Home

the QQ Yak manual

Contents

1. 77 CANOPY INSTALLATION L17 Continue the mold line to the sides of the canopy and cut outside the line by Remove the masking paper and mask the entire canopy with masking tape Make handles by folding a piece of masking tape This helps to move the 1 16 inch Black line shows the mold line Mount the canopy in the canopy frame canopy in the frame for final adjustment 78 CANOPY INSTALLATION L110 L111 112 Use strong earth magnets to hold the canopy to the frame by using one Once the canopy is centered mark the edges using a felt pen Remove the canopy from the frame Using a hobby knife remove the masking magnet from the inside and one from the outside pinching the canopy For tape below the marked line best result use 10 12 pairs of magnets Do not use tape 79 CANOPY INSTALLATION L113 L114 O15 Using the back of the hobby knife scratch the canopy where it meets with the Insert the canopy in the frame one last time for final adjustment and check Once satisfied apply a bead of canopy glue Formula 560 to the canopy frame It is extremely important that canopy sits flush with the frame with no to frame extremely minimum gap 80 CANOPY INSTALLATION L116 L117 L118 Apply some canopy glue Formula 560 to the canopy Insert the canopy in the frame and use magnets to hold in place Clean excess Mask the fusela
2. Pass the pull pull cable through the brass sleeve eye bolt and loop back in Use a crimper and crimp the cable Install the servo in the rudder tray the sleeve 36 RUDDER SERVO AND PULL PULL CABLE INSTALLATION e EINBAU VON H HENRUDERSERVO UND PULL PULL KABEL ASSEMBLAGE DU CABLE PULL PULL ET DU SERVO DE LA GOUVERNE DE DIRECTION e INSTALLAZIONE DEL SERVO DEL TIMONE E DEI CAVETTI DI COMANDO L110 L111 0112 AN Using a crescent wrench and ball driver install the ball link in the rudder Exit the cable through the fuselage opening Cables exit straight Tape the rudder at the center using masking tape and power on the servo control horn by connecting it to the receiver RUDDER SERVO AND PULL PULL CABLE INSTALLATION e EINBAU VON HOHENRUDERSERVO UND PULL PULL KABEL ASSEMBLAGE DU CABLE PULL PULL ET DU SERVO DE LA GOUVERNE DE DIRECTION e INSTALLAZIONE DEL SERVO DEL TIMONE E DEI CAVETTI DI COMANDO L113 014 015 Pull the cable tight and pass through the brass sleeve eye bolt and back to Cut the excess cable Make sure there s no slack in the cable if need be adjust the tension sleeve Pull the cable so there is no slack and crimp the brass fitting 38 ELEVATOR SERVO AND STAB INSTALLATION e 002 LILI3 Prepare the servo by inserting the rubber grommets and eyelets
3. Utilisez du frein filet Applicare fuido thread lock Assemble right and left Links und rechts montie ren Assemblez droite et gauche Assemblare destra e sinistra Repeat multiple times as indicated Vorgang wiederholen wie angezeigt Repetez comme indique Ripetere piu volte come indicato Ensure proper orientation Ausrichtung Richtung sicherstellen V rifiez la bonne orienta tion Assicurars dell appropriato orienta mento Ensure free rotation Rotation sicherstellen Permettez une rotation libre Assicurarsi rotazione libera Push tightly Fest dr cken Serrez fortement Spingere forte Apply Oil l verwenden Appliquez du lubrifiant Applicare olio Attach Temporarily Vor bergehend anbrin gen Attachez temporaire ment Attaccare temporanea mente Use medium CA Mittelfl ssigen Sekun denkleber verwenden Utilisez de la cyanoac rylate moyenne Usare CA media Use thin CA D nnfl ssigen Sekun denkleber verwenden Utilisez de la cyanoac rylate fine Usare CA fine Fully Tighten Vollst ndig festziehen festschrauben Serrez compl tement Stringere al massimo Use hobby knife with 11 blade Verwenden Sie ein Hobbymesser mit 11 Klinge Utilisez un Couteau Lame num ro 11 Usare taglierino
4. 4 40 x 1 2 inch 4 40 x 1 inch ass Silicone py Silikonschlauch Tube silicone Silicone ci 2 56 Plastic 2 56 Kunststoff 2 56 Chape en plastique 2 56 Forcella in plastica A 3 4 40 metal PI 4 40 Metall FT TT 4 40 Chape en m tal 4 40 Forcella in metallo Machined Aluminum Jury strut attachment x4 Aluminium Strebenhalter x4 Chape de fixation de hauban usin e en alu minium 4 Attacco struttura in alluminio x4 i Machined Aluminum Strut End x4 Aluminium Strebenanschluss x4 Embout de liaison de hauban en aluminium usine x4 Finale struttura in alluminio x4 Steel Strut Attachment Pin x8 gt Sicherungspin f Strebe x8 Axe de fixation de hauban X8 Pin di fissaggio struttura in alluminio x8 Aluminum Fuselage Strut i Attachment x2 Aluminium Rumpf Streben halter x2 Ferrure de fixation des hau bans sous le fuselage X2 Attacco fusoliera della strut tura in alluminio x2 Machined Strut Attachment x4 Strebenhalter x4 Ferrure de fixation des haubans X4 97 Attacchi struttura in alluminio x4 ASSEMBLY SYMBOL GUIDE e MONTAGE SYMBOLE e GUIDE DES SYMBOLES POUR ASSEMBLAGE e GUIDA Al SIMBOLI DI ASSEMBLAGGIO e D 47 Apply threadlock Schraubensicherung slack verwenden
5. Pass the female side of the JR Heavy Duty 36 inch extension through the servo lead cut out of the stab Using a rod with a hook at the end grab the servo extension and pull out through the servo opening 39 ELEVATOR SERVO AND STAB INSTALLATION e LILIA LILIS LILI6 Attach the servo lead to the extension and use a string to secure the connec Mount the servo so that the output shaft is closer to leading edge of the stab Use a magnetic tip screw driver or a magnet and insert the screw tor Then pull the extension through the servo lead opening eg 40 ELEVATOR SERVO AND STAB INSTALLATION 007 0108 BIS Using a 1 Philips head screw driver tighten the screws Temporarily power up the servo and mount the arm perpendicular to the Use thread lock on the center servo screw and tighten the screw servo output shaft Use sub trim if necessary 41 ELEVATOR SERVO AND STAB INSTALLATION e 0010 0011 0012 Turn the power off to the servo and move the arm to the sides to install the Prepare the ball links so that the length of the rod is 52mm between ball links Using a crescent wrench and 3 32 inch ball driver install the ball link onto servo arm set screws the outermost hole in the Hangar 9 servo arm 42 ELEVATOR SERVO AND STAB INSTALLATION 0013 0014 0015 Using a crescent wrench and 2 5mm ball
6. VORFLUGKONTROLLE Laden Sie den Gender Empfanger und Z ndakku f r Ihr Flugzeug Verwenden Sie f r die RC Anlage bitte das empfohlene Ladegerat Folgen Sie zum Lad en des Senders den Anweisungen aus der Bedien ungsanleitung Laden Sie den Sender den Abend vor dem Flug Nutzen Sie zum Laden von Sender und Empf ngerakku nur im Lieferumfang befindliche oder empfohlene Ladeger te Folgen Sie allen Herstell eranweisungen der elektrischen Komponenten Pr fen Sie den RC Einbau und stellen sicher dass alle Ruderfunktionen Quer H hen Seitenruder und Gas sich in die richtige Richtung mit den empfohle nen Ausschlagen bewegen berpr fen Sie alle Teile der Anlenkungen Ruder h rner Servohebel und Gabelk pfe und stellen Sicher dass diese gut befestigt und in einwandfreiem Zustand sind Vor jeder Flugsession und insbesondere mit einem neuem Modell f hren Sie einen Reichweitentest mit dem RC System durch Sehen Sie f r die Durchf h rung und Reichweite in der Bedienungsanleitung ihrer Fernsteuerung nach Lassen Sie den Motor laufen Wiederholen Sie mit laufenden Motor den Reichweitencheck Die Reichweite sollte nicht signifikant beeinfluBt werden Ist dieses der Fall fliegen Sie nicht Bauen Sie die RC Komponenten aus und lassen diese vom Hersteller berpr fen CHECKLIST D AVANT VOL Chargez la batterie de votre metteur de r ception et d allumage Utilisez le chargeur fourni avec votre ra dio Suivez les
7. l utilisateur pour une utilisation donn e du produit Il est de la seule responsabilit de l acheteur de v rifier si le produit correspond ses capacit s et l utilisation pr vue c Recours de l acheteur Il est de la seule discr tion d Horizon de d terminer si un produit pr sentant un cas de garantie sera r par ou chang Ce sont l les recours exclusifs de l acheteur lorsqu un d faut est constat Horizon se r serve la possibilit de v rifier tous les l ments utilis s et susceptibles d tre int gr s dans le cas de garantie La d cision de r parer ou de remplacer le produit est du seul ressort d Horizon La garantie exclut les d fauts esth tiques ou les d fauts provoqu s par des cas de force majeure une manipulation incorrecte du produit une utilisation incorrecte ou commerciale de ce dernier ou encore des modifications de quelque nature qu elles soient La garantie ne couvre pas les d gats r sultant d un montage ou d une manipulation erron s d accidents ou encore du fonctionnement ainsi que des tentatives d entretien ou de r paration non effectu es par Horizon Les retours effectu s par le fait de l acheteur directement Horizon ou l une de ses repr sentations nationales requi rent une confirmation crite Limitation des d gats Horizon ne saurait tre tenu pour responsable de dommages cons quents directs ou indirects de pertes de revenus ou de pertes commerciales li
8. precauzioni per la sicurezza In caso contrario si potreb bero procurare incendi danni o ferite Componenti Usare solo componenti compatibili Se ci fossero dubbi riguardo alla compatibilit opportuno far riferimento alle istruzioni relative al prodotto o ai componenti oppure rivolgersi al reparto Horizon Hobby di competenza Volo Per sicurezza volare solo in aree molto ampie Meglio se si va su campi volo autorizzati per modellismo Consul tare le ordinanze locali prima di scegliere una ubicazione Elica Tenere gli oggetti liberi vestiti penne cacciaviti ecc lontano dall elica prima che vi restino impigliati Bisogna fare attenzione anche con le mani perch c il rischio di ferirsi anche gravemente Batterie Quando si maneggiano o si utilizzano le batterie bisogna attenersi alle istruzioni del costruttore il rischio di procurare incendi specialmente con le batterie LiPo con danni e ferite serie Piccole parti Questo kit comprende delle parti di piccole dimensioni e non lo si pu lasciare incustodito se c la presenza di bambini che li possono inghiottire e rimanere soffocati o intossicati SAFE OPERATING RECOMMENDATIONS nspect your model before every flight to ensure it is airworthy Be aware of any other radio frequency user who may present an interference problem Always be courteous and respectful of other users in your selected flight area e Choose an area clear of obstacles
9. achat une description d taill e des d fauts ainsi qu une liste de tous les l ments distincts envoy s Nous avons de plus besoin d une adresse compl te d un num ro de t l phone pour demander des renseignements et d une adresse de courriel Garantie et r parations Les demandes en garantie seront uniquement trait es en pr sence d une preuve d achat originale manant d un revendeur sp cialis agr sur laquelle figurent le nom de l acheteur ainsi que la date d achat Si le cas de garantie est confirm le produit sera r par Cette d cision rel ve uniquement de Horizon Hobby R parations payantes En cas de r paration payante nous tablissons un devis que nous transmettons votre revendeur La r paration sera seulement effectu e apr s que nous ayons recu la confirmation du revendeur Le prix de la r paration devra tre acquitt au revendeur Pour les r parations payantes nous facturons au minimum 30 minutes de travail en atelier ainsi que les frais de r exp dition En l absence d un accord pour la r paration dans un d lai de 90 jours nous nous r servons la possibilit de d truire le produit ou de l utiliser autrement Attention nous n effectuons de r parations payantes que pour les composants lectroniques et les moteurs Les r parations touchant la m canique en particulier celles des h licopt res et des voitures radiocommand es sont extr mement co teuses et doivent par cons quen
10. and large enough to safely accomodate your flying activity e Make sure this area is clear of friends and spectators prior to launching your aircraft e Be aware of other activities in the vicinity of your flight path that could cause potential conflict e Carefully plan your flight path prior to launch e Abide by any and all established AMA National Model Aircraft Safety Code EMPFEHLUNGEN ZUM SICHEREN BETRIEB e berpr fen Sie zur Flugtauglichkeit ihr Modell vor jedem Flug Beachten Sie andere Piloten deren Sendefrequenzen ihre Frequenz st ren k nnte Begegnen Sie anderen Piloten in ihrem Fluggebiet im mer h flich und respektvoll e Wahlen Sie ein Fluggebiet dass frei von Hindernissen und groB genug ist e Stellen Sie vor dem Start sicher dass die Flache frei von Freunden und Zuschauern ist Beobachten Sie den Luftraum und andere Flugzeuge Objekte die ihren Flugweg kreuzen und zu einem Konflikt f hren k nnten Planen Sie sorgf ltig ihren Flugweg vor dem Start CONSIGNES DE S CURIT CONCERNANT L UTILISATION nspectez votre mod le avant chaque vol Surveillez les fr quences radio utilis es proximit Soyez toujours courtois et respectueux des autres utilisateurs de la zone de vol Choisissez une zone d gag e de tout obstacle et suf fisamment grande pour voler en toute s curit e Contr lez que la zone est libre de spectateurs avant de lancer votre mod le Soyez
11. danni alla pro priet fisica o possono omportare un elevata possibilit di provocare ferite superficiali Ulteriori precauzi oni per la sicurezza e avvertenze Almeno 14 anni Non un giocattolo A AVVERTENZA Leggere TUTTO il manuale di istruzioni e prendere familiarita con le caratteristiche del prodotto prima di farlo funzionare Un utilizzo scorretto del prodotto pu causare danni al prodotto stesso alle persone o alle cose provocando gravi lesioni Questo un prodotto di hobbistica sofisticato e NON un giocattolo necessario farlo funzionare con cautela e responsabilit e avere conoscenze basilari di meccanica Se questo prodotto non utilizzato in maniera sicura e responsabile potrebbero verificarsi lesioni o danni al prodotto stesso o ad altre propri et Non un prodotto adatto a essere utilizzato dai bambini senza la diretta supervisione di un adulto Non tentare di smontare il prodotto di utilizzare componenti incompatibili o di potenziarlo in alcun modo senza previa approvazione di Horizon Hobby Inc Questo manuale contiene le istruzioni per un funzion amento e una manutenzione sicuri fondamentale leggere e seguire tutte le istruzioni e le avvertenze del manuale prima di montare configurare o far funzionare il Prodotto al fine di utilizzarlo correttamente e di evitare danni o lesioni gravi Come usare il manuale Questo manuale diviso in sezioni per rendere pi facile la comprensione del montag gi
12. la connexion du syst me PRIMA DI INIZIARE IL MONTAGGIO Togliere tutti i pezzi dalla scatola Verificare che la fusoliera l ala e i piani di coda non siano danneggiati e Se si trovano parti danneggiate contattare il negozio da cui stato acquistato Se si trovano delle grinze nella ricopertura si possono togliere usando una pistola ad aria calda HAN100 e guanto per ricopertura HAN150 oppure un ferro per ricopertura HAN101 con la sua calza di protezione HAN141 Usare cautela quando si lavora in aree del rivestimento dove ci sono dei colori sovrapposti per evitare la loro separazione e Caricare le batterie del trasmettitore e del ricevitore e Centrare stick e trim sul trasmettitore e Con una radio computerizzata creare una nuova memoria per questo modello e Facendo riferimento alle istruzioni del radiocomando connettere bind trasmettitore e ricevitore e La procedura di connessione va ripetuta una volta regolate le corse per evitare che i servi vadano a fine corsa ATTENZIONE Ripetere la procedura di connessione una volta regolate le corse per evitare che i servi vadano a fine corsa AILERON SERVO TRAY INSTALLATION e Mark the servo hatch mounting locations onto the wing Using a drill and 1 16 inch bit drill the marked locations Run the screws in and out of the mounting locations and apply thin CA to the holes to strengthen the wall 13 AILERON SE
