Home

Samsung AR09HSFSPWKN Lietotāja rokasgrāmata

1. PS a UE This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance For use in Europe This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision NOILYHVd34d LO FOR CLEANING WARNING Do not clean the appliance by spraying water directly onto it Do not use benzene thinner or alcohol to clean the appliance This may result in discoloration deformation damage electric shock or fire Before cleaning or performing maintenance cut off the power supply and wait until the fan stops gt Failing to do so may result in electric shock or fire FORCLEANING ACAUTION Take care when cleaning the surface of the heat exchanger of the outdoor unit since it has sharp edges This should be done by a qualified technician please contact your instal
2. 010005 176A47 271920 37C63F 010005 156A69 272328 37C83F The original software version used for the product range is identified in this manual For the software version issued at the time of manufacture please refer to the mark plate of the indoor and outdoor units The mark plate can be physically located on the side of both the indoor Temperature display side and outdoor units Compressor side In addition for the current software version of the air conditioner Wi Fi control application please refer to the front screen of the application itself English 4 A3050 EE Good IB amp IM_DB68 05270A 01_EN Immm indd 4 2015 6 15 17 57 33 Outdoor unit ARO9HSFSPWKXEE AR12HSFSPWKXEE Dimension Unit WidthxHeightxDepth 790x548x285 Weight Unit 35 5 Fan Air flow rate Cooling High Low 35 0 10 0 Heating High Low 35 0 10 0 Sound power Cooling High Sound pressure Cooling High Heating High Operation range Cooling Ambient Min Max 15 46 Heating Ambient Min Max 25 24 Refrigerant Type Charge Add charge after 10m R 410A 1 2 0 015 Lenght OD ID Std Max 5 15 Level difference ID OD Max 8 Phase Frequency Voltage 1 50 220 240 Maximum Fuse amps MFA 15 Type ROTARY BLDC Expansion Device Type Step EEV 480 Motor Type Output W
3. Installing and connecting the assembly pipe of the indoor unit Assembling the hanger screw and guide 1 Cut outthe knock out piece according to the drain hose direction before fixing the indoor unit Left and right each has one 2 Fixthe indoor unit on the wall KO OUR Pass the cables pipes and hose through the hole which would be connected to the outdoor unit 3 Use 2 screws to fix the indoor unit as shown in the picture 4 Assemble the Guide into the position where the knock out piece has been cut out before There re three hooks on the Guide they must be totally fixed to the unit The method of assembling the Guide is same whether it s on right or on left Evacuating the indoor unit The indoor unit is supplied with inert gas nitrogen Before installing the unit check if nitrogen gas flow out of indoor unit If this one isn t true DO NOT INSTALL THE UNIT since leakage could be inside the indoor unit Unscrew the caps at the end of each pipe gt All inert gas exhausts from the indoor unit To prevent dirt or foreign substances from getting into the pipes during note installation do NOT remove the caps completely until you are ready to connect the pipes The remaining air in the Refrigeration cycle which contains moisture may cause malfunction on the compressor Always contact the service center or a professional installation agency for product installation CAUTION Pi
4. Underside_right C Rear_right or left D i g 5 E 1 Disassemble the cover panel as described in page 43 45 2 Remove the Hanger plate from the indoor unit 1 Unscrew 2 screws that fixes the Hanger plate to the indoor unit 2 Push the hooks on the bottom part of the indoor unit up to release the installation plate from the hooks that holds it 3 Pull the installation plate to release it completely from the indoor unit ER 7 p Y SAUT AN 3 Determine the position of the pipe and drain hose hole as seen in the picture and drill the hole with an inner diameter of 65 mm so that it slants slightly downwards AR12HSFSPWKNEE Pipe hole 65 mm Unit mm fi Model A B C D ARO9HSFSPWKNEE 36 190 81 36 A Make sure to drill only one hole after choosing Gurion the direction of the pipe 4 Fix the indoor unit If you fix the indoor unit on a wall Ea 1 Fix the installation plate to the wall giving attention to the weight of the indoor unit Plastic 4 If A A Anchor 7 B Ifyou mount the plate to a concrete wall using plastic anchors make sure that gaps 5 7 Wall nore between the wall and the plate created by projected anchor is less than 20mm em ts ve If you fix the indoor unit on a window frame If you fix the indoor unit on a gypsum board
5. A3050 EE Good IB amp IM_DB68 05270A_EN indd 1 2015 4 3 11 42 31 ZS a NE Features of your new air conditioner I 2 step cooling 2 step cooling function will quickly cool the room to reach the set temperature and then it will adjust the fan speed and air flow direction automatically to help you stay comfortable and refreshing Fast cooling heating If you want the strong and cool warm air just select Fast function It will get you the strongest air I Comfort cooling heating If you want the comfortable and refreshing air Comfort function will spread the cool warm air indirectly to you so that you can stay comfortable I Single User Use Single User function when you are alone at home Single User function will minimize the energy consumption with inverter technology and reduce your electricity bill by adjusting the maximum operating capacity of the compressor Easy Filter There is no grille to remove before separating the filter from the air conditioner Therefore filter can be cleaned easily more frequently Frequent filter cleaning will prevent dust from entering into the product or accumulating on the filter I good sleep function good sleep function will allow you to have deep good night s sleep by adjusting the temperature fan speed and air flow direction Smart Install When the installation is done your product will examine itself through trial operation to check if it was install
6. ZS Soe A3050 EE Good IB amp IM_DB68 05270A_EN indd 15 2015 4 3 11 42 33 ZS CON NE Basic function Basic operation is an operation mode that can be selected by pressing the Mode button Auto 2 Step Cooling or Heat In Auto mode the air conditioner will automatically set the temperature and fan speed depending on the room temperature 2 Step Cooling mode sets the air conditioner to operate in Fast Cool mode when set temperature is lower than indoor temperature and then the air conditioner will automatically operate in Dry mode when indoor temperature reaches set temperature Cool In Cool mode the air conditioner will cool your room You can adjust the temperature and the fan speed to feel cooler in hot season If current outside temperature is much higher than the selected indoor temperature it may take time to bring the inner temperature to the desired coolness Quiet mode makes the noise quieter during the operation of the indoor unit in the Cool mode Dry The air conditioner in Dry mode acts like a dehumidifier by removing moisture from the indoor air Dry mode makes the air feel refreshing in a humid climate To activate the Dry mode set temperature on the remote controller should be lower than indoor room temperature Fan Fan mode can be selected to circulate your room Fan mode will be helpful to refresh the stale air in your room Heat In heating mode the air con
7. gt Ifthe outdoor unit falls it may result in injury death or property damage This appliance must be properly grounded Do not ground the appliance to a gas pipe plastic water pipe or telephone line gt Failure to do so may result in electric shock fire and explosion gt Make sure to use a socket outlet with ground NOILYHVd34d LO FOR INSTALLATION CAUTION Install your appliance on a level and hard floor that can support its weight Failing to do so may result in abnormal vibrations noise or problems with the product Install the draining hose properly so that water is drained correctly gt Failing to do so may result in water overflowing and property damage Avoid adding drain to waste pipes as odours may arise in the future When installing the outdoor unit make sure to connect the draining hose so that draining is performed correctly D The water generated during the heating operation by the outdoor unit may overflow and result in property damage In particular in winter if a block of ice falls it may result in injury death or property damage FOR POWER SUPPLY A WARNING When the circuit breaker is damaged contact your nearest service center Do not pull or excessively bend the power line Do not twist or tie the power line Do not hook the power line over a metal object place a heavy object on the power line insert the power line between objects or push the power line into the space
8. DC 40 Base heater Type Output W SHEATH 150 Software version A3050 EE Good IB amp IM_DB68 05270A 01_EN Immm indd 5 Main Code Version DB91 01615A 140401 Inv Code Version DB91 01517A 130705 EEProm Code Version English 5 DB82 02051A 140401 DB82 02052A 140401 2015 6 15 17 59 38 CURE Safety precautions Before using your new air conditioner please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Because the following operating instructions cover various models the characteristics of your air conditioner may differ slightly from those described in this manual If you have any questions call your nearest contact center or find help and information online at www samsung com Important safety symbols and precautions Hazards or unsafe practices that may result in severe A WARNING personal injury or death Hazards or unsafe practices that may result in minor N CAUTION personal injury or property damage Follow directions Cut offthe power supply Do NOT attempt Do NOT disassemble Make sure the machine is grounded to prevent electric shock FOR INSTALLATION A WARNING Q Use the power line with the power specifications of the product or higher and use the power line for thi
9. When the On timer is set while the air conditioner is off Timer indicator K will be displayed and remain on until the On timer turns on Off timer may not work depending on the On Off status of the indoor unit and the On Off status of the indicator on the remote controller display Only the latest setting timer will be applied between the On Timer Off Timer and good sleep Off timer functions Remote controller display English 20 A3050 EE Good IB amp IM_DB68 05270A_EN indd 20 2015 4 3 11 42 35 Additional options available in On Off timer mode When the remote controller is on You can select from Auto Cool Dry Fan Heat Temp YAWIL 0 You can set the temperature after selecting the operation mode Temperature adjustment is available when Auto Cool Dry Heat mode is selected Setting on timer and off timer simultaneously Follow the same process for setting on timer and off timer Remote controller display Ontimer and Off timer setting time should be different from each other NOTE Press the Power button on the remote controller while timer combination is on Both of the On and Off timer will be canceled and the indicator will disappear English 21 A3050 EE Good IB amp IM_DB68 05270A_EN indd 21 2015 4 3 11 42 36 ZS CSN EU good sleep mode For a comfortable sleep the air conditioner will operate in 3 stages in order of Fall asleep
