PONY 20 SCA CARPET EXTRACTOR
Contents
1. VIS METALLIQUE 3 See GROUNDED QUTLET BUX GROUNDING 7o BOITE DE SORTIE j BLADE GRDUNDED DUTLET BDX RC IEE A LA TERRE BLADE GROUNDED OUTLET BOX FICHE BOITE DE SORTIE FICHE BOITE DE SORTIE ERRE RELIEE A LA TERRE ERRE RELIEE LA TERRE NOTE In Canada the use of a temporary adaptor is not permitted by Canadian electrical code ALL REPAIR SERVICE MUST BE PERFORMED BY AN NSS AUTHORIZED DISTRIBUTOR SERVICE STATION USING ONLY NSS ORIGINAL EQUIPMENT SAVE THESE INSTRUCTIONS IMPORTANTES INSTRUCTIONS DE SECURITE MISE A LA TERRE DE L QUIPEMENT LECTRIQUE conducteur de mise a la terre peut mener a un risque de choc lectrique V rifier aupr s d un lectricien ou d un r parateur qualifi si vous avez des doutes quant la mise la terre appropri e de la prise Ne pas modifier la fiche fournie avec l appareil si elle n entre pas dans la prise faire installer une prise appropri e par un lectricien qualifi AVERTISSEMENT Toute mauvaise connexion de l appareil Toujours utiliser une rallonge 3 fils mise la terre et prises m le et femelle Si vous utilisez une rallonge de 25 pieds la capacit lectrique de transport doit tre d au moins 14 3 ST les rallonges de 50 pieds d au moins 12 3 ST INSTRUCTIONS DE MISE A LA TERRE Cet appareil doit tre mis la terre lorsqu il est en marche pour prot ger l op rateur de tout choc lectrique L appareil est fourn2. Use an air mover dryer to speed up the drying time Do not apply water more than twice in one area to prevent excess wetting Over wetting can damage the carpet and the underlying floor SPECIAL CLEANING This machine may be used to perform special cleaning jobs other than normal scrubbing Double Scrubbing This procedure provides deeper cleaning on heavily soiled floors Double scrub by making a second pass over the carpet with only the brush turned on Then make a third pass with the solution pump vacuum and brush on to remove the most dirt Make an additional vacuum pass to dry the carpet as much as possible The slower the cleaning pass the more dwell time increasing the amount of dirt that is removed from the carpet OPTION ACCESSORY CLEANING Cleaning upholstery stairs or confined areas e Prepare the solution recovery tanks as you would for normal carpet cleaning Select the correct tool for the job to be performed Remove the quick connect that is attached to the accessory spray wand hose by pushing the outer collar back and pulling on the hose fitting Connect the solution hose which is part of any of the accessory kits push the outer collar back and insert the hose fitting fully Release the collar to secure the hose in place Solution from the solution tank is supplied to this outlet when the solution pump is ON but will only dispense solution when the trigger of the upholstery stair tool o
3. 60H7 230V 60H7 ee 1 PHASE lt GROUNDING CLIP ND PATTE DE MISE A LA TERRE METAL SCREW VIS METALLIQUE GROUNDED OUTLET BOX ue GROUNDING BOITE DE SORTIE GROUNDING BLADE GROUNDED OUTLET BOX BLADE GROUNDED OUTLET BOX FICHE BOITE DE SORTIE BESIDE A LA TERRE FICHE BOITE DE SORTIE ERRE RELIEE A LA TERRE ERRE RELIEE A LA TERRE REMARQUE Au Canada l utilisation d un adaptateur temporaire est interdite par le code d lectricit canadien TOUTES LES R PARATIONS DOIVENT TRE EFFECTU ES PAR UN DISTRIBUTEUR STATION SERVICE AUTORISE E NSS UTILISANT SEULEMENT DES PIECES ORIGINALES NSS CONSERVER CES INSTRUCTIONS nis NOISE AND VIBRATION NOISE Sound pressure level at Operator 75dB A position VIBRATION Weighted RMS acceleration value 195 m s ISO 5349 MACHINE INSPECTION e Now that the machine is unpacked remember to recycle all packing materials e Inspect the machine for damage or missing components If damage is found contact the local freight company to file a freight claim MACHINE COMPONENTS Solution Tank The solution tank is the lower part of the machine body It has a capacity of 20 Gallons 75 liters Recovery Tank The recovery tank is the upper part of the machine body It has a capacity of 20 gallons 75 liters Control Panel The operator control panel is located at the upper rear area of the machine Operator controls are positioned for ease of use an
