DS42 Inverter Rotary Vane Pumps
Contents
1. Figure 2 CAUTION Check that your electrical mains voltage corresponds to the range indicated on controller label Connect the pump to the power supply DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 29 78 2 Instructions for Use Use Use There are no special procedures for switching the pump on it needs only to be connected to the electric power by means of the bipolar switch WARNING The pump is designed for operation with neutral or non corrosive fluids It is absolutely forbidden to use potentially explosive or flammable substances 30 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Instructions for Use 2 Maintenance Personnel responsible for pump operation and maintenance must be well trained and must be aware of the accident prevention rules WARNING Death may result from contact with high voltages Always take extreme care and observe the accident prevention regulations in force WARNING When machine is powered take care on account of moving parts and high voltages WARNING If you have to perform maintenance on the pump after a considerable time in operation leave it to cool as temperature of the outer surface may be in excess of 60 C DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 31 78 2 Instructions for Use Maintenance WARNING Always disconnect the power supply to the pump before starting maintenance work Place2. 24 78 0542 Inverter Rotary Vane Pumps 87 900 140 01 A Instructions for Use 2 Storage When transporting and storing the pumps the following environmental requirements should not be exceeded temperature from 20 to 70 C relative humidity 0 95 non condensing DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 25 18 2 Instructions for Use Preparation for Installation Preparation for Installation The pump is supplied in a special protective packing If this shows signs of damage which may have occurred during transport contact your local sales office Total weight of the pack including the pump is approx 13 Kg When unpacking the pump be sure not to drop it and avoid any kind of sudden impact or shock vibration to it Do not dispose of the packing materials in an unauthorized manner The material is 100 6 recyclable and complies with EEC Directive 85 399 Normal exposure to the environment cannot damage the pump Nevertheless it is advisable to keep it closed until itis installed in the system thus preventing any form of pollution by dust The pump is provided with some standard accessories 11 0 cable 320 retention spring 1 extension cable IEC320 26 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Instructions for Use 2 Preparation for Installation Figure 1 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 21 18 2 Instructions for U
3. Source Pump with address 3 in stop status Destination PC 02 83 32 30 35 30 30 30 30 30 30 03 38 37 STX ADDR WINDOW DATA STATUS ETX CRC DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 67 78 3 Technical Information RS 232 Communication Description 202 N R POWER W 206 N R ERROR CODE Bit 7 Rotor blocked Bit 6 shortcircuit Bit b Vdc Overvoltage Bit 4 Motor overtemp Bit 3 Too long starting Bit 2 Controller IGBT Bit 1 Vdc Undervoltage Bit 0 overcurrent 211 N R HEATSINK TEMPERATURE C He lt lt T S 6 m LO E 2307 R TIME CONTROLLER STAND BY 2 H E 68 78 0542 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 382 N R AVERAGE PUMP TEMPERATURE C 402 A R PARAMETER LISTING CRC 406 A R PROGRAM LISTING CODE amp REVISION 407 A R PARAMETER LISTING CODE amp REVISION Operational Limits Tab 8 INPUT VOLTAGE V CONTROLLER STATUS lt 90 Power fail 90 264 Operative gt 264 Power fail DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 69 78 3 Technical Information RS 232 Communication Description Status LED Tab 9 LED STATUS CONTROLLER STATUS Green blinking Stop once every 2 seconds When you switch the controller on an electronic self test is performed during such phase yo
4. DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 45 78 3 Technical Information Transport and Installation Setting the pump in position should be performed as follows Pump laid on the ground There are no special instructions for this type of installation except that the floor should be as flat as possible and suited to bear the weight of the pump it should ideally be a concrete floor and of any accessories mounted on it Note that the pump is stable on its base plate and it should not be necessary to anchor it to the floor with bolts and screws also vibrations to and from the pump are greatly reduced by the use of rubber feet Pump off the ground In this case the user must design a suitable support structure remembering the following points the plane supporting the pump must be perfectly horizontal the structure should be adequately rigid the relevant safety precautions should be applied Note also that the pump should be attached to the supporting structure after replacing the rubber feet with special anti vibration feet which should be screwed to the pump base and to the supporting plane After taking the pump out of its packing case you are advised to make the following checks a Ensure that the pump has not suffered any damage during shipping b Check that there no uncovered or loose parts Preliminary Operations Before starting the pump check for oil level CAUTION Oil must be
5. 0x02 ADDR Unit address 0x80 for RS 232 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 WIN Window a string of 3 numeric character indicating the window number from 000 to 9997 for the meaning of each window see the relevant paragraph COM Command 0x30 to read the window 0x31 to write into the window DATA an alphanumeric ASCII string with the data to be written into the window In case of a reading command this field is not present The field length is variable according to the data type as per the following table Logic L Numeric N Alphanumeric A 10 ETX End of transmission 0x03 CRC XOR of all characters subsequent to lt STX gt and including the lt gt terminator The value is hexadecimal coded and indicated by two ASCII character The addressed SLAVE will respond with an ANSWER whose structure depends from the MESSAGE type When the MESSAGE is a reading command the SLAVE will respond transmitting a string with the same structure of the MESSAGE 0542 Inverter Rotary Vane Pumps 87 900 140 01 A 65 78 3 Technical Information RS 232 Communication Description The controller can answers with the following response types Numeric 6 bytes after a read instruction of a numeric window Alphanumeric 10 bytes after a read instruction of an alphanumeric window ACK 1 byte 0x6 the c
6. Interlock N O Relay contact It is closed as soon as the rotational frequency exceed the threshold defined with window n0 102 plus histerisys defined by window 105 Factory set 62 Hz Start stop If the inverter is managed by remote port it manages the pump starting Connect it to 24V pin 9 to start the pump Low speed If the inverter is managed by remote port it set the pump low speed When it is left open or tied to GND the frequency setting is HIGH SPEED if it is connected to 24V pin 9 the frequency setting is LOW SPEED The controller inputs are 0 24V active high To activate the input related functionally it should be tied to 24Vdc pin a non active state could be obtained either leaving the input not connected or connecting it to GND When active it sources a current less of equal to 6 mA Active state Vinput 2 12V or Isink2 1 6 mA Nonacctive state Vinput x AV or Isinks 0 1 mA DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 61 78 3 Technical Information Pump Electronic Controller Here below there is a typical connection of trhe input to an external system output Customer s Controller um 5 Vdc NPN nur Figure 7 The pump operation is 1 0 signals dependent so you must always plug in the provided mating connector to start the pump Procedure to connect the 1 0 port to an external cable The following picture shows the right procedure