13. name and address or AMA number of the owner on the inside or affixed to the outside of the model aircraft This does not apply to model aircraft flown indoors g Not operate aircraft with metal blade propellers or with gaseous boosts except for helicopters operated under the provisions of AMA Document 555 h Not operate model aircraft while under the influence of alcohol or while using any drug which could adversely affect the pilot s ability to safely control the model 98 i Not operate model aircraft carrying pyrotechnic devices which explode or burn or any device which propels a projec tile or drops any object that creates a hazard to persons or property Exceptions Free Flight fuses or devices that burn producing smoke and are securely attached to the model aircraft during flight Rocket motors using solid propellant up to a G series size may be used provided they remain attached to the model during flight Model rockets may be flown in accordance with the National Model Rocketry Safety Code but may not be launched from model aircraft Officially designated AMA Air Show Teams AST are autho rized to use devices and practices as defined within the Team AMA Program Document AMA Document 718 j Not operate a turbine powered aircraft unless in compli ance with the AMA turbine regulations AMA Document 3510 4 Model aircraft will not be flown in AMA sanctioned events air shows or model demonstrati
14. per hobbistica con lama numero 11 Use a pencil Verwenden Sie einen Bleistift Utilisez un crayon papier Usare una matita Use a felt tipped pen Verwenden Sie einen Faserstift Utilisez un feutre fin effacable Usare un pennarello TABLE OF CONTENTS IEN Assembly Symbol Guide Specifications Contents of Kit and Parts Listing Replacement Parts Required Items s ssssssssssneeisesnieesneeeenen Optional Items s nnnnnnnnnsnnsansansaesaeneeeaeeae Required Tools Before Starting Assembly n Assembly Aileron Servo Tray Installation 13 Aileron Servo Installation and Hinge Line Sealing 1 Landing Gear and Wheel Pants Installation 27 Rudder and Tail Gear Installation 31 Rudder Servo and Pull Pull Cable Installation 34 Elevator Servo and Stab Installation 39 Engine Dome Preparation DA 120 45 Ignition Module and Battery Installation 48 Throttle Servo Installation 49 Receiver Pack Installation for DA 120 Stock Muffler TT 56 Ignition Regulator and Switch Installation 58 Fuel Tank Installation for Stock Muffler 60 Engine Dome Installation 63 Cowl Preparation for Installation Canister Installation Option Receiver Installation Canopy Installation C
15. servi ma soltanto come ultima risorsa Si raccomanda vivamente di rifare il binding del radiocomando dopo che si sono fatte tutte le regolazioni Questo evita che i servi si possano muovere a fine corsa prima che trasmettitore e ricevitore siano connessi 91 PREFLIGHT CHECKLIST 92 Charge the transmitter receiver and motor battery for your airplane Use the recommended charger supplied with your radio system Following the instructions provided with the radio Charge the radio system the night before each flying session Charge transmitter and receiver batteries using only included or manufacturer recommended chargers Follow all manufacturer s instructions for your electronic components Check the radio installation and make sure all control surfaces aileron elevator rudder and throttle move correctly i e the correct direction and with the recommended throws Check all the hardware control horns servo horns and clevises to make sure they are secure and in good condition Prior to each flying session and especially with a new model perform a range check of your radio system See your radio manual for the recommended range and instructions for your particular radio system Run the motor With the model securely anchored repeat the range check procedure The range should not be significantly affected If it is do not attempt to fly Remove the radio equipment and have it inspected by the manufacturer
16. zu erweitern Diese Bedienungsanleitung enthalt Anweisungen f r Sicherheit Betrieb und Wartung Es ist unbedingt notwendig vor Zusammenbau Einrichtung oder Verwendung alle Anweisun gen und Warnhinweise im Handbuch zu lesen und zu befolgen damit es bestimmungsgem betrieben werden kann und Sch den oder schwere Verletzungen vermieden werden ber diese Anleitung Diese Anleitung ist zur Vereinfachung des Zusammenbaues in Sektionen unterteilt Neben den Sektionen befinden sich K stchen L1 die es Ihnen leichter machen den Arbeitsschritt als erledigt abzuhaken Schritte mit einem Kastchen werden einmal durchgef hrt Schritte mit mehreren Kast chen erfordern Wiederholungen nach Anzahl der Kastchen Zum Beispiel rechte und linke Tragflache zwei Servos etc Bitte lassen Sie sich bei dem Bauen ausreichend Zeit und folgen den Anweisungen REMARQUE La totalit des instructions garanties et autres documents est sujette a modification a la seule discr tion d Horizon Hobby Inc Pour obtenir la documentation a jour rendez vous sur le site horizonhobby com et cliquez sur l onglet de support de ce produit Signification de certains termes sp cifiques Les termes suivants sont utilis s dans l ensemble du manuel pour indiquer diff rents niveaux de danger lors de l utilisation de ce produit REMARQUE Proc dures qui si elles ne sont pas suivies correctement peuvent entrainer des d gats mat riels ET ventuellement un faible ris
17. 0010 Apply thread lock to the screw and using a 2 5mm ball driver tighten the Ensure both wheels move with little friction Pass the 5mm bolt through the washer and apply thread lock Using a 4 5mm wheel pant to the landing gear hex driver tighten the landing gear bolts to the fuselage 30 RUDDER AND TAIL GEAR INSTALLATION e e e L11 Mate the rudder hinges with the hinges on the fuselage Slowly and carefully insert the hinge rod into the hinges until it is flush with Temporarily mount the phenolic T bracket so that the spring holes line up with the bottom of the rudder the rudder control horn pivot point Using a felt pen mark the locations 31 RUDDER AND TAIL GEAR INSTALLATION e e e Drill marked locations using a 1 8 inch drill bit Run the screws in and out and apply thin CA to the holes to harden the wall Temporarily mount the tail gear as forward as possible Be careful not to miss tbklEUlleKYd amp I IIO OOOOO P Once CA is dry mount the T bracket the wood block location that tail gear will be mounted on Using a felt pen mark the screw mounting locations 32 RUDDER AND TAIL GEAR INSTALLATION e e Drill marked locations using a 1 8 inch drill bit Run the screws in and out Apply some thin CA in the holes and allow time for Install the gear when CA is dried Hook up the springs to the T fitting and tille
18. 2 THROTTLE SERVO INSTALLATION e e e Apply thread lock to engine bolts and mount the engine on the 1 inch stand Pass the rod through the engine dome Connect the ball link to the engine Add a piece of fuel tubing to the shaft of the clevis to secure the clevis at final offs throttle arm stage of installation 53 THROTTLE SERVO INSTALLATION e e e L116 L117 0118 Temporarily attach an 1 inch servo arm to servo and line up the arm with the Drill the dome for servo tray mounting locations using 3 32 inch and 7 64 Temporarily mount the servo tray and connect the throttle servo arm to the throttle rod by moving the throttle tray Using a felt pen mark the tray location inch drill bits servo Using pin vise mark the mounting locations 54 THROTTLE SERVO INSTALLATION e e L119 L120 L121 Temporarily power up the servo to the receiver adjust the throttle travel Make Once satisfied remove the tray and apply thread lock to servo arm center Mount the throttle servo tray using M3x16mm screws Finalize the installation all necessary changes for linkage length and servo arm Make sure it is bind screw and mount the arm Apply servo tape to the back of the throttle servo by moving the piece of fuel tubing over the clevis free If needed enlarge the hole for throttle rod in the dome tray as shown in the picture above 59 RECEIVER PACK INSTALLATION FOR
19. AGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Further in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting li ability If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product purchaser is advised to return the Product immediately in new and unused condition to the place of purchase Law These terms are governed by Illinois law without regard to conflict of law principals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice WARRANTY SERVICES Questions Assistance and Services Your local hobby store and or place of purchase cannot provide warranty support or service Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answ
20. AN520007 Wheel Pants QQ Yak 54 2 6m Comp HAN520008 Wing Tube QQ Yak 54 2 6m Comp o o uoowwnro m HAN520009 Stabilizer Tube QQ Yak 54 2 6m Comp 10 HAN520010 Cowling QQ Yak 54 2 6m Comp 11 HAN520011 Motor Dome Firewall QQ Yak 54 2 6m Comp 12 HAN520012 Hatch without Canopy QQ Yak 54 2 6m Comp 13 HAN520013 Canopy QQ Yak 54 2 6m Comp 14 HAN520026 Rudder Pin Brass Tube QQ Yak 54 2 6m Comp 15 HAN520028 Wing amp Stab Bags QQ Yak 54 2 6m Comp REQUIRED ITEMS e ERFORDERLICHE TEILE e EL MENTS REQUIS e ARTICOLI NECESSARI Part English Deutsch Francais Italiano SPMAR12120 AR12120 12 CH DSMX PowerSafe Receiver 1 AR12120 12 CH DSMX PowerSafe Empfanger 1 R cepteur PowerSafe AR12120 12 voies DSMX 1 Ricevitore PowerSafe DSMX AR12120 12 CH 1 JRPS8911HV DS88911HV Ultra Torque Servo Rudder 1 Eleva DS8711 Ultra Torque Servo Seitenruder 1 Servo couple lev DS8711 d rive 1 Servo a coppia elevata DS8711 timone 1 tors 2 Ailerons 4 JRPS8917HV DS8917HV Ultra Speed Servo Throttle 1 SPMVR5203 Ignition Regulator 1 Z ndungsregler 1 Module d allumage 1 Regolatore di accensione 1 JRPA004 JR Switch With Charge Jack HAN9160 Single Alum Adj Servo Arm 2 inch 4 Sevorarm 1 1 2 Zoll 4 Bras de servo r glable en aluminium 38 mm 4 Braccio servo regolabile in alluminio singolo da 38 1 mm 4 HAN4963 Dbl
21. ATION FOR STOCK MUFFLER L11 Mark the fuel line exit to the carburetor inside of the dome Using a drill and Place a piece of foam under the tank Install the fuel tank using the tie wraps Attach the Hangar 9 fuel filter to the line 1 8 inch 7 32 inch drill bits and drill through the marked location included by passing them over the tank tray and into the slots 60 FUEL TANK INSTALLATION FOR STOCK MUFFLER 14 Using a drill and 1 8 inch and 7 32 inch drill bits drill through location shown Pass the vent line through the hole Mark the location shown in above picture This is for the fill line Make sure it in above picture for fuel vent line Pass the vent line through the hole doesn t interfere with wing location 61 FUEL TANK INSTALLATION FOR STOCK MUFFLER Using a drill and 1 8 inch drill bit drill through the marked location Using a sanding drum and a drill or a rotary tool open up the hole to 3 8 inch Install the Hangar fuel filler and T 62 ENGINE DOME INSTALLATION e e o L11 Install the vibration dampeners on the dome Insert the clear tubes in the Line up the dome with the fuselage and slowly working the dome into the Insert the washer over the studs and using a 7mm nut driver tighten the nuts center of the vibration dampeners studs If any of the clear inserts came out continue installing th
22. Alum Adj Spline Servo Arm 4 inch 1 Servoarm doppelt 3 Zoll 1 Bras de servo r glable double en aluminium 76 Braccio servo chiavetta regolabile in alluminio dop mm 1 pio da 76 2 mm 1 JRPA102 24 inch Servo Extension 1 Servoverl ngerung 36 Zoll 2 Rallonge de servo 91 cm 2 Prolunga servo da 914 4 mm 2 JRPA099 18 inch Servo Extension 2 Servoverl ngerung 18 Zoll 2 JRPA095 6 inch Servo Extension 6 Servoverl ngerung 6 Zoll 1 Rallonge de servo 15 cm 1 Prolunga servo da 152 4 mm 1 EFLAEC311 6 inch EC3 Extension Lead 2 SPMB2000LP LiPo Ignition Pack 2000mah 1 LiPo Z ndakku 2000mAh 1 Batterie Li Po d allumage 2 000 mAh 1 Pacco per accensione LiPo 2000 mah 1 SPM4000LP LiPo Receiver Pack 4000mah 2 LiPo Empfangerakku 4000 mAh 2 Batterie Li Po de r ception 4 000 mAh 2 Pacco per ricevitore LiPo 4000 mah 2 PAAPTO8 Thin CA D nnfl ssiger Sekundenkleber Colle CA cyanoacrylate fine CA liquida PAAPTO2 Medium CA Mitellfl ssiger Sekundenkleber Colle CA cyanoacrylate moyenne CA medio PAAPT40 Z Poxy Finishing Resin PAAPT39 30 minute Epoxy 30 Minuten Epoxidharzkleber Colle Epoxy 30 minutes Epoxy 30 minuti PAAPT42 Threadlock Schraubensicherung Frein filet Adesivo frenafiletti PAAPT56 Canopy Glue Kleber f r Kabinenhaube Colle liquide universelle transparente Vitrages Colla per capottina PAR8044 Pro Servo Tape Pro Servoklebeband Ruban adh sif pour servo qualit professionnelle Nastro pro per servi HAN115 Fuel Dot Filler w
23. Composite QQ Yak 54 2 6m ere Instruction Manual Bedienungsanleitung Manuel d utilisation Manuale di Istruzioni NOTICE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby Inc For up to date product literature visit horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND a little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury Age Recommendation Not for children under 14 years This is not a toy A WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate
24. DA 120 STOCK MUFFLER SETUP e e o L11 12 Apply masking tape to both sides of each battery Apply two strips of servo tape on one side of each battery Using medium CA glue a piece of hook and loop to the other side of each battery 56 RECEIVER PACK INSTALLATION FOR DA 120 STOCK MUFFLER SETUP e e o 14 15 Overlap about 4 inches of hook and look straps provided Pass the straps through the lightening hole on the tray as shown in the Mount the batteries with servo tape sitting on the tray and hook and look side picture on top Wrap the hook and look strap over the battery and ensure that hook and loop locks on top Note Battery locations shown are based on the equip ment that this manual is recommending and is built 57 IGNITION REGULATOR AND SWITCH INSTALLATION e e e L11 12 Apply masking tape to the back of ignition regulator Apply a piece of servo tape to the masking tape Mount the regulator in front of the receiver battery 58 IGNITION REGULATOR AND SWITCH INSTALLATION e e e 14 Using a felt pen trace the area where the ignition switch is to be installed Using a hobby knife cut out the traced area If need be change blade often Install the switch A piece of plywood from the servo trays could be used for backing 59 FUEL TANK INSTALL
25. LLATION DU R CEPTEU DU R CEPTEUR INSTALLAZIONE DEL RICEVITORE D4 D6 Using medium CA glue opposite side of hook and loop to the back of the Once CA is dry mount the receiver Use servo tape to install the remote receivers The Picture above shows the receiver over the masking tape location of remote receiver 1 74 RECEIVER INSTALLATION EINBAU DES EMPF NGERS INSTALLATION DU R CEPTEU DU R CEPTEUR INSTALLAZIONE DEL RICEVITORE L19 Location of the remote receiver 2 Location of the remote receiver 3 Location of the remote receiver 4 CANOPY INSTALLATION L11 Using an 80 grit sand paper go over the canopy frame and rough the contact Carefully cut the edges of the canopy Using 2 masking tape or mask paper mask the entire canopy location with the canopy for good adhesion Also sand down any high spots at the seams or anywhere else to be smooth and flush with the surrounding Note Canopy gets scratched easily be careful while cutting and moving the area Use acetone and clean the surfaces canopy 16 CANOPY INSTALLATION 14 Using mask paper and masking tape mask the inside of the canopy Follow the mold line and cut anything outside of the mold line by 1 16 inch Back of the canopy has two mold lines Cut anything outside the outer sec ond mold line Black solid lines show the two mold lines
