Samsung SW1485Z1 دليل المستخدم
Contents
1. Note 2 Select RINSE and SPIN ee ae POROA e If more rinsing is necessary RINSE Adjust the rinsing frequency and spinning time fits a START 3 Press Start Hold button close the lid select the rinsing water supplement SPIN INSTALLATION amp MAINTENANCE The User s Manual is for common use Make use of the User s Manual depending upon your washing machine model ENVIRONMENT Never install the washer near water Leave some space Do not place the washer in steamy rooms or where the Maintain at least 10cm between the washer and the wall washer is directly exposed to rain Moisture may destroy the Place the washer on a sturdy flat surface electrical insulation causing an electrical shock hazard If the washer is placed on an uneven or weak surface Avoid direct sunlight or heaters noise or vibration occurs Allowable is 1 As plastic and electrical components are affected by direct Adjust the legs for even placement heat never place the washer near furnaces boilers etc Do not place under direct sunlight gt LEVELLING if the washer is not leveled with the ground it makes the machine tremble more or be out of order So make sure that the washer is leveled properly Adjust the height control legs to make eve Adjustment of height If not leveled adjust the legs to level the washer e Be careful not to put in your hand under the legs Look It may cause some injury Lock Nut iis z A Adjustable A2. Select HEAVY course button 3 Press START HOLD button Put the detergent softener in proportion to the water level and then close the lid e Here adjusted soaking course during 20 minutes to remove the heavy dirt at the collar of laundry When need more soaking press wash button select 40 minute soaking time manually e The washing board and tub spinning in the opposition way gives great efficiency washing Put the laundry into the washer and add detergent too Be careful not to overload Use right detergent for the fabrics you are washing START gt SPEEDY COURSE powe gt seny gt gt START For laundries with light dirt like towels in a short time 1 Put the laundry in the washer and press the POWER button to on 2 Select SPEEDY course button 3 Press START HOLD button Put the detergent softener in proportion to the water level and then close the lid e Spinning the washer board brings high energy efficiency e In case of heavy laundry it automatically spin the washer tub to improve the power of washing Note Measuring the weight of laundry washer moves its body without water in every courses and then indicates adequate water level and amount of detergent except clean tub course Every course automatically indicates the water temperature and also it can be selected by pressing the water temperature button as you want except wool course gt BLANKET COURSE Power gt stawer gt START
3. the part c is released the hose is automatically connected to the adaptor making a click sound gt ASSEMBLING THE RAT PROTECTION PANEL ep Tilt the washer a little and lift up the panel until it clicks 1 Insert the sound finally fix the panel with screw to the base as shown absorbing panel in the figure to the assembling hole on front side to the end Anti rat cover __ Rear side 2 lf you have difficulty inserting the panel lift up the washer a little and insert it 5 gt IN CASE OF PUMP DRAINED WASHER ep Take out the cap hose and Be sure to join tightly the drain hose into Be sure to join tightly the drain Install the drain hose in the connect the outlet hose the drain outlet on the back of the hose into the drain outlet position of about 90 100cm machine on the side of the machine above the ground cap hose 5 gt o i l a outlet hose gt CONNECTING THE DRAIN HOSE p After pressing the joint ring a insert the drain hose b to drain direction gt HOW TO ADD THE FABRIC SOFTENER Cpt e When a proper amount one time does of fabric e Do not open the lid during the Spin Dry cycle softener is stored in the softener inlet it is If added too early its effectiveness will decrease automatically put in at the last rinsing cycle Do not leave the softener Do not use detergent bleach or starch into into the Soften
