Home
Multimedia Interface Bedienungsanleitung Instruction
Contents
1. 1 pc multimedia interface 4 pc shunt connector red 4 pc male bullet connector 4 pc female bullet connector Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 General safety instructions WARNINGS Installation requires special knowledge Do not install the unit yourself For safe and reliable installation consult a dealer having special knowledge Installation may only be done during idle status Disconnect the battery from the car s electrical system for example Thereby please pay attention to the car s manufacturer requirements e Never use bolts or nuts from the car s safety devices for installation If bolts or nuts from the steering wheel brakes or other safety devices are used for installation of the unit it may cause an accident Use the unit with a DC 12V negative ground car This unit cannot be used in large trucks which use a DC 24V battery If it is used with a DC 24V battery it may cause a fire or accident Avoid installing the unit in following places Where it would hinder your safe driving Where it could damage the car s fittings CAUTION Since there may be legal regulations defining the permissible installation locations for this unit be sure to install it in a location complying with any such laws The references in this chapter apply to most of our products but not to all If you have further questions please contact your local dealer Do not hit th
2. orange cable is described on page 3 VW MFD2 RNS2 SKODA Nexus Die Installation findet hinter der Navigationseinheit statt Dazu muss diese Ausgebaut und vom Bordnetz getrennt werden Belegung des MOST Steckers an der Navigation Lh a orange lila CAN high pin 9 orange braun CAN low pin 10 braun Masse pin 12 rot gelb Dauerplus pin 15 10 r m Wird der Kabelsatz 1282 verwendet wird dieser zwischen die MOST Buchse des Fahrzeugs und den MOST Stecker der Navigationseinheit installiert Ein abgreifen der oben beschriebenen Leitungen ist nicht n tig Die Belegung der losen violetten und orangenen Leitung finden Sie auf Seite 5 ACHTUNG Bei VW Touareg bitte den Hinweis auf Seite 6 beachten U Sy 94 134 GB Installation has to be done behind the navigation unit II l Therefore the unit has to be pulled out and disconnected from the cars electrical system II tl i Assignment of the MOST connector at the navigation unit al ol azl acl ru orange purple CAN high pin 9 orange brown CAN low pin 10 brown ground pin 12 red yellow permanent 12V pin 15 If cable kit 1282 is used it is installed between the vehicle MOST plug and the navigation unit s MOST connector Cutting the wires is not necessary The wiring of the loose purple and orange cable is described on page 11 ATTENTION With VW Touareg please pay attention to the remarks on page 12 Copyright by Audiotechnik Dietz Ver
3. Bezeichnung Kabel 1 Eingang Dauerspannung 12 V KL 30 rot 2 Ausgang Steuerleitung 5V orange 3 Eingang CAN low blau 4 Eingang CAN high gelb 5 Eingang Masse schwarz 6 Eingang Schalter violett 8 Ausgang CAN high gelb Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 Funktion Das Interface 1280 wird an Dauerplus KI 30 und Masse KI 31 angeschlossen Aufgrund der Bauart muss das Interface in die CAN Datenbusleitungen geschaltet werden Dazu werden diese durchtrennt und mit den Pins 3 4 und 7 8 am Interface verbunden Zur Montage k nnen die beiliegenden Rundhulsen verwendet werden ACHTUNG Niemals CAN high und low gleichzeitig durchschneiden Jede Leitung einzeln Das Interface vor der Montage vom Kabelsatz trennen und erst nach Anschliessen aller Kabel wieder anstecken Zum aktivieren der Funktion w hrend der Fahrt nur R ckw rts muss die violette Leitung des 1280 mit dem R ckfahrscheinwerfer verbunden werden Liegt hier eine Schaltspannung von 12V an so ist das Interface aktiv und erm glicht das z B von einer R ckfahrkamera gelieferte Bild auf dem Navigationsmonitor zu sehen Um das Umschalten zu automatisieren liefert das Interface bei eingelegtem R ckw rtsgang ber die orange Leitung ein Schaltsignal von 5V I max 30mA Dieses kann als Steuersignal verwendet werden MY CAN high AN m CAN low 12V 4 6 Schalter Masse 5 2 Remote 5V Navigation HINWEIS
