Washer Installation Manual PDF
Contents
1. that the drum rotates normally and that there are no unusual noises that there are no leaks in water supply drain connections that water passes through the detergent compartment and fabric condi tioner compartments that the door cannot be opened using reasonable force during a program Intentionally blank Preventive maintenance 7 1 To keep your machine in proper working order follow the preventive maintenance recommendations provided below The maintenance interval should be adjusted according to machine usage Daily Check the door and door lock Open the door and try starting the machine The machine MUST NOT START Close the door start the machine and try opening the door using reasonable force It MUST NOT BE POSSIBLE TO OPEN THE DOOR WHILE THE MACHINE IS OPERATING Check that the door does not leak Clean the door seal removing any detergent and lint Check that there are no indications of leaks behind or around the machine Clean out any residue remaining in the detergent dispenser nspect liquid chemical tubing and connections for leaks Repair as necessary Every third month refer this service to qualified personnel N May only be carried out by authorized personnel Check that the door does not leak e Check the drain pump strainer and remove any accumulated lint and debris nspect the interior of the machine during an actual wash cycle to ensure that no leaks are not2. Preventive maintenance 1 1 The manufacturer reserves the right to make changes to design material and or specifications without notice Safety instructions The machine is designed for water washing only The machine must not be used by children All installation operations are to be carried out by qualified per sonnel Licensed personnel are necessary for all electric power wiring and plumbing The door interlock must be checked daily for proper operation and must not be bypassed All seepage in the system due to faulty gaskets etc must be repaired immediately All service personnel must be fully familiar with the operating manual before attempting any repair or maintenance of the ma chine The machine must not be sprayed with water Do not add flammable or explosive substances to the wash water They can give off vapors that could ignite or explode Consignes de s curit La machine est concue pour le lavage l eau exclusivement La machine ne peut tre utilis e par des enfants Tous les travaux d installation doivent tre effectu s par une personne qualifi e Tous les c blages lectriques doivent tre r alis s par un lectricien dipl m Le verrouillage du hublot doit tre v rifi chaque jour et ne peut tre neutralis Toute fuite du systeme due des joints d fectueux etc doit tre r par e sans d lai Tous les
3. and a ground lead When the leads are connected together using o an external switch or relay contact the price reduction mode is activated NOTE Each machine must be connected to a separate switch or relay contact Refer to the machine s operating manual for information related to programing a discount value for the price reduction feature Connection of external liquid supply signals Fig The machine can provide three trigger signals for external liquid supply injector pumps The signals are 120V AC and must therefore be routed and connected in accordance with applicable codes Follow the instructions provided in the optional Liquid Supply Kit PN 080693 to connect the liquid supply trigger signal harness to CN6 on the power module at the right rear corner of the machine and to your pumps The trigger signal harness in the kit has 6 leads with signals as follows CN6 1 RED WIRE DETERGENT SIGNAL CN6 2 BLACK WIRE BLEACH SIGNAL CN6 3 BROWN WIRE SOFTENER SIGNAL CN6 4 5 6 BLUE WIRES COMMON Neutral Each trigger signal is activated for 30 seconds at the start of the appropriate segment of a wash program Detergent bleach and softener are then pumped into the corresponding compartments of the soap dispenser which continue to flush for the duration of the fill 5 2 Installation Electrical Connections This appliance must be grounded In the event of an electrical short circuit grounding reduces the
