead into the COM banana jack input and the red lead into the mA banana jack input 4 Connect the red and black leads to the measured point and the AC current value of the measured point will be displayed on the screen Look at the display you can see a screen that looks like the following figure 38 Figure 42 AC current Measurement for 400 mA To measure an AC current which is larger than 400 mA do the following 1 Press the AUTO SET key once and ACA is visible at the top of the screen 2 Press F5 to select 20 measure the unit of main reading window is A 3 Press the AUTO SET key once and ACA is visible at the top of the screen Page 57 02 2010 users manuan oszse O 4 Plug current extended module in current measure jack then plug the probe in the module 5 Connect the red and black leads to the measured point and the AC current value of the measured point will be displayed on the screen 6 Press F4 retur
62. estreo o seleccionar un tiempo de visualizaci n mayor en el modo de osciloscopio la velocidad de visualizaci n es lenta En este caso es lo normal P gina 60 Z amp PROMAX MANUAL DE INSTRUCCIONES OS 782 7 MANTENIMIENTO Y LIMPIEZA 7 1 Mantenimiento b sico No almacene o coloque el equipo en lugares donde la pantalla de cristal l quido quede directamente expuesta a la luz del sol durante mucho tiempo No roc e el equipo ni las sondas con agentes l quidos o disolventes para prevenir que se da en 7 2 Limpieza Inspeccione el equipo y la sonda con frecuencia seg n las condiciones de utilizaci n Para limpiar la superficie externa del instrumento siga los pasos siguientes 1 Limpie el polvo de la parte exterior del equipo y la sonda con un pa o suave Al limpiar la pantalla de cristal l quido no raye la pantalla protectora transparente 2 Limpie el equipo s lo cuando est apagado con un pa o suave previamente humedecido pero no empapado Se puede utilizar un detergente suave o agua No use ning n detergente qu mico abrasivo para evitar da os en el equipo o la sonda AN Antes de volver a encender y utilizar el equipo por favor aseg rese de que se ha secado completamente para evitar cortocircuitos y da os personales debido a la humedad Advertencia 7 3 Almacenaje de osciloscopio Si el equipo debe permanecer almacenado durante mucho tiempo se debe recargar la bater a de litio antes d
63. ez que se pulsa F1 y al alcanzar el nivel m s alto vuelve al nivel m s bajo pulsando F1 una vez m s Multiplicando el Factor de multiplicaci n de la escala de medida por la lectura de la escala de medida se obtendr el resultado de la medida 3 Para volver a modo autom tico pulse la tecla F3 y el s mbolo AUTO aparecer en la parte superior de la pantalla Ver Figura 46 Figura 46 Selecci n de rango autom tico manual ATENCI N Medici n de la capacitancia sin modo de rango manual 02 2010 P gina 58 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 6 POSIBLES PROBLEMAS Y SOLUCIONES 1 El osciloscopio no se enciende La bater a puede estar agotada En este caso el osciloscopio no arrancar incluso si se conecta al cargador de bater a En primer lugar cargue la bater a conectando el osciloscopio al cargador Sin embargo no encienda el osciloscopio hasta despu s de 15 minutos Si a n as el osciloscopio no puede arrancar por favor p ngase en contacto con el servicio t cnico de PROMAX 2 El osciloscopio funciona durante unos segundos y se apaga Probablemente la bater a est agotada Compruebe el s mbolo de la bater a en la esquina superior derecha de la pantalla El s mbolo fl indica que la bater a est agotada y debe ser cargada 3 El mensaje ERR aparece en pantalla al encender el mult metro Probablemente el mult metro no est en modo de medida En este caso pulse cualquiera
64. formaci n generada como consecuencia del disparo Ready Se han adquirido todos los datos del antes de disparo y el osciloscopio est preparado para aceptar un disparo Scan El osciloscopio adquiere y muestra continuamente datos de forma de onda en modo de exploraci n Stop El osciloscopio ha interrumpido la adquisici n de datos de forma de onda El indicador verde se ala el nivel de voltaje de disparo Men principal del osciloscopio Pulsando el bot n MENU se visualiza esconde este men Opciones del men hay diferentes par metros de ajuste para cada opci n del men Muestra el valor del nivel de voltaje de disparo Muestra la fuente de se al de disparo Muestra el valor de la base de tiempo primaria stos gr ficos presentan los modos de acoplamiento del canal CH2 indica Acoplamiento AC y indica acoplamiento DC Muestra el valor V div vertical del canal CH2 stos gr ficos presentan los modos de acoplamiento del canal CH1 indica o acoplamiento AC y indica acoplamiento DC Muestra el valor V div vertical del canal CH1 El indicador azul muestra la posici n cero de CH2 Si el canal CH2 se desactiva desaparece el indicador P gina 13 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX 18 Indicaciones OSC OPTION Con cada pulsaci n de OSC OPTION se muestran par metros modificables mediante las teclas de cursor 4 gt A y V 19 El indicador ro
65. frecuencia de de la se al se bloquea y s lo se permite el componente de baja frecuencia La parte de baja frecuencia de de la se al se bloquea y s lo se permite el componente de alta frecuencia Conceptos b sicos Vuelve al men anterior Modos de disparo Hay tres modos de disparo disponibles para este osciloscopio que son autom tico normal y disparo nico 1 Modo de disparo autom tico P gina 27 El osciloscopio puede adquirir la forma de onda sin que se detecten condiciones de disparo En este modo el disparo ser provocado peri dicamente si durante un per odo especificado del tiempo no se han dado condiciones de disparo 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX 2 Modo de disparo normal En este modo el osciloscopio no puede adquirir la forma de onda si no se provoca un disparo Cuando no hay un disparo el osciloscopio mostrar la forma de onda de origen sin actualizar 3 Disparo nico En este modo el osciloscopio detecta el disparo y adquiera una forma de onda cada vez que el usuario pulsa la tecla RUN STOP 4 14 2 Men s de disparo por video En modo de disparo por video el osciloscopio muestra formas de onda de v deo compuesto en est ndar NTSC o PAL SECAM Se dispara en l neas campos pares campos impares o por n mero de l nea de se al de video Ver Figuras 17 y 18 f 66 67KHZ f 66 67HH2 Figura 18 Disparo en l nea de
66. ically returns to zero 2 Press OSC A and OSC V button simultaneously the trigger level position automatically returns to zero 4 9 Automatic Measurements The Oscilloscope offers 20 ranges of automatic scope measurements Your can display two numeric readings measurement 1 and measurement 2 These measures are shown in the left upper part of the display and can be shown two parameters of a same channel or a parameter of each channel To choose a frequency for CHI1 do the following 1 Press MENU key and the function menu appears on the right side of the screen 2 Press MENU A or MENU key to select measurement 1 Five items selectable are visible at the bottom of the screen 3 Press F1 key and select Freq CH1 from the mean square root value item The measurement 1 window turns its color into red and shows the frequency for input CHI NOTE When pressing the F1 F5 keys the measured channel CH1 CH2 changes alternatively Page 21 02 2010 users manuan os7ee To choose a Peak Peak measurement for Input CH2 do the following 1 Press MENU key and the function menu is displayed on the right side of the screen 2 Press MENU A or MENU V key and select Measurement 2 with 5 items selectable displayed at the bottom of the screen 3 Press F4 key to select PK PK CH2 from Peak Peak item The measurement 2 window turns its color to be blue and shows the peak peak value for inp