4. EE E N EE AS 8 COS OF I CY e E E E E E E E EE 8 General safety WAS WUC ONS ee ee en a nnie realen eisen leitete 9 References of legal regulations for operation igri ccccccccseecccceeseecceececceeeeccsssseusiingg seesseseeeeeeueeeeseceeessaageees 10 Installation 1280 a E aaaeeeaa 11 The interface can be used in the following Cars eusseenssnensnnensn ibe cccccescecccsecccceucenecsdeetuesgecssseeecesuseeessegeeessaaes 11 Connector assignment nunseonsnseesannnnennnnnnnnnnnnnnnnnnnnnennnnnnn EEE 222242240000 o nnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 11 Operation a D ccc 2nnunannnnnnannnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnn 12 Service NOteS uuuu02000uunannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnn EEE 4 4nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnn 13 Technical data 00u0020020 22000 nenennnannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn anne EEE scccessceesesecessseeesseeesseeeenesereneeeess 13 Teil eee errr in ener enn srry 14 General advice Dear client many thanks for having chosen an Audiotechnik Dietz product You have made a magnificent choice While developing this product your personal safety combined with the best operating service modern design and an up to date production technique was especially taken into account Unfortunately despite the utmost care injuries and or damages might occur due to improper installation and or use Please read the attached instructi
5. die Garantie Die Baugruppe 1280 ist ein Interface das aus dem Innenraum CAN Protokoll eines Fahrzeugs nachstehend beschriebene Daten verarbeitet Durch den Einbau dieses Artikels in ein Fahrzeug greift man in ein komplexes Gesamtsystem ein das wir als Hersteller und Lieferant der 0 9 Baugruppe nur bedingt kennen k nnen da Unstetigkeiten des Serienstandes innerhalb einer Modellreihe und eines Modelljahres eine bertragbarkeit der hier beschriebenen Kombinationen nicht in jedem Fall zulassen weshalb eine Haftung ausgeschlossen ist Bitte beachten Sie daher generell beim Einbau von elektronischen Baugruppen in Fahrzeugen die Einbaurichtlinien und Garantiebestimmungen des Fahrzeugherstellers damit die Fahrzeuggarantie nicht erlischt Das Interface kann in folgenden Fahrzeugen eingesetzt werden AUDI A3 A4 mit 16 9 DVD Navigation Plus RNS E BMW 3er E90 5er E60 7er E65 und X5 E70 nicht kompatibel f r BMW Rear Seat Entertainment MERCEDES C Klasse W203 und E Klasse W210 mit COMAND 2 0 und original TV Tuner A W169 B W245 C W203 CLK W209 M W164 R W251 mit COMAND APS NTG2 E Klasse W211 mit COMAND APS CLS W219 mit COMAND APS SLK R171 mit COMAND APS SL R230 mit COMAND 2 0 und original TV Tuner bzw COMAND APS DVD PEUGEOT 407 mit Navigations und Telematiksystem RT3 PORSCHE Cayenne mit PCM 2 1 SKODA Octavia II mit Navigation Nexus 16 9 VW mit MFD2 RNS2 Navigation Phaeton Stecker Belegung PIN VO
6. in die ffnungen am Geh use Die Gegenst nde k nnen Kurzschl sse verursachen Achtung Gefahr von Brand oder Elektroschock Sollte das Kabel oder der Anschlu stecker des Ger tes besch digt sein ziehen Sie den Stecker heraus und wenden Sie sich an einen Servicepartner Achtung Gefahr von Brand oder Elektroschock Sorgen Sie daf r dass das Strom anschlu kabel nicht gequetscht wird Schalten Sie bei Rauch Ger usch und oder Geruchsentwicklung das Ger t sofort ab und trennen Sie es sofort von der Spannungsversorgung Benutzen Sie das Ger t nicht weiter Setzen Sie das Ger t keiner starken Sonnenbestrahlung oder anderen starken Hitzeeinwirkungen aus Montieren Sie das Ger t nie in der N he von oder gar ber Radiatoren Warmluftschl uchen oder anderen W rmequellen Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 D E U T S C H Sorgen Sie fur gen gend Luftzirkulation um Sch den an den Geratekomponenten zu vermeiden Ziehen Sie bitte den Stecker der Stromversorgung wenn a Sie das Ger t l ngere Zeit nicht benutzen b Sie das Ger t reinigen m chten benutzen Sie keine feuchten oder Spr h Reiniger Verwenden Sie nur trockene T cher zur Reinigung c das Ger t trotz berpr fung mit Hilfe der Fehlersuche nicht funktioniert wenden Sie sich in diesem Falle an einen unserer Servicepartner Platzieren Sie das Ger t nie in staubiger Umgebung Staubzusamme
7. trunk behind the retainer for navigation unit and TV tuner It is mounted between two body barriers Tap off for rial BALL and low has to be done at the fibre optic cable connector from the AGW brown red CAN high pin 2 brown CAN low pin 4 ex a MERCEDES SLK R171 Die Installation wird am AGW Audio Gateway im vorderen Beifahrerfu raum vorgenommen dazu muss die abgebildete Bedieneinheit nicht ausgebaut werden Abgriff f r CAN high und low geschieht am Lichtwellenleiter Anschluss Stecker vom AGW braun rot CAN high pin 2 braun CAN low pin 4 GB Installation has to be done at the AGW Audio Gateway in the front co driver footwell the control unit showed above has not to be removed for assembly Tap off for CAN high and low has to be done at the fibre optic cable connector from the AGW brown red CAN high pin 2 brown CAN low pin 4 Fundort Location AGW Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 18 MERCEDES SL R230 mit Comand APS Die Installation wird am AGW Audio Gateway hinter dem Fahrersitz vorgenommen dazu muss die abgebildete Bedieneinheit nicht ausgebaut werden Abgriff f r CAN high und low geschieht am Lichtwellenleiter Anschluss Stecker vom AGW braun rot CAN high pin 2 braun CAN low pin 4 GB Installation has to be done at the AGW Audio Gateway behind the driver seat the control unit showed above ha
