Samsung VC-7716V Керівництво користувача
Contents
1. 1 22. gt ANA
3. y ry STOP
4. 2 3 DJ68 00079H REV 0 3
5. 1 2 lt lt gt gt 3 2 5 4
6. gt 5 3 4 1 Ni wa
7. 2 1 2 3 4 ina
8. MIN 2 1 2 4 3 4 1
9. e 2 e e 6 e O
10. Instructions Before operating this unit please read the instructions carefully IMPORTANT SAFEGUARDS gt This appliance must be connected to the same voltage of electrical power supply as shown on your vacuum cleaner s rating plate Do not use your vacuum cleaner on a wet surface It cannot be used to remove liquids Carpets treated with a liquid cleaner must be allowed to dry before being cleaned with the unit gt Never operate the vacuum cleaner without a dust bag dust bag is not inserted the cover cannot be closed please don t close forcibly Keep children away from your vacuum cleaner It must not be used on people or animals gt Never use your vacuum cleaner to vacuum matches glowing embers or cigarette ends Avoid vacuuming hard pointed objects since they may damage the appliance or dust bag Consult the trouble shooting guide in this manual if your vacuum cleaner fails to operate properly Contact an authorized service agent if the problem persists If the main cable is defective the complete cable winder must be replaced by a service agent Don t use your vacuum cleaner outdoors When you have unpacked the unit do not simply throw the packing into the household waste gt Take them to an appropriate collecting points for the recycling IDENTIFICATION OF PARTS HANDLE POWER CONTROL ca ONLY HANDLE CONTROL TYPE AIR REGULATOR
11. you can either open hose connection cover press On off button or unplug the plug USING THE ACCESSORIES Press the tool storage cover downward Crevice tool for radiators crevice corners between cushions Upholstery brush for cushions and drapery Dusting brush for furniture shelves books etc DUSTING POLSTERDUSTELE Before use assemble the dusting brush to the crevice tool PARK POSITION Located in the top rear side of the vacuum cieaner there is a nozzle support that can be used to park the nozzle during pauses in cleaning TRANSPORATING AND STORING THE VACUUM CLEANER For easy storage and transportation this vacuum cleaner has a clip system built into the body which will keep the tube hose and nozzle in a vertical position REPLACING THE DUST BAG 1 To open the dust cover of the dust bag 2 Remove the carrying bag from the cleaner compartment press the clamper upward The clamper is located at the front of the dust cover CARRYING BAG 3 After removing the used dust bag insert the 4 Press the dust cover down gently until the cardboard bag collar of the new dust bag clamper relocks into the carrying bag Used dust bag can be sealed by removing the film from the paper _ and sticking the latter over the suction opening ONLY PAPER BAG FOR CLOTH FILTER BAG After using if the cloth filter bag is full of dust clean the cloth filter ba
12. HANDLE SUCTION HOSE BUTTON FOR SUCTION DUST FULL INDICATOR HOSE REMOVAL FOR BLOWING CORD REWIND BUTTON POWER CONTROL SWITCH MITE KILLER LAMP ON OFF SWITCH RUG FLOOR FLOOR NOZZLE SELECTOR BUTTON FOR SUCTION HOSE REMOVAL FOR USING THE MITE KILLER Features marked may vary according to model HANDLE CONTROL OPERATION ONLY HANDLE CONTROL TYPE The suction capacity can be regulated steplessly by moving the side A to the desired position SLIDE IN THE STOP POSITION Vacuum cleaner switches off stand by mode SLIDE TOWARDS MAX Suction capacity increases steplessly up to max POWER CONTROL ONLY SLIDING REGULATOR TYPE Vacuuming power can be adjusted to suit different situations using the power control MIN For delicate fabrics like curtains MAX For hard floors and heavily soiled carpets 2 DUST FULL INDICATOR If the Dust Full indicator switches to RED while you are cleaning the dust tbag requires replacement the Dust Full indicator continues to display RED even after changing the dust bag turn the cleaner off to see if the hose tube or nozzle is clogged ASSEMBLING THE VACUUM CLEANER READY FOR USE 1 Connect the suction hose to the suction 2 Connect the suction tubes together tube depending on model Adjusting the telescopic tube depending on model 3 Connect the nozzle to the suction tube at Co
13. g and use it again MAINTENANCE OR REPLACEMENT OF THE FILTERS 1 INLET FILTER Open the dust cover GRILLE FILTER After detaching the filter wash it lightly with water dry it in the shade and then insert it in its original position OUTLET Close the dust cover FILTER INLET FILTER 2 OUTLET FILTER The outlet filter which the air comes out from the vacuum cleaner Open the dust cover and then pull the hook upward located at the front of the grille filter Remove and replace the exhausted outlet filter Close the grille filter and then close the dust cover 6 RUG FLOOR SELECTOR Before use make sure that the position of the selector button is in the right position for the type of surface to be cleaned In order to maintain best cleaning efficiency clean floor brush using crevice tool after use Push to side when cleaning the carpets Push to side when cleaning the floor tile mat etc TROUBLE OOTING Suction force is as Filter nozzle suction hose decreasing or tube is blocked Check that the cord isnot Pull the cord out 2 3m amp push twisted or wound unevenly down the cord rewind button Remove the object Cord does not rewind se This Vacuum cleaner is approved the following EMC Directive 89 336 EEC 92 31 EEC and 93 68 EEC Low Voltage Safety Directive 73 23 EEC and 93 68 EEC 7 DJ68 00079H REV 0 3 LBI
14. nnect the connector to the body of the cleaner POWER CORD 1 PULLING OUT The long power cord can be drawn out for your convenience 2 REWINDING After disconnecting the plug from the electrical outlet press the cord rewind button lightly with your toe The cord will automaticaly rewind ON OFF SWITCH You can start or stop your vacuum cleaner by pressing the on off switch lightly with your toe USING THE BLOWER EXCEPT HANDLE CONTROL i blow out dust in crevice or comers you can use this function for your convenience Located on the rear side of the cleaner 1 Disconnect the hose clamper from the 2 Open the tool storage cover body of the cleaner 3 Remove the blow hole cap from the 4 Connect the hose clamper to the blow body of the cleaner hole pre Don t use your vacuum cleaner outdoors USING THE MITE KILLER OPTIONAL 1 Disconnect the body connector from the body of the cleaner 2 Shut the hose connection cover until tone is heard Your vacuum cleaner is not malfuctioning if it starts to operate when the hose connec tion cover is closed This will happen if the HOSE CONNECTION COVER vacuum cleaner was on when the hose was removed 3 Mite killer lamp on Insect and germ killing work is started it will continue for 2 to 5min the process stops automatically MITE KILLER LAMP 4 If you want to stop the machine while operat ing
15. no gt
Download Pdf Manuals
Related Search