10. from the outdoor defrost operation from outdoor heat exchanger during Heat unit mode in winter Water is dropping Water may be generated because of the temperature from the outdoor difference It is normal unit piping connection English 35 SY3HLO 90 2015 4 3 11 42 42 Safety precautions Carefully follow the precautions listed below because they are essential to guarantee the safety of the equipment Always disconnect the air conditioner from the power supply before servicing it or accessing its internal components Verify that installation and testing operations are performed by qualified personnel Verify that the air conditioner is not installed in an easily accessible area General information gt Carefully read the content of this manual before installing the air conditioner and store the manual in a safe place in order to be able to use it as reference after installation For maximum safety installers should always carefully read the following warnings Store the operation and installation manual in a safe location and remember to hand it over to the new owner if the air conditioner is sold or transferred This manual explains how to install an indoor unit with a split system with two SAMSUNG units The use of other types of units with different control systems may damage the units and invalidate the warranty The manufacturer shall not be responsible for damages arising from the use of non
11. installation Connect the wires firmly so that wires can not be pulled out easily If they are loose it could cause burn out of the wires Connect the wires according to color codes referring to the wiring diagram The power cable and the interconnection cable should be selected according to the specification in page 45 English 46 A3050 EE Good IB amp IM_DB68 05270A_EN indd 46 2015 4 3 11 42 48 Installing and connecting the assembly pipe of the indoor unit Connect indoor and outdoor units with field supplied copper pipes by means offlare connections Use insulated seamless refrigeration grade pipe only Cu DHP type according to IS01337 degreased and deoxidized suitable for operating pressures of at least 4200 kPa and for burst pressure of at least 20700 kPa Under no circumstances must sanitary type copper pipe be used There are 2 refrigerant pipes of different diameters The smaller one is for the liquid refrigerant The larger one is for the gas refrigerant A short pipe is already fitted to the air conditioner You may need to extend the pipe using the assembly pipe optional NOILVTIVISNI ZO The connection procedure for the refrigerant pipe varies according to the exit position of the pipe when facing the wall Right A Left B Underside C Rear i i Torque 1 Cut out the appropriate knock out piece A or B on the rear of the Oute
12. 05270A_EN indd 51 2015 4 3 11 42 50 ZS a EU Installing and connecting the drain hose of the indoor unit 20mm 20mm 40 45 mm or more or more 7 4 IS Drain hose Extension F Extension drain hose Drain hose drain hose VinylTape Foam Insulation 6 Pass the drain hose under the refrigerant pipe keeping the drain hose tight 7 Pass the drain hose through the hole in the wall Check if it slants Shield downwards as seen in the picture a O a REN 8 Using natural drainage method check the drainage is normal LEE a x 2 F Drain hose Extension drain hose The hose will be fixed permanently into position after finishing the installation and the gas leak test refer to page 57 for further details Make sure the installed direction of the drain hose is correct Inadequate installation may cause condensate water leakage Ifthe drain hose is routed inside the room insulate the hose so that dripping condensation does not damage the furniture or floors DO NOT WALL UP THE DRAIN HOSE CONNECTION Drain hose connection must be easy accessible and serviceable Changing direction of the drain hose Change the direction only when it is necessary 1 Detach the rubber cap with the pliers 2 Detach the drain hose by pulling it and turning to the right 3 Insert the drain hose by fixing it with the screw into the groove of the drain hose and the outlet o
13. Address Product Information Data can be found on the product mark plates Model Code Outdoor Serial Number Software Version Model Code Indoor Serial Number Software Version Installation Information Date of Installation Location Address Installation Company Name Installation Company Address Recommended Installation Guidance On the behalf of the customer Yes No Has the customer been provided guidance regarding the maintenance of the roduct Has the customer been provided guidance regarding the operation ofthe roduct In order to ensure the correct installation and operation of this product it is recommended that a service visit be arranged within a reasonable period of time In the event of a service issue please refer to the troubleshooting guide of the relevant supporting manuals It is recommended that a skilled service technician be contacted for support Should urgent support be required then using the information provided contact the local Samsung office via email or telephone so that support can be initiated via our approved service centres ASC S within 24hrs It is also recommended that the product be registered with the manufacturer shortly after the date of installation Please register your product at the following location www samsung com warranty QUESTIONS OR COMMENTS COUNTRY CAL
14. Outdoor temperature sensor error Outdoor Coil temperature sensor error Discharge temperature sensor error Discharge over temperature EEV or Valve Close error Self diagnosis O Q E554 E440 E441 E458 Gas Leak error Out of the Limit of the operation Outdoor temperature OO Fan error Outdoor Compressor starting error Compressor trip error PFC over current IPM over current O C Compressor V limit error 1018 018 8 1000100 DC Link voltage under over error Compressor rotation error comp wire missing error Current sensor error 0 0 0010 DC Link voltage sensor error EEPROM error Outdoor OTP error AC line zero cross signal error Heat Sink sensor error H W DC Link over PFC over load Input current sensor error Heat Sink overheat error Capacity miss match error English 62 A3050 EE Good IB amp IM_DB68 05270A_EN indd 62 2015 4 3 11 42 54 A3050 EE Good IB amp IM_DB68 05270A_EN indd 63 2015 4 3 11 42 54 Record of Installation It is recommended that your receipt be stapled to this page for proof of purchase date and or for warranty purposes should it be required Please ensure that the following information is recorded once the installation has been completed Purchase Information Date of Purchase Dealer Company Name Dealer Company
15. Tightening torque for body cap gt Before inspecting the leakage use a torque wrench Refer to the table to close the cap for the service valve Comply witha tightening torque for each size of the diameter and i tighten the cap firmly to prevent any leakage gt To check for any possible leakage insert inert gas into Spindle the pipes connected to indoor outdoor units and check the connection part of the indoor outdoor units Charging 7 fe with soap lather or liquid for leakage test core Lt 7 Outer Tightening torque cea Body cap Nm Charging port cap A Nem R 22 Diameter of the screw 7 16 20UNF 9 6 35 20 25 R 410A Diameter of the screw 1 2 20UNF D 0952 20 25 amp 012 70 25 30 10 12 Tightening torque for charging port cap u Refer to the table 15 88 AA 019 05 35 40 To check for gas leaks on the outdoor unit 1 Nm 10 kgfcm Check the valve A and B using a leak detector To check for gas leaks on the indoor unit Check the flare nut C and D using a leak detector Leak test with nitrogen before opening valves In order to detect basic refrigerant leaks before recreating the vacuum and recirculating the R 410A it s responsible of installer to pressurize the whole system with nitrogen using a cylinder with pressure reducer at a pressure above 40 bar gauge Leak test with R 410A after opening valves Before opening valves discharge all the nitrogen from the system and cre
16. _ i The terminal There is no ring terminalto L Upside down socketis damaged cover the wire gt There must be no space between the terminal and the screw when connected Any remaining space may become a fire hazard due to overheating of the electrical contact i i i Either the screw is not fitted propery or there is a space The terminal socket between the screw and the is upside down ring terminal For the terminal block wiring use a wire with a ring terminal socket only Regular wires without a ring terminal socket may become a fire hazard due to overheating of the electrical GAUTION contact during a wiring work 3 When you install the unit make first refrigerant connections and then electrical connections Connect the air conditioner to grounding system before performing the electrical connection If unit is uninstalled first disconnect electrical cables then refrigerant connections If the outdoor unit is more than 5 5 meters away from the indoor unit you must extend the cable The maximum length of the cable is 15 meters 1 Extend the assembly cable if necessary N Do not connect two or more different cables to extend the length It may cause fire CAUTION English 45 A3050 EE Good IB amp IM_DB68 05270A_EN indd 45 2015 4 3 11 42 48 Zo CON NE Connecting the assembly cable 2 Open the cover panel 3 Remove the screw securing the connector cover 4 P
17. at support Only for Dealers 0810 112233 SWITZERLAND 0800 726 78 64 0800 SAMSUNG or cia 300 SAMSUNG 800 726786 www samsung com cz support CROATIA 072 726 786 www samsung com hr support BOSNIA 055 233 999 www samsung com support MONTENEGRO 020 405 888 www samsung com support 080 697 267 brezpla na tevilka SLOVENIA 090 726 786 0 39 EUR min www samsung com si klicni center vam je na voljo od ponedeljka do petka od 9 do 18 ure SERBIA 011 321 6899 www samsung com rs support BULGARIA 800 111 31 BesnnatHa TeneboHHa rnuHUA www samsung com bg support ROMANIA 08008 726 7a 6A CaaS AMSUNG www samsung com ro support CYPRUS 8009 4000 only from landline toll free GREECE 80111 SAMSUNG 80111 726 7864 only from land line www samsung com gr support 30 210 6897691 from mobile and land line LITHUANIA 8 800 77777 www samsung com lt support LATVIA 8000 7267 www samsung com lv support ESTONIA 800 7267 www samsung com ee support DB68 05270A 03 A3050 EE Good IB amp IM_DB68 05270A 01_EN indd 64 amp 2015 6 5 16 23 32 ARO9HSFSPWK EE AR12HSFSPWK EE 100 Recycled Paper imagine the possibilities Thank you for purchasing this Samsung product a A3050 EE Good IB amp IM_DB68 05270A_EN indd 65 2015 4 3 11 42 54