8. Bei manchen Fahrzeugen z B VW Touareg sind die Anschlusse fur den CAN Bus an der Navigation jeweils doppelt belegt Hier m ssen beide Kabel einer Doppelbelegung abgetrennt und mit dem jeweiligen Eingang f r CAN high und CAN low am 1280 verbunden werden Um Fehler beim Einbau zu vermeiden empfehlen wir den Kabelsatz 1282 zu verwenden Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 Wartungshinweise Das Gerat bedarf keiner Wartung Zum Reinigen des Ger tes benutzen Sie bitte nur ein trockenes Tuch zum Abwischen Gegebenenfalls k nnen Sie bei st rkerer Verschmutzung das Ger t vorsichtig mit einem leicht angefeuchteten Tuch reinigen Benutzen Sie keinesfalls scharfe Reinigungsmittel zum S ubern des Ger tes Technische Daten Software SW 3 2 1 Spannungsversorgung 12 V DC Spannungs Arbeitsbereich 10 0 14 6 V DC Ruhestrom lt 7 MA Leistungsaufnahme max 0 58 W Temperaturbereich 40 bis 85 C Gewicht 0 107 kg Abmessungen 70 x 50 x 30 mm Das Ger t ist f r den automotiven Bereich gedacht und hat daher eine Lebensdauer von maximal 10 Jahren Audiotechnik Dietz Vertriebs GmbH Benzstr 12 D 67269 Gr nstadt Germany info dietz biz www dietz biz Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 Table of content pE e Sae EEan E E ect en ea rt te en aan dss een er re E A EA A A E 8 Ee a AN tess rt ante A O A ane Bisa E E N E A
9. Multimedia Interface Bedienungsanleitung Instruction manual Audiotechnik Dietz Vertriebs GmbH e Benzstr 12 e 67269 Gr nstadt e info dietz biz e www dietz biz Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 Inhaltsverzeichnis ANaAILSVErZEeIEHN S tc wets tse baum eae ce nia sty Anne randval cid bd aed ok E een ne ee 2 PNG CTA CUIAG TAY CUS ass ae bare ade suet yaa een eu ee ee en 2 HVT FOU O ee ee ues sane soa E E E E A tags ounces 2 Allgemeine Sicherheitshinweise u a seen aan 3 Hinweise auf Voraussetzungen f r den Bestimmungsm igen Betrieb 2uu004242000nennnn nennen nnennne nenne 4 Installation 1280 IIe eee cece eseceseseceseeeccghe sprigs lis cccscscsceseseeesseeesesesenees 5 Das Interface kann in folgenden Fahrzeugen eingesetzt werden 2424400 420000BBnnnnnennennnn nennen nnennnn nennen 5 Funktion 000000020000000 00 enanananannnnnnnnnnnnnnnnnnnnn anne N E 6 Wartungshinweise uuuu000s000n0nonononnnannnnnnnnnnnnnnnnnnnnnnnnnnn nenn EEE occcescseeessseessseeeseseceneseeesanseteneesenssesenees T Technische Daten un en cn M o ae naaar anneanne bit T Einbauanleitung ee er Tree iind 14 Allgemeine Hinweise Sehr verehrter Kunde vielen Dank dass Sie sich fur ein Produkt der Firma Audiotechnik Dietz entschieden haben Sie haben eine hervorragende Wahl getroffen Bei der Entwicklung des Produktes wu
10. ar or over a radiator or under the sun This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided Unplug the power cable if a the unit is unused for a long time b you want to clean the unit Do not use liquid cleaners or aerosol cleaners Use a dry cloth for cleaning c the unit doesn t work even after you have consulted the troubleshooting chapter in this case please contact a service partner Do not place this unit on extension dust If the temperature is highly damp agglomerate dust will damage the unit Do not block Slots and openings in the cabinet or in the back or bottom The openings should never be blocked by placing the product on a bed sofa rug or other similar surfaces This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided Do not place this product on an unstable cart stand table etc The product may fall Causing serious injury and serious damage to the product Repairs should only be made by our service partners Never do a repair self otherwise the claim of guarantee expires Unplug the unit from the power source if you have to replace a burned fuse Only use fuses of the same kind and size Wrong fuses can damage the unit References of legal regulations for operation Only use this unit in the intended domain If you use it in a foreign domain if th