4. Brush Head Assembly This machine has a floating brush head assembly that adapts to the different carpet pile heights The brush head is offset to the left side of the machine to clean against the wall e The brush shoe and brush head float and will swing out from the wall if they get too close to the wall This avoids gouging the wallboards or the wall e The brush is a 22 wide nylon bristle four row chevron design e The brush head assembly includes the Solution Spray System Spray Bar and five Spray Tips Solution is applied to the carpet through these tips Vacuum Shoe The vacuum shoe is a 27 wide weighted aluminum casting Mounted with a bearing and a nylon bushing itis able to swing and swivel on a center arm As the machine moves forward the vacuum shoe pulls the liquid out of the carpet Body Casters Chassis Wheels Two 8 diameter grooved non marking rubber tread clutch type bearing wheels allows this machine to be pushed forward without the use of the drive motor These wheels will rotate freely when turned toward the front of the machine clockwise on the right counterclockwise on the left Two 4 diameter swivel casters are mounted on the steel frame at the rear of the machine they provide maneuverability and stable control of this machine Float and Screen Assembly Vacuum air is removed from the recovery tank via the float and screen assembly as the water level rises so does the float When th
5. Failure to perform this procedure may result in poor machine performance machine component damage and failure This procedure should be performed by an NSS authorized distributor or service center Repairs performed by an unauthorized company will void the machine warranty If you require assistance finding an authorized service center please contact NSS Enterprises Inc After every 750 hours of operation e Inspect the vacuum motor carbon brushes for wear Replace the vacuum motor carbon brushes when they are 7 16in 11mm in length Check the belt to the brush for wear and tightness The swivel and wheel bearings must be lubricated on a regular basis to ensure trouble free operation Use non water soluble grease for lubrication The drive chain tension should be checked every 90 days and adjusted if necessary To adjust the drive chain tension you must first loosen the four hex bolts in the chassis slots under the propulsion motor Slide the motor forward to decrease or BRUSH MOTOR BRUSH ASSEMBLY BELT The brush motor brush assembly and belt are serviced by removing both parts of the plastic two piece brush housing cover The brush drive belt tension is adjusted by first loosening the brush motor mounting hex nuts Slide the motor toward the brush to decrease the tension and away from the brush to increase the tension When the motor is in the proper position the drive belt should have 1 4 to 3 8 deflection midway
6. If the machine has been used previously cleaning solution may have settled into the spray jets and dried clogging them e In order to check the spray jets you must remove the spray jet bar from the brush housing e Disconnect the quick connect on the end of the solution hose from the quick connect on the spray jet bar Simply pull out the spray jet bar from the brush head and reconnect the solution hose to the quick disconnect on the spray jet bar Aim the spray jet bar at the carpet Turn ON the master switch then the spray pump Turn the speed control to its slowest speed so the machine does not propel itself Squeeze the deadman switch below the control handle of the machine Solution will spray through the jets and onto the carpet this will allow you to see if all the spray jets are clean If one of the jets is not spraying push in on the spray jet then with just a quarter of a turn in either direction turn the jet and remove it from the spray jet bar Rinse the spray jets with warm water or make a solution of 2596 vinegar and warm water and soak the jets for a few minutes to clean them If an insoluble material is plugging the jets use a wooden toothpick to clean the clogged jet Do not use a knife or other sharp object sharp objects will distort the spray pattern e Reattach the jet to the spray bar by reinserting the tip and turning it clockwise Priming the Solution Pump During normal use the solution ta