4. clearances recommended Fig Atleast 20 inches 500 mm between the 4 machine and the wall behind Minimum 1 inch 25 mm to next machine if more than one machine is installed in a row Floor The floor must be smooth and hard Do not install the machine on carpet or other soft material The floor must hold the total weight of the machine filled with water and a load This static weight is 400 pounds 180 kilograms e Adjust the leveling legs of the machine as needed to ensure that it is level front to back and side to side and so that all four feet are in contact with the floor Intentionally blank Installation 3 1 Water connections All inlet connections to the machine are to be fitted with manual shut off valves and filters to facilitate installation and servicing NOTE The inlet filter screens are provided inside the machine s connection fittings Water pipes and hoses should be flushed clean before installation After installation hoses should hang in gentle arcs Hoses are to be of an approved type and grade to comply with national regulations The machine has two DN 20 R 3 4 water garden hose water connections Both inlets on the machine must be connected to the water supply or the machine may not function properly Your water heater should supply hot water at a minimum temerature of 120 degrees Fahrenheit 49 degrees Celsius and a maximum of 170 degrees Fahrenhe
5. membres du personnel d entretien doivent tre parfaitement familiaris s avec le manuel d entretien avant d entreprendre une r paration ou un entretien de la machine Ne jamais asperger d eau la machine sous peine de risquer un court circuit Ne pas utiliser dans la machine des adoucissants textiles contenant des liquides volatils ou inflammables Intentionally blank Technical data Technical data WHWF09810M NM EHWF09810M NM Innerdrum volume litres ft 98 3 5 diameter mm inch 554 21 4 5 Drum speed wash rom 45 extraction max rpm 1000 G factor 306 Weight net 136 300 WHWF09810M NM Water valves DN20 connection 3 4 GH Rec water pressure psi 30 90 kPa 200 600 Functioning limits psi 8 145 for water valve kPa 50 1000 2 6 Capacity at 45 psi 300 kPa gallon min liter min 10 Drain hose inch 1 outer mm 25 Draining gallon min 5 capacity liter min 1 1 1 2 Technical data Power line Air Vent for Safety Hot water Cold water Drain Coin meter coin operated models only Control panel Detergent dispenser Door 1 2 3 4 5 6 T 8 9 NOTES A 1109mm 43 5 8 inch B 1010mm 39 3 4 inch C 592mm 23 3 8 inch D 293mm 11 1 2 inch E 686mm 27 inch 56mm 29 7 8 inch Install
6. risk of electric shock by providing an escape wire for the electric current This appliance is equipped with a cord having a grounding wire with a grounded plug The plug must be inserted into an outlet that is properly installed and grounded A Improper use of the plug can result in a risk of electric shock Consult a qualified electrician or service person if the grounding instructions are not completely understood or if doubt exists as to whether the appliance is properly grounded Wiring Requirements e This appliance must be plugged into 15 or 20A 120 VOLT 60 HZ GROUNDED OUTLET Note Where a standard two prong outlet is encountered Fig itis the personal responsibility and obligation of the consumer to have it replaced with a properly grounded three prong outlet Extension Cords DO NOT use an extension cord with this product A Power Interruptions Occasionally there may be power interruptions due to thunderstorms or other causes Following a power outage the machine will resume operation at the point where it was when the power failed During a power failure the loading door will be UNLOCKED once the drum has come to a stop This allows garments to be removed in the event of a prolonged power outage Function checks 6 1 Function checks Perform the following checks once the machine is installed Open the water supply valves Press the START button or if needed insert coins and press START Check