11. e activates the interface and makes it possible to view the picture of a for rear view camera on the navigation screen while moving For an automation of switching the interface delivers a signal of 5V I max 30mA at the orange wire as long as the reverse gear is laid in This signal can be used as a remote signal CAN high US 5 CANI 78 12V q 6 Switch ground 5 2 Remote 5V Co ATTENTION In some cars e g VW Touareg the connections for CAN Bus are double clogged at the navigation unit In this case both cables have to be cut and connected with the particular input for CAN high and CAN low at the 1280 To avoid any mistakes while installing we recommend cable kit 1282 Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 13 Service notes This unit does not need any servicing Do not open the housing There are no user serviceable parts inside Wipe gently with a dry cloth over the surface to clean the unit If there is more tough dirt first use a light wet cloth and then use a dry one Never use corrosive cleaners to clean the unit Technical data Software SW 3 2 1 Power supply 12 V DC Working Voltage 10 0 14 6 V DC Quiescent current lt 7 mA Power consumption 0 58 W Temperature range 40 85 C Weight 0 107 kg Dimensions 70 x 50 x 30 mm This unit is only for automotive use and has therefore a lifetime of max 10 years Audiotec
12. e unit is not installed properly or if the unit will be reconstructed the guarantee will expire Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 11 Installation 1280 Attention Absolutely necessary to read The interface 1280 is only for use of the afterwards described combination If the device is installed incorrect warranty will be lost Unit 1280 is an interface which processes afterwards described data from the CAN protocol of a car Its installation in a car means an important interference into a complex system which we as a supplier of the above mentioned unit do not know very well We cannot guarantee that picking off data from the CAN Bus system may not influence other electronic units or systems in the car So if you install electronic units in cars please always pay attention to the installation guides and the warranty regulations of the car producer because otherwise the warranty will be lost Because the changes in mass production of the cars we also cannot guarantee that the interface is suitable in all the above mentioned combinations To avoid risks we advise you to contact the car producer or one of his dealers The interface can be used in the following cars AUDI A3 A4 with 16 9 DVD Navigation Plus RNS E BMW Series 3 E90 Series 5 E60 Series 7 E65 and X5 E70 not compatible for BMW Rear Seat Entertainment MERCEDES C Class W203 and E Class W210 with COMAND 2 0 and orig
13. gation unit yellow CAN low pin 9 black CAN high pin 11 brown ground pin 12 brown red permanent 12V pin 15 If cable kit 1283 is used it is installed between the vehicle MOST plug and the navigation unit s MOST connector ATTENTION Possibly installed fibre optics have to be disconnected from the vehicle MOST plug and reconnected in the cable kit MOST plug Cutting the wires is not necessary The wiring of the loose purple and orange cable is described on page 11 ATTENTION With an activated interface 1280 it is not possible to navigate simultaneously 06 07 on BMW 7er Series 7 E65 Die Installation findet hinter dem Monitor statt Den Monitor wie unten Abgebildet ausbauen GB Installation has to be done behind the monitor For removal of the monitor see following pictures Zundung ausschalten und den grossen AMP Stecker aus dem Monitor ziehen Belegung des AMP Steckers orange gr n CAN high grun CAN low braun schwarz Masse rot schwarz Dauerplus ACHTUNG Solange das Interface 1280 aktiv ist kann mit der Navigation ab Baujahr 06 07 nicht gleichzeitig navigiert werden GB Turn off the ignition and disconnect the big AMP connector from the monitor Assignment of the AMP connector orange green CAN high green CAN low brown black ground red black permanent 12V ATTENTION With an activated interface 1280 it is not possible to navigate simultaneously 06 07 on Copyright by Audio
