Installation Guide
Contents
1. m Em g Lead Or follow WLL l R 1 Install Instructions For p WLL TR 1p WLL TX1 transmitter and WLL RX1p receiver amp Transmitter Box Contents Receiver Box Contents TX unit Transmitter 1 WLL TX1 wirelesstransmitter 1 WLL RX1pwirelessreceiver amp unit 1 5vpowersupply 1 32vpowersupply 2 Halfrackmountadapters 2 Halfrackmountadapters 2 Antenna 2 Antenna 2 Two pin Euro block connectors RX unit Receiver Amp Antenna 4 Front Rear TX unit Transmitter TX unit Transmitter ene WLL TX 1 Ta olHmro Ole INPUT GAIN BALANCED IN DCINSV USB IN RX unit Receiver Amp RX unit Receiver Amp WLLL RX ie A SOUNDTUBE a WLL RX ie SPEAKER OUT SPEAKER OUT ii rita Oa NS DCIN32V 1 435 647 9555 800 647 TUBE www soundtube com 2012 SoundTube Entertainment Inc All rights reserved PN INS WLL TR 1p Rev01 27 12 fAlwerning SoundTube products must be installed by a professional audio installer contractor For safety and for optimum audio performance installer must follow all directions issued by SoundTube Entertainment Install Instructions For WLL TR 1p WLL TX1 transmitter and WLL RX1p receiver amp WLL TR 1p WLL TX1 Install Instructions 2 Determine location for placement of WLL TX1 The WLL TX1 may be installed in an equipment rack half rack adapter required or on a shelf 1 Remove unit from box2. 8 Selecteitherthe Stereo or Mono operation mode viathe selector switch onthe front panel Note If the signal appearing at the receiver is intermittent or noisy a make sure the transmitter s RF Gain switch is on High b change the location of the transmitter and or receiver for line of sight position with one another c place the antennas in a line of sight position using an antenna extension cable available from third party vendors WLL TR 1 Install Instructions For p WLL TR 1p WLL TX1 transmitter and WLL RX1p receiver amp Transmitter Interference If the WLL TX1 causes interference with other wireless devices in the area try the following a select a different channel setting on both the transmitter and receiver step 10 b change RF Gain switch to Low setting step 7 c alter antenna positions on both transmitter and receiver antenna positions should match each other If using two WLL TX1 units separate them by at least 2 ft If using 3 separate them by at least 5 ft When using more then 3 transmitters the RF switch should be set to low if the systems are within 60 70 ft of each other If they have problems establishing a link with the WLL RX1 move the WLL TX1 s further apart The transmitting signals can interfere with each other if they are too close together FCC Notice This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause h
3. SOUNDTUBE WLL TX 3 Connect desired input source to rear panel You may use balanced 1 4 TRS connectors unbalanced mini or USB Multiple sources may be connected but only the source selected on the input switch step 5 will be sent to the transmitter When connecting through the USB input do not connect an input to the balanced or line in LINE IN LINEOUT LINEIN BALANCED IN 4 If desired the variable LINE OUT mini jack can be connected to an external device such as an ADA hearing assistance system Installation Notes 2a an installation that puts the WLL TX1 in line of sight with the WLL RX1 p will provide the best results 2b Do not install transmitter more than 230 feet 70 meters line of site or 50 meters indoors from the desired receiver location s 3a If using the USB input the WLL TX1 will appear as an audio device on your computer s control panel 6 Set RF power switch Two options are available High H 5 Set input switch to match the desired input source and Low L The High setting is recommended for maximum distance The low setting is for installations where 2 or more TX 1 s are on the same channel within 60 70 ft of each other aa 7 SOUNDTUBE WLL TX WIRELESS CHANNEL 9 Connect power supply to DC IN 5V connector channel 1 2 or 3 NOTE the WLL RX1 p unit s must be set on the same channel 10 On front panel select transmit 7 Set INPUT sensit
4. antennes install es doivent tre situ es de facon a ce que la population ne puisse y tre expos e a une distance de moin de 20 cm Installer les antennes de facon a ce que le personnel ne puisse approcher a 20 cm ou moins de la position centrale de I antenne La FCC des Etats Unis stipule que cet appareil doit tre en tout temps loign d au moins 20 cm des personnes pendant son functionnement IC Notice This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Only for detachable antennas This radio transmitter identify the device by certification number or model number if Category II has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated Antenna types not included in this list having a gain greater
