Samsung AQ07RLX Керівництво користувача
Contents
1. 2 Remove the Air filter Grab the handle and lift it up Then pull the Air filter towards you and slide it down 3 Slide the Deodorizing filter color in black out to remove it from the slot Deodorizing filter can be placed in any 4 slots beneath the air filter 4 Install the new Deodorizing filter back in position 5 Close the front panel K The replacement timing of the Deodorizing filter differs depending on usage and environmental conditions e Even if Deodorizing and Bio filters are installed in an inverted position it will not affect its filtration system cleaning and maintaining _29 cleaning and maintaining the air conditioner MAINTAINING YOUR AIR CONDITIONER If the air conditioner will not be used for an extended period of time dry the air conditioner to maintain it in best condition 1 Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and disconnect the power plug There may be internal damage if moisture is left in components 2 Before using the air conditioner again dry the inner components of the air conditioner again by running in Fan mode for 3 to 4 hours This helps remove odors which may have generated from dampness Periodical checks2. If the current set temperature is lower than 26 C it will automatically raise to 26 C SET TEMP e gt good sleep d q P IZ Smart Saver function is only available in Cool mode When Smart Saving function is activated temperature range will be limited to 26 C 30 C If the desired temperature is lower than 26 C turn off the Smart Saving function by pressing the Smart Saver button again Temperature Fan speed can also be adjusted See step 3 4 on page 15 for instructions Air flow can be adjusted manually See page 19 for instructions When the Smart Saver function is activated pressing Mode button will automatically cancel the function To deactivate the Smart Saving function 1 Press the Smart Saver button on the remote control Smart Saver function you set will be canceled and Smart Saving in dicator will disappear on the remote control display 26_ using advanced functions cleaning and maintaining the air conditioner CLEANING THE EXTERIOR 1 Wipe the surface of the unit with a slightly wet or dry cloth when needed HSIMONA Do not use Benzene Thinner or Clorox amon They may damage the surface of the air conditioner and can create a risk of fire CLEANING THE FILTER When cleaning the filter make sure to unplug the power from the unit No special tools are
3. Refer to the following chart to maintain the air conditioner properly Every 4 Oncea Type Description Monthly Months year Clean the air filter 1 gt Clean the condensate drain pan 2 Indoor unit Thoroughly clean the heat exchanger 2 Clean the condensate drain pipe 2 4 Replace the remote control batteries 1 C Clean the heat exchanger on the outside of A the unit 2 Clean the heat exchanger on the inside of the unit 2 Clean the electric components with jets of air 2 Outdoor unit Verify that all the electric components are firmly tightened 2 Clean the fan 2 Verify that all the fan assembly is firmly P tightened 2 Clean the condensate drain pan 2 q This check mark requires checking the indoor outdoor unit periodically following to the description to maintain the air conditioner properly The checks and maintenance operations described are essential to guarantee the efficiency of the air conditioner The frequency of these operations varies according to the characteristics of the area the amount of dust etc 1 The described operations should be performed more frequently if the area of installation is very dusty 2 These operations must always be performed by qualified personnel For more detailed information see the Installation Manual 30_ cleaning and maintaining Internal protections via the unit control s
4. Mount with the lowest moving parts at least 2 5m above the floor or grade level If applicable If failure or damage occurs on the conditions of improper use not followed by the installation manual there will be an extra labor charge for installing and construction e Potential risk of malfunction electric shock or fire if repairs or installations are attempted by a non qualified service technician Do not block or place items in front of the air conditioner Do not step hang onto or place heavy items on the air conditioner e Potential risk of personal injury Do not allow children to climb on the air conditioner Do not pull or give excessive shock to the air conditioner e Potential risk of fire or unit malfunction and there are risk of personal injury because unit may fall down Do not drink drain water coming out of the air conditioner e Potential risk of health hazard Do not spray flammable gases such as insecticide near the air conditioner e Potential risk of electric shock fire or unit malfunction Do not use the air conditioner as a cooling precision instrument for food pets plants cosmetics or machinery Cool air should not flow directly towards people pets and plants e It is harmful to your health pets and plants Do not spray water directly on the air conditioner or use benzene thinner or alcohol to clean the surface of the unit e Potential risk of electric shock or fire e Potential risk of dama