7. 8 Replace top cover if previously removed Cold Warm Hot Delicate HeavySoil Extra Rinse Start Price Time Remaining Frio Templado Caliente Delicado Sucio Enjuage Comienzo Precio Tiempo a P A Established in 1955 Wascomat has sold more commercial washers than anyone else in the industry Wascomats years of service have made it the most trusted name in commercial laundry The heritage of the Wascomat brand is rooted in the origin of the Self Service OPL and Facility Management laundry industry Everyday across North America customers choose Wascomat equipment for all their laundry needs Having updated your laundry with Wascomant Is a wise choice for many reasons Wascomat offers what no other can value performance reliability and heritage To learn more about additional Wascomant products and services for all your laundry needs please visit our website at laundrylux com If your business is in need of laundry expansion large or small Laundrylux Financial Services is ready to help you get there Leasing and financing is available at the most competitive rates on all Wascomat products Wascomat Sales and Administration 516 371 4400 Spare Parts 516 371 2000 Technical Support 516 371 0700 En Mexico 001 800 010 1010 461 Doughty Blvd Inwood NY 11096 laundrylux com
8. CROSSOVER SEES In a class by itself MODEL NO WHWF09810M NM MODEL NO EHWF09810M NM WASHER INSTALLATION MANUAL gt Laundrylux DOC NO 096417 EDITION 13 2011 ATTENTION INSTALLER Fig For coin operated models the coin meter housing is packed UNDER the machine DO NOT DISCARD THE PACKING MATERIALS without first removing the meter housing See installation instructions later in this manual for details ATTENTION INSTALLER Four transportation bolts are installed in the rear of the machine to protect the suspension and tub assembly from damage during shipment REMOVE ALL FOUR BOLTS AND PLASTIC TUBES THROUGH WHICH THE BOLTS PASS BEFORE OPERATING THE MACHINE See instructions later in this manual Installation manual WHWF09810M NM EHWFO09810M NM WARNING ALL OPERATING AND MAINTENANCE PROCEDURES SHOWN ON THE NEXT PAGE OF THIS MANUAL MUST BE FOLLOWED DAILY FOR PROPER OPERATION OF YOUR MACHINE PLEASE ENTER THE FOLLOWING INFORMATION AS IT APPEARS ON THE MACHINE S DATA PLATE S MACHINE TYPE OR MODEL MACHINE SERIAL NUMBER S ELECTRICAL CHARACTERISTICS VOLTS PHASE KEEP THIS MANUAL IN A SECURE PLACE FOR FUTURE REFERENCE 244824 05 Intentionally blank SAFETY AND WARNINGS SIGNS Replace If Missing Or Illegible One or more of these signs must be affixed on each machine as indica ted when not included as part of the front instruction panel LOCATED ON THE FRONT OF THE DETERGENT DIS
9. PENSER INSTRUCTIONS INSTRUCCIONES DE USO Load washer and close door Cargue la lavadora cierre la puerta O Add detergent 1 3 cup only O Agregue detergente s lo 1 3 de taza O Select cycle and options O Seleccione el ciclo de lavado y la opci n O Pay O Pagar O Press START Presione boton de empezar START he USE ONLY HE HIGH EFFICIENCY DETERGENT he USE SOLAMENTE UN DETERGENTE DE HE ALTO RENDIMIENTO IMPORTANT SAFETY INSTRUCTIONS IMPORTANTES MESURES DE SECURITE WARNING To reduce the risk of fire electric chock or injury to persons when using your appliance AVERTISSEMENT Pour r duire les risques d incendie de choc lectrique ou de blessure quand l appareil est utilis 1 Read all instructions before using the appliance 2 10 11 12 Lire toutes les instructions avant d utiliser l appareil This machine must be installed according to the installation instructions Ce machine doit tre visse sur le plancher selon les instructions d installation This machine MUST be serviced and operated in compliance with manufacturers instructions CHECK DOOR LOCKS EVERY DAY FOR PROPER OPERATION TO PREVENT INJURY OR DAMAGE IF THE DOOR LOCK FAILS TO OPERATE PROPERLY PLACE THE MACHINE OUT OF ORDER UNTIL THE PROBLEM IS CORRECTED IL FAUT QUE cette appareil soit entretenue et actionn e conformement aux instructions du fabriquant CONTROLEZ LA SERRURE DE PORTE TOUS LES JOURS AFIN DE EVI
