Home

Samsung 9.000 Btus

1. How to connect your extended power cables Items to prepare compressor and insulation tape should be prepared by an installation technician Tools Crimping plier Connection sleeve mm Insulation tape Contraction tube mm Spec MH 14 20x 7 0 HxOD Width 18mm 50x 8 0 LxOD m Fa Shape GD GD a n EL 1 As shown in the figure peel off the shields from the rubber wire of the power cable Peel off 20 mm of the wire shields of the tube installed already A After peeling off the tube wire you must insert a contraction tube CAUTION 2 Insert both sides of core wire of the power cable into the connection sleeve 3 Using a compressor compress the two points and flip it over and compress another two points in the same location D The compression dimension should be 8 0 After compressing it pull both sides of the wire to make sure it is firmly pressed 4 Wrap it with the insulation tape twice and position your contraction tube in the middle of the insulation tape 6 After tube contraction work is completed wrap it with the insulation tape to finish 5 Apply heat to the contraction tube to contract it Unit mm Power cable provided by us V8 Compress it 4 times 5mm Insulation tape Minm 40mm Contraction tube tape Incase of extending the electric wire please DO NOT use a round shaped pressing socket WARNING Panama_IB
2. Cleaning the air conditioner I Removing the Air filter Grab the handle and lift it up Then pull the Air filter towards you and slide it down Cleaning the air filter Washable foam based air filter captures large particles from the air The filter is cleaned with a vacuum or by hand washing Open the panel and put the Air filter out Clean the Air filter with a vacuum cleaner or soft brush 2 gt If dust is too heavy rinse it with running water o Pa Insert the Air filter back in its original position Dry the Air filter in a ventilated area and close the front panel Clean the Air filter every 2 weeks or when the filter clean reminder lights up Cleaning term may differ depending Note onthe usage and environmental conditions In dusty area clean it once a week Ifyou turn off the air conditioner by pressing Power 9 button the filter clean reminder will be turned off Ifthe Air filter dries in a confined or humid area odors may generate If it occurs re clean and dry it in a well ventilated area 18 Panama_IBIM_34042A_EN 4 indd 18 2015 7 10 140033 Maintaining the air conditioner If the air conditioner will not be used for an extended period of time dry the air conditioner to maintain it in best condition 1 Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and disconnect the power plug There may be internal damage if moisture is left
3. Drainage Grounding conductor connection Correct operation follow the steps below 1 Press the Power button and check the following gt The indicator on the indoor unit lights up gt The airflow blade opens and the fan gears up for operation 2 Press the Mode button to select Cool mode gt In Cool mode use Temp or button and set the temperature at 16 C Approximately 3 5 minutes later outdoor unit will start to operate and the Cool air will blow out NOTE After 12 minutes of stationary condition check the indoor unit air treatment Cooling mode indoor unit check Inlet air temp Outlet air temp From 10 K to 12 K indicative delta T D 3 Press the Air swing button and check the following amp The airflow blades work properly 4 Press the Power button to stop the operation When you complete the installation successfully hand over this manual to the user for storage in a handy and safe NOTE place Pump down procedure when removing the product 1 Turon the air conditioner and select Cool mode to run the compressor for 3 minutes 2 Release the valve caps on High and Low pressure side 3 UseL wrench to close the valve on the high pressure side 4 Approximately 2 minutes after close the valve on the low pressure side 5 Stop operation of the air conditioner 6 Disconnect the pipes 38 Panama IBIM 34042A EN 4 indd 38 2015 7 10 14 04 42
4. Cancel Press the Turbo button once again Turbo function is only available in Cool mode NOTE Ifyou press the Mode button while the Turbo function is on it will cancel the function Temperature Fan speed cannot be adjusted while using this function 12 Panama IBIM 34042A EN 4 indd 12 2015 7 10 14 04 29 good sleepmode For a comfortable sleep the air conditioner will operate it Fall asleep gt Sound sleep gt Wake up from good sleep mode When the air conditioner is on and in cool mode fi 1 Press the good sleep button on the remote controller 2 did gt good sleep indicator appears and Off timer indicator starts blinking on the remote a h T Temp Fan controller display A d light E 2 Press the good sleep button to set the time ET gt You can set the time in half hourly unit from 30 minutes 3 hours and hour unit from Auto Temp good Clean Humi lov 3 hours 12 hours Filter Reset BeepOff Disk b Operating hour can be set from minimum 30 minutes to maximum Set 12 hours is me lame b Default operation hour is set to 8 hours Cool 3 Press the Set Cancel button to active it on gt Off timer indicator stops blinking and reserved time will be displayed for 3 seconds Then the air conditioner operates in good sleep Cool mode rim Lite SM GED gt Ifyou don t press Set Cancel button within 10 seconds after pressing the good sleep button the air
5. Check if the appliance is running in a smoky area Ventilate the room or operate the air conditioner in Fan mode for 1 2 hours We do not use smelly components in the air conditioner 20 Panama IBIM 34042A EN 4 indd 20 2015 7 10 14 04 34 PROBLEM SOLUTION Error is indicated When an indoor unit indicator blinks contact the nearest service center m 2 Noise is generated Depending on the status of the air conditioner usage noise can be heard when refrigerant flow movement changes It is normal Water is dropping from Water may be generated because of the temperature difference It is normal the outdoor unit piping connection 21 Panama IBIM 34042A EN 4 indd 21 2015 7 10 14 04 34 INSTALLATION PARTS X In this manual you may find model names written in simplified forms as indicated in following table Model Names Included Models Remark AQ ASXXTX AQ AS 09T AQ AS12TX AQ AS 18T AQ AS 24T Grouping was done by series AQ AS U AQ AS OOUX AQ AS T2UX AQ AS 18UX AQ AS 24U 09 AQ AS 09T AQ AS 09U 12 AQ AS12T AQ AS12U ee AQ ASISTX AQ AS18UX Grouping was done by capacity 24 AQ AS24T AQ AS24U Safety precautions Carefully follow the precautions listed below because they are essential to guarantee the safety of the equipment Always disconnect the air conditioner from the power supply before
6. Panama IBIM 34042A EN 4 indd 1 2015 7 10 14 04 25 EENE o Features of your new air conditioner Contents I Cool Summer Offer USING PARIS On those hot sweltering summer days and long restless nights there is no better escape from the heat than the cool comforts of home Your new air conditioner brings an end to exhausting hot summer days and lets you rest Beat the heat with your own air conditioner this summer I Cost Efficient System Your new air conditioner not only provides maximum cooling power in the summer but also can be an efficient heating method in the winter with the advanced Heat pump system Heat pump system is 3 times more efficient compare to the other electrical heating appliance so you can further reduce its running cost Now meet year round needs with one air conditioner I Look for Everywhere The elegant and harmonious design gives priority to the esthetics of your space and complements any of your existing interior d cor With its soft color and rounded edge shape the new air conditioner adds class to any room Enjoy what your air conditioner offers both functionally and esthetically good sleep function good sleep function allows you to set a comfortable sleep temperature while saving energy and having sound sleep Virus Doctorfunction generates hydrogen H and oxygen O to attack undesirable air contaminants such as bacteria pollen and odor It makes you breath
7. If the doors or windows are open it may cause bad cooling performance Close the doors and windows Check if the air conditioner has just been turned on after stopping cooling operation In this case just a fan will run to protect the outdoor unit compressor Check if the pipe length is too long When the pipe length exceeds maximum allowable pipe length cooling performance may decrease Air flow adjustment is not working Checkif you have selected Auto Dry good sleep mode In these modes desired temperature is set to auto and you cannot adjust the temperature Fan speed adjustment is not working Check if you have selected Auto Dry Turbo good sleep mode In these mode fan speed is set to Auto and you cannot adjust the fan speed Remote controller is not working Check if your batteries are depleted Make sure nothing is blocking your remote controller sensor Check that there are strong lighting apparatus near the air conditioner Strong light which comes from fluorescent bulbs or neon signs may interrupt the electric waves Timer function does not set Check if you press the Set Cancel button on the remote controller after you have set the time The indicator is blinking continuously Press the Power button or disconnect the power plug switch off the auxiliary power switch If the indicator is still blinking contact the service center Odors permeate in the room during operation
