Samsung ND020VHXCA manual do usuário
Contents
1. 2 Remove the Air filter Grab the handle and lift it up Then pull the Air filter towards you and slide it down 3 Slide the Deodorizing filter color in black out to remove it from the slot E Doa Hl H 4 e Deodorizing filter be placed any 4 slots beneath the air filter Front panel of your air conditioner is actually not detachable 4 Install the new Deodorizing filter back in position 5 Close the front panel Grab the side of the front panel tightly and push it downward The replacement timing of the Deodorizing filter differs depending on usage and environmental conditions Even if Deodorizing and Anti allergy filters are installed in an inverted position it will not affect its filtration system cleaning and maintaining 31 NDODOVOOOO IB 31763 1 10 11 11 indd 31 e 2010 11 11 14 42 03 L cleaning and maintaining the air conditioner MAINTAINING YOUR AIR CONDITIONER If the air conditioner will not be used for an extended period of time dry the air conditioner to maintain it in best condition 1 Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and disconnect the power plug There may be internal damage if moisture is left in components 2 Before u2. 31763 1 10 11 11 indd 32 e 2010 11 11 14 42 03 Es HE Internal protections via the unit control system This internal protection operates if an internal fault occurs in the air conditioner Type Description The internal fan will be off to against cold air when the heat pump is Against cold air heating The internal fan will be off to against cold air when the heat pump is De ice cycle y heating D Q E Anti protection of The compressor will be off to protect internal battery when the air 2 internal battery conditioner operates in Cool mode The air conditioner does not start operating immediately to protect the Protect compressor compressor of the outdoor unit after it has been started 4 If the heat pump is operating in Heat mode De ice cycle is actuated to remove frost from an outdoor unit that may have deposited at low temperatures The internal fan is switched off automatically and restarted only after the de ice cycle is completed cleaning and maintaining 33 IB E 31763 1 10 11 11 indd 33 2010 11 11 14 42 04 appendik TROUBLESHOOTING Refer to the following chart if the air conditioner operates abnormally This may save time and unnecessary expenses PROBLEM SOLUTION The air conditioner does not operate immediately after it has been restarted Because of the protective mechanism the appliance does not start
3. 1 Open the front panel 9r Tightly grab the grooved surface on both side of t the front panel and lift the bottom side of the panel up until it gets locked Front panel of your air conditioner is actually not detachable 3 Clean the Air filter with a vacuum cleaner or soft brush If dust is too heavy then rinse it with running water and dry it in a ventilated area For the best conditions repeat every two weeks f the Air filter dries in a confined or humid area odors may generate If it occurs re clean and dry it in a well ventilated area 4 Insert the Air filter back in its original position 5 Close the front panel Grab the side of the front panel tightly and push it downward cleaning and maintaining _29 L ee HSI TION3 31763 1 10 11 11 29 e 2010 11 11 14 42 01 L cleaning and maintaining the air conditioner CLEANING THE FILTER Anti allergy filter Washable foam based Anti allergy filter leads to reduction in allergens that thrive in polluted air The filter is cleaned with a vacuum or by hand washing 1 Open the front panel Tightly grab the grooved surface on both side of the front panel and lift the bottom side of the panel up until it gets locked S 2 Remove the Air filter Grab th
4. conditioner at the desired time See page 23 for instructions To deactivate the Off timer 1 Press the Set Cancel button on the remote control Off timer you set will be canceled and Off timer indicator will disappear 22 using advanced functions IB 31763 1 10 11 11 indd 22 e 2010 11 11 14 41 41 L e Combining On timer and Off timer You can combine the On timer and Off timer together for more convenient use of the timer function 1 Set the On timer Press the On button Set the time with Up and Down button SetTemp Auto Ju Press Set Cancel button to activate the On timer c auto IE m 5 Timer od 4 See page 21 for more detail instructions on setting On gt E timer 2 Set the Off timer Press the Off button Set the time with Up and Down button Press Set Cancel button to activate the Off timer When you set the time there can be two possible options On timer is shorter than Off timer The air conditioner will turn on and then off automatically Set up should be done while the air STEMS conditioner is off IU For example If the On timer is set at 3 hours and 5 c ac E X the Off timer at 5 hours the air conditioner will turn Le E35 50 off automatically 3 hours after the set time and then i operate for next 2 hours before turning off automatically C CE Down timer is longer
5. more clean and healthier air 1 Press the CLEAN E button gt When the air conditioner is turned off The Evaporator clean indicator on the indoor unit display appears and the Evaporator cleaning function runs gt When the air conditioner is turned on The Evaporator clean indicator on the indoor unit display appears and the Evaporator cleaning function runs after stopping the air conditioner operation Evaporator Cleaning time can vary depending on the previously used mode Auto cool Cool Dry mode approximately 30 minutes Auto heat Heat Fan mode approximately 15 minutes 4 When the air conditioner is turned the Auto cleaning function runs after stopping the air conditioner operation SetTemp Auto 28 using advanced functions IB E 31763 1 10 11 11 indd 28 2010 11 11 14 42 00 cleaning and maintaining the air conditioner CLEANING THE EXTERIOR 1 Wipe the surface of the unit with a slightly wet or dry cloth when needed Do not use Benzene Thinner or Clorox ew They may damage the surface of the air conditioner and can create a risk of fire CLEANING THE FILTER When cleaning the filter make sure to unplug the power from the unit No special tools are needed to clean it Air filter Washable foam based air filter captures large particles from the air The filter is cleaned with a vacuum or by hand washing
6. Mode button on the remote control until Dry mode indicator appears on the remote control display Set Temp 4 1 The air conditioner operates mode LP nuto automatically adjusts the fan speed to Auto When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat Mode Fan Speed 3 Set the temperature Press the Temperature or A button on the remote En J e control to decrease or increase the desired temperature You can set the desired temperature between the range of 18 C 30 C 4 You decrease increase the temperature by 1 C When you are using the remote control make sure correct indicator which matches your Selection appears on the remote control display Air flow can be adjusted manually See page 19 for instructions 16 operating E 31763 1 10 11 114 44 16 2010 11 11 14 41 19 L e Fan Fan mode can be selected to ventilate your room Fan mode will be helpful to refresh the stale air in your room 1 Turn on the air conditioner Press the Power button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Fan mode indicator appears on the remote control display The air conditioner operates in Fan mode and automatically adjusts the temperature according to the current room temperature
