WR series / User`s Manual - DAS Audio
Contents
1. WR 6412 Four WR 6412 8 ohms each in parallel per channel Refer to the user manual of the D 100 amplifier for SPEAKON connection 12 Manual del Usuario WR series User s Manual INSTALLATION INSTRUCTIONS Warnings This manual contains needed information for flying D A S Audio systems description of the elements and safety precautions To perform any operations related to flying the system read the present document first and act on the warnings and advice given The goal is to the allow the user to become familiar with the mechanical elements required to fly the acoustic system as well as the safety measures to be taken during set up and teardown Only experienced installers with adequate knowledge of the equipment and local safety regulations should fly speaker boxes lt is the user s responsibility to ensure that the systems to be flown including flying accessories comply with state and local regulations The working load limits in this manual are the results of tests by independent laboratories It is the user s responsibility to stay within safe limits It is the user s responsibility to follow and comply with safety factors resistance values periodical supervisi2. 122505 DSP 2040 le 020 D20 Four WR 8826 16ohms each in parallel mode per channel Refer to the user manual of the D 20 amplifier for SPEAKON connection Manual del Usuario WR series User s Manual 16 x WR 8826 2100W 2 Ohms Eight WR 8826 16ohms each in parallel per channel Refer to the user manual of the D 20 amplifier for SPEAKON connection 4 x WR 6412 or WR 6415 1150W O 4 Ohms
3. D SP 2040 D 20 Two WR 6412 8 ohms each in parallel per channel Refer to the user manual of the D 20 amplifier for SPEAKON connection Manual del Usuario WR series User s Manual 11 8 x WR 6412 or WR 6415 2100W 2 Ohms WR 6415 WR 6415 Four WR 6415 8 ohms each in parallel per channel Refer to the user manual of the D 20 amplifier for SPEAKON connection 16 x WR 6412 or WR 6415 3700W 2 Ohms WR 6412
4. Manual del Usuario WR series User s Manual 16 TROUBLESHOOTING PROBLEM 1 No sound from any units 2 sound from one unit 3 Poor stereo image or weak bass output Manual del Usuario WR series User s Manual SOLUTION 1 1 1 Check that the amplifier is on 1 1 2 Check that the gain is set above its minimum setting 1 1 3 Check that there is a signal to your amplifier from your mixer 1 2 1 Check that the cable from the sound source to the UNIT is connected correctly Replace the cable if defective 1 2 2 Check that none of the connected cables are cut or frayed 1 3 1 Check the minimum impedance requirements of your amplifier 2 1 1 Check that the cable between the UNITS is connected correctly Replace the cable if defective 2 1 2 Check the balance control on the mixer 3 1 1 Check the polarities and be sure that all the speakers are well connected 17 Si a
5. Armonizadas Europeas In accordance with Harmonized European Norms e 60065 2002 A1 2006 A11 2008 A2 2010 A12 2011 Audio video and similar electronic apparatus Safety requirements e 54 24 2008 Fire detection and fire alarm systems Part 24 Components of voice alarm systems Loudspeakers Manual del Usuario WR series User s Manual SYSTEM DESCRIPTION Introduction The WR Weather Resistant series is a series of products aimed at the outdoor installation market This series is EN 54 certified according to the EN 54 24 2008 standard Fire detection and fire alarm systems Part 24 Components of voice alarm systems Loudspeakers This series is composed of 3 base models WR 8826 a dual 6 two way WR 6412 12 two way WR 6415 a 15 two way Each of these models will be offered in two exposure ratings covered exposure for applications where cabinets are covered or protected DX direct exposure where cabinets are unprotected and directly exposed to the environment The CX versions are protected with a thick exterior Iso Flex paint coating The DX versions augment the protection rating by employing a supplementary fiberglass exterior finish Stainless steel fittings and mounting hardware are offered for both versions The WR 8826 models are equipped with the M 1 driver employing a 1 annular diaphragm and an 80 x 80 horn geometry The WR 6412 and WR 6415 models
6. IN MILIMETERS Bottom View Front View Bottom View Bottom View Front View Right View Rear View Right View Rear View Right View Rear View CONNECTION The WR series includes protection methods to ensure the best connectivity conditions even under harsh weather conditions It includes a waterproof cover which gives us a double connection chamber Don t remove after installation After the installation is finished don t remove any safety parts in normal working conditions Security operations and or technical services should be performed by authorised staff The system includes 5m of connection wire ready to use in the application The color code is Blue gt e BW ead To obtain a better performance and achieve the best optimization of the system parameters DAS AUDIO recommends using the WR cabinets with amplifier models D 20 or D 100 and the DSP2040 processor as shown in the configurations in this manual For assembling SPEAKON connectors follow the amplifiers user manual for the correct connection Manual del Usuario WR series User s Manual The system includes 5m of connection wire