8. Panama IBIM 34042A EN 4 indd 22 2015 7 10 14 04 34 Installing the unit IMPORTANT When installing the unit always remember to connect first the refrigerant tubes then the electrical lines Always disassemble the electric lines before the refrigerant tubes gt Upon receipt inspect the product to verify that it has not been damaged during transport If the product appears damaged DO NOT INSTALL it and immediately report the damage to the carrier or retailer if the installer or the authorized technician has collected the material from the retailer HSITDNA gt After completing the installation always carry out a functional test and provide the instructions on how to operate the air conditioner to the user gt Do not use the air conditioner in environments with hazardous substances or close to equipment that release free flames to avoid the occurrence of fires explosions or injuries To prevent injury when accidentally touching the indoor unit fan install the indoor unit at least 2 5m above the floor gt The air conditioner should be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry gt Our units must be installed in compliance with the spaces indicated in the installation manual to ensure either accessibility from both sides or ability to perform routine maintenance and repairs The unitscomponents must be accessible and that can
9. 34 pao 27 Panama IBIM 34042A EN 4 indd 27 2015 7 10 14 04 38 Fixing the installation plate 2 Fix the indoor unit If you fix the indoor unit on a wall 1 Fixthe installation plate to the wall giving attention to the weight of the indoor unit pasas BE ng Ifyou mount the plate to a concrete wall using plastic anchors make sure that gaps 220mm 4 Oh between the wall and the plate created by projected anchor is less than 20mm NOTE If you fix the indoor unit on a window frame If you fix the indoor unit on a gypsum board 1 Determine the positions of the wooden uprights to be 1 Use stud finder to find out locations of the studs attached to the window frame 2 Fix the plate hanger on two studs 2 Attach the wooden uprights to the window frame giving attention to the weight of the indoor unit 3 Attach the installation plate to the wooden upright using tapping screws Search for other spots if there are less than two studs or the distance between the studs are different from the A plate hanger Fix the installation plate without inclining to one side CAUTION e Make sure that a wall can withstand the weight of the product If you install the product in a place where it is not warning strong enough to withstand the product weight the unit could fall and cause injury Connecting the assembly cable Cable specification Model Power c
10. 4 Puta flare nut slightly into the pipe and modify the flare Outer Diameter D Depth A Flaring Size B 96 35 mm 1 3mm 8 7 9 1 mm 99 52 mm 1 8 mm 12 8 13 2 mm 612 70 mm 2 0 mm 16 2 16 6 mm 615 88 mm 2 2mm 19 3 19 7 mm 31 Panama IBIM 34042A EN 4 indd 31 2015 7 10 14 04 30 Cutting or extending the pipe 5 Check if you flared the pipe correctly see examples of incorrectly flared pipes below Correct Inclined Damaged Cracked Uneven Surface Thickness 6 Align the pipes to connect them easily Tighten the flare nuts first with your hands and then with a torque wrench applying the following torque Torque Flare nut Outer Diameter Nem kgf cm 96 35 mm 14 18 140 180 99 52 mm 34 42 350 430 912 70 mm 49 61 500 620 915 88 mm 68 82 690 830 Indoor outlet pipe Connecting pipe Excessive torque can be cause of gas leakage In case brazing the pipe the nitrogen gas must be blown into the note pipe 50 Pa The joint must be accessible and serviceable 7 For further details on how to connect to the outdoor unit and purge the air refer to page 34 35 Tighten the flare nut with torque wrench according to specified method caution __ f the flare nut is over tightened the flare may break and cause refrigerant gas leakage Installing and connecting the drain hose of the indoor unit When installing the drain hose for the indoor unit check if
11. Do not use a damaged power plug damaged power cord or loose wall socket gt This may result in electric shock or fire Do not pull the power cord when unplugging the power plug gt Unplug the power plug by holding the plug gt Failing to do so may result in electric shock or fire Do not pull or excessively bend the power cord Do not twist or tie the power cord Do not hook the power cord over a metal object place a heavy object on the power cord insert the power cord between objects or push the power cord into the space behind the appliance gt This may result in electric shock or fire FOR POWER SUPPLY _ XCAUTIoN When not using the air conditioner for a long period of time or during a thunder lightning storm cut the power at the circuit breaker gt Failing to do so may result in electric shock or fire FOR USING WARNING Q 4 Panama IBIM 34042A EN 4 indd 4 2015 7 10 14 04 26 If the appliance is flooded please contact your nearest service center gt Failing to do so may result in electric shock or fire If the appliance generates a strange noise a burning smell or smoke unplug the power plug immediately and contact your nearest service center gt Failing to do so may result in electric shock or fire In the event of a gas leak such as propane gas LP gas etc ventilate immediately without touching the power plug Do not touch the appliance or power cord gt Dono
12. after about 10 minutes This procedure is very important to avoid a gas leak gt Close the valve of the low pressure side of manifold gauge clockwise gt Turn off the vacuum pump gt Check for 2 minutes if there is any pressure change b Remove the hose of the low pressure side of manifold gauge 6 Seta valve cork of liquid and gas service port to the open position Outer Diameter Nem Torque kgf cm 66 35 mm 14 18 140 180 99 52 mm 34 42 350 430 612 70 mm 49 61 HSITDNA 500 620 015 88 mm 68 82 690 830 Manifold gauge Valve Gas service port lt Low pressure gt Liquid service port lt High pressure gt Lf Vacuum Pump Backward flowing prevention Po I Adding Refrigerant Add refrigerant charge according to table below A4 or 5 meter pipe is supplied with the air conditioner If you use a pipe longer than 4 or 5m Ag of refrigerant R22 must be added for each extra meter If you use a pipe shorter than 4 or 5m The purge time is normal Refer to the Service Manual for further details Model 09K TDK 9180k 24K 20 20 25 The remaining air in the Refrigeration cycle which contains moisture may cause malfunction on the compressor caution Always contact the service center or a professional installation agency for product installation Panama IBIM 34042A EN 4 indd 35 35 2015 7 10 14
13. air conditioner will cool your room You can adjust the temperature and the fan speed to feel cooler in hot season If current outside temperatures are much higher than the selected indoor temperature it may take time to bring the inner temperature to the desired coolness Dry The air conditioner in Dry mode acts like a dehumidifier by removing moisture from the indoor air Dry mode makes the air feel refreshing in a humid climate To maximize the dehumidification capacity during the Dry operation the air conditioner could be operating at lower or higher temperature than the remote controller set temperature Fan Fan mode can be selected to ventilate your room Fan mode will be helpful to refresh the stale air in your room 10 Press the button to turn on the air conditioner Press the button to set the operating mode Each time you press the Mode button the mode will change in order of Auto Cool Dry and Fan HSITDNA Press the button to set the desired fan speed Auto Sb gf Auto Cool So pf Auto Low Hyg Med Saal High Dry SH gf Auto Fan So Low ong Med SP pf High Press the button to adjust the temperature Auto You can adjust the desired temperature by 1 C within the range of 16 C 30 C Cool You can adjust the desired temperature by 1 C within the range of 16 C 30 C Dry You can adjust the desired t
14. be disassembled in conditions of complete safety either for people or things For this reason where it is not observed as indicated into the Installation Manual the cost necessary to reach and repair the unit in safety as required by current regulations in force with slings trucks scaffolding or any other means of elevation won t be considered in warranty and charged to end user Power supply line fuse or circuit breaker b Always make sure that the power supply is compliant with current safety standards Always install the air conditioner in compliance with current local safety standards D gt Always verify that a suitable grounding connection is available amp gt Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is sufficient to ensure the operation of any other domestic appliance connected to the same electric lines Always verify that the cut off and protection switches are suitably dimensioned Verify that the air conditioner is connected to the power supply in accordance with the instructions provided in the wiring diagram included in the manual gt Always verify that electric connections cable entry section of leads protections are compliant with the electric specifications and with the instructions provided in the wiring scheme Always verify that all connections comply with the standards applicable to the installation of air conditioners Choosing the in