7. NEVER operate the machine without the filters in place ALWAYS place this machine on a firm flat surface e NEVER use any attachments other than the manufacturers recommended attachments NEVER spray this machine with water or any liquids NEVER operate this machine outdoors e NEVER expose the machine to rain snow or extreme temperatures e ALWAYS store this machine indoors in a dry cool area NEVER use this machine to dry vacuum a floor or upholstery ALL REPAIR SERVICE MUST BE PERFORMED BY AN NSS AUTHORIZED DISTRIBUTOR SERVICE STATION USING ONLY NSS ORIGINAL EQUIPMENT PARTS SAVE THESE INSTRUCTIONS N nss MANUEL D UTILISATION PONY 20 SCA CARPET EXTRACTOR IMPORTANTES INSTRUCTIONS DE SECURITE Lisez toutes les instructions avant d utiliser ou de r parer et faire l entretien de l appareil AVERTISSEMENT Danger de choc ou d lectrocution TOUJOURS d brancher l appareil avant tout entretien ou r paration AVERTISSEMENT Danger de choc ou d lectrocution NE JAMAIS brancher cet appareil une prise lectrique qui n est pas mise la terre correctement Voir les instructions de mise la terre A AVERTISSEMENT Danger d incendie ou d explosion NE JAMAIS utiliser pour ramasser des liquides inflammables ou combustibles ou toute autre chose qui br le ou fume comme des cigarettes des allumettes ou des cendres chaudes NE JAMAIS faire fonctionner cet appareil dans un milieu explosif poussi re
8. c r ali re liquides ou fum es inflammables etc AVERTISSEM ENT Pour r duire le risque d incendies de choc lectrique ou de f blessures UTILISATION PREVUE L extracteur de tapis Stallion 8 SC est un appareil utilisation commerciale pour nettoyer et extraire les planchers les meubles les tentures et l int rieur des voitures dans un milieu int rieur Cet appareil est r serv au ramassage humide NSS ne recommande pas d utiliser ces appareils d autres fins En utilisant un appareil lectrique on doit suivre les pr cautions de bas y compris ce qui suit e TOUJOURS lire et comprendre toutes les instructions avant d utiliser ou de r parer l appareil TOUJOURS utiliser l appareil SEULEMENT selon la description dans ce manuel NE JAMAIS essayer de faire fonctionner cet appareil moins d tre form pour son utilisation NE JAMAIS permettre une personne non form e de faire fonctionner cet appareil NE JAMAIS laisser l appareil branch dans la prise de courant lorsqu il n est pas utilis NE JAMAIS d brancher l appareil de la prise de courant avant qu il ne soit teint SI l appareil ne fonctionne pas correctement a t chapp endommag laiss l ext rieur ou chapp dans l eau retournez le un centre de service NE JAMAIS faire fonctionner cet appareil dans de l eau stagnante NE JAMAIS d brancher ou modifier les interrupteurs ou les dispositifs de s curit NE JAMAIS faire fonctionn
9. AMAIS faire fonctionner l appareil sans que les filtres ne soient en place e TOUJOURS placer cet appareil sur une surface ferme et plat e NE JAMAIS utiliser d accessoires autres que ceux recommand s par le fabricant e NE JAMAIS pulv riser cet appareil d eau ou d autres liquides e NE JAMAIS faire fonctionner l appareil l ext rieur e NE JAMAIS exposer l appareil la pluie la neige ou des temp ratures extr mes TOUJOURS ranger cet appareil l int rieur dans un endroit sec et frais DO NOT use this machine to dry vacuum a floor or upholstery TOUTES LES R PARATIONS DOIVENT TRE EFFECTU ES PAR UN DISTRIBUTEUR STATION SERVICE AUTORISE E NSS UTILISANT SEULEMENT DES PIECES ORIGINALES NSS CONSERVER CES INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS GROUNDING OF ELECTRICAL EQUIPMENT WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded Do not modify the plug provided with the machine if it will not fit the outlet have a proper outlet installed by a qualified electrician Always use a properly grounded 3 wire extension cord which has male and female plugs If 25 foot extension cords are used the electrical carrying capacity should be no less than 14 3 ST 50 foot extension cords no less than 12 3 ST GROUNDING INSTR
10. OPERATION MANUAL PONY 20 SCA CARPET EXTRACTOR IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using or servicing machine WARNING Shock or electrocution hazard ALWAYS unplug machine before performing any maintenance or service A WARNING Shock or electrocution hazard NEVER connect this machine to an electrical outlet that is not properly grounded See grounding instructions WARNING Fire or explosion hazard NEVER use to pick up flammable or combustible liquids or any thing that is burning or smoking such as cigarettes matches or hot ashes NEVER operate this machine in an explosive atmosphere grain dust flammable liquids or fumes etc A WARNING To reduce the risk of fire electric shock or injury INTENDED USE The Pony 20 SCA Carpet Extractor is intended for commercial use cleaning and extracting floors furniture draperies and automobile interiors in an indoor environment This machine is intended for Wet pickup only NSS does not recommend using these machines for any other purpose When Using An Electrical Appliance Basic Precautions Should Always Be Followed Including The Following e ALWAYS read and understand all instructions before operating or servicing machine e ALWAYS use this machine ONLY as described in this manual NEVER attempt to operate this machine unless you have been trained in its operation NEVER allow an untrained person to operate this machine NEVER leave the machin