67. idity Warning 7 3 Storage of oscilloscope If the equipment is stored during long time the lithium battery must be recharged before the storage 7 4 Substitution of the battery of lithium Normally it is not necessary to change the battery of lithium If it was necessary to replace her only qualified personnel can realize this operation For more information put in touch with the PROMAX most nearby office or with his distributor Page 63 02 2010 users manuan osz APRAX 02 2010 Page 64
68. ing of trigger horizontal position and trigger level position as 21 4 9 Automatic Measurements 4 10 Freezing the 4 11 Setting the Vertical CH1 and CH2 ates 4 11 1 Setting the Channel Coupling 24 4 11 2 Make Open and Close Settings on Channel 12D 4 11 3 Adjusting the Probe Scale esses eene tentent anat 25 4 11 4 Setting of Inverted Waveform oooonnnccccicicnnnninnnnnanananinananananar ano nar ann na nanannnn 26 4 12 MATH function MATH iss 4 13 Setting the Trigger System TRIGGER 27 Triggering CohtrOl cerne err ii 28 4 14 1 Edge triggering 29 Description 29 4 14 2 Video triggering 30 4 15 Acquiring Mode Setting ss 33 4 16 Display Setting 39 Settings 33 4 16 1 Display Style 34 4 16 2 Persistence we 34 ENT adu X OE 35 4 17 Waveform Saving Setups cinis secet 35 4 18 Function Setting Menu 4 19 Making Automatic Measurements occocnnccnocnnononnncnnnnncnnnan cnn c rca non nncncanr cnn nancano 37 4 20 Setting the Cursor Measurements sess 40 4 21 Autoscale ene 42 4 22 System State 45 4 23 Horizontal axis
69. ingle shot and whether the trigger level is out of the waveform range In such condition adjust and make the trigger level in the middle or select the non auto trigger mode Additionally press the AUTO SET key and complete the above setting When select the average sampling in the sampling mode or select a longer display time in the display mode under the oscilloscope the display speed is slow It is normal in the above case Page 62 users manuan osz PROMA 7 MAINTENANCE AND CLEANING 7 1 Basic maintenance Do not store or place the instrument in locations where the liquid crystal display is exposed directly to the light of the sun during long time 7 2 Cleaning Usually inspect the equipment and the probes according to the conditions of use In order to clean the external surface of the instrument you must follow these instructions 1 Clean the dust of the external parts of the instrument and the probes with a smooth cloth When cleaning the liquid crystal display avoid to damage the protective transparent layer 2 Only clean the equipment when it is power off with a previously dampened but not soaked smooth cloth A light detergent or water can be used Do not use any abrasive chemical detergent to avoid damages in the equipment or the probes AN Before back to power on and to use the instrument please make sure that it has been completely dried to avoid short circuits and personal hazards due to the hum
70. io OS 782 dispone de un puerto USB que permite transmitir los datos mostrados y o memorizados de el equipo al ordenador Con el equipo se adjunta un CD con el programa de comunicaci n Para su instalaci n siga los siguientes pasos 1 Inserte el CD en el lector de discos 2 Abra el explorador y ejecute el fichero Setup exe y siga las instrucciones del instalador Por defecto el programa se instala en la carpeta c Archivos de programa PROMAX OS Wave Oscilloscope Acceda al men Help del programa para cualquier consulta P gina 45 ee MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX 02 2010 Una vez instalado conecte el cable USB entre el equipo y el PC Encienda el equipo Automaticamente el PC detectara un nuevo equipo y le pedira de instalar el driver correspondiente Seleccione el m todo avanzado de instalaci n en la siguiente pantalla seleccione la carpeta USBDRV que hay dentro del directorio donde se ha instalado el programa Pulse Siguiente para instalar el driver Ahora ya puede abrir el programa DS Wave para la captura de datos en el PC P gina 46 ZXPROMAX MANUAL DE INSTRUCCIONES OS 782 5 UTILIZACION DEL MULTIMETRO 5 1 Sobre este capitulo Este cap tulo es una explicaci n paso a paso a las funciones del multimetro del equipo La introducci n da ejemplos para mostrar c mo usar los men s y realizar operaciones b sicas 5 2 Conexiones del mult metro Use las tres entradas de seguridad tipo banana C
71. jo muestra la posici n cero de CH1 Si el canal CH1 se desactiva desaparece el indicador 20 Area de visualizaci n de las formas de onda La forma de onda roja representa CH1 y la forma de onda azul representa CH2 4 4 Navegaci n por los men s Este ejemplo muestra c mo usar los men s del equipo para seleccionar cada funci n como se ve en la siguiente figura 1 Pulse la tecla MENU para mostrar el Men de Funciones a la derecha de la pantalla y los correspondientes par metros u opciones en la parte inferior de la pantalla Para ocultar el Men de Funciones pulse de nuevo la tecla MENU Pulse las teclas MENU A y MENU Y para seleccionar funciones Pulse una tecla de F1 a F5 para modificar los diversos par metros de cada funci n f 1 005KHZ f 1 005KHZ Figura 3 Herramientas del men 02 2010 P gina 14 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 4 5 Ajuste manual de los ejes vertical y horizontal y de la posici n de disparo Combinando las cuatro teclas DSC OSC gt OSC A y OSC se pueden hacer las configuraciones siguientes pulsando OSC OPTION Las configuraciones incluyen escala vertical del Canal 1 CH1 VOL escala vertical del Canal 2 CH2 Volts div Base de tiempos primaria Tiempo div punto cero del Canal 1 CH1 CERO punto cero del Canal 2 CH2 CERO posici n horizontal de disparo TIEMPO y posici n del nivel de disparo TRIG El siguiente
72. juste Descripci n funci n ACOPLO AC El componente DC de la se al de entrada se bloquea DC Los componentes AC y DC de la se al de entrada se Masa permiten ACTIVADO Activa el canal Desactiva el canal SONDA Seleccione un ajuste seg n el factor de atenuaci n de la sonda para asegurar una correcta lectura de la escala vertical INVERTIDO La forma de onda se muestra normalmente i Invierte la se al 180 4 11 1 Ajuste del acoplo del canal Tomando como ejemplo CH1 la se al medida es una se al de onda sinusoidal que contiene un componente DC Pulse F1 Acoplo y seleccione AC para ajustar acoplamiento AC El componente DC de la se al quedar bloqueado Pulse F1 Acoplo y seleccione DC para ajustar acoplamiento DC Los componentes CA y DC de la se al quedar n permitidos Ver Figuras 13 y 14 f 1 005KHZ f 1 005KHZ Figura 13 Acoplamiento de Corriente Alterna 02 2010 P gina 22 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 f 1 005KHZ f 1 005KHZ Figura 14 Acoplamiento de Corriente Continua 4 11 2 Configuraci n de activaci n desactivaci n del canal Tomando como ejemplo CH1 Pulse F2 Activado y seleccione No para desactivar el canal CH1 Pulse F2 Activado y seleccione Si para activar el canal de CH1 4 11 3 Ajuste de la escala de sonda Hay que ajustar el factor de atenuaci n de la sonda proporcionalmente en el men de operaci n del canal para reflejar la