15. condensation draining is adequate When passing the drain hose through the 65 mm hole drilled in the wall check the followings E 0 Indoor unit Drain hose The drain hose must NOT The end of the drain hose must NOT slant upwards be placed under water P 0 0 0 15cm less g Ditch The drain hose must not Keep a clearance of at least Do not place the end of the be bent 5cm between the end of the drain hose in a hollow drain hose and the ground 32 Panama IBIM 34042A EN 4 indd 32 2015 7 10 14 04 40 aaa CON NG E Drain hose installation 1 If necessary connect the 2 meter extension drain hose to the drain hose 2 Ifyou use the extension drain hose insulate the inside of the extension drain hose with a shield 3 Fit the drain hose into 1 of 2 drain hose holes then fix the end of the drain hose tightly with a clamp B Ifyou do not use the other drain hose hole block it with a rubber stopper NOTE m Z 4 When extending the Drain Hose hold the end of Drain Hose and Extended Hose 2 rotate and insert the drain hose into Extended hose for 15 20 mm Make sure the two hoses are firmly connected there is no water leakage 5 Connect the Drain Hose after using Foam Insulation to wrap the Extended Hose Then Use vinyl tape to wrap the each side of connection by 20mm 15 20 mm 20mm 20mm a x ey PASSE ce Exte
16. set time will be displayed for 3 seconds before it disappears 14 Panama_IBIM_34042A_EN 4 indd 14 2015 7 10 14 04 31 Combining On Timer and Off Timer If the air conditioner is on If the air conditioner is off Preset time on On timer is longer than Off timer Preset time on On timer is shorter than Off timer Ex On timer 3 hours Off timer 1 hour Ex On timer 3 hours Off timer 5 hours The air conditioner will operate the Off timer after The air conditioner will operate On timer after 3 hours 1 hour from the moment you have set the timer from the moment you have set the timer 3 Your air conditioner will turn on after 2 hours Your air conditioner will remain on for 2hoursandthen 5 turn off automatically On timer and Off timer setting time should be different from each other NOTE Press the Set Cancel button on the remote controller while timer combination is on Both of the On and Off timer will be canceled and the indicator will disappear Using the Smart Saver function This function will set the temperature range limit to help you save energy while the air conditioner is operating in Cool mode O o RO kr Cook 7 Cancel Press the Smart Saver button once again ga ve amp Press the Smart Saver button on the remote controller while the air conditioner is operating in Cool mode gt Smart Saver indicator and air swing indicator appears automatically on
17. the remote controller display The air flow blades move up and down gt If the current set temperature is lower than 24 C it will automatically raise to 24 C Smart Saver function is only available in Cool mode LI Ha When Smart Saver function is activated temperature range will be limited to 24C 30 C If the desired temperature is lower than 24 C turn off the Smart Saver function by pressing the Smart Saver button again Temperature Fan speed can also be adjusted see page 11 for instructions Air flow can be adjusted manually see page 12 for instructions If you press the Mode button while the Smart Saver function is on it will cancel the function Using the Quiet function 5 O NG Mode EA Cancel Press the Quiet button once again Cool l Press the Quiet button once again Fan speed remain Auto speed EL o NOTE The air conditioner has no Quiet function ST And Ka Press the Quiet button while the air conditioner is operating in Cool Heat mode Fan speed is set to Auto UI ea 15 Panama IBIM 34042A EN 4 indd 15 2015 7 10 14 04 31 RL CON UE Using the Virus Doctor function Virus Doctor henerates hydrogen H and oxygen 0 to remove a polluted substance and decomposition of such harmful particles It makes you breathe better as if you are staying around waterfalls ocean surf rivers and mountains Press the ED button on the remote controller b ai indicator wil
18. up and down Blade pin lever Air flow blade left and right Display D o m HA Timer Auto clean indicator j o Operation indicator Power l button a Remote controller receiver Panama_IBIM_34042A_EN 4 indd 7 2015 7 10 14 04 27 aaa Ca NG Checking the remote controller Point the remote controller towards the remote controller receiver of the indoor unit When you properly press the button on the remote controller you will hear beep sound from the indoor unit and a transmit indicator appears on the remote controller display I Remote controller buttons Remote controller display Set the Virus Doctonfunction on off Smart Saver Less energy usage makes your space cool between the temperature range of 24 C 30 C Power Turn on off the air conditioner Mode Set one of the 4 operating modes see pages 10 11 for instructions Quiet Turbo wine Operate in auto fan speed to cool quickly Air swing Activate Deactivate air flow blade movement automatically up and down Temp Fi nav Increase Decrease the temperature by 1 C Adjust how much air flows through the air conditioner with the 4 different fan speeds D such as Auto Low Medium High amp Temp Humi d light Cool Has no this funtion Has no this funtion good sleep Filter Reset Beep Off Display Off Auto Clean Auto clean function Dry inside of the indoor unit to get ri
19. 015 7 10 140039 saa Ca NG K When you install the unit make first refrigerant connections and then electrical connections Connect the air conditioner to grounding system before performing the electrical connection If unit is uninstalled first disconnect electrical cables then refrigerant connections A4 or 5 meter pipe is supplied with the air conditioner If the outdoor unit is more than 4 or 5 meters away from the indoor unit you must extend the cable The maximum length of the cable is 15 07 09 12 20 18 24 meters 1 Extend the assembly cable if necessary Do not connect two or more different cables to extend the length HSITDNA It may cause fire CAUTION 2 Open the front grille 3 Remove the screw securing the connector cover 4 Pass the assembly cable through the rear of the indoor unit and connect the assembly cable to terminals Refer to the picture below B Each wire is labeled with the corresponding terminal number NOTE Pass the other end of the cable through the 65mm hole in the wall Close the connector cover by tightening the screw carefully Close the front grille Remove the terminal board cover on the side of the outdoor unit Connect the cables to the terminals as seen in the picture ON QO ur Each wire is labeled with the corresponding terminal number NOTE Indoor unit AQ09 12 18 Indoor unit Ni 1 2 3
20. 04 41 Make sure to check for gas leaks before completing the installation process connecting the assembly pipe and hose between indoor unit and outdoor unit insulating the cables hose and pipe and fixing the indoor unit to the installation plate Test part for outdoor unit Test part for indoor unit Tightening torque for body cap gt Before inspecting the leakage use a torque wrench Refer to the table to close the cap for the service valve Comply with a tightening torque for each size of the diameter and tighten the cap firmly to prevent any leakage gt To check for any possible leakage insert inert gas into Spindle the pipes connected to indoor outdoor units and I f ph check the connection part of the indoor outdoor units Charging core k i with soap lather or liquid for leakage test Tightening torque Outer Diam eter mm Body cap Nem big nln a R 22 Diameter of the screw 7 16 20UNF R 410A Diameter of the screw 1 2 20UNF 06 35 2025 09 52 20 25 Tightenina t PAT KI f 612 70 25 30 ightening torque for charging port cap Refer to the table 015 88 30 35 919 05 35 40 1 Nem 10 kgf cm To check for gas leaks on the outdoor unit Check the valve A and B using a leak detector To check for gas leaks on the indoor unit Check the flare nut C and D u
21. 67 800 0101 www samsung com latin support Spanish PUERTO RICO 1 800 682 3180 www samsung com latin_en support Engli www samsung conv latin support Spanish www samsung com latin_en support Engli TRINIDAD amp TOBAGO 1 800 SAMSUNG 726 7864 www samsung comv latin support Spanish www samsung com latin en support Engli VENEZUELA 0 800 SAMSUNG 726 7864 www samsung com ve support COLOMBIA Bogota 600 12 72 Gratis desde cualquier parte del pais 01 8000 1121120 desde su celular SAM 726 www samsung com co suppor CHILE 800 SAMSUNG 726 7864 HHP 02 24828200 www samsung com cl support BOLIVIA 800 10 7260 HHP 4828210 www samsung com cl support PERU 0800 777 08 www samsung com pe support ARGENTINE 0800 555 SAMSUNG 0800 555 7267 www samsung com ar support URUGUAY 000 405 437 33 www samsung com latin support Spanish www samsung com latin_en support English PARAGUAY 009 800 542 0001 Panama IBIM 34042A EN 4 indd 40 www samsung com latin support Spanish www samsung com latin_en support English 2015 7 10 14 04 42 100 AQO9T Series AQ12T Series AQ18T Series AQ24T Series AQO9U Series AQ12U Series AQ18U Series AQ24U Series ASO9T Series AS12T Series AS18T Series AS24T Series ASO9U Series AS12U Series AS18U Series AS24U Se