7. User s Manual CONTENTS SAFETY PRECAUTIONS 3 WARRANTY 4 DECLARATION OF CONFORMITY 5 SYSTEM DESCRIPTION 6 LINE DRAWINGS 7 CONNECTION serenus 7 8 SPECIFICATIONS suu 9 CONFIGURATIONS d 10 12 4 x WR 8826 625W 8 Ohms 8 x WR 8826 1150W 4 Ohms 16 x WR 8826 2100W 2 Ohms 4 x WR 6412 or WR 6415 1150W 4 Ohms 8 x WR 6412 or WR 6415 2100W 2 Ohms 16 x WR 6412 or WR 6415 3700W 2 Ohms INSTALLATION INSTRUCTIONS 13 16 TROUBLESHOOTING 17 Manual del Usuario WR series User s Manual WR series Cajas ac sticas pasivas Passive loudspeaker enclosures Conserve y lea todas estas instrucciones Siga todas las advertencias El signo de exclamaci n dentro de un tri ngulo indica la existencia de componentes internos cuyo reemplazo puede afectar a la seguridad El doble cuadrado indica equipo de Clase II Las especificaciones se encuentran en la etiqueta de la parte posterior del producto El colgado del equipo s lo debe realizarse utilizando los herrajes de colgado recomendados y por personal cualificado Equipo IP 56 seg n la norma IEC 60529 1989 M1 1999 con un ngulo horizontal m nimo de 2 Este s mbolo indica que el presente producto no puede ser tratado como residuo dom stico normal sino que debe entregarse en el correspondiente punto de recogida de equipos el ctricos y electr nicos Equipo dise ado para funcionar entre 25 y 70 L
8. a humedad relativa m xima del 95 con 40 C de temperatura ambiente El cableado exterior conectado al equipo requiere de su instalaci n por una persona instruida o el uso de cables flexibles ya preparados El equipo cuenta con dos conectores de entrada en paralelo para facilitar la conexi n de varias cajas en paralelo No emplace altavoces en proximidad a equipos sensibles a campos magn ticos tales como monitores de televisi n material magn tico de almacenamiento de datos No existen partes ajustables por el usuario en el interior de este equipo Cualquier operaci n de mantenimiento o reparaci n debe ser realizada por personal cualificado Es necesario el servicio t cnico cuando el aparato se haya da ado de alguna forma tal como que haya ca do l quido o alg n objeto en el interior del aparato haya sido expuesto a lluvia o humedad no funcione correctamente o haya recibido un golpe Limpie con un pafio seco No use limpiadores con disolventes Keep these instructions Heed all warnings Follow all instructions The exclamation point inside an equilateral triangle indicates the existence of internal components whose substitution may affect safety The double square indicates Class device The specifications can be found on the rear label of the product The appliance should be flown only from the rigging points and by qualified personnel IP 56 equipment IEC 60529 1989 M1 1999 Minimum horizonta
9. afety When flying enclosures from ceiling support structures extreme should be taken to assure the load bearing capabilities of the structures so that the installation is absolutely safe Do not fly enclosures from unsafe structures Consult a certified professional if needed All flying accessories that are not supplied by D A S Audio are the user s responsibility Use at your own risk Periodicaly check the system replacing the estructural elements which could be deteriorated Introduction The WR system includes a double connection chamber to achieve better connectivity conditions even under harsh weather conditions The minimum angle in the horizontal plane to ensure the max IP ratio IP56 is 2 Manual del Usuario WR series User s Manual 18 Flying with eyebolts The WR series models feature internal steel flying points with mounting threads These eyebolt flying points are factory sealed with M10 screws which are replaced with eyebolts on the flying points as required Flying with eyebolts is very economical and safe and is specially recommended for fixed installations where the boxes are permanently fixed The Allen head screws must be removed and replaced by M10 eyebolts on one side of the enclosure Each rigging point has a 200 kg 440 Ib working load limit Then choose the slings or chains of required load resistance and length bearing in mind that the length difference between the front and back