4. washi wi pea Rei and spinning j BLEACH INLET PULSATOR FRONT CONTROL PANEL ADJUSTABLE LEGS Adjust the length of the legs when installing the washer poeareceatoanteeeera s WATER SUPPLY HOSE HOT leet ee ty WATER SUPPLY HOSE COLD DRAIN HOSE PUMP DETERGENT BOX SPIN BASKET POWER CORD GROUND LEAD When the water pipe is metal make sure to cover the end of the ground wire WATER DRAIN HOSE SOUND ABSORPTION PANEL abate Jopo auiyovu Surysvm nof uodn Sutpuadap pnuvy sasn ayy fo asn ayvyy ISN UOWWOI sof S1 JUNULIY S 49ST MI SL Vd JO NOILdJIN SIA CONTROL PANEL For more details see control panel of your washing machine gt gt POWER BUTTON POWER e Select it when you put the power to ON or OFF e Automatically turned off after washing e Automatically turned off without pressing any other button for 10 minutes in power off condition gt START HOLD BUTTON e Press it when you start or want to pause DELAY gt gt DELAY START BUTTON START e Use this function when you finish the washing on the time you want Press power to OFF in order to cancel the reservation WASH gt WASH BUTTON e Use this function when you want to wash separately or adjusting the washing time 5 minutes 20 minutes e Keep pressing this button when choosing soak washing gt RINSEBU
5. For big laundry like quilts or bedcovers 1 Put the laundry in the washer and press the POWER button to on 2 Select BLANKET course button 3 Press START HOLD button Put the detergent softener in proportion to the water level and then close the lid e Blanket may get stained with the detergent Therefore detergent in the liquid detergent device is suggested gt WOOL COURSE For laundries with wool washing mark like sweaters cardigans or delicate clothes START POWER gt WOOL gt san 1 Put the laundry in the washer and press the POWER button to on Be sure the weight of laundry is less than 2kg 2 Select WOOL course button e Select the adequate water level manually in case of light laundry for the size 3 Press START HOLD button Put the detergent softener in proportion to the water level and then close the lid e Slightly dry the laundry at the last to avoid wrinkles e Cold water only be selected e Use neutral detergent e Spinning into a side together or spinning the washer board only prevent the damage on the laundry gt SHIRT COURSE STARR For shirts with dirt on the collar oD Sa HOLD or cuff 1 Put the laundry in the washer and press the POWER button to on 2 Select SHIRT course button 3 Press START HOLD button Put the detergent softener in proportion to the water level and then close the lid e Adjusted 20 minutes soaking to remove the heavy dirt on the collar e The washing board an
6. I A Lege A D e After slightly lifting up the machine rotate the adjustable leg counter clockwise and pull as much as need to adjust the reight Pull the handles located at the right and left of the front side and slide off Adjust the water drop mark to be in the red circle pulling back the machine slightly and then After putting down the machine after adjustment push it with a feet to fix T ae Wea Unlock e Adjust the height and secure Fix the handles by hand e Secure the lock nut by rotating it firmly completely e If the lock nut is not secured the adjustable leg may be released Waterdrop mark Cause How to level ka The front part is Level it by adjustable legs T ower aa The back part is Adjust the height by using the adjustable rubber re lower or prop at the back Pos The left part is Adjust the left part by using the adjustable legs ve lower i at the front and the adjustable rubber at the back FR The right part is Adjust the right part of the washer by using the adjustable leg D lower at the front and the adjustable rubber at the back gt LEVELLING TypeB SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB e Open the lid of the machine pour water into the tub up to the level 1 Adjust the side horizontally just below the pulsator and adjust the legs so that the pulsator is first and the front positioned at the center of the wate
7. TTON SE e Select this function when you want to rinse only and change the rinsing frequency e You can choose maximum 5 times SPIN gt SPIN BUTTON e Select this button when you want to spin only and adjust the spinning time minute 7 minutes e If you want to protect wrinkles in spinning select this button for 1 minute spinning e If you select Spin only there is a gap shown between the timer for spinning and the timer for whole working which included more time for draining and holding gt LEVEL METER e Set it for the water drop to come in the center moving the adjustable legs SUPER J gt SUPER RINSE BUTTON S e Use this function when you want clean rinsing with more of water than washing e Available to rinse in one step more than the water level of washing WASH RINSE gt WATER TEMP BUTTON e Indicates the water temperature automatically but control it manually as occasion demands e WASHING Choose the temperature necessary in washing e RINSING Choose the temperature necessary in rinsing e Alterable in the middle of working gt Adjusting the water temperature automatically you should open the taps of hot water and cold water for optimum washing gt In case of not opening the tap of hot water or the hot water not being supplied can not control the water temperature and do washing with cold water only 3 In case of wool course cold water only is selected WATER TEMP INDICATOR e When w