26. ON SERVO INSTALLATION AND HINGE LINE SEALING LILI7 Temporarily power up the servos by connecting them to the receiver With radio sub trim at 0 mount the servo arm such that it is perpendicular to the servo Use sub trim if necessary Schalten Sie die Servos vor bergehend ein indem Sie sie an den Empf nger anschlieBen Stellen Sie das Subtrimm f r die des Senders auf 0 und mon tieren Sie den Servoarm rechtwinklig zu dem Servo Verwenden Sie dazu bei Bedarfdie Subtrimmfunktion Raccordez les servos au receveur pour les alimenter temporairement Mettez les commandes sub trim au neutre puis assemblez le palonnier du servo de telle sorte qu il se retrouve perpendiculaire au servo Utilisez le sub trim r glages fins si n cessaire Alimentare temporaneamente i servi collegandoli al ricevitore Con il sub trim della radio su 0 montare il braccio del servo perpendicolarmente al servo Se necessario utilizzare il sub trim 0108 Apply thread lock to the servo arm center screw and make sure to use the Install both set screws on the side of the servo arm lock washer provided with servo accessories Geben Sie etwas Schraubensicherungslack auf die mittlere Schraube des Servoarms Legen Sie eine der Unterlegscheiben ein die im Zubeh r des Servos enthalten sind Appliquez du frein filet sur le filetage central du palonnier du servo puis assurez vous d utiliser la rondelle crant e fo
27. RVO TRAY INSTALLATION e LILIA LILIS Q Remove pieces that are marked in picture above Using an 80 grit sandpaper sand the tabs off the tray pieces Apply masking tape to the back of servo hatch to prevent it from being scratched while working on it Mark the center of the servo hatch and draw a line 14 AILERON SERVO TRAY INSTALLATION e LILI7 L1LI8 BIS GETT LL i ttrixtritrtuttmtatatano o6 Measure 27mm from the edge of the servo hatch and mark the location on Draw two lines just outside the mounting locations Servo tray needs to be Mark the center of the servo tray both sides confined between these two lines 15 AILERON SERVO TRAY INSTALLATION e 0010 0011 0012 Use and 80 grit sandpaper and thoroughly rough up the hatch then use Use hobby knife and scratch the surface of all the pieces of the servo tray Servo tray piece shown in above picture needs to be in the center of the servo hobby knife and scratch the surface really well Then clean the surface using that will be glued together Using Acetone thoroughly clean the surfaces hatch just below the 27mm mark and between the marked boundary lines acetone These three steps are very important for proper bonding just outside the mounting locations Using Mercury M100XF CA glue the servo tray piece to the hatch Apply pressure and make sure it stays vertical until CA dries Do not use accelerat
28. UNKT Ein wichtiger Schritt zur Vorbereitung des Flugzeugs f r den Flug ist die Ausbalancierung des Modells 1 Befestigen Sie die Flugelflachen am Rumpf Stellen Sie sicher dass die Kabel von dem Querruder mit dem richtigen Kabel am Empf nger verbunden sind Achten Sie darauf dass die Kabel nicht aus dem Rumpf aus treten bevor Sie die Fl gelbolzen anziehen Ihr Modell sollte fertig montiert und flugbereit sein bevor Sie es ausbalancieren 2 3 Ihr Modell muss bereits fertig montiert und flugbereit sein wenn Sie es ausbalancieren Um Ihr Modell auszubalancieren stellen Sie das Flugzeug aufrecht hin und st tzen Sie es mit den Fingern oder auf einem im Handel erh ltlichen Balancierst nder an den markierten Punkten am Fl gel Dies ist der korrekte Balancepunkt f r Ihr Modell 4 Wenn die Komponenten wie in der Anleitung gezeigt eingebaut wurden sollte der Schwerpunkt sehr nahe an der angegebenen Position liegen Wenn der Bug des Flugzeugs nach unten h ngt verschieben Sie die Akkus in dem Flugzeug ein wenig nach hinten Wenn das Heck nach unten h ngt legen Sie in die Nase des Flugzeugs Gewichte ein Sie erhalten selbstklebende Gewichte HAN3626 die f r diesen Zweck geeignet sind bei Ihrem Modellbauhandler A ACHTUNG Sie m ssen den Schwerpunkt des Flugzeugs justieren und das Modell richtig ausbalancie ren bevor Sie es fliegen CENTRE DE GRAVIT Une des op rations essentielles quant la pr paration de
29. Verk ufe an dritte werden von dieser Garantie nicht gedeckt Garantieanspr che werden nur angenommen wenn ein g ltiger Kaufnachweis erbracht wird Horizon beh lt sich das Recht vor diese Garantiebestimmungen ohne Ank ndigung zu ndern oder modifizieren und widerruft dann bestehende Garantiebestimmungen b Horizon bernimmt keine Garantie f r die Verkaufbarkeit des Produktes die F higkeiten und die Fitness des Verbrauchers f r einen bestimmten Einsatzzweck des Produktes Der K ufer allein ist daf r verantwortlich zu pr fen ob das Produkt seinen F higkeiten und dem vorgesehenen Einsatzzweck entspricht c Anspr che des Kaufers Es liegt ausschlieBlich im Ermessen von Horizon ob das Produkt bei dem ein Garantiefall festgestellt wurde repariert oder ausgetauscht wird Dies sind die exklusiven Anspr che des Kaufers wenn ein Defekt festgestellt wird Horizon beh lt sich vor alle eingesetzten Komponenten zu pr fen die in den Garantiefall einbezogen werden k nnen Die Entscheidung zur Reparatur oder zum Austausch liegt nur bei Horizon Die Garantie schlieBt kosmetische Defekte oder Defekte hervorgerufen durch h here Gewalt falsche Behandlung des Produktes falscher Einsatz des Produktes kommerziellen Einsatz oder Modifikationen irgendwelcher Art aus Die Garantie schlieBt Sch den die durch falschen Einbau falsche Handhabung Unfalle Betrieb Service oder Reparaturversuche die nicht von Horizon ausgef hrt wurden
30. Versagen das Produkt sicher und umsichtig zu betreiben kann zu Verletzungen von Lebewesen und Sachbesch digungen erheblichen AusmaBes f hren Dieses Produkt ist nicht f r den Gebrauch durch Kinder ohne die Aufsicht eines Erziehungsberechtigten vorgesehen Die Anleitung enthalt Sicherheitshinweise und Vorschriften sowie Hinweise f r die Wartung und den Betrieb des Produktes Es ist unabdingbar diese Hinweise vor der ersten Inbetriebnahme zu lesen und zu verstehen Nur so kann der falsche Umgang verhindert und Unf lle mit Verletzungen und Beschadigungen vermieden werden Fragen Hilfe und Reparaturen Ihr lokaler Fachhandler und die Verkaufstelle k nnen eine Garantiebeurteilung ohne R cksprache mit Horizon nicht durchf hren Dies gilt auch f r Garantiereparaturen Deshalb kontaktieren Sie in einem solchen Fall den H ndler der sich mit Horizon kurz schlieBen wird um eine sachgerechte Entscheidung zu f llen die Ihnen schnellst m glich hilft Wartung und Reparatur Muss Ihr Produkt gewartet oder repariert werden wenden Sie sich entweder an Ihren Fachhandler oder direkt an Horizon R cksendungen Reparaturen werden nur mit einer von Horizon vergebenen RMA Nummer bearbeitet Diese Nummer erhalten Sie oder ihr Fachhandler vom technischen Service Mehr Informationen dazu erhalten Sie im Serviceportal unter www Horizonhobby de oder telefonisch bei dem technischen Service von Horizon Packen Sie das Produkt sorgf ltig ein Beachten S
31. a garantie et la r paration ssssennnnnee 91 INDICE Elementi di fissaggio sss 6 Guida ai simboli di assemblaggio 7 Specifiche ile ae 9 Contenuto del kit ed elenco parti 9 Parti di ricambio sss 9 Articoli necessari i 10 Articoli opzionali sn 10 Strumenti richiesti lcd di IN eM IET 11 Prima dell assemblaggio iniziale 12 Assemblaggio Installazione carrello e supporti montanti 13 Installazione cerniere e squadrette timone 17 Installazione servi elevatore squadrette e stabilizzatore eeeeeneeeererereerererrererrrrererrerer 22 Installazione servo timone e comandi 29 Installazione del gruppo ruotino di coda 38 Installazione degli interruttori e dei regolatori 40 Installazione del ricevitore 42 Installazione delle batterie del ricevitore 45 Installazione modulo di accensione batteria e interruttore eennnne 49 Installazione del motore e del suo servo 51 Installazione serbatoio e tubetti carburante 57 Preparazione della carenatura e installazione del SIGN ZIALONG EE 59 Installazione servi nell ala e cerniere alettoni 63 Installazione dei montanti delle ali 71 Installazione montanti s
32. aften Verletzung zur Folge AVERTISSEMENTS RELATIFS LA S CURIT Lisez et suivez toutes les instructions relatives la s curit avant utilisation Une utilisation inappropri e peut entrainer un incendie de graves blessures et des d gats mat riels Composants Utilisez uniquement des composants compatibles Si vous avez des questions concernant la compatibilit r f rez vous ce manuel ou contactez le service technique Horizon Hobby Le vol Volez uniquement dans des zones d gag es pour un maximum de s curit Il est recommand d utiliser les pistes des clubs d a romod lisme Consultez votre mairie pour conna tre les sites autoris s L h lice Gardez loign s tous les l ments qui pourraient tre attrap s par l h lice Cela inclut les v tements larges ou les objets comme des outils par exemple Gardez toujours vos mains distance pour viter tout risque de blessures Les batteries Suivez toujours les instructions du fabricant de vos bat teries Une mauvaise manipulation d une batterie Li Po peut entrainer un incendie causant de graves d gats mat riels et des blessures corporelles Petites pi ces Ce kit contient des petites pi ces qui ne doivent pas tres laiss es la port e des enfants ces pi ces sont dangereuses pour eux et peuvent entrainer de graves blessures AVVERTIMENTI E PRECAUZIONI PER LA SICUREZZA Prima dell uso leggere attentamente tutte le istruzioni e le
33. allazione radio accertandosi che tutte le superfici di controllo alettoni elevatore timone e motore si muovano nel verso corretto e con la giusta corsa Controllare tutte le squadrette di controllo squadrette dei servi e forcelle per accertarsi che siano ben fis sate e in buone condizioni Prima di ogni sessione di volo e specialmente con un modello nuovo eseguire una prova di portata del radiocomando Per ulteriori spiegazioni si veda il manuale del radiocomando Avviare il motore e con il modello assicurato saldamente al suolo ripetere la prova di portata del radiocomando che non dovrebbe sostanzialmente differire da quella precedente Se cosi non fosse evitare di andare in volo Fare le opportune verifiche sull impianto radio ed eventualmente inviare il tutto al servizio assistenza DAILY FLIGHT CHECKS Check the battery voltage of the transmitter battery Do not fly below the manufacturer s recommended voltage To do so can crash your aircraft When you check these batteries ensure you have the polarities correct on your expanded scale voltmeter Check all hardware linkages screws nuts and bolts prior to each day s flight Ensure that bind ing does not occur and that all parts are properly secured Ensure all surfaces are moving in the proper manner Perform a ground range check before each day s flying session Prior to starting your aircraft turn off your transmitter then turn it back on Do this eac
34. anopy Trim Installation Fuselage Cutout for Wing Extensions 85 Optional Side Force Generator Installation 86 Sticker Installation Control Surface Measurement Center Of Gravity zes Control Throws eenn Preflight Checklist Daily Flight Checks General Flying E Limited Warranty Warranty And Service Contact Information 97 INHALTSVERZEICHNIS Halterung Symbolerkl rung f r den Zusammenbau 7 Spezifikationen sse Inhalt des Bausatzes Teileauflistung Ersatztelle i eee Ben tigte Artikel Optionale Artikel Ben tigte Werkzeuge sss Vorbereitung des Zusammenbaus Zusammenbau Zusammenbau von Fahrwerkstrebe und Strebenhalterung see 13 Zusammenbau der Seitenruderscharniere und des Ruderhomms n 17 Zusammenbau der H henruderservos des Rudernhorns und des Stabilisators 22 Einbau von H henruderservo und Pull Pull 29 Zusammenbau des Heckradsatzes 38 Einbau des Schalters und des Reglers 40 Einbau des Empf ngers 42 Einbau des Empf ngerakkus 45 Z ndmodul Akku und Schalter Zusammenbau 49 Motor und Gasgeber Servoeinbau 51 Zusammenbau von Benzintank und Leitungen 57 V
35. ateurs sese 22 Assemblage du c ble pull pull et du servo de la gouverne de direction 29 Fixation et montage de la roulette de queue 38 Installation des interrupteurs et des r gulateurs40 Installation du r cepteur 42 Installation des batteries du r cepteur 45 Installation du module d allumage des batteries et de l interrupteur correspondant 49 Installation du moteur et du servo de commande des gaz s s sssssssssienesisieresnsnrrreneereneee 51 Assemblage du r servoir et des durites pour le Carburarit 5 neces 57 Pr paration du capot et Installation des silencieux 59 Installation des servos des ailes et de la charni re de l aileron 63 Assemblage et installatione des haubans TUE Ti Fixation du c ble stabilisateur plan horizontal D M 75 Assemblage du tableau de bord 78 Installation des vitres lat rales et du pare brise 80 Montage et mise en place des si ges 82 Mise en place des d cors et autocollants ornant le bout des ailes et le fuselage 83 Assemblage de la porte d acc s bord 83 Centre de gravit Courses des commandes Check list de pr paration au vol Contr les des vols quotidiens Conditions habituelles de vol Garantie limit e sse Coordonn es des services pour l
36. aus R cksendungen durch den Kaufer direkt an Horizon oder eine seiner Landesvertretung bed rfen der Schriftform Schadensbeschr nkung Horizon ist nicht f r direkte oder indirekte Folgesch den Einkommensausfalle oder kommerzielle Verluste die in irgendeinem Zusammenhang mit dem Produkt stehen verantwortlich unabh ngig ab ein Anspruch im Zusammenhang mit einem Vertrag der Garantie oder der Gew hrleistung erhoben werden Horizon wird dar ber hinaus keine Anspr che aus einem Garantiefall akzeptieren die ber den individuellen Wert des Produktes hinaus gehen Horizon hat keinen Einfluss auf den Einbau die Verwendung oder die Wartung des Produktes oder etwaiger Produktkombinationen die vom K ufer gew hlt werden Horizon bernimmt keine Garantie und akzeptiert keine Anspr che f r in der folge auftretende Verletzungen oder Beschadigungen Mit der Verwendung und dem Einbau des Produktes akzeptiert der K ufer alle aufgef hrten Garantiebestimmungen ohne Einschr nkungen und Vorbehalte Wenn Sie als Kaufer nicht bereit sind diese Bestimmungen im Zusammenhang mit der Benutzung des Produktes zu akzeptieren werden Sie gebeten dass Produkt in unbenutztem Zustand in der Originalverpackung vollstandig bei dem Verkaufer zur ckzugeben Sicherheitshinweise Dieses ist ein hochwertiges Hobby Produkt und kein Spielzeug Es muss mit Vorsicht und Umsicht eingesetzt werden und erfordert einige mechanische wie auch mentale Fahigkeiten Ein
37. check the blister location Using a rotary tool and sanding drum smooth out the edges make sure not drill and 1 16 inch drill bit to cross the traced line 67 COWL PREPARATION FOR STOCK MUFFLER e 0112 113 014 Clean the cowl using acetone Glue the blister from inside of the cowl using goop or epoxy Use masking tape to hold in place 68 COWL PREPARATION FOR STOCK MUFFLER e L115 L116 L117 Clean excess glue with alcohol swab Cut the mufflers by 3 4 inch to reduce the cowl cut out for stock muffler Dry fit the cowl often and open up the cowl as necessary Make sure not to installation Use the already cut stack as a reference for muffler cut out force the cowl causing paint cracks The picture above shows the final result 69 CANISTER INSTALLATION OPTION e e This airplane is designed to accommodate diverse type of canisters An example of the MTW TD 75 is shown in the following pictures Headers used for this installation are MTW flex with 50 mm drop down Once canisters are installed use the battery trays provided in the kit and find the best place to mount them for proper CG It is important that proper location of the battery trays and batteries be found before gluing the trays 70 Glue the mount using micro balloon and epoxy Tri Stocks help secure the mount in place Vent line from the tank should go straigh