10. function of the f load angle Y s Em gt cy Manual del Usuario WR series User s Manual 14 Rigging accessories AXU WR8826 AXU WR6412 AXU WR6415 The AXU WR8826 AXU WR6412 AXU WR6415 are not included with the WR 8826 WR 6412 and WR 6415 respectively in the packaging The AXU accessories have been designed to enable mounting the speakers in a horizontal and vertical position They can also be installed on walls or ceilings Mounting instructions 1 Remove the top and bottom screws from the speaker cabinet 2 Position the AXU WRXXXX on the wall or ceiling 3 Position the WR cabinet between the arms of the support Beware that the AXU support allows for an asymmetric arc Install in the appropriate position 4 Attach the unit to the support using the screws step 1 but do not tighten 5 Aim the unit to the desired angle and tighten screws Manual del Usuario WR series User s Manual 15 Description of the AXU WR8826 AXU WR6412 AXU WR6415 Refer to the user s manual of accessories on our website for more information AXC AT for use in combination with two AXC AT free use EF N o lt free use for mounting on wall or ceiling Safety point 2 Safety point or from 45 to 90
11. l angle 2 This symbol on the product indicates that this product should not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Working temperature ranges from 25 C to 70 The maximum relative humidity of 95 with ambient temperature 40 The outer wiring connected to the device requires installation by an instructed person or the use of a flexible cable already prepared Note that the two input connectors are wired in parallel to provide easy parallel connection of several enclosures Do not place loudspeakers in proximity to devices sensitive to magnetic fields such as television monitors or data storage magnetic material No user serviceable parts inside Refer all servicing to qualified Service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Clean only with a dry cloth Do not use any solvent based cleaners Manual del Usuario WR series User s Manual 3 GARANTIA Todos nuestros productos est n garantizados por un periodo de 24 meses desde la fecha de compra Las garant as s lo ser n v lidas si son por un defecto de fabricaci n y en ning n caso por un uso inc
12. nce Grille Connector Dimensions H x W x D Net weight Optional Accessories Nominal Power based on a 100h test using a 6dB crest factor pink noise signal filtered according to the IEC 60268 1 1985 norm and band pass filtered with Butterworth 24dB Oct filters from 89Hz to 11 2kHz SSensitivity and Max SPL measured using a 6dB crest factor pink noise averaged from 100Hz to 10kHz in 1 3 Octave bands coverage measured from 500Hz to 4kHz in Octave bands Based on a 2 hour test using a 6dB crest factor pink noise signal Conventionally 3dB higher than the RMS measure although this already utilizes a program signal Corresponds to the signal crests for the test described in Obtain from a time window of a 30 seconds Impedance of a frequency range of 20 Hz 2 kHz for better optimization of amplifiaction devices CONFIGURATIONS 4 x WR 8826 625W 9 8 Ohms DSP 2040 erm E D 20 Two WR 8826 16ohms each in parallel mode per channel Refer to the user manual of the D 20 amplifier for SPEAKON connection 8 x WR 8826 1150W 4 Ohms
13. ons and warnings given in this manual Product improvement by means of research and development is on going at D A S Specifications are subject to change without notice To this date there is no international standard regarding the flying of acoustic systems However it is common practice to apply 5 1 safety factors for enclosures and static elements For slings and elements exposed to material fatigue due to friction and load variation the following ratios must be met 5 1 for steel cable slings 4 1 for steel chain slings and 7 1 polyester slings Thus an element with a breaking load limit of 1000 kg may be statically loaded with 200 kg 5 1 safety factor and dynamically loaded with 142 kg 7 1 safety factor When flying a system the working load must be lower than the resistance of each individual flying point in the enclosure as well as each box Hanging hardware should be regularly inspected and suspect units replaced if in doubt This is important to avoid injury and absolutely no risks should be taken in this respect lt is highly recommended that you implement an inspection and maintenance program on flying elements including reports to be filled out by the personnel that will carry out the inspections Local regulations may exist that in case of accident may require you to present evidence of inspection reports and corrective actions after defects were found Absolutely no risks should be taken with regards to public s