73. l CH2 is deactivated this indicator disappears Page 15 02 2010 users manuan os7ee O oO Oo 18 OSC OPTION indications Whenever you press the OSC OPTION they are shown parameters to be modified by means of the cursor keys gt and 19 The indicator shows the CH1 zero position If channel CH1 is deactivated this indicator disappears 20 Waveform display area Red waveform represent CH1 blue waveform represent CH2 4 4 Navigating a Menu The following example shows how to use the tool s menus to select a function as shown in the following figure 1 Press the MENU key to show the Functions Menu in the right side of the display and the corresponding parameters or options in the lower part of the display In order to hide the Functions Menu press the MENU key again Press the MENU A or MENU Y key to select different function menus Press a key from F1 to F5 to modify the diverse parameters of each function f 1 005KHZ f 1 005KHZ Figure 3 The tool s menus 02 2010 Page 16 users manuan oszse Oo o 4 5 Manually Setting the Vertical System Horizontal System and Trigger Position With the combination application of the four keys OSC lt OSC gt OSC A and OSC the users can make the following settings circularly by pressing OSC OPTION The settings include Voltage Unit Scale of Channel 1 CH1 VOL Voltage Unit Scale of
74. la posici n horizontal de disparo vuelva autom ticamente a cero 2 Pulse las teclas OSC y OSC Y simult neamente que la posici n de nivel de disparo vuelva autom ticamente a cero 4 9 Medidas autom ticas El osciloscopio ofrece 20 tipos de medidas autom ticas Su pueden mostrar simult neamente dos lecturas num ricas Medida 1 y Medida 2 Estas medidas se muestran en la parte superior izquierda de la pantalla y pueden ser mostrados dos par metros de un mismo canal o un par metro de cada canal Para seleccionar una frecuencia para CH1 haga lo siguiente 1 Pulse la tecla MENU y el Men de Funciones aparecer a la derecha de la pantalla 2 Pulse las teclas MENU A o MENU para seleccionar Medida 1 Cinco opciones aparecer n en la zona inferior de la pantalla 3 Pulse la tecla F1 y seleccione Freq CH1 La ventana de Medida 1 se vuelve roja y muestra la frecuencia para la entrada del CH1 NOTA Con cada pulsaci n de las teclas F1 F5 cambia alternativamente el canal medido CH1 CH2 P gina 19 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX Para seleccionar una medida de Pico Pico para CH2 haga lo siguiente NOTA Pulse la tecla MENU y el Men de Funciones aparecer a la derecha de la pantalla Pulse las teclas MENU A o MENU VW para seleccionar Medida 2 Cinco opciones aparecer n en la zona inferior de la pantalla Pulse la tecla F4 para seleccionar Vpp CH2
75. ll be displayed Figure 30 System State 02 2010 users manuan osz APRAX 4 23 Horizontal axis setting HORIZONTAL function Open the vertical menu of functions and select the HORIZONTAL function The parameters to be modified with F1 F5 keys will appear in the lower part of the display The time base mode menu is explained as the following table Main time base Horizontal main time base is used to wave display Zone Window Use two cursors to define a window area Window extensi n Expand the defined window to full screen display For the operation of window extension please execute the following steps 02 2010 Press MENU key display the function menu on the right side of the screen Press MENU A or MENU key to select time base mode display three options at the bottom Press F2 key to select window setting Press OSC OPTION key pop up TIME BASE at this time then press OSC lt OSC gt key to adjust the time base window area defined by two cursors the window size will vary Press OSC OPTION key and call OSC OSC to adjust the window position defined by two cursors the window position is the time difference of the window center to main time base s horizontal pointer Press F3 key select window extension the defined window extends into the full screen display The screen that looks like the following figure 27 28 will be displayed Page 46 users manuan os7ee
76. log digital converter A D Sensitivity range V div Displacement range Analog bandwidth Single bandwidth Low frequency response coupling AD 3dB Rise time typical one at the BNC DC gain accuracy DC measurement accuracy average value sampling mode Trigger AXPROMAX With the resolution of 8 bits make sampling on both channels synchronously 5mV div 5V div at the input BNC 50 V 500 mV 5 V 2 V 5 mV 200 mV 20 M Ancho de banda completo gt 5Hz at the BNC lt 17 5ns 5 The voltage difference V between any two points on the waveform after averaging the captured waveforms more than16 5 reading 0 05 divisions Trigger sensitivity Edge triggering DC coupling AC coupling Triggering lever range Triggering level accuracy typical which is applicable to the signal with rise and fall time equal to or longer than 20ns Trigger displacement Trigger Holdoff range Make a 50 level setting Typical Trigger sensitivity Video Triggering and typical mode Signal system and line field Measurement Cursor measurement Auto measurement Page 3 CH1 and CH2 1div DC full bandwidth Same as the DC coupling when it is equal to or larger than 50Hz 6 divisions from the screen center 0 3 divisions 655 divisions for pre triggering and 4 divisions for post triggering 100 ns 10 s Operation with the input signal frequency equal to or larger than 50Hz 2 divisions
77. lores de Resistencia oonocinnicnncinnncnnnccnocccncncnncnnnrn care nana nano 49 5 4 2 Medici n de un Diodo 49 5 4 3 Prueba continuidad 50 5 4 4 Medici n de una Capacitancia ib 5 4 5 Medici n de voltaje en Corriente Continua VDC 52 5 4 6 Medici n de voltaje en Corriente Alterna VAC 52 5 4 7 Medici n de corriente en Corriente Continua ADC 53 5 4 8 Medici n de corriente en Corriente Alterna ACA 4 55 5 5 Congelaci n de las lecturas en pantalla 56 5 6 de una medida relativa sess 57 5 7 Selecci n de rango autom tico manual esee 58 6 POSIBLES PROBLEMAS Y SOLUCIONES sess nne 59 7 MANTENIMIENTO Y LIMPIEZA esses nennen nennen 61 7 1 Mantenimiento b sico 2 61 7 2 Limpieza 61 7 3 Almacenaje de osciloscopio 61 7 4 Sustituci n de la bater a de litio ocooccccnoccccnoocnnnnoncnononnnonnonncnanrnncnnnnnnnnns 61 Z amp PROMAX MANUAL DE INSTRUCCIONES OS 782 Osciloscopio y Multimetro Portatil Digital OS 782 1 GENERALIDADES 1 1 Descripci n El Poliscopio OS 782 integra en si mismo dos instrumentos de medida osciloscopio digital y mult metro digital Su robusta construcci n tama o peso y alimentaci n mediante bater as hacen de l un instrum
78. lowing list Function menu Description Signal source Select the displayed waveform which you want to save Wave Select the address for saving or recalling a waveform Saving Store the waveform of a selected signal source into the selected address Addresses A B Close or start displaying the waveforms stored in C D address A B C or D Page 35 02 2010 users manuan oszse oO o To save a waveform on CH1 in address A do the following 1 Press the MENU key and the function menu appears at the right of the screen 2 Press the MENU A or MENU Y key to select the Waveform Saving Four items selectable are displayed at the bottom of the screen 3 Press the F1 key to select the signal source CH1 4 Press the F2 key to select the address A 5 Press the key to save the waveform on CH1 in address A To display the saved waveform on the screen do the following 6 Press the F4 key to select Start for the address A The waveform saved in address A will be displayed on the screen in green color The display color is green and the zero point of waveform k voltage and time is purple Now you can see a screen that looks like the following figure 22 Figure 22 Waveform Saving 4 18 Function Setting Menu Open the vertical menu of functions and select the SYSTEM function The parameters to be modified with F1 F5 keys will appear in the lower part of the display