38. chtige Reparaturen nehmen wir nur f r Elektronik und Motoren vor Mechanische Reparaturen besonders bei Hubschraubern und RC Cars sind extrem aufwendig und m ssen deshalb vom Kaufer selbst vorgenommen werden 95 GARANTIE ET R PARATIONS Dur e de la garantie Garantie exclusive Horizon Hobby Inc Horizon garantit que le Produit achet le Produit sera exempt de d fauts mat riels et de fabrication sa date d achat par l Acheteur La dur e de garantie correspond aux dispositions l gales du pays dans lequel le produit a t acquis La dur e de garantie est de 6 mois et la dur e d obligation de garantie de 18 mois l expiration de la p riode de garantie Limitations de la garantie a La garantie est donn e l acheteur initial Acheteur et n est pas transf rable Le recours de l acheteur consiste en la r paration ou en l change dans le cadre de cette garantie La garantie s applique uniquement aux produits achet s chez un revendeur Horizon agr Les ventes faites des tiers ne sont pas couvertes par cette garantie Les revendications en garantie seront accept es sur fourniture d une preuve d achat valide uniquement Horizon se r serve le droit de modifier les dispositions de la pr sente garantie sans avis pr alable et r voque alors les dispositions de garantie existantes b Horizon n endosse aucune garantie quant la vendabilit du produit ou aux capacit s et la forme physique de
39. ci ed anche molto prevedibili Iniziare posando il modello a terra Controllare tutte le corse dei comandi accertandosi che tutti vadano nella giusta direzione Posizionare il trim del minimo fino ad avere un minimo moderato Rullare in pista fino alla po sizione controvento per il decollo Applicare gradualmente potenza contrastando la coppia con il timone La coda si alza quasi subito Dando tutto gas e aumentando la velocit basta dare poco comando di elevatore per far salire dolcemente il Super Decathlon per fare quota Appena si inizia la salita si pu lasciare il comando dell elevatore mantenendo un graduale rateo di salita fino a circa 30 metri Raggiunta questa quota trimmare il modello in modo da livellare il volo con circa il 60 di motore Si trover che il Super Decathlon ha un volo molto dolce e risponde ai comandi in modo molto graduale Questo modello in grado di eseguire tutte la manovre basiche di acrobazia come looping tonneau stalli d ala volo rovescio ecc Speriamo che possiate divertirvi con il Super Decathlon Hangar 9 cosi come abbiamo fatto noi LIMITED WARRANTY What this Warranty Covers Horizon Hobby Inc Horizon warrants to the original purchaser that the product purchased the Product will be free from defects in materials and workmanship at the date of purchase What is Not Covered This warranty is not transferable and does not cover i cosmetic damage ii damage due to acts
40. conscient des autres activit s aux alentours de votre vol afin d viter tout risque de conflit potentiel Planifiez votre vol avant de le commencer RACCOMANDAZIONI PER OPERARE IN SICUREZZA e Controllare attentamente il modello prima di ogni volo per accertarsi che sia idoneo Essere consapevoli che un altro utente della frequenza in uso potrebbe procurare delle interferenze Essere sempre cortesi e rispettosi nei confronti degli altri utilizzatori dell area in cui ci si trova Scegliere un area libera da ostacoli e abbastanza am pia da permettere lo svolgimento del volo in sicurezza Prima del volo verificare che l area sia libera da amici e spettatori Stare attenti alle altre attivit che si svolgono in vicinanza della vostra traiettoria di volo per evitare possibili conflitti Pianificare attentamente il volo prima di lanciare il modello Rispettare sempre scrupolosamente le regole stabilite dall associazione locale FASTENERS VERBINDUNGSELEMENTE EL MENTS DE FIXATION ELEMENTI DI FISSAGGIO M4 Washer MIND 4 40 x 5 8 inch M4 Unterlegscheibe M4 Rondelle M4 Rondelle M6 Washer M6 Unterlegscheibe M6 Rondelle M6 Rondelle M3 M4 M6 Locking nut M3 Stopmutter M3 Ecrou auto frein M3 dadi autobloccanti M3 nut M3 Mutter M3 Ecrou M3 Dadi 4 40 x 1 inch mm 6 32 x 172 inch 1 4 20 x 1 1 2 inch
41. d above Reference is the seam of control surface All measurements for low and high rates are given on page 91 89 CENTER OF GRAVITY An important part of preparing the aircraft for flight is properly balancing the model 1 Attach the wing panels to the fuselage Make sure to connect the leads from the aileron to the appropriate leads from the receiver Make sure the leads are not exposed outside the fuselage before tightening the wing bolts Your model should be flight ready before balancing 2 The recommended Center of Gravity CG location for your model is 210mm 220mm forward from the trailing edge of the aileron It is recommended to use 220mm for precision flight and 210 for 3D flight 3 When balancing your model make sure it is assembled and ready for flight Support the plane upright at the marks made on the wing with your fingers or a com mercially available balancing stand This is the correct balance point for your model 4 You should find the CG to be very close with the components installed as shown in this manual If the nose of your aircraft hangs low move batteries to the rear of the aircraft If the tail hangs low add weight to the nose of the aircraft Self stick weights HAN3626 are available at your local hobby store and work well for this purpose AN CAUTION You must adjust your aircraft s center of gravity and balance your model properly before attempting flights 90 DER SCHWERP
42. deg expo 45 Bas 15 deg expo 40 35 deg expo 45 D rive Droite 27 deg expo 35 Gauche 27 deg expo 35 Il s agit de mesures g n rales que nous avons obtenues en effectuant des essais en vol Vous pouvez essayer des d battements plus importants qui correspondent votre style de pilotage Les courses et les sub trims ne sont pas indiqu s car ils doivent tre r gl s suivant la convenance de chaque pi lote Installez toujours les bras de servos la perpendicu laire des servos Utilisez les sub trim en dernier recours pour r gler le neutre des servos Nous vous recommandons de r affecter votre radio quand tous les r glages de d battements sont effectu s Cela emp chera les servos d aller en but e lors de la connexion de l metteur et du r cepteur 4 Alettoni MIN MAX Su 19 deg expo 25 26 deg expo 30 Gi 11 5 deg expo 25 16 5 deg exp 30 Elevatore MIN MAX Su 15 deg expo 40 35 deg expo 45 Gi 15 deg expo 40 35 deg expo 45 Timone Destra 27 deg expo 35 Sinistra 27 deg expo 35 Queste misure sono indicazioni generali misurate nelle nostre prove in volo Si possono variare leggermente per adattarle al proprio stile di volo Le regolazioni delle corse e dei sub trim non sono men zionate perch ognuno se li regola in base alle proprie preferenze Montare sempre le squadrette a 90 rispetto alla linea centrale del servo sub trim si usano per centrare i
43. dimenti nelle corse dei comandi e che tutte le parti siano fissate bene Verificare che le superfici mobili si muovano nel verso giusto Eseguire una prova di portata a terra prima di una sessione di volo giornaliera Prima di avviare l aereo spegnere e riaccendere il trasmettitore Facendo questo tutte le volte ci si accorge se vi qualche interruttore critico inserito inavvertitamente perch in questo caso si attiva un allarme Verificare che tutti i trim siano nella giusta posizione Tutti i connettori dei servi e della batteria devono essere ben inseriti nelle prese del ricevitore Verifi care che l interruttore di accensione dell impianto ricevente si possa muovere liberamente in entrambe le direzioni 93 GENERAL FLYING Super Decathlon is a very docile model in the air and on the ground Takeoffs are easy and landings are slow and gentle and very predictable Begin by placing the model on the ground Check all control throws and ensure everything is traveling in the correct direction Move your idle trim up to a moderate idle Taxi into position on the runway facing into the wind Apply power slowly and steer with rudder The tail will come up very quickly As you apply full throttle and come to speed apply a slight amount of up elevator and the Super Decathlon should lift off gently and begin to climb upwards As you climb out release the elevator and maintain a gentle climb to about 100 feet of altit
44. driver install the ball link in the Using a pencil mark 23mm away from the center of the anti rotation pin Use a 1 8 inch drill bit and drill a pilot hole in the fuselage control horn hole in the fuselage 43 ELEVATOR SERVO AND STAB INSTALLATION 0016 0017 0018 Using a sanding drum with outside diameter of 5 16 inch enlarge the hole Pass the extension into the fuselage and leave the female lead outside If The stabilizer tube has R and L designation for right side and left side respec With this measurement only male connector of extension fits through the hole stabilizers will have to be removed for transportation use a commercially tively Plug the right stabilizer first into the stab tube and fuselage Using blue and female end won t fall inside the fuselage This helps if stabilizers need to available safety clip to secure the servo lead to extension otherwise use a thread lock install the stab screw through the bottom of the stab into the tube be removed for transportation heat shrink to secure the connector 44 ENGINE DOME PREPARATION DA 120 e e o L11 Engine dome has right thrust built into it There s a cross on the dome Extend these lines straight up and horizontal Measure 40mm up and down and 35mm left and right and mark the 4 mounting locations Temporarily mount the engine and make sure that marked locations line up with engi
45. e dome and If using a socket make sure not to overtighten the nuts Using a nut driver as insert the clear insert after dome is on the fuselage Apply some thread lock shown in the picture above is better to the studs 63 ENGINE DOME INSTALLATION e e o COWL PREPARATION FOR STOCK MUFFLER e e o 14 L11 Pass the fuel line coming off of the fuel filter through the engine dome and Using a felt pen mark the center of the cowl Using a felt pen draw a rectangle with width of 70mm connect to the engine carburetor Use a tie wrap to secure the line 64 COWL PREPARATION FOR STOCK MUFFLER e e L13 Using a rotary tool and cutting disk open up the front of the cowl Use a sand Carefully mount the cowl mark the spark plug cap contact location with the Trace the cowl blister on a piece of paper ing drum and smooth out the corners side of the cowl 65 COWL PREPARATION FOR STOCK MUFFLER e e 16 Use a copy machine and reduce the size to 87 Using a hobby knife cut the paper following the line Trace the reduced blister size on the cowl such that spark plug contact area is inside the blister 66 COWL PREPARATION FOR STOCK MUFFLER e e L19 Cut the blister location using a rotary tool and a cutting disk or a high speed Install the cow to ensure and
46. ements du manuel avant l assemblage le r glage et l utilisation ceci afin de manipuler correctement l appareil et d viter tout d gat mat riel ou toute blessure grave Utilisation du manuel Ce manuel est divis en sections pour vous aider comprendre plus facilement l assemblage Des cases L1 ont t plac es chaque tape Cela vous permet d avoir un suivi des tapes d j effectu es Les tapes avec une seule case ne sont faire qu une seule fois les tapes avec plusieurs cases sont r p ter Par exemple aile droite et aile gauche 2 servos etc Rappelez vous de prendre votre temps et de suivre les directions Tutte le istruzioni le garanzie e gli altri documenti pertinenti sono soggetti a cambiamenti a totale discrezione di Horizon Hobby Inc Per una documentazione aggiornata sul prodotto visitare il sito www horizonhobby com e fare clic sulla sezione Support per questo prodotto Significato dei termini particolari In tutta la documentazione relativa al prodotto sono utilizzati i seguenti termini per indicare vari livelli di potenziale pericolo durante il funzionamento AVVISO Procedure che se non sono seguite correttamente possono creare danni materiali E nessuna 0 scarsa possibilit di lesioni ATTENZIONE Procedure che se non sono seguite correttamente possono creare danni materiali E pos sibili gravi lesioni AVVERTENZA Procedure che se non debitamente seguite espongono alla possibilit di
47. ent on Amateur Band frequen cies RC model aircraft will not operate within three 3 miles of any pre existing flying site without a frequency management agreement AMA Documents 922 Testing for RF Interfer ence 923 Frequency Management Agreement With the exception of events flown under official AMA Competition Regulations excluding takeoff and landing no powered model may be flown outdoors closer than 25 feet to any individual except for the pilot and the pilot s helper s located at the flight line Under no circumstances may a pilot or other person touch a model aircraft in flight while it is still under power except to divert it from striking an individual This does not apply to model aircraft flown indoors RC night flying requires a lighting system providing the pilot with a clear view of the model s attitude and orientation at all times The pilot of a RC model aircraft shall a Maintain control during the entire flight maintaining visual contact without enhancement other than by corrective lenses prescribed for the pilot b Fly using the assistance of a camera or First Person View FPV only in accordance with the procedures outlined in AMA Document 550 Please see your local or regional modeling association s guidelines for proper safe operation of your model aircraft FAA INFORMATION FOR HORIZON MANUALS Prior to flying contact your local or regional modeling organiza tion
48. er maggiori informazioni sui punti di riciclaggio si invita a contattare l ufficio locale competente il servizio di smaltimento rifiuti o il negozio presso il quale stato acquistato il prodotto 97 AMA NATIONAL MODEL AIRCRAFT SAFETY CODE Effective January 1 2011 A GENERAL A model aircraft is a non human carrying aircraft capable of sustained flight in the atmosphere It may not exceed limita tions of this code and is intended exclusively for sport recre ation and or competition All model flights must be conducted in accordance with this safety code and any additional rules specific to the flying site 1 Model aircraft will not be flown a In a careless or reckless manner b At a location where model aircraft activities are prohibited 2 Model aircraft pilots will a Yield the right of way to all man carrying aircraft b See and avoid all aircraft and a spotter must be used when appropriate AMA Document 540 D See and Avoid Guidance c Not fly higher than approximately 400 feet above ground level within three 3 miles of an airport without notifying the airport operator d Not interfere with operations and traffic patterns at any airport heliport or seaplane base except where there is a mixed use agreement e Not exceed a takeoff weight including fuel of 55 pounds unless in compliance with the AMA Large Model Aircraft program AMA Document 520 A f Ensure the aircraft is identified with the
49. er your questions and service you in the event that you may need any assistance For questions or assistance please visit our website at www horizonhobby com submit a Product Support Inquiry or call 877 504 0233 toll free to speak to a Product Support representative Inspection or Services If this Product needs to be inspected or serviced and is compli ant in the country you live and use the Product in please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http www horizonhobby com content service center render service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service When calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the