7. a transmit indicator appears on the remote control display 12 viewing 31763 1 10 11 11indd 12 e 2010 11 11 14 41 02 Remote control display Set temperature Air swing indicator indicator lt arc Operating mode mpizone indicator b Rapid AutoSilence Turbo Set Temp AutoCoolDry Turbo indicator Fan speed indicator High EanHeat m Medium J ESaver Low 47741471 nergy saving O Auto LI LI C indicator 5 good sleep indicator good S O oo Transmit indicator sleep KO LL lu 03 LLLI Low battery indicator On Off Timer indicator Using the remote control Point the remote control towards the remote control sensor of the unit When properly pressing the button on the remote control you will hear beep sound from the unit 4 The signal be received well of electronic lighting style fluorescent lamps such as inverter fluorescent lamps are in the same space f other electrical products operate by the remote control call your nearest contact center Installing the batteries 1 Slide the cover on the 2 Install two AAA batteries 3 Close the cover by sliding rear side of the remote Check and match the it back to its original control down to open and signs accordingly position Make sure you have installed You should hear click sound the batteries in co
8. ensure that they do not play with the appliance Clean the air conditioner after the inner fan stops operating Potential risk of injury or electric shock Inspect the condition electric connections pipes and external case of the air conditioner regularly by a qualified service technician Do not open doors and windows in the room being cooled during operation unless necessary Do not block the air conditioner vents If objects block the air flow it may cause unit malfunction or poor performance Make sure there are no obstacles under the indoor unit Potential risk of fire or loss of property Make sure that there are no obstacles or covers that block the air conditioner Allow sufficient space for air circulation nsufficient ventilation may result in poor performance safety information 07 IB E 31763 1 10 11 1Lindd 7 e 2010 11 11 14 40 58 ND IVI Safety Information NCAUTION SIGNS Make sure the voltage and frequency of the electric system are compatible with the air conditioner If a power outage occurs while the air conditioner is working turn off the power source immediately Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency The unit must be plugged into an independent circuit if applicable or connect the power cable to the auxiliary circuit breaker An all pole disconnection from the power supply must b
9. operating immediately to keep the unit from overloading The air conditioner will start in 3 minutes The air conditioner does not work at all Check that the power plug is properly connected Insert the power plug into the wall socket correctly Check if the circuit breaker is switched off Check if there is a power failure Check your fuse Make sure it is not blown out The temperature does not change Check if you selected Fan mode Press the Mode button on the remote control to select another mode The cool warm air does not come out of the air conditioner Check if the set temperature is higher lower than the current temperature Press the Temperature or A button on the remote control to change the set temperature Press the Temperature or A button to decrease or increase the temperature Check if the air filter is blocked by dirt Clean the Air filter every two weeks Check if the air conditioner has just been turned on If so wait 3 minutes The fan speed does not change Check if you selected Auto or Dry mode The air conditioner automatically adjusts the fan speed to Auto in Auto Dry mode Timer function does not set Check if you press the Set Cancel button on the remote control after you have set the time Odors permeate in the room during operation Check if the appliance is running in a smoky area or if there is a smell entering from outside Operate the air condit
10. or disassembled NCAUTION SIGNS CAUTION N Connect the refrigerant tubes first then the electrical lines when installing the unit Always disassemble the electric lines before the refrigerant tubes Verify that the air conditioner is connected to the power supply in accordance with the instructions provided in the wiring diagram included in the manual The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper connection of electric and hydraulic lines Failure to comply with these instructions or to comply with the requirements set forth in the Operating limits table included in the manual and shall immediately invalidate the warranty Ensure no water gets into the air conditioner e Potential risk or electric shock Turn off the air conditioner using the provided remote control or control accessory if provided Do not unplug to turn off the unit unless there is an immediate danger Do not open the front grille during operation e Potential risk of electric shock or unit malfunction Cool air should not flow directly towards people pets and plants t is harmful to your health pets and plants Do not run the air conditioner for an extended period of time in a room with the door closed or with babies elderly or disabled people Open the door or windows to ventilate your room at least once an hour to prevent oxygen shortage Do not drink drain water coming
11. than Off timer The air conditioner will turn off and then on automatically Set up should be done while the air conditioner is operating SetTemp Auto For example If the On timer is set at 3 hours and Oe oF 6 Auto the Off timer at 1 hour the air conditioner will turn off automatically an hour after the set time and remain off for 2 hours before turning on automatically B5 B i 4 See page 22 for more detail instructions on setting Off timer To deactivate the timer combination 1 Press the Set Cancel button on the remote control Both of the On and Off timer will be canceled and the indicators will disappear using advanced functions 23 IB E 31763 1 10 11 11 23 e 2010 11 11 14 41 46 L 0 using advanced functions SETTING TIMER good sleep mode good sleep mode allows you to set a comfortable sleep temperature while saving energy and having sound sleep good sleep mode can be set up when the air conditioner is on 1 Set the operating mode Press the Mode button on the remote control until Cool Heat appears on the remote control display good sleep is only available in Cool Heat mode 2 Press the good sleep button on the remote control good sleep indicator appears and Off timer indicator starts blinking on the remote control display Set Temp Cool 3 Set the length of time you