14. hnik Dietz Vertriebs GmbH Benzstr 12 D 67269 Grunstadt Germany info dietz biz www dietz biz Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 14 Einbauanleitung Installation AUDI DVD Navigation RNS E A3 A4 Die Installation findet hinter der Navigationseinheit statt Dazu muss diese Ausgebaut und vom Bordnetz getrennt werden Belegung des MOST Steckers an der Navigation orange lila CAN high pin 9 orange braun CAN low pin 10 braun Masse pin 12 rot gelb Dauerplus pin 15 Audi Navigation plus RADIO Ty NAME TEL Wird der Kabelsatz 1282 verwendet wird dieser zwischen die MOST Buchse des Fahrzeugs und den MOST Stecker der Navigationseinheit installiert Ein abgreifen der oben beschriebenen Leitungen ist nicht n tig Die Belegung der losen violetten und orangenen Leitung finden Sie auf Seite 5 ACHTUNG Solange das Interface 1280 aktiv ist kann mit der Navigation RNS E nicht gleichzeitig navigiert werden GB Installation has to be done behind the navigation unit a 2 Therefore the unit has to be pulled out and disconnected II l from the cars electrical system Assignment of the MOST connector at the navigation unit riot i T F al tal LU orange purple CAN high pin 9 orange brown CAN low pin 10 brown ground pin 12 read yellow permanent 12V pin 15 If cable kit 1282 is used it is installed between the vehicle MOST plug and the navigatio
15. ie Fahrsicherheit oder die Funktionstuchtigkeit anderer im Fahrzeug verbauter Unterbaugruppen eingeschrankt wurde HINWEIS Bitte verwenden Sie die in dieser Montageanleitung vorgeschriebenen Anschlusse zur Montage des Gerates Die hier aufgef hrten Hinweise treffen zwar auf die meisten aber nicht auf alle Produkte gleicherma en zu Sollten Sie Fragen hierzu haben wenden Sie sich bitte an Ihren H ndler Lassen Sie das Ger t nicht fallen Vermeiden Sie Besch digungen Ist das Ger t heruntergefallen oder ist das Geh use besch digt wenden Sie sich bitte an einen Servicepartner Achtung Gefahr von Elektroschock ffnen Sie nie das Geh use Es gibt keine zu wartenden Teile im Inneren Lassen Sie Service oder Reparaturarbeiten nur von qualifizierten Personen durchf hren Achtung Gefahr von Brand oder Elektroschock Setzen Sie das Ger t keinem Regen oder anderer Feuchtigkeit Badewanne Schwimm oder Sp lbecken aus Stellen Sie keine wasserbeinhaltenden Objekte wie beispielsweise Trinkgl ser oder Blumenvasen auf dem Ger t ab Achtung Gefahr von Elektroschock Vermeiden Sie bei Gewitter eine Ber hrung mit dem Geh use und ziehen Sie die Stecker der Spannungsversorgung und Antennen vom Ger t ab um Sch den zu vermeiden Achtung Gefahr von Brand oder Elektroschock berlasten Sie auf keinen Fall die Stromanschl sse oder die Verlangerungskabel Achtung Gefahr von Brand oder Elektroschock Stecken Sie niemals Fremdk rper
16. inal TV tuner A W169 B W245 C W203 CLK W209 M W164 R W251 with COMAND APS NTG2 E Class W211 with COMAND APS CLS W219 with COMAND APS SLK R171 with COMAND APS SL R230 with COMAND 2 0 and original TV tuner COMAND APS DVD PEUGEOT 407 with navigation system RT3 PORSCHE Cayenne with PCM 2 1 SKODA Octavia Il with Nexus 16 9 navigation VW with MFD2 RNS2 navigation Phaeton Connector assignment PIN VO marking cable 1 Input Power 12 V KL 30 red 2 output remote 5V orange 3 Input CAN low blue 4 Input CAN high yellow 5 Input ground black 6 Input switch purple 8 output CAN high yellow Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 12 Operation The interface 1280 basically has to be connected with permanent 12V terminal 30 and ground terminal 31 Due to the electronic design the interface has to be connected in serial to the CAN bus wires Therefore the CAN bus has to be cut through and connected with Pin 3 4 and 7 8 to the interface 1280 For assembling the enclosed bullet sleeves can be used ATTENTION Never cut CAN high and low simultaneously Only one single wire Connection of cables should only be done with a disconnected interface For activating the stand by function of the picture while driving only backwards the purple wire from 1280 has to be connected with the signal for back up light A voltage of 12V at the purple wir
17. is product Avoid any damage Warning Risk of electric shock Never remove the cover There are no user serviceable parts inside Refer servicing to qualified personal Warning Risk of fire or electric shock Do not use this product near water for example bathtub washbowl etc or in wet basements Swimming pool To reduce the risc of casualties never expose the unit any moisture Never put a wet object like a flower pot on the unit Warning Risk of electric shock To protect the unit against damage unplug the power cable and the antennas of the unit if a thunder is present Warning Risk of fire or electric shock Do not overload wall outlets and extension cords Warning Risk of fire or electric shock Never insert objects of any kind into this product through openings They can cause short circuits which could result in fire or electric shock Warning Risk of fire or electric shock When the cable or plug of this product is broken please pull out the plug and refer servicing to qualified personal Warning Risk of fire or electric shock Don t put anything on the power cable This can damage the cable If smoking abnormal sound or peculiar smell happens disconnect the power source Stop using this unit Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 10 Protect the unit against any kind of heat Never mount it close to heat sources This product should never be placed ne