50. ezione riparare o sostituire qualsiasi prodotto con siderato difettoso e che rientra nei termini di garanzia queste sono le uniche rivalse a cui l acquirente si pu appellare se un prodotto difettoso Horizon si riserva il diritto di controllare qualsiasi componente utilizzato che viene coinvolto nella rivalsa di garanzia Le deci sioni relative alla sostituzione o alla riparazione avvengono solo in base alla discrezione di Horizon Questa garanzia non copre dei danni superficiali o danni per cause di forza maggiore uso errato del prodotto negligenza uso ai fini commerciali o una qualsiasi modifica a qualsiasi parte del prodotto Questa garanzia non copre danni dovuti ad una installazione errata ad un funzionamento errato ad una manutenzione o un tentativo di riparazione non idonei a cura di soggetti diversi da Horizon La restituzione del prodotto a cura dell acquirente o da un suo rappresentante deve essere approvata per iscritto dalla Horizon Limiti di danno Horizon non si riterr responsabile per danni speciali diretti indiretti o consequenziali perdita di profitto o di produzione perdita commerciale connessa al prodotto indipendentemente dal fatto che la richiesta si basa su un contratto o sulla garanzia Inoltre la responsabilit di Horizon non supera mai in nessun caso il prezzo di acquisto del prodotto per il quale si chiede la responsabilit Horizon non ha alcun controllo sul montaggio sull utilizzo o sulla man
51. ge where canopy sits and open up the tab locations using a glue using damp cloth hobby knife 81 CANOPY INSTALLATION L119 L120 L121 Install the canopy on the fuselage and wait 24 hours for the glue to fully Remove the masking tape and check the canopy for any excessive gap Fill the gaps with canopy glue and use the magnets to hold in place cure 82 CANOPY INSTALLATION 122 Apply generous amount of petroleum jelly to the masking tape and spread it Apply a bead of clear silicone to the canopy frame including front and back Bolt the canopy to the fuselage Clean excess silicone that oozes out and over thoroughly of the canopy wait 24 hours for the silicone to fully cure 83 APPLYING CANOPY TRIM L11 I gt D A Ki LL gt 4 EK Ces b 7 Ons J a DI VE a Ld i fe VE gt Refer to the drawing for the measurement and location of the trims Dry fit Apply commercially available sticker solution to be able to make adjustments Mount the front and aft trims Work any bubble out the vinyl strip over the canopy and cut if needed 84 FUSELAGE CUTOUT FOR WING EXTENSIONS LIL11 Mark the aileron extension wire location It s about 2 inch forward of the aft Using a drill and 1 8 inch drill bit make a pilot hole in the fuselage anti rotation pin location on the fuselage Using a sa
52. h time you start your aircraft If any critical switches are on without your knowledge the transmitter alarm will sound a warn ing Check that all trim levers are in the proper location All servo pigtails and switch harness plugs should be secured in the receiver Make sure the switch har ness moves freely in both directions T GLICHER FLUG CHECK berpr fen Sie die Spannung des Senderakkus Flie gen Sie nicht wenn die Spannung unterhalb der vom Hersteller empfohlenen Spannung liegt da dieses zu einem Absturz f hren k nnte Achten Sie bei dem Test darauf dass die Polaritat auf dem Voltmeter richtig angezeigt wird berpr fen Sie alle montierten Teile Verbindungen Schrauben Muttern und Bolzen vor jedem Flug Stellen Sie sicher dass nichts blockiert und alle Teile vern nftig gesichert sind Stellen Sie sicher dass sich alle Ruder in die richtige Richtung bewegen F hren Sie einen Reichweitentest vor jeder Flugses Sion durch Schalten Sie dem Starten des Modells den Sender Aus und wieder Ein Machen Sie das vor jedem Starten Sollten sich kritische Schalter auf EIN Posi tion ohne ihr Wissen befinden wird der Sender Alarm geben Pr fen Sie ob alle Trimmschieber in der richtigen Position sind Alle Servokabel und Schalter sollten im Empf nger gesichert sein Stellen Sie sicher dass der Ein Aus Schalter sich ungehindert in beide Richtungen bewe gen kann CONTR LES SYST MATIQUES Contr lez la ten
53. heir waste equipment by handing it over to a desig nated collections point for the recycling of Mg waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environ ment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product Anweisungen zur Entsorgung von Elektro und Elektronik Altgeraten f r Benutzer in der Europ ischen Union Dieses Produkt darf nicht zusammen mit anderem Abfall entsorgt werden Stattdes sen ist der Benutzer daf r verantwortlich unbrauchbare Ger te durch Abgabe bei einer speziellen Sammelstelle f r das Eee Recycling von unbrauchbaren elektrischen und elektronischen Ger ten zu entsorgen Die separate Sammlung und das Recycling von unbr auchbaren Ger ten zum Zeitpunkt der Entsorgung hilft nat rliche Ressourcen zu bewahren und sicherzustellen dass Ger te auf eine Weise wiederverwertet werden bei der die menschliche Gesundheit und die Umwelt gesch tzt werden Weitere Informationen dazu wo Sie unbrauchbare Ger te zum Recycling abgeben k nnen erhalten Sie bei lokalen Amtern bei der M llabfuhr f r ee sowie dort wo Sie das Produkt gekauft aben Instructions relatives
54. hinzuweisen HINWEIS Wenn diese Verfahren nicht korrekt befolgt werden k nnen sich m glicherweise Sachsch den UND geringe oder keine Gefahr von Verletzungen ergeben ACHTUNG Wenn diese Verfahren nicht korrekt befolgt werden ergeben sich wahrscheinlich Sachsch den UND die Gefahr von schweren Verletzungen WARNUNG Wenn diese Verfahren nicht korrekt befolgt werden ergeben sich wahrscheinlich Sachsch den Kollateralschaden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit ober flachliche Verletzungen Nicht geeignet f r Kinder unter 14 Jahren Dies ist kein Spielzeug A WARNUNG Lesen Sie die GESAMTE Bedienungsanleitung um sich vor dem Betrieb mit den Produktfunktionen vertraut zu machen Wird das Produkt nicht korrekt betrieben kann dies zu Schaden am Produkt oder pers nlichem Eigentum f hren oder schwere Verletzungen verursachen Dies ist ein hochentwickeltes Hobby Produkt Es muss mit Vorsicht und gesundem Menschenverstand betrieben werden und ben tigt gewisse mechanische Grundfahigkeiten Wird dieses Produkt nicht auf eine sichere und verantwortungsvolle Weise betrieben kann dies zu Verletzungen oder Schaden am Produkt oder anderen Sachwerten f hren Dieses Produkt eignet sich nicht f r die Verwendung durch Kinder ohne direkte berwachung eines Erwachsenen Versuchen Sie nicht ohne Genehmigung durch Horizon Hobby Inc das Produkt zu zerlegen es mit inkompatiblen Komponenten zu verwenden oder auf jegliche Weise
55. i a pagamento Se bisogna effettuare una riparazione a pagamento effet tueremo un preventivo che verr inoltrato al vostro rivenditore La riparazione verr effettuata dopo l autorizzazione da parte del vostro rivenditore La somma per la riparazione dovr essere pagata al vostro rivenditore Le riparazioni a pagamento avranno un costo minimo di 30 minuti di lavoro e in fattura includeranno le spese di restituzione Qualsiasi riparazione non pagata e non richiesta entro 90 giorni verr considerata abbandonata e verr gestita di conseguenza Attenzione Le riparazioni a pagamento sono disponibili solo sull elettronica e sui motori Le riparazioni a livello meccanico soprattutto per gli elicotteri e le vetture RC sono molto costose e devono essere effettuate autonomamente dall acquirente WARRANTY AND SERVICE CONTACT INFORMATION e GARANTIE UND SERVICE KONTAKTIN FORMATIONEN e COORDONNEES DE GARANTIE ET REPARATIONS e GARANZIA E ASSISTEN ZA INFORMAZIONI PER CONTATTI WARRANTY AND SERVICE CONTACT INFORMATION e KUNDENDIENSTINFORMATIONEN e INFORMATIONS DE CONTACT POUR LES PIECES e INFORMAZIONI PER IL SERVIZIO CLIENTI 877 504 0233 P 4105 Fieldstone Rd 800 338 4639 Horizon Service Center 4105 Fieldstone Rd Online Repair Request visit United States Sales Champaign Illinois 61822 USA sales horizonhobby com Electronics and engines Champaign Illinois 61822 USA 4 www horizonhobby co
56. ie dass der Originalkarton in der Regel nicht ausreicht um beim Versand nicht beschadigt zu werden Verwenden Sie einen Paketdienstleister mit einer Tracking Funktion und Versicherung da Horizon bis zur Annahme keine Verantwortung f r den Versand des Produktes bernimmt Bitte legen Sie dem Produkt einen Kaufbeleg bei sowie eine ausf hrliche Fehlerbeschreibung und eine Liste aller eingesendeten Einzelkomponenten Weiterhin ben tigen wir die vollst ndige Adresse eine Telefonnummer f r R ckfragen sowie eine Email Adresse Garantie und Reparaturen Garantieanfragen werden nur bearbeitet wenn ein Originalkaufbeleg von einem autorisierten Fachhandler beiliegt aus dem der Kaufer und das Kaufdatum hervorgeht Sollte sich ein Garantiefall bestatigen wird das Produkt repariert oder ersetzt Diese Entscheidung obliegt einzig Horizon Hobby Kostenpflichtige Reparaturen Liegt eine kostenpflichtige Reparatur vor erstellen wir einen Kostenvoranschlag den wir Ihrem H ndler bermitteln Die Reparatur wird erst vorgenommen wenn wir die Freigabe des H ndlers erhalten Der Preis f r die Reparatur ist bei Ihrem H ndler zu entrichten Bei kostenpflichtigen Reparaturen werden mindestens 30 Minuten Werkstattzeit und die R ckversandkosten in Rechnung gestellt Sollten wir nach 90 Tagen keine Einverst ndniserkl rung zur Reparatur vorliegen haben behalten wir uns vor das Produkt zu vernichten oder anderweitig zu verwerten Achtung Kostenpfli
57. ife for a tight contact at the corner Then brush some finishing epoxy for the cloth once more 20 L1L120 Once the fiberglass resin is cured using a hobby knife cut the excess fiberglass cloth L121 Make all four servo trays using the same method As it has been stated be sure to thoroughly scratch the surfaces and then clean with acetone These Steps are extremely important otherwise tray can break and cause flutter and loss of control of the model AILERON SERVO INSTALLATION AND HINGE LINE SEALING 0103 001 The aileron hinge line needs to be seal from the bottom Deflect the aileron Use clear packing tape that is 1 1 2 inch to 2 inch wide Cut pieces as long Patiently and carefully complete the length of the aileron on both wings fully and clean the bevels using alcohol swab as the length between each two hinge Fold the tape and carefully apply to the hinge line Packing tapes are strong if removing the tape is necessary do so very carefully as not to take the paint off the surface 21 AILERON SERVO INSTALLATION HINGE LINE SEALING LILIA Prepare the servo by installing the rubber grommets and brass eye lets Run the servo mounting screws in and out of the tray and apply thin CA to Once CA is dry mount the servo such that the output shaft is closer to the holes aileron hinge line 22 AILER
58. included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton NOTICE Do not ship LiPo batteries to Horizon If you have any issue with a LiPo battery please contact the appropriate Horizon Product Support office Warranty Requirements For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon Non Warranty Service Should your service not be covered by warranty service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for service you are agreeing to payment of the service without notification Service estimates are available upon request You must include this request with your item submitted for service Non warranty service estimates will be billed a minimum of Y2 hour of labor In addition you will be billed for return freight Horizon accepts money orders and cashier s checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for service you are agreeing to Horizon
59. instructions fournies avec votre radio Charger votre radio la nuit qui pr c de la session de vol Chargez la batterie de l metteur et du r cepteur uniquement l aide du chargeur fourni ou recom mand par le fabricant de votre radio Suivez toutes les instructions des fabricants de vos composants lectroniques Contr lez votre installation radio et que toutes les gouvernes ailerons profondeur d rive et gaz fonctionnent dans la bonne direction et avec les bons d battements Contr lez tous les accessoires guignols palonniers et chapes pour tre s r qu ils sont en bon tat Avant chaque session de vol et surtout avec un nouveau modele effectuez un test de port e radio Consultez le manuel de votre radio pour les instruc tions pour effectuer un test de port e Faites tourner le moteur avec le mod le attach au sol et r p tez un essai de port e radio La port e ne doit pas tre affect e de mani re significa tive Si c est le cas ne tentez pas de voler Retirez l quipement radio et renvoyez le chez le fabricant pour une inspection CONTROLLI PRIMA DEL VOLO Caricare le batterie di trasmettitore ricevitore e ac censione motore usando i caricabatterie consigliati o forniti con il radiocomando e seguendo le istruzioni Caricare il radiocomando la notte prima di ogni ses sione di volo Seguire le istruzioni e le raccomandazi oni fornite insieme alle apparecchiature elettroniche Controllare l inst
60. ith T Coupler Tankstutzen mit T Kupplung Embout de remplissage pour le carburant dot d un Bocchettone carburante con giunto a T raccord en T TT 4502 B M 3W 4 1 2 P 51 Aluminum Tru Turn Spinner P 51 Tru Turn Aluminium Spinner C ne d h lice Tru Turn P 51 en aluminium 11 cm Spinner Tru Turn in alluminio da 114 3 mm SPM8800 OPTIONAL ITEMS e OPTIONALE TEILE e ELEMENTS OPTIONNELS ARTICOLI OPZIONALI Spektrum DX8 Spektrum DX8 Spektrum DX8 Spektrum DX8 Part English Deutsch Francais Italiano HAN362 Pilot HAN520025 Side Force Generator 10 REQUIRED TOOLS BEN TIGTES WERKZEUG e OUTILS REQUIS ATTREZZI NECESSARI English Deutsch Francais Italiano Rotary tool Drehbohrer Perceuse de pr cision Trapano Ruler Lineal Regle Righello Acetone Crimping tool Crimpzange Pince a sertir Utensile per crimpatura Cuttoff wheel Trennscheibe Disque de d coupe Troncatrice Denatured alcohol Spiritus Alcool d natur Alcool denaturato Dental floss Zahnseide Ficelle type fil dentaire Filo interdentale Commercial Solution for Applying Stickers L sungsmittel f r Aufkleber Spray humidificateur pour apposer des autocollants disponible dans le commerce Soluzione commerciale per l applicazione degli adesivi Drill bit 1 16 inch 1 8 inch 5 32 inch 3 16 inch 1 4 inch Bohrer 1 16 Zoll 3 16 Zoll For ts 1 6 mm 4 8 mm Punta del trapano 1 6 mm 4 8 mm Ep
61. l limination des D3E pour les utilisateurs r sidant dans l Union Europ enne Ce produit ne doit pas tre limin avec d autres d chets Il est de la responsabilit de l utilisateur d liminer les quipements rebut s en les remettant un point de collecte d sign en vue du recyclage des ENENENNE d chets d quipements lectriques et lectroniques La collecte et le recyclage s par s de vos quipements usag s au moment de leur mise au rebut aideront pr server les ressources naturelles et assurer le recyclage des d chets de mani re prot ger la sant humaine et l environnement Pour plus d informations sur les points de collecte de vos quipements usag s en vue du recyclage veuillez contacter votre mairie votre service de collecte des ordures m nag res ou le magasin dans lequel vous avez achet le produit Istruzioni per lo smaltimento di RAEE da parte di utenti dell Unione Europea Questo prodotto non deve essere smaltito assieme ai rifiuti domestici E responsabil it dell utente lo smaltimento di tali rifiuti che devono essere portati in un centro di raccolta predisposto per il riciclag Bs io di rifiuti elettrici e apparecchiature elettroniche La raccolta differenziata e il riciclaggio di tali rifiuti provenienti da apparecchiature nel momento dello smaltimento aiuteranno a preservare le risorse naturali e garantiranno un riciclaggio adatto a proteggere il benessere dell uomo e dell ambiente P
