Ignition Pulse Detector IP-292/296
Contents
1. E Te a O R o a Oo LA z o 59 a E oo O mm Be Ln DOS m A ma gt Or a H e lt lt x S oft lb e E g y a R z cool a L cq R a lt lt E eS m E gt 6 S o fam 2 Hoof E a CO oO o o A dl Gass o o a a EJ o lt x Zs oO a E A N O a 2 ooo CI N oog 2 oO a ae Y en fa a 4 N lt 5 N 05 E 9 N a N E D A a O OWS o Z Cyl a an co a Ol EY o S S oo o ol ls AAN z N o t F DE Ola QV Y g a A A E N das 8 Cl a E m oO oO oO EY 0120 388841 lt FAX 0120 0459354 Copyright ONO SOKKI Co Ltd 2002 All rights reserved 4 B00000189 1M 89082504 5 025 MS 1 9H 0 268507 J 0000000001161 o ONO SOKKI 00000000 oa o 0 oa oa a ooo D2. 2000000 DO0d0o000000 000 e mo
3. Ignition Pulse Detectors IP 292 For primary low voltage IP 296 For secondary high voltage Operating Manual 1 Introduction These detectors are used to detect the number of ignition pulses pro duced in the gasoline engines in the way that the model IP 292 pinches a primary cord low voltage and model IP 296 pinches a secondary cord high voltage of the ignition coil The compact light weight and clip on design of these detectors offer a simple and easy detection of the number of pulse Since the detector and its cord are made of heat resistance mate rials these models are not affected by the high temperature in the engine room Specifications Applicable engine 2 cycle and 4 cycle gasoline engines Point of installation P 292 Primary cord of ignition coil IP 296 Secondary cord high voltage Maximum diameter of coed 10 mm at max Operating temperature 40 C 120 C Storage temperature 50 C 120 C Mass with cable About 280 g Signal cable About 4 9 meters long with C02 BNC type connector Dimensions See Outline Drawing Operation 1 Pull part backward with your thumb and the upper jaw will open Bring cord into the mouth of the detector and release part D and the upper jaw will come down to close the mouth incompletely set IP 292 to the primary cord and IP 296 to the secondary cord of the igni tion coil Push slide knob forward to complete
4. with dust moisture oil or any other foreign matters Keep it always clean in order to obtain the accurate result of measure ment 5 When the detector is not in use place it on a vibration free bench or the like Mechanical vibration mar affect the firm engagement of the upper and lower jaws in the long run causing errors in measurement 6 The detector jaws are made of brittle material Do not give an intensive shock to them because cracked or damaged jaws may fail to detect the pulse 7 Each Ignition Pulse Detector has a label mentioning IP 292 PRI MARY or IP 296 SECONDARY Make sure before measurement that your detector is installed in the correct position as stated 8 In our product following model AR 721 EP 603 AM 161 AT 631 CT 550 CT 650 specify the IP 295 to be used If the IP 296 is used to be combined with such models care should be taken to install the IP 296 reversely in the direction shown in the instruction label 9 Take extremely care of high temperature parts or rotating parts of en gines 5 Outline drawing mm Heat resistant signal cable 4 9m CES y A a y 48 E Omission of Test Qualification Issuance 1 This product is covered by a warranty for a period of one year from the date of Since this product has been tested through a series of strict inspections and a purchase complete program of quality control issuance of the test qualificat
5. O a So o a o o So o oF 005 2 o o oo 22 9 ao ao 2235292 Oo oo Boe Sara oO oo oa Fo a nia aoa Boa ao ao a See Ss Dgo 2905 25 a ofoo 525 52 o pooo a 9 a pasa BAR 303 D2 9 99500 a Bo o pofon 5052 90 5 gogoo0 DODOS ooo oo Mo O oo o 500 00 Boo oa 1 oooooooogooonoooooooooooooooooooooooorioao0 o0000000 D D D
6. ion has 2 This warranty covers free of charge repair for defects judged to be the responsibility been omitted of the manufacturer i e defects occurred while the product is used under normal operating conditions according to descriptions in this manual and notices on the unit label ONO SOKKI 3 For free of charge repair contact either your sales representative or our sales Outer appearance and specifications are subject to change without prior notice office nearby HOME PAGE http www onosokki co jp English english htm 4 The following failures will be handled on a fee basis even during the warranty o oes a ee eS period WORLDWIDE a Failures occurring through misuse operation mistake or modification Ono Sokki Co Ltd b Failures occurring through mishandling dropping or transportation 1 16 1 Hakusan Midori ku c Failures occurring through natural calamities fires earthquakes flooding and Yokohama 226 8507 Japan lightening environmental disruption or abnormal voltage Phone 045 935 3976 For repairs after the warranty period expired contact your sales representative or our Fax 045 930 1906 sales office nearby E mail overseas onosokki co jp
7. ly close the upper jaw The detector jaws must be completely closed during the measure ment 2 Connect the signal cable trailing by the detector to a measuring instru ment Pull raised part in the direction of an arrow to open the upper jaw The diameter of the ignition coil cord must be 10mm or less Remove dust moisture oil and other foreign matters from the mating surface of jaws Warranty To distributer Ensure the 4 Caution in operating 1 Install the detector on the ignition coil in the direction shown in the instruction label on the detector But depending upon the engine type there is a possibility to cause unstable measurements or inaccurate de tection In such case install the detector in the reverse detection Make sure that the detector jaws are completely closed 2 The IP 292 is installed around the primary cord of ignition coil and IP 296 the secondary cord of ignition coil Be careful that so as not to cramp the electrical cable which makes impossible for rpm measure ment Model IP 292 Model IP 296 For primary cord low voltage For secondary cord high voltage Ensure the setting direction a etting direction To battery Plug 3 Although the signal cable is made of the heat resistant materials pass it to the measuring instrument through a low temperature and low noise space in the engine room 4 Take care not to contaminate the mating surface of the jaws
Download Pdf Manuals
Related Search