5. You can operate your air conditioner by pressing the Power button on the right bottom side of the air conditioner SELECTING OPERATION MODE Auto In Auto mode the air conditioner will automatically set the temperatur e and fan speed depending on the room temperature detected by the room temperature sensor 1 Turn on the air conditioner Press the Power l button on the remote control 2 Set the operating mode Auto SETTEMP r oat Ht FC Press the Mode button on the remote control until Auto mode and Auto fan speed indicator appear on the remote control display The air conditioner will automatically set the operation mode to Cool or Heat depends on the room temperature When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat 3 Set the Temperature SET TEMP ba Fi Ko Press the Temp A or V button on the remote control to increase or decrease the desired temperature d You can set the desired temperature between the Fal range of 16 C 30 C IZ You can increase decrease the temperature by 1 C Z e When the air conditioner is already operating in another mode press the Mode button until Auto mode indicator appears on the remote control display When you are using the remote control make sure correct indicator which matches your selection appears on the remote control display Air flow can be adjusted manually See p
6. air conditioner on and off Selecting operation mode Auto Cool Dry Fan Heat Adjusting the air flow direction Vertical air flow Horizontal air flow Using the Turbo function Setting timer On timer Off timer Combining On timer and Off timer good sleep mode Using the Smart Saver function Cleaning the exterior Cleaning the filter Air filter option Bio filter option Replacing the filter Deodorizing filter Maintaining your air conditioner Periodical checks Internal protections via the unit control system Troubles hooting Operation ranges This product has been determined to be in compliance with the Low Voltage Directive 2006 95 EC and the Electromagnetic Compatibility Directive 2004 108 EEC of the European Union g Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they ca
7. button on the remote control to active it on The remote control display will show the hour s you have set for 3 seconds and set desired temperature will display When the set time has elapsed the air conditioner will automaticall y turn off and then good sleep indicator disappears If good sleep mode is not set within 10 seconds the air conditioner will end setting iY Temperature Fan speed Air swing can be adjusted after setting good sleep in Heat mode e Temperature can be adjusted and the air conditioner automatically adjusts the Fan speed Air swing after setting good sleep in Cool mode When the good sleep function is activated pressing Mode button will automatically cancel the function 24_ using advanced functions Temperature changes in good sleep mode To prevent excessive cooling heating during sleep the good sleep mode automatically modifies the temperature setting in accordance with the time setting Temperature and air current change according to the three stages Fall asleep Sound sleep and Wake up from good sleep mode and then the air conditioner will automatically turn off when the set time has elapsed Three stage good sleep prevents you from having difficulty sleeping in summer winter night Fallasleep Eases you into sleep by dropping the temperature Sound sleep Relaxes your body and raises your temperature slightly Wake up from good sleep mode Allows you
8. indicator which matches your selection appears on the remote control display Air flow can be adjusted manually See page 19 for instructions If current outside temperatures are much higher than the selected indoor temperature it may take time to bring the inner temperature to the desired coolness operating _15 operating basic function SELECTING OPERATION MODE Dry The air conditioner in Dry mode acts like a dehumidifier by removing moisture from the indoor air Dry mode makes the air feel refreshing in a humid climate 1 Turn on the air conditioner Press the Power button on the remote control 2 Set the operating mode Dry Press the Mode button on the remote control until SET T J Lic Dry mode indicator appears on the remote control display The air conditioner operates in Dry mode and automatically adjust the fan speed to Auto Z When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat 3 Set the temperature 3 ry Press the Temp A or V button on the remote control to increase or decrease the desired temperature You can set the desired temperature between the range of 18 C 30 C You can increase decrease the temperature by 1 C A e When you are using the remote control make sure correct indicator which matches your selection appears on the remote control display e Air flow can be adjusted manually S
9. needed to clean it Air filter Washable foam based air filter captures large particles from the air The filter is cleaned with a vacuum or by hand washing 1 Open the front panel Tightly grab front side of the front panel and lift up the panel to open Then slightly push the panel up until the panel is hanged over the hooks of the unit jee aoe if 3 N sf H J f E re ee A LETTI A i afa Ze ie Se ae 2 tay A co LS 3 Clean the Air filter with a vacuum cleaner or soft brush If dustis too heavy then rinse it with running water and dry it in a ventilated area K For the best conditions repeat every two weeks e If the Air filter dries in a confined or humid area odors may generate If it occurs re clean and dry it in a well ventilated area 4 Insert the Air filter back in its original position 5 Close the front panel cleaning and maintaining _27 cleaning and maintaining the air conditioner Bio filter Option Washable foam based Bio filter leads to reduction in allergens that thrive in polluted air The filter is cleaned with a vacuum or by hand washing 1 Open the front panel Tightly grab front side of the front panel and lift up the panel to open Then slightly push the panel up until the panel is hanged over the hooks of t