62. l appareil pour le vol consiste quilibrer parfaitement le mod le 1 Fixez les panneaux des ailes au fuselage Assurez vous de raccorder les fils de l aileron aux c bles appropri s du r cepteur Assurez vous qu aucun fil ne ressort du fuselage avant de serrer les vis des ailes Votre mod le doit tre bien assembl et pr t voler avant de l quilibrer 2 3 Assurez vous que votre modele est bien assembl et pr t voler lorsque vous l quilibrez Maintenez l avion en position verticale au niveau des marques effec tu es Vous pouvez soutenir les ailes avec vos doigts ou utiliser un support d quilibrage que vous trouverez dans le commerce Il s agit du point d quilibre correct pour votre modele 4 Le centre de gravit doit tre tr s proche des composants install s tel qu illustr dans le pr sent manuel Si le nez de votre appareil penche vers le bas d placez les batteries vers l arri re de l appareil Si la queue penche vers le bas ajoutez du poids vers le nez de l appareil Des plombs autocollants r f rence HAN3626 sont disponibles dans votre boutique de maquettes et mod lisme Ils peuvent vous aider quilibrer finement votre appareil AN ATTENTION Vous devez r gler le centre de gravit de votre mod le et l quilibrer de mani re satisfaisante avant d essayer de le faire voler CENTRO DI GRAVITA BARICENTRO Una parte importante nella preparazione di un aereo per il volo costit
63. l driver MatchBox so that there is no binding throughout the travel of the aileron 26 LANDING GEAR amp WHEEL PANTS INSTALLATION e e e o 001 002 Mate the landing gear with the appropriate wheel pant and mark the wheel Drill the marked location by using a 1 8 inch drill bit followed by a 5 32 inch Install the blind nut by tightening the M3x10mm screw provided using a pant set screw location drill bit 2 5mm ball driver 27 LANDING GEAR amp WHEEL PANTS INSTALLATION e e e o LILI6 a04 Using a drill and 1 4 inch drill bit enlarge the wheel axle hole On one side of the wheel install the 5mm bolt and a washer through the On the other side of the wheel install 6 washers and the locknut wheel 28 LANDING GEAR amp WHEEL PANTS INSTALLATION e e e o 007 0108 BIS oo Hold the locknut with a 10 wrench and using a 4 5mm hex tip run the bolt Slightly open up the wheel pant and insert the wheel in the wheel pant Pass the bolt through the wheel pant the landing gear leg and a washer and through the locknut Tighten enough to allow for the wheel to rotate with little then locknut Using a vise grip hold the head of the bolt and with the help of friction a 10 socket wrench tighten the locknut 29 LANDING GEAR amp WHEEL PANTS INSTALLATION e e e o
64. l guidelines measured from our own flight tests You can experiment with higher rates to match your preferred style of flying Travel Adjust and Sub Trims are not listed and should be adjusted according to each individual model and prefer ence Always install the control horns 90 degrees to the servo center line Use sub trim as a last resort to center the servos We highly recommend re binding the radio system once all the control throws are set This will keep the servos from moving to their endpoints until the transmitter and receiver connect Seitenruder Rechts Links 27 deg expo 35 27 deg expo 35 Die hier genannten Ruderausschl ge sind generelle Rich twerte die wir in unseren Testfl gen erflogen haben Sie k nnen mit gr Beren Ausschlagen experimentieren wenn diese mehr zu ihrem Flugstil passen Travel Adjust und Sub Trimm Werte sind hier nicht gelistet und sollten individuell nach Modell und Vorliebe eingestellt werden Montieren Sie die Servoh rner immer 90 zur Servomitte Nutzen Sie die Subtrimmfunktion als letzte M glichkeit die Servos zu zentrieren Wir empfehlen dringend nach Einstellung aller Rude rausschlage das System neu zu binden Das halt die Servos davon ab in die Endausschlage zu laufen solange der Sender und Empf nger noch nicht verbunden sind Haut 19 deg expo 25 26 deg expo 30 Bas 11 5 deg expo 25 16 5 deg exp 30 Profondeur PETITS GRANDS Haut 15 deg expo 40 35
65. m service United States 7 EON Units 1 4 Ployters Rd 44 0 1279 641 097 Horizon Product Support 4105 Fieldstone Rd 877 504 0233 United Kingdom Horizon Hobby Limited Staple Tye sales horizonhobby co uk All other products Champaign Illinois 61822 USA productsupport horizonhobby com Harlow Essex CM18 7NS United Kingdom y c0 Units 1 4 Ployters Rd Christian Junge StraBe 1 49 4121 46199 60 United Kingdom Horizon Hobby Limited Staple Tye 44 0 1279 641 097 Germany Horizon Hobby GmbH 25337 Elmshorn Germany service horizonhobby de H sales horizonhobby co uk arlow Essex CM18 7NS United Kingdom France Horizon Hobby SAS 11 Rue Georges Charpak 33 0 1 60 18 34 90 Christian Junge StraBe 1 49 0 4121 2655 100 y 77127 Lieusaint France infofrance horizonhobby com Germany Horizon Technischer Service 25337 El f mshorn Germany service horizonhobby de China Horizon Hobby China Room 506 No 97 Changshou Rd 86 021 5180 9868 11 Rue Georges Charpak 33 0 1 60 18 34 90 i Shanghai China 200060 info horizonhobby com cn France Horizon Hobby SAS 77127 Lieusaint France infofrance horizonhobby com China Horizon Hobby China Room 506 No 97 Changshou Rd 86 021 5180 9868 Shanghai China 200060 info horizonhobby com cn Instructions for disposal of WEEE by users in the European Union This product must not be disposed of with other waste Instead it is the user s responsibility to dispose of t
66. n tuteur La notice d utilisation contient des indications relatives la s curit ainsi que des indications concernant la maintenance et le fonctionnement du produit Il est absolument indispensable de lire et de comprendre ces indications avant la premi re mise en service C est uniquement ainsi qu il sera possible d viter une manipulation erron e et des accidents entrainant des blessures et des d gats Questions assistance et r parations Votre revendeur sp cialis local et le point de vente ne peuvent effectuer une estimation d ligibilit l application de la garantie sans avoir consult Horizon Cela vaut galement pour les r parations sous garantie Vous voudrez bien dans un tel cas contacter le revendeur qui conviendra avec Horizon d une d cision appropri e destin e vous aider le plus rapidement possible Maintenance et r paration Si votre produit doit faire l objet d une maintenance ou d une r paration adressez vous soit votre revendeur sp cialis soit directement Horizon Emballez le produit soigneusement Veuillez noter que le carton d emballage d origine ne suffit pas en r gle g n rale prot ger le produit des d g ts pouvant survenir pendant le transport Faites appel un service de messagerie proposant une fonction de suivi et une assurance puisque Horizon ne prend aucune responsabilit pour l exp dition du produit jusqu sa r ception accept e Veuillez joindre une preuve d
67. nding drum with 3 8 inch diameter enlarge the hole 85 OPTIONAL SIDE FORCE GENERATOR INSTALLATION LIL11 L1L12 LILI3 Css Temporarily hold the side force generator in place so that it is in the groove Using a felt pen mark the mounting hole locations onto the wing tip Using a 1 16 inch drill bit and high speed drill or rotary tool make pilot holes and squared M It is very important to use a high speed rotary tool and increase the drill bit size with 1 16 inch at a time to finally get to 1 4 inch drill bit 86 OPTIONAL SIDE FORCE GENERATOR INSTALLATION Mix 15 minute epoxy and micro balloons Fill the holes with glue Install the inserts using a flat blade screw driver until it is flush with the wing tip Wipe excess glue using alcohol swab and ensure no glue gets inside the insert Install the side force generator using screws and washers provided 87 STICKER INSTALLATION L11 The picture above shows the location of QQ Yak sticker on the fuselage The picture above shows the stickers that go on the cowl and fuselage The picture above shows the sticker that goes on the rudder 88 STICKER INSTALLATION 14 The picture above shows the stickers that go on left and right wing panel CONTROL SURFACE MEASUREMENT Control surface deflections are measured as picture
68. ne mounting tabs 45 ENGINE DOME PREPARATION FOR DA 120 e e o Using a drill and 1 16 inch drill bit make a pilot hole Then use 1 8 inch Insert blind nuts and using a 4 5mm ball driver along with the 1 inch standoff Mark the top of the engine dome for ignition module and ignition battery 14 inch and 5 16 inch drill bits respectively and enlarge the hole needed for the engine installation pull the blind nuts in the engine dome installation by tracing the outside of the ignition box and battery 46 ENGINE DOME PREPARATION FOR DA 120 e e o L17 Using a rotary tool and a cutting disk and cut the marked location just a little Drill a 3 8 inch diameter hole for ignition wires Start from smaller bits and Install a rubber grommet with ID of 3 8 inch longer than the hook and loop strap width increase one size at a time 47 IGNITION MODULE AND BATTERY INSTALLATION e e o L11 Apply masking tape to the back of ignition module then apply a servo tape Apply masking tape to the back of the ignition battery then apply two strips of Remove the backing of the servo tape and mount both the ignition and the strip to the masking tape servo tape to the masking tape battery Use a piece of hook and loop and secure them 48 THROTTLE SERVO INSTALLATION e e e L11 Prepare the servo tray pieces for assembly and dry fit the pieces
69. nza o riparazione senza aver prima consultato Horizon questo vale anche per le riparazioni in garanzia Quindi in tali casi bisogna interpellare un rivenditore che si metter in contatto subito con Horizon per prendere una decisione che vi possa aiutare nel pi breve tempo possibile Manutenzione e riparazione Se il prodotto deve essere ispezionato o riparato si prega di rivolgersi ad un rivenditore specializzato o direttamente ad Horizon il prodotto deve essere Imballato con cura Bisogna far notare che i box originali solitamente non sono adatti per effettuare una spedizione senza subire alcun danno Bisogna ef fettuare una spedizione via corriere che fornisce una tracciabilit e un assicurazione in quanto Horizon non si assume alcuna responsabilit in relazione alla spedizione del prodotto Inserire il prodotto in una busta assieme ad una descrizione dettagliata degli errori e ad una lista di tutti i singoli componenti spediti In oltre abbiasmo bisogno di un indirizzo completo di un numero di telefono per chiedere ulteriori domande e di un indirizzo e mail Garanzia e riparazione Le richieste in garanzia verranno elaborate solo se presente una prova d acquisto in originale proveniente da un rivenditore specializzato autorizzato nella quale ben visibile la data di ac quisto Se la garanzia viene confermata allora il prodotto verr riparato o sostituito Questa decisione spetta esclusivamente a Horizon Hobby Riparazion
70. o Vicino ad ogni passo sono stati posti dei piccoli quadrati L1 per aiutare a tenere traccia delle cose fatte e di quelle da fare passi con un singolo quadrato L1 vengono eseguiti una sola volta mentre quelli con quadrati multipli CC si devono ripetere come nel caso dell ala destra e sinistra due servi ecc Ricordatevi di non aver fretta e di seguire fedelmente le istruzioni SAFETY WARNINGS AND PRECAUTIONS Read and follow all instructions and safety precautions before use Improper use can result in fire serious injury and damage to property Components Use only with compatible components Should any compatibility questions exist please refer to the product instructions component instructions or contact the ap propriate Horizon Hobby office Flight Fly only in open areas to ensure safety It is recommend ed flying be done at AMA Academy of Model Aeronautics approved flying sites Consult local ordinances before choosing a flying location Propeller Keep loose items that can become entangled in the propeller away from the prop This includes loose clothing or other objects such as pencils and screwdrivers Keep your hands away from the propeller as injury can occur Batteries Always follow the manufacturers instructions when using and disposing of any batteries Mishandling of Li Po bat teris can result in fire causing serios injury and damage Small Parts This kit includes small parts and should no
71. of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification of or to any part of the Product iv attempted service by anyone other than a Hori zon Hobby authorized service center v Product not purchased from an authorized Horizon dealer or vi Product not compliant with applicable technical regulations OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER S INTENDED USE Purchaser s Remedy Horizon s sole obligation and purchaser s sole and exclusive remedy shall be that Horizon will at its option either i service or ii replace any Product determined by Horizon to be defec tive Horizon reserves the right to inspect any and all Product s involved in a warranty claim Service or replacement deci sions are at the sole discretion of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER S SOLE AND EXCLUSIVE REMEDY Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCI DENTAL OR CONSEQUENTIAL DAM
72. offen das Sie an der Super Decathlon so viel Freude wie wir haben G N RALIT S CONCERNANT LE VOL Le Super Decathlon est un appareil tr s docile en l air comme au sol Les atterrissages et les d collages sont tr s faciles et lents Commencez par poser le mod le au sol Contr lez que toutes les gouvernes fonctionnent dans la bonne direc tion Montez votre trim des gaz pour obtenir un ralenti soutenu Roulez au sol face au vent Augmentez les gaz progressivement en compensant la d rive La queue doit se lever rapidement Une fois que vous tes plein gaz et que vous avez pris de la vitesse tirez l g rement sur la profondeur et le Super Decathlon va quitter le sol tranquillement et prendre de l altitude Une fois que l avion commence prendre de l altitude rel chez la profondeur et continuez de grimper tranquillement jusqu environ une altitude de 30m environ Une fois que vous tes 30m d altitude trimez le mod le de facon a voler plat avec 5 8 des gaz Vous trouverez que le Super Decathlon est un avion tr s doux et qu il semble tr s l ger aux manches Ce mod le est capable d effectuer des manoeuvre de voltige basiques boucles tonneaux vol tranche vol dos ect Nous esp rons que vous prendrez autant de plaisir avec votre Super Decathlon Hangar 9 que nous GENERALITA SUL VOLO Il Super Decathlon un modello molto docile sia in aria che a terra decolli sono facili e gli atterraggi lenti e dol
73. ons unless a The aircraft control system and pilot skills have success fully demonstrated all maneuvers intended or anticipated prior to the specific event b An inexperienced pilot is assisted by an experienced pilot When and where required by rule helmets must be properly worn and fastened They must be OSHA DOT ANSI SNELL or NOCSAE approved or comply with comparable standards B RADIO CONTROL RC 1 All pilots shall avoid flying directly over unprotected people vessels vehicles or structures and shall avoid endangerment of life and property of others Asuccessful radio equipment ground range check in ac cordance with manufacturer s recommendations will be completed before the first flight of a new or repaired model aircraft At all flying sites a safety line s must be established in front of which all flying takes place AMA Document 706 Recom 9 mended Field Layout a Only personnel associated with flying the model aircraft are allowed at or in front of the safety line b At air shows or demonstrations a straight safety line must be established c An area away from the safety line must be maintained for spectators d Intentional flying behind the safety line is prohibited RC model aircraft must use the radio control frequencies currently allowed by the Federal Communications Commis sion FCC Only individuals properly licensed by the FCC are authorized to operate equipm