8. WASHING MACHINE Please read this manual before using and note how to use in the proper manner Please be careful of keeping the manual Otherwise it should be bought separately The User s Manual is for common use User s Manual SW1485Z1 FEATURES Pre rereret rere terri tere eri reteer ir eees street tort ees etre ecer irr ect i Ty 1 SAFETY INSTRUCTIONS ELTETE TETESI TTT 2 DESCRIPTION OF PARTS NEEF EIA PTIT EEATT EST 3 CONTROL PANEL oe WASHING PROCEDURE PeCerTeeeereererrere rT er ercre reer eee rT ee Ts 5 Fuzzy course 5 Heavy course 5 Speedy course 5 Blanket course 5 Wool course 6 Shirt course 6 Memory course 6 Clean tub course 6 Delay start 6 MANUAL FUNCTIONS eer eee eee eee eee eee eee eee eee eee eee ee eee eT 7 INSTALLATION amp MAINTENANCE 00eeseneses 8 Environment 8 Levelling 8 Connecting the water supply hose 9 Assembling the part protection panel 10 In case of pump drained washer 10 Connecting the drain hose 10 How to add the fabric softener 10 How to put the detergent in 10 Water supply connector filter 11 Cleaning the filter net 11 How to clean the filter 11 TROUBLESHOOTING ERARA GineBeey esas ganna yeacedoMeeyelgsaces 12 SPECIFICATIONS Make use of the User s Manual depending upon your washing machine model FEATURES DFC SYSTEM e Abbreviation of Digital Freewater Control system As an Ideal combination of Digital temperature control function Digital spin control function Speed control f
9. ace UNBALANCE DOOR OPEN 12 IN CASE THE NEED FOR SERVICING ARISES If any problem occurs with your products do not hestitate to call any nearby Name address telephone number is required SPECIFICATIONS NORMAL WASH 14 kg HIGH 901 CAPACITY SPIN 14 kg MED 80 STANDARD MLOW 701 DIMENSIONS mm W630xD700xH1020 WATER LEVEL LOW 571 WEIGHT 49 kg E LOW 421 0 05 0 78 MPa WATER USAGE 2107 WATER PRESSURE 0 5 8 0 kg fem PULSATOR WASHING TYPE Stirring Type ROTATING SPEED 105 rpm MOTOR WASHING 480W SPINNING TUB 700 rom INPUT SPINNING 180W ROTATING SPEED p MOTOR MAX WASHING NORMAL WASHING Continue pb Ete 480W INPUT SPINNING CAPACITY SPINNING 15 Minutes CODE NO DC68 01091A 03
10. ashing rinsing each course indicates the adequate water temperature automatically e The temperature is indicated in 4 grades Hot water Supply hot water only Effective for heavy dirt and control in 35 C 45 C amp Effective for activating the detergent and control in 25 35 C Cold water Supply cold water only There might be a difference in the water temperature according to water pressure and temperature of hot water WATER LEVEL gt WATER LEVEL BUTTON e Water level is automatically indicated but you can adjust it e Alterable in the middle of working WATER LEVEL DETERGENT INDICATOR e In proportion to the amount of laundry the water level and amount of detergent are automatically indicated e Indicates water level in 10 grades MOVEMENT INDICATOR e Indicates the state of moving inside of clean tub e Shows the water supply and the spinning direction of washing board and tub Indicates the selected washing course and shows error in trouble TIME LEFT DELAY START ERROR SIGN INDICATOR e Indicates the left time until the end of the washing e Indicates advance time e Indicates the trouble in the machine and take an action for the error with them PROCEDURE INDICATOR e Indicates the procedure of washing the remaining time and remaining frequency e In its procedure it flickers e If you select the washing time more than 20 minute soak washing is indicated WASHING PROCEDURE Befor
11. d tub spinning in the opposition way gives great efficiency washing START gt MEMORY COURSE POWER gt MEMORY gt HOLD Memorize the functions frequently used and you can use it easily when washing the next time 1 Put the laundry in the washer and press the POWER button to on e Check to put the functions you need before washing e Refer to the following instruction on how to set up the memory course 2 Press MEMORY course button e Selected functions are displayed on the control panel 3 Press START HOLD button Put the detergent softener in proportion to the water level and then close the lid How to set up memory course 1 Press the POWER button to on 2 Press MEMORY button to on It is shown same as the beginning of Fuzzy course 3 Select the functions frequently used manually such as water temperature time of washing spinning and rinsing 4 Press the momory button one second or more to input selected mode Press the button until buzzer makes sound once more e Press the START HOLD button to run input mode e Repeat the above proceduce to change the Memory mode e Even when power system tums OFF your final input mode is memorized gt CLEAN TUB COURSE in cleaning the washing tub START HOLD POWER gt CLEAN TUB 1 Press the POWER button 2 Press the CLEAN TUB button 3 Press START HOLD button Put the detergent in proportion to water level and close the lid e Soak washing ad