10. Vi val di B_DB98 30079A E 12 19 2008 10 43 AM Page 1 1 1 AQOZ7ZR Series AQO9R Series OLTA ES AQO09C Series AQ12U Series AQ18U Series imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please register your product at www samsung com global register ei E R DB98 30079A features of your new air conditioner Cool Summer Offer On those hot sweltering summer days and long restless nights there is no better escape from the heat than the cool comforts of home Your new air conditioner brings an end to exhausting hot summer days and lets you rest This summer beat the heat with your own air conditioner Cost Efficient System Your new air conditioner not only provides maximum cooling power in the summer but can also be an efficient heating method in the winter with the advanced Heat pump system This technology is up to 300 more efficient than electrical heating so you can further reduce its running cost Now meet year round needs with one air conditioner A Look for Everywhere The elegant and harmonious design gives priority to the esthetics o f your space and complements any of your existing interior d cor With its soft color and rounded edge shape the new air conditioner adds class to any room Enjoy what your air conditioner offers both functionally and esthetically good sleep function good sleep function allows you to se
11. age 19 for instructions 14_ operating Cool In Cool mode the air conditioner will cool your room You can adjust the temperature and the fan speed to feel cooler in hot season 1 Turn on the air conditioner Press the Power button on the remote control 2 Set the operating mode Cool Press the Mode button on the remote control until SET TEM C zZ Cool mode indicator appears on the remote control I i display Hal T The air conditioner operates in Cool mode and it will lower the temperature in your room K When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat 3 Set the temperature Cool Press the Temp A or V button on the remote control SET TEME C to increase or decrease the desired temperature You can set the desired temperature between the range of 16 C 30 C Z You can increase decrease the temperature by 1 C 4 Set the fan speed Press the Fan lt or button on the remote control to _ C set the desired fan speed If room temperature reaches desired value the air conditioner will shut off cooling for a while and just the fan runs When you press the Fan lt or gt button fan speed will change in order of Auto Low Medium and High IZ When you are using the remote control make sure correct
12. an be directed to your desired position Vertical air flow Air flow blades move up and down 1 Press the Air swing button on the remote control Air swing indicator will be on and air flow blades move up and down continuously to circulate the air HSIONA To keep the air flow direction in a constant position press the Air swing button on the remote control again Auto SET TEMP h qc Horizontal air flow Make sure one of the blade pins that stick out of the air flow blades are not broken 1 Move the blade pin lever left or right to keep the air flow direction in a constant position you prefer Be extremely careful with your fingers while adjusting the Horizontal air flow direction danon There is a potential risk of personal injury when the unit is mishandled operating _19 using advanced functions USING THE TURBO FUNCTION Turbo function will be helpful to cool or heat your room quickly and effectively by operating at the maximum fan speed for 30 minutes 1 Turn on the air conditioner Press the Power button on the remote control 2 Set the operating mode Press the Turbo 2 button on the remote control until Turbo indicator appears on the remote control display The air conditioner operates in Auto fan speed and automatically adjusts the temperature according to the current room temperature The unit operates for 30 mi
13. ar using advanced functions _21 using advanced functions SETTING TIMER Off timer This function allows you to turn off the air conditioner automatically within the time range of 24 hours Off timer is available while your air conditioner is on off 1 Pressthe OffTimer button on the remote control Off timer indicator blinks on the remote control display 2 Set the time you want the air conditioner to turn off automatically Press the Off Timer button on the remote control to change the time setting while Off timer indicator is blinking You can set the time up to 24 hours increasing in 30 minute unit up to first 3 hours and in hourly unit after first 3 hours 3 Pressthe Set Cancel button on the remote control to active it on The remote control display will show the hour s you have set for 3 seconds and set desired temperature will display The air conditioner will operate automatically at set time and then Of f timer indicator stops blinking and stays on If Off timer is not set within 10 seconds the air conditioner will end setting 4 e Time setting can be changed by pressing the Off Timer button Press the Off Timer button to change the time setting and then press the Set Cancel button to active it on You can combine Off timer function with On timer function to turn on and then off the air conditioner at the desired time See page 23 for instructions To dea
14. crease Decrease the temperature by 1 C good sleep Set the good sleep mode on Set Cancel Set Cancel the timer good sleep function Off Timer Set the Off Timer on Adjust the timer for off timer Each time you press the button a short beep will sound and a transmit indicator appears on the remote control display Remote control display On Timer indicator indicator O good sleep indicator Ser Set temperature o A time indicator Off Timer indicator OFF HR Low battery indicator gt Transmit indicator T Fan speed indicator TSR 9 oy ae M Turbo indicator l Auto ff al Ss Low Smart Saver indicator Shar Medium Saal High HSIONA Air swing indicator Using the remote control Point the remote control towards the remote control sensor of the unit e When properly pressing the button on the remote control you will hear beep sound from the unit l4 The signal may not be received well of electronic lighting style fluorescent lamps such as inverter fluorescent lamps are in the same space e If other electrical products operate by the remote control call your nearest contact center Inserting the batteries 1 Push the lever as arrow 2 Insert two AAA batteries 3 Close the cover by place it indicates on the rear side Check and match the and back to its original position of the remote contro