11. UCTIONS This machine shall be grounded while in use to protect the operator from electric shock The machine is provided with a three conductor cord and a three contact grounding type attachment plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances The green conductor in the cord is the ground wire Never connect this wire to other than the grounding pin of the attachment plug Check nameplate on the machine to be sure voltage and cycle stated is the same as the electrical outlet Do not attempt to plug a 120 volt machine into a 240 volt outlet or a 240 volt machine into a 120 volt outlet If the machine is provided with an attachment plug as shown in Figure A below it is intended for use on a nominal 120 volt circuit If a properly grounded receptacle as shown in Figure A is not available an adapter may be installed as shown in Figure B if the outlet box that houses the receptacle is grounded Be sure to fasten the grounding tab the green colored rigid ear lug or the like extending from the adapter with a metal faceplate screw If the machine is provided with an attachment plug as shown in Figure C it is intended for use ona nominal 240 volt circuit No adapter is available for this plug F FIGURE B e RU LE em FIGURE C 115V 60HZ 115V 60HZ SIE Ve 1 PHASE GROUNDING CLIP Dc PATTE DE MISE gt A LA TERRE oo METAL SCREW Ne
12. Will Not Overloaded circuit breaker Reset circuit breaker Unplug other Operate electrical items on same circuit NSS Enterprises Inc 3115 Frenchmens Road Toledo Ohio 43607 PHONE 419 531 2121 FAX 419 531 3761 NSS Enterprises Inc European Distribution Centre Unit Il Pinfold Trading Estate 55 Nottingham Road STAPLEFORD NOTTINGHAM NG9 8AD ENGLAND U K PHONE 44 0115 939 1568 FAX 44 0115 949 0615 Pony 20 SCA Operation Manual Orig 02 06 9094903
13. between the motor and brush pulley To replace the brush drive belt you must remove the brush shaft mounting screw at the pulley end and loosen the screw at the opposite end Install the new belt on the pulleys replace and tighten the brush shaft mounting screws and adjust the belt tension Bristles will wear to the point where there is not enough agitation of the carpet The nylon roller wheel can be raised to lower the brush deeper into the carpet Remove the roller axle that attaches the roller wheel from its holding bracket and reinstall the axle into the upper holes in the bracket WARNING backward to increase the chain tension The drive chain should be lubricated every 90 days with a penetrating moisture resistant lubricant using a spray can with attachable straw to apply Do not use the upper roller axle position with a new or nearly new brush This will force the brush to an exaggerated down position overload the circuit breaker and damage the brush drive DO NOT lubricate the chain when the machine is on a carpeted surface Wipe off any excess lubricant before operating the machine motor Adjustment or replacement of the brush assembly requires removal of both brush shaft mounting screws this allows the brush assembly to be removed from the housing When installing the new brush assembly do not over tighten the shaft screws This will prevent binding of the brush assembly Replacement of the brush drive m
