IP7-125 ヘッドクリーニングキット取扱説明書
Contents
1. 70 7 18 K 4 2 SII IP7 125 Head Cleaning Kit User s Guide U00112597 700 November 2008 Apply the head cleaning kit to remove the ink or dust left and congealed at the print head s nozzle surface Components delivered with this kit Head cleaning sheet Support sheet lt 6 pieces gt lt 1 piece gt User s Guide lt 1 copy gt Platen protection sheet lt2. 2 gt OK OK 3 OK 4 5 6
3. 9 70 o 2o u 12 8 16 z 16 16 Ser MORTE a RL hoii 73 74
4. 4cc 1cc 4 1 2 3 8 be 7 OR
5. NOTE Confirm that a waste ink bottle is set to the Be aware that the head cleaning sheet and printer and press the OK button Then platen protection sheet are single use confirm that the carriage IS moved products Repeated use may cause the printer s malfunction INK SYSTEM OPT BOTTLE OK Be sure to apply the specified amount of the wiper cleaning liquid An excessive application may stain a platen or grid roller causing a printer s unexpected failure OPEN COVER CLEANING PH ig Align the head cleaning sheet s holes to the Carriage s protrusion 3 After the carriage stops open the front cover and the cap cover and then manually move the carriage to the capping side CLEANING PH BOTTLE OK Protrusion Usage procedure 2 3 8 Insert the platen protection sheet between the platen and head cleaning sheet to the degree that the sheet s end can be gripped Platen protection sheet 9 Grip the platen protection sheet by rotating the pressure control knob 10 insert the support sheet between the platen protection sheet and head cleaning sheet Confirm that the support sheet s end is aligned with the cutter groove while aligning the support sheet s center with the Carriage s center Support sheet s center Corner support sheet Support sheet s end Corner support sheet Cutter groove Support sheet 11 Close the cap cover and front cov
6. 6 pieces gt Usage procedure 1 3 Start the procedure below only when the printer is ready When no media is loaded at the printer load a media and activate the all user s operation 7 Turn off the preheater print heater and afterheater from the printer s operation panel With the heater control menu confirm that the front paper guide platen and rear paper guide were cooled down to 30 degree C or less When their temperature is not 30 degree C or less wait until they cool down 4 Set the media grip force to OPEN by rotating the pressure control knob Then remove the media 5 Manually move the carriage to the platen s center 6 Absorb 1cc wiper cleaning liquid with a dropper contained in a daily maintenance kit and apply it on the head cleaning sheet s cleaning surface white surface so that the liquid penetrates the cleaning surface Repeat this operation four times to apply the liquid evenly on the whole cleaning surface NOTE Dropper Before starting the head cleaning make sure that the platen and paper guides are cool enough Starting the head cleaning with the platen still hot may accelerate the wiper cleaning liquid s volatilization which may affect the sufficient cleaning or stick the head cleaning sheet to the nozzle plate 2 From the operation panel select PH MAIN MENU and then PH CLEANING INK SYSTEM OPT gt PH CLEANING Head cleaning sheet s cleaning surface
7. SII IP7 125 2008 11 6 gt 6 gt 1 3 7 OFF EAM 30 C 30
8. er The front cover stops on the support sheef cushion Front cover Support sheet s cushion 12 Leave the printer for 8 to 16 hours NOTE Do not leave the printer for 16 hours or more or the capping unit may clog or the wiper cleaning liquid may volatilize As a result the cleaning sheet may adhere to the nozzle plate Usage procedure 3 3 13 Perform the cap s daily maintenance 14 Pull out the support sheet 15 By rotating the pressure control knob set the grip to OPEN Then remove the head cleaning sheet and platen protection sheet at the same time NOTE Be sure to remove the head cleaning sheet and platen protection sheet simultaneously or the platen and front paper guide may be smeared As a result the printer s unexpected malfunction may occur 16 Close the cap cover and front cover Then confirm that the carriage automatically returns to the home position 17 Open the front cover and load a media 18 From the operation panel select PH RECOVERY and then NORMAL Perform the print head cleaning operation NOTE For the detail of the print head cleaning refer to the User s Guide U00112722601 Chapter 2 Basic Operation Print head cleaning Seiko I Infotech Inc
Download Pdf Manuals
Related Search