74. ontrol throws are set This will keep the servos from moving to their endpoints until the transmitter and receiver connect ATTENTION Rebind the radio system once all control throws are set This will keep the servos from moving to their endpoints until the transmitter and receiver connect 12 VOR DEM ZUSAMMENBAU e Entnehmen Sie zur berpr fung jedes Teil der Ver packung e berpr fen Sie den Rumpf Tragfl chen Seiten und H henruder auf Besch digung e Sollten Sie besch digte oder fehlende Teile feststellen kontaktieren Sie bitte den Verkaufer Zum Entfernen von Falten in der Bespannung verwenden Sie den Hei luftf n HAN100 und Bespannhandschuh HAN150 oder das Folienb geleisen HAN141 Bitte achten Sie bei berlappenden Farben dass Sie diese sich bei dem Bearbeitung nicht trennen Laden des Senders und Empf ngers e Zentrieren der Trimmungen und Sticks auf dem Sender e Sollten Sie einen Computersender verwenden resetten Sie einen Speicherplatz und benennen ihn nach dem Modell e Sender und Empfanger jetzt nach den Bindeanweisung des Herstellers zu binden e Wir empfehlen dringend nach Einstellung aller Ruderausschl ge das System neu zu binden Das h lt die Servos davon ab in die Endausschl ge zu laufen solange der Sender und Empf nger noch nicht verbunden sind WICHTIG Wir empfehlen dringend nachdem alle Einstellungen vorgenommen worden sind das Modell neu zu binden Dieses verhinde
75. or 16 AILERON SERVO TRAY INSTALLATION e 0013 0014 Dry fit the other two pieces carefully then using Mercury 100XF CA and glue Cut the fiber glass strip provided to six pieces Above pictures show how these fiberglass pieces will be glued using finishing pieces 2 and 3 one at a time Hold each piece under pressure until CA dries epoxy resin to strengthen the tray 17 AILERON SERVO TRAY INSTALLATION e 0016 0017 0018 Mix finishing epoxy resin and brush it on the tray bracket then lay the fiber Using a brush apply some resin on top of the cloth Use the back of a hobby knife and push the fiberglass cloth in the corners to glass cloth and let it get wet Work the fiberglass cloth for a tight fit make sure cloth adheres properly with no gap or bubble to the servo tray sup port Following the same method do the right side of the servo tray support 18 AILERON SERVO TRAY INSTALLATION e 0019 11120 0021 f E Se ud Following the same method fiberglass the servo tray piece to the tray bracket Thoroughly scuff the tray and the hatch for this step as it is a very important Use acetone and clean the hatch part of this process 19 AILERON SERVO TRAY INSTALLATION e L1L122 o Apply finishing epoxy and lay the fiberglass Work the fiberglass cloth with the back of a hobby kn
76. orbereitung der Verkleidung und Einbau des Schalld mpfers esses 59 Einbau des Fl gelservos und der Querruderscharniere s sssssnnsanneianeieeeneeeennae 63 Einbau der Fl gelstreben 71 Verkabelung und Befestigung des H henleitwerks seeen 75 Einbau von Armaturenbrett und Instrumententaigl in 78 Einbau der Fenster und der Windschutzscheibe 80 Zusammen und Einbau der Sitze 82 Einbau der Fl gelsptizenumrandung und Anbringen der Aufkleber s ssssssssnesieneeesnenene Einbau der T r vor dem Flug Schwerpunkt Ruderausschlag Checkliste vor dem Flug T gliche Flug Checkliste Allgemeine Hinweise zum Fliegen ELE Garantie und Servicekontaktinformationen 91 TABLE DES MATI RES El ments d assemblage sss Sch ma de montage Caract ristiques 8 Contenu du kit et liste des pi ce Pi ces de rechange Articles n cessaires Articles optionnels re Outils n cessaires Avant de d buter le montage Montage Assemblage du train d atterrissage et des entretoises des haubanS 13 Assemblage de la charni re de la gouverne de direction et du guignol de commande 17 Assemblage des servos des gouvernes de profondeur du guignol de commande et des stabilis
77. oxy brushes Epoxidharzpinsel Pinceaux poxy Pennelli per espossidica Felt tipped pen Filzstift Crayon feutre Pennarello Flat file Flachfeile Lime plate Lima piatta Ball driver 1 16 inch 3 32 inch 3 16 inch 7 64 inch 1 5mm 4mm 4 5mm Kugelkopfschraubendreher 1 16 Zoll 3 32 Zoll 3 16 Zoll 1 64 Zoll 1 5 mm 4 mm 4 5 mm Tournevis Allen 1 6 mm 2 4 mm 4 8 mm 2 8 mm Cacciavite con testa a sfera 1 6 mm 2 4 mm 4 8 mm 2 8 mm 1 5 mm 4 mm 4 5 mm Sanding drum Trommelschleifmaschine Embout de poncage cylindrique Punta per scartavetratura Hobby knife 11 blade Hobbymesser mit Schneide Nr 11 Couteau de mod lisme dot d une lame n 11 Taglierino lama n 11 Hobby scissors Hobbyschere Ciseaux de mod lisme Forbici per modellismo Hook and loop strap and tape Klettriemen und Klettband Attaches auto agrippantes et ruban adh sif Fascette e nastro a strappo Tie Wraps Kabelbinder Colliers nylon Fascette Double Sided Tape Doppelseitiges Klebeband Ruban adh sif double face Nastro biadesivo Medium grit sandpaper Schleifpapier mittelk rnig Papier de verre de grain moyen Carta vetrata a grana media Mixing cups and sticks Mischbecher und R hrst be Assortiment de gobelets et touillettes Bicchieri e bastoncini di miscelazione Needle nose pliers Spitzzange Pinces long bec Pinze con becchi ad ago Pin vise Feilkolben Porte foret Porta
78. punte Open end wrench 1 4 inch 13mm Gabelschl ssel Zoll 13 mm Cl s plates 6 mm 13 mm Chiave fissa 6 mm 13 mm Paper towels Papierhandtuch Essuie tout Carta asciugatutto Pencil Bleistift Crayon papier Matita Phillips screwdriver 1 2 Kreuzschlitzschraubenzieher 1 2 Tournevis cruciforme 1 2 Cacciavite con testa a croce 1 2 Pin vise Feilkolben Micro perceuse manuelle Portapunte Crescent wrench Englander Schraubenschl ssel Cl a molette Chiave regolabile Flat tip screwdriver Schlitzschraubendreher Tournevis a bout plat Cacciavite a punta piatta Petroleum Jelly Vaseline Vaseline Vaselina 11 BEFORE STARTING ASSEMBLY Remove parts from bag nspect fuselage wing panels rudder and stabilizer for damage f you find damaged or missing parts contact your place of purchase If you find any wrinkles in the covering use a heat gun HAN100 and covering glove HAN150 or covering iron HAN101 with a sealing iron sock HAN141 to remove them Use caution while working around areas where the colors overlap to prevent separating the colors Charge transmitter and receiver batteries Center trims and sticks on your transmitter For a computer radio create a model memory for this particular model Bind your transmitter and receiver using your radio system s instructions You must re bind the radio system once all the c
79. que de blessures ATTENTION Proc dures qui si elles ne sont pas suivies correctement peuvent entrainer des d gats mat riels ET des blessures graves AVERTISSEMENT Proc dures qui si elles ne sont pas suivies correctement peuvent entrainer des d gats mat riels et des blessures graves OU engendrer une probabilit lev e de blessure superficielle 14 ans et plus Ceci nest pas un jouet A AVERTISSEMENT Lisez la TOTALIT du manuel d utilisation afin de vous familiariser avec les caract ristiques du produit avant de le faire fonctionner Une utilisation incorrecte du produit peut entrainer sa d t rioration ainsi que des risques de d gats mat riels voire de blessures graves Ceci est un produit de loisirs sophistiqu Il doit tre manipul avec prudence et bon sens et requiert des aptitudes de base en m canique Toute utilisation irresponsable de ce produit ne respectant pas les principes de s curit peut provoquer des blessures entra ner des d g ts mat riels et endommager le produit Ce produit n est pas destin tre utilis par des enfants sans la surveillance directe d un adulte N essayez pas de d monter le produit de l utiliser avec des composants incompatibles ou d en am liorer les performances sans l accord d Horizon Hobby Inc Ce manuel comporte des instructions relatives la s curit au fonctionnement et l entretien Il est capital de lire et de respecter la totalit des instructions et avertiss
80. r the glue to dry arm 33 RUDDER SERVO AND PULL PULL CABLE INSTALLATION e EINBAU VON HOHENRUDERSERVO UND PULL PULL KABEL ASSEMBLAGE DU CABLE PULL PULL ET DU SERVO DE LA GOUVERNE DE DIRECTION e INSTALLAZIONE DEL SERVO DEL TIMONE E DEI CAVETTI DI COMANDO L11 Prepare the servo by inserting the rubber grommets and brass eyelets Install the ball link on the eye bolt Leave room for further adjustment Using a inch wrench and 3 32 inch ball driver install the ball link on the last straight hole on the servo arm 34 RUDDER SERVO AND PULL PULL CABLE INSTALLATION e EINBAU VON H HENRUDERSERVO UND PULL PULL KABEL e ASSEMBLAGE DU CABLE PULL PULL ET DU SERVO DE LA GOUVERNE DE DIRECTION e INSTALLAZIONE DEL SERVO DEL TIMONE E DEI CAVETTI DI COMANDO L16 VY NM Temporarily connect the servo to the receiver and power up the receiver Apply thread lock to the servo arm center screw Install the center screw and Cut the pull pull cable in half Install the arm perpendicular to the output shaft Use sub trim if necessary both set screws RUDDER SERVO AND PULL PULL CABLE INSTALLATION EINBAU VON HOHENRUDERSERVO UND PULL PULL KABEL ASSEMBLAGE DU CABLE PULL PULL ET DU SERVO DE LA GOUVERNE DE DIRECTION e INSTALLAZIONE DEL SERVO DEL TIMONE E DEI CAVETTI DI COMANDO
81. rt dass die Servos in die Endanschl ge laufen bevor sich Sender und Empfanger verbunden haben AVANT DE COMMENCER L ASSEMBLAGE Retirez toutes les pi ces des sachets pour les inspecter Inspectez soigneusement le fuselage les ailes et les empennages e Si un l ment est endommag contactez votre revendeur Si l entoilage pr sente quelques plis vous pouvez les lisser en utilisant le pistolet air chaud HAN100 et le gant HAN150 ou le fer entoiler HAN101 avec la chaussette de protection HAN141 Agissez soigneuse ment dans les zones ou plusieurs couleurs d entoilage sont superpos es afin d viter de les s parer est recommand de pr parer tous les l ments du syst me de la radio Cela inclut la charge des batteries comme la mise au neutre des trims et des manches de votre metteur Si vous utilisez une radio programmable s lectionnez une m moire libre afin d y enregistrer les param tres de ce mod le Nous vous recommandons d affecter maintenant le r cepteur l metteur en suivant les instructions fournies avec votre radio R affectez votre radio quand tous les r glages de d battements sont effectu s Cela emp chera les servos d aller en but e lors de la connexion de l metteur et du r cepteur ATTENTION Il est hautement recommand de r affect er le syst me une fois que les courses seront r gl es Cela emp chera les servos d aller en but e lors de
82. s Terms and Conditions found on our website http www horizonhobby com content service center render service center NOTICE Horizon service is limited to Product compliant in the country of use and ownership If non compliant product is received by Horizon for service it will be returned unser viced at the sole expense of the purchaser GARANTIE UND SERVICE INFORMATIONEN Warnung Ein ferngesteuertes Modell ist kein Spielzeug Es kann wenn es falsch eingesetzt wird zu erheblichen Verletzungen bei Lebewesen und Besch digungen an Sachg tern f hren Betreiben Sie Ihr RC Modell nur auf freien Pl tzen und beachten Sie alle Hinweise der Bedienungsanleitung des Modells wie auch der Fernsteuerung Garantiezeitraum Exklusive Garantie Horizon Hobby Inc Horizon garantiert dass das gekaufte Produkt frei von Material und Montagefehlern ist Der Garantiezeitraum entspricht den gesetzlichen Bestimmung des Landes in dem das Produkt erworben wurde In Deutschland betr gt der Garantiezeitraum 6 Monate und der Gew hrleistungszeitraum 18 Monate nach dem Garantiezeitraum Einschr nkungen der Garantie Einschr nkungen der Garantie a Die Garantie wird nur dem Erstkaufer Kaufer gewahrt und kann nicht bertragen werden Der Anspruch des Kaufers besteht in der Reparatur oder dem Tausch im Rahmen dieser Garantie Die Garantie erstreckt sich ausschlieBlich auf Produkte die bei einem autorisierten Horizon H ndler erworben wurden
83. s de quelque mani re que ce soit au produit et ce ind pendamment du fait qu un recours puisse tre formul en relation avec un contrat la garantie ou l obligation de garantie Par ailleurs Horizon n acceptera pas de recours issus d un cas de garantie lorsque ces recours d passent la valeur unitaire du produit Horizon n exerce aucune influence sur le montage l utilisation ou la maintenance du produit ou sur d ventuelles combinaisons de produits choisies par l acheteur Horizon ne prend en compte aucune garantie et n accepte aucun recours pour les blessures ou les dommages pouvant en r sulter En utilisant et en montant le produit l acheteur accepte sans restriction ni r serve toutes les dispositions relatives la garantie figurant dans le pr sent document Si vous n tes pas pr t en tant qu acheteur accepter ces dispositions en relation avec l utilisation du produit nous vous demandons de restituer au vendeur le produit complet non utilis et dans son emballage d origine Indications relatives la s curit Ceci est un produit de loisirs perfectionn et non un jouet Il doit tre utilis avec pr ATTENTION et bon sens et n cessite 96 quelques aptitudes m caniques ainsi que mentales L incapacit utiliser le produit de mani re sire et raisonnable peut provoquer des blessures et des d g ts mat riels cons quents Ce produit n est pas destin tre utilis par des enfants sans la surveillance par u
84. s for guidance and familiarize yourself with the current local rules and FAA regulations governing model aviation in your location More information about model aviation can be found at www modelaircraft org The Federal Aviation Administration can be found online at www faa gov 99 HANGAR 9 2012 Horizon Hobby Inc Hangar 9 Evolution JR DSM2 Side Force Generators PowerPro and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby Inc DSMX is a trademark of Horizon Hobby Inc registered in the U S The Spektrum trademark is used with permission of Bachmann Industries Inc Saito is a trademark of Saito Seisakusho Co Ltd Japan All other trademarks service marks and logos are the property of their respective owners XXXXXX Created 2 2013
85. s tension Con tr lez les mouvements de la d rive en utilisant votre metteur Quand le manche est vers la droite la d rive doit s orienter vers la droite Inversez la direction du servo l metteur si n cessaire 2 Contr lez les mouvements de la profondeur en utilisant votre metteur D placez le manche vers le bas la profondeur doit s orienter vers le haut 3 Contr lez les mouvements des ailerons en utilisant votre metteur D placez le manche vers la droite l aileron droit doit s orienter vers le haut et l aileron gauche doit s orienter vers le haut 4 CORSE DEI COMANDI 1 Accendere trasmettitore e ricevitore del modello Con trollare i movimenti del timone agendo sul trasmetti tore Quando lo stick va a destra anche il timone deve andare a destra Se questo non avvenisse bisogna invertire il verso del servo dal trasmettitore 2 Sempre con il radiocomando controllare il movimento dell elevatore Muovendo il suo stick verso il basso del trasmettitore l elevatore si deve muovere verso l alto 3 Provare ora il movimento degli alettoni spostando il relativo stick sul trasmettitore verso destra l alettone destro deve andare verso l alto e quello sinistro verso il basso Ailerons PETITS GRANDS Elevator LOW HIGH Up 15 mm expo 20 95 mm expo 40 Down 15 mm expo 20 95 mm expo 40 Rudder Right 50 mm expo 5 120 mm expo 45 Left 50 mm expo 5 120 mm expo 45 These are genera