14. cleaning chemicals according to the manufacturer s instructions Fill the tank by pouring the water and cleaning chemicals through the mesh filter that covers the opening at the front of the solution tank Always use a defoamer in the Recovery tank to protect the vacuum motor of this machine Every time the solution tank is filled add 4 to 6 ounces 125 to 188 milliliters of defoamer to the Recovery tank Make sure the clear dome and gasket fits securely on the recovery tank for an airtight seal The vacuum motor will pull the dome down creating a suction during use Connect the Power Cord This machine is equipped with a twist lock power cord e Align the three electrical contacts push the contacts together and turn one of the plugs 1 8 of a turn to lock the two plugs in place This will prevent the machine from disconnecting during use NOTE Some models may have a direct wired power cord Attach the Vac Shoe The vac shoe lift cable is already attached to the lift mechanism for the vac shoe To attach the vac shoe simply slide the tool onto the threaded rod and secure with a washer and nut then slide the vac hose over the stock of the vac shoe The vac shoe is now ready for operation The vac shoe is easily removed for cleaning or machine transportation by removing the nut Checking the Spray Bar and Jets Before attempting to operate the machine it may be necessary to check the spray jets and see if they are clean
15. d include icons for simplified user training This panel has components that control various machine functions e Located in the upper right corner is the master Switch this switch turns the unit on and off it must be turned on before any other switch will work Just below the master switch is the speed control knob this knob controls the forward movement of this machine Note This machine does not have a reverse option In the middle of the control panel are three switches The top switch activates the solution spray the middle switch activates the brushes and the bottom switch activates the vacuum At the bottom of the control panel are two circuit breakers the one on the left is for the brush motor and the one on the right is for the drive motor If the brush becomes over loaded by hair deep pile carpet strings or an obstruction the motor will draw too much current and the circuit breaker will trip Vacuum Motor The vacuum motor is a three stage 1 3 4 HP bypass style with peripheral discharge It is enclosed in a housing to aid in noise reduction and improve airflow cooling Gear Drive Motor A gear reduction motor propels this machine via a chain and sprocket system Variable speed is adjusted at the operator control panel Brush Motor A 1 4 HP permanent magnet motor via a cog belt and pulley system drives the brush Solution Pump This pump is a 100 PSI continuous type three piston bypass valve style
16. e float reaches the top it will shut off the airflow of the vacuum e t does not shut off the vacuum motor e Stop the machine and empty the Recovery tank Accessory Spray Wand Located at the right rear side of the machine this spray wand may be used to pre spray a wide area of carpet before extraction It may also be used to apply additional cleaning solution to trouble spots while extracting Accessory quick connect option This connection is located at the lower left side of the machine The accessory spray wand hose is connected here this connection can be used to attach any of the accessory kits Solution Gage Hose e The amount of fluid in the tank is visible via the clear hose at the back left of the machine As you clean keep an eye on the liquid level refill as needed This hose can be used to drain the tank by pulling down on the hose from the top PREPARING THE MACHINE Preparing the Solution and Recovery tanks Never use water over 140 F 60 C Excessively hot water will damage components such as the pump valves and seals Observe the carpet manufacturer s cleaning instructions Make sure the black drain hose from the Recovery tank is securely closed to keep fluids from draining out To close twist the drain hose plug into the end of the hose with a clockwise rotation Put 1 to 2 gallons 4 to 8 liters of water in the solution tank to help dilute the chemicals and prevent excess sudsing Dilute the
17. e plugged in to the electrical outlet when not in use NEVER unplug the machine from an electrical outlet until after the machine is turned off If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center NEVER operate this machine in standing water NEVER disconnect or modify any switches or safety devices NEVER operate this machine if the cord and or plug has been damaged broken cut abraded or taped e ALWAYS replace the entire cord when the cord or plug is damaged in any way e NEVER handle the machine cord or plug with wet hands NEVER drop or insert any object into any machine opening NEVER operate this machine with any air opening blocked Keep all air openings free of dust lint hair etc NEVER pull or carry the machine by it s electrical supply cord use the cord as a handle close a door on the cord pull the cord around sharp edges or corners expose to heated surfaces run machine over cord or set heavy or sharp objects on the cord NEVER unplug by pulling on the cord To unplug the cord from the outlet grasp the plug not the cord NEVER allow this machine to be used as a toy Close attention is necessary when used by or near children ALWAYS keep face fingers hair or any other body part or loose clothing away from any machine opening or moving part ALWAYS use extreme care when cleaning on stairs or when machine is placed on stairs