14. orrecto del producto Las reparaciones en garant a pueden ser realizadas exclusivamente por el fabricante o el servicio de asistencia t cnica autorizado Otros cargos como portes y seguros son a cargo del comprador en todos los casos Para solicitar reparaci n en garant a es imprescindible que el producto no haya sido previamente manipulado e incluir una fotocopia de la factura de compra WARRANTY All D A S products are warrantied against any manufacturing defect for a period of 2 years from date of purchase The warranty excludes damage from incorrect use of the product All warranty repairs must be exclusively undertaken by the factory or any of its authorised service centers To claim a warranty repair do not open or intend to repair the product Return the damaged unit at shippers risk and freight prepaid to the nearest service center with a copy of the purchase invoice Manual del Usuario WR series User s Manual DECLARACI N DE CONFORMIDAD DECLARATION OF CONFORMITY D A S Audio S A C Islas Baleares 24 46988 Pol Fuente del Jarro Valencia Espafia Spain Declara que la serie WR Declares that WR series Cumple con los objetivos esenciales de las Directivas Abide by essential objectives relating Directives e Low Voltage Directive 2006 95 EC e Regulation EU No 305 2011 Constrution Products Certificate of Constancy of Performance 0359 CPR 00429 Y es conforme a las siguientes Normas
15. ready to use in the application If more than 5m of connection wire is required a longer cable can be used If so proceed as follows 1 Prepare the rear part of the enclosure for cable connection removing the existing cable CLASSTIBEVICE DA 3 Audio s a Valencia MADE IN SPAIN 2 Screw the cables to the barrier strip following the label indications INPUT OUTPUT 3 Fix the cover of the rear part of the enclosure with six screws Don t remove after installation Manual del Usuario WR series User s Manual TECHNICAL SPECIFICATIONS Technical Specifications RMS Average Power Handling Program Power Handling Peak Power Handling On axis Frequency Range 10dB Nominal Minimum Impedance On axis Sensitivity 1w 1m Rated Peak SPL at full power Nominal 6dB Beamwidths Enclosure Material Color Finish Transducers Replacement Parts Dimensions H x W x D Net Weight Optional Accessories EN54 24 Based Technical Specifications Nominal Power On axis Frequency Range 10dB Nominal Impedance Minimum Impedance On axis Sensitivity 1w 4m Measured Maximum SPL at 4m Horizontal Coverage Angles 6dB Vertical Coverage Angles Enclosure Material Color Finish Transducers Replacement Parts Environmental Type Environmental Performa
16. slings or chains will determine the vertical orientation Alternatively the back bottom eyebolt point can be used to provide vertical orientation The ANL 2 set is an optional set of four eyebolts and four carabiners Dimensions below are in millimetres In the case of the ANL 2 eyebolt this means that the 200 kg working load becomes 60 kg at 45 degrees Do not use eyebolt flying if the load angle is higher than 45 degrees O Degrees 30 Degrees 45 Degrees More than 45 Degrees 3096 2596 10096 6596 96 of working load DO NOT USE FOR SUSPENSION NO USE PARA EL COLGADO 90 The following illustrations show different views on eyebolt flying for a single box The length of the back cables or chains determines the vertical angle of the box A f El d AN Au ih i 0 ii E li B 3 f HA Y Ig Each ANL 2 eyebolt has a rated working load 3 Tu of 200 kg 440 Ib Each ANL 2 carabiner has 0 8 P li working load of 330 kg 726 lb If using other mi hardware make sure it is rated to handle the required load E When using eyebolts it is important to bear in UJ mind that the rated working load is only true for a K load applied in the plane of the eye and is n significantly reduced for other angles The drawing illustrates the concept The table shows the 4 variation of the working load as a
17. use D A S loudspeakers equipped with robust 4 voice coils and the M 75 compression driver with 1 5 exit and a 3 voice coil These models with 60 x 40 horn geometry All the speaker components are treated for weather resistance and extended durability in extreme environments The WR series enclosures are manufactured using exterior grade plywood Black white or military grey color options are available in both exposure ratings IP56 according to IEC 60529 standards The perforated stainless steel protective grilles are painted to match the cabinet finish and backed with foam over a vapor barrier to avoid the entry of water The barrier strip connector is protected by a waterproof cover and the connection wire equipped with a cable gland Models and versions WR 8826 WR 8826CX covered exposure black WR 8826DX direct exposure black WR 8826CXW covered exposure white WR 8826DXG direct exposure grey WR 6412 WR 6412CX covered exposure black WR 6412DX direct exposure black WR 6412CXW covered exposure white WR 6412DXG direct exposure grey 9 Jo WR 6415 WR 6415CX covered exposure black WR 6415DX direct exposure black WR 6415CXW covered exposure white WR 6415DXG direct exposure grey Em 2 WR 8826 WR 6412 WR 6415 LINE DRAWINGS ALL DIMENSIONS
Download Pdf Manuals
Related Search