製品マニュアル - Providence
Contents
1. D C G HEAT BLASTER LED ON OFF 7V LED DRIVE TONE2. AC PROVIDENCE PAP 5098DCJ LED 230 0051 3 21 7 o S m TEL 045 510 4060 FAX 045 510 4061 URL http www providence jp E mail info1 pacifix Itd com PPD1101 01 Rev 1 0 Povidence HEAT BLASTER HBL 3 OWNER S MANUAL Thank you for choosing Providence In order to take full advantage of the product s features and performance please read this manual thoroughly and keep it in a safe place for future reference HEAT BLASTER Features The Providence HEAT BLASTER HBL 3 pedal is designed to deliver a modern distortion sound that is rich in harmonics and has a fast attack high gain tube di
3. LEVEL BASS BOOST BASS BOOST LED LED 7V LED OIN OUT ON OFF DC9V AC PAP 508DCJ HEAT BLASTER LEVEL TONE DRIVE BAS
4. Povidence HEAT BLASTER HBL 3 PROVIDENCE mS R PROVIDENCE HEAT BLASTER True BypasSS HEAT BLASTER 1 5
5. S BUDOST 1 DC9V AC 9V 1 AC DC9V 8mA 115 D x 72 W x 50 H mm G50g BASS BOOST eo Provide Ence xq z D gt 9 8 g zZ 4 9gV 006P
6. e depth Rotate clockwise for deeper overdrive if TONE Adjusts tone Rotate counterclockwise to cut the high frequencies or clockwise to boost the high frequencies eveL LEVEL Adjusts the output level when the effect is on Rotate clockwise to increase the 9 output level when the effect is on BASS BOOST Switch Boosts the low frequencies Press the switch in to engage the BASS BOOST function LED Indicator Lights blue when the effect is ON The LED will begin to go out if the bat tery voltage drops to less than about 7V INPUT Jack INPUT Jack This is the input to the HBL 3 The output from a guitar or other source device electronic musical instrument or effect unit should be connected here OUTPUT Jack This is the output from the HBL 3 The OUTPUT jack should be con nected to an amplifier or a subsequent effect device ON OFF Footswitch This footswitch turns the effect ON or OFF DC9V INPUT The DC output cable from the regulated 9V AC adaptor connects here TONE BASS BOOST D ovidence z le N 1L M600 HEAT BLASTER Main Specification Controls LEVEL TONE DRIVE BASS BOOST Connectors 1 4 inch phone jack x 2 INPUT and OUTPUT DC 9V input jack AC adaptor jack Power Supply 9V battery or AC adaptor Power Consumption DC 9V 8 mA approx Dimensions 115 D x 72 H x 50 H mm Weight 250 g approx No
7. stortion in a compact pedal This is a sound that wont get buried in any band What s more the HEAT BLASTER does not produce the excessive compression that can be a problem with many distortion pedals for exceptionally natural response The Heat Blaster is ideal for use with the clean channel of a multi channel amplifier In a normal True Bypass circuit in bypass mode the audio signal passes through two switch contacts But in the HEAT BLASTER in bypass mode the audio passes through a single contact thanks to a single contact true bypass circuit The result is much higher sound quality and reliability than that provided by previously existing products Due to the adoption of the new double contact grounding circuit D C G Circuit by inserting a monaural plug into the output jack the shield sleeve of the plug provides two points of contact to the pedal s ground circuit By increasing the area of the point of contact it becomes more difficult for a loose connection to occur and provides the additional advantage of improved sound quality In addition to indicating the pedal s on off status the HEAT BLASTER LED provides effective visual battery power monitoring When the battery voltage drops below 7 volts the LED will become dimmer and begin to go out The effect will still operate at this voltage but to ensure optimum performance the battery should be replaced as soon as possible Controls amp Functions DRIVE Adjusts the overdriv
8. t including battery Battery Replacement To replace the battery remove the bottom panel by unscrewing the four screws that hold it in place Use a 9 volt 006P type battery Be care ful not to apply excessive force to the wiring when changing the battery to avoid broken connections and other damage Precautions e Inserting or removing a plug from the input jack while the unit s output is connected to an amplifier soeakers can cause noise that can dam age the speakers e If the unit malfunctions or behaves abnormally cease operation immediately and refer the problem to the supplier e If the unit will not be used for an extended period of time remove the battery to prevent damage due to chemical leakage from the battery e Use only an AC adaptor with internal voltage regulation e When the battery voltage drops too low for proper operation the effect sound may become weak the output level may drop or no output will be produced at all Be sure to replace the battery as soon as possible if such symptoms occur HiTroubleshooting If the indicator LED does not light Replace the battery with a new one or PA CIFIX L TD H SOUND PRODUCT amp SYSTEM DESIGN connect an appropriate AC adaptor 3 21 7 Tsurumi Chuo Tsurumi ku Yokohama shi JAPAN 230 0051 Specifications and appearance are subject to change without notice TEL 81 45 510 4060 FAX 81 45 510 4061 E mail overseas1 pacifix Itd com URL www providence Itd com PPD1102 01 Rev 1 0
Download Pdf Manuals
Related Search