7. Singapore Agilent Technologies Singapore Pte Ltd Vacuum Products Division Agilent Technologies Building 1 Yishun Avenue 7 Singapore 768923 Tel 65 6215 8045 Fax 65 6754 0574 Agilent Technologies Inc 2013 Printed in ITALY 11 2013 Publication Number 87 900 140 01 A Agilent Technologies Southeast Asia Agilent Technologies Sales Sdn Bhd Vacuum Products Division Unit 201 Level 2 uptown 2 2 Jalan 5521 37 Damansara Uptown 47400 Petaling Jaya Selangor Malaysia Tel 603 7712 6106 Fax 603 6733 8121 Taiwan Agilent Technologies Taiwan Limited Vacuum Products Division 3F 20 Kao Shuang Rd Pin Chen City 324 Taoyuan Hsien Taiwan R 0 C Tel 886 34959281 Toll Free 0800 051 342 UK and Ireland Agilent Technologies UK Ltd Vacuum Products Division 6 Mead Road Oxford Industrial Park Yarnton Oxford OX5 1QU UK Tel 44 0 1865 291570 Fax 44 0 1865 291571 Toll free 00 800 234 234 00 Other Countries Agilent Technologies Italia S p A Vacuum Products Division Via F lli Varian 54 10040 Leini Torino Italy Tel 39 011 997 9111 Fax 39 011 997 9350 Toll Free 00 800 234 234 00 Customer Support amp Service NORTH AMERICA Toll Free 800 882 7426 Option 3 vpl ra agilent com EUROPE Toll Free 00 800 234 234 00 vpt customercare agilent com PACIFIC RIM please visit our website for individual office information http www agilent com Wo
8. before reassembling components 0542 Inverter Rotary Vane Pumps 87 900 140 01 A 55 78 3 Technical Information Maintenance Actions Maintenance Actions Maintenance may be seen as the totality of all scheduled and unscheduled maintenance work SCHEDULED MAINTENANCE Maintaining the nominal state of operation Tab 2 Oil level checking Daily before every starting Oil change 8 000 hours light applications Exhaust filter replacement If oil mist at exhaust or yearly Fan cover cleaning 6 months UNSCHEDULED MAINTENANCE Restoring the nominal state of operation The frequency with which repairs are performed depends on the process and presence of substances that shorten pump life dust abrasives solvents water chemically aggressive substances The pump must be cleaned at regular intervals of time Do not clean with Alcohol the plastic or rubber components of the pump 56 78 Use only the strictly necessary amount of lubricant an excess of lubricating oil like when there is none may sometimes compromise proper operation of the pump Only the recommended lubricants or lubricating oils with similar characteristics and known and experimented quality should be used Oil changes must be made with the oil at a sufficiently high temperature after leaving the pump to cool for a few minutes following operation The drain and filler plugs must not be left open any longer than is strictly necessary When performi
9. not addressing in an adequate or timely manner Upon receipt of your Corrective Action Request we will determine the Root Cause of the problem and take the necessary actions to eliminate it You will be contacted by one of our employees who will review the problem with you and update you with the second part of the same form on our actions Your business is very important to us Please take the time and let us know how we can improve Sincerely AC Giampaolo LEVI Vice President and General Manager Agilent Vacuum Products Division Note Fax or mail the Customer Request for Action see backside page to Agilent Vacuum Products Division Torino Quality Assurance or to your nearest Agilent representative for onward transmission to the same address CUSTOMER REQUEST FOR CORRECTIVE PREVENTIVE IMPROVEMENT ACTION TO AGILENT VACUUM PRODUCTS DIVISION TORINO QUALITY ASSURANCE FAX N XXXX 011 9979350 ADDRESS AGILENT TECHNOLOGIES ITALIA S p A Vacuum Products Division Via F lli Varian 54 10040 Lein TO Italy E MAIL vpd qualityassurance_pdl ext agilent com NAME COMPANY FUNCTION ADDRESS TEL N FAX N E MAIL PROBLEM SUGGESTION REFERENCE INFORMATION model n serial n ordering information time to failure after installation etc CORRECTIVE ACTION PLAN ACTUATION LOG N by AGILENT VPD XXX Code for dialing Italy from your country es 01139 from USA 0013
10. oil reaches its working temperature There are no special instructions for normal operation of the pump which is delivered to you after completion of a runningin cycle in the factory To allow the pump starting you have to wire properly the interlock pins by connecting the mating connector provided with the pump For repetitive work cycles with brief time intervals in between it is better not to stop the pump 50 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Stopping the Pump There are no special procedures for switching the pump off it needs only to be disconnected from the electric power by means of the bipolar switch When the pump is stopped the anti suckback device makes it possible to maintain vacuum in the vessel connected on the inlet flange of the pump DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 51 78 3 Technical Information Safety Rules Safety Rules Personnel responsible for pump operation and maintenance must be well trained and must be aware of the accident prevention rules The accident prevention precautions contained in this section must be respected at all times during operation and maintenance of the pump to avoid damage to operators and to the pump These precautions are provided in the form of WARNING and CAUTION notes Operating procedures technical information and precautions which if not respected and or implemented correctly may cause bod
11. out contain dust it is advisable to insert a dust filter before the inlet flange 48 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Connections to the Inlet and Exhaust Flanges NOTE When the gases to be pumped out contain large quantities of vapor it is advisable to include a condense separator before the inlet flange To make best use of the pump s capacity use only short straight piping with a diameter not smaller than that of the inlet flange NOTE If rigid piping is used it is good practice to use a flexible joint in order to avoid undue forcing of the connection on the pump The exhaust duct must be connected to a pipe that will take away the pumped out gases NOTE An internal oil mist eliminator avoids pollution of the surrounding atmosphere by the oil present in the exhaust duct during pump operation CAUTION Never block the pump exhaust line This would cause overpressure in the casing with the risk of breaking the oil tank DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 49 78 3 Technical Information Starting and Running the Pump Starting and Running the Pump WARNING The pump is designed for operation with neutral or non corrosive fluids It is absolutely forbidden to use potentially explosive or flammable substances If the pump is started with cold oil initially more than normal noise will be heard this will last for a few minutes only until the