10. TER DES DOMMAGES OU DES RISQUES PERSONNELLES SI LA SERRURE DE PORTE NE FONCTIONNE PAS IL FAUT METTRE LA MACHINE HORS SERVICE JUSQU LE PROBLEME SOIT CORRIG Do not wash articles that have been previously cleaned in washed in soaked in or spotted with gasoline drycleaning solvents or other flammable or explosive substances as they give off vapors that could ignite or explode Ne pas laver des articles qui ont t nettoy s ou lav s avec de l essence des solvants pour nettoyage sec ou d autres substances inflammables ou explosives ou que l on a fait tremper dans ces produits Ces substances d gagent des vapeurs qui peuvent s enflammer ou exploser Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances giveoff vapours that could ignite or explode Ne pas ajouter d essence de solvants pour nettoyage sec ou d autres substances inflammables ou explosives l eau de lavage Ces substances d gagent des vapeurs qui peuvent s enflammer ou exploser Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period before using a washing machine turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas As the gas is flammable do not smoke or use an op
11. ation 2 4 Installation For safety two people should install this product Leave the machine on the transport pallet until it can be placed in the final prepared position First remove all the packing materials Upon opening of the package water drops may be seen on the plastic bag and the drum This is a normal phenomenon resulting from water tests in the factory NOTE 1 A bottom cover plate is wrapped in the top of the packing material 2 A coin meter housing is wrapped in the base Tilt the machine to the left to remove it from the packing 3 Be careful while handling the bottom cover and coin box 4 Remove all anti scratch film from the washer Install the bottom cover plate Fig 1 Lay the package carton on the ground 2 Lay the washer slowly down on its back on the package carton 3 Install the bottom cover on the bottom of the machine using the 8 screws provided in the accessories bag 4 Lift the washer to the upright position Back Side Package Carton 2 2 Installation Transportation Bolts The washer is fitted with transportation bolts to prevent internal damage during transportation Transportation bolts must b
12. e removed before using the washer Removing Transportation Bolts Fig 1 Unscrew the 4 bolts with a wrench Remove the lower 2 bolts first then the upper two 2 One of the bolts retains the power cord of the washer to prevent operating without removing bolts Screws 2 Remove the bolts and the sleeves to release the power cord Keep the 4 bolts and sleeves for future use NOTE If transportation bolts and sleeves are not removed it may cause severe vibration noise and malfunction as well as damage to the machine NOTE When the washer is transported the transportation bolts and the sleeves must be reinstalled 3 Close the 4 holes with the caps supplied Install the coin meter housing Fig 1 Take out the coin meter housing from the base 2 Unscrew the 4 bolts provided on the coin vault put the coin meter housing on the vault a carefully feeding the two wiring harnesses into the housing 3 Install and tighten the 4 bolts securely 4 Install the front plate of the coin meter and fasten it b 5 Install the coin meter c 6 Plug the coin meter s into the Coin 1 Red and Coin 2 White harnesses 7 Install the cover of the coin meter housing d Installation 2 3 Siting Install the machine close to a drain standpipe or floor drain and within 4 feet of the water supply ee spigots In order to make installation and servicing the machine easier the following
13. en flame during this time De l hydrog ne peut tre produit dans un syst me eau chaude qui n a pas t utilis depuis deux semaines ou plus L HYDROG NE EST EXPLOSIF Si le syst me eau chaude n a pas t utilis depuis un certain temps ouvrir tous les robinets d eau chaude et laisser l eau couler pendant plusieurs minutes avant d utiliser une laveuse l hydrog ne accumul le cas ch ant s chappera L hydrog ne tant inflammable ne pas fumer ou utiliser un appareil flamme nue pendant que l eau coule Do not allow children to play on or in the appliance Close supervision of children is necessary when the appliance is used near children Ne pas permettre aux enfants de jouer sur ou dans l appareil Surveiller triotement les enfants lorsqu ils se trou vent pr s d l appareil qui fonctionne If the machine is to be discarded remove the door to prevent accidental entrapment Avant de mettre l appareil hors service ou de jeter retirer la porte Do not reach into the appliance if the tub is moving Ne pas mettre la main dans l appareil lorsque la cuve bougent Do not install or store this appliance where it will be exposed to the weather Ne pas installer ou placer cet appareil dans un endroit ou il sera expos aux intemp ries Do not tamper with controls Ne pas trafiquer les commandes Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user main