22. IM_34042A_EN 4 indd 39 Incomplete wire connections can cause electric shock or a fire AJ 39 2015 7 10 14 04 42 QUESTIONS OR COMMENTS COUNTRY CALL OR VISIT US ONLINE AT MEXICO 01 800 SAMSUNG 726 7864 www samsung com mx support BRAZIL COSTA RICA 0800 124 421 Demais cidades e regides 4004 0000 Capitais e grandes centros 0 800 507 7267 00 800 1 SAMSUNG 726 7864 www samsung com br support o in support Spani in en support Engli www samsung com l www samsung com a DOMINICAN REPUBLIC 1 800 751 2676 www samsung com www samsung com in support Spanish in_en support Engli ZSE ECUADOR 1 800 10 7267 1 800 SAMSUNG 72 6786 av www samsung com www samsung com in support Spanish in en support Engli 2 EL SALVADOR 800 6225 800 0726 7864 in support Spanish in_er support Engli www samsung com l www samsung com 25 GUATEMALA 1 800 299 0013 1 800 299 0033 in support Spanish in_en support Engli www samsung conv l www samsung com o HONDURAS 800 2791 9267 800 2791 9111 SE www samsung com www samsung com in support Spanish in en support Engli o JAMAICA 1 800 234 7267 1 800 SAMSUNG 726 7864 www samsung convlatin en support Engli NICARAGUA 001 800 5077267 www samsung com latin support Spanish www samsung comvlatin en support Engli PANAMA 800 72
23. Indoor unit amp 888 S S N O Ground wire Can Green Yellow round wire G z BO 2 Green Yellow Outdoor unit 918818 AE Outdoor unit Nol 1 2 3 Ground wire Green Yellow indoor unit AS09 12 18 AS24 Indoorunit Q18 Indoor unit S NG 1 N Ng Q Sc Ground wire I T E Green Yellow 4 Grounduire Ground ik ee round wire NU 4 ale Green Yellow Green Yellow 3 Outdoor unit Green Yellow Outdoor unit End of the wire must be circular After connecting the cables make sure terminal numbers on the indoor outdoor unit matches CAUTION Screws on terminal block must not be unscrewed with the torque less than 12kgf cm 10 Connect the grounding conductor to the grounding terminals 11 Close the terminal board cover by tightening the screw carefully In Russia and Europe consult with the supply authority to determine the supply system impedance before NOTE installation Connect the wires firmly so that wires can not be pulled out easily A If they are loose it could cause burn out of the wires WARNING Connect the wires according to color codes referring to the wiring diagram The power cable and the interconnecti
24. Rubber Legs 4 Pipe Clamps A 3 Pipe Clamps B 3 Cement Nails 6 Screws 6 length 2m 1 Putty 100g 1 Q Q Q a aG Q Co Foam Insulation 1 KING B If these accessories are supplied they will be in the accessory box NOTE I Tools required for installation General Tools Vacuum Pump Backward flowing prevention Manifold Gauge Stud Finder Torque Wrench Pipe Cutter Reamer Pipe Bender e Spirit Level Screw Driver Spanner Drill e LWrench Measuring Tape Tools for test operations Thermometer Resistance Meter Electroscope Fixing the installation plate You can select the direction of the drain hose depending on where you want to install the indoor unit Therefore before fixing the installation plate to a wall or a window frame you must determine the position of the 65mm hole through which the cable pipe and hose pass to connect the indoor unit to the outdoor unit When facing the wall the pipe and cable can be connected from the Right A Left B Underside_right C Rear right or left D 1 Determine the position of the pipe and drain hose hole as seen in the picture and drill the hole with an inner diameter of 65mm so that it slants slightly downwards Unit mm Model A BC D X 09 12XX 27 120 68 27 A Make sure to drill only one 186 27 190 68 27 ES holeafter choosing the XX24XX 34 140 68
25. able Interconnection cable Type GL 2 ye 09 124 3G 1 0mm HO7RN F a a 20A ET oarsman Seam F ka 2 LI KR mac 3625m Fam Connect the power cable to the auxiliary circuit breaker If every pole fails to connect to the power supply it must be incorporated in a wire with a contact opening of 33mm I Connecting the cable Electrical work 1 For electrical and earth works comply with the technical standards of electrical installations and the the wiring regulations of the Electricity Enterprises Act 2 Tighten the terminal block screw to 1 2 1 8 Nem 12 18 kgf cm 3 Precautions when connecting terminal blocks of the indoor unit gt Before connecting make sure the connecting part of the terminal socket is facing upwards g Ho The terminal socket There is no ring terminal is damaged to cover the wire Upside down gt There must be no space between the terminal and the screw when connected Any remaining space may become a fire hazard due to overheating of the electrical contact The terminal socket Either the screw is not fitted properly is upside down or there is a space between the screw and the ring terminal For the terminal block wiring use a wire with a ring terminal socket only CAUTION Regular wires without a ring terminal socket may become a fire hazard due to overheating of the electrical contact during a wiring work 28 Panama_IBIM_34042A_EN 4 indd 28 2
26. be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry Do not use the units if damaged If problems occur switch the unit off and disconnect it from the power supply In order to prevent electric shocks fires or injuries always stop the unit disable the protection switch and contact SAMSUNG technical support if the unit produces smoke if the power cable is hot or damaged or if the unit is very noisy Always remember to inspect the unit electric connections refrigerant tubes and protections regularly These operations should be performed by qualified personnel only The unit contains moving parts which should always be kept out of the reach of children Do not attempt to repair move alter or reinstall the unit If performed by unauthorized personnel these operations may cause electric shocks or fires Do not place containers with liquids or other objects on the unit All the materials used for the manufacture and packaging of the air conditioner are recyclable The packing material and exhaust batteries of the remote controller optional must be disposed of in accordance with current laws The air conditioner contains a refrigerant that has to be disposed of as special waste At the end of its life cycle the air conditioner must be disposed of in authorized centers or returned to the retailer so that it can be disposed of correctly and safely
27. can not access vvvvvvvvvvy Avoid the following places to prevent malfunction of the unit cauron Where there is machine oil Salty environment such as seaside areas Where sulfide gas exists Other special atmosphere areas Observe the clearances and maximum lengths as seen in the picture below when installing the air conditioner gt 125mm Or more 3 You can select the direction of draining left or right Wrap the refrigerant pipes and the drain hose with the absorbent pad and vinyl tape Refer to pagel37 for further details L m as maximum pipe length and 3 m as minimum pipe length CAUTION It will reduce noise and vibration H meters maximum total GL meters maximum pipe length total pipe length Model LH XXK09 12 18XX 15 7 XXK24XKXK 20 8 24 Panama IBIM 34042A EN 4 indd 24 2015 7 10 16 18 30 Space Requirements for Outdoor Unit When installing 1 outdoor unit Figure Description Top view Air intake Air Air outlet _ e Air flow direction When the air outlet is opposite the wall LLL NG o _ e A pa of fa a D The upper part of the outdoor unit and the air outlet is towards the wall g 2000 or more 5 G When installing more than 1 outdoor unit When the air outlet is towards the wall Panama IBIM 34042A EN 4 indd 25 m zZz O Side v
28. conditioner will return to previous status Check Off timer indicator and 2 indicator on the indoor unit Cancel Press the Set Cancel button once again Temp You can set the desired temperature by 1 C in the range of 16 C 30 C Fan speed will be adjusted automatically according to the good sleep Ss mode E Air flow direction will be adjusted automatically according to the good sleep mode Temperature and fan speed changes in good sleep mode Fall asleep Eases you into sleep by dropping the temperature Sound sleep Relaxes your body and raises your temperature slightly Wake up from good sleep mode Allows you to wake up from comfortable intermittent air and it makes you feel refreshed Set Off timer in good sleep mode over 5 hours You fell disturbed sleep if the good sleep is set too short or long note because the default is set to 8 hour operation Ifthe good sleep mode is set less than 4 hours the operation will stop at the same time If the good sleep mode is set over 5 hours it will run as Wake up stage from the last one hour before it stops Recommended set temperature is between 25 C 27 C for cooling 13 Panama IBIM 34042A EN 4 indd 13 2015 7 10 14 04 30 Setting the On Off timer You can set the air conditioner to turn on off automatically at desired time Setting On timer while the air conditioner is off Off timer while the air conditioner is
29. cts or devices under the indoor unit b Water dripping from the indoor unit may result in fire or property damage Check that the installation frame of the outdoor unit is not broken at least once a year gt Failing to do so may result in injury death or property damage Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Do not stand on top of the appliance or place objects such as laundry lighted candles lighted cigarettes dishes chemicals metal objects etc on the appliance gt This may result in electric shock fire problems with the product or injury Do not operate the appliance with wet hands gt This may result in electric shock Do not spray volatile material such as insecticide onto the surface of the appliance gt As well as being harmful to humans it may also result in electric shock fire or problems with the product Do not drink the water from the air conditioner gt The water may be harmful to humans Do not apply a strong impact to the remote controller and do not disassemble the remote controller Do not touch the pipes connected with the product gt This may result in burns or injury Do not use this air conditioner to preserve precision equipment food animals plants or cosmetics or for any other unusual purposes gt This may result in property damage Avoid directly exposing humans animals or plants from t