18. behind the appliance This may result in electric shock or fire English 7 A3050 EE Good IB amp IM_DB68 05270A_EN indd 7 2015 4 3 11 42 32 Mo A LUE Safety precautions FOR POWER SUPPLY A CAUTION When not using the air conditioner for a long period of time or during a thunder lightning storm cut the power at the circuit breaker gt Failing to do so may result in electric shock or fire FOR USING A WARNING Ifthe appliance is flooded please contact your nearest service center gt Failing to do so may result in electric shock or fire If the appliance generates a strange noise a burning smell or smoke cut off the power supply immediately and contact the nearest service center gt Failing to do so may result in electric shock or fire In the event of a gas leak such as propane gas LP gas etc ventilate immediately without touching the power line Do not touch the appliance or power line gt Do not use a ventilating fan gt A spark may result in an explosion or fire To reinstall the air conditioner please contact your nearest service center gt Failing to do so may result in problems with the product water leakage electric shock or fire gt A delivery service for the product is not provided If you reinstall the product in another location additional construction expenses and an installation fee will be charged gt Especially when you wish to install the product
19. by the wall 300 or more NOILYTIYLSNI ZO Unit mm When 3 sides of the outdoor unit are E gt E 150 or more 600 or more The upper part of the outdoor unitand The upper part ofthe outdoor unitand amp When the walls are blocking front and the rear side of the outdoor unit the air outlet is towards the wall the air outlet is opposite the wall 8 300 or more 2000 or more 5 u A a English 39 A3050 EE Good IB amp IM_DB68 05270A_EN indd 39 300 or more 1500 or more 2015 4 3 11 42 43 Choosing the installation location When installing more than 1 outdoor unit When the air outlet is towards the wall ou un y U U 1500 or more Unit mm When 3 sides of the outdoor unit are blocked by the wall 300 or more D D U D j ale gt 300 or more 600 ormore 6000rmore 600 or more When the walls are blocking front and the rear side of the outdoor units Lo U I y BE U 600 or more gt m 600 or more 300 or more 1500 or more When front and rear side of the outdoor unit is towards the wall Ue el el k Ll J k Le 1500 or more 600 or more 3000 or more 3000 or more 200 or more When the upper part of the outdoor unit and the air outlet is opposite the wall 300 or more er 500 or more e 500 o
20. compliant units The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper connection of electric and requirements set forth in the Operating limits table included in the manual shall immediately invalidate the warranty The air conditioner should be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry Do not use the units if damaged If problems occur switch the unit off and disconnect it from the power supply In order to help prevent electric shocks fires or injuries always stop the unit disable the protection switch and contact SAMSUNG technical support if the unit produces smoke if the power cable is hot or damaged or if the unit is very noisy Always remember to inspect the unit electric connections refrigerant tubes and protections regularly These operations should be performed by qualified personnel only The unit contains moving parts which should always be kept out of the reach of children Do not attempt to repair move alter or reinstall the unit If performed by unauthorized personnel these operations may cause electric shocks or fires Do not place containers with liquids or other objects on the unit All the materials used for the manufacture and packaging of the air conditioner are recyclable The packing material and exhaust batteries of the remote controller optional must
21. in an unusual location such as in an industrial area or near the seaside where it is exposed to the salt in the air please contact your nearest service center In the event of a service issue please refer to the troubleshooting guide of the relevant supporting technical manuals It is recommended that a skilled service technician be contacted for support Should urgent support be required then using the information provided contact the local Samsung office via email or telephone so that support can be initiated via our approved service centres ASC S within 24hrs English 8 A3050 EE Good IB amp IM_DB68 05270A_EN indd 8 2015 4 3 11 42 32 ZS NE Do not touch the circuit breaker with wet hands P This may result in electric shock Do not turn the air conditioner off with the circuit breaker while it is operating gt Turning the air conditioner off and then on again with the circuit breaker may cause a spark and result in electric shock or fire After unpacking the air conditioner keep all packaging materials well out of the reach of children as packaging materials can be dangerous to children gt Ifa child places a bag over its head it may result in suffocation NOILYHVd34d LO Do not touch the air flow blade with your hands or fingers during the heating operation This may result in electric shock or burns Do not insert your fingers or foreign substances into the air inlet outlet of the air condi
22. miens lard nee ner 6 Checking before Use 4 2 5ssssssssssnsss essence tanins a En nent entame BER quien eiserne 12 Basic function Checking theiname Ohthe parts sinne re ee 13 Checking theremote controller u een T EEE E EEEE 14 Basie functors saesson nsan E rnani arena este date tete tentant nets 16 Adjusting theair low directions essen nn einen 18 Timer Setting the Curent times seele a GRENE Ea EE 19 Setting the On Of TIME ENS ere EA ae een 20 good sleep mode urn ern dee AE ET EEEE R EERE 22 Options 2 Step cooling function een denn nanas EEES 23 Using the Fast functiOnss 55s1sscesuaea esa sagatacesagecncts E E AANA akedescstuuanwen saausdaateaeayacests 24 Using the Comfort function a2 ve es santa nt Seen serrate rene arte ane ee 24 Using the Single User function nassen tens na men nee aa 25 Using the Quiet functio sss snenia hasse Le annee aan een 26 Settings Using the Auto clean PUNCO ss ae ee eher 27 Checking the power consumpti a sten nn ee en ee 27 Setting the Beep SONO ee ee ee he ee E EE E 28 ResettingtheFiltercl an reminder sms nern een 28 Setting the Display option scene e ASEE didnnr ne esse teen nes 28 Using the Smant A CappliCatiONs arena secs caen ete amenant dede ont 29 Others Cleaning the aif CONdItIONEl lt 5 inintade Sree cous see dae e ie E ne nete a a ipii ee done 30 Maintaining the air conditiher ssssssmss rsssssereoneseneacdodduiteitseteseeieenmneeneentennentedeniestiaintee 33 THOUDIESHOOLING E
23. requires two 1 5V AAA 2 Insert two AAA batteries type batteries Check and match the and signs accordingly Make sure Storing the remote controller you have inserted the batteries in correct position When you do not use the remote controller for long time 3 Close the cover by place it back to its original position remove the batteries from the remote controller and store it You should hear click sound whey the cover is locked properly The signal may not be received well of electronic lighting style fluorescent lamps such as inverter fluorescent lamps are in the same space Ifother electrical products operate by the remote controller call your nearest contact center Correct disposal of batteries in this product Applicable in countries with separate collection systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system English 15 NOILDNNA DISV4 ZO
24. the drain _ hose pour water into 0 0 7 the drain pan to check 5cm whether the hose is well Hess E Ditch drained Keep a clearance ofat least Do not place the end of the 5cm between the end ofthe drain hose ina hollow drain hose and the ground 1 Correct connection 2 Incorrect connection Drain hose Pipe Don ttie drain hose to the assembly pipe which may lead to water leakage Ifthe diameter of the connection hose is smaller than the product s drain hose water leakage may occur I Drain hose installation 1 If necessary connect the 2 meter extension drain hose to the drain hose 2 Ifyou use the extension drain hose insulate the inside of the extension drain hose with a shield 3 Fit the drain hose into 1 of 2 drain hose holes then fix the end of the drain hose tightly with a clamp Ifyou do not use the other drain hose hole NOTE block it with a rubber stopper 4 When extending the Drain Hose hold the end of Drain Hose and Extended Hose rotate and insert the drain hose into Extended hose for 40 45 mm Make sure the two hoses are firmly connected there is no water leakage Drain hose hole 5 Connect the Drain Hose after using Foam Insulation to wrap the Extended Hose Then Use vinyl tape to wrap the each side of connection by 20 mm English 51 A3050 EE Good IB amp IM_DB68
25. to damage the product nor injure yourself during this process Check if the air conditioner is operating in defrost mode When the ice formed in winter or the outdoor temperature is too low the air conditioner operates in defrost mode automatically In defrost mode indoor fan stops and warm air does not come out Ifthe doors or windows are open it may cause bad cooling heating performance Close the doors and windows Check if the air conditioner has just been turned on after stopping cooling or heating operation In this case just a fan will run to protect the outdoor unit compressor Check if the pipe length is too long When the pipe length exceeds maximum allowable pipe length cooling heating performance may decrease English 34 2015 4 3 11 42 42 BR A3050 EE Good IB amp IM_DB68 05270A_EN indd 35 PROBLEM SOLUTION Air flow adjustment Check if you have selected good sleep mode In cool mode you is not working cannot adjust the air flow direction If the good sleep mode is operating in Heat mode you can adjust the air flow direction Fan speed Check if you have selected Auto Dry Fast Comfort adjustment is not working good sleep mode In these mode fan speed is set to Auto and you cannot adjust the fan speed Remote controller is Check if your batteries are depleted not working Make sure nothing is blocking your remote controller sensor C