5. than the maximum gain indicated for that type are strictly prohibited for use with this device Le pr sent metteur radio identifier le dispositif par son num ro de certification ou son num ro de mod le s il fait partie du mat riel de cat gorie a t approuv par Industrie Canada pour fonctionner avec les types d antenne num r s ci dessous et ayant un gain admissible maximal et I imp dance requise pour chaque type d antenne Les types d antenne non inclus dans cette liste ou dont le gain est sup rieur au gain maximal indiqu sont strictement interdits pour l exploitation de l metteur Gain d antenne 2 0dBi maximal Type d antenne 50 Q BNC monopole antenne For Module only Information for the OEMs and Integrators This device is intended for OEM integrators only Please see the full Grant of Equipment document for restrictions This device must be operated and used with a locally approved access point Label Information to the End User by the OEM or Integrator If the FCC ID of this module is not visible when it is installed inside another device the the outside of the dvice into which the module is installed must be labeled with Contains FCC ID SU3RM2400A in a visible area
6. armful interference and 2 this device must accept any interference received including interference that may cause undesired operation Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or rel
7. ht of the Euroblock connectors Do not connect both Be certain to check for the correct connection polarity SOUNDTUBE WLL RXie LINE IN LINE OUT 4 If desired a direct audio source can be connected to the WLL RX1p via the mini LINE IN jack Note If an audio source is connected to this input it will interrupt any RF feed being sent via the WLL TX1 Installation Notes 2a an installation that puts the WLL TX1 in line of sight with the WLL RX1 p will provide the best results 2b Do not install transmitter more than 230 feet 70 meters line of site or 50 meters indoors from the desired receiver location s 3a Unit output is 50 watts per channel SOUNDTUBE WLL RX iP LINE IN LINE OUT 5 If desired a fixed LINE OUT audio signal is provided by the stereo mini jack for operating a device such as an ADA hearing assistance system Pp REO _ WIRELESS CHANNEL 1 a O 3 9 Select the receiving channel 1 2 or 3 on the front panel NOTE the WLL TX1 must be set on the same channel 6 For best results Transmitter and Receiver antennas should face the same direction either vertically or horizontally SOUNDTUBE STEREO WIRELESS CHANNEL 0 10 Apply power to unit Adjust front panel gain control as needed 7 Connect the power supply to the DC IN 32V power connector 11 Done STEREO WIRELESS C
8. ivity switch at 0 dB for normal use If using a high output source set the switch to 6dB SOUNDTUBE WIRELESS HE CHANNEL SAIN 11 After installation of WLL RX1 p unit s apply power to WLL TX1 Adjust front panel gain knob as needed The gain control will adjust the level of both the input audio and the LINE OUT feed WETE mmes 2 a a0 8 For bestresults Transmitter and Receiver antennas should face the same direction either vertically or horizontally 12 Done The LED on the front panel will be red when power is applied to the TX unit It will turn blue when the TX unit is in communication with the RX WLL TR 1p WLL RX1p Install Instructions A X eel i 1 Remove unit from box Install Instructions For WLL TR 1p WLL TX1 transmitter and WLL RX1p receiver amp al l 2 Determine location for placement of WLL RX1p The WLL RX1p may be installed in an equipment rack half rack adapter required or on a shelf The antennas may be remoted using a wifi antenna cable not included available through third party vendors 3 Connect 4 ohm or 8 ohm speakers to the L and R channel output leads using the Euroblock connectors and push into place in the appropriate SPEAKER OUT locations Alternatively speakers may be connected via 1 4 plugs at the L and R SPEAKER OUT jacks to the rig
9. ocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication Conform ment a la r glementation d Industrie Canada le pr sent metteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pour l metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique a l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonn e quivalente p i r e ne d passe pas l intensit n cessaire a l tablissement d une communication satisfaisante MPE Notice To satisfy FCC RF exposure requirements a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation To ensure compliance operations at closer than this distance are not recommended Les
Download Pdf Manuals
Related Search