30. d be inside the indoor unit 1 Unscrew the caps at the end of each pipe D All inert gas exhausts from the indoor unit HSITDNA To prevent dirt or foreign substances from getting into the pipes during note installation do NOT remove the caps completely until you are ready to connect the pipes Di LI Dee TIYA The remaining air in the Refrigeration cycle which contains moisture cauron May cause malfunction on the compressor as Always contact the service center or a professional installation agency for product installation Pipes Unscrew the caps Cutting or extending the pipe The length of the pipe can be Extended up to see table page 24 Shorten up to see page 24 If you need a pipe longer than 4 or 5 meters caution YOU must extend the assembly cable You must add refrigerant to the pipes otherwise the indoor unit may freeze 1 Make sure that you have all the required tools pipe cutter reamer flaring tool and pipe holder 2 Ifyou want to shorten the pipe cut it using a pipe cutter ensuring that the cut edge remains at 90 with the side of the pipe see below examples of correct and incorrect cut edges Pipe cutter ay Oblique Rough Burr ba K bi 3 To prevent a gas leak remove all burrs at the cut edge of the pipe using a reamer A Face the pipe down while removing the burrs to make sure that burrs do not get in to the pipe CAUTION
31. d of odor good sleep Set the good sleep mode on On Timer Set Cancel Set the On Timer on Cancel the timer good sleep mode Off Timer 204 Switch the function of the button on the remote controller Set the Off Timer on SAMSUNG Filter Reset Reset the Filter Clean reminder Beep off To silence the beep sound when pressing the button Display off Has no this function When you press 2 F button the indicator will be displayed on the remote controller and you can change the functions on the remote controller as listed below Auto Clean gt Filter Reset Temp Humi Beep Off good sleep Display Off function If you select the function under the button while the function of the button is switched by 2 F button the 2 F function is canceled 8 Panama IBIM 34042A EN 4 indd 8 2015 7 10 14 04 27 aaa CON NG I Remote controller display Quiet indicator Turbo indicator ce HA Operation mode indicator Smart Saver indicator Low battery indicator d light Cool indicator rt mo Transmit indicator HSITDNA Air swing indicator Fan speed indicator of all Auto Turbo 2 F indicator Set temperature indicator On Timer indicator 7 Off Timer indicator L AL Ka Medium good sleep indicador Spa High x As to AS gt K gt K gt k Series don t operate the air conditioner when the remote controller is set to Heat mode Heat mode can be selected AQ 7k Series Bat
32. e better as if you are staying around waterfalls ocean surf rivers and mountains Panama IBIM 34042A EN 4 indd 2 Safety PrecAULIONS A kinikimkim Checking before use Checking the name of the parts Checking the remote controller Basic FUNCTION unan Adjusting the air flow direction Using the Turbo function good sleep mode Setting the On Off timer Using the Smart Saver function Using thdVirus Doctorfunction ma Using the Auto Clean function Cleaning the air conditioner Maintaining the air conditioner Troubleshooting INSTALLATION PARTS Safety precautions Choosing the installation location ACCESSONES sisii Fixing the installation plate Connecting the assembly cable ul aman 28 nstalling and connecting the assembly pipe of the indoor unit Purging the indoor unit Cutting or extending the pipe nstalling and connecting the drain hose of the indoor unit 32 Changing direction of the drain hose esses 33 nstalling and connecting the drain hose of the outdoor unit Purging the connected pipes Performing the gas leak tests Fixing the indoor unit in place Fixing the outdoor unit in place Final check and trial operation Pump down procedure when removing the product nn 38 How to connect your extended power cables 39 2015 7 10 14 04 26 USING PARTS Safety precautions Before using your new air conditioner please read this manual
33. emperature by 1 C within the range of 18 C 30 C Fan Temperature adjustment is not possible gt i Airflow can be adjusted manually see page 12 for instructions 11 Panama IBIM 34042A EN 4 indd 11 2015 7 10 14 04 29 aaa a NG Adjusting the air flow direction Air flow can be directed to your desired position I Vertical air flow Air flow blades move up and down Press the Air swing button on the remote controller gt Air swing indicator will be on and air flow blades move up and down continuously to circulate the air gt Press the Air swing button on the remote controller again to keep the air flow direction in a constant position Auto sr E LI Bon I Horizontal air flow Make sure one of the blade pin lever that stick out of the air flow blades are not broken A Move the blade pin lever left or right to keep the air flow direction in a constant D position you prefer amp Be extremely careful with your fingers while adjusting the Horizontal air flow direction There is a potential risk of personal injury when the unit is mishandled Using the Turbo function Turbo function will be helpful to cool your room quickly and effectively Press the Turbo button on the remote controller during Cool mode gt Turbo indicator appears on the remote controller display and the air conditioner operates in Turbo function for 30 minutes
34. f the drained water Make sure the indoor unit is in upright position when you pour water to check for leakage Make sure that the water does not overflow onto the electrical part CAUTION 33 Panama IBIM 34042A EN 4 indd 33 2015 7 10 14 04 41 Panama IBIM 34042A EN 4 indd 34 2015 7 10 14 04 41 Installing and connecting the drain hose of the outdoor unit AQ gt k series While heating ice may accumulate During the process of defrosting check if condensation draining is adequate For adequate draining do the following 1 Insert the drain plug into the drain hole on the underside of the outdoor unit To avoid drain plug from contacting the ground secure gap between the ground and the bottom surface of the outdoor unit 2 Drain hole Ew Drain plug CAUTION 2 Connect a drain hose to the drain plug Bottom surface of outdoor aka Drain hole Drain plug Drain hose AN Snow proof hood 3 Ensure that condensation draining is adequate In areas with heavy snow fall piled snow could block the air intake To avoid this incident install a frame that is higher than estimated snow fall In addition install a snow proof hood to avoid snow from piling on the outdoor unit Estimated snow fall Ground Purging the connected pipes The outdoor unit is loaded with sufficient R22 refrigerant You should purge the air in the indoor unit and in the p
35. he air flow from the air conditioner for long periods of time gt This may result in harm to humans animals or plants This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance FOR CLEANING A WARNING O Do not clean the appliance by spraying water directly onto it Do not use benzene thinner or alcohol to clean the appliance gt This may result in discoloration deformation damage electric shock or fire Before cleaning or performing maintenance unplug the air conditioner from the wall socket and wait until the fan stops gt Failing to do so may result in electric shock or fire FOR CLEANING A CAUTION O O Take care when cleaning the surface of the heat exchanger of the outdoor unit since it has sharp edges gt To avoid cutting your fingers wear thick cotton gloves when cleaning it Do not clean the inside of the air conditioner by yourself gt For cleaning inside the appliance contact your nearest service center gt When cleaning the internal filter refer to the descriptions in the Cleaning the air conditioner section gt Failure to do may result in damage electric shock or fire Pana
36. he following accessories are supplied with the air conditioner The number of each accessory is indicated in parentheses NOTE I Accessories in the indoor unit case Installation Plate 1 Remote Batteries for User s amp Installation controller 1 Remote controller 2 Manual 1 ES 77 I Accessories in the outdoor unit case 5 wire 3 wire A Assembly Cable 1 Assembly Cable 1 Tap n yeas 1 Pata de hule 4 AQ ASXX 4 amp The flare nuts are attached to the end of each pipe of an evaporator or a service port Note Use the nuts when connecting the pipes A S W The 5 AQ 3 ASXXK wire assembly cable is optional If it is not supplied use the standard cable The drain plug and rubber leg are only included when the air conditioner is supplied without the assembly pipe as seen in the picture below 26 Panama_IBIM_34042A_EN 4 indd 26 2015 7 10 140436 I Optional accessories The following connection accessories are optional If they are not supplied you should obtain them before installing the air conditioner Insulated Insulated Assembly Insulated Assembly Pipe Insulated Assembly Pipe PET3 Foam Tube l Drain Plug 1 Assembly Pipe Pipe 9 52mm 1 012 70mm 1 015 88mm 1 insulation 1 Vinyl Tapes 2 AOKKX 06 35mm 1 09 XX12 18X XX24XX 2 oo a as A M4 x 25 Tapped Drain Hose