26. 1 Determine the positions of the wooden uprights to be 1 Use stud finder to find out locations of the studs attached to the window frame 2 Attach the wooden uprights to the window frame giving attention to the weight of the indoor unit 3 Attach the installation plate to the wooden upright using tapping screws 2 Fix the plate hanger on two studs English 42 A3050 EE Good IB amp IM_DB68 05270A_EN indd 42 2015 4 3 11 42 45 Search for other spots if there are less than two studs or the distance between the studs are different from the plate hanger CAUTION Fixthe installation plate without inclining to one side Make sure that a wall can withstand the weight of the product If you install the product in a place where it is warning NOt strong enough to withstand the product weight the unit could fall and cause injury Assembling the hanger screw Use 2 screws to fix the indoor unit with hanger plate as shown in the picture NOILVTIVISNI ZO Please scan this QR code for detail video of indoor unit installation In order to install the indoor unit you must disassemble the cover panel first Please proceed following instructions to disassemble and assemble the cover panel Hooks on the cover panel may get damaged if you apply excessive force as you disassemble and assemble the cover panel Please follow the following instructions Removing the screws Cover panel is assembled
27. 18 A3050 EE Good IB amp IM_DB68 05270A_EN indd 18 2015 4 3 11 42 34 MEME a oo Setting the Current time Before using the functions of the air conditioner set the current time 1 Press the Settings button 2 Press the Q or Settings button until Colck indicator starts to blink 3 Press the SET button to set the Colck function Colck indicator will be displayed on the remote controller display and you can set the time 4 Press the button to set the time You can set the time in hourly units from 1 hour 12 hours according to AM PM and in minute units from 0 59 minutes YAWIL 0 5 Press the SET button to complete the current time setting Current time setting will be cancelled if you don t press the SET button within 10 seconds after setting the time Therefore check for the current time on the remote controller display Remote controller display English 19 A3050 EE Good IB amp IM_DB68 05270A_EN indd 19 2015 4 13 14 24 48 Check the current time on the remote controller before using this function caution The default time is 1 AM on the remote controller The current time is reset to default time after changing the batteries You can set the air conditioner to turn on off automatically at desired time Setting On timer while the air conditioner is off Off timer while the air conditioner is on 1 Press the Timer button to select On Off On Off indicator will
28. 2015 4 3 11 42 42 MMM CON NE Choosing the installation location Outdoor Unit Where it is not exposed to strong wind Well ventilated and dustless places Where possible keep out of sunlight and rain Where neighbors are not annoyed by operation sound or hot air Solid wall or support that prevents vibration and is strong enough to hold the product weight Where there is no risk of flammable gas leakage When installing the unit at a high place be sure to fix the unit legs 3 m or more away from the TV or radio to prevent the screen from being distorted or noise from being generated Install the unit horizontally Place where drained water does not become any problem Place with no plants especially climbing plants and where small animal can not access Outdoor unit should not be place higher than 2 4 m or directly under eaves for accessibility for service and OH amp S reasons vvvvvvvvvvvy Avoid the following places to prevent malfunction of the unit Where there is machine oil Salty environment such as seaside areas CAUTION Where sulfide gas exists Other special atmosphere areas Outdoor 100 mm or more Unit recommended 125 mm or mor Se mone 125 mm or more Outer wall recommended pi LL 1 recommended Indoor an he Unit a You can select the direction of draining left or right the absorbent pad and raining right vinyl tape Refer to
29. 50 EE Good IB amp IM_DB68 05270A_EN indd 33 2015 4 3 11 42 42 _ mE A3050 EE Good IB amp IM_DB68 05270A_EN indd 34 Troubleshooting Refer to the following chart if the air conditioner operates abnormally This may save time and unnecessary expenses PROBLEM SOLUTION The air conditioner e Check power status and then operate the air conditioner again does notworkatall Plug in or switch on the circuit breaker and then operate the air conditioner again e Ensure Isolator is switch on Check if you have set the Off Timer Operate the air conditioner again by pressing the Power button The temperature Check if you have selected Fan Fast mode In these modes adjustment is not set temperature is set to auto and you cannot adjust the working temperature Cool Warm air does Check if the set temperature is higher during Cool mode not come out the lower during Heat mode than the current temperature Press air conditioner or performance is reduced the Temp or button on the remote controller to change the set temperature Check if the Air filter is blocked by dirt If there is a lot of dust on the Air filter cooling heating performance may decrease Clean them frequently Check if the outdoor unit is covered or installed near the obstacle Take the cover off and take the obstacle away When clearing the obstacle e g snow or ice use suitable tools so as to be careful not
30. A is a mixed type of refrigerant It is necessary for recharging under conditions of liquid When recharging refrigerant from the refrigerant cylinder to the equipment follow the instructions below 1 Before recharging check whether the cylinder has a siphon or not There are two ways to recharge the refrigerant Cylinder with siphon Cylinder without siphon Siphon Charge the refrigerant standing the gt Charge the refrigerant turning the cylinder cylinder upright upside down IfR 410A refrigerant is charged with gas the composition of the charged refrigerant changes and the note Characteristics of the equipment vary During the measuring operation of refrigerant quantity added use electronic scales If cylinder doesn t have syphon upset it R 410A 2088 S GWP Global Warming Potential gt zZ Indoor unit E d a Outdoor unit kg b English 55 A3050 EE Good IB amp IM_DB68 05270A 01_EN indd 55 co 2015 6 5 16 30 39 Performing the gas leak tests Make sure to check for gas leaks before completing the installation process connecting the assembly pipe and hose between indoor unit and outdoor unit insulating the cables hose and pipe and fixing the indoor unit to the installation plate Test part for outdoor unit Test part for indoor unit
31. I m T Temperature indicator i J Filter Clean reminder indicator C F a Defrost indicator F Power consumption indicator Q D D Auto clean indicator Power button Remote controller receiver Wi Fi indicator Timer Auto clean indicator English 13 A3050 EE Good IB amp IM_DB68 05270A_EN indd 13 2015 4 3 11 42 32 ZS CON NE Checking the remote controller Point the remote controller towards the remote controller receiver of the indoor unit When you properly press the button on the remote controller you will hear beep sound from the indoor unit and a transmit indicator appears on the remote controller display I Remote controller buttons Before using the functions of the remote controller you should set the current time Refer to page 19 Vertical air swing Activate Deactivate vertical air flow blade movement automatically Mode amp Set one of the 5 operating modes D Power Turn on off the air conditioner Fana v Adjust the fan speed Temp Increase Decrease the temperature by 1 C Single User Turn on off the Single User function which reduces energy usage while operating in cool mode Options Select options during operation Timer Select Timer option Settings Select settings SET Set Cancel the selected option or Directional lt gt setting Move through th
32. If they are not supplied you should obtain them before installing the air conditioner Insulated Assembly Insulated Assembly PET3 Foam Tube a A Pipe 6 35 mm 1 Pipe 9 52 mm 1 Insulation 1 Vinyl Tapes 2 Drain Plug 1 Q Q Be i M4x25 Tapped Rubber Legs 4 Pipe Clamps A 3 Pipe Clamps B 3 Cement Nails 6 Screws 6 Drain Hose length 2m 1 Putty 100 g 1 Foam Insulation 1 B If these accessories are supplied they will be in the accessory box NOTE Tools required for installation General Tools Vacuum Pump Backward flowing prevention Manifold Gauge Torque Wrench Pipe Cutter e Reamer Pipe Bender Screw Driver Spanner Drill LWrench Tools for test operations Thermometer Resistance Meter Electroscope A3050 EE Good IB amp IM_DB68 05270A_EN indd 41 English 41 Stud Finder Spirit Level Measuring Tape 2015 4 3 11 42 44 Fixing the installation plate You can select the direction of the drain hose depending on where you want to install the indoor unit Therefore before fixing the installation plate to a wall or a window frame you must determine the position of the 65mm hole through which the cable pipe and hose pass to connect the indoor unit to the outdoor unit When facing the wall the pipe and cable can be connected from the Right A Direction of pipe Left B SE
33. L OR VISIT US ONLINE AT UK 0330 SAMSUNG 7267864 www samsung com uk support EIRE 0818 717100 www samsung com ie support 0180 6 SAMSUNG bzw 0180 6 7267864 0 20 Anruf aus dem dt Festnetz aus dem Mobilfunk max 0 60 Anruf GERMANY HHP 0180 6 M SAMSUNG bzw www samsung com de support 0180 6 67267864 0 20 Anruf aus dem dt Festnetz aus dem Mobilfunk max 0 60 Anruf FRANCE 01 48 63 00 00 www samsung com fr support 800 SAMSUNG 800 7267864 i ITALIA HHP 800 Msamsung 800 67267864 www samsung com it support 0034902172678 SPAIN HHP 0034902167267 www samsung com es support PORTUGAL 808 20 7267 www samsung com pt support LUXEMBURG 261 03 710 www samsung com support NETHERLANDS 0900 SAMSUNG 0900 7267864 0 10 Min www samsung com nl support 301 www samsung com be support Dutch BELGIUM 02 201 24 18 www samsung com be_fr support French NORWAY 815 56480 www samsung com no support DENMARK 70701970 www samsung com dk support FINLAND 030 6227 515 www samsung com fi support SWEDEN 0771 726 7864 0771 SAMSUNG www samsung com se support D 801 172 678 lub 48 22 607 93 33 POLAND HHP 801 672 678 lub 48 22 607 93 33 www samsung com pl support koszt polaczenia wedtug taryfy operatora 0680SAMSUNG 0680 726 786 HUNGARY 0680PREMIUM 0680 773 648 www samsung com hu support SLOVAKIA eg www samsung com sk support 0800 SAMSUNG 0800 7267864 AUSTRIA Only for Premium HA 0800 366661 www samsung com
34. OTE place Pump down procedure when removing the product 1 Press the Power l button on the indoor unit for 5 seconds Beep will sound immediately to let you know that the product is ready for pump down procedure Please let the compressor run for more than 5 minutes Release the valve caps on High and Low pressure side Use L wrench to close the valve on the high pressure side After approximately 2 minutes close the valve on the low pressure side Stop operation of the air conditioner by pressing the power button on the indoor unit or remote controller au A UUN Disconnect the pipes English 60 2015 4 3 11 42 53 How to connect your extended power cables Items to prepare compressor and insulation tape should be prepared by an installation technician Tools Crimping pliers Connection sleeve mm Insulation tape Contraction tube mm Spec MH 14 20x 7 0 HxOD Width 18 mm 50x 8 0 LxOD Shape C SS o 1 As shown in the figure peel off the shields from the rubber wire of the power cable Peel off 20 mm of the wire shields of the tube installed already N After peeling off the tube wire you must insert a contraction tube CAUTION Insert both sides of core wire of the power cable into the connection sleeve Using a compressor compress the two points and flip it over and compress another two points in the same location The compression dimension shoul