15. ctivate the Off timer 1 Pressthe Set Cancel button on the remote control Off timer you set will be canceled and Off timer indicator will disappear 22_ using advanced functions Combining On timer and Off timer You can combine the On timer and Off timer together for more convenient use of the timer function 1 Set the On timer Press the On Timer button Set the time with On Timer button Press Set Cancel button to activate the On timer HSIONA Z See page 21 for more detail instructions on setting On timer 2 Set the Off timer Press the Off Timer button Set the time with Off Timer button Press Set Cancel button to activate the Off timer When you set the time there can be two possible options On timer is shorter than Off timer The air conditioner will turn on and then off automatically Set up should be done while the air conditioner is off For example If the On timer is set at 3 hours and the Off timer at 5 hours the air conditioner will turn off automatically 3 hours after the set time and then operate for next 2 hours before turning off automatically On timer is longer than Off timer The air conditioner will turn off and then on automatically Set up should be done while the air conditioner is operating For example If the On timer is set at 3 hours and the Off timer at 1 hour the air conditioner will turn off automatically an hour after th
16. e set time and remain off for 2 hours before turning on automatically See page 22 for more detail instructions on setting Off timer To deactivate the timer combination 1 Pressthe Set Cancel button on the remote control Both of the On and Off timer will be canceled and the indicators will disappear using advanced functions _23 using advanced functions SETTING TIMER good sleep mode good sleep mode allows you to set a comfortable sleep temperature while saving energy and having sound sleep good sleep mode can be set up when the air conditioner is on 1 Set the operating mode Cool Press the Mode button on the remote control until se TEM C Cool Heat appears on the remote control display good sleep is only available in Cool Heat mode 2 Press the good sleep button on the remote control good sleep indicator appears and Off timer indicator m cr starts blinking on the remote control display Walden HR 3 Set the length of time you want the air conditioner to stay on Default good sleep time is set to 8 hours alle hR Press good sleep button on the remote control to Saf change the time setting while Off timer indicator is You can set the time up to 12 hours increasing in aol 30 minute unit up to first 3 hours and in hourly unit after as a first 3 hours 4 Pressthe Set Cancel
17. ee page 19 for instructions 16_ Fan Fan mode can be selected to ventilate your room Fan mode will be helpful to refresh the stale air in your room 1 Turn on the air conditioner Press the Power l button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Fan mode indicator appears on the remote control display The air conditioner operates in Fan mode and circulate the indoor air When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat Fan 3 Set the fan speed Press the Fan lt or gt button on the remote control to set the desired fan speed When you press the Fan lt or gt button fan speed will change in order of Low Medium and High Z When you are using the remote control make sure correct indicator which matches your selection appears on the remote control display e Air flow can be adjusted manually See page 19 for instructions operating _17 HSIMONA operating basic function SELECTING OPERATION MODE Heat The air conditioner heats as well as cools Warm your room with this versatile appliance in the cold of winter 1 Turn on the air conditioner Press the Power button on the remote control 2 Set the operating mode Press the Mode button on the remote control until Heat set T
18. er radiator fins with extreme care e Wearing thick gloves can protect your hands Check for damages on the H Beam of the outdoor unit at least once a year The unit may fall down and there are potential risk of personal injury Check for damage on delivery If damaged do not install the air conditioner and call the place of purchase immediately Keep indoor temperatures stable and not extremely cold especially where there are children elderly or disabled people The packaging material and used batteries of the remote controller optional must be disposed of in accordance with the national standards The refrigerant used in the air conditioner must be treated as chemical waste Dispose the refrigerant following national standards When using a wireless remote control the distance should not be more than 7 meters from the air conditioner If the remote control is not used for a long period of time remove the batteries to prevent leakage of electrolyte The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Inspect the condition electric connections pipes and external case of the air conditioner regularly by a qualified service technician safety information _07 HSIONA safety information CAUTION SIGNS Do not open doors and windows in the room being cooled during operation unless nec