12. specifically engineered to provide superior performance in high speed direct drive mechanical pumps These precisely distilled fluids 100 solvent refined neutral paraffinic oil deliver lower base pressure capability faster pump down cycles and reduced maintenance requirements on both the pump and the fluid Itis absolutely necessary to continue using the lubricants initially used to fill the tank If this is not possible for organizational or business reasons use only products with the same characteristics as the previous oils Only use of lubricants of suitable quality will guarantee safe operation of the pumps Mineral oils and the PFPE oil are incompatible To change from one type to another the pump must be stripped down completely and all parts washed carefully to eliminate all oil residues If you expect to have to use other lubricants first find out if the two products are compatible In cases of doubt the lubricant used up to that time must be flushed out by way of a pump flushing procedure To avoid the risk of contaminating the oil absolute cleanliness of the pump and surrounding area must be ensured during the lubrication procedures 58 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Pump Electronic Controller 1 0 port P1 Status LED Figure 6 Technical Specifications Input voltage 100V 240Vac 10 50 60 Hz Max input power 100 Vac 3 0
13. taxable 2 PRODUCT IDENTIFICATION Product Description Agilent P N Agilent S N Original Purchasing Reference 3 TYPE OF RETURN Choose one from each row and supply Purchase Order if requesting a billable service 3A a Non Billable Billable emm New hard copy must be submitted with this form 3B Exchange Repair Upgrade Consignment Demo Calibration Evaluation Return for Credit 4 HEALTH and SAFETY CERTIFICATION AGILENT TECHNOLOGIES CANNOT ACCEPT ANY PRODUCTS CONTAMINATED WITH BIOLOGICAL OR EXPLOSIVE HAZARDS RADIOACTIVE MATERIAL OR MERCURY AT ITS FACILITY Call Agilent Technologies to discuss alternatives if this requirement presents a problem The equipment listed above check one HAS NOT pumped or been exposed to any toxic or hazardous materials OR L HAS pumped or been exposed to the following toxic or hazardous materials If this box is checked the following information must also be filled out Check boxes for all materials to which product s pumped or was exposed L Corrosive Reactive L Flammable Explosive Biological Radioactive List all toxic hazardous materials Include product name chemical name and chemical symbol or formula NOTE If a product is received at Agilent which is contaminated with a toxic or hazardous material that was not disclosed the customer will be held responsible for all costs incurred to ensure the safe handling o
14. to connect a cable to the I O port connector shielded cable of 30 m maximum length has to be utilized for both serial and I O port connection Take care to have a good contact soldered between the metallic connector case and the external shield of the cable Moreover this connection has to be assured at least on the controller side 62 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Pump Electronic Controller Figure 8 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 63 78 3 Technical Information RS 232 Communication Description RS 232 Communication Description The RS 232 interface is available on the I O connector Communication Format 8 data bit no parity 1 stop bit baud rate 600 1200 2400 4800 9600 19200 38400 programmable Communication Protocol The communication protocol is a MASTER SLAVE type where Host MASTER Controller SLAVE The communication is performed in the following way 1 the host MASTER send a MESSAGE CRC to the controller SLAVE 2 the controller answer with an ANSWER CRC to the host The MESSAGE is a string with the following format lt STX gt lt ADDR gt lt WIN gt lt COM gt lt DATA gt lt ETX gt lt CRC gt Where When a data is indicated between two quotes 7 it means that the indicated data is the corresponding ASCII character 64 78 lt STX gt Start of transmission
15. 0542 Inverter Rotary Vane Pumps Model 3700 60000 Notice de Mode D Emploi User Manual 87 900 140 01 A 11 2013 E Agilent Technologies Notices Agilent Technologies Inc 2012 No part of this manual may be reproduced in any form or by any means including electronic storage and retrieval or translation into a foreign language without prior agreement and written consent from Agilent Technologies Inc as governed by United States and international copyright laws Manual Part Number Publication Number 87 900 140 01 A Edition Edition 11 2013 Printed in ITALY Agilent Technologies Italia S p A Vacuum Products Division Via F lli Varian 54 10040 Leini TO ITALY Warranty The material contained in this document is provided as is and is subject to being changed without notice in future editions Further to the maximum extent permitted by applicable law Agilent disclaims all warranties either express or implied with regard to this manual and any information contained herein including but not limited to the implied warranties of merchantability and fitness for a particular purpose Agilent shall not be liable for errors or for incidental or consequential damages in connection with the furnishing use or performance of this document or of any information contained herein Should Agilent and the user have a separate written agreement with warranty terms covering the material in this doc
16. 0542 Inverter Rotary Vane Pumps layout 42 18 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Figure 5 0542 Inverter Rotary Vane Pumps dimensions 0542 Inverter Rotary Vane Pumps 87 900 140 01 A 43 18 3 Technical Information Safety Precautions Safety Precautions Always carry the pump by means of the ring bolt provided pump must be set in position taking the upmost care in order to avoid accidental falls WARNING In case of a need to handle the pump after a period of operation it must be left to cool first as the external surface temperature may be in excess of 60 C 44 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Transport and Installation The pumps are shipped to the customer inside cardboard boxes Total weight of the pack including the pump is about 17 Kg The case must be handled with care using appropriate lifting equipment CAUTION When moving the case ensure that it is securely bound to the lifting equipment and that the equipment is strong enough to support the weight The pump s working environment is a traditional industrial environment Naturally sites with corrosive vapors or excessive heat are best avoided Room temperature should ideally be between 12 C and 40 C If the temperature is not inside this range consult Agilent technical service for the changes required
17. 5 305VA 221W 240 Vac 1 34Aac 331Va 215 W Output voltage 240 Vrms 3ph Max frequency 100 Hz factory setting Starting phase maximum power 200 W max 30 minutes DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 59 78 3 Technical Information Pump Electronic Controller Normal Operation maximum power 150 W Maximum room temperature 40 C Protection level IP 20 Touch current ca 1 1 mA 264Vac 60 150 W 100 Hz nrush current 120Vac 20A 240Vac 40A mark Tab 3 EN61326 1 2006 Elctrical equipmnt for measurement control and laboratory use Requirements Emission Class A 10dB Immunity industrial levels according to Tab 2 EN61000 4 2 EN61000 4 8 EN61000 4 3 EN61000 4 11 EN61000 4 4 EN61000 4 12 CSA mark EN61010 1 2001 Safety requirements for electrical equipment for measurement control laboratory use Before connecting the IEC320 mains cable install the Retention Spring provided with the DS42 Inverter Rotary Vane Pump The Retention Spring has to be fastened to IEC320 connector lateral screws Use the Retention Spring to secure the mains cable into the IEC320 socket 60 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Input Output Communications P1 1 0 Analog signals RS232 in one port Tab 4 PIN N SIGNAL NAME IN OUT 1 Interlock Status N O relay contact out