35. T EE ER ER nee rem Eee 34 Installation Salety Precautions lt 252ss ccvesesssunniaaaceaneses er Er a aganaaconsmendsnatovacteantuorsdausdeadearoheatansnennanas 36 Choosing the installation location siinses rren ves cacteasonganadeshennadeagaeanaseaisund ARASEN EONTR SS 37 ACCOSSOMNES nn seen nn O pese sme esas ee net nee een Anne nds Ce tiens st Fixing the installation plate Disassembling Assembling the Cover panel for indoor unit installation 43 Conn cting th assembly cable se seen ee 45 Installing and connecting the assembly pipe of the indoor unit 47 Evac atingitheindoor nit snn eeen ea re ne enter rates ete eee Cutting or extending the pipe Installing and connecting the drain hose of the indoor unit 51 Changing direction ofthe drain hos a near tetes 52 Installing and connecting the drain hose of the outdoor unit 53 Evacuatingithe connected Pipess nn use na keinen 53 Performing the gas leaktests Sn anna E OE ansteuern 56 Exingitheiindoorunitinplace acer en Tee Eee 57 Fixing the outdoor uinitiin Place un ee en tenta side ne 57 Smartinstalllm des n s2 near en ern Final check and trial operation Pump down procedure when removing the product 60 How to connect yourextendedipowencables u nn ren ee 61 Display Error and Check Method een nee ee 62 English 3 A3050 EE Good IB amp IM_DB68 05270A_EN indd 3 2015 4 3 11 42 31 Product Specificat
36. a year P Failing to do so may result in injury death or property damage Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Do not stand on top of the appliance or place objects such as laundry lighted candles lighted cigarettes dishes chemicals metal objects etc on the appliance This may result in electric shock fire problems with the product or injury Do not operate the appliance with wet hands This may result in electric shock Do not spray volatile material such as insecticide onto the surface of the appliance amp D As well as being harmful to humans it may also result in electric shock fire or problems with the product Do not drink the water from the air conditioner gt The water may be harmful to humans Do not apply a strong impact to the remote controller and do not disassemble the remote controller Do not touch the pipes connected with the product This may result in burns or injury Do not use this air conditioner to preserve precision equipment food animals plants or cosmetics or for any other unusual purposes This may result in property damage Avoid directly exposing humans animals or plants from the air flow from the air conditioner for long periods of time This may result in harm to humans animals or plants English 10 A3050 EE Good IB amp IM_DB68 05270A_EN indd 10 2015 4 3 11 42 32
37. ass the assembly cable through the rear of the indoor unit and connect the assembly cable to terminals Refer to the picture below B Each wire is labeled with the corresponding terminal number NOTE Pass the other end of the cable through the 65 mm hole in the wall Close the connector cover by tightening the screw carefully Close the cover panel Remove the terminal board cover on the side of the outdoor unit Connect the cables to the terminals as seen in the picture onan B Each wire is labeled with the corresponding terminal number NOTE Indoor unit OJAN F1 F2 Indoor unit Ground wire 2 Green Yellow I Ground wire Green Yellow Es 818 Outdoor unit B 88 I Outdoor unit Also circular terminal must be matched with screw size in terminal block After connecting the cables make sure terminal numbers on the indoor outdoor unit matches Please ensure that Power amp Communication cables are separated they must not be in the same cable CAUTION 10 Connect the grounding conductor to the grounding terminals 11 Close the terminal board cover by tightening the screw carefully In Russia and Europe consult with the supply authority to determine the supply system impedance before
38. ate vacuum according to page 53 55 After opening valves check leaks using a leak detector for refrigerant Pump down before disconnecting the refrigerant connections for unit repair removal or disposal Pump down is an operation intended to collect all the system refrigerant in the outdoor unit This operation must be carried out before disconnecting the refrigerant tubing in order to avoid refrigerant loss to the atmosphere gt Shut off the liquid valve with the Allen wrench gt Turn the system on in cooling with fan operating at high velocity Compressor will immediately start provided 3 minutes have elapsed since the last stop gt After 2 minutes of operation shut the suction valve with the same wrench gt Turn the system off and switch mains supply off gt Disconnect tubing After disconnection protect valves and tubing ends from dust gt Compressor damage may occur if run at a negative suction pressure English 56 A3050 EE Good IB amp IM_DB68 05270A_EN indd 56 2015 4 3 11 42 51 Fixing the indoor unit in place Perform the following work on the area where gas leak test was done priory After checking for gas leaks in the system insulate the pipe hose and cables Insulation Then place the indoor unit on the installation plate 1 To minimise condensation problems wrap foam insulation as shown in the o figure on a part without insulation on the end of the pipes 2 Wind the pipe assembly cable an
39. be disposed of in accordance with current laws The air conditioner contains a refrigerant that has to be disposed of as special waste At the end of its life cycle the air conditioner must be disposed of in authorized centers or returned to the retailer so that it can be disposed of correctly and safely Installing the unit IMPORTANT When installing the unit always remember to connect first the refrigerant tubes then the electrical lines gt Always disassemble the electric lines before the refrigerant tubes Upon receipt inspect the product to verify that it has not been damaged during transport If the product appears damaged DO NOT INSTALL it and immediately report the damage to the carrier or retailer if the installer or the authorized technician has collected the material from the retailer English 36 A3050 EE Good IB amp IM_DB68 05270A_EN indd 36 2015 4 3 11 42 42 gt After completing the installation always carry out a functional test and provide the instructions on how to operate the air conditioner to the user gt Donotuse the air conditioner in environments with hazardous substances or close to equipment that release free flames to avoid the occurrence of fires explosions or injuries So uw gt To prevent injury when accidentally touching the indoor unit fan its recommended to install the indoor unit as high as possible CA a eee ee BR gt gt The air conditioner should be used onl
40. d 25 2015 4 3 11 42 38 ZS CON EU Using the Quiet function You can reduce the noise generated from an indoor unit during Cool Heat mode When the air conditioner is operating in Cool Heat mode 1 Press the Options button 2 Press the X C or Options button until Quiet indicator starts to blink 3 Press the SET button to set the Quiet function Quiet Quiet indicator will be displayed on the remote controller display and Quiet function will begin gt Press the Options button gt Press the gt or Options button to Cancel make the Quiet indicator blink and press the SET button Additional options available in Quiet function ar You can adjust the set temperature by 1 C within the range of Tempi 16 C 30 C in Cool mode and 8 C 30 C in Heat mode 7N Fam Fan speed is set to lt Auto Vv Remote controller display Vertical air swing can be selected Quiet function is only available in Cool Heat mode NOTE If the Quiet function is selected while 2 Step Cooling Fast Comfort Single user good sleep function is on corresponding function will be cancelled English 26 A3050 EE Good IB amp IM_DB68 05270A_EN indd 26 2015 4 3 11 42 39 MEME CON EU Using the Auto clean function Auto clean function will minimise the moisture inside of the indoor unit Activate this function to help provide you with clean air When th
41. d be 8 0 After compressing it pull both sides of the wire to make sure it is firmly pressed Wrap it with the insulation tape twice and position your contraction tube in the middle of the insulation tape Apply heat to the contraction tube to contract it After tube contraction work is completed wrap it with the insulation tape to finish Unit mm Power cable provided by us NOILVTIVISNI ZO Comp dim amp AT it 4 times 5 mm Insulation tape 40 mm Contraction tube B tape In case of extending the electric wire please DO NOT use a round shaped pressing socket warning ncomplete wire connections can cause electric shock or a fire English 61 A3050 EE Good IB amp IM_DB68 05270A_EN indd 61 AR 2015 4 3 11 42 54 _ a le Display Error and Check Method Indoor Display Error and Check Method ERROR MODE Outdoor DESCRIPTION YEL GRN RED Indoor Normal operation Power on reset 1sec Power off VDD NG When dF shows on the 88 segment of the Indoor unit this means that the system is in defrost mode Note that during this operation period system performance will be reduced Communcation error Indoor Outdoor Indoor room temperature sensor error Evap In temperature sensor error Fan error Indoor EEPROM error Indoor Option setting error 1min Time out Communcation Inv micom Main micom
42. d drain hose with vinyl tape Pipes 3 Place the bundle the pipe assembly cable and drain hose in the lower part of the indoor unit carefully so it does not project from the rear of the indoor unit Installation plate 4 Hook the indoor unit to the installation plate and move the unit to the right Vinyl tape and left until it is securely in place Se Connecting wires Make sure pipe does not move when you install the indoor unit on Drain hose curon an installation plate 5 Wrap the rest of the pipe with vinyl tape 6 Attach the pipe to the wall using clamps optional Fixing the outdoor unit in place Install the outdoor unit in level on a stable base to help avoid the generation of noise and vibration especially when installing the unit close to a neighbor 612 mm If you install the outdoor unit in a place exposed to strong winds or at a height fix it to an ra a appropriate support wall or ground 317 1 Place the outdoor unit as indicated on the top of the unit to let the discharged air out S Rubberle properly a 2 Fix the outdoor unit in level to an appropriate support using anchor bolts 3 Ifthe outdoor unit is exposed to strong winds install shield plates around the outdoor unit so that the fan can operate correctly Secure the rubber leg to help prevent the generation of noise and vibration NOTE Outdoor unit installed on the wall by rack Ensure t