79. mall capacitance One AC power adapter for Europe and other countries AL782 A User Manual 0 MI 1452 An operational optical disk A software CD 02 2010 Page4 AXPROMAX USER S MANUAL OS 782 1 3 Specifications Multimeter Maximum tension of the points of measure to land 400V CAT II Voltage VDC Input Impedance 10MQ 400 mV 100 uV 4 000 V T 1 mV 1 1 digit 40 00 V 5 10 mV 400 0 V 100 mV Input protection 1000 VDC or peak AC Voltage VAC Input Impedance 10M Frequency range Display from 40 Hz to 400 Hz Virtual value of the sine wave x 1 x 3 digits Input protection Direct Current ADC 1 750 VDC or peak AC 40 00 mA x 1 1 digit 400 0 mA 1 5 1 d gito 20A 2 Alternating Current AAC 1 3 3 d gitos 40 00 mA 1 5 digits 400 0 mA 2 1 digit 20A 2 1 ATENTION Not to overcome in any case 400mA or 20A respectively 2 With the extension module of measure of current Page 5 5 digits 02 2010 users manua osz LAR PROMAX Resistance 400 0 Q 1 3 digits 4 000k Q 40 00k Q 1 1 digit 400 0k Q 4 000 40 00 1 5 3 digits Capacitance 51 20 nF 512 0 nF 5 120 uF 3 digits 51 20 uF Diode Voltage reading OV 1 5V On off Test You can a beep sound when the on
80. matem ticas 4 13 Ajuste del sistema de disparo Funci n TRIGGER 4 14 Control de disparo eene 4 14 1 Disparo por Flanco 4 14 2 Men s de disparo por 4 15 Ajustes del modo de adquisici n FUNCI N ADQUIRIR 4 16 Ajustes de pantalla Funci n DISPLAY 31 Configuraciones 4 16 1 Estilo de visualizaci n iis 4 16 2 Persistencia nr iiti tn i PR det peche co rs a rss 4 16 3 O pegue R 4 17 Ajustes para guardar las formas de onda Funci n MEMORIA ace 4 18 Men de Sistema Funci n SISTEMA sse 4 19 Medidas autom ticas Funciones MEDIDA 1 y MEDIDA 2 4 20 Funci n CURSORES sse 4 21 Auto Escala nndis 4 22 Men de estado del sistema Funci n ESTADO 4 23 Ajuste del eje horizontal Funci n HORIZONTAL AT 4 24 Transmisi n de datos al PC AxPROMAX MANUAL DE INSTRUCCIONES OS 782 5 UTILIZACI N DEL MULTIMETRO sccscsssessecsessseeseesecsessscesecseesecsuseseeseeseeseesneenes 47 5 1 Sobre este Capitulo uu id diia 47 5 2 Conexiones del mult metro ie eiui netten erre eek e ice 47 5 3 Pantalla del mult metro 5 4 Medir con el Multimetto miss 48 5 4 1 Medici n de va
81. n to 400mA measure i Figure 43 AC current Measurement for 20A 5 5 Freezing the Readings You can freeze the displayed readings at any time 1 Press the RUN STOP key to freeze the screen and STOP will be displayed at the top right of the screen 2 Again press the RUN STOP key you can resume your measurement Look at the display you can see a screen that looks like the following figure 40 02 2010 Page 58 users manuan os7ee Figure 44 Freezing the Readings 5 6 Taking a relative measurement A currently measured result relative to the defined reference value is displayed in a relative measurement The following example shows how to take a relative measurement At first it is required to acquire a reference value a Press R key and R is displayed on the top side of the screen Press the AUTO SET key till C appears at the top of the screen Plug capacitance extended module in capacitance measure jack a When the reading leveling off press F2 key and A is displayed on the top side of the screen The saved reference value is displayed below A 5 Plug capacitance the displayed major reading on the screen is actual the capacitance value Look at the display you can see a screen that looks like the following figure 32 Page 59 02 2010 users manuan oszee Figure 45 Relative Measurement 5 7 Selecting automatic manual range adj
82. neeneneene trennen 7 241 Generales iini ierit idees etia un 2 2 Ejemplos Descriptivos de las Categor as de Sobretensi n 8 3 DESCRIPCI N DE MANDOS Y ELEMENTOS sccscssessessesesesseesecsesesessesseeseseess 9 4 UTILIZACI N DEL OSCILOSCOPIO scssssscssesssstsscesecsessessesteseeseaseateseeseaneseseaes 11 4 1 Encendido del osciloscopio 4 2 del osciloscopio 4 3 Pantalla del osciloscopio 4 4 Navegaci n por los men s 4 5 Ajuste manual de los ejes vertical y horizontal y de la posici n de disparo 15 4 6 Reiniciar el osciloscopio oooonnnccnnocnnonnnnnannarnconnnnnn cnn nc nnncnnrn cnn conan nnne aa 18 4 7 Visualizaci n autom tica de una se al desconocida 18 4 8 Puesta a cero autom tica de la posici n horizontal y el nivel de disparo 19 49 Medidas autom ticas eerie ottiene cicatrices enata specus 4 10 Congelaci n de la imagen en 4 11 Ajuste del eje vertical de CH1 y CH2 Funci n CANAL 1 CANAL 2 eT 4 11 1 Ajuste del acoplo del canal oconnccnnccinocanacanannnonnnnananancc nan n nn n aran c rc nnnncnnnns 4 11 2 Configuraci n de activaci n desactivaci n del canal 4 11 3 Ajuste de la escala de 4 11 4 Ajuste de forma de onda invertida 4 12 Funciones
83. o puede guardar hasta 4 formas de onda que se pueden mostrar en pantalla con la forma de onda actual Las formas de onda memorizadas no se pueden modificar El menu de Memorizar Recuperar formas de onda se describe en la siguiente tabla Par metros Configuraciones Descripci n Fuente CH1 CH2 MATH Selecciona la forma de onda visualizada que se quiere memorizar Onda A B C D Selecciona la direcci n para guardar o recuperar una forma de onda Guardar Almacena la forma de onda de una fuente de se al seleccionada en la direcci n seleccionada Mostrar Cierra o inicia la visualizaci n de las formas de onda memorizadas en las direcciones A B C D Para guardar una forma de onda en CH1 en la direcci n A haga lo siguiente 1 Pulse la tecla MENU y el Men de Funciones aparecer a la derecha de la pantalla 2 Pulse las teclas MENU A o MENU Y para seleccionar MEMORIA Cuatro opciones aparecer n en la zona inferior de la pantalla 3 Pulse la tecla F1 para seleccionar la fuente de se al de CH1 P gina 33 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX 4 Pulse la tecla F2 para seleccionar la direcci n A 5 Pulse la tecla F3 para guardar la forma de onda de CH1 en la direcci n A Para visualizar la forma de onda memorizada haga lo siguiente 6 Pulse la tecla F4 para seleccionar Si para la direcci n A La forma de onda guardada en la direcci
84. on adjustment OSC OPTION Oscilloscope setting key With the combination application of the four keys OSC lt OSC gt OSC A y OSC the users can make the following settings circularly by pressing OSC OPTION The settings include Voltage Unit Scale of Channel 1 CH1 VOL Voltage Unit Scale of Channel 2 CH2 VOL Primary Timebase TIME BASE zero point position of channel 1 CH1 ZERO zero point position of channel 2 CH2 ZERO trigger horizontal position TIME and trigger level position TRIG e When performing Waveform Calculation the users can also adjust and calculate the Display Multiplying Factor of waveform CHM VOL and the vertical display position CHM ZERO In cursor measurement mode the users can adjust the positions of Cursor 1 V1 or T1 and Cursor 2 V2 or T2 OSC Oscilloscope display downward adjustment key OSC A Oscilloscope display upward adjustment key OSC DMM Operation mode switching key between oscilloscope and multimeter AUTOSET Oscilloscope AUTOSET setting key e Under the Multimeter Mode when performing the current or voltage measurement you can make a measurement switch between AC and DC with this key pressed when performing the resistance measurement you can select resistance diode On Off or capacitance measurement circularly with this key e While this key is used for auto setting under the oscilloscope operation mode RUN STOP key fo