14. iced by Turning of the main power switch of the machine Remove the top panel Start a wash program KEEP CLEAR OF MOVING PARTS WHILE MACHINE IS OPERATING Inspect all internal hoses seals and gaskets for signs of leakage Repair as necessary Check that water inlet screens are clean of debris Dirty screens result in longer fill times reducing productivity Inspect the drive belt Adjust the tension or replace as necessary Check that there are no signs of leakage on the floor beneath the machine Locate and repair any leak Contact your local dealer or Laundrylux Technical Support at 516 371 0700 if you have questions regarding installation operation or maintenance of your machine 8 1 Installation OPL MODE SETUP To convert the machine for OPL operation the front control display module must be reset to coin mode and the prices of all six cycles and options must be set to 0 00 Fig 1 Reset Control Display Module Method A 1 Remove top cover of machine Secured with two T15H security Torx fasteners 2 Locate small red reset button behind the left digit in the display Press and hold down button 3 After several seconds the control module will chime and the 4 segment display will show 0 25 The washer is now in coin mode Method B 1 Partially pull out detergent dispenser drawer 2 Depress and unlock tab in the top back of the drawer with a screw driver remove dispenser 3 Remove the tw
15. iption and location of the signs Missing or illegible ones must be replaced imme diately Be sure you have spare signs and labels available at all times These can be obtai ned from your distributor or from Laundrylux 2 Check the door safety interlock as follows a OPEN THE DOOR of the machine and attempt to start in the normal manner For coin operated models insert the proper coins to start the machine For card operated models insert the card to start the machine THE MACHINE MUST NOT START D CLOSE THE DOOR to start machine operation and while it is operating attempt to open the door without exerting extreme force on the door handle The door should remain locked If the machine can start with the door open or can continue to operate with the door unlocked the door interlock is no longer operating properly The machine must be placed out of order and the interlock immediately replaced DO NOT UNDER ANY CIRCUMSTANCES ATTEMPT BYPASS REWIRE ANY OF THE MACHINE SAFETY DEVICES AS THIS CAN RESULT IN SERIOUS ACCIDENTS 4 Be sure to keep the machine s in proper working order Follow all maintenance and safety procedures Further information regarding machine safety service and parts can be obtained from your dealer or from Laundrylux through its Teletech Service Hotline 516 371 0700 All requests for assistance must include the model serial number and electrical characteristics as they appear on the machi
16. it 77 degrees Celsius The required water pressure is as follows min 15 PSI 100 kPa e max 90 PSI 600 kPa recommended 30 90 PSI 200 600 kPa 3 2 Installation Water type Water connection 1 2 o cold and hot hot cold Installation 4 1 Drain connection Connect the machine s drain hose to the back of the washer using the spring clamp provided in the accessories package Avoid sharp bends in the hose which may prevent proper draining Fg You can connect the drain hose to a sewer stand pipe If you do this make sure that the outlet hose will not come out of the stand pipe You can connect the drain outlet to a sink or basin If you do this make sure the outlet hose will not come out of the sink or basin Legend 94 inches 239centimeters maximum 30 inches 76 centimeters minimum Machine Drain outlet hose Intentionally blank Installation 5 1 AN AIA AN Electrical installation must be carried out All optional equipment connected must be by licensed qualified personnel EMC approved to EN 50081 1 or EN 50082 2 Connection of external price reduction control signal Fig The accessories package includes a two wire harness for price reduction promotion activation The harness mates with a connector on the machine s front main control circuit board The price reduction harness carries a 5VDC o o signal lead