86. sion de la batterie de l metteur Ne volez jamais en dessous de la tension minimale recommand e par le fabricant Le faire pourrait entrainer un crash Quand vous contr lez les batteries soyez certain de respecter les polarit s avec votre voltm tre Contr lez tous les accessoires guignols palonniers et chapes pour tre s r qu ils sont en bon tat V rifiez que toutes les gouvernes fonctionnent de mani re correcte Effectuez un test de port e avant chaque journ e de vol Avant de d marrer votre avion mettez votre metteur hors tension puis remettez le sous tension Faites cela avant chaque d marrage Si des interrupteurs ne sont pas dans des positions correctes l alarme de l metteur vous avertira Contr lez que tous les leviers de trims sont correcte ment plac s Tous les c bles de servos et c bles d interrupteur sortants du r cepteur doivent tre maintenus en place Contr lez que l interrupteur se d place libre ment dans les deux directions CONTROLLI PER OGNI SESSIONE DI VOLI Controllare la tensione della batteria del trasmet titore Non volare se la tensione inferiore a quella indicata dal costruttore in caso contrario si potrebbe avere un incidente distruttivo Quando si prova questa batteria accertarsi di avere la giusta polarit sul voltmetro a scala espansa Controllare tutti i rinvii le viti i dadi e i bulloni prima di ogni giornata di volo Verificare che non ci siano impe
87. t tre effectu es par l acheteur lui m me DURATA DELLA GARANZIA Periodo di garanzia Garanzia esclusiva Horizon Hobby Inc Horizon garantisce che i prodotti acquistati il Prodotto sono privi di difetti relativi ai materiali e di eventuali errori di montaggio II periodo di garanzia conforme alle disposizioni legali del paese nel quale il prodotto stato acquistato Tale periodo di garanzia ammonta a 6 mesi e si estende ad altri 18 mesi dopo tale termine Limiti della garanzia a La garanzia limitata all acquirente originale Acquirente e non cedibile a terzi L acquirente ha il diritto a far riparare o a far sostituire la merce durante il periodo di questa garanzia La garanzia copre solo quei prodotti acquistati presso un rivenditore autorizzato Horizon Altre transazioni di terze parti non sono coperte da questa garanzia La prova di acquisto necessaria per far valere il diritto di garanzia Inoltre Horizon si riserva il diritto di cambiare o modificare i termini di questa garanzia senza alcun preavviso e di escludere tutte le altre garanzie gi esistenti b Horizon non si assume alcuna garanzia per la disponibilit del prodotto per l adeguatezza o l idoneit del prodotto a parti colari previsti dall utente sola responsabilit dell acquirente il fatto di verificare se il prodotto adatto agli scopi da lui previsti c Richiesta dell acquirente spetta soltanto a Horizon a propria discr
88. t be left unat tended near children as choking and serious injury could result WARNUNGEN UND SICHERHEITS VORKEHRUNGEN Bitte lesen und befolgen Sie alle Anweisungen und Sichervorkehrungen vor dem Gebrauch Falscher nicht sachgem Ber Gebrauch kann Feuer ernsthafte Verletzun gen und Sachbeschadigungen zur Folge haben Komponenten Verwenden Sie mit dem Produkt nur kompatible Kompo nenten Sollten Fragen zur Kompatibilit t auftreten lesen Sie bitte die Produkt oder Bedienungsanweisung oder kontaktieren den Service von Horizon Hobby Fliegen Fliegen Sie um Sicherheit garantieren zu k nnen nur in weiten offenen Gegenden Wir empfehlen hier den Betrieb auf zugelassenen Modellflugpl tzen Bitte beachten Sie lokale Vorschriften und Gesetze bevor Sie einen Platz zum Fliegen wahlen Propeller Halten Sie lose Gegenstande die sich im Propeller verfangen k nnen weg vom Propeller Dieses gilt auch f r Kleidung oder andere Objekte wie zum Beispiel Stifte oder Schraubendreher Halten Sie ihre Hande weg vom Propeller es besteht akute Verletzungsgefahr Akkus Folgen Sie immer den Herstelleranweisungen bei dem Gebrauch oder Entsorgung von Akkus Falsche Behand lung von LiPo Akkus kann zu Feuer mit K rperverletzun gen und Sachbesch digung f hren Kleinteile Dieser Baukasten beinhaltet Kleinteile und darf nicht unbeobachtet in der N he von Kindern gelassen werden da die Teile verschluckt werden k nnten mit ernsth
89. t down as shown in the pictures above Using a rotary tool and a cutting disk cut the engine dome to accommodate for the header CANISTER INSTALLATION OPTION e e e Bottom of the fuselage right in front of the landing gear needs to be opened up to accommodate for canister exits The picture above shows the canisters mounted Fill line should be held on top and be away from the canisters Assemble the battery tray 71 CANISTER INSTALLATION OPTION e e L16 Using thin CA glue the mount Wait until CA is dry and repeat the process This Once the position of the battery is known glue the tray using epoxy and The picture above shows the tray with battery installed should be done for both sides of the battery tray mount Do not use accelera micro balloon Tray stands are cut such that to fit the round shape of the tor Use medium CA to fill any remaining gap fuselage for proper contact Make sure to glue the round part of the leg to the fuselage 72 RECEIVER INSTALLATION EINBAU DES EMPF NGERS e INSTALLATION DU R CEPTEU DU R CEPTEUR INSTALLAZIONE DEL RICEVITORE DI D2 Install multi layers of servo tape on top of each other where the receiver is to Glue a piece of hook and loop using medium CA Apply masking tape to the back of the receiver be installed RECEIVER INSTALLATION EINBAU DES EMPF NGERS INSTA
90. tabilizzatori 75 Installazione del cruscotto e del pannello LEI EE 78 Installazione dei finestrini e del parabrezza 80 Assemblaggio e installazione del sedile 82 Installazione smusso estremit alari e decals 93 Fissaggio porta di accesso a bordo 83 Centro di gravit sse 84 Escursione dei Comandt in 85 Controlli prima del volo es 86 Controlli per ogni sessione di voli Informazioni generali sul volo Garanzia limitata sse Garanzia e informazioni di contatto per l assistenza 91 pem 102 in 2 6 m eg 2000 sq in 130 sq dm D 28 29 Ib 12 7 13 2 kg 2 Stroke Gas 100 120cc 2 Takt Benzin Motor 100 120cc 2 temps essence 100 120cc 2 Tempi a benzina 100 120cc ur 8 channel or greater with 8 servos WY Bia 8 Kanal oder gr Ber mit 8 Servos 8 voies ou plus avec 8 servos 8 canali o pi con 8 servi 8 1 4 to 8 11 16 inch 210 to 220 mm REPLACEMENT PARTS ERSATZTEILE e PIECES DE RECHANGE RICAMBI Part English 1 HAN520001 Fuselage without Motor Dome QQ Yak 54 2 6m Comp Deutsch Francais Italiano HAN520002 Right Wing Panel QQ Yak 54 2 6m Comp HAN520003 Left Wing Panel QQ Yak 54 2 6m Comp HAN520004 Horizontal Stabilizer Set QQ Yak 54 2 6m Comp HAN520005 Rudder QQ Yak 54 2 6m Comp HAN520006 Landing Gear QQ Yak 54 2 6 m Comp H
91. this Product in a safe and responsible manner could re sult in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not attempt disassembly use with incompatible components or aug ment product in any way without the approval of Horizon Hobby Inc This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Using the Manual This manual is divided into sections to help make assembly easier to understand Boxes L1 have been placed next to each step These help keep track of steps that have been completed Steps with a single box L1 are performed once while steps with multiple boxes OO will require repeating For example right and left wing panels two servos etc Remember to take your time and follow the directions HINWEIS Alle Anweisungen Garantien und anderen zugeh rigen Dokumente k nnen im eigenen Ermessen von Horizon Hobby Inc jederzeit ge ndert werden Die aktuelle Produktliteratur finden Sie auf horizonhobby com unter der Registerkarte Support f r das betreffende Produkt Spezielle Bedeutungen Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet um auf unterschiedlich hohe Gefahrenrisiken beim Betrieb dieses Produkts
92. together Thoroughly scratch the mating surfaces with a hobby knife Mix epoxy and micro balloons and glue the pieces together Using a small clamp hold the pieces together for better adhesion 49 THROTTLE SERVO INSTALLATION e e e 14 Once epoxy is set install the blind nuts using the M3x16mm screws and Dry fit the throttle servo if there is any binding use a small file and open up Insert the servo into the tray and mark the mounting locations 2 5mm ball driver the servo tray 50 THROTTLE SERVO INSTALLATION e e 17 Using a drill and 1 16th drill bit drill 4 holes Run the servo screws in the holes and back them out Apply thin CA wait until Temporarily mount the engine Enlarge the hole in the DA throttle arm by using CA dries and mount the throttle servo 3 32 inch and 7 64 inch drill bits respectively 51 THROTTLE SERVO INSTALLATION e e e L110 L111 012 Mark the engine dome in the location shown for throttle rod then remove the Use 1 8 unch and 7 64 inch drill bits to drill a hole in the marked location Prepare the throttle rod by installing the clevis and ball link Measure 98mm engine between ball link and clevis and using a felt pen and mark the end of the clevis on the threaded rod This is an approximate length and may need adjusting depending of the location of the servo tray Remove the clevis 5
93. transmitter if necessary 2 Check the movement of the elevator with the radio System Moving the elevator stick toward the bottom of the transmitter will make the airplane elevator move up 3 Check the movement of the ailerons with the radio sys tem Moving the aileron stick to the right will make the right aileron move up and the left aileron move down 4 Use a ruler to adjust the throw of the elevator ailerons and rudder Aileron LOW Up 70mm expo 40 Down 70 mm expo 40 HIGH 140 mm deg expo 65 140 mm deg expo 65 RUDERAUSSCHLAGE 1 Schalten Sie den Sender und Empfanger ihres Modells ein Pr fen Sie die Seitenruderaussschl ge mit dem Sender Bewegen Sie den Seitenruderstick nach rechts sollte sich das Ruder auch nach rechts bewegen Reversieren Sie falls notwendig die Funktion am Sender 2 Pr fen Sie die H henruderfunktion am Sender Ziehen Sie den H henruderkn ppel nach hinten sollte sich das Ruder nach oben bewegen 3 Pr fen Sie die Querrruderfunktion mit dem Sender Bewegen Sie den Querruderstick nach rechts bewegt sich das rechte Querruder nach oben und das linke Querrruder nach unten 4 Querruder NIEDRIGE HOHE Rauf 19 deg expo 25 26 deg expo 30 Runter 11 5 deg expo 25 16 5 deg exp 30 H henruder NIEDRIGE HOHE Rauf 15 deg expo 40 35 deg expo 45 Runter 15 deg expo 40 35 deg expo 45 D BATTEMENTS 1 Mettez l metteur et le r cepteur sou
94. ude Once at about 100 feet of altitude trim the model for lev el flight at 5 8 throttle You will find the Super Decathlon to be very gentle on the controls and feel quite light on the sticks The model is capable of all the basic aerobatic maneuvers loops rolls stall turns inverted flight etc We hope you enjoy your Hangar 9 Super Decathlon as much as we have 94 FLIEGEN Die Super Decathlon ist ein sehr gutm tiges Modell beim Fliegen und am Boden Der Start ist einfach und die Landungen sind Dank geringer Geschwindigkeit sehr berechenbar Beginnen Sie mit der Voflugkontrolle pr fen Sie alle Ausschl ge und versichern sich dass diese in die richtige Richtung laufen Stellen Sie die Leerlaufdrehzahl richtig ein Rollen Sie in Startposition gegen den Wind Geben Sie langsam Gas und halten die Startrichtung mit dem Seit enruder Das Heck des Flugzeuges wird schnell abheben Haben Sie Vollgas gegeben und die Abhebegeschwin digkeit erreicht ziehen Sie etwas am H henruder und die Super Decathlon wird abheben und in den Steigflug bergehen Nach dem ersten Steigflug lassen Sie das H henruder etwas nach und steigen langsam weiter auf ca 30 Meter H he Trimmen Sie in dieser H he bei 5 8 Gas das Modell aus Sie werden feststellen dass das Modell sehr gutm tig re agiert und leicht zu fliegen ist Sie k nnen mit der Super Decathlon Basiskunstflugman ver wie Loopings Rollen Turns R ckenflug etc fliegen Wir h
95. uita dal corretto bilanciamento del modello 1 Fissare i pannelli delle ali alla fusoliera Assicurarsi di collegare i connettori degli alettoni ai connettori ap propriati del ricevitore Assicurarsi che i connettori non fuoriescano dalla fusoliera prima di serrare i bulloni delle ali Il modello deve essere pronto per il volo prima del bilanciamento 2 3 Quando si bilancia l aeromodello assicurarsi che sia assemblato e pronto per il volo Sostenere l aereo in posizione dritta con le dita o con un supporto disponi bile in commercio in corrispondenza dei contrassegni fatti sulla parte superiore dell ala Questo il punto di bilanciamento corretto per l aeromodello 4 Il centro di gravit dovrebbe essere molto vicino ai componenti installati come mostrato nel presente manuale Se il muso dell aereo tende verso il basso spostare le batterie verso la parte posteriore dell aeren Se la coda tende verso il basso aggiungere peso al muso dell aereo Presso i negozi di articoli di hobbis tica sono disponibili pesi autoadesivi HAN3626 adatti a questo scopo A ATTENZIONE necessario regolare il centro di gravit e bilanciare correttamente l aeromodello prima di andare in volo CONTROL THROWS 1 Turn on the transmitter and receiver of your model Check the movement of the rudder using the transmit ter When the stick is moved to the right the rudder should also move right Reverse the direction of the servo at the
96. urnie avec les accessoires du servo Applicare dell adesivo frenafiletti alla vite centrale del braccio del servo e as sicurarsi di utilizzare la rondella elastica fornita con gli accessori del servo 23 AILERON SERVO INSTALLATION AND HINGE LINE SEALING Dry fit the hatch in the wing opening if any interference grind the corner Connect a JR Heavy Duty 18 inch extension to the outboard servo and a Pass a rod through the root to the servo box and tape the servo extension to using a rotary tool and sanding drum Remove a little at a time and check Do 6 inch to the inboard servo Use a string and masking tape to secure the the rod and pull through the wing root not remove too much and get close to the mounting location connection 24 AILERON SERVO INSTALLATION AND HINGE LINE SEALINGe LIL113 0014 aw p nitorem mee pes Install the hatch Install the ball links to the threaded rod provided 0015 Adjust the ball links so that it measures 33 7mm between the end of ball links Make all the aileron linkages the same exact lengths 25 AILERON SERVO INSTALLATION AND HINGE LINE SEALINGe 0016 0017 Install the ball link on the control horn using crescent wrench and 2 5mm Install the ball link on the servo arm using a crescent wrench and 3 32 inch Adjust the servo travel using a computerized transmitter or a JR ball driver bal
97. utenzione del prodotto o di combinazioni di vari prodotti Quindi Horizon non accetta nessuna responsabil it per danni o lesioni derivanti da tali circostanze Con l utilizzo e il montaggio del prodotto l utente acconsente a tutte le con dizioni limitazioni e riserve di garanzia citate in questa sede Qualora l utente non fosse pronto ad assumersi tale respon sabilit associata all uso del prodotto si suggerisce di restituire il prodotto intatto mai usato e immediatamente presso il venditore Indicazioni di sicurezza Questo un prodotto sofisticato di hobbistica e non un giocat tolo Esso deve essere manipolato con cautela con giudizio e richiede delle conoscenze basilari di meccanica e delle facolt mentali di base Se il prodotto non verr manipolato in maniera sicura e responsabile potrebbero risultare delle lesioni dei gravi danni a persone al prodotto o all ambiente circostante Questo prodotto non concepito per essere usato dai bambini senza una diretta supervisione di un adulto Il manuale del prodotto contiene le istruzioni di sicurezza di funzionamento e di manutenzione del prodotto stesso E fondamentale leggere e seguire tutte le istruzioni e le avvertenze nel manuale prima di mettere in funzione il prodotto Solo cos si eviter un utilizzo errato e si preverranno incidenti lesioni o danni Domande assistenza e riparazioni Il vostro negozio locale e o luogo di acquisto non pu fornire garanzie di assiste

Download Pdf Manuals

Related Search

Related Contents

BTL5-_-M_-J-DEXC-TA12 Micropulse Positionsaufnehmer  用具が不調で芝生が刈れていない    Rubbermaid FG374901OLVSS Instructions / Assembly  Hittin` Hoops Manual  ICC ICCMSCMA82  KIRA N7000 Preguntas Frecuentes  

Copyright © All rights reserved. Failed to retrieve file