12. while On timer indicator is blinking You can set the time up to 24 hours increasing in 30 minute unit up to first 3 hours and in hourly unit after first 3 hours Ju Ic 3 Press the Set Cancel button on the remote control to active it on The remote control display will show the hour s you have set The air conditioner will operate automatically at set time and then On timer indicator disappears If On timer is not set within 10 seconds the air conditioner will end setting 4 Setthe operating mode Press the Mode button on the remote control until the NEED desired mode appears on the remote control display 7 T The air conditioner will operate in the mode you set r z IS 3n E 31 Mode Fan Speed On timer function i ilable in Auto Cool Dry Fan Heat i nction is available in Auto Cool Dry Fan Hea 6 mode Temperature can also be adjusted See step 3 on page 15 for instructions After the set up while the unit is off approximately after 10 seconds all the other indicators will be gone except the On timer indicator and remaining time Setting time allows you to change by pressing the On button Press the Up or Down button to change time setting and then press the Set Cancel button to active it on To deactivate the On timer 1 Press the Set Cancel button on the remote control On timer you set will be canceled and On timer indicato
13. 11 14 42 04 Wall Mounted Type Series Vivace imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please register your product at WWW samsung Com register OOO DB98 31763A 1 2010 11 11 14 42 04 NDODOVOOOO IB 31763 1 10 11 1Lindd 37
14. 2010 11 11 14 40 57 Es NEM BNN C Install the supplied cables firmly Fix them securely so that external force is not exerted to the terminal block f the connection is loose heat may generate and cause electric shock or fire Use a rated circuit breaker only Never use steel wires or copper wires as a circuit breaker It may cause fire or unit malfunction Use an exclusive power source for the air conditioner Potential risk of electric shock or fire Do not put undue stress or place heavy object on the power cable Do not bend the power cable excessively Potential risk of fire or electric shock Always verify that electric connections cable entry section of leads protections are compliant with the electric specifications and with the instructions provided in the wiring scheme Always verify that all connections comply with the standards applicable to the installation of air conditioners HSITSNA X Use a receptacle that has a ground terminal The receptacle must be used exclusively for the air conditioner Improper electrical grounding may cause electric shock or fire Be sure to ground the unit Do not connect the ground wire to gas or water pipes lighting rods or telephone grounding lines e f the unit is not properly grounded electric shock may result Always verify that a suitable grounding connection is available Disconnect the air conditioner from power supply before it is repaired
15. NDODOVOOOO IB E 31763 1 10 11 1Lindd 1 2010 11 11 14 40 56 L e features of your new air conditioner e Cool Summer Offer On those hot sweltering summer days and long restless nights there is no better escape from the heat than the cool comforts of home Your new air conditioner brings an end to exhausting hot summer days and lets you rest This summer beat the heat with your own air conditioner e Cost Efficient System Your new air conditioner not only provides maximum cooling power in the summer but can also be an efficient heating method in the winter with the advanced Heat pump system This technology is up to 30096 more efficient than electrical heating so you can further reduce its running cost Now meet year round needs with one air conditioner e Look for Everywhere The elegant and harmonious design gives priority to the esthetics of your space and complements any of your existing interior d cor With its soft color and rounded edge shape the new air conditioner adds class to any room Enjoy what your air conditioner offers both functionally and esthetically e mpizone mpizone function generates hydrogen H and oxygen O to attack undesirable air contaminants such as bacteria pollen and odor It makes you breathe better as if you were staying around waterfalls ocean surf rivers and mountains good sleep function good sleep mode allows you to set a comfortable sleep temperature while
16. at 3 the Temperature Press the Temperature or A button on the remote control to decrease or increase the desired temperature SetTemp Auto You can set the desired temperature between the range of 16 C 30 C You can decrease increase the temperature by 1 C 4 When the air conditioner is already operating in another mode press the Mode button until Auto mode indicator appears on the remote control display When you are using the remote control make sure correct indicator which matches your Selection appears on the remote control display Air flow can be adjusted manually See page 19 for instructions 14 operating IB 31763 1 10 11 11indd 14 e 2010 11 11 14 41 09 L e Cool In Cool mode the air conditioner will cool your room You can adjust the temperature and the fan speed to feel cooler in hot season 1 Turn on the air conditioner Press the Power button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Cool mode indicator appears on the remote control display The air conditioner operates in Cool mode and it will lower the temperature in your room Set Temp Cool 4 When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat 3 Set the temperature Press the Temperature V or A button on the remote contro
17. bining On timer and Off timer 24 good sleep mode 26 Using the mpizone function 27 Using the Energy saving function 28 Using the Evaporator clean function CLEANING AND MAINTAINING 29 Cleaning the exterior THE AIR CONDITIONER 29 Cleaning the filter 29 Airfilter 30 Anti allergy filter 31 Replacing the filter 31 Deodorizing filter 32 Maintaining your air conditioner 32 Periodical checks 33 Internal protections via the unit control system APPENDIX 34 Troubleshooting 35 Operation ranges contents 09 NDODOVOOOO IB 31763 1 10 11 114 44 9 e 2010 11 11 14 40 58 NS e viewing your air conditioner Congratulations on the purchase of the air conditioner We hope you enjoy the features of your air conditioner and stay cool or warm with optimal efficiency Please read the user manual to get started and to make the best use of the air conditioner CHECKING THE INDOOR UNIT AND DIGITAL DISPLAY Carefully unpack your air conditioner and check the unit to make sure it is not damaged Main parts Air filter under the panel Air intake es wa Power 1 button Blade pin lever L Air flow blade Air flow blade 4 Your air conditioner may slightly look different from illustration shown above depending your model Indoor unit digital display mpizone indicator me Evaporator Timer good sleep CLEAN indicator ind