18. 9 from Japan etc Agilent Technologies Vacuum Products Division Instructions for returning products Dear Customer Please follow these instructions whenever one of our products needs to be returned 1 2 3 4 5 6 7 Complete the attached Request for Return form and send it to Agilent Technologies see below taking particular care to identify all products that have pumped or been exposed to any toxic or hazardous materials After evaluating the information Agilent Technologies will provide you with a Return Authorization RA number via email or fax as requested Note Depending on the type of return a Purchase Order may be required at the time the Request for Return is submitted We will quote any necessary services evaluation repair special cleaning eg Important steps for the shipment of returning product e Remove all accessories from the core product e g inlet screens vent valves e Prior to shipment drain any oils or other liquids purge or flush all gasses and wipe off any excess residue e f ordering an Advance Exchange product please use the packaging from the Advance Exchange to return the defective product e Sealthe product in a plastic bag and package product carefully to avoid damage in transit You are responsible for loss or damage in transit Agilent Technologies is not responsible for returning customer provided packaging or containers Clearly label package wi
19. Use Disposal 34 18 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A o e e e ee 3 DS42 Inverter Rotary Vane Pumps Technical Information Section 37 Technical Description 37 Vacuum Seals 39 Anti Suckback Device 40 Technical Data 4 Dimensions 42 Safety Precautions 44 Transport and Installation 45 Preliminary Operations 46 Section Il 48 Connection to the Electric Supply 48 Connections to the Inlet and Exhaust Flanges 48 Starting and Running the Pump 50 Stopping the Pump 51 Safety Rules 52 Warning Notes 53 Caution Notes 55 Maintenance Actions 56 Pump Electronic Controller 59 Technical Specifications 59 Input Output Communications 61 P1 1 0 Analog signals RS232 one port 61 Procedure to connect the 1 0 port to an external cable 62 Original Instructions GE Agilent Technologies 35 78 3 Technical Information Disposal RS 232 Communication Description 64 Communication Format 64 Communication Protocol 64 Examples 66 Window Meanings 68 Operational Limits 69 Status LED 70 Electronic Self Test 70 Rotor Lock Test 70 Accessories 71 36 78 0542 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Section Technical Description The DS42 Inverter Rotary Vane Pumps are rotary vane pumps oil sealed driven by a three phase electric motor Figure 3 These vacuum pumps are suitable for pumping non corrosive gases The main features are all parts in
20. a special warning signs over the power supply breaker switch MACHINE UNDERGOING MAINTENANCE DO NOT POWER ON When finished remove the safety warning WARNING Do not change the oil immediately after stopping the machine as the oil temperature may still be high Before returning the pump to the constructor for repairs the Health and Safety Certification sheet attached to this instruction manual must be filled in and sent to the local sales office A copy of the sheet must be inserted in the pump package before shipping If a pump is to be scrapped it must be disposed of in accordance with the specific national standards 32 18 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Instructions for Use 2 Disposal Meaning of the WEEE logo found in labels The following symbol is applied in accordance with the EC WEEE Waste Electrical and Electronic Equipment Directive This symbol valid only in countries of the European Community indicates that the product it applies to must NOT be disposed of together with ordinary domestic or industrial waste but must be sent to a differentiated waste collection system The end user is therefore invited to contact the supplier of the device whether the Parent Company or a retailer to initiate the collection and disposal process after checking the contractual terms and conditions of sale 0542 Inverter Rotary Vane Pumps 87 900 140 01 A 33 18 2 Instructions for
21. arantir la s curit de l op rateur pendant l utilisation de l appareil Des ren seignements plus d taill s se trouvent dans l appendice Technical Information DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Mode d emploi 1 Cette notice utilise les signes conventionnels suivants Les messages d avertissement attirent l attention de l op rateur sur une proc dure ou une man uvre sp ciale dont la mauvaise ex cution risque de provoquer de graves l sions werd iiM Les messages d attention apparaissent avant certaines proc dures dont le non respect pourrait endommager s rieusement l appareil Les notes contiennent des renseignements importants isol s du texte DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 9 78 1 Mode d emploi Indications g n rales Symboles utilis s Les symboles suivants sont utilis s dans toutes les illustrations alis Vanne de ballast gaz de ballast 087 Bride d aspiration d EIS i Remplissage fluide de travail Remplissage fluide de travail de travail Bride de vidange de Bride de vidange 10 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Mode d emploi 1 Emmagasinage Pendant le transport et l emmagasinage des pompes veiller respecter les conditions environnementales suivantes temp rature de 20 C 70 C humidit relative 0 95 sans conde
22. as Protect all the clearances of connection points with suitable plastic caps and cover the machined surface areas of all parts stripped down until they are put back on the pump again 54 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Caution Notes a Before putting the pump back into operation after a breakdown inspect it and check carefully for any other signs of damage b Use only tools that are in perfect working order and specially designed for the job use of inappropriate or ineffective tools may cause serious damage Perform repairs in clean and where possible dust free areas Protect all the clearances of connection points with suitable plastic caps and cover the machined surface areas of all parts stripped down until they are put back on the pump again d Always check the lubricant and that it is properly distributed through the pump inadequate lubrication may damage the pump seriously e Give the parts some form of marking as you strip them down to ensure that you reassemble them again in the proper order f Check that there are no scratches or grooves on the machined shafts in their seats inside the pump or on machine ground surfaces Slight scratches and abrasions may be eliminated with very fine emery paper or by a little light grinding g Before putting a group together always spread a little oil over inner parts and mating surfaces Replace all seals with original spare parts
23. de Courtaboeuf B P 12 91941 Les Ulis cedex France Tel 33 0 1 69 86 38 84 Fax 33 0 1 69 86 29 88 Toll free 00 800 234 234 00 Germany and Austria Agilent Technologies Vacuum Products Division Alsfelder Strasse 6 Postfach 11 14 35 64289 Darmstadt Germany Tel 49 0 6151 703 353 Fax 49 0 6151 703 302 Toll free 00 800 234 234 00 Sales and Service Offices India Agilent Technologies India Pvt Ltd Vacuum Product Division G01 Prime corporate Park 230 231 Sahar Road Opp Blue Dart Centre Andheri East Mumbai 400 099 India Tel 91 22 30648287 8200 Fax 91 22 30648250 Toll Free 1800 113037 Italy Agilent Technologies Italia S p A Vacuum Products Division Via F lli Varian 54 10040 Leini Torino Italy Tel 39 011 997 9111 Fax 39 011 997 9350 Toll Free 00 800 234 234 00 Japan Agilent Technologies Japan Ltd Vacuum Products Division 8th Floor Sumitomo Shibaura Building 4 16 36 Shibaura Minato ku Tokyo 108 0023 Japan Tel 81 3 5232 1253 Fax 81 3 5232 1710 Toll Free 0120 655 040 Korea Agilent Technologies Korea Ltd Vacuum Products Division Shinsa 2nd Bldg 2F 966 5 Daechi dong Kangnam gu Seoul Korea 135 280 Tel 82 2 3452 2452 Fax 82 2 3452 2451 Toll Free 080 222 2452 Mexico Agilent Technologies Vacuum Products Division Concepcion Beistegui No 109 Col Del Valle C P 03100 Mexico D F Tel 52 5 523 9465 Fax 52 5 523 9472