43. ditioner will heat your room You can adjust the temperature to feel warmer during the cold season Fan may not operate for about 3 5 minutes at the beginning to prevent any cold blasts while the air conditioner is warming up Quiet mode makes the noise quieter during the operation of the indoor unit in the Heat mode Since the air conditioner heats the room by taking heat energy from outdoor air the heating capacity may decrease when outdoor temperature is extremely low Use an additional heating appliance in combination with the air conditioner if you feel the air conditioner heats insufficiently English 16 A3050 EE Good IB amp IM_DB68 05270A_EN indd 16 2015 4 3 11 42 33 Press the button to turn on the air conditioner Press the button to setthe operating mode o N Each time you press the Mode button the mode will change in order of Auto Cool Dry Fan and Heat g in Auto Cool Dry A Fan Heat 1 SL Zur s SL Di ct Li 5 3 JA y MAM zZ Press the button to adjust the temperature Auto You can adjust the set temperature by 1 C within the range of 16 C 30 C Cool You can adjust the set temperature by 1 C within the range of 16 C 30 C Dry You can adjust the set temperature by 1 C within the range of 18 C 30 C Fan Temperature adjustment is not possible Heat You can adjust the set temperature by 1 C wit
44. e center and bottom hooks in this sequence Tighten the bottom panel with the screws and close the screw holes with their cap lt Fasten the screw gt lt Assemble the Cap screw gt English 44 A3050 EE Good IB amp IM_DB68 05270A_EN indd 44 amp 2015 4 3 11 42 48 EEEE o a NE Connecting the assembly cable I Cable specification Model Power cable Interconnection cable Type GL 3G1 0mm HO7RN F ARIOHSESPWIVEE 3G1Smm HO7RN ve 2x0 75mm HOSRN F e Connect the power cable to the auxiliary circuit breaker If every pole fails to connect to the power supply it must be incorporated in a wire with a contact opening of 23 mm Use shield cable Category 5 less than 50pF m for noisy environmental site NOILVTIVISNI ZO NOTE Power supply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed flexible cord Code designation IEC 60245 IEC 66 CENELEC HO7RN F IEC 60245 IEC 57 CENELEC HOSRN F I Connecting the cable Electrical work 1 For electrical and earth works comply with the technical standards of electrical installations and the the wiring regulations of the Local wiring regulations 2 Tighten the terminal block screw to 1 2 1 8 Nem 12 18 kgf cm 3 Precautions when connecting terminal blocks of the indoor unit gt Before connecting make sure the connecting part of the terminal socket is facing upwards f
45. e Timer Options or Settings menu to make a selection In case you wish to cancel the options or settings that you have just set press the Options or Settings button again NOTE then the most recently selected item will blink and you may simply cancel it by pressing the SET button while selected item is blinking English 14 A3050 EE Good IB amp IM_DB68 05270A_EN indd 14 2015 4 3 11 42 32 I Remote controller display A peas Transmit indicator Operation mode indicator Low battery indicator Set temperature Time for Timer option indicator aes Off Fan speed indicator indi ii Ex 1AM good sleep indicator Le ut oc PMhi Vertical air swing indicator Options indicator Settings indicator Make sure that the water does not get to the remote controller The following functions are displayed on the remote controller display but not supported in this model SPi Can d light Cool When turning off and turning on the remote controller the Timer Options and Settings set before turning off the remote controller are cancelled However the fan direction does not change CAUTION Low Battery warning Inserting the batteries When the battery is exhausted 54 will be displayed in the 1 Push the lever as arrow indicates on the rear side of the remote controller display When the icon appears change remote controller and pull up the batteries The remote controller
46. e air conditioner is operating 1 Press the Settings button 5 2 Press the or Settings button until Clean indicator starts to blink m 3 Press the SET button to setthe Auto clean function d 3 seconds after setting Auto clean function Clean indicator on the remote a controller display will disappear and Auto clean and Timer indicator will turn on the indoor unit display Auto clean function will be activated after the air conditioner stops operating Duration ofthe Auto clean function can be different depending on the previous operation mode used Auto cool Cool Dry mode 30 minutes Auto heat Heat Fan mode 15 minutes nel gt Press the Settings button gt Press the Q or Settings button to make the Clean indicator blink and press the SET button Indoor unit display When the operation mode is set during Auto clean function is activated the air conditioner will operate in chosen operation mode and the Auto clean function will be re activated when the operation stops During the auto clean function indoor fan will continue to run and air D flow blade will remain open to expel ambient air amp Checking the power consumption This function will display the amount of electricity consumed by operating the air conditioner When the air conditioner is operating 1 Press the Settings button 2 Press the Q or Settings button until Usage indicator starts to blink 3 Press the SET b
47. ed properly Easy Installation It s so easy to install You can easily hang the product on the wall and connect the pipes and wires by opening the cover on the bottom of the product Now you won t have to tilt the product to connect the pipe and the wires x Correct Disposal of This Product Aue Waste Electrical amp Electronic Equipment Applicable in countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal English 2 A3050 EE Good IB amp IM_DB68 05270A_EN indd 2 2015 4 3 11 42 31 Contents Preparation Safety precautions oirassa nan Gr nt nee
48. er Reset indicator starts to blink 3 Press the SET button to reset Filter clean reminder 3 seconds after setting Filter clean reminder function Filter Reset indicator on the remote controller display will disappear and CF indicator on the indoor unit display will disappear Indoor unit display Setting the Display option Display lighting can be adjusted by following this instruction 1 Press the Settings button 2 Press the Q or Settings button until Display indicator starts to blink 3 Press the SET button to set the display status 3 seconds after setting Display function Display indicator on the remote controller display will disappear and indoor unit display will be turned off gt Press the Settings button gt Press the or Settings button to make Display indicator blink and press the SET button gt Display indicator on the remote controller display will disappear and the indoor unit display will be turned on again Cancel English 28 A3050 EE Good IB amp IM_DB68 05270A_EN indd 28 2015 4 3 11 42 41 ZS CON NE Using the Smart A C application You can conveniently control your air conditioner anywhere with Smart APP WIFI WPS is not seen to new remote control LCD It is hidden function 1 Press the Timer button to set the WiFi function Press the Timer button for 4 seconds T will blink first then FE appears on the remote controller display fo
49. f the drain pan 4 Attach the rubber cap with a screwdriver by turning it to the left until it fixes to the end of the groove 5 Check for leakage on both side of the drain outlet NA Pour the water in direction of arrow Direction of the drained water ga Le Make sure the indoor unit is in upright position when you pour water to check for leakage Make sure that the water does not overflow onto the electrical part CAUTION English 52 A3050 EE Good IB amp IM_DB68 05270A_EN indd 52 2015 4 3 11 42 50 Installing and connecting the drain hose of the outdoor unit While heating ice may accumulate During the process of defrosting check if condensation draining is adequate For adequate draining do the following 1 Insert the drain plug into the drain hole on the underside of the outdoor unit To avoid drain plug from contacting the ground secure gap between the Ganon ground and the bottom surface of the outdoor unit Drain hole een plug NOILVTIVISNI ZO Bottom surface of outdoor unit 2 Connect a drain hose to the drain plug Drain hole Drain plug Drain hose 3 Ensure that condensation draining is adequate AN Snow proof hood To avoid this incident install a frame that is higher than estimated snow fall In addition install a snow proof hood to avoid snow from piling on the Estimated outdoor un
50. fore using the air conditioner again dry the inner components of the air z conditioner again by running in Fan mode for 3 to 4 hours This helps remove odors which may have generated from dampness I Periodical checks Refer to the following chart to maintain the air conditioner properly Type Description ae is ti Once a year Clean the air filter 1 Q Clean the condensate drain pan 2 Indoor Thoroughly clean the heat exchanger 2 e unit Clean the cross fan 2 J Clean the condensate drain pipe 2 Replace the remote controller batteries 1 gt Clean the heat exchanger on the outside ofthe unit 2 Clean the heat exchanger on the inside ofthe unit 2 Clean the electric components with jets of air 2 Outdoor Verify that all the electric components are firmly unit tightened 2 Clean the fan 2 Verify that all the fan assembly is firmly tightened 2 Clean the condensate drain pan 2 o Periodical checks marked with a square should be performed more frequently if the area of installation is very dusty Periodical checks marked with a circle should be performed in line with guidance CAUTION Periodical checks marked with a spot should be performed by qualified personnel NOTE In accordance with local guidelines for the products listed within this manual spare parts will be made available for 10 years after the official manufacturers End of Life EOL date English 33 A30
51. gt Sound sleep gt Wake up stage When the air conditioner is operating in Cool Heat mode 1 Press the Timer button to select Co indicator will keep blinking and you can set the time 2 Press the button to set the time You can set the time in half hour unit from 30 minutes 0 5 on the display 3 hours and hour unit from 3 12 hours Time can be set from minimum 30 minutes to maximum 12 hours Default time setting for the good sleep mode is 8 hours 3 Press the SET button to complete the good sleep mode setting Cool indicator and the set time of the good sleep mode will be displayed on Em the remote controller display EE En c Timer indicator will be displayed on the indoor unit display on l gt Lt good sleep mode setting will be cancelled if you don t press the SET button within yon Di 10 seconds after setting the time Therefore check for the amp indicator on the remote controller display and the Timer indicator on the indoor unit display gt Press the Timer button gt select 2 gt press the Jor C button gt Cancel set the timer to press the SET button Remote controller display Additional options available in good sleep mode You can adjust the set temperature by 1 C within the range of 16 C 30 C Cool 8 C 30 C Heat s When the good sleep mode is on In Cool mode Air flow direction will be adjusted automa