18. can set the desired temperature between 4 auto IE 5 e the range of 16 C 30 C Set Temp You can decrease increase the temperature by 1 C 4 Set the fan speed Press the Fan Speed button on the remote control to set the desired fan speed If room temperature reaches desired value heating will stop for a while Fan Speed Z e When you press the Fan Speed button fan speed will change order of Auto Low Medium High Fan may not operate for about 3 5 minutes at the beginning to prevent any cold blasts while the air conditioner is warming up 4 Air flow can be adjusted manually See page 19 for instructions Since the air conditioner heats the room by taking heat energy from outdoor air the heating capacity may decrease when outdoor temperatures are extremely low If you feel the air conditioner insufficiently heats using an additional heating appliance in combination with the air conditioner is recommended 18 operating IB 31763 1 10 11 11indd 18 e 2010 11 11 14 41 28 ADJUSTING THE AIR FLOW DIRECTION Air flow can be directed to your desired position Vertical air flow Air flow blades move up and down 1 Press the Air swing button the remote control remote control again Horizontal air flow prefer Air swing indicator will be on and the number of indicator lights move up and dow
19. cation cable of the indoor and outdoor unit at least 1m away from the electric appliance Install the indoor unit away from lighting apparatus using the ballast f you use the wireless remote control reception error may occur due to the ballast of the lighting apparatus For maximum safety installers should always carefully read the following warnings Do not install the air conditioner in following places Place where there is mineral oil or arsenic acid Resin parts flame and the accessories may drop or water may leak The capacity of the heat exchanger may reduce or the air conditioner may be out of order The place where corrosive gas such as sulfurous acid gas generates from the vent pipe or air outlet The copper pipe or connection pipe may corrode and refrigerant may leak The place where there is a machine that generates electromagnetic waves The air conditioner may not operate normally due to control system The place where there is a danger of existing combustible gas carbon fiber of flammable dust The place where thinner or gasoline is handled Gas may leak and it may cause fire If the air conditioner is installed in a small room measures must be taken to prevent the refrigerant concentration in the room from exceeding the safety limit in the event of refrigerant leakage Consult a dealer regarding the appropriate measures to prevent the allowable concentration from being exceeded e f the refrig
20. chine is grounded to prevent electric shock DEEA Call the contact center for help 7 S Recommended instructions or useful information for use These warning signs are here to prevent injury to you and others Please follow them carefully After reading this section keep it in a safe place for future reference SEVERE WARNING SIGNS Do not place the air conditioner near hazardous substances or equipment that releases free flames to avoid fire explosions or injuries e Potential risk of fire hazard or explosion Do not block or place items in front of the air conditioner Do not step hang onto or place heavy items on the air conditioner Potential risk of personal injury Do not install the outdoor unit at an unstable place or elevated surface where there is potential risk of falling e f the outdoor unit falls it may cause personal injury or loss or property Any changes or modifications performed not following by the installation manual failure or damage may occur on the condition In this case user will be responsible for all the repair expenses safety information 03 NDODOVOOOO IB E 31763 1 10 11 1Lindd 3 e 2010 11 11 14 40 57 L e Safety Information SEVERE WARNING SIGNS WARNING If any gas or impurities other than R410A refrigerant come into the refrigerant pipe serious problem may occur and it may cause injury Do not spray flammable gases such as insectic
21. e When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat 3 Set the fan speed Press the Fan Speed button on the remote control to set the desired fan speed F Mode Fan Speed O e 4 When you press the Fan Speed button fan speed will change in order of Low Medium and High e When you are using the remote control make sure correct indicator which matches your Selection appears on the remote control display Air flow can be adjusted manually See page 19 for instructions operating 17 31763 1 10 11 11indd 17 2010 11 11 14 41 22 L ee operating basic function SELECTING OPERATION MODE Heat The air conditioner heats as well as cools Warm your room with this versatile appliance in the cold of winter 1 Turn on the air conditioner Press the Power b button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Heat mode indicator appears on the remote control display The air conditioner operates in Heat mode and warms your room Set Temp When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat Mode Fan Speed 3 Set the temperature Press the Temperature V or A button on the remote control to decrease or increase the desired temperature IC You
22. e handle and lift it up Then pull the Air filter towards you and slide it down 3 Slide the Anti allergy filter color in sky blue out to remove it from the slot e Anti allergy filter can be placed in any 4 slots beneath the air filter e Front panel of your air conditioner is actually not detachable 4 Clean the Anti allergy filter with a vacuum cleaner or soft brush Then rinse it with running water and dry it in a ventilated area 5 Install the Anti allergy filter back in position 6 Close the front panel Grab the side of the front panel tightly and push it downward Clean the Anti allergy filter every 3 months The cleaning term may differ on usage and environmental conditions 30 cleaning and maintaining IB 31763 1 10 11 11 indd 30 2010 11 11 14 42 03 L e REPLACING THE FILTER Replacement filter may be purchased from the retail store or ordered from the dealer where you purchased the unit If you cannot find one please call a contact center Deodorizing filter Deodorizing filter absorbs efficiently cigarette smoke pet odors and other unpleasant smells Deodorizing filter cleaning is simple just remove old filter and install a new one 1 Open the front panel Tightly grab the grooved surface on both side of the front panel and lift the bottom side of the panel up until it gets locked
23. e incorporated in the fixed wiring with a contact opening of gt 3mm After connecting the power cable between the indoor outdoor unit attach the cover of component box securely and make sure it is not loose For the power cable use the grade of HO7RN F or HOSRN F materials The unbalanced power must be maintained within 10 of supply rating among whole indoor units If the power is unbalanced greatly it may shorten the life of the condenser If the unbalanced power is exceeded over 10 of supply rating the indoor unit is protected stopped and the error mode indicates To protect the product from water and possible shock you should keep the power cable and the connection cord of the indoor and outdoor units in the protection tube Connect the power cable to the auxiliary circuit breaker You must keep the cable in a protection tube Keep distances of 50mm or more between power cable and communication cable Maximum length of power cable is decided within 10 of power drop If it exceeds you must consider another power supplying method The circuit breaker MCCB ELB should be considered more capacity if many indoor units are connected from one breaker Use solderless ring terminal to connect the power cable to the power terminal block Use an appropriate screwdriver for tightening the terminal screws Over tightening the terminal screws may break them Ensure the off on and protection switches are properly installed Do