24. direct contact with the fluid pumped are free of copper alloys all materials are carefully selected to provide extended life 0542 Inverter Rotary Vane Pumps 87 900 140 01 A 37 78 3 Technical Information Technical Description due to its design features and low number of gaskets the pump requires little maintenance disassembly and reassemble are easy and require minimal time The oil guarantees perfect sealing of the discharge valves enters the pump to ensure lubrication and sealing of the parts inside facilitates heat dissipation and reduces pump noise The pump is equipped with a special anti suckback device which automatically isolates the vacuum system when the pump stops This avoids rises in pressure or oil flow in the vacuum system while air is allowed back into the stator chambers The air entering the pump after the anti suckback device has closed prevents the oil in the casing from filling the stator chambers 38 78 0542 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Vacuum Seals A special feature of this pump is the low number of gaskets that are employed The seals in the circuit are obtained by means of VITON gaskets Sealing of the rotor shaft is guaranteed by a rotating gasket with dust guard lip The suction flange and duct are sealed by mean of OR gaskets DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 39 78 3 Technical Information Anti Suckback Device Ant
25. et ou utiliser la pompe dans des milieux expos s aux agents atmosph riques pluie gel neige des poussi res des gaz agressifs ainsi que dans des milieux explosifs ou risque lev d incendie Pendant le fonctionnement il est n cessaire de respecter les conditions environnementales suivantes Temp rature de 12 C 40 Humidit relative 0 95 sans condensation AVERTISSEMENT Pour prot ger contre les court circuits ou les surintensit s il faut installer un disjoncteur automatique sur la ligne d alimentation principale vers les dispositifs Agilent de 10A de capacit ATTENTION Garantissez la pr sence d un espace libre de 20 cm minimum autour de la pompe pour permettre une libre circulation de l air ATTENTION Avant toute utilisation de la pompe v rifier le niveau de l huile 14 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Mode d emploi 1 AVERTISSEMENT Avant toute autre op ration retirer les bouchons de protection plac s sur les brides d aspiration et de vidange En cas de mise en marche inopin e de l appareil l air contenu l int rieur de la pompe peut les projeter contre l op rateur et le blesser AVERTISSEMENT Pendant l installation faire tr s attention ce que la bride d aspiration soit reli e la chambre vider et que la bride de vidange ne soit pas bouch e voir la figure ci apr s La pompe ne doit pa
26. f the product and is liable for any harm or injury to Agilent employees as well as to any third party occurring as a result of exposure to toxic or hazardous materials present in the product Print Name Authorized Signature Date 5 FAILURE INFORMATION Failure Mode REQUIRED FIELD See next page for suggestions of failure terms Detailed Description of Malfunction Please provide the error message Application system and model understand and agree to the terms of Section 6 Page 3 3 Print Name Authorized Signature Pg 2 3 Agilent Technologies Vacuum Products Division Request for Return Form Health and Safety Certification Please use these Failure Mode to describe the concern about the product on Page 2 TURBO PUMPS and TURBO CONTROLLERS APPARENT DEFECT MALFUNCTION POSITION PARAMETERS Does not start Noise Vertical Power Rotational Speed Does not spin freely Vibrations Horizontal Current Inlet Pressure Does not reach full speed Leak Upside down Temp 1 Foreline Pressure Mechanical Contact vertemperature Other Temp 2 Purge flow Cooling defective Clogging OPERATING TIME 10 PUMPS CONTROLLERS VALVES COMPONENTS Bad feedthrough Poor vacuum Main seal leak Bellows leak Vacuum leak High voltage problem Solenoid failure Damaged flange Error code on display Other Da
27. form ment aux r glementations nationales en la mati re DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 19 78 1 Mode d emploi Mise au rebut Mise au rebut 20 78 Signification du logo WEEE figurant sur les tiquettes Le symbole ci dessous est appliqu conform ment la directive CE nomm e WEEE Ce symbole uniquement valide pour les pays de la Communaut europ enne indique que le produit sur lequel il est appliqu NE doit PAS tre mis au rebut avec les ordures m nag res ou les d chets industriels ordinaires mais passer par un syst me de collecte s lective Apr s avoir v rifi les termes et conditions du contrat de vente l utilisateur final est donc pri de contacter le fournisseur du dispositif maison m re ou revendeur pour mettre en uvre le processus de collecte et mise au rebut DS42 Inverter Rotary Vane Pumps 87 900 140 01 A DS42 Inverter Rotary Vane Pumps Instructions for Use General Information 22 Symbols used 24 Storage 25 Preparation for Installation 26 Installation 28 Use 30 Maintenance 31 Disposal 33 Original Instructions GEB Agilent Technologies 21 78 2 Instructions for Use General Information General Information 22 18 This equipment is destined for use by professionals The user should read this instruction manual and any other additional information supplied by Agilent before operating the equipment Agilent will not be held responsible f
28. i Suckback Device The pump is equipped with a special anti suckback device to avoid air pressure rises and or oil back flow towards the evacuated vessel when the pump is switched off The device includes some special features namely drive obtained avoiding any form of contamination of the inlet duct by fluids oil and or air Thanks to this when the pump is started again the pumpdown to vacuum conditions is extremely fast as these contaminants are not present and no degassing is therefore required 40 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Technical Data Th The following table lists the main technical data of the DS42 Inverter Rotary Vane Pumps Tab 1 TECHNICAL DATA Hz Units Value FREE AIR DISPLACEMENT 50 l min m3 h 38 2 3 E m E e E E Aper BALLAST on SS 62 EG Se E n a ee n EE de a e eee o WEIGHT Kg 13 e uu LEE T 2 22 T T According to PNEUROP 6602 At ultimate total pressure 20 C 68 F room temperature DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 41 78 3 Technical Information Technical Data Dimensions The following figure shows the pumps layout and dimensions Inlet flange Electronic controller Outlet flange Electric motor Oil level indicator Pumping block Figure 4