37. he following chart if the air conditioner operates abnormally This may save time and unnecessary expenses PROBLEM SOLUTION The air conditioner does Check power status and then operate the air conditioner again not work at all Plugin or switch on the circuit breaker and then operate the air conditioner again Check if you have set the Off Timer Operate the air conditioner again by pressing the Power button The temperature Check if you have selected Fan Turbo mode In these modes desired temperature is set to adjustment is not working auto and you cannot adjust the temperature Cool Warm air does not come out of the air conditioner Check if the set temperature is higher during Cool mode than the current temperature Press the Temp or button on the remote controller to change the set temperature Check if the Air filter is blocked by dirt If there is a lot of dust on the Air filter cooling performance may decrease Clean them frequently Check if the outdoor unit is covered or installed near the obstacle Take the cover off and take the obstacle away If you want to operate the air conditioner in the sunlight cover the outdoor unit using curtains or etc Check if the air conditioner is operating in De ice mode When the ice formed in winter or the outdoor temperature is too low the air conditioner operates in De ice mode automatically In De ice mode indoor fan stops and cool air does not come out
38. iew z T outlet 4 Air intake Unit mm When the air outlet is towards the When 3 sides of the outdoor unit are wall blocked by the wall o w CJ HE ii NP y 8 o LE y ia 150 or more 600 or more The upper part of the outdoor unit When the walls are blocking front amp and the air outlet is opposite the and the rear side of the outdoor unit wall v LLLEILIPL LT A E rs 2 al B U By 188 Unit mm When 3 sides of the outdoor unit are blocked by the wall g 2 8 o o o 5 o i HOTTE o 3 U gt pag ta kag lt 300 or more 600 ormore 6000rmore 600 or more 25 2015 7 10 14 04 35 aaa Cia NG Choosing the installation location FE When the walls are blocking front and the rear side of the outdoor When the upper part of the outdoor unit and units the air outlet is opposite the wall 300 or more KOI MOIE U U o Len en CAR U 600 or more 300 or more 500 or more 1500 or more 600 or more a When front and rear side of the outdoor unit is towards the wall UP of pain Jk Jk 300 or more UE 500 or more 1500 or 600 or 3000 or 3000 or 200 or more more more more more Ifinstallation is done in inappropriate space unit may generate sound and cause bad effect on the product caution Installation must be done in level and in a place where vibration will not cause any effect Accessories T
39. in components 2 Before using the air conditioner again dry the inner components of the air conditioner again by running in Fan mode for 3 to 4 hours This helps remove odors which may have generated from dampness Periodical checks Refer to the following chart to maintain the air conditioner properly HSITDNA Type Description nada Ena Eun Oncea year Clean the air filter 1 Indoor Clean the condensate drain pan 2 e unit Clean the condensate drain pipe 2 Replace the remote controller batteries 1 Clean the heat exchanger on the outside of the unit 2 Clean the heat exchanger on the inside ofthe unit 2 amp Clean the electric components with jets of air 2 Outdoor Verify that all the electric components are firmly e unit tightened 2 Clean the fan 2 Verify that all the fan assembly is firmly tightened 2 Clean the condensate drain pan 2 This check mark requires checking the indoor outdoor unit periodically following to the description to maintain the air conditioner properly 1 The described operations should be performed more frequently if the area of installation is very dusty NOTE 2 These operations must always be performed by qualified personnel For more detailed information see the installation part in the manual Panama IBIM 34042A EN 4 indd 19 19 2015 7 10 14 04 34 Troubleshooting Refer to t
40. ipe lf air remains in the refrigerant pipes it affects the compressor It may cause reduction of cooling capacity and malfunction When installing make sure there is no leakage When recovering the refrigerant ground the compressor first before removing the connection pipe If the refrigerant pipe is not properly connected and the compressor works with the service valve open the pipe inhales the air and it makes the pressure inside of the refrigerant cycle abnormally high It may cause explosion and injury 1 Connect each assembly pipe to the appropriate valve on the outdoor unit and Outdoor unit 4 Indoor unit tighten the flare nut Gas pipe side 2 Tighten the flare nut first with your hands and then with a torque wrench Liquid pipe side applying the following torque PA 34 B Excessive torque can be cause of gas leakage NOTE Make the electrical connection and leave the system into stand by mode Do not turn on the system This is necessary for better vacuum operation full OPEN position of Electronic Expansion Valve EEV 3 Connect the charging hose of the low pressure side of manifold gauge toa gas service port as seen in the picture 4 Open the valve of the low pressure side of manifold gauge counterclockwise 5 Purge the air in the connected pipes using the vacuum pump for about 15 minutes gt Make sure that pressure gauge shows 0 1MPa 76cmHg
41. l appears on the remote controller display and the air conditioner button once again Cancel Pressthe The Se function can be selected whether the air conditioner is on off NOTE Using the Auto Clean function D Auto clean function will prevent from growing mold by eliminating the moisture inside of the indoor unit Your indoor unit amp evaporates the moisture inside of the unit Activate this function to provide you with more clean and healthier air Press the Auto Clean button When the air conditioner is turned off Auto Temp good Clear Humi sleep Filter eep Off Display Off On Off se Timer Timer Cancel gt The Auto clean indicator on the indoor unit display appears and the Auto cleaning function runs When the air conditioner is turned on b After stopping the air conditioner operation the Auto clean indicator on the indoor unit display appears and the Auto cleaning function runs X Auto Cleaning time can vary depending on the previously used mode Auto cool Cool Dry mode approximately 30 minutes Fan mode approximately 15 minutes Cancel Press the Auto Clean button once again When the air conditioner is turned on the Auto clean function runs after Note stopping the air conditioner operation 16 Panama IBIM 34042A EN 4 indd 16 2015 7 10 15 40 46 Cleaning the air conditioner Make sure the power is turned off and u
42. lectric leakage Install your appliance on a level and hard floor that can support its weight gt Failing to do so may result in abnormal vibrations noise or problems with the product Install the draining hose properly so that water is drained correctly gt Failing to do so may result in water overflowing and property damage When installing the outdoor unit make sure to connect the draining hose so that draining is performed correctly gt The water generated during the heating operation by the outdoor unit may overflow and result in property damage In particular in winter if a block of ice falls it may result in injury death or property damage Panama_IBIM_34042A_EN 4 indd 3 2015 7 10 14 04 26 Safety precautions FOR POWER SUPPLY WARNING Q Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis gt Unplug the power plug and clean it with a dry cloth gt Failing to do so may result in electric shock or fire Plug the power plug into the wall socket in the right direction so that the cord runs towards the floor gt Ifyou plug the power plug into the socket in the opposite direction the electric wires within the cable may be damaged and his may result in electric shock or fire When the appliance or power plug or power cord is damaged contact your nearest service center Plug the power plug into the wall socket firmly
43. ma_IBIM_34042A_EN 4 indd 5 2015 7 10 14 04 26 aaa NG Checking before use I Operation ranges The table below indicates the temperature and humidity ranges the air conditioner can be operated within Refer to the table for efficient use Mode loss Quan Indoor humidity Remark temperature perature Cooling 16 C 32 C 15 C 43 C Relative humidity 80 or less Dry 18 C 32 C 15 C 43 C gt If the air conditioner operates in cooling mode for long period of time in high humidity area dew may be formed I Maintaining your air conditioner Internal protections via the unit control system gt This internal protection operates if an internal fault occurs in the air conditioner Type Description Anti protection of The compressor will be off to protect internal battery when the air conditioner operates internal battery in Cool mode The air conditioner does not start operating immediately to protect the compressor of Protect compressor P the outdoor unit after it has been started 6 Panama IBIM 34042A EN 4 indd 6 2015 7 10 14 04 26 aaa CON NG Checking the name of the parts Your air conditioner may slightly look different from illustration shown above depending on your model Main parts HSITDNA Room temperature sensor nan Air filter under the panel Air flow blade