24. erant leaks and cause the concentration limit to be exceeded hazards due to lack of oxygen in the room may result Install the air conditioner away from direct exposure to sunlight heating apparatus and humid places Hang curtains on windows to boost cooling efficiency and to avoid the risk of electric shock The air conditioner is composed of moving parts Keep children away from the unit to avoid physical injury 06 safety information IB E 31763 1 10 11 114 44 6 2010 11 11 14 40 57 Es e OVO Check for damage on delivery If damaged do not install the air conditioner and call the place of purchase immediately Insert the dust filter before operating the air conditioner f there is no dust filter inside the air conditioner accumulated dust may shorten the life of the air conditioner and cause electricity waste Keep indoor temperatures stable and not extremely cold especially where there are children elderly or disabled people Clean the dust filter every 2 weeks Clean the filter more frequently if the air conditioner is operated in dusty areas The packaging material and used batteries of the remote controller optional must be disposed of in accordance with the national standards HSITSNA The refrigerant used in the air conditioner must be treated as chemical waste Dispose the refrigerant following national standards Have a qualified service technician install the ai
25. icator i a M Temperature indicator Operation indicator 10_ viewing 31763 1 10 11 114 44 10 2010 11 11 14 40 59 OPENING THE FRONT PANEL Tightly grab the grooved surface on both side of the front panel and lift the bottom side of the panel up until it gets locked in one position HSI TION3 Power button and Room temperature sensor You may locate the Power 1 button on the right bottom side of the air conditioner If the front panel is open you can check the room temperature sensor You can turn on the air conditioner without the remote control by pressing the Power 1 button The room temperature sensor measures indoor room temperature Room temperature sensor 1 Power 1 button Front panel of your air conditioner is actually not detachable viewing 11 NDODOVOOOO IB 31763 1 10 11 11indd 11 2010 11 11 14 41 00 L viewing your air conditioner CHECKING THE REMOTE CONTROL You can activate the air conditioner by pointing the remote control away from it When using the remote control always point it directly at the air conditi
26. ide near the air conditioner e Potential risk of electric shock fire or unit malfunction Do not insert anything such as fingers or branches into the air conditioner vents Keep children away from the air conditioner Potential risk of personal injury Do not cut the power plug and connect to a different power cable Never attempt to lengthen the power cable e Potential risk of fire or electric shock Do not yank the power cable and touch the power plug with hands e Potential risk of fire or electric shock Never use a damaged power plug power cable or loosened power receptacle e Potential risk of fire or electric shock The electric work must be done by qualified service technician in accordance with the national wiring regulations with rated cables f the capacity of the power cable is insufficient or electric work have not done properly electric shock or fire may occur You should connect the power cable into the power cable terminal and fasten it with a clamp Do not connect the air conditioner with heating apparatus or attempt to disassemble remodel or repair it by yourself e Potential risk of malfunction electric shock or fire If repairs are needed consult the contact center Consult the place of purchase or a contact center to disassemble or reinstall the air conditioner e Potential risk of unit malfunction water leakage electric shock or fire Consult the place of purchase or contact center to i
27. ioner in Fan mode or open the windows to air out the room The air conditioner makes a bubbling sound A bubbling sound may be heard when the refrigerant is circulating through the compressor Let the air conditioner operate in a selected mode Water is dripping from the air flow blades Check if the air conditioner has been cooling for an extended period of time with the air flow blades pointed downwards Condensation may generate due to the difference in temperature Remote control is not working Check if your batteries are depleted Make sure batteries are correctly installed Make sure nothing is blocking your remote control sensor Check that there are strong lighting apparatus near the air conditioner Strong light which comes from fluorescent bulbs or neon signs may interrupt the electric waves 34 appendix IB E 31763 1 10 11 1Lindd 34 2010 11 11 14 42 04 OPERATION RANGES The table below indicates the temperature and humidity ranges the air conditioner can be operated within Refer to the table for efficient use OPERATIONAL TEMPERATURE MODE INDOOR HUMIDITY IF OUT OF CONDITIONS INDOOR OUTDOOR Condensation may occur on COOLING 18C1032C 5 1043 CC 25 nocar unt emn Issue either water blow off or drops on the floor 77 T HEATING 27C orless 20C to 24 C Internal protection triggers and the air conditioner will st
28. ivers and mountains mpizone indicator on the indoor unit will fade in and fade out continuously when the mpizone function is activated 1 Press the mpizone On Off button on the remote control while the air conditioner off mpizone indicator will appear on the remote control display The air conditioner generates MPI in mpizone Auto mode 2 Set the operating type mpizone Rapid AutoSilencej Each time you press the Clean Mode button while the air conditioner is off the operating type will change in order of Auto Silence and Rapid Auto adjust the fan speed automatically Silence operate at a minimum fan speed quietly Rapid operate at a maximum fan speed to clean and purifies the air effectively and quickly The Clean Mode button will not work while the air conditioner is on When you activate the mpizone function while the air conditioner is on mpizone function automatically sets to Auto To deactivate mpizone mode 1 Press the mpizone On Off button on the remote control mpizone mode you set will be canceled and blue light will turn off 26 using advanced functions 31763 1 10 11 11 indd 26 e 2010 11 11 14 41 56 L e USING THE ENERGY SAVING FUNCTION This function will set the temperature range limit to help you save energy while the air conditioner is operating in Cool mode 1 Press the Energy saving 2 butto