18. n units MOST connector Cutting the wires is not necessary The wiring of the loose purple and orange cable is described on page 11 ATTENTION With an activated interface 1280 it is not possible to navigate with RNS E simultaneously BMW 3er E90 5er E60 X5 E70 Series 3 E 90 Series 5 E60 X5 E70 11 5 9 13 Die Installation findet hinter der Navigationseinheit statt Pet ert nicht am Monitor Dazu muss diese Ausgebaut und vom Bordnetz getrennt werden Belegung des MOST Steckers an der Navigation gelb CAN low pin 9 schwarz CAN high pin 11 braun Masse pin 12 braun rot Dauerplus pin 15 Wird der Kabelsatz 1283 verwendet wird dieser zwischen die MOST Buchse des Fahrzeugs und den MOST Stecker der Navigationseinheit installiert ACHTUNG Eventuell vorhandenen Lichtleiter vom Fahrzeug MOST Anschluss in die Anschlussbuchse des Kabelsatzes stecken Ein abgreifen der oben beschriebenen Leitungen ist nicht notig Die Belegung der losen violetten und orangenen Leitung finden Sie auf Seite 5 ACHTUNG Solange das Interface 1280 aktiv ist kann mit der Navigation ab Baujahr 06 07 nicht gleichzeitig navigiert werden Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 15 GB Installation has to be done behind the navigation unit not behind the monitor Therefore the unit has to be pulled out and disconnected from the cars electrical system Assignment of the MOST connector at the navi
19. nballung infolge von Temperatureinwirkung kann das Ger t zerst ren Verstopfen Sie keine ffnungen am Geh use an der R ckseite oder am Boden Stellen Sie das Ger t nie auf ein Bett Sofa oder hnliche Oberfl chen Auch hier k nnen die Offnungen verdeckt werden Stellen Sie das Ger t nie in geschlossen umbaute M bel wenn dadurch die Luftzirkulation gef hrdet wird Stellen Sie das Ger t nicht auf instabile Unterkonstruktionen Durch Herunterfallen des Ger tes k nnten Sie verletzt und das Ger t besch digt werden Lassen Sie Reparaturen immer nur von unseren Servicepartnern durchf hren Bei selbst reparierten Ger ten erlischt der Garantieanspruch Wenn Sie eine durchgeschmolzene Sicherung ersetzen m ssen schalten Sie das Ger t ab und trennen Sie es von der Spannungsversorgung Benutzen Sie nur Sicherungen gleicher St rke als Ersatz um Sch den am Ger t zu vermeiden Hinweise auf Voraussetzungen f r den Bestimmungsm igen Betrieb Setzen Sie das Ger t nur in dem ihm zugedachten Bereich ein Bei zweckfremdem Gebrauch nicht fachgerechter Installation oder bei Umbauten erl schen die Betriebs erlaubnis und der Garantieanspruch Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 Installation 1280 Achtung Unbedingt lesen Das hier beschriebene Interface ist nur f r den Einsatz in den nachstehenden Kombinationen geeignet Bei falschem oder fehlerhaftem Einbau erlischt
20. on manual completely with great care and keep it This product meets the actual European and national directions The conformity was proved the respective documents and explanations are stored with the manufacturer All articles of our production line pass through a 100 check for your safety and security We reserve the right to carry out technical changes which serve the improvement at any time According to each article and purpose it is sometimes necessary to check each country s legal regulations before installing and starting the unit In case of guarantee claims the device has to be sent back to the seller in the original packaging with the attached bill of purchase and detailed defect s description Please pay attention to the manufacturer s return requirements RMA The legal warranty directions are valid The guarantee claim as well as the operating permission becomes invalid due to a unauthorized changes to the device or accessories which have not been approved or carried out by the manufacturer or its partners opening the device s frame device s repairs carried out by one s own improper use operation brute force to the device drop wilful damage accident etc b C d e ees ni nt NSA During installation please pay attention to all safety relevant and legal directions The device has only to be installed by trained personnel or similarly qualified people Scope of delivery 1 pc instruction manual