44. nplugged from caution the wall socket when cleaning the air conditioner I Cleaning the indoor unit gt Wipe the surface of the unit with a slightly wet or dry cloth when needed Contact the service center when you clean the indoor unit Note heat exchanger because it needs to be disassembled Do not clean the display using alkaline detergent caution Do not use sulfuric acid hydrochloric acid organic solvents such as thinner kerosene and acetone etc to clean the surface of the product or put any stickers on it They may damage the surface of the air conditioner I Cleaning the outdoor unit heat exchanger gt When dust accumulates on the heat exchanger it may decrease cooling performance Therefore clean it regularly b Spray water to clean the dust If it is difficult to clean the outdoor unit heat exchanger on NOTE your own contact service center Be careful with the sharp edges on the outdoor unit heat canon EXChanger I Opening the panel Tightly grab top of the front panel and pull it down to open Then slightly lift the panel up Panama IBIM 34042A EN 4 indd 17 HSITDNA RES RON RE ententes SR RCE x RY IG 2 g w bat ava NG NG Serene tatag 2S NG Re ES 3 3 RES TE ROO LR KAAS RE KS Ng NG Q Heat exchanger Illustration may differ slightly depending on the models 17 2015 7 10 14 04 33 MEMES
45. nsion rain hose Drain hose drain hose Vinyl Tape Foam Insulation 6 Pass the drain hose under the refrigerant pipe keeping the drain hoseti Shield ose tight gt 7 Pass the drain hose through the hole in the wall Check if it slants gt Bana ATAT aa a downwards as seenin the picture Tai a TT 8 Using natural drainage method check the drainage is normal Drain hose Extension drain hose B The hose will be fixed permanently into position after finishing the installation and the gas leak test refer to page 37 38 for further details Make sure the installed direction of the drain hose is correct Inadequate installation may cause condensate water leakage If the drain hose is routed inside the room insulate the hose so that dripping condensation does not damage the furniture or floors DO NOT WALL UP THE DRAIN HOSE CONNECTION Drain hose connection must be easy accessible and serviceable Changing direction of the drain hose Change the direction only when it is necessary 1 Detach the rubber cap with the plier Screw hole 2 Detach the drain hose by pulling it and turning to the left 3 Insert the drain hose by fixing it with the screw into the groove of the drain hose and the outlet of the drain pan 4 Attach the rubber cap with a screwdriver by turning it to the right until it fixes to the end of the groove 5 Check for leakage on both side of the drain outlet Pour the water in direction of arrow Direction o
46. o an appropriate support wall or ground Y mm B REE la p i Rubber 1 Place the outdoor unit as indicated on the top of the unit to let the discharged air PG out properly Model x Y 2 Fixthe outdoor unit in level to an appropriate support using anchor bolts AQ AS 09 12 457 254 ia ia x AQI8 543 319 3 If the outdoor unit is exposed to strong winds install shield plates around the ASI8XX 538 290 outdoor unit so that the fan can operate correctly AQ AS24X X 543 319 B Secure the rubber leg to prevent the generation of noise and vibration NOTE I Outdoor unit installed on the wall by rack Ensure the wall will be able to suspend the weight of rack and outdoor unit Install the rack close to the column as much as possible Install proper grommet in order to reduce noise and residual vibration transferred by outdoor unit towards wall Soft rubber designed to cut off vibration from rack to wall not supplied with product S 37 Panama_IBIM_34042A_EN 4 indd 37 2015 7 10 14 04 42 Final Check and Trial Operation To complete the installation perform the following checks and tests to ensure that the air conditioner operates correctly Check the followings Strength of the installation site Tightness of pipe connection to detect gas leak Electric wiring connection Heat resistant insulation of the pipe
47. on 1 Press the On Timer Off Timer button Setting On timer gt On Off timer indicator will blink on the remote controller display Temp d pur pur E re E re Filter Reset Beep Off Display Off On off S Timer yimer Cancel 2 Press the On Timer Off Timer button to set the time gt You can set the time in half hourly unit from 30 minutes 3 hours and hour unit from 3 hours 24 hours gt Operating hour can be set from minimum 30 minutes to maximum 24 hours 3 Press the Set Cancel button to active it on gt On timer indicator stops blinking and reserved time will be displayed for 3 seconds gt Ifyou don t press Set Cancel button within 10 seconds after selecting the time the air conditioner will return to previous status Check On timer or Off timer indicator and 3 indicator on the indoor unit Setting Off timer Cancel Press the Set Cancel button Additional options available in On timer mode 7 C You can select from Auto Cool Dry Fan mode Na Tem ead Fan You can adjust the fan speed in Cool Fan mode Clean Humi sleep Er Filter Reset Beep Off Display Off on of Set Timer Bi Wee Temp You can adjust the temperature in Auto Cool Dry mode Auto Only the latest setting timer will be applied between the On Timer Off Timer ET yy Note and good sleep Off timer functions After setting the timer the
48. on cable should be selected according to the specification in page 28 29 Panama_IBIM_34042A_EN 4 indd 29 2015 7 10 140439 Installing and connecting the assembly pipe of the indoor unit Connect indoor and outdoor units with field supplied copper pipes by means of flare connections Use insulated seamless refrigeration grade pipe only Cu DHP type according to 1501337 degreased and deoxidized suitable for operating pressures of at least 4200 kPa and for burst pressure of at least 20700 kPa Under no circumstances must sanitary type copper pipe be used There are 2 refrigerant pipes of different diameters A short pipe is already fitted to the air conditioner You may need to extend the pipe using the assembly pipe optional doon The smaller one is for the liquid refrigerant The larger one is for the gas refrigerant DA FH The connection procedure for the refrigerant pipe varies UNE according to the exit position of the pipe when facing the wall j h A Right A GQ Left B pgs Underside C Rear Torque Cut out the appropriate knock out piece A B C on the rear of the indoor Outer Diameter Nem kgf cm nit unless you connect the pipe directly from the rear a PIPES 06 35 mm 14 18 140 180 Smooth the cut edges 69 52 mm 34 42 350 430 912 70 mm Remove the protection caps of the pipes and c
49. onnect the assembly pipe 49 61 500 620 to each pipe Tighten the nuts first with your hands and then with a 915 88 mm 68 82 690 830 torque wrench applying the following torque B Ifyou want to shorten or extend the pipes refer to page 31 32 NOTE 4 5 6 7 For further details on how to connect to the outdoor unit and purge the air refer to page 34 35 30 Cut off the remaining foam insulation If necessary bend the pipe to fit along the bottom of the indoor unit Then pull it out through the appropriate hole b The pipe should not project from the rear of the indoor unit b The bending radius should be 100 mm or more Pass the pipe through the hole in the wall The pipe will be insulated and fixed permanently into position after finishing the installation and the gas leak test note referto pagg 37 or further details Tighten the flare nut with torque wrench according to specified method caution lftheflare nut is over tightened the flare may break and cause refrigerant gas leakage DO NOT WALL UP THE PIPE CONNECTION All refrigerant pipe connection must be easy accessible and serviceable Panama_IBIM_34042A_EN 4 indd 30 2015 7 10 16 12 52 Purging the indoor unit The indoor unit is supplied with inert gas nitrogen Before installing the unit check if nitrogen gas flow out of indoor unit If this one isn t true DO NOT INSTALL THE UNIT since leakage coul
50. product Do not touch the air flow blade with your hands or fingers during the heating operation gt This may result in electric shock or burns Do not insert your fingers or foreign substances into the air inlet outlet of the air conditioner gt Take special care that children do not injure themselves by inserting their fingers into the product Do not strike or pull the air conditioner with excessive force gt This may result in fire injury or problems with the product FOR USING WARNING O Do not place an object near the outdoor unit that allows children to climb onto the machine gt This may result in children seriously injuring themselves Do not use this air conditioner for long periods of time in badly ventilated locations or near infirm people gt Since this may be dangerous due to a lack of oxygen Open a window at least once an hour If any foreign substance such as water has entered the appliance cut the power by unplugging the power plug and turning the circuit breaker off and then contact your nearest service center gt Failing to do so may result in electric shock or fire HSITDNA Do not attempt to repair disassemble or modify the appliance yourself gt Do not use any fuse such as cooper steel wire etc other than the standard fuse gt Failing to do so may result in electric shock fire problems with the product or injury FOR USING A cauTION O Do not place obje
51. ries Recycled Paper imagine the possibilities Thank you for purchasing this Samsung product ean 2015 7 10 14 04 43 EN ES FT DB98 3 Panama IBIM 34042A EN 4 indd 41