29. l to decrease or increase the desired temperature Set Temp Cool 28 You can set the desired temperature between Auto the range 16 0 You can decrease increase the temperature by 1 C 4 Set the fan speed Press the Fan Speed button on the remote control to set Set Temp Cool the desired fan speed E If room temperature reaches desired value the air conditioner will shut off cooling for a while and just the fan runs Mode 4 When you press the Fan Speed button fan speed will em change in order of Auto Low Medium and High 4 When you are using the remote control make sure correct indicator which matches your Selection appears on the remote control display Air flow can be adjusted manually See page 19 for instructions f current outside temperatures are much higher than the selected indoor temperature it may take time to bring the inner temperature to the desired coolness operating 15 IB 31763 1 10 11 11 indd 15 e 2010 11 11 14 41 15 L 0 operating basic function SELECTING OPERATION MODE Dry The air conditioner in Dry mode acts like a dehumidifier by removing moisture from the indoor air Dry mode makes the air feel refreshing in a humid climate 1 Turn on the air conditioner Press the Power b button on the remote control 2 Set the operating mode Press the
30. n m Air flow blades move up and down continuously to circulate the air O gt To keep the air flow direction in a constant position press the Air swing button the E Set Temp Auto JLI Auto Make sure one of the blade pins that stick out of the air flow blades are not broken 1 Move the blade pin lever left or right to keep the air flow direction in a constant position you Be extremely careful with your fingers while adjusting the Horizontal air flow direction amon There is a potential risk of personal injury when the unit is mishandled operating 19 2010 11 11 14 41 30 IB 31763 1 10 11 11indd 19 L ee using advanced functions USING THE TURBO FUNCTION Turbo function will be helpful to cool or heat your room quickly and effectively by operating at the maximum fan speed for 30 minutes 1 Turn on the air conditioner Press the Power b button on the remote control 2 Set the operating mode Press the Turbo g button on the remote control until Auto Cool HeatTurbo Turbo indicator appears on the remote control display The air conditioner operates in Turbo fan speed and automatically adjusts the temperature according to the current room temperature The unit operates for 30 minutes and then operates in last used mode or in Auto mode if Dry Fan mode is most recent mode used Turbo function is only available in Auto Cool Heat mode If Turbo f
31. n off when the set time has elapsed Three stage good sleep prevents you from having difficulty sleeping in summer winter night Fall asleep Eases you into sleep by dropping the temperature Sound sleep Relaxes your body and raises your temperature slightly amp Wake up from good sleep mode Allows you to wake up from comfortable intermittent air and it makes you feel refresh HSITSNA 4 Set Off timer in good sleep mode over 5 hours You feel disturbed sleep if the good sleep is set too short or long because the default is set to 8 hour operation f the good sleep mode is set less than 4 hours the operation will stop at the set time If the good sleep mode is set over 5 hours it will run as Wake up stage for the last one hour before stop Recommended set temperature is between 25 C 27 C for cooling and 21 C 23 C for heating To deactivate good sleep mode 1 Press the Set Cancel button on the remote control good sleep mode you set will be canceled and good sleep indicator will disappear using advanced functions 25 IB 31763 1 10 11 11 indd 25 2010 11 11 14 41 52 L using advanced functions USING THE mpizone FUNCTION MPI Micro Plasma lon zone generates hydrogen H and oxygen O to remove a polluted substance and decomposition of such harmful particles It makes you breathe better as if you were staying around waterfalls ocean surf r
32. n on the remote control while the air conditioner is operating in Cool mode SetTemp Cool m E Saver E Saver indicator and air swing indicator appear Cie automatically on the remote control display The air flow blades move up and down If the current set temperature is lower than 26 C it will automatically raise to 26 C HSITSNA 4 Energy saving function is only available Cool mode When Energy saving function is activated temperature range will be limited to 26 C 30 C f the desired temperature is lower than 26 C turn off the energy saving function by pressing the Energy saving 9 button again Temperature Fan speed can also be adjusted See step 3 4 on page 15 for instructions Air flow can be adjusted manually See page 19 for instructions To deactivate the Energy saving function 1 Press the Energy saving 2 button on the remote control Energy saving function you set will be canceled and Energy saving indicator will disappear on the remote control display using advanced functions 27 IB E 31763 1 10 11 11 indd 27 2010 11 11 14 41 58 L using advanced functions USING THE EVAPORATOR CLEAN FUNCTION Evaporator clean function will prevent from growing mold by eliminating the moisture inside of the indoor unit Your indoor unit evaporates the moisture inside of the unit Activate this function to provide you with
33. not use the air conditioner if damaged If problems occur immediately stop operation and disconnect the plug from the power supply If the air conditioner will not be used for an extended period of time for example over several months unplug the power from the wall IB E 31763 1 10 11 1Lindd 8 e 2010 11 11 14 40 58 Call the place of purchase or a contact center if repairs are needed Potential risk of fire or electric shock if disassembly or repairs are attempted by a non qualified Service technician If you smell burning plastic hear strange sounds or see smoke coming from the unit unplug the air conditioner immediately and call a contact center Potential risk of fire or electric shock 08 safety information L e contents VIEWING YOUR AIR CONDITIONER Checking the indoor unit and digital display jain parts ndoor unit digital display Removing the front panel Power button and Room temperature sensor Checking the remote control Remote control display Using the remote control nstalling the batteries c ah adhi geek i s im i HSITSNA OPERATING BASIC FUNCTION 14 Turning the air conditioner on and off 14 Selecting operation mode 14 Auto 5 Cool 6 Dry 7 Fan 18 9 Adjusting air flow direction 9 Vertical air flow 9 Horizontal air flow USING ADVANCED FUNCTIONS 20 Using the Turbo function 21 Setting timer 21 Ontimer 22 Off timer 23 Com