12. djusting the suitable speed of spin in the washing board tub for each washing course and amount of laundry with the digital spin control function It makes proper force of current Therefore it reduces the damage on the laundry and makes the maximum effect of washing e It controls the speed automatically for every course So it does not need to adjust the speed separately POWER INVERTER MOTOR WITH LOW NOISE e Washing in silence by adapting inverter resin motor POWERFUL AND CLEAN STAINLESS WASHING BOARD e Less tangled and damaged laundry through the magic stream of water from the powerful clean washing board even in case of the long term use MAGIC FILTER OF DOUBLE POWER REMAINDERS FILTER Two magic filters completely block the remainders from the laundry regardless with the water level and this is the feature that makes the dirt off with out additional rinsing POWERFUL LIQUID SOAP DEVICE e Automatically convert powder detergent to liquid soap promptly before it flows into the laundry and avoid covering the laundry Therefore it makes sanitary laundry WATER WASTE PREVENTED WASHING MACHINE e Reducing the unnecessary water between the inner amp outside bodies cut down the water consumption SAFETY INSTRUCTIONS Please note that the following precautions for safety intend to prevent unpredictable danger and damage by helping the proper use in safety When using hot water in washing please mak
13. e Even though the water level is auto e Soak washing is available matically set up select the adequate 3 Press START HOLD button close the lid water level according to the laundry 1 Press the POWER button to on Note i A 2 Select RINSE e It water still remains after wash RINSE ONLY e Press the rinse button and select the rinsing select SPIN only frequency Remainder of water to be removed Powe gt Anse gt STAR You can adjust the frequency from 1 to 5 times e Even though the water level is HOLD 3 Press START HOLD button close the lid altomatically set up Selat ime adequate water level in case that the laundry is soaked SPIN ONLY 1 Press the POWER button to on Note 2 Select SPIN olf lect SPIN only there i e Press the spin button and adjust the time of YOU SEEC only neres a gap POA pe gt START spinning shown between the timer for spinning d nop e You can adjust from 1 minute to 7 minutes Ar ll Spa ahs el e The washer spins slowly in order to prevent MEUSE ole Ue eee the clothes being tangled holding So note it does not mean out 3 Press START HOLD button close the lid of order WASH RINSE 1 Press the POWER button to on Note 2 Select WASH and RINSE i WASH e Please adjust the washing time and rinsing It water still remains after wash POWER START frequency select SPIN only HOLD 3 Press START HOLD button Remainder of water to be removed RINSE SPIN 1 Press the POWER button to on
14. e starting washing check the following Connect the water supply hose to the water tap Leave a tap open Plug the power cord in Make sure to lay down the drain hose In case no drain pump gt FUZZY COURSE owen gt START 1 Put the laundry into the washer and push the POWER button to on e Fuzzy course button lights on 2 Press START HOLD button e Measuring the weight of laundry washer moves it s body without water and then indicates adequate amount of water and detergent e The adequate temperature of water is automatically selected 3 Open the lid and put the detergent softener in proportion to the water level indicated Then close the lid When you open the lid in operation it stops washing But water supply will be continued In case of using the hot water only cold water is supplied during the first 20 seconds to avoid damaging the laundry by hot water On it s operation in every course washing time rinsing frequency amp spinning time can be adjusted With the press of the function button on water temperature the water temperature in washing rinsing is selected manually in every course except wool course With the press of the super rinse button additional water is supplied in rinsing the laundry except CLEAN TUB course gt HEAVY COURSE For Jeans or laundry POWER gt HEAVY gt sua with heavy dirt 1 Put the laundry in the washer and press the POWER button to on 2