52. rvice company gt Failing to do so may result in electric shock fire explosion problems with the product or injury Install a switch and circuit breaker dedicated to the air conditioner gt Failing to do so may result in electric shock or fire Fix the outdoor unit firmly so that the electric part of the outdoor unit is not exposed gt Failing to do so may result in electric shock or fire O Do not install this appliance near a heater inflammable material Do not install this appliance in a humid oily or dusty location in a location exposed to direct sunlight and water rain drops Do not install this appliance in a location where gas may leak gt This may result in electric shock or fire Never install the outdoor unit in a location such as on a high external wall where it could fall gt Ifthe outdoor unit falls it may result in injury death or property damage This appliance must be properly grounded Do not ground the appliance to a gas pipe plastic water pipe or telephone line gt Failure to do so may result in electric shock fire an explosion or other problems with the product gt Never plug the power cord into a socket that is not grounded correctly and make sure that it is in accordance with local and national codes FOR INSTALLATION A caution O This appliance should be positioned in such a way that it is accessible to the power plug gt Failing to do so may result in electric shock or fire due to e
53. servicing it or accessing its internal components Verify that installation and testing operations are performed by qualified personnel Verify that the air conditioner is not installed in an easily accessible area General information gt v v 22 Carefully read the content of this manual before installing the air conditioner and store the manual in a safe place in order to be able to use it as reference after installation For maximum safety installers should always carefully read the following warnings Store the operation and installation manual in a safe location and remember to hand it over to the new owner if the air conditioner is sold or transferred This manual explains how to install an indoor unit with a split system with two SAMSUNG units The use of other types of units with different control systems may damage the units and invalidate the warranty The manufacturer shall not be responsible for damages arising from the use of non compliant units The air conditioner is compliant with the requirements of the Low Voltage Directive 72 23 EEC the EMC Directive 89 336 EEC and the Directive on pressurized equipment 97 23 EEC The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper connection of electric and requirements set forth in the Operating limits table included in the manual shall immediately invalidate the warranty The air conditioner should
54. sing a leak detector 36 Panama IBIM 34042A EN 4 indd 36 2015 7 10 14 04 41 Fixing the indoor unit in place Perform the following work on the area where gas leak test was done priorly After checking for gas leaks in the system insulate the pipe hose and cables Insulation Then place the indoor unit on the installation plate 1 To avoid condensation problems wrap foam insulation as shown in the figure on O 69 2 a part without insulation on the end of the pipes 2 2 Wind the pipe assembly cable and drain hose with vinyl tape Pipes 3 Place the bundle the pipe assembly cable and drain hose in the lower part of the indoor unit carefully so it does not project from the rear of the indoor unit p P s g Installation 4 Hookthe indoor unit to the installation plate and move the unit to the right plate Connecting and left until it is securely in place Vinyl tape Connecting wires Make sure pipe does not move when you install the indoor unit on i i Drain hose cron aninstallation plate 5 Wrap the rest of the pipe with vinyl tape 6 Attach the pipe to the wall using clamps optional Fixing the outdoor unit in place Install the outdoor unit in level on a stable base to avoid the generation of noise and X mm Vibration especially when installing the unit close to a neighbor a a If you install the outdoor unit in a place exposed to strong winds or at a height fix it t
55. stallation location I Indoor unit b Where airflow is not blocked Where cool air can be distributed throughout the room Install the refrigerant piping length and the height difference of both indoor and outdoor units as indicated in the installation diagram Wall that prevents vibration and is strong enough to hold the product weight Out of the direct sunlight 1m or more away from the TV or radio to prevent the screen from being distorted or noise from being generated As far away as possible from the fluorescent and incandescent lights so that the remote controller can be operated well A place where the air filter can be replaced easily vv YYYY 23 Panama IBIM 34042A EN 4 indd 23 2015 7 10 14 04 34 aaa a NG Choosing the installation location I Outdoor Unit Where it is not exposed to strong wind Well ventilated and dustless places Out of the direct sunlight and rain Where neighbors are not annoyed by operation sound or hot air Solid wall or support that prevents vibration and is strong enough to hold the product weight Where there is no risk of flammable gas leakage When installing the unit at a high place be sure to fix the unit legs 3m or more away from the TV or radio to prevent the screen from being distorted or noise from being generated Install the unit horizontally Place where drained water does not become any problem Place with no plants especially climbing plants and where small animal
56. t use a ventilating fan gt Aspark may result in an explosion or fire To reinstall the air conditioner please contact your nearest service center gt Failing to do so may result in problems with the product water leakage electric shock or fire gt A delivery service for the product is not provided If you reinstall the product in another location additional construction expenses and an installation fee will be charged gt Especially when you wish to install the product in an unusual location such as in an industrial area or near the seaside where it is exposed to the salt in the air please contact your nearest service center Do not touch the power plug or the circuit breaker with wet hands gt This may result in electric shock Do not unplug the power plug or turn the air conditioner off with the circuit breaker while it is operating gt Plugging the power plug into the wall outlet or turning the air conditioner on from the circuit breaker may cause a spark and result in electric shock or fire After unpacking the air conditioner keep all packaging materials well out of the reach of children as packaging materials can be dangerous to children gt Ifa child places a bag over its head it may result in suffocation Do not insert your fingers or foreign substances into the outlet when the air conditioner is operating gt Take special care that children do not injure themselves by inserting their fingers into the
57. tery changing time When the battery is exhausted 524 will be displayed in the remote controller display When the icon appears change the batteries The remote controller requires two 1 5V AAA type batteries Storing the remote controller When you do not use the remote controller for long time remove the batteries from the remote controller and store it Inserting the batteries 1 Push the lever as arrow 2 Insert two AAA batteries 3 Close the cover by place it back to its indicates on the rear side of the Check and match the 4 and original position remote controller and pull up signs accordingly Make sure you You should hear click sound when the cover is have inserted the batteries in locked properly correct position The signal may not be received well of electronic lighting style fluorescent lamps such as inverter fluorescent lamps note arein the same space If other electrical products operate by the remote controller call your nearest contact center 9 Panama IBIM 34042A EN 4 indd 9 2015 7 10 14 04 28 Panama IBIM 34042A EN 4 indd 10 2015 7 10 14 04 28 Basic function Basic operation is an operation mode that can be selected by pressing the Mode button Auto In Auto mode the air conditioner will automatically set the temperature and fan speed depending on the room temperature detected by the room temperature Cool In Cool mode the
58. thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Because the following operating instructions cover various models the characteristics of your air conditioner may differ slightly from those described in this manual If you have any questions call your nearest contact center or find help and information online at www samsung com HSITDNA Important safety symbols and precautions A WARNING Hazards or unsafe practices that may result in severe personal injury or death A CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage ae Unplug the power plug from the O Follow directions salle her O Do NOT attempt Do NOT disassemble Make sure the machine is grounded to prevent electric shock FOR INSTALLATION WARNING Q Plug the power cord into a wall socket with the power specifications of the product or higher and use the socket for this appliance only In addition do not use an extension cord gt Sharing a wall socket with other appliances using a power strip or extending the power cord may result in electric shock or fire gt Do not use an electric transformer It may result in electric shock or fire gt Ifthe voltage frequency rated current condition is different it may cause fire The installation of this appliance must be performed by a qualified technician or se

Samsung 9.000 Btus

Contents

Download Pdf Manuals

Related Search

Related Contents