52. he installation site Tightness of pipe connection to detect gas leak Electric wiring connection Heat resistant insulation of the pipe Drainage Grounding conductor connection Correct operation follow the steps below 1 Press the Power button and check the following gt The indicator on the indoor unit lights up gt The airflow blade opens and the fan gears up for operation 2 Press the Mode button to select Cool or Heat mode gt In Cool mode use Temp or button and set the temperature at 16 C gt In Heat mode use Temp or button and set the temperature at 30 C Approximately 3 5 minutes later outdoor unit will start to operate and the Cool or Warm air will blow out After 12 minutes of stationary condition check the indoor unit air treatment NOTE Cooling mode indoor unit check gt Inlet air temp Outlet air temp From 10 C to 12 C indicative delta T Heating mode indoor unit check Outlet air temp Inlet air temp From 11 C to 14 C indicative delta T In heating mode the indoor fan motor can remain off to avoid cold air blown into conditioned space 3 Press the Air swing button and check the following gt The airflow blades work properly 4 Press the Power button to stop the operation When you complete the installation successfully hand over this manual to the user for storage in a handy and safe N
53. he wall will be able to suspend the weight ofrack and outdoor unit Install the rack close to the column as much as possible Install proper grommet in order to help reduce noise and residual vibration transferred by outdoor unit towards wall Designed to cut off residual vibration from outdoor unit to rack not supplied with product Y Soft rubber designed to cut off vibration from rack to wall not supplied with product English 57 NOILVTIVISNI ZO A3050 EE Good IB amp IM_DB68 05270A_EN indd 57 2015 4 3 11 42 51 Smart Install mode This model supports Smart Install mode which checks installation status to find out ifthere is any problems with any ofthe functions Execute Smart Install mode after installation 1 Check the installation status of the air conditioner 1 Check the power supply service valve if it s open power cable of the indoor and outdoor unit and amount of additional refrigerant required for pipe extension 2 Status of the indicator after supplying the power Standby status 2 When the air conditioner is in standby status use the remote controller to start the Smart Install mode 1 Press the Set Mode and Power ch button simultaneously for 4 seconds Remote controller may be different image functions depending on the model English 58 A3050 EE Good IB amp IM_DB68 05270A_EN indd 58 2015 4 3 11 42 52 2 Smart Install mode in
54. heck that there are strong lighting apparatus near the air conditioner Strong light which comes from fluorescent bulbs or neon signs may interrupt the electric waves Timer function does Check if you press the SET button on the remote controller not set after you have set the time The indicator Press the Power button or disconnect the power plug is blinking switch off the auxiliary power switch continuously If the indicator is still blinking contact the service center Odors permeatein Check if the appliance is running in a smoky area Ventilate the the room during room or operate the air conditioner in Fan mode for 1 2 hours operation We do not use smelly components in the air conditioner Check the Drains have been cleared Regular Maintenance Error is indicated When an indoor unit indicator blinks contact the nearest service center Please ensure the error code is passed onto the service center when booking the service call Noise is generated Depending on the status of the air conditioner usage noise can be heard when refrigerant flow movement changes It is normal Excessive Noise is If excessive irregular noise is generated in conjunction with Generated reduced product performance please refer to your service and Reduced engineer to ensure the product is operating correctly Performance Smoke is generated If may not be a fire but it can be a steam generated by the
55. hin the range of 8 C 30 C Press the button to set the desired fan speed Lu En Auto Cool de T uns Dry F Auto Flow F Meo High Turbo ee 2 Auto Low ZE Med High Turbo B Dry mode is only available in the cooling mode NOTE English 17 A3050 EE Good IB amp IM_DB68 05270A_EN indd 17 2015 4 3 11 42 34 Adjusting the air flow direction This function will allow you to adjust the air flow direction vertically Pressthe button to make air flow blades vertically Vertical air flow gt Tokeep the air flow direction in a constant direction press the button again The air flow blade s will stop the movement gt Ifyou adjust the vertical air flow blade manually it may not close completely when you turn off the air conditioner Adjusting the air flow direction is not available in Note Jood sleep mode while it is in cool mode However you can adjust the air flow direction in good sleep mode while it is in heat mode Remote controller display I Horizontal air flow position you prefer Move the blade pin lever left or right to keep the air flow direction in a constant To avoid the risk of personal injuries adjusting the horizontal air flow aution direction should only be done when the unit is turned off completely There is a potential risk of personal injury when the unit is mishandled English
56. ions Cooling capacity Min Nom Max ARO9HSFSPWKNEE 0 90 2 50 3 30 AR12HSFSPWKNEE 0 90 3 50 4 00 Heating capacity Min Nom Max 0 80 3 20 6 30 0 80 4 00 7 00 Power input Seasonal efficiency according to EN14825 Cooling Min Nom Max 0 20 0 52 0 75 0 20 0 84 1 11 Heating Min Nom Max Energy grade 0 17 0 64 1 85 0 17 0 95 2 20 Pdesign Cooling SEER Annual energy consumption Energy grade Heating Pdesign Average SCOP climate Annual energy consumption Energy grade Heating Pdesign Colder SCOP climate Annual energy consumption Nominal efficiency according D to EN14511 EER COP Energy grade Cooling Heating Casing Colour White Dimensions Unit WidthxHeightxDepth 896x261x261 Weight Unit 11 0 Fan Air flow rate Cooling High Mid Low 10 0 6 9 3 9 106 75 45 Heating High Mid Low 11 1 8 0 5 0 114 83 53 Sound power Cooling High 56 0 58 0 Sound pressure Cooling High Silence 38 17 40 17 Heating High Silence 38 17 40 17 Piping connections Liquid OD 6 35 Gas OD 9 52 Power supply Phase Frequency Voltage 1 50 220 240 Motor Type Output DC 27 Software version Main Code Version DB91 01550B 150224 Option Seg 1 24 1 7 13 19 are default values
57. it snow fall In areas with heavy snow fall piled snow could block the air intake i Evacuating the connected pipes The outdoor unit is loaded with sufficient R 410A refrigerant Do not vent R 410A into atmosphere it is a fluorinated greenhouse gas covered by Kyoto Protocol with a Global Warming Potential GWP 2088 You should evacuate the air in the indoor unit and in the pipe If air remains in the refrigerant pipes it affects the compressor It may cause reduction of cooling capacity and malfunction Use Vacuum Pump as seen in the picture When installing make sure there is no leakage When recovering the refrigerant ground the compressor first before removing the connection pipe If the refrigerant pipe is not properly connected and the compressor works with the service valve open the pipe inhales the air and it makes the pressure inside of the refrigerant cycle abnormally high It may cause explosion and injury English 53 A3050 EE Good IB amp IM_DB68 05270A_EN indd 53 2015 4 3 11 42 50 Evacuating the connected pipes 1 Connect each assembly pipe to the appropriate valve on the outdoor unit and Outdoor unit Indoor unit tighten the flare nut Gas pipe side 2 Tighten the flare nut first with your hands and then with a torque wrench baba dite applying the following torque OK APE gt 4 B Excessive torque can be cause of gas leakage NOTE O
58. itioner Cleaning the outdoor unit heat exchanger gt When dust accumulates on the heat exchanger it may decrease cooling performance Therefore clean it regularly gt Spray water to clean the dust amp 2 6 ue If itis difficult to clean the outdoor unit heat exchanger on NOTE your own contact service center BR Be careful with the sharp edges on the Heat exchanger CAUTION outdoor unit heat exchanger Illustration may differ slightly depending on the models English 30 A3050 EE Good IB amp IM_DB68 05270A_EN indd 30 2015 4 3 11 42 41 BED E LUE Removing the Air filter Air filter There is a hole on the bottom right side of the filter Put your finger in that hole to get a grip on the filter and slightly push it up to release the hooks from the bottom side Then pull it down to remove the filter from the main body SH1H1O 90 I Cleaning the air filter Washable foam based air filter captures large particles from the air The filter is cleaned with a vacuum or by hand washing Clean the Air filter with a vacuum cleaner or soft brush If dust is too heavy rinse it with running water Remove the Air filter from the main body Insert the Air filter back in its original position Dry the Air filter in a ventilated area Clean the Air fi
59. keep blinking and you can set the time 2 Press the button to set the time You can set the time in hourly units from 1 hour 12 hours according to AM PM and in minute units from 0 59 minutes 3 Press the SET button to complete the On off timer setting On Off indicator and the set time of the timer will be displayed on the remote controller display and the Timer indicator will be displayed on the indoor unit display On Off timer setting will be cancelled if you don t press the SET button within 10 seconds after setting the time Therefore check for the On Off indicator on the remote controller display and the Timer indicator on the indoor unit display Setting On timer gt Press the Timer button gt select On Off gt press the Q or O button Cancel set the timer to press the SET button amp gt Press the Power button When On Off timer setting is completed the set status will be displayed Remote controller display NOTE for 3 seconds and then only On Off indicator will remain on the remote controller display thereafter Ifyou press the Power I button on the indoor unit after setting the On Off timer from the remote controller Timer indicator on the indoor unit display will disappear and the On Off timer will be cancelled Even though the On Off timer is cancelled On Off indicator on the remote Setting Off timer Auto controller will remain displayed