15. e sure that the water should not exceed 50 C e Plastic parts may be deformed or damaged and an electric shock or a fire may take place WARNING There might be serious injury or fatal accident when you violate this instruction If the power supply cord or plug is damaged or loosened do not use e An electric shock or a fire may take place Do not pull the cord off or touch it with moist hands e An electric shock or a fire may take place Do not bend the power supply cord by force or press it with heavy things e An electric shock or a fire may take place Do not install the washer nearby electric implement or don t put a candle light or cigarette light on the washer e A fire may take place Do not disassemble repair or remodel it recklessly e When you need to repair it please call service agent An electric shock or a fire may take place During operation do not put your hands or metal materials under the washer e You may be hurt by spinning board beneath the washer Stay away from the washer when the bottom of the washer sinks into the water e There might be an electric shock Please wait until the water drains out completely Do not put laundry stained with gasoline benzene or alcohol in the washer and keep the materials away from the washer e An explosion or a fire may take place During spinning don t put your hand in the spinning tub e It may hurt your hands If it does not stop within 15
16. er the Softener Inlet Dispenser for a long time e Using too much softener may produce Because softner became stiff s unsatisfactory results gt HOW TO PUT THE DETERGENT IN ep 1 Open the detergent box by pulling in the direction of the arrow as shown in the figure and then put the powder detergent in the detergent box 2 Put in one time amount of detergent evenly so the detergent may not brim over the box eeen Detergent Device eteeeeeeeneeeeesessessasesesessseeeeessesenensnenenanes Put the detergent i in proportion fo water level Softener Device Softener baseline TI CAUTION If softener is stored over the above base line it may flow down at any time 10 gt WATER SUPPLY CONNECTOR FILTER B o 4 oS ma aia vo valve 1 Pull out the filter and wash well 2 Pull in the filter and connect 3 Check if there is a leakage the hose to the inlet water Note to tighten up the valve tightly connector gt CLEANING THE FILTER NET Clean the filter net often to keep the washer clean Opt Sy Mi k 1 Push the upper part 2 Open the cover as 3 Clean the filter 4 Close the cover and insert the of the filter and pull in shown in the figure lower part of the filter in the basket first and then push the filter with click sound 1 Push up and 2 Remove the collected 3 Clean the filter 4 Pull down the filter net pull out the filter net lint from the filte
17. justed e Water temperature select button only adjustable e Ideal detergent powder bleach e Remove the dirt in the outer wall of the washing tub with powerful stream of current START HOLD DELAY POWER START gt DELAY START 1 Put the laundry in the washer and press the POWER button to on e Make sure to open the tab 2 Press DELAY START course button 1 Increase one hour more each press from 3 hours and you can select by maximum 19 hours 2 After selected time is over it finishes washing e You can choose a course separately as you want 3 Press START HOLD button Put the detergent in proportion to water level and close the lid Be sure of putting the detergent into the liquid soap device e In case of putting the detergent into the laundry directly it may be discolored according as the reservation is longer e Press the power button in order to cancel the reservation e It could be finished at slightly different time due to the water pressure MANUAL FUNCTIONS Each washing course changes manually Ex If you want to wash in the speedy course Power Select speedy course Wash Start Hold button Note WASH ONLY i Beal tiga buttona on e It water still remains after wash e Press the wash button and adjust the washing time Select SPIN only stant You can adjust the washing time from 5 to Remainder of water to be removed POWER gt WASH gt HOLD 20 minutes per one minut
18. r as shown in the figure in same direction next e Place the machine more than 10cm away from the wall Water 2 If the thread is not T within the limit adjust e Adjust the legs on feet the height of for levelling the legs AA Loosen S Lock gt gt CONNECTING THE WATER SUPPLY HOSE 1 Remove the adaptor from the water e Lonnect the other end of the water supply hose to the inlet water valve supply hose at the back of the washer Screw the hose clockwise all the way in 2 First using a type faConnect the other end of the water screw driver loosen the Supply hose to the inlet water valve four screws on the adaptor J at the top of the washer Next take the adaptor and Z Screw the hose clockwise all the way in turn part b following the arrow for gap about 5mm between them 3 Connect adaptor to the water tap by tightening the screws firmly Then turn part b following the arrow and put a and b together Pe water tap is a screw type assemble a water supply hose that fits to the f tap as shown g ry NOTICE After completing connection if water leaks from the hose then repeat the same steps Use the most conventional type of faucet for water supply In case the faucet is square or too big remove the spacing ring before inserting the faucet into the adaptor 4 Connect the water supply hose to the adaptor Pull down the part c of the water supply hose When