21. osen violetten und orangenen Leitung finden Sie auf Seite 5 GB Installation has to be done behind the navigation unit Therefore the unit has to be pulled out and disconnected from the cars electrical system Assignment of the MOST connector at the navigation unit brown CAN low pin 9 brown red CAN high pin 11 brown ground pin 12 red blue permanent 12V pin 15 If cable kit 1283 is used it is installed between the vehicle MOST plug and the navigation unit s MOST connector ATTENTION Possibly installed fibre optics have to be disconnected from the vehicle MOST plug and reconnected in the cable kit MOST plug Cutting the wires is not necessary The wiring of the loose purple and orange cable is described on page 11 Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 17 MERCEDES E Klasse E Class W211 CLS W219 Die Installation wird am AGW Audio Gateway im Kofferraum vorgenommen dazu muss die abgebildete Bedieneinheit nicht ausgebaut werden Das AGW befindet sich links hinter dem Halter fur Navi Rechner und TV Tuner zwischen zwei Karosseriewanden Abgriff f r CAN high und low geschieht am Lichtwellenleiter Anschluss Stecker vom AGW braun rot CAN high pin 2 braun CAN low pin 4 GB Installation has to be done at the AGW Audio Gateway in the trunk the control unit showed above has not to be removed for assembly The AGW is located in the left side of the
22. rde besonders auf Ihre pers nliche Sicherheit kombiniert mit bestmoglichstem Bedienungskomfort modernem Design und aktuelle Produktionstechniken geachtet Aber trotz gr tm glicher Sorgfalt kann es bei unsachgemafser Installation oder Benutzung oder bei falscher Bedienung zu Verletzungen oder und Sachsch den kommen Bitte lesen Sie deshalb die Ihnen vorliegende Bedienungsanleitung sorgf ltig und vollst ndig durch und bewahren Sie diese auf Dieses Produkt erf llt die Anforderungen der geltenden europ ischen und nationalen Richtlinien Die Konformit t wurde nachgewiesen die entsprechenden Unterlagen und Erkl rungen sind beim Hersteller hinterlegt Alle Artikel aus unserer Produktion durchlaufen eine 100 ige Pr fung zu Ihrer Sicherheit Wir behalten uns vor jederzeit technische nderungen durchzuf hren die dem Fortschritt dienen Je nach Artikel und Einsatzzweck ist es eventuell notwendig vor der Installation bzw Inbetriebnahme die gesetzlichen Bestimmungen des jeweiligen Landes zu pr fen Das Ger t ist bei Garantieanspr chen in der Originalverpackung mit beigelegtem Kaufbeleg und detaillierter Fehlerbeschreibung dem Verk ufer einzuschicken Beachten sie hierbei die R cksendebestimmungen des Herstellers RMA Es gelten die gesetzlichen Gew hrleistungsvorschriften Der Garantieanspruch und auch die Betriebserlaubnis erlischt durch a unbefugte nderungen am Ger t oder Zubeh r die nicht vom Hersteller oder dessen Pa
23. rtnern durchgef hrt oder genehmigt wurden ffnen des Geh uses eines Ger tes selbst ausgef hrte Reparaturen am Ger t unsachgem e Nutzung nicht bestimmungsgem e Nutzung Betrieb Gewalteinwirkung auf das Ger t Herabfallen mutwillige Zerst rung Unfall etc oO Qa O N ee NI D Beachten Sie beim Einbau alle sicherheitsrelevanten und gesetzm igen Bestimmungen Das Ger t darf nur durch geschultes Fachpersonal oder hnlich qualifizierte Personen eingebaut werden Lieferumfang 1 St Bedienungsanleitung 1 St Multimedia Interface 4 St Abzweigverbinder rot 4 St Rundstecker rot 4 St Rundsteckh lsen rot Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 Allgemeine Sicherheitshinweise WARNUNG Die Installation darf nur durch geschultes Fachpersonal durchgefuhrt werden Installationen nur im spannungslosen Zustand vornehmen Dafur z B die Batterie vom Bordnetz trennen beachten Sie dabei bitte die Vorgaben des Fahrzeugherstellers Verwenden Sie niemals sicherheitsrelevante Schrauben Bolzen oder sonstige Befestigungspunkte an Lenkung Bremssystem oder anderen Komponenten um Ihre eigene Fahrsicherheit nicht zu gef hrden SchlieBen Sie das Gerat nur an 12V KFZ Spannung mit Masseverbindung zur Karosserie an Diese Unterbaugruppe ist nicht zugelassen zum Einsatz in LKWs oder anderen KFZ mit 24V Bordspannung Vermeiden Sie den Einbau des Gerates an Stellen wodurch d