29. ing machines taking care to dry all the cleaned parts at temperatures under 100 C in order to eliminate residual moisture f Prolonged overloads or breakdowns may cause the electric motor to overheat and to release noxious smoke remove the power immediately as a precaution and do not approach the pump at least until you have provided ventilation to drive out the smoke Take care not to breathe in the fumes remaining inside the pump in the course of repair work g In case of fire do not throw water on the pump Switch the power off and use C0 extinguishers h Carefully inspect the flanges to ensure that there is no dust oil dirt or defects of the mating surfaces before making the required connections i Ensure that all joints and couplings are locked correctly before starting the pump again after repair work DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 53 18 3 Technical Information Warning Notes j Do not wear any objects that may become entangled in the mechanisms and or act as conductors chains bracelets etc Ensure that the tools to be used are in perfect working condition and have insulating grips where necessary Check that the insulating material of the cables and that the conductors of the test equipment do not show any signs of damage Do not replace the oil immediately after stopping the machine as the oil may still be at high temperature m Perform repairs in clean and where possible dustfree are
30. maged sealing area Other LEAK DETECTORS INSTRUMENTS Cannot calibrate No zero high backround Gauge tube not working Display problem Vacuum system unstable Cannot reach test mode Communication failure Degas not working Failed to start Other Error code on display Other SCROLL AND ROTARY VANE PUMPS DIFFUSION PUMPS Pump doesn t start Noisy pump describe Heater failure Electrical problem Doesn t reach vacuum Over temperature Doesn t reach vacuum Cooling coil damage Pump seized Other Vacuum leak Other Section 6 ADDITIONAL TERMS Please read the terms and conditions below as they apply to all returns and are in addition to the Agilent Technologies Vacuum Product Division Products and Services Terms of Sale e Customer is responsible for the freight charges for the returning product Return shipments must comply with all applicable Shipping Regulations IATA DOT etc and carrier requirements e Customers receiving an Advance Exchange product agree to return the defective rebuildable part to Agilent Technologies within 15 business days Failure to do so or returning a non rebuildable part crashed will result in an invoice for the non returned non rebuildable part e Returns for credit toward the purchase of new or refurbished Products are subject to prior Agilent approval and may incur a restocking fee Please reference the original purchase order number e Units returned for evaluati
31. nd Running the Pump 50 Stopping the Pump 51 Safety Rules52 Warning Notes 53 Caution Notes 55 Maintenance Actions 56 Lubricants 58 Pump Electronic Controller 59 RS 232 Communication Description 64 Accessories 71 6 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A DS42 Inverter Rotary Vane Pumps Mode d emploi Indications g n rales 8 Symboles utilis s 10 Emmagasinage 11 Preparation pour l installation 12 Installation 14 Utilisation 17 Maintenance 18 Mise au rebut 20 Traduction de la mode d emploi originale E Agilent Technologies 7 78 1 Mode d emploi Indications g n rales Indications g n rales 8 78 Cet appareil a t concu en vue d une utilisation professionnelle Il est conseill l utilisateur de lire attentivement cette notice ainsi que toute autre information fournie par Agilent avant de l utiliser Agilent d cline toute responsabilit en cas de non respect total ou partiel des instructions fournies d utilisation in correcte de la part du personnel non form d op rations non autoris es ou d un emploi contraire aux r glementations nationales sp cifiques Les 0542 Inverter Rotary Vane Pumps sont des pompes rotatives deux tages tages palettes tanches en bain d huile actionn es par un moteur lectrique triphas Ces pompes haut vide sont adapt es au pompage de gaz non corrosifs Les paragraphes suivants fournissent toute l information n cessaire pour g
32. ng maintenance look out for all signals that may precede a breakdown in particular traces of corrosion DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 oil leaks slack joints or couplings Maintenance technicians must be aware of all applicable national directives concerning accident prevention during work on motor driven pumps and should know how to apply them have read and understood all the sections on Safety Rules be familiar with the essential design features and operation of the pump know how to use and consult the pump documentation beconcerned about proper operation of the pump make a note of any irregularities in operation of the pump and take the necessary action where appropriate Use original spare parts wherever possible and repair a broken part as best as possible on site or send it back to the manufacturer for repairs For all problems arising or to order spare parts refer to our service department Agilent Technologies Italia S p A Vacuum Products Division Via Varian 54 10040 Leini Torino Italy Tel 39 011 997 9111 Fax 39 011 997 9350 Toll Free 00 800 234 234 00 0542 Inverter Rotary Vane Pumps 87 900 140 01 A 57 18 3 Technical Information Lubricants Lubricants The recommended lubricating oil is the Agilent Rotary Vane Fluid DS45 Type The Rotary Vane Fluid DS45 Type is a general purpose mechanical pump fluid
33. nsation DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 11 78 1 Mode d emploi Preparation pour l installation Preparation pour l installation La pompe est fournie dans un emballage de protection sp cial si l on constate des marques de dommages pouvant s tre produites pendant le transport contacter aussit t le bureau de vente local Le poids total de l emballage avec la pompe est d environ 13 kg maximum Pendant l op ration d ouverture de l emballage veiller tout particuli rement ne pas laisser tomber la pompe et ne lui faire subir aucun choc ni aucune vibration Ne pas jeter l emballage dans la nature Le mat riel est enti rement recyclable et il est conforme la directive CEE 85 399 en mati re de protection de l environnement La pompe ne peut tre endommag e en restant simplement expos e l atmosph re Il est de toute facon conseill de la garder dans son emballage jusqu au moment de sa mise en place sur le syst me afin d viter toute pollution due la poussi re La pompe est quip e de certains accessoires standard 1 cable de Entr e Sortie 1 0 Ressort de maintien pour prise IEC320 1 cable d extension IEC320 12 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Mode d emploi 1 Preparation pour l installation Figure 1 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 13 78 1 Mode d emploi Installation Installation Ne pas installer
34. ommand execution has been successfully completed Unknown 1 byte 0x32 the specified window in the command is Window not a valid window Data Type Error 1 byte 0x33 the data type specified in the command Logic Numeric or Alphanumeric is not accorded with the specified Window Out of Range 1 byte 0x34 the value expressed during a write command is out of the range value of the specified window Win Disabled 1 byte 0x35 the specified window is Read Only or temporarily disabled for example you can t write the Soft Start when the Pump is running Examples Command START Source PC Destination Pump 02 80 30 30 30 31 31 03 42 33 STX ADDR WINDOW WR ON ETX CRC 66 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Source Pump Destination PC 02 80 06 03 38 35 STX ADDR ACK ETX CRC Command STOP Source PC Destination Pump 02 80 30 30 30 31 30 03 42 32 STX ADDR WINDOW WR OFF ETX CRC Source Pump Destination PC 02 80 06 03 38 35 STX ADDR ACK ETX CRC Command READ PUMP STATUS Source PC Destination Pump with address 3 02 83 32 30 35 30 03 38 37 STX ADDR WINDOW RD ETX CRC