85. onando de forma continua durante treinta minutos en un ambiente con la temperatura de funcionamiento especificada Debe realizar un Auto calibrado al que se accede mediante el Men de funciones si la temperatura de funcionamiento cambia en m s de 5 C Todas las especificaciones est n garantizadas excepto las que se indican como t picas MUESTREO Modos de muestreo Velocidad de muestreo ENTRADA Acoplamiento de entrada Impedancia de entrada Coeficiente de atenuaci n de sonda Tensi n m xima de entrada Retraso del canal t pico HORIZONTAL Rango de velocidades de muestreo Interpolaci n de formas de onda Longitud de registro Rango de velocidad de escaneo S div Precisi n de velocidad de muestreo y de tiempo de retardo 02 2010 Muestreo normal Detecci n de picos Valor promedio 100 MSa s DC AC Tierra 1MO 2 20pF 5pF conectado en paralelo con 1x 10x 100x 1000x 400V pico 150ps 10S s 100MS s sin x x 6 K puntos por canal 5ns div 100s div en pasos de 1 2 505 100 ppm sobre cualquier intervalo de tiempo de igual mayor que 1 ms Pagina 2 AxPROMAX Precisi n de medida del tiempo t de diferencia ancho de banda completo VERTICAL Conversor digital anal gico A D Rango de sensibilidad V div Rango de desplazamiento Ancho de banda anal gica Ancho de banda nica Respuesta de baja frecuencia Acoplamiento AD 3dB Tiempo de s
86. os cables rojo y negro al punto que desea medir Active el circuito bajo prueba y la corriente de CA entre los puntos medidos se mostrar en pantalla Ver Figura 42 Figura 42 Medida de corriente en Corriente Alterna hasta 400 mA Para medir una corriente en CA mayor de 400 mA haga lo siguiente 1 Pulse la tecla AUTO SET y el s mbolo ACA aparecer en la zona superior de la pantalla 2 Pulse F5 para cambiar el rango de medida a 20A La unidad de medida cambiar a A 3 Pulse la tecla AUTO SET y el s mbolo ACA aparecer en la zona superior de la pantalla P gina 55 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX Conecte el modulo adaptador de corriente en los terminales mA A COM y las puntas de prueba al m dulo Conecte el otro extremo de los cables rojo y negro al punto que desea medir Active el circuito bajo prueba y la corriente de CA entre los puntos medidos se mostrar en pantalla Ver Figura 43 Pulse la tecla F4 para volver a rango de medida menor de 400 mA Figura 43 Medida de corriente en Corriente Alterna hasta 20A 5 5 Congelaci n de las lecturas en pantalla Las lecturas mostradas en pantalla pueden ser congeladas en cualquier momento 1 02 2010 Pulse la tecla RUN STOP para congelar el valor en la pantalla y el s mbolo STOP aparecer en la esquina superior derecha de la pantalla Ver Figura 44 Pulse de nuevo RUN STOP para reanudar la medida P gina 56
87. ources CH2 measurement will be performed To make a voltage measurement on CH1 doing the following 1 Press the MENU key and the function menus are displayed at the right of the screen 2 Press the MENU A or MENU Y key to select Cursor Measurement Two options are shown at the bottom of the screen 3 Press F1 key to select the measurement type Voltage Two purple crossing dashed lines V1 and V2 are shown on the screen 4 Press the F2 key to select the measured channel CH1 5 Press and hold the OSC OPTION key till the A V CURSOR V1 is visible on the screen At this time adjust OSC or OSC V and you can see that the dashed line V1 is moving up and down while the measured voltage value of V1 relative to the zero position of CH1 appears on the screen 02 2010 Page 40 users manuan oszse 6 Press and hold the OSC OPTION key till A Y CURSOR V2 appears on the screen Now adjust the OSC A or OSC Y and you can observe the dashed line V2 moving up and down while the measured voltage value of V2 relative to the zero position of CH1 is displayed on the screen Also the absolute values of V1 and V2 can be shown on the screen f 51 2 SU Figure 24 Use the cursor for a voltage measurement To use the cursor for a time measurement on CH1 do the following Page 41 Press the MENU key and the function menus are displayed at the right of the Screen Press the MENU A or MENU key to sel
88. pecificados a fin de preservar la seguridad Alimentador DC externo Puntas de prueba Multimetro Sondas de medida Osciloscopio El negativo de medida como Osciloscopio es com n al potencial negativo del conector de entrada salida de datos El negativo de medida de los canales del osciloscopio es com n Al efectuar medidas desconectar los cables que no se utilicen Revise el estado de las puntas de prueba antes de la utilizaci n Tener siempre en cuenta los m rgenes especificados tanto para alimentaci n como para medida Recuerde que las tensiones superiores a 70 V DC o 33 V AC rms son potencialmente peligrosas Observar en todo momento las condiciones ambientales m ximas especificadas para el aparato El operador no est autorizado a intervenir en el interior del equipo Cualquier cambio en el equipo deber ser efectuado exclusivamente por personal especializado No impedir la ventilaci n del equipo Seguir estrictamente las recomendaciones de limpieza que se describen en el apartado Mantenimiento P gina 7 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX S mbolos relacionados con la seguridad CORRIENTE CONTINUA MARCHA CORRIENTE ALTERNA PARO ALTERNA Y CONTINUA DOBLE AISLAMIENTO Protecci n CLASE ll PRECAUCI N Riesgo de choque el ctrico TERMINAL DE TIERRA TERMINAL DE PROTECCI N PRECAUCI N VER MANUAL TERMINAL A CARCASA FUSIBLE EQUIPOTENCIALIDAD
89. r running or stopping the operation MENU Y Choose the lower item on the menu list MENU Show Hide the menu MENU A Choose the upper item on the menu list F1 F5 Switch or Adjust options for each menu BCN input connectors for oscilloscope channels CH1 and CH2 Multimeter input terminals Three terminals banana type Ma A COM V O C and two socket terminals for capacitance measurement Probe compensation output Test signal of 5 Vpp and 1 kHz frequency Page 12 users manuan osz APRAX 4 USING THE OSCILLOSCOPE 4 1 Power Up the oscilloscope Connect oscilloscope to AC power via a power adapter as shown in Figure 1 The oscilloscope may still work with built in Li ion battery even without AC power supply Turn the oscilloscope on by pressing down the power on off key E The instrument then performs Selfchecking after power on A greeting window and a sentence press any key to continue will display on the screen when the system finishes selfchecking The users can press any key to enter the measuring function The oscilloscope is powered up in its last setup configuration 4 2 Charging the oscilloscope The lithium battery is possibly not charged when delivery To make the battery with enough electric quantity it must be charged for 4 hours the test tool must be turned off during charging The battery can supply power for 4 hours after being charged completely When supplying power by using the bat
90. re 37 Capacitance measurement Page 53 02 2010 users manuan oszse O 5 4 5 Making a DC voltage Measurement VDC To measure a DC voltage do the following Press the V key and DCV appears at the top of the screen Insert the black lead into the COM banana jack input and the red lead into the V Q banana jack input Connect the red and black leads to the measured point and the measured point voltage value is displayed on the screen Now you can see a screen that looks like the following Figure 38 Figure 38 DC voltage Measurement 5 4 6 Making a AC voltage Measurement VAC To measure the AC voltage do the following 02 2010 Press the V key and DCV appears at the top of the screen Press the AUTO SET key and ACV appears at the top of the screen Insert the black lead into the COM banana jack input and the red lead into the V Q banana jack input Connect the red and black leads to the measured points and the AC voltage values of measured points will be displayed on the screen Page 54 users manuan oszse Figure 39 AC voltage Measurement 5 4 7 Making a DC current Measurement AAC In order to carry out the measurement of current it is necessary to connect in series the meter and the circuit under test Make sure that the circuit is disconnected before doing this connection To measure a DC current which is less than 400 mA do the following 1 Press the A