18. er cet appareil si le cordon et ou la fiche est endommag e bris e coup e us e ou scell e avec un ruban adh sif TOUJOURS remplacer tout le cordon lorsque ce dernier ou la fiche est endommag e de quelque fa on que ce soit NE JAMAIS manipuler l appareil le cordon ou la fiche avec les mains mouill es e NE JAMAIS laisser tomber ou ins rer un objet dans toute ouverture de l appareil NE JAMAIS faire fonctionner cet appareil lorsqu une ouverture d air est bloqu e Garder toutes les ouvertures d air libres de poussi res peluche cheveux etc e NE JAMAIS tirer ou porter l appareil par son cordon lectrique utiliser le cordon comme poign e fermer une porte sur le cordon tirer le cordon autour de bords ou coins tranchants exposer des surfaces chauff es faire passer l appareil sur le cordon ou d poser des objets lourds ou tranchants sur le cordon e NE JAMAIS d brancher en tirant le cordon Pour d brancher le cordon de la prise agripper la fiche non pas le cordon e NE JAMAIS laisser cet appareil servir de jouet Attention tout particuli rement lorsque l appareil est utilis par ou pr s d enfants e TOUJOURS garder le visage les doigts les cheveux ou toute autre partie du corps ou v tements amples loin de toute ouverture de l appareil ou pi ce mobile e TOUJOURS utiliser l appareil prudemment en nettoyant les escaliers ou lorsque l appareil lui m me est sur l escalier NE J
19. erify all daily and weekly maintenance has been performed Flush clean solution tank and hoses with a mixture of 8 ounces 250 milliliters white vinegar to one gallon 4 liter warm water Pour it into the solution tank turn the machine ON and operate it to completely clean the tank and the spray jets running for 30 seconds should be sufficient This will remove any chemical residue Failure to flush the solution system will result in poor spray patterns and corroded jet spray tips Remove and clean the fine mesh filter in the bottom of the solution tank This filter is mounted externally under the right rear side of the solution tank body To remove the screen for cleaning you must first disconnect the hex nut of the solution hose and then turn the lower half of the filter 1 8 of a turn counterclockwise Remove the lower half of the filter and mesh screen to clean CAUTION If there is any clean solution in the tank it will drain out at this time Reassemble and check for leaks e The intake of the vacuum shoe and the vac shoe must be kept clean and free of any debris or obstructions such as carpet fibers to ensure proper flow of extracted liquids The rear cover plate may be removed to allow for a detailed interior cleaning e Repair or replace any worn or damaged components as needed Mandatory Periodic Maintenance It is mandatory that the following maintenance procedure be performed at the described interval
20. esidue solution into the recovery tank Remove the vac hose which is connected to the vac shoe Pull the clear solution tank hose down and insert it into the vac hose Turn ON the vacuum motor and suction all of the liquid into the recovery tank When the solution tank is empty turn the switches OFF To empty the recovery tank remove the hose from the bracket clamp the hose with your hand and lower or aim the hose in the direction that you want the solution to flow Turn the stopper counterclockwise and remove it unclamp your hand and allow the solution to drain Dispose of the liquids according to your local EPA regulations There is a metal screen cartridge on top of the vacuum tube under the clear dome Remove any residue from the screen to ensure proper operation Store the machine in a dry area Store with brush assembly up Check the drain hose for damage Remove the spray tips 1 4 turn from the spray bar and put them in a glass or plastic container with a solution of 2596 vinegar and water overnight to remove any chemical residue Unplug the machine and inspect the brush assembly paying special attention to the ends of the rollers for buildup of carpet fibers hair or other materials Remove all debris from the brush Failure to remove this material could overload the circuit breaker jam and break the belt obstruct and damage the bearings or burn out the brush drive motor Weekly Maintenance 25 Hours V
