ソフトダウンステー SDS-C301 取扱説明書 PAT
Contents
1. O O O 0 40 O O O2. 1 ACE SHORE ty E _ 1 g E 2 E Ses GE ERII TONNE Bk 2OmmT mg 20mm i 0 100 200 300 400 500 600 700 800 S00 0 5 mm No
3. SDS C301 US US R US L 7 C 7 J AA 03 3864 1 1 9 00 17 30 FAX 03 3863 6875 E mail support sugatsune co jp 2 5 10 7101 0032 SUGATSUNE LAMP ISO 9001 JSAQ384 IS014001 JSAE597 ISOBO0 1
4. IS014001 http www sugatsune co jp 2013 09 PRINTED IN JAPAN 0034 4 LAMP SOFT DOWN STAY SDS C301 INSTALLATION INSTRUCTION eax Please read this instruction sheet carefully for proper installation and operation Incorrect installation and improper use of the product may damage the unit or cause injury This stay is designed for furniture or lightweight door and is equipped with a damping function Sugatsune guarantees the quality of this product as for all its parts It cannot however guarantee the final assembly as a whole This product was manufactured and delivered with our utmost care Should you however find any defect please contact your dealer immediately Sugatsune warrants that this product is free from defect for a period of one 1 year from the date of delivery Sugatsune liability is limited to the replacement of this product by a similar one free of defect In no case does this extend to the replacement of the installation or the cabinet as a whole Please keep these instructions at hand for future use Sugatsune cannot be held liable for any damage or injury caused by improper use or one different than the one this product was designed for A CAUTIONS Any failure to observe the following precautions may result in personal injury or damage to the cabinet Make sure that installation position and specifications ar
5. SDS C301 3 5X4 3 5X E TAE SDS C301 A B JOTE A B Fi A B A B ASA KTS 230 26 19T 118 153 S AB E 90 90
6. LAMP SDS C30 1 1 Ya
7. e followed Unsuitable installation position may damage the mechanism when in case two stays are used together Make sure that the arm of the stay is parallel with the side panel of the cabinet Please avoid forced opening beyond the opening angle and using excessive force while closing the door This product is designed to operate at room temperatures between 0 C to 40 C 32F 104F This product has a spring at the elbow section Please be careful not to get your fingers caught in elbow section while you are handling the unit Performance of hardware will be affected by unique factors in each application Hardware must be tested in intended application to confirm the function It is necessary to periodically check the fixing screws for loosing Tighten the loosed screws as required Do not force the door to close faster It can cause damage to the product or hinge s THE DIMENSION OF THE FLAP a SOFT DOWN STAY must be used taking the size of the flap into BEI E consideration The graph indicates the usable range when us E i ing one SDS stay When using two stays the width of flap can E be twice as large if the height remains unchanged a zg ad Note The graph shown to the left is in case of a general wood K rr m aes en flap of 20mm thick specific gravity approx 0 5 lt oe o mo m am ao S0 0 70 0 O In case of lighter or hea
8. e pin of the mounting plate screw hitting the stopper pin so that the key hole of the fixing plate The main in the hole of the main body the arm of the stay is straight body must be placed at 90 degrees angle Fix the main body with bind screw against the fixing plate provided Flap ort SA Arm fixing plate ane a ee board Side board SUGATSUNE KOGYO CO LTD SUGATSUNE KOGYO UK LTD SUGATSUNE AMERICA INC SUGATSUNE SHANGHAI CO LTD Phone 81 3 3866 2260 Phone 44 118 9272 955 Phone 1 310 329 6373 Phone 86 21 3632 1858 F a x 813 3866 4447 F a x 44 118 9272 871 F a x 1310 329 0819 F a x 86 21 3632 1868 E mail export sugatsune co jp E mail sales sugatsune co uk E mail sales sugatsune com E mail lamp sugatsune com cn Website www sugatsune intl com Website www sugatsune co uk Website www sugatsune com Website www sugatsune com cn ISO9001 Japan Offices and Sugatsune America and ISO14001 Chiba Production division and Logistic center certified
9. vier flap doors that do not fit within FLAP THICKNESS 20mm FLAP WIDTH mm the above specified range please contact your dealer Code No Suitable Screw on mounting plate Suitable Screw on arm fixing plate SDS C301 3 5x4 3 5x2 S dimension PLATE POSITION FOR INSTALLATION Overlay distance Flap edge for concealed hinge esse of concealed hinge Depending on the type of the hinges used the position of the mount n this case where LAMP hinge 230 26 19T is used the distance for A B is measured from the flap edge i ing plate and arm fixing plate should be fixed as indicated below Side board 9 A B When other types of hinges are used please contact Concealed Hinge 230 26 19T 18mm 153mm S Your dealer 1 inch 25 4mm For right side board The installation direction of the mounting plate Type SDS C301N follows the inscrip tion of US For right side fixing the arrow of R on the US side should point upward vertically For left side fixing the arrow of L on the US side should point upward vertically 105 19 5 83 HOW TO INSTALL Install the mounting plate and arm fixing plate with the enclosed wood screws at the ADJUSTMENT designated places Turn the main body 90 degrees With the flap fully opened adjust the Insert the key of the cam of arm tip into and insert th
Download Pdf Manuals
Related Search