R614FF-E
Contents
1. EP ID ID 2 4GHz 1 R ON LED 1 50cm 2 ON 3 ON LED X LED 42. R614FF E RC R614FF E Futaba 2 4GHz FASST C2 4PK 4PKS X Futaba FASST Futaba S FHSS FHSS ABE A R614FF E 3 7 7 4 V RX FASST C2 SC oo 4 CH4 3 CH3 2 ME BIC DSC
3. 3 7V 7 4V 3 5V 8 4V F FS FIs 4 35 1x 23 2 x 9 0mm lt 7 6g X BEC TEL 0475 32 6981 299 4395 1080 FUTABA CORPORATION 2011 11 1M23N17457 Futaba R614FF E FASST 2 4GHz System _ Built in Antenna 4 Channel Receiver BIA for EP Car Models AAWARNING NEVER use dry batteries for the power supply of the R614FF E as this may cause difficulties with the receiver s operation NEVER use the R614FF E in GP cars Wrap the receiver with something soft such as foam rubber to avoid vibration Do not splash water over the receiver Since the receiver generates a certain amount of heat install the place with good ventilation Thank you for purchasing the R614FF E receiver The R614FF E is designed for us
4. LED R614FF E FASST 4 2 4GHz BID UD X FASST 2 4GHz 1 LED EEPROM ABS OFF 70m A F FASSTC2
5. Chosei gun Chiba ken 299 4395 Japan Phone 81 475 32 6982 Facsimile 81 475 32 6983 FUTABA CORPORATION 2011 11 1
6. and receiver condition LED Red No signal reception LED Green Receiving signals Receiving signals but ID is unmatched LED GreenBlink LED Red and Green turn on alternately Unrecoverable failure EEPROM etc R614FF E Specifications FASST system 4 channel receiver e Receiving on 2 4GHz band If there are many FASST systems turned on around your receiver it might not link to your transmitter In this case even if the receiver s LED stays solid green unfortunately the receiver might have established a link to one of the other transmitters This is very dangerous if you do not notice this situation In order to avoid the problem we strongly recommend you to double check whether your receiver is controlled by your transmitter by giving throttle input etc and then checking servo response AAWARNING After the linking is done please cycle receiver power and check if the receiver to be linked is really under the control by the transmitter to be linked Do not perform the linking procedure with motor s main wire connected or with the engine operating as it may result in serious injury transmitters Futaba T4PK T4PKS Futaba FASST system does not work with current Futaba S FHSS FHSS system LED Link switch ag i LED sw 4 ZEA EASST 4CHANNEL RECEIVER CH output 1 to 4 Battery DSC terminal B C Usage condi
7. Futaba R614FF E 1M23N17457 FASST 2 4GHz ze AA SS E P High Voltage System 4F py RIS BIA R614FF E HIGH SPEED NORMAL FASST 2 4GHz 4 R614FF E FASST C2
8. e with the Futaba FASST C2 system transmitter The FASST system has two 2 operation mode as shown below eNormal mode High Speed mode The Normal mode accepts any type of servos or the peripheral equipment The High Speed mode only accepts the digital servos including BLS series and most peripheral equipment such as the brushless ESCs However there is a transmitter that cannot correspond to high speed mode Please pay special attention to the information contained within this manual and transmitter s manual in order to have a pleasant running experience sBuilt in antenna The R614FF E receiver is designed to be used only for EP Car models The R614FF E is compatible with the FASST C2 system transmitters Note The R614FF E is compatible with the FASST C2 system Link Procedure Each transmitter has an individually assigned unique ID code In order to start operation the receiver must be linked with the ID code of the transmitter with which it is being paired Once the link is made the ID code is stored in the receiver and no further linking is necessary unless the receiver is to be used with another transmitter 1 Place the transmitter and the receiver close to each other within half 0 5 meter 2 Turn on the transmitter and the receiver 3 Push and hold the Link switch on the receiver 4 When the link is complete the LED on the receiver changes to solid green Please refer to the table below for LED status
9. tion on High Speed mode A CAUTION When using the high speed mode use a Futaba digital servo including brushless servo Analog servos cannot be used e The use of analog servos may cause servo trouble Operating Precautions Once the R614FF E detects the FASST normal mode or FASST high speed mode the detected mode is locked as long as the power is ON When need to change the mode please cycle power e System FASST C2 system At Normal High speed mode auto detection Receiving Range 70m 230ft at the best conditions e Power requirement Rated voltage 3 7V 7 4V Usable voltage 3 5 8 4V e F S and Battery F S function It is set according to the transmitter used Battery F S voltage Set it with the transmitter arbitrarily e Size 1 38x0 91x0 35 35 1x23 2x9 0mm e Weight 0 2702 7 69 Compliance Information Statement for U S A This device trade name Futaba Corporation of America model number R614FF E complies with part1S of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation The responsible party of this device compliance is Futaba Service Center 3002 N Apollo Drive Suite 1 Champaign IL 61822 U S A TEL 217 398 8970 or E mail support futaba rc com Support FUTABA CORPORATION 1080 Yabutsuka Chosei mura
Download Pdf Manuals
Related Search
R614FF E