21. i avec un cordon 3 conducteurs et une fiche de branchement masse trois contacts La fiche doit tre branch e dans une prise appropri e install e et mise la terre correctement selon tous les codes et ordonnances locaux Le conducteur vert du cordon est le fil de masse Ne jamais brancher ce fil autre chose que la broche de masse de la fiche de branchement V rifier la plaque signal tique de l appareil pour tre certain que la tension et le cycle indiqu s sont les m mes que la prise lectrique Ne pas essayer de brancher un appareil de 120 volts une prise de 240 volts ou un appareil de 240 volts une prise de 120 volts Si l appareil est fourni avec une fiche de branchement tel qu indiqu dans la figure A plus bas il doit donc tre utilis avec un circuit nominal de 120 volts S il n y a pas de prise mise la terre telle qu indiqu dans la figure A disponible on peut installer un adaptateur tel qu indiqu dans la figure B si la bo te prises est mise la terre S assurer d attacher la patte de mise la terre boucle cosse rigide de couleur verte ou quelque chose de semblable sortant de l adaptateur avec une vis de plaque signal tique de m tal Si l appareil est fourni avec une fiche de branchement tel qu indiqu dans la figure C il doit donc tre utilis avec un circuit nominal de 240 volts Il n y a aucun adaptateur disponible pour cette fiche A FIGURE B FIGURE Sees FIGURE C 115V 60H7 115V
22. ng position push down on the right lever and lock it under the notch Plan your work based upon available electrical outlets Using the bumper wheel located on the right side of the machine align the machine as close to the wall as possible Start at the electrical outlet to which your machine is plugged into clean along the wallboards away from your outlet This helps to avoid running over the cord during operation It is possible to transverse 75 feet the length of your cord away from the wall outlet to which your machine is plugged in Usually areas closest to the walls are the least soiled the speed control can be set at its mid point or turned up to a higher speed The brush shoe and brush head will swing out from the wall if they get too close to the wall This avoids gouging the wallboards or the wall Cross to the other side of the hall or room and work your way back along the opposite wall for as far as the length of the cord will allow It is best to allow for a two inch overlap on each pass to be sure you have covered all of the carpet If time allows after you have completed extracting turn the spray switch OFF then with both the vac switch and brush switches ON make high speed passes over the carpet The high speed vacuuming of the extracted carpet will remove excess moisture speed up the drying time and set the pile leaving a better appearance Empty the recovery tank as needed during operation
23. nk may run dry This will allow air to enter the pump and solution lines causing an air lock in the solution lines The air lock prevents the pump from working properly you must prime the pump e The solution tank should have liquid in it and the in line filter screen should be clean and free of debris e Turn the master switch and spray switch ON e Stand at the side of the machine and depress the pin in the center of the accessory quick disconnect The pump will push solution and air out of the quick connect To purge the solution lines run the pump for 30 seconds or until the solution flows smoothly e Recheck the spray output at the spray jet bar assembly MACHINE OPERATION This machine is very maneuverable and is designed to clean as you move forwards across the carpet Drive the machine to the cleaning site by Turning the master switch to ON squeeze the deadman lever and turn the speed control to get the desired speed Normal Cleaning e Always vacuum the carpet with a vacuum cleaner before extraction We recommend you wear clean tennis shoes or non slip shoes when working with a carpet extractor Street shoes or rubber cushion soled shoes when wet will release absorbed dirt or grease onto the wet carpet and cause re soiling You may need to pre treat spots and heavy traffic lanes before extraction Refer to the Common Stains and Cleaning Treatments chart for examples of types of stains and the