34. nstall the air conditioner e Improper installation carries a risk of unit malfunction water leakage electric shock or fire f installing in specialty areas such as a factory complex or saline coastal area consult the place of purchase or contact center for specific installation details Install the air conditioner with the support bracket securely fastened to use for an extended period of time f the air conditioner falls it may cause personal injury or loss of property If the indoor unit gets wet turn the power off immediately and call your nearest contact center Potential risk of fire or electric shock Install an exclusive circuit breaker and short circuit breaker for the air conditioner Potential risk of electric shock or fire If the power cable is damaged the manufacturer or a qualified service technician must replace it Always make sure that the power supply is compliant with current safety standards Always install the air conditioner in compliance with current local safety standards Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is sufficient to ensure the operation of any other domestic appliance connected to the same electric lines The air conditioner must be installed in accordance with national wiring regulations and safety regulations wherever applicable 04 safety information IB E 31763 1 10 11 1Lindd 4 e
35. oner Remote control display Temperature V A Decrease Increase the temperature by 1 C Power D Turn on off the air conditioner Fan speed Adjust how much air flows through the air conditioner with the 4 different fan speeds such as Auto Low Medium High Mode Set one of the 5 operating modes See pages 14 18 for instructions Digital z On Off Set to turn on off the digital display of the unit during operation Operating mode e indicator still remains on pigtaiowot Air swing am pe E Activate Deactivate air flow blade pe f Turbo z tat movement automatically up and Operate in maximum fan speed to N A down cool warm Quickly On Up Set Cancel Sikap oe SS Evap CLEAN Energy saving function 9 Off Down On Off Clean Mode Evaporator clean function Dry Less energy usage makes your inside of the indoor unit to get rid of Space cool between the odor temperature range of 26 C 30 C Ti functi mpizone function Tunction On Off On Off Emit hydrogen H and Set the timer on off in the air to remove polluted substances such harmful Up Down particles Increase Decrease the time Clean Mode Set Cancel Set one of the 3 mpizone Set Cancel the current operating types timer good sleep mode setting B d good sleep Set the good sleep mode on off Each time you press the button a short beep will sound and
36. op Condensation may occur on DRYING 18C to 32 C 5 C to 43 C the indoor unit with risk to have either water blow off or drops on the floor The standardized temperature for heating is 7 C If the outdoor temperature drops to OC or below the heating capacity can be reduced depending on the temperature condition If the cooling operation is used at over 32 C indoor temperature it does not cool at its full capacity appendix 35 2010 11 11 14 42 04 IB 31763 1 10 11 11 35 _ SE QUESTIONS OR COMMENTS COUNTRY CALL OR VISIT US ONLINE AT ARGENTINE 0800383 9 88 wawasamsung com BRAZIL jana www samsung com 5 CHILE 800 SAMSUNG 726 7864 www samsung com NICARAGUA 00 1800 5077267 www samsung com HONDURAS 800 7919267 www samsung com COSTA RICA 0 800 507 7267 www samsung com L ECUADOR 1 800 10 7267 www samsung com EL SALVADOR 800 6225 www samsung com GUATEMALA 1 800 299 0013 www samsung com JAMAICA 1 800 234 7267 www samsung com 800 7267 www samsung com PUERTO RICO 1 800 682 3180 www samsung com DOMINICA 1 800 751 2676 www samsung com 1 TRINIDAD amp TOBAGO 1 800 SAMSUNG 726 7864 www samsung com 0 800 777 08 www samsung com l VENEZUELA 0 800 100 5303 www samsung com L COLOMBIA 01 8000112112 www samsung com NDODOVOOOO IB E 31763 1_10 11 11 indd 36 e 2010 11
37. out of the air conditioner Potential risk of health hazard safety information 05 IB E 31763 1 10 11 1Lindd 5 e 2010s VTSTE 14 40 57 L e Safety Information NCAUTION SIGNS Do not expose the dust filter to direct sunlight while drying Strong direct sunlight may deform the dust filter Do not allow children to climb on the air conditioner Use only rated accessories and install the air conditioner with rated equipments f you do not use the rated accessories the air conditioner may drop from its place water may leak or electric shock or fire may occur Do not use the air conditioner as a cooling precision instrument for food pets plants cosmetics or machinery Do not give excessive shock to the air conditioner Potential risk of fire or unit malfunction Do not spray water directly on the air conditioner or use benzene thinner or alcohol to clean the surface of the unit Potential risk of electric shock or fire Potential risk of damage to the air conditioner Do not place any objects especially containers with liquid Do not touch the pipe connected to the air conditioner This appliance should be installed according to the provided installation manual Install the shortest possible length of pipe f the length of pipe gets unnecessarily long the life of air conditioner can be shorten and become inefficient Install the power cable and communi
38. r conditioner and perform a trial operation Firmly connect the drain hose to the air conditioner for proper water drainage Install the outdoor unit where operating noise and vibration will not disturb your neighbor and in a well ventilated area with no obstacle e Potential risk of malfunction Operating noise may disturb your neighbor Make sure that children take precautions against access to the air conditioner and they do not play with the unit When using a wireless remote control the distance should not be more than 7 meters from the air conditioner If the remote control is not used for a long period of time remove the batteries to prevent leakage of electrolyte When cleaning the outdoor unit touch the heat exchanger radiator fins with extreme care Wearing thick gloves can protect your hands Make sure that the condensed water dripping from the drain hose runs out properly and safely Store the operation and installation manual in a safe location and remember to hand it over to the new owner if the air conditioner is sold or transferred All the materials used for the manufacture and packaging of the air conditioner are recyclable After completing the installation always carry out a functional test and provide the instructions on how to operate the air conditioner to the user The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to
39. r will disappear using advanced functions 21 IB 31763 1 10 11 11 indd 21 e 2010 11 11 14 41 38 L 0 Using advanced functions SETTING TIMER Off timer This function allows you to turn off the air conditioner automatically within the time range of 24 hours Off timer is functional when the unit is operating 1 Press the Off button on the remote control Off timer indicator blinks on the remote control display SetTemp Auto 2 Set the time you want the air conditioner to turn off automatically SetTemp Auto Press the Up or Down button on the remote control to change the time setting while Off timer indicator is blinking You can set the time up to 24 hours increasing in 30 minute unit up to first 3 hours and in hourly unit after first 3 hours 3 Press the Set Cancel button on the remote control to active it on The remote control display will show the hour s you have set The air conditioner will turn off automatically at set time and then Off timer indicator disappears If Off timer is not set within 10 seconds the air conditioner will end setting e Setting time allows you to change by pressing the Off button Press the Up or Down button to change the time setting and then press the Set Cancel button to active it on You can combine Off timer function with On timer function to turn on and then off the air