19. r net gt HOW TO CLEAN THE FILTER opt 1 Place a rag under the washer filter not to wet the floor pump drained washer 2 Rotate the filter counterclockwise 1 Place a rag under washer filter not to wet the floor and pull out the filter 2 Turn the filter cap to the left 3 Remove dirts and rotate 3 Take the filter out and y FILTER the filter clockwise OPEN S remove dirts All aos until it locks in position 4 Reassemble in RAG reverse order 11 TROUBLESHOOTING gt WASHING MACHINE WON T WORK gt CHECK YOUR VOLTAGE Is the water tap opened If the voltage power supply ia Is the washer plugged in is either too high or too low Safe Is the power cut off it appears with a buzzer Is there enough water Check voltage Call to service center or agency gt WATER IS NOT SUPPLIED Is the water tap opened Is the water cut off Is the water supply hose or hose connection clogged Is the water tap frozen If water is not supplied in 1 hour a buzzer will sound and the remaining time indicator will show WATER ERR WATER ERR gt WATER DOSE NOT DRAIN Is the drain hose down No pump Is the drain hose frozen Is the drain hose clogged If the water dose not drain in 15 minutes a buzzer will sound and the remaining time indicator will show DRAIN ERR gt SPINNING DOES NOT WORK Is the laundry spread out evenly in the washer Is the washer set on a sturdy flat surf
20. seconds after you open the lid call service agent immediately CAUTIONS There might be a slight injury or damage when you violate this instruction Don t install it in the area with moisture or outdoor where it has rain or snow e An electric shock or a fire may take place Please unplug the power supply cord when you do not use it e An electric shock or a fire may take place If there is dust or water on the power supply plug and its connected part please remove it completely e An electric shock or a fire may take place Do not make your kids look into the inside of the washer e If your kid falls into the washer his life could be in danger Ventilate immediately without touching the power plug if gas is leaking e An electric shock or a fire may take place if it catches flame If the washer makes strange noise smell or smoke unplug it promptly and call service agent e An electric shock or a fire may take place When cleaning don t spray water to the parts of the washer directly e It may make it s life span shorten Also an electric shock or fire may take place Don t use several appliances together with an outlet e A fire may take place due to unusual heat Don t press the button with an awl or pin e An electric shock or a fire may take place FILTER TE Lint will be collected in the filter during washing FABRIC SOFTENER DISPENSER opto closed during
21. unction It controls the water tem perature way of rotation speed properly accord ing to the clothes This system cleans the heavy dirt completely and delicately without damaging the clothes DIGITAL TEMPERATURE CONTROL FUNCTION e Washing detergent has it s own temperature for the maximum activation The water temperature for this activation is slightly different according to the detergents but normally it shows the best effect in 30 C 45 C Digital temperature control function the water in the optimum temperature mixing the hot water and cold water properly with the censor in the washer tub e In each course the optimum water temperature is automatically set up but you can adjust the water temperature manually DIGITAL SPIN CONTROL FUNCTION e Realizing multi rotary manners proper to the laundry control the rotation of washing board tub and make the washing minutely without damaging the laundry It makes swift current by spinning the washing board and tub each in an opposite direction in heavy dirt course In light dirt course increase the energy efficiency spinning the washing board only In case of highclass clothes spinning the washing board tub in one direction together and making the smooth current like hand washing It reduces the damage on the clothes e No need to adjust the manner of spin separately as it automatically sets up the optimum manner of spin in each course DIGITAL SPEED CONTROL FUNCTION e A
Download Pdf Manuals
Related Search