17. ne identification plate Insert this information in the space provided on the previous page of this manual 9 WARNING NOT OPERATE MACHINE S WITH SAFETY DEVICES BYPASSED REWIRED INOPERATIVE DO NOT OPEN MACHINE DOOR UNTIL DRUM HAS STOPPED ROTATING AVERTISSEMENT NE PAS FAIRE FONCTIONNER LA LES MACHINE S AVEC UN DISPOSITIF DE SECURITE NEUTRALISE RECABLE OU NON OPERATIONNEL NE PAS OUVRIR LA MACHINE TANT QUE LE TAMBOUR NE S EST PAS IMMOBILISE NOTICE TO INSTALLER Improper installation of this machine May cause serious damage to the machine May result in other property damage May cause personal injury Will void the manufacturer s warranty Location Requirements e The location for your washer should have a flat and even floor This will improve performance minimize noise and decrease washer movement The unit can be installed in a laundry room or other recessed area Additional Requirements e A grounded electrical outlet Recommended less than feet from washer tis not recommended to use washer on soft flooring such as carpets or foam Do not operate washer if ambient room temperature is less than freezing as this can cause damage to the unit Contents Contents D C 1 1 SO n 2 1 Water connections eee se nec dde 3 1 Drain ConNNeCtON ee 4 1 Connection of external liquid supplies 5 1 FUNCHON 61 9 2101 NR RT 6 1
18. o large Phillips head screws that secure the display controller to the machine 4 Slide display module to the left and pull forward being careful not to damage the cables coming out of the back of the controller 5 Reset module as above 6 Replace and re secure control display module using original mounting screws Remount detergent dispenser drawer Fig 1 Diagram showing reset button on back of the Display CPU To be created Fig 2 Set Program and Options Pricing Set all six programs and options to 0 00 1 With top cover off press and release the black service mode plunger switch behind the card reader mounting plate The display will go blank Alternatively with the top cover left on the service mode switch can be activated using a screw driver inserted in the card slot in the front of the machine 2 Press COLD Program price is displayed 3 Press START The current price blinks indicating it 15 available for editing 4 Press four program buttons COLD WARM HOT amp DELICATE to set price to 0 00 Each button increments a corresponding digit left to right in the price Each digit rolls over from 9 to 0 without affecting other digits The left most digit cannot be programmed to 0 but can be blanked out 5 Press START to save value 6 Press WARM and repeat steps 3 5 Repeat until all of the programs and options six total are set to zero 7 Press and release service mode switch to return normal mode
19. tenance instructions or in published user repair instructions that you understand and have the skills to carry out Ne pas r parer ou remplacer les pi ces de l appareil ou proc der l entretien de celui ci sauf si les instructions visant l entretien et les r parations qui doivent tre effectu s par l utilisateur le sp cifient si vous comprenez bien ces instructi si vous poss dez les connaissances n cessaires MANUFACTURED BY HAIER EXCLUSIVELY FOR LAUNDRYLUX NOTICE TO OWNERS OPERATORS AND DEALERS IMPROPER INSTALLATION AND INADEQUATE MAINTENANCE POOR HOUSEKEEPING AND WILLFUL NEGLECT OR BYPASSING OF SAFETY DEVICES MAY RESULT IN SERIOUS ACCIDENTS OR INJURY TO ASSURE THE SAFETY OF CUSTOMERS AND OR OPERATORS OF YOUR MACHINE THE FOLLO WING MAINTENANCE CHECKS MUST BE PERFORMED ON A DAILY BASIS NOTICE A DES PROPRI TAIRES UTILISATEURS ET REVENDEURS UNE INSTALLATION INCORRECTE ET UN ENTRETIEN INAD QUAT DE M ME QUE LA N GLIGENCE OU LA NEUTRALISATION DELIBEREES DES DISPOSITIFS DE S CURIT PEUVENT ETRE CAUSES DE BLESSURES OU D ACCIDENTS S RIEUX POUR ASSURER LA S CURIT DES CLIENTS ET OU DES UTILISATEURS DE VOTRE MACHINE IL EST INDISPENSABLE DE PROC DER CHAQUE JOUR AUX CONTROLES DE ROUTINE CI APRES Prior to operation of the machine check to make certain that all operating instructions and warning signs are affixed to the machine and legible See the following page of this manual for descr
Download Pdf Manuals
Related Search