19. essary Do not block the air conditioner vents If objects block the air flow it may cause unit malfunction or poor performance Make sure that the condensed water dripping from the drain hose runs out properly and safely Firmly connect the drain hose to the air conditioner for proper water drainage Ensure the off on and protection switches are properly installed Do not use the air conditioner if damaged If problems occur immediately stop operation and disconnect the plug from the power supply If the air conditioner will not be used for an extended period of time for example over several months unplug the power from the wall Call the place of purchase or a contact center if repairs are needed e Potential risk of fire or electric shock if disassembly or repairs are attempted by a non qualified service technician 08_ safety information contents VIEWING YOUR AIR CONDITIONER OPERATING BASIC FUNCTION USING ADVANCED FUNCTIONS CLEANING AND MAINTAINING THE AIR CONDITIONER APPENDIX 10 10 10 tT 11 11 12 13 13 13 14 14 14 15 16 17 18 19 19 19 20 21 21 22 23 24 26 27 27 27 28 29 29 30 30 31 32 33 Checking the indoor unit and display Main parts Display Opening the front panel Power button and Room temperature sensor Checking the outdoor unit Checking the remote control Remote control dis play Using the remote control Inserting the batteries HSIONA Turning the
20. event electric shock Call the contact center for help SOHA Recommended instructions or useful information for use These warning signs are here to prevent injury to you and others Please follow them carefully After reading this section keep it in a safe place for future reference safety information _03 HSIONA safety information SEVERE WARNING SIGNS N Do not place the air conditioner near hazardous substances or equipment that releases free flames to avoid fire explosions or injuries e Potential risk of fire hazard or explosion Do not install the outdoor unit at an unstable place or elevated surface where there is potential risk of falling If the outdoor unit falls it may cause personal injury or loss or property Install the air conditioner away from direct exposure to sunlight heating apparatus and humid places e Hang curtains on windows to boost cooling efficiency and to avoid the risk of electric shock Any changes or modifications performed not following by the installation manual failure or damage may occur on the condition In this case user will be responsible for all the repair expenses Install an exclusive circuit breaker and short circuit breaker for the air conditioner e Potential risk of electric shock or fire Never use a damaged or dusted power plug power cable or loosened power receptacle e Potential risk of fire or electric shock Do not yank the power cab
21. for an extended period of time in ar oom with the door closed or with babies elderly or disabled people e Open the door or windows to ventilate your room at least once an hour to prevent oxygen shortage Do not connect the air conditioner with heating apparatus or attempt to disassemble remodel or repair it yourself e Potential risk of malfunction electric shock or fire If repairs are needed consult the contact center HSIMONA Consult the place of purchase or contact center to reinstall or disassemble the air conditioner e Improper installation carries a risk of unit malfunction water leakage electric shock or fire e Ifinstalling in specialty areas such as a factory complex or saline coastal area consult the place of purchase or contact center for specific installation details Consult a dealer regarding the appropriate measures to prevent the allowable concentration from being exceeded e If the refrigerant leaks and cause the concentration limit to be exceeded hazards due to lack of oxygen in the room may result Always make sure that the power supply is compliant with current safety standards Always install the air conditioner in compliance with current local safety standards Do not put undue stress or place heavy object on the power cable Do not bend the power cable excessively e Potential risk of fire or electric shock Use a rated circuit breaker only Never use steel wires or copper wires as a circu
22. ge to the air conditioner Do not open the front grille during operation e Potential risk of electric shock or unit malfunction Do not place any objects especially containers with liquid 06_ safety information Do not touch the pipe connected to the air conditioner Install the indoor unit away from lighting apparatus using the ballast e If you use the wireless remote control reception error may occur due to the ballast of the lighting apparatus Install the outdoor unit where operating noise and vibration will not disturb your neighbor and in a well ventilated area with no obstacle e Potential risk of malfunction e Operating noise may disturb your neighbor Make sure that there are no obstacles or covers that block the air conditioner Allow sufficient space for air circulation e Insufficient ventilation may result in poor performance If the power cable is damaged the manufacturer or a qualified service technician must replace it If a power outage occurs while the air conditioner is working turn off the power source immediately Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Have a qualified service technician install the air conditioner and perform a trial operation Make sure there are no obstacles under the indoor unit e Potential risk of fire or loss of property When cleaning the outdoor unit touch the heat exchang
23. he unit 2 Remove the Air filter Grab the handle and lift it up Then pull the Air filter towards you and slide it down 3 Slide the Bio filter color in sky blue out to remove it from the slot Bio filter can be placed in any 4 slots beneath the air filter 4 Clean the Bio filter with a vacuum cleaner or soft brush Then rinse it with running water and dry it in a ventilated area 5 Install the Bio filter back in position 6 Close the front panel i Clean the Bio filter every 3 months The cleaning term may differ on usage and environmental conditions 28_ cleaning and maintaining REPLACING THE FILTER Replacement filter may be purchased from the retail store or ordered from the dealer where you purchased the unit If you cannot find one please call a contact center Deodorizing filter Option Deodorizing filter absorbs efficiently cigarette smoke pet odors and other unpleasant smells Deodorizing filter cleaning is simple just remove old filter and install a new one 1 Open the front panel Tightly grab front side of the front panel and lift up the panel to open Then slightly push the panel up until the panel is hanged over the hooks ofthe unit HSIMONA