35. on will be evaluated and a quote for repair will be issued If you choose to have the unit repaired the cost of the evaluation will be deducted from the final repair pricing A Purchase Order for the final repair price should be issued within 3 weeks of quotation date Units without a Purchase Order for repair will be returned to the customer and the evaluation fee will be invoiced e Special Cleaning fee will apply to all exposed products per Section 4 of this document e f requesting a calibration service units must be functionally capable of being calibrated Pg 3 3 United States Agilent Technologies Vacuum Products Division 121 Hartwell Avenue Lexington MA 02421 USA Tel 1 781 861 7200 Fax 1 781 860 5437 Toll Free 1 800 882 7426 Benelux Agilent Technologies Netherlands B V Vacuum Products Division Herculesweg 8 4338 PL Middelburg The Netherlands Tel 31 118 671570 Fax 31 118 671569 Toll Free 00 800 234 234 00 Canada Central coordination through Agilent Technologies Vacuum Products Division 121 Hartwell Avenue Lexington MA 02421 USA Tel 1 781 861 7200 Fax 1 781 860 5437 Toll Free 1 800 882 7426 China Agilent Technologies China Co Ltd Vacuum Products Division No 3 Wang Jing Bei Lu Chao Yang District Beijing 100102 China Tel 86 10 6439 7718 Toll Free 800 820 6556 France Agilent Technologies France Vacuum Products Division 7 Avenue des Tropiques Z A
36. or any events occurring due to non compliance even partial with these instructions improper use by untrained persons non authorized interference with the equipment or any action contrary to that provided for by specific national standards The 0542 Inverter Rotary Vane Pumps are double stage rotary vane pumps oil sealed driven by a three phase electric motor These high vacuum pumps are suitable for pumping non corrosive gases The following paragraphs contain all the information necessary to guarantee the safety of the operator when using the equipment Detailed information is supplied in the appendix Technical Information DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Instructions for Use 2 This manual uses the following standard protocol WARNING The warning messages are for attracting the attention of the operator to a particular procedure or practice which if not followed correctly could lead to serious injury WP The caution messages are displayed before procedures which if not followed could cause damage to the equipment The notes contain important information taken from the text DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 23 18 2 Instructions for Use General Information Symbols used The following symbols are used consistently throughout in all illustration n Gas Ballast valve Suction Flange i Filling up operating fluid Exhaust Flange
37. poured into the casing through the special threaded plughole and NOT through the suction line 46 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 WARNING Take out the protective caps on the suction and exhaust flanges before doing anything else In the event of an accidental start up the air inside the pump could violently expel the protective caps and harm the operator DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 47 78 3 Technical Information Section Il Section II Connection to the Electric Supply CAUTION It is recommended to connect the pump to the power supply through a dedicated safety switch on the main electrical panel of the installation or in proximity of the power supply connection point WARNING The pump must be installed in a way that allows an easy interruption of the line voltage Power supply cord The correct cable for electrical wiring is a three wires Ph N Earth cable The wire section has to be at least 0 75 mm2 AWG18 Connections to the Inlet and Exhaust Flanges Remove the protective caps from both flanges Connect the system to be evacuated to the inlet flange using a centering ring with OR and a locking collar For guaranteed reliable sealing use an OR gasket in Perbunan or Viton The inlet duct is equipped with a sieve filter preventing solid particles from entering and damaging the pump When the gases to be pumped
38. rldwide Web Site Catalog and Order On line www agilent com Representative in most countries 12 10
39. s tre utilis e comme un compresseur La pression maximale l int rieur du r servoir d huile ne doit pas d passer 1 5 bar abs Le non respect de ces pr cautions peut entrainer un danger pour l op rateur et endommager la machine Bride d aspiration Bride de vidange Figure 2 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 15 78 1 Mode d emploi Installation Parti p Contr ler que la tension d alimentation correspond la gamme de tensions indiqu es sur la plaquette du contr leur Brancher la pompe la source d alimentation 16 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Mode d emploi 1 Utilisation La mise en marche de la pompe ne requiert aucune man uvre particuli re il suffit de la brancher l alimentation lectrique et d actionner l interrupteur bipolaire AVS TRS SS La pompe a t con ue pour fonctionner avec des fluides neutres ou non corrosifs L emploi de substances potentiellement explosives ou inflammables est strictement interdit DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 17 78 1 Mode d emploi Maintenance Maintenance Le personnel charg de la conduite et de la maintenance de la pompe doit avoir la formation n cessaire et poss der une connaissance approfondie des normes de pr vention des accidents du travail AVERTISSEMENT Les hautes tensions peuvent entrainer la mort par contact Veiller a toujours op rer avec le maxim
40. se Installation Installation Do not install or use the pump in an environment exposed to atmospheric agents rain snow ice dust aggressive gases or in explosive environments or those with a high fire risk During operation the following environmental conditions must be respected temperature from 12 C to 40 C relative humidity 0 95 non condensing Protect against short circuits and overload by installing on Agilent Device electrical main line an automatic circuit breaker of 10A capacity CAUTION Assure a free space all around the pump at minimum of 20cm to allow proper air circulation Before starting the pump check the oil level WARNING Take out the protective caps on the suction and exhaust flanges before doing anything else In the event of an accidental start up the air inside the pump could violently expel the protective caps and harm the operator 28 18 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Instructions for Use 2 WARNING During installation pay maximum attention that the suction flange is connected to the vacuum chamber and the exhaust flange is not closed see the following figure The pump must not be used as a compressor Maximum pressure inside the oil container must not exceed 1 5 bar abs Non observance of these precautions may be dangerous for the machine and the operator Inlet Flange Outlet Flange