40. rrect when the cover is locked position properly viewing _13 e 2010 11 11 14 41 04 IB 31763 1 10 11 11 13 L operating basic function TURNING THE AIR CONDITIONER ON AND OFF Press the Power b button on the remote control You will hear a ringing sound and the air flow blade will move up and down automatically when the air conditioner is properly on The air conditioner will operate in the most recent operation mode used or Auto mode When you turn off the air conditioner air flow blade will stop moving and remain closed Turning on off your air conditioner without the remote control You can operate your air conditioner by pressing the Power b button on the right bottom side of the air conditioner SELECTING OPERATION MODE Auto In Auto mode the air conditioner will automatically set the temperature and fan speed depending on the room temperature detected by the room temperature sensor 1 Turn on the air conditioner Press the Power b button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Auto E o mode and Auto fan speed indicator appear on the remote control display The air conditioner will automatically set the operation mode to Cool or Heat depends on the room temperature 4 When you press the Mode button mode will change in order of Auto Cool Dry Fan and He
41. saving energy and having sound sleep e For easy future reference write the model and serial number Model down You will find your model number on the bottom of the Serial air conditioner erla 02_ features 31763 1 10 11 114 44 2 2010 11 11 14 40 56 L e safety Information To prevent electric shock disconnect the power before servicing cleaning and installing the unit SAFETY INFORMATION Before using your new air conditioner please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Because the following operating instructions cover various models the characteristics of your air conditioner may differ slightly from those described in this manual If you have questions call your nearest contact center or find help and information online at www samsung com HSITSNA What the icons and signs in this user manual mean A Risk of death or serious personal injury WARNING Potential risk of personal injury or material damage CAUTION gt To reduce the risk of fire explosion electric shock or personal injury when CAUTION using your air conditioner follow these basic safety instructions Do NOT attempt Do NOT disassemble Do NOT touch Follow directions carefully Unplug the power plug from the wall socket Make sure the ma
42. sing the air conditioner again dry the inner components of the air conditioner again by running in Fan mode for 3 to 4 hours This helps remove odors which may have generated from dampness Periodical checks Refer to the following chart to maintain the air conditioner properly Type Description Monthly Ed po Clean the air filter 1 e Clean the condensate drain pan 2 e Indoor unit Thoroughly clean the heat exchanger 2 e Clean the condensate drain pipe 2 e Replace the remote control batteries 1 e Clean the heat exchanger on the outside of e the unit 2 Clean the heat exchanger on the inside of the unit 2 Clean the electric components with jets of air 2 Verify that all the electric components are e firmly tightened 2 Clean the fan 2 e Verify that all the fan assembly is firmly e tightened 2 Clean the condensate drain pan 2 e 4 The checks and maintenance operations described are essential to guarantee the efficiency of the air conditioner The frequency of these operations varies according to the characteristics of the area the amount of dust etc 1 The described operations should be performed more frequently if the area of installation is very dusty 2 These operations must always be performed by qualified personnel For more detailed information see the Installation Manual 32 cleaning and maintaining
43. unction is selected in Dry Fan mode operating mode changes to Auto To deactivate Turbo function 1 Press the Turbo z button on the remote control again The air conditioner operates in last used mode or in Auto mode if Dry Fan mode is most recent mode used When you are using the remote control make sure corresponding indicator appears on the remote control display Temperature Fan speed cannot be adjusted while using this function Air flow can be adjusted manually See page 19 for instructions When the Turbo function is activated pressing Mode button will automatically cancel the function 20 using advanced functions IB 31763 1 10 11 11 indd 20 2010 11 11 14 41 33 L e SETTING TIMER This advanced Timer function allows you to turn on off your air conditioner automatically even when you are away Simply set the time and your air conditioner will turn on off automatically On timer This function allows you to turn on the air conditioner automatically within the time range of 24 hours On timer is available while your air conditioner is on off 1 Press the On button on the remote control On timer indicator blinks on the remote control display SetTemp Auto 2 Set the time you want the air conditioner to turn on automatically Set Temp Auto Press the Up or Down button on the remote control to change the time setting
44. want the air conditioner to stay on Set Temp Default good sleep time is set to 8 hours Press the 75 Up or Down button on the remote control to change the c time setting while Off timer indicator is blinking m You can set the time up to 12 hours increasing in 30 minute unit up to first hours and in hourly unit after C es first 3 hours 4 Press the Set Cancel button on the remote control to active it on The remote control display will show the hour s you have set When the set time has elapsed the air conditioner will automatically turn off and then good sleep indicator disappears If good sleep mode is not set within 10 seconds the air conditioner will end setting 4 e Temperature Fan speed Air swing can be adjusted after setting good sleep in Heat mode Temperature can be adjusted and the air conditioner automatically adjusts the Fan speed Air swing after setting good sleep in Cool mode 24 using advanced functions IB E 31763 1 10 11 11 indd 24 e 2010 11 11 14 41 51 L e Temperature changes in good sleep mode To prevent excessive cooling heating during sleep the good sleep mode automatically modifies the temperature setting in accordance with the time setting Temperature and air current change according to the three stages Fall asleep Sound sleep and Wake up from good sleep mode and then the air conditioner will automatically tur
Download Pdf Manuals
Related Search