91. reen centerline It reads zero when the pointer is in the center of the screen 6 The trigger state indicates the following information Auto The oscilloscope is working in the automatic mode and displaying the waveform under the non trigger state Trig d The oscilloscope has detected a trigger and collecting the information generated after the trigger Ready All pre triggered data have been captured and the oscilloscope has been ready to receive trigger signals Scan The oscilloscope can gather and display the waveform data continuously in scanning mode Stop The oscilloscope has stopped collecting the waveform data 7 The green pointer shows the trigger voltage level 8 Oscilloscope main menu Pressing the MENU button this menu will be visualised hide 9 Menu setting options There are different setting options for different menus 10 It reads the value of trigger voltage level 11 The display shows the trigger signal source 12 The reading gives the value of primary time base 13 These graphics present the coupling modes of channel CH2 The graphic indicates AC the graphic indicates DC 14 It shows the vertical V div value for channel CH2 15 These graphics show the coupling mode of CH1 among which the graphic express indicates AC the graphic indicates DC 16 It shows the vertical V div value for channel CH1 17 The blue indicator shows the CH2 zero position If channe
92. ress the MENU A or MENU W key to select MATH and 5 options are displayed at the bottom of the screen 3 Press the F8 CH1 CH2 key and the obtained waveform M appears on the screen Again press the F3 key and Close the waveform M 4 Press the OSD OPTION key and the following is displayed on the screen lt gt Time Base A V CH1 Vol 5 Press the OSC A or OSC W key to adjust the amplitude of the waveform M 02 2010 Page 26 users manuan os7ee O O oO o 6 Again press the OSD OPTION key twice and the screen shows the following lt gt Time A V CHM Zero 7 Press the OSC A or OSC W key to adjust the position of the waveform Math Now look at the display and you will find a screen that looks like the following Figure 15 Up 601 6nu Figure 15 Waveform mathematics 4 13 Setting the Trigger System TRIGGER Function The Trigger defines the time when the acquisition of data and display of waveform start If it is set correctly the trigger can turn an unstable display into a significant waveform When starting the acquisition of data the oscilloscope collects sufficient data to draw the waveform at the left side of the triggering point With waiting for the triggering condition the oscilloscope is gathering data continuously After a trigger is detected the oscilloscope gathers enough data continuously to draw the waveform at the right side of the
93. riba y abajo pulsando OSC OPTION y modificado el par metro CH Math Cero Tabla de operaciones matem ticas Ajuste Descripci n CH1 CH2 Forma de onda de CH1 menos forma de onda de CH2 CH2 CH1 Forma de onda de CH2 menos forma de onda de CH1 CH1 CH2 Forma de onda de CH1 mas forma de onda de CH2 CH1 CH2 Forma de onda de CH1 multiplicada por forma de onda de CH2 CH1 CH2 Forma de onda de CH1 dividida entre forma de onda de CH2 Para realizar el c lculo de forma de onda 1 2 haga lo siguiente 1 Pulse la tecla MENU y el Men de Funciones aparecer a la derecha de la pantalla 2 Pulse las teclas MENU A o MENU Y para seleccionar MATH Cinco opciones aparecer n en la zona inferior de la pantalla 3 Pulse la tecla F3 CH1 CH2 y la forma de onda obtenida aparecer en pantalla de color verde Pulse de nuevo F3 para desactivar la forma de onda calculada 02 2010 P gina 24 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 4 Pulse la tecla OSC OPTION el siguiente texto aparecera en pantalla lt gt Time Base A Y CHMath Volts div 5 Pulse las teclas OSC A o OSC para ajustar la amplitud de la forma de onda MATH 6 Pulsela tecla OSC OPTION y el siguiente texto aparecer en pantalla lt gt Tiempo A Y CHMATH Cero 7 Pulse las teclas OSC 6 OSC W para ajustar la posici n de la forma de onda MATH Ver Figura 15 Up 601 6nu Figura
94. s de modo Vectores y Puntos como se puede ver en las Figuras 20 y 21 P gina 31 02 2010 MANUAL DE INSTRUCCIONES OS 782 ZXPROMAX f SOHZ riesen ieee Figura 21 Modo de vector 4 16 2 Persistencia Seleccionando la funci n Persistencia los datos originales mostrados pierden gradualmente color mientras que los nuevos datos aparecen en pantalla en colores m s brillantes con el modo Persistencia Infinita seleccionado los puntos registrados se mantendr n en pantalla hasta que el valor establecido cambie 4 16 3 Modo XY Este modo s lo es aplicable con los canales CH1 y CH2 activados Con el modo XY seleccionado CH1 se muestra en el eje horizontal y CH2 en el eje vertical Cuando el osciloscopio est en modo de muestreo en el que no hay ning n disparo los datos aparecen en puntos m s claros 02 2010 P gina 32 AxPROMAX Funciones OSC OPTION MANUAL DE INSTRUCCIONES OS 782 Las funciones CH1 Volts div y CH1 Cero para CH1 se utilizan para fijar la posici n y la escala horizontales Las funciones CH2 Volts div y CH2 Cero para CH2 se utilizan para fijar la posici n y la escala verticales Las siguientes funciones no son operativas en el modo de visualizaci n de XY Forma de onda de referencia o de valor digital Cursor Ajuste autom tico Control de bases de tiempo Control de disparo 4 17 Ajustes para guardar las formas de onda Funci n MEMORIA El osciloscopi
95. siguiente tabla Par metros Configuraciones Descripci n Principal La principal base de tiempo horizontal se usa para la visualizaci n de ondas Ventana Usa dos cursores para definir un rea de ventana Zoom Ampl a la ventana definida a la visualizaci n de ventana pantalla completa Para realizar una ampliaci n de ventana siga los pasos siguientes 1 Pulse la tecla MENU y el Men de Funciones aparecer a la derecha de la pantalla 2 Pulse las teclas MENU A o MENU Y para seleccionar HORIZONTAL Tres opciones aparecer n en la zona inferior de la pantalla 3 Pulse tecla F3 para seleccionar Ventana 4 Pulse la tecla OSC OPTION seleccione Time Base y pulse OSC A OSC para ajustar el area de la ventana de base de tiempos definida por los dos cursores El tama o de ventana cambiar 5 Pulse la tecla OSC OPTION seleccione Tiempo y pulse OSC A OSC Y para ajustar la posici n de la ventana definida por los dos cursores La posici n de la ventana es la diferencia de tiempo del centro de la ventana al indicador horizontal de la base de tiempo principal 6 Pulse la tecla F2 para seleccionar Zoom Ventana y la ventana definida aumentar a modo de pantalla completa Ver Figuras 31 y 32 02 2010 P gina 44 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 UP DOWN CHi Vol Up 3 240u U 1 449u Figura 32 Extensi n de ventana 4 24 Transmisi n de datos al PC El osciloscop