41. sult in damage to the product or loss of important data Do not proceed beyond a CAUTION notice until the indicated conditions are fully understood and met A WARNING notice denotes a hazard It calls attention to an operating procedure practice or the like that if not correctly performed or adhered to could result in personal injury or death Do not proceed beyond a WARNING notice until the indicated conditions are fully understood and met DS42 Inverter Rotary Vane Pumps 87 900 140 01 A DS42 Inverter Rotary Vane Pumps DS42 Inverter Rotary Vane Pumps 3 18 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A DS42 Inverter Rotary Vane Pumps 4 18 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Contents 1 3 Contents Mode d emploi 7 Indications g n rales 8 Emmagasinage 11 Preparation pour l installation 12 Installation 14 Utilisation 17 Maintenance 18 Mise au rebut 20 Instructions for Use 21 General Information 22 Storage 25 Preparation for Installation 26 Installation 28 Use 30 Maintenance 31 Disposal 33 Technical Information 35 Section 37 Technical Description 37 0542 Inverter Rotary Vane Pumps 87 900 140 01 A 5 78 Contents Vacuum Seals 39 Anti Suckback Device 40 Technical Data 41 Safety Precautions 44 Transport and Installation 45 Section l 48 Connection to the Electric Supply48 Connections to the Inlet and Exhaust Flanges 48 Starting a
42. th RA number Using the shipping label provided will ensure the proper address and RA number are on the package Packages shipped to Agilent without a RA clearly written on the outside cannot be accepted and will be returned Return only products for which the RA was issued Product being returned under a RA must be received within 15 business days Ship to the location specified on the printable label which will be sent along with the RA number as soon as we have received all of the required information Customer is responsible for freight charges on returning product Return shipments must comply with all applicable Shipping Regulations IATA DOT etc and carrier requirements RETURN THE COMPLETED REQUEST FOR RETURN FORM TO YOUR NEAREST LOCATION EUROPE NORTH AMERICA PACIFIC RIM Fax 00 39 011 9979 330 Fax Free 00 800 345 345 00 Fax 1 781 860 9252 please visit our website for individual Toll Free 00 800 234 234 00 Toll Free 800 882 7426 Option 3 office information vpt customercare agilent com vpl ra agilent com http www agilent com Pg 1 3 d Agilent Technologies Vacuum Products Division Request for Return Form Health and Safety Certification Please read important policy information on Page 3 that applies to all returns 1 CUSTOMER INFORMATION Company Name Contact Name Tel Email Fax Customer Ship To Customer Bill To Europe only VAT reg Number USA Canada only Taxable L Non
43. u ll see the led Orange for 1 sec and turned off for two other seconds Electronic Self Test When you switch the pump on with the main On Off switch the pump doesn t start immediately but it starts only after about two seconds This test time isn t required if the pump is already powered as when itis operated in remote or serial mode Rotor Lock Test The rotational frequency is checked continuously If the rotor remains still for more than 20 sec the pump status is changed to Fail 70 78 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Accessories Tab 10 PART NUMBER DESCRIPTION DS42 Inverter Rotary Vane Pumps 87 900 140 01 A 71 18 3 Technical Information Accessories 72 18 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A XE Agilent Technologies Vacuum Products Division Dear Customer Thank you for purchasing an Agilent vacuum product At Agilent Vacuum Products Division we make every effort to ensure that you will be satisfied with the product and or service you have purchased As part of our Continuous Improvement effort we ask that you report to us any problem you may have had with the purchase or operation of our products On the back side you find a Corrective Action request form that you may fill out in the first part and return to us This form is intended to supplement normal lines of communications and to resolve problems that existing systems are
44. um de prudence et dans le respect des normes de pr vention des accidents du travail en vigueur AVERTISSEMENT Lorsque la machine est sous tension faire attention a la pr sence d organes en mouvement et de haute tension AVERTISSEMENT En cas de n cessit de proc der a des op rations de maintenance de la pompe au terme d une p riode de fonctionnement il est indispensable de la laisser refroidir car sa temp rature ext rieure peut tre sup rieure 60 C AVERTISSEMENT Avant toute op ration de maintenance il est imp ratif de toujours couper l alimentation de la pompe Placer les panneaux sp cifiques d avertissement APPAREIL EN COURS DE MAINTENANCE NE PAS BRANCHER L ALIMENTATION pr s de l interrupteur d alimentation Au terme des op rations de maintenance restaurer les dispositifs de s curit CECE DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Mode d emploi 1 ATHENA ANR Ne pas effectuer la substitution d huile imm diatement apr s l arr t de la machine car la temp rature de celle l peut tre lev e Avant de retourner une pompe au constructeur pour r paration il est indispensable de remplir et d adresser au bureau local de vente la fiche Health and Safety Certification jointe la pr sente notice Une copie de celle ci devra tre mise dans l emballage de la pompe avant exp dition En cas de mise au rebut de la pompe proc der son limination con
45. ument that conflict with these terms the warranty terms in the separate agreement shall control Technology Licenses The hardware and or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license Restricted Rights Legend If software is for use in the performance of a U S Government prime contract or subcontract Software is delivered and licensed as Commercial computer software as defined in DFAR 252 227 7014 June 1995 or as a commercial item as defined in FAR 2 101 a or as Restricted computer software as defined in FAR 52 227 19 June 1987 or any equivalent agency regulation or contract clause Use duplication or disclosure of Software is subject to Agilent Technologies standard commercial license terms and non DOD Departments and Agencies of the U S Government will receive no greater than Restricted Rights as defined in FAR 52 227 19 c 1 2 June 1987 U S Government users will receive no greater than Limited Rights as defined in FAR 52 227 14 June 1987 or DFAR 252 227 7015 b 2 November 1995 as applicable in any technical data Trademarks Windows and MS Windows are U S registered trademarks of Microsoft Corporation Safety Notices A CAUTION notice denotes a hazard It calls attention to an operating procedure practice or the like that if not correctly performed or adhered to could re
46. y harm to operators Before connecting the IEC320 mains cable install the Retention Spring provided with the MS40 The Retention Spring has to be fastened to IEC320 connector lateral screws Use the Retention Spring to secure the mains cable into the IEC320 socket Operating procedures technical information and precautions which if not respected and or implemented correctly may cause damage to the pump 52 18 DS42 Inverter Rotary Vane Pumps 87 900 140 01 A Technical Information 3 Warning Notes a Death may result from contact with high voltages Always take extreme care and observe the accident prevention regulations in force b Always disconnect the power supply to the pump before maintenance work Place a special warning signs over the power supply breaker switch MACHINE UNDERGOING MAINTENANCE DO NOT POWER ON c If you are performing maintenance after the pump has been operating for a considerable time allow sufficient time for it to cool as the external surface temperature may in excess of 60 C d Failure to provide the pump with an earth connection may cause serious damage to operators Always ensure that there is an earth connection and that it complies with the standards e When cleaning the pump and its component parts avoid the use of flammable or toxic solvents such as benzin benzol ether or alcohol The recommendation is to use a soap and water solution preferably in ultrasound wash
Download Pdf Manuals
Related Search