24. otor no motor component parts available requires the removal of the mounting hex nuts and wires to the rectifier and ground wire Adjust the drive belt tension after replacing the motor 2 COMMON STAINS AND CLEANING TREATMENTS TREATMENT METHODS e Remove excess material if the stain is liquid blot excess liquids with a dry cloth or paper towel if the material is a solid remove it by scraping it with a dull edge butter knife e Clean the remaining stain as directed by the chart below Always follow the directions on the container Apply the cleaning material directly to the stain avoid over wetting the carpet or upholstery Remove the loosened stain material with a white absorbent cloth tissue or paper towel e When the carpet is dry gently brush the carpet pile to restore its appearance e Treat unknown stains with a volatile solvent first and follow with other agents as required If you are uncertain of the effect of the cleaning agent on the carpet fiber or dye test on an inconspicuous area first Blood dried Warm detergent Ammonia 3 6 Water Sood et EIE T Urine Liquid detergent Water Vomit Warm detergent Water White vinegar Wine Liquid detergent Ammonia 3 6 Water Vinegar Tomato Juice Liquid detergent TROUBLESHOOTING Symptom Cause Solution No Solution From Spray Tis Uneven Spray Nozze Clean or replace No Solution From Spray Tie On ARS Replace pump Pris OR DU Brush Motor
25. r jet wand is squeezed in the ON position Remove vac hose from vac shoe and attach accessory vac hose cuff to machine vac hose Do not apply water more than twice in one area to prevent excess wetting e Over wetting can damage upholstery and or fabric MACHINE MAINTENANCE Routine maintenance is critical to ensure proper machine operation and cleaning performance Perform all maintenance procedures as follows Always turn OFF all machine switches before performing any maintenance All the switches and the brush and vacuum shoe handle linkages can be accessed by removing the screws securing the switch control panel to the body All motors and pumps located inside the body can be accessed by the following procedures Locate the mounting studs and nuts for the swivel casters Remove only the rear outer nuts This will disconnect the rear of the main body from the chassis Disconnect the tool rod solution hose and accessory hose Lift the rear of the machine body to tilt forward for access the prop rod that holds up the machine is under the solution tank DAILY MAINTENANCE At the end of the day empty all liquids from both the solution and recovery tanks Rinse both tanks with clean water to remove debris and prevent chemical residue build up to prevent odors from building up turn the clear dome sideways this provides an opening to allow the tanks to air dry e The solution tank can be emptied by vacuuming the r
26. solution used to treat the stain Test the cleaner on a small inconspicuous area to make sure it will not damage the carpet fibers Apply appropriate spotter following directions on the container You may apply the pre treat chemicals in a number of ways Use a hand held spray bottle There is room for two bottles of spotting liquid on the shelf at the back of the machine Let the spray sit on the stain for about five minutes soak up excess liquids with a towel Use the accessory spray wand by squeezing the trigger on the spray wand this will draw cleaning solution from the machine s solution tank Do not attempt to pre spray areas that you will not over scrub with the machine within a ten minute time span To operate the machine e Turn the master switch ON e Check the brush and pump for proper operation turn both switches to ON Lower the brush head by moving the left lever to the left and releasing it the brush head will move into position on the carpet Lower the vacuum shoe to the carpet with the right lift lever by moving the lever to the right and releasing it Note You must lift the vacuum shoe when moving this machine in reverse e Squeeze the deadman lever under the control handle in order to propel forward and activate the brush e Turn the speed control to propel the machine at the required speed Note You may also lockdown the vacuum shoe to the carpet for better recovery From the floati
Download Pdf Manuals
Related Search