96. t obstruct the ventilation system Follow the cleaning instructions described in the Maintenance paragraph Page 7 02 2010 users manuan osz APRAX Symbols related with safety DIRECT CURRENT ALTERNATING CURRENT DIRECT AND ALTERNATING GROUND TERMINAL PROTECTIVE CONDUCTOR FRAME TERMINAL EQUIPOTENTIALITY ON Supply OFF Supply DOUBLE INSULATION Class II Protection CAUTION Risk of electric shock CAUTION REFER TO MANUAL l gt gt _ 4 Orde FUSE 02 2010 Page 8 USER S MANUAL OS 782 2 2 Descriptive Examples of Over Voltage Categories Cat Cat Il Cat Ill Cat IV Page 9 Low voltage installations isolated from the mains Portable domestic installations Fixed domestic installations Industrial installations AXPROMAX 02 2010 users manuan osz APRAX 02 2010 Page 10 usersmanuaos7ee O APRA 3 DESCRIPTION FOR FRONT PANEL AND KEYS See the following Figure 1 Figure 1 Front Pannel Description 1 Power adapter jack 2 USB port 3 Backlight switch 4 QO Power switch 5 A Multimeter current measurement key Page 11 02 2010 users manuan osz APRAX 2a 2 2 No 11 12 13 14 15 16 17 18 19 20 21 22 02 2010 V Multimeter voltage measurement key R Multimeter resistance triode On Off and capacitance measurement key OSC lt Oscilloscope left direction adjustment key OSC P Oscilloscope right directi
97. tery a battery indicator is displayed on the top of the screen to show the consumption condition of electric quantity The symbols that are possibly appear include a E El and where 0 shows that the battery can only be used for about 5 minutes To charge the battery and power the instrument connect the oscilloscope using a power adapter according to Figure 1 to charge the battery The charging speed can be increased by turning off the test tool To avoid superheat of battery during charging the environment temperature is not allowed to exceed the permissible value given in technical specification whole weekend The instrument can automatically switch to slowly charging status NOTE No hazard will occur even connecting the charger for a long time e g during a Page 13 02 2010 users manuan oszee 4 3 Oscilloscope Operation Window See the following figure 2 Figure 2 Oscilloscope Operation Window Description 1 Battery electric quantity indicating symbols including a E a y fl 2 3 Measurement indicators 1 and 2 Diverse parameters can be shown Frequency f peak value Up V average value etc Two parameters from one channel or one parameter from each channel can be shown 4 The pointer indicates the horizontal triggering position 02 2010 Page 14 users manuan osz APRAX 5 This reading gives the Time Difference between the horizontal triggering position and the sc
98. tive probe Probe attenuation factor Corresponding Menu Setting Table Probe attenuation factor and the corresponding menu setting Page 25 02 2010 usersmanuaoszee LAR PROMAXX 4 11 4 Setting of Inverted Waveform Inverted waveform The displayed signal reverses 180 degrees relatively to the ground potential Press F4 Invert to start Invert again press F4 Invert to close Invert 4 12 MATH function MATH The MATH functions in showing the result of adding subtracting multiplying or dividing calculation on CH1 and CH2 channel waveforms Also the result of arithmetic operation can be measured with grid or cursor The amplitude of the calculated waveform can be adjusted with CHM VOL which is displayed in the scale factor form The amplitude ranges from 0 001 through 10 and steps in the 1 2 5 form that is it can be expressed as 0 001X 0 002X 0 005X 10X The position of the calculated waveform can be adjusted up and down with the CHM ZORE key used The corresponding operation function table Setting Description CH1 CH2 CH1 waveform minus CH2 waveform CH2 CH1 CH1 waveform minus CH2 waveform CH1 CH2 Add CH1 waveform into CH2 waveform CH1 CH2 Multiply CH1 waveform and CH2 waveform CH1 CH2 Divide CH1 waveform by CH2 waveform To perform the CH1 CH2 waveform calculation do the following 1 Press the MENU key and the function menu appears at the right of the screen 2 P
99. tom ticas tales como frecuencia periodo valor promedio valor de pico a pico valor eficaz valor m ximo etc Y da dos clases de resultados de medida simult neamente en la pantalla El men de Medidas autom ticas se describe en la siguiente tabla Par metros Configuraciones Descripci n Freq CH1 Medida frecuencia de CH1 CH2 Medida frecuencia de CH2 Periodo CH1 Medida del per odo de CH1 CH2 Medida del per odo de CH2 Promedio CH1 Medida del valor promedio de CH1 Vavg CH2 Medida del valor promedio de CH2 Pico Pico CH1 Medida del valor pico a pico de CH1 Vpp CH2 Medida del valor pico a pico de CH2 V eficaz CH1 Medida del valor eficaz de CH1 Vrms CH2 Medida del valor eficaz de CH2 Vm x CH1 Medida del valor m ximo de CH1 CH2 Medida del valor m ximo de CH2 Vmin CH1 Medida del valor minimo de CH1 CH2 Medida del valor minimo de CH2 Vtop CH1 Medida del valor de pico de CH1 CH2 Medida del valor de pico de CH2 Vbase CH1 Medida del valor de base de CH1 CH2 Medida del valor de base de CH2 Pagina 35 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX Par metros Configuraciones Descripci n CH1 Medida de la amplitud de CH1 CH2 Medida de la amplitud de CH2 CH1 Medida del valor de exceso de CH1 CH2 Medida del valor de overshoot de CH2 CH1 Medida del valor de defecto de CH1 CH2 Medida del valor de presto de CH2 Tiempo CH1 Medida del tiempo de subida de CH1
100. triggering point To make a trigger mode setting do the following 1 Press the MENU key and the function menu appears at the right of the screen 2 Press the MENU or MENU W key to select TRIG MODE and five items selectable are displayed at the bottom of the screen Page 27 02 2010 users manuan os7ee oO o 3 Select and press one from F1 through F5 key to make a different setting 4 Press the OSD OPTION key and the following is shown on the screen lt gt Time A V Trig 5 Press the OSC A or OSC V key to adjust the trigger level position Now look at the display you can see a screen in the following figure 16 f 1 005KHZ f 1 005KHZ Figure 16 Edge triggering 4 14 Triggering Control There are two triggering modes including Edge triggering and Video triggering Each trigger mode is set by different function menu Edge triggering It occurs when the trigger input passes through a given level along the specified direction Video triggering Perform video field trigger or line trigger on the standard video signals 02 2010 Page 28 USER S MANUAL OS 782 4 14 1 Edge triggering AXPROMAX The Edge triggering menu is described in the following table Function menu Settings Description Slope Rise Fall Triggering on the rise edge of the signal Triggering on the fall edge of the signal Signal source CH1 CH2 C
101. ubida t pico de BNC Precisi n de ganancia DC Precisi n de medida DC modo de muestreo de valor promedio DISPARO Sensibilidad de disparo disparo por flanco Acoplamiento DC Acoplamiento AC Rango de nivel de disparo Precisi n del nivel de disparo t pica aplicable a la se al con el tiempo de subida y bajada igual o mayor que 20 ns Desplazamiento del disparo Margen de tiempo de bloqueo de disparo Ajuste del 50 del nivel t pico P gina 3 MANUAL DE INSTRUCCIONES OS 782 Disparo nico 1 intervalo de muestreo 100 ppm de lectura 0 6 ns gt 16 promedios 1 intervalo de muestreo 100 ppm de lectura 0 4 ns Resoluci n de 8 bits muestreando ambos canales sincronizadamente 5 mV div 5 V div en BNC de entrada 50 V 500 mV 5 V 2 V 5 mV 200 mV 20 M Ancho de banda completo gt 5 Hz en BNO lt 17 5 ns 5 96 Diferencia de voltaje AV entre dos puntos de la se al despu s de una adquisici n promediada con factor 16 5 reading 0 05 divisions CH1 y CH2 1div DC ancho de banda completo Igual a los l mites de acoplamiento DC para frecuencias superiores a 50 Hz 6 divisiones desde la l nea central de la pantalla 0 3 divisiones 655 divisiones para predisparo y 4 divisiones para pos disparo 100 ns 10 s Operaci n con la frecuencia de se al de entrada igual o mayor que 50 Hz 02 2010 MANUAL DE INSTRUCCIONES OS 782 Sensibili