24. ie C mode indicator appears on the remote control display The air conditioner operates in Heat mode and warms your room K When you press the Mode button mode will change in order of Auto Cool Dry Fan and Heat 3 Set the temperature SET TEMP e Iia C Press the Temp A or V button on the remote control to increase or decrease the desired temperature You can set the desired temperature between the range of 16 C 30 C You can increase decrease the temperature by 1 C 4 Set the fan speed SET TEMP Press the Fan lt or button on the remote control to ae S set the desired fan speed If room temperature reaches desired value heating will stop for a while When you press the Fan lt or button fan speed will change in order of Auto Low Medium and High Fan may not operate for about 3 5 minutes at the beginning to prevent any cold blasts while the air conditioner is warming up Air flow can be adjusted manually See page 19 for instructions ig Since the air conditioner heats the room by taking heat energy from outdoor air the heating capacity may decrease when outdoor temperatures are extremely low If you feel the air conditioner insufficiently heats using an additional heating appliance in combination with the air conditioner is recommended 18_ operating ADJUSTING THE AIR FLOW DIRECTION Air flow c
25. it breaker It may cause fire or unit malfunctions If the indoor unit gets wet turn the power off immediately and call your nearest contact center e Potential risk of fire or electric shock To protect the product from water and possible shock you should keep the power cable and the connection cord of the indoor and outdoor units in the protection tube Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is sufficient to ensure the operation of any other domestic appliance connected to the same electric lines Disconnect the air conditioner from power supply before it is repaired or disassembled Clean the air conditioner after the inner fan stops operating e Potential risk of injury or electric shock safety information _05 safety information SEVERE WARNING SIGNS 5 Be sure to ground the unit Do not connect the ground wire to gas or water pipes lighting rods or telephone grounding lines e Ifthe unit is not properly grounded electric shock may result Use a receptacle that has a ground terminal The receptacle must be used exclusively for the air conditioner Improper electrical grounding may cause electric shock or fire If you smell burning plastic hear strange sounds or see smoke coming from the unit unplug the air conditioner immediately and call a contact center e Potential risk of fire or electric shock CAUTION SIGNS N
26. l and signs accordingly Make You should hear click sound pull up sure you have inserted the when the cover is locked batteries in correct position properly Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system viewing _13 operating basic function TURNING THE AIR CONDITIONER ON AND OFF Press the Power button on the remote control You will hear a beep and the air flow blade will move up and down automatically when the air conditioner is properly on The air conditioner will operate in the most recent operation mode used or Auto mode When you turn off the air conditioner air flow blade will stop moving and remain closed Z Turning on off your air conditioner without the remote control
27. le and touch the power plug with hands e Potential risk of fire or electric shock Do not cut the power plug and connect to a different power cable Turn off the air conditioner using the provided remote control or control accessory if provided Do not unplug to turn off the unit unless there is an immediate danger Do not insert anything such as fingers or branches into the air conditioner vents when the air conditioner is running e Keep children away from the air conditioner not to put their figures Potential risk of personal injury Ensure no water gets into the air conditioner e Potential risk or electric shock e If the water gets into the air conditioner stop and turn off the power source immediately Do not insert anything such as fingers or branches into the air inlet or outlet of the unit e Keep children away from the air conditioner Potential risk of personal injury The air conditioner is composed of moving parts Keep children away from the unit to avoid physical injury Make sure that children take precautions against access to the air conditioner and they do not play with the unit 04_ safety information N p Do not clean the interior of air conditioner on your own e Consult the place of purchase or contact center before cleaning the interior of air conditioner The wrong way of cleaning may damage or defective electric parts and cause electric shock or fire Do not run the air conditioner
28. n take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal contents _09 viewing your air conditioner Congratulations on the purchase of the air conditioner We hope you enjoy the features of your air conditioner and stay cool or warm with optimal efficiency Please read the user manual to get started and to make the best use of the air conditioner CHECKING THE INDOOR UNIT AND DISPLAY Carefully unpack your air conditioner and check the unit to make sure it is not damaged Main parts Air filter under the panel Z Air intake Air flow blade SEn up and Gown Blade pin lever Air flow blade left and right Display Q Your air conditioner may slightly look different from illustration shown above depending on your model 10_ viewing OPENING THE FRONT PANEL Tightly grab front side of the front panel and lift up the panel to open Then slightly push the panel up until the panel is hanged over the hooks of the unit HSIIONA Power button and Room temperature sensor You may locate the Power button on the right bottom side of the air conditioner If the front panel is open you can check
