Home

取扱説明書 - 双葉電子工業株式会社

1. TEL 0475 32 6981 299 4395 1080 1M23N23402 FUTABA CORPORATION 2010 6 1 Futaba S BUS Decoder lt 7 Before using your new SBD 1 please read this manual thoroughly and use the system properly and safely S BUS BUS After reading this manual store it in a safe place Thank you for purchasing an SBD 1 S BUS decoder The SBD 1 is a converter for using conventional servos other than S BUS servo with the S BUS system 1 S BUS Serial communication system for Futaba R C system 2 Use the S BUS hub as the extension code used for the S BUS servo Also SBD 1 can be used Applicable receiver S BUS system receiver only INSTRUCTION MANUAL E Usage Precautions AWARNNG Always use in the state in which the SBD 1 is firmly attached to the fuselage of the airplane or helicopter There is the danger of loss of control and crashing if the connector is disconncted by vibration and shock ACAUTION When using analog servos always use in the state in which the receiver is normal mode There is the danger of erroneous operation or damage on the high speed mode Do not connect any devic
2. S BUS S BUS 1 eiejm 1 S BUS 41 8x12 3x8 4mm 4 ee 5 NO sme do dew SX1 3 SS O S BUS PC Link SX1 SX3 S BUS SBC 1 USB CIU 2 X S BUS R6108SB S BUS X PC Link http www rc futaba co jp hobby SBC 1
3. S BUS gt S BUS LED 4 SBC 1 5 1 X LED lt 5 LED 6 4 5 OZH S BUS S BUS S BUS spus DECODER 2 SBD Pi Io at BEE Futaba soe CPE
4. AZS O SAHO Set
5. 1 S BUS S BUS SBC 1 S BUS 2 SBC 1 LED 1 3 SBC 1 SBD 1 LED SBC 1 SBD 1 LED 1 1 SX1 1 2 SX2 1 3 SX3 Oiz 1 S BUS S BUS S BUS S BUS 2 S BUS S BUS X S BUS
6. Futaba S BUS lt 7 S BUS Q 72572 eens see REMI REN SBD 1 S BUS SBD 1 S BUS SBD 1 SBD 1 S BUS S BUS 2 EOOBRE CT 1 S BUS MESS LEWHO R C 2 S BUS S BUS 3 SBD 1 S BUS
7. ct the servo connection port at which the channel is to be set Each time the switch is pressed the set servo connection port and the number of times the LED blinks change SBC 1 Setting switch operation LED display When power 1 short blink Connector SX1 turned on each second selected Bat al DI 2 short blinks Connector SX2 each second selected quickly SIA cn Pde 3 short blinks Connector SX3 quickly each second selected Channel confirmation When the operation position of the channel selector switch and the channel set at the connector during the SBD 1 servo connector selection coincide the LED changes to a steady light 4 Set the SBC 1 channel selector switch to the channel you want to set 5 Hold down the setting switch about 1 second SBD 1 servo con nector selection Meaning of Special Markings Pay special attention to safety where indicated by the following marks A DANGER Procedures which may lead to a dangerous condition or cause death or serious injury to the user if not carried out AAWARNING properly or procedures where the probability of superficial injury or physical damage is high Procedures where the possibility of serious injury to the user is small but there is a danger of injury or physical damage A CAUTION if not carried out properly S Prohibited Procedures which may lead to dangerous conditions and cause death serious injury if not carried o
8. e gyro battery etc other than servos to the servo connector of the SBD 1 There is the danger of erroneous operation or damage Do not connect an S BUS connector of the SBD 1 to other than an S BUS servo connection port There is the danger of erroneous operation or damage Futaba Corp will not be responsible for damage caused by combination with other than Futaba Genuine parts Name of Each Part and Accessories Upper SBD ff FEE SX1 Middle sx Lower Servo connector S BUS connector lt Accessories gt Channel No Label e Put the channel No label on the servo connector for the identification of channel No Instruction manual this manual EEE channe setting Before installing the SBD 1 to the fuselage set BUS decoder channel setting is impossible with each channel at each servo connector SX1 3 the S BUS receiver R6108SB Use the SBC 1 S BUS channel changer or CIU 2 PC Link software can be downloaded from the USB adapter PC Link software for setting to set home page of your region s Futaba importer the channel eChannel setting by SBC 1 1 Connect the S BUS connector of the SBD 1 to the S BUS servo connection port of the SBC 1 2 Connect the battery to the battery connection port of the SBC 1 Status display LED blinks slowly About 1 sec time 3 Quickly press and release the SBC 1 setting switch and sele
9. ile 81 475 32 6983 1080 Yabutsuka Chosei mura Chosei gun Chiba 299 4395 Japan 1M23N23402 FUTABA CORPORATION 2010 6 1
10. ut properly During channel setting the LED blinks quickly about 5 times sec When the LED changes to a steady light channel setting is complete 6 To set the channel of other servo connection ports quickly press and release the setting switch and repeat steps 4 and 5 BRU age Method Connection 1 Connect the S BUS connector of the SBD 1 to the receiver S BUS connection port or S BUS hub 2 Connect a conventional servo or an S BUS servo to the servo connector of the SBD 1 When an S BUS servo was connected that servo will operate as a conventional servo However it operates on the channel set at the servo connector of the SBD 1 instead of the channel set at the servo itself to the receiver S BUS con nection port or S BUS hub Conventional servo or S BUS servo SBD 1 Ratings e Dimensions 41 8x12 3x8 4mm 1 65x0 48x0 33in excluding protruding e Power requirement Ni Cd Ni MH 4 to 5 cells equivalent battery Futaba Operating temperature range 10 to 45 Mandatory Copyright 2010 No part of this manual may be reproduced in any form without prior permission The contents of this manual are subject to change without prior notice While this manual has been carefully written there may be inadvertent errors or omissions Please contact our service center if you feel that any corrections or clarifications should be made FUTABA CORPORATION Phone 81 475 32 6982 Facsim

取扱説明書 - 双葉電子工業株式会社

Contents

Download Pdf Manuals

Related Search

Related Contents