Operation Guide ANA(ST3)VA
Contents
1. JaA Eora ke YS ERATI Er per ae P 1 100 BE 0 IEI 6 60 1 ae 1 100 x 12 1 100 Se R E 2 oo 3 lt A BN 1 100 4 5 era ps Ney eee PED O DUELE cee ee A z2. NN 1 100 1 AEN EN us 253441930 10 0 eee ED SUIERIEC DARE RTE UOT Operation Guide ANA ST3 V A Setting the Time and Date Some water resistant models are equipped with a screw lock crown With such m
3. 1 17 ae 7 or 60 2 1 100 0 k 24 24 60 1 PCE ERO CIEE D 3 0 EM RGT w Be a K ays 4 1 00 1 1 1 100 2 1 100 3 TOT 31 2 4 6 9 1
4. 00 a m Stopwatch 1 100 atch minute topw j second hand hand This hand rotates and indicates the e np second count Stopwatch second during the first 60 ee seconds The stopwatch lets you measure elapsed time up to 59 minutes 59 99 seconds To measure elapsed time First 60 seconds 1 Press to start the stopwatch 2 Press to stop the stopwatch e You can resume the measurement operation by pressing again 3 Check the elapsed time The example below shows an elapsed time of 44 30 seconds Stopwatch 1 100 IN second hand Stopwatch second 30 hand Y e Press to reset the stopwatch This will enter the Timekeeping Mode 44 seconds To measure elapsed time After the first 60 seconds 1 Press to start the stopwatch e During elapsed time measurement the stopwatch 1 100 second hand automatically rotates for the final second of each minute 2 Press to stop the stopwatch e You can resume the measurement operation by pressing again 3 Press the button and the stopwatch 1 100 second hand will move to the 1 100 second count e If the elapsed time operation was stopped during the final second of each minute the stopwatch 1 100 second hand will already be pointing at the 1 100 second count Do not press the button at this time because doing so will restart the elapsed time operation 4 Check the elapsed time The example below shows an elapsed t
5. cae Operation Guide ANA ST3 V A 1 100 59 59 GODS 0 Aft O A 1M gt gt z oer alae 2 1 100 60 S y
6. ime of two minutes 44 30 seconds Stopwatch minute hand 2 minutes Stopwatch 1 100 second hand 30 Stopwatch second hand 44 seconds e Press to reset the stopwatch This will enter the Timekeeping Mode Notes Do not try to perform stopwatch operations while the crown is pulled out either to the first or second click If you try to press a button you might accidentally cause the crown to rotate and change the current time or day setting If the starting positions of the stopwatch second hand and 1 100 second hand become misaligned use the following procedures to adjust the positions of the hands so they point to 12 o clock when the stopwatch is reset To adjust the positions of the stopwatch hands Press to reset the stopwatch and check the alignment of the stopwatch second hand and 1 100 second hand 2 Pull out the crown to the second click 3 Press to move the stopwatch 1 100 second hand 4 If the stopwatch minute hand is aligned correctly proceed to step 5 If the stopwatch minute hand is also misaligned press to move the stopwatch second hand 5 After making the adjustments you want push the crown back in to its normal position Note that pulling the crown out also stops the timekeeping second hand After performing the above procedure you should also adjust the timekeeping setting
7. odels you must unscrew the crown in the direction noted in the illustration to loosen it before you can pull it out Do not pull too forcibly on such crowns Also note that such watches are not water resistant while their crowns are loosened Be sure to screw the crowns back in as far as they will go after making any setting The watch attached with a bezel can measure the elapsed time Align the Y mark on the bezel with the minute hand by turning it so that the time elapsed from the Vv mark can be measured Elapsed time Hour hand Minute hand First click Setting day a ps Second click Setting time 24 hour hand Day Crown Normal position Second hand To set the time 1 Pull the crown out to the second click e At this time the second hand will move to the 12 o clock position and stop there 2 Set the hands by rotating the crown Rotate the crown to move the hands clockwise Move the minute hand four or five minutes past the time you want to set and then back it up to the proper setting e Make sure that you also set the 24 hour hand to the correct hour of the day 3 Push the crown back in to the normal position to restart timekeeping To set the day 1 Pull the crown out to the first click 2 Set the day by rotating the crown towards you 3 Push the crown back in to the normal position Avoid changing the date setting while the current time is between 9 00 p m and 1
Download Pdf Manuals
Related Search