29. n the remote control to change the time setting while On timer indicator is blinking You can set the time up to 24 hours increasing in 30 minute unit up to first 3 hours and in hourly unit after first 3 hours 3 Pressthe Set Cancel button on the remote control to active it on The remote control display will show the hour s you have set for 3 seconds and set desired temperature will display The air conditioner will operate automatically at set time and then On timer indicator stops blinking and stays on If On timer is not set within 10 seconds the air conditioner will end setting 4 Set the operating mode i SET aa Press the Mode button on the remote control until the 1 Lf c desired mode appears on the remote control display The air conditioner will operate in the mode you set IZ On timer function is available in Auto Cool Dry Fan Heat mode IZ Temperature can also be adjusted See step 3 on page 14 for instructions After the set up while the unit is off approximately after 10 seconds all the other indicators will be gone except the On timer indicator Time setting can be changed by pressing the On Timer button Press the On Timer button to change time setting and then press the Set Cancel button to active it on To deactivate the On timer 1 Pressthe Set Cancel button on the remote control On timer you set will be canceled and On timer indicator will disapp e
30. nsert the power plug into the wall socket correctly Check if the circuit breaker is switched off e Check if there is a power failure e Check your fuse Make sure it is not blown out The temperature does not change e Check if you selected Fan mode Press the Mode button on the remote control to select another mode The cool warm air does not come out of the air conditioner e Check if the set temperature is higher lower than the current temperature Press the Temp A or V button on the remote control to change the set temperature Press the Temp A or V button to increase or decrease the temperature e Check if the air filter is blocked by dirt Clean the Air filter every tw o weeks Check if the air conditioner has just been turned on If so wait 3 minutes The fan speed does not change e Check if you selected Auto or Dry mode The air conditioner automatically adjusts the fan speed to Auto in A uto Dry mode Timer function does not set e Check if you pressthe Set Cancel button on the remote control after you have set the time Odors permeate in the room during operation Check if the appliance is running in a smoky area or if there is a smell entering from outside Operate the air conditioner in Fan mode or open the windows to air out the room The air conditioner makes a bubbling sound A bubbling sound may be heard when the refrigerant is circulating through the compresso
31. nutes and then operates in last used mode or in Auto mode if Dry Fan mode is most recent mode used l4 Turbo function is only available in Auto Cool Heat mode If Turbo function is selected in Dry Fan mode operating mode changes to Auto To deactivate Turbo function 1 Pressthe Turbo x button on the remote control again The air conditioner operates in last used mode or in Auto mode if Dry Fan mode is most recent mode used l4 e When you are using the remote control make sure corresponding indicator appears on the remote control display Temperature Fan speed cannot be adjusted while using this function e Air flow can be adjusted manually See page 19 for instructions e When the Turbo function is activated pressing Mode button will automatically cancel the function 20_ using advanced functions SETTING TIMER This advanced Timer function allows you to turn on off your air conditioner automatically even when you are away Simply set the time and your air conditioner will turn on off automatically On timer This function allows you to turn on the air conditioner automatically within the time range of 24 hours On timer is available while your air conditioner is on off 1 Pressthe On Timer button on the remote control HSIIONA On timer indicator blinks on the remote control display 2 Set the time you want the air conditioner to turn on automatically Press the On Timer button o
32. r Let the air conditioner operate in a selected mode Water is dripping from the air flow blades e Check if the air conditioner has been cooling for an extended period of time with the air flow blades pointed downwards Condensation may generate due to the difference in temperature Remote control is not working e Check if your batteries are depleted e Make sure batteries are correctly installed e Make sure nothing is blocking your remote control sensor e Check that there are strong lighting apparatus near the air conditioner Strong light which comes from fluorescent bulbs or neon signs may interrupt the electric waves 32_ appendix OPERATION RANGES The table below indicates the temperature and humidity ranges the air conditioner can be operated within Refer to the table for efficient use MODE OPERATIONAL TEMPERATURE INDOOR OUTDOOR INDOOR HUMIDITY IF OUT OF CONDITIONS COOLING 18 C to 32 C 15 C to 43 C 80 or less Condensation may occur on the indoor unit with risk to have either water blow off or drops on the floor HEATING 27 C or less 5 C to 24 C Internal protection triggers and the air conditioner will stop DRYING 18 C to 32 C 15 C to 43 C Condensation may occur on the indoor unit with risk to have either water blow off or drops on the floor K The standardized temperature for heating is 7 C If the ou