24. s not to be removed for assembly Tap off for CAN high and low has to be done at the fibre optic cable connector from the AGW brown red CAN high pin 2 brown CAN low pin 4 PEUGEOT407 1 gt gt 131 Die Installation findet hinter der Navigationseinheit statt Dazu litt muss diese Ausgebaut und vom Bordnetz getrennt werden II II Belegung des MOST Steckers an der Navigation el aol sel Al 40 88 120 16 wei CAN high pin 10 grau CAN low pin 13 Wird der Kabelsatz 1284 verwendet wird dieser zwischen die MOST Buchse des Fahrzeugs und den MOST Stecker der Navigationseinheit installiert ACHTUNG Eventuell vorhandenen Lichtleiter vom Fahrzeug MOST Anschluss in die Anschlussbuchse des Kabelsatzes stecken Ein abgreifen der oben beschriebenen Leitungen ist nicht n tig Die Belegung der losen violetten und orangenen Leitung finden Sie auf Seite 5 ACHTUNG Solange das Interface 1280 aktiv ist kann mit der Navigation RT3 nicht gleichzeitig navigiert werden Zur Aktivierung des 1280 muss das Fahrzeug stehen GB Installation has to be done behind the navigation unit Therefore the unit has to be pulled out and disconnected from the cars electrical system Assignment of the MOST connector at the navigation unit white CAN high pin 10 grey CAN low pin 13 If cable kit 1284 is used it is installed between the vehicle MOST plug and the navigation units MOST connector ATTENTION Possibly installed fibre optics ha
25. technik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 16 MERCEDES C W203 E W210 SL R230 mit with COMAND 2 0 Die Installation findet hinter der Navigationseinheit statt Dazu muss diese Ausgebaut und vom Bordnetz getrennt werden Der Anschluss erfolgt am C2 Block braun rot CAN high pin 9 braun CAN low pin 8 Wird der Kabelsatz 1286 verwendet beachten Sie bitte den Einbauhinweis der dem Artikel beiliegt GB Installation has to be done behind the navigation unit Therefore the unit has to be pulled out and disconnected from the cars electrical system Connection at C2 as follows brown red CAN high pin 9 B brown CAN low pin 8 If cable kit 1286 is used see the manual of this product MERCEDES A W169 B W245 C W203 CLK W209 M W164 R W251 amp COMAND APS NTG2 Die Installation findet hinter der Navigationseinheit statt Dazu muss diese Ausgebaut und vom Bordnetz getrennt werden Belegung des MOST Steckers an der Navigation braun CAN low pin 9 braun rot CAN high pin 11 braun Masse pin 12 rot blau Dauerplus pin 15 Wird der Kabelsatz 1283 verwendet wird dieser zwischen die MOST Ter ert Buchse des Fahrzeugs und den MOST Stecker der Navigationseinheit II I installiert ACHTUNG Eventuell vorhandenen Lichtleiter vom Fahrzeug iid MOST Anschluss in die Anschlussbuchse des Kabelsatzes stecken Denen EA Ein abgreifen der oben beschriebenen Leitungen ist nicht n tig Die Belegung der l
26. triebs GmbH e Germany Rev 6 Stand 07 2008 20 VW Phaeton Die Installation findet hinter der Navigationseinheit Monitor am gr nem 32 pin Stecker statt dazu muss diese Ausgebaut und vom Bordnetz getrennt werden Kabelfarben Fahrzeugseitig orange gr n CAN high pin 16 orange braun CAN low pin32 braun Masse Strom ISO pin 8 rot Dauerplus Strom ISO pin 7 GB Installation has to be done behind the navigation unit Therefore the unit has to be pulled out and disconnected from the cars electrical system Assignment of the green 32 pin connector orange green CAN high pin 16 orange brown CAN low pin 32 braun ground power ISO pin 8 rot permanent 12V power ISO pin 7 Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008
27. ve to be disconnected from the vehicle MOST plug and reconnected in the cable kit MOST plug Cutting the wires is not necessary The wiring of the loose purple and orange cable is described on page 11 ATTENTION With an activated interface 1280 it is not possible to navigate with RT3 simultaneously For activating 1280 the vehicle mustn t move Copyright by Audiotechnik Dietz Vertriebs GmbH e Germany Rev 6 Stand 07 2008 19 PORSCHE Cayenne PCM 2 1 Die Installation findet hinter der Navigationseinheit statt Dazu muss diese Ausgebaut und vom Bordnetz getrennt werden Der Anschluss erfolgt am mini ISO Block orange lila CAN high orange braun CAN low Wird der Kabelsatz 1285 verwendet wird dieser zwischen die MINI ISO und ISO Buchse des Fahrzeugs und den MINI ISO und ISO Stecker der Navigationseinheit installiert Ein abgreifen der oben beschriebenen Leitungen ist nicht notig Die Belegung der losen violetten und orangenen Leitung finden Sie auf Seite 3 GB Installation has to be done behind the navigation unit Therefore the unit has to be pulled out and disconnected from the cars electrical system Connection at mini ISO as follows orange purple CAN high orange brown CAN low If cable kit 1285 is used it is installed between the MINI ISO and ISO plug of the vehicle and the MINI ISO and ISO connector of the navigation unit Tapping off the wires is not necessary The wiring of the loose purple and
Download Pdf Manuals
Related Search
Related Contents
CT Multisplit 40MSD-D-09 Copyright © All rights reserved.
Failed to retrieve file