102. ustment The defaulted range mode of the instrument is automatic range To switch to the manual range perform the following steps 1 Press F1 key and MANUAL is displayed on the top left side of the screen to enter the manual range mode 2 Under the manual range mode the measuring range is increased by a stage when pressing F1 key each time and when reaching the highest stage it jumps to the lowest stage by pressing F1 key once again To multiply the reading of dial pointer by multiplying power and the unit of main reading on the screen will get the measurement result 3 Press F3 key and AUTO is displayed on the top left side of the screen to switch back to the automatic range mode Look at the display you can see a screen that looks like the following figure 46 Figure 46 Automatic manual range adjustment ATTENTION Capacitance measurement without manual range mode 02 2010 Page 60 users manuan osz LAR PROMAXX 6 TROUBLE SHOOTING 1 The oscilloscope does not power up It may be caused by the dead battery At this time the oscilloscope will not start even if it is powered by the battery charger Firstly charge the battery and supply the oscilloscope with power through the battery charger However don t switch on the oscilloscope till waiting for 15 minutes If the oscilloscope still cannot start please contact PROMAX for service 2 The oscilloscope stops work only after operating for several seconds Probably
103. ut CH2 See the following figure 10 NOTE When pressing the F1 F5 keys the measured channel CH1 CH2 changes alternatively f 1 17 2 Up 632 Figure 10 Automatic scope measurements 4 10 Freezing the Screen You can freeze the screen all readings and waveforms 1 Press the RUN STOP key to freeze the screen and STOP appears at top right side of the screen 2 Press the RUN STOP key once more to resume your measurement See the following figure 11 02 2010 Page 22 users manuan oszee f 1 117KHZ CH2 OFF CH1 0 04 dius 2 0nu LEFT RIGHT Time Base Figure 11 Freezing the screen 4 11 Setting the Vertical CH1 and CH2 Each channel has its own independent vertical menu and each item can be set respectively based on the specific channel Open the vertical menu of functions and select to CHANNEL 1 or CHANNEL 2 functions The parameters to be modified with F1 F5 keys appear in the lower part of the display Figure 12 Setting the Vertical CH1 and CH2 Page 23 02 2010 users manuan oszse O O O Oo o The following Table describes the Vertical Channel menu Function menu Coupling The DC component in the input signal is blocked The AC and dc components of the input signal are allowed Setting Description Channel Close the channel Open a channel Probe Select one according the probe attenuation factor to ensure a corre
104. xtremo de los cables rojo y negro al diodo que desea medir La lectura del valor del diodo se mostrar en la pantalla en V Ver Figura 35 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX Figura 35 Medida de diodo 5 4 3 Prueba continuidad Para hacer una prueba de continuidad haga lo siguiente 1 Pulse la tecla R y el s mbolo R aparecer en la parte superior de la pantalla 2 Pulse repetidamente la tecla AUTO SET hasta que el siguiente s mbolo aparezca en pantalla al 3 Inserte el cable negro en la entrada COM tipo banana y el cable rojo en el la entrada V tipo banana 4 Conecte el otro extremo de los cables rojo y negro al punto de prueba Si el valor de la resistencia del punto de prueba es menor de 50 Q el multimetro emitira un pitido Ver Figura 36 Figura 36 Prueba de funcionamiento 02 2010 Pagina 50 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 5 4 4 Medici n de una Capacitancia Para medir una capacitancia haga lo siguiente 1 Pulse la tecla R y el s mbolo R aparecer en la parte superior de la pantalla 2 Pulse repetidamente la tecla AUTO SET hasta que el s mbolo C aparezca en la zona superior de la pantalla 3 Inserte la capacitancia en la entrada cuadrangular use las puntas de prueba conectadas a los terminales COM y V Q y la pantalla mostrara la lectura de la capacitancia NOTA Cuando el valor de la capacitancia es menor de 5 nF por favor use el
105. y and the function menu appears on the right side of the screen 2 Press the MENU A or MENU W key to select function setting and three options are visible at the bottom of the screen 3 Press F1 RESET key to select the factory settings The oscilloscope is set to be the factory settings See the following figure 9 Figure 9 Reset the Oscilloscope 4 7 Displaying an Unknown Signal with Auto Set The Auto Set feature lets the Oscilloscope display and measure unknown signals automatically This function optimizes the position range time base and triggering and assures a Stable display of virtually any waveform This feature is especially useful for quickly checking several signals 02 2010 Page 20 users manua osz LAR PROMAXX To enable the Auto Set feature do the following 1 Connect the test probe to the tested signals 2 Press the AUTO SET key and the Oscilloscope is under the automatic measurement condition The tested signals appear on the screen 4 8 Automatic zero returning of trigger horizontal position and trigger level position When we adjust the trigger horizontal position and trigger level position to be maximal to make it off the screen center remotely then we perform the following steps to make trigger horizontal position and trigger level position return to zero automatically 1 Press OSC 4 and OSC gt key simultaneously the trigger horizontal position automat
106. y realizar una medida de Pico Pico La ventana de Medida 2 se vuelve azul y muestra el valor pico pico para la entrada del CH2 Ver Figura 10 Con cada pulsaci n de las teclas F1 F5 cambia alternativamente el canal medido CH1 CH2 f 1 170KHZ Up 632 Figura 10 Medidas autom ticas del osciloscopio 4 10 Congelaci n de la imagen en pantalla La imagen en pantalla se puede congelar con todas las lecturas y formas de onda Para ello siga los siguientes pasos 1 02 2010 Pulse la tecla RUN STOP para congelar la pantalla La palabra STOP aparece en esquina superior derecha de la pantalla Pulse la tecla RUN STOP una vez m s para reanudar su medida Ver Figura 11 P gina 20 AxPROMAX MANUAL DE INSTRUCCIONES OS 782 f 1 117KH2 CH2 OFF Figura 11 Congelaci n de la pantalla 4 41 Ajuste del eje vertical de CH1 y CH2 Funci n CANAL 1 CANAL 2 Cada canal tiene su propio ment vertical independiente y los distintos par metros se pueden ajustar para cada canal de forma independiente Abra el ment vertical de funciones y seleccione la funci n CANAL1 6 CANAL 2 Los par metros configurables con las teclas F1 F5 aparecen en la parte inferior de la pantalla Figura 12 Ajustes de los ejes verticales de CH1 o CH2 P gina 21 02 2010 MANUAL DE INSTRUCCIONES OS 782 AXxPROMAX La siguiente tabla describe el men de ajustes de los ejes verticales del canal Men S A

Download Pdf Manuals

image

Related Search

Related Contents

di tutto il volume  Fisher & Paykel AU SG User's Manual  Cisco 802.11g IOS AP w/Avail CBus Slot Japan  version_imprimable-3 ( PDF  Avaya 4600 Series IP Telephones Application Note  Kenmore 36'' Sealed Gas Cooktop 3243 Installation Guide  The Auto-fiction in the Work of Colette  Certificats Electroniques sur Clé USB  Aiwa FR-A305 Clock Radio  本文 - 厚生労働省  

Copyright © All rights reserved.
Failed to retrieve file