33. t a comfortable sleep temperature while saving energy and having sound sleep For easy future reference write the model and serial number Model down You will find your model number on the bottom side of the air conditioner 02_ features Serial safety information To prevent electric shock disconnect the power before servicing cleaning and installing the unit SAFETY INFORMATION Before using your new air conditioner please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Because the following operating instructions cover various models the characteristics of your air conditioner may differ slightly from those described in this manual If you have questions call your nearest contact center or find help and information online at www samsung com What the icons and signs in this user manual mean Risk of death or serious personal injury WARNING gt Potential risk of personal injury or material damage Q gt O Z gt To reduce the risk of fire explosion electric shock or personal injury when using your air conditioner follow these basic safety instructions Q gt O zZ Do NOT attempt Do NOT disassemble Do NOT touch Follow directions carefully Unplug the power plug from the wall socket Make sure the machine is grounded to pr
34. tdoor temperature drops to 0 C or below the heating capacity can be reduced depending on the temperature condition If the cooling operation is used at over 32 C indoor temperature it does not cool at its full capacity appendix _33 HSIONA Contact SAMSUNG WORLD WIDE If you have any comments orquestions regarding a Samsung product contact the SAMSUNG customer care center Customer Care Center Web Site Samsung Electronics Co Ltd All Rights Reserved
35. the room temperature sensor You can turn on the air conditioner without the remote control by pressing the Power l button The room temperature sensor measures indoor room temperature Room temperature sensor D C gt power button CHECKING THE OUTDOOR UNIT AQO7RLX AQO9RLX AQO9ULX AQ12ULX AQ18ULX Air Inlet Rear Air Inlet Rear Connection Valve A Connection Valve Air Outlet Air Outlet viewing _11 viewing your air conditioner CHECKING THE REMOTE CONTROL You can activate the air conditioner by pointing the remote control away from it When using the remote control always point it directly at the air conditioner Remote Control display Power Turn on off the air conditioner Mode Set one of the 5 operating modes See pages 14 18 for instructions Fanspeed lt Adjust how much air flows through the air conditioner with the 4 different fan speeds such as Auto Low Medium High Smart Saver Less energy usage makes your space cool between the temperature range of 26 C 30 C On Timer Set the On Timer on Adjust the timer for on timer K 12_ viewing E a eS A Temp lt Fan Temp Y Smart Saver good sleep Set On Off Timer Timer Cancel A VSL ae Turbo wre Operate in maximum fan speed to cool warm quickly Air swing Activate Deactivate air flow blade movement automatically up and down Temp AV In
36. to wake up from comfortable intermittent air and it makes you feel refresh Set Off timer in good sleep mode over 5 hours You feel disturbed sleep if the good sleep is set too short or long because the default is set to 8 hour operation If the good sleep mode is set less than 4 hours the operation will stop at the set time If the good sleep mode is set over 5 hours it will run as Wake up stage for the last one hour before stop e Recommended set temperature is between 25 C 27 C for cooling and 21 C 23 C for heating Cool mode Set temperature When the set time is over 8 hours this section will be repeated 1 2 3 4 5 6 7 8 Time hr Heat mode I When the set time is over 8 hours this section will be repeated r Set temperature 1 2 3 4 5 6 7 8 Time hr To deactivate good sleep mode 1 Pressthe Set Cancel button on the remote control good sleep mode you set will be canceled and good sleep indicator will disappear using advanced functions HSIMONA using advanced functions USING THE SMART SAVER FUNCTION This function will set the temperature range limit to help you save energy while the air conditioner is operating in Cool mode 1 Pressthe SmartSaver button onthe remote control while the air conditioner is operating in Cool mode Smart Saver indicator and air swing indicator appears automatically on the remote control display The air flow blades move up and down
37. ystem This internal protection operates if an internal fault occurs in the air conditioner Type Description Against cold air The internal fan will be off to against cold air when the heat pump is heating De ice cycle The internal fan will be off to against cold air when the heat pump is heating Anti protection of internal battery HSIONA The compressor will be off to protect internal battery when the air conditioner operates in Cool mode Protect compressor The air conditioner does not start operating immediately to protect the compressor of the outdoor unit after it has been started Z If the heat pump is operating in Heat mode De ice cycle is actuate d to remove frost from an outdoor unit that may have deposited at low temperatures The internal fan is switched off automatically and restarted only after the de ice cycle is completed cleaning and maintaining _31 appendix TROUBLESHOOTING Refer to the following chart if the air conditioner operates abnormal ly This may save time and unnecessary expenses PROBLEM SOLUTION The air conditioner does not operate immediately after it has been restarted Because of the protective mechanism the appliance does not start operating immediately to keep the unit from overloading The air conditioner will start in 3 minutes The air conditioner does not work at all e Check that the power plug is properly connected I
Download Pdf Manuals
Related Search