60. ler or service center Do not clean the inside of the air conditioner by yourself For cleaning inside the appliance contact your nearest service center gt When cleaning the internal filter refer to the descriptions in the Cleaning the air conditioner section Failure to do may result in damage electric shock or fire English 11 A3050 EE Good IB amp IM_DB68 05270A_EN indd 11 2015 4 3 11 42 32 Checking before use I Operation ranges The table below indicates the temperature and humidity ranges the air conditioner can be operated within Refer to the table for efficient use Mode le NES Cooling 16 C 32 C 15 C 46 C Relative humidity 80 or less Heating 8 C 27 C 25 C 24 C Dry 18 C 32 C 15 C 46 C gt Ifthe air conditioner operates in cooling mode for long period of time in high humidity area dew may be formed gt If the outdoor temperature goes down to 5 C heating capacity may decrease as much as 60 70 of specified capacity according to the using conditions I Maintaining your air conditioner Internal protections via the unit control system D This internal protection operates if an internal fault occurs in the air conditioner amp Type Description Against cold air The internal fan will be off to prevent cold air when the heat pump is heating The internal fan will be off to defrost ice when the heat pum
61. lter every 2 weeks Cleaning term may differ depending on the usage and environmental NOTE conditions In dusty area clean it once a week Ifthe Air filter dries in a confined or humid area odors may generate If it occurs re clean and dry it ina well ventilated area English 31 A3050 EE Good IB amp IM_DB68 05270A_EN indd 31 2015 4 3 11 42 42 BRENT CON NE Cleaning the air conditioner Reassembling the Air filter 1 Put the filter on the main body and insert the hooks which are in the top of the Air filter into the the main body D Air filter 2 There s one hook in both side of the filter press the surface of the Air filter softly and get the hooks into the main body 3 Press the bottom of the filter lightly to securely fix the main body English 32 A3050 EE Good IB amp IM_DB68 05270A_EN indd 32 2015 4 3 11 42 42 Maintaining the air conditioner If the air conditioner will not be used for an extended period of time dry the air conditioner to maintain it in best condition 1 Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and cut off the power supply There may be internal damage if moisture is left in components a 2 Be
62. ng or extending the pipe 6 Align the pipes to connect them easily Tighten the flare nuts first with your hands and then with a torque wrench applying the following torque Hac Outer Diameter iene Nem kgfecm 06 35 mm 14 18 140 180 D 7 99 52 mm 34 42 350 430 912 70 mm 49 61 500 620 Indoor outlet pipe Connecting pipe 215 88 mm 68 82 690 830 Excessive torque can be cause of gas leakage If extending pipe by welding brazing please ensure nitrogen is Note used during welding brazing process The joint must be accessible and serviceable 7 For further details on how to connect to the outdoor unit and evacuate the air refer to page 53 55 Tighten the flare nut with torque wrench according to specified method If the flare nut is over tightened the flare may break and cause refrigerant gas leakage CAUTION English 50 A3050 EE Good IB amp IM_DB68 05270A_EN indd 50 2015 4 3 11 42 49 ZS EU Installing and connecting the drain hose of the indoor unit When installing the drain hose for the indoor unit check if condensation draining is adequate When passing the drain hose through the 65 mm hole drilled in the wall check the followings Wall o N Z 2 0 Z 2 0 gt Indoor unit 3 Drain hose 2 The drain hose must NOT The end of the drain hose The drain hose must not slant upwards must NOT be placed under be bent water After completing the installation of
63. on the bottom part ofthe indoor unit as shown in the illustration and it is fastened with screws Remove the Cap screw first and unfasten the screws so that you can disassemble the cover panel lt Unfasten the screw gt English 43 A3050 EE Good IB amp IM_DB68 05270A_EN indd 43 2015 4 3 11 42 46 ZS NE Disassembling Assembling the Cover panel for indoor unit installation Removing the Cover panel Before mounting the indoor unit The bottom panel fits the main body using the side center and bottom hooks as shown Unlock the side hooks first and then unlock the center and bottom hooks Check the location of the hooks before removingthecoverpane Location of the hooks on the central part Number and location of the hooks Center hook Bottom hook For specific Hook location and quantity please refer to cover panel with indicating arrows based on physical goods gt Removing the hooks on the central part Caution fragile Caution fragile Gently press the both side of the cover Use both hands panel inwards and release the hooks _ fs on both sides Release each hook by pushing it up at an angle Assembling the Cover panel After mounting the indoor unit To assemble the Cover panel proceed in reverse order of disassembling Use both hands for assembling and be extra careful not to damage the pipes and drain hose Lock the sid
64. ons provided in the wiring diagram included in the manual gt Always verify that electric connections cable entry section of leads protections are compliant with the electric specifications and with the instructions provided in the wiring scheme Always verify that all connections comply with the standards applicable to the installation of air conditioners Choosing the installation location Indoor unit gt For Wi Fi Air conditioner installation select indoor unit location near to wireless router In case Wi Fi signal strength weakened Smart APP may be disconnected depending on the Wi Fi signal strength gt Where airflow is not blocked Where cool air can be distributed throughout the room Install the refrigerant piping length and the height difference of both indoor and outdoor units as indicated in the installation diagram Wall that prevents vibration and is strong enough to hold the product weight Out of the direct sunlight 1 m or more away from the TV or radio to prevent the screen from being distorted or noise from being generated As far away as possible from the fluorescent and incandescent lights so that the remote controller can be operated well A place where the air filter can be replaced easily Don t install directly above electronics equipment as leaking water may cause damage if not serviced eg Computers TV etc vv vvv vv v English 37 A3050 EE Good IB amp IM_DB68 05270A_EN indd 37
65. operating in Cool mode 1 Press the Options button 2 Press the or Options button until 2 Step indicator starts to blink 3 Press the SET button to set the 2 Step Cooling function 2 Step 2 Step indicator will be displayed on the remote controller display and 2 Step Cooling function will begin SNOILdO 70 gt Press the Options button gt Press the lt gt or Options button to Cancel make the 2 Step indicator blink and press the SET button Remote controller display English 23 A3050 EE Good IB amp IM_DB68 05270A_EN indd 23 2015 4 3 11 42 37 RME a foe Using the Fast function You can set the Fast function to provide fast and powerful cooling heating When the air conditioner is operating in Cool Heat mode 1 Press the Options button 2 Press the Q C or Options button until Fast indicator starts to blink 3 Press the SET button to set the Fast function Fast Fast indicator will be displayed on the remote controller display and Fast function will begin gt Press the Options button Press the or Options button to Te make the Fast indicator blink and press the SET button Fast function is only available in Cool Heat mode NOTE Vertical air swing can be adjusted Set temperature and fan speed cannot be adjusted If the Fast function is selected while 2 Step Cooling Comfort Single user Quiet good sleep function is on c
66. orresponding function will be cancelled When you select Fast function in Heat mode you may not be able to increase fan speed in order to prevent any cool air from blowing Remote controller display Using the Comfort function You can set the Comfort function to provide mild cooling heating When the air conditioner is operating in Cool Heat mode 1 Press the Options button 2 Press the Q C or Options button until Comfort indicator starts to blink 3 Press the SET button to set the Comfort function Comfort Comfort indicator will be displayed on the remote controller display and Comfort function will begin gt Press the Options button Press the gt or Options button to l 2 make the Comfort indicator blink and press the SET button Comfort function is only available in Cool Heat mode NOTE Vertical air swing can be adjusted Set temperature can be adjusted but fan speed cannot be adjusted Cool Set 11 Ifthe Comfort function is selected while 2 Step Cooling Fast Single user Quiet good sleep function is on corresponding function will be cancelled TEN Comfort Remote controller display English 24 A3050 EE Good IB amp IM_DB68 05270A_EN indd 24 2015 4 3 11 42 38 E o A LUE Using the Single User function This function will reduce the energy usage while the air conditioner is operating in Cool Heat mode When the air conditioner is opera
67. p is heating Defrost cycle pos f Vertical air flow blade will be closed during defrost cycle and it will open again during heating operation after defrost cycle Protect compressor The air conditioner does not start operating immediately to help protect the compressor of the outdoor unit after it has been started Ifthe heat pump is operating in Heat mode defrost cycle is actuated to help remove frost from an outdoor NOTE unit that may have deposited at low temperatures The internal fan is switched off automatically and restarted only after the defrost cycle is completed Smart install gt Through Smart install function installer can check if the installation was done properly gt If the installation was not done properly error indicator will turn on the indoor unit display Therefore user will know if the installation was done properly or not A3050 EE Good IB amp IM_DB68 05270A_EN indd 12 English 12 2015 4 3 11 42 32 Zo o Eu Checking the name of the parts Your air conditioner may slightly look different from illustration shown below depending on your model I Main parts Room temperature sensor NOILDNNA DISV4 ZO D DiE Wi Fi module Air filter Air intake Vertical air D flow blades Horizontal air flow blade I Display gt ED
68. page Cut insulation to 57 for further details have rainwater drained 15 m as maximum pipe length and 3 m as minimum pipe length CAUTION lt will reduce noise and vibration 8 meters Make an U trap A on the f pipe which is connected 15 meters maximum maximum caution tothe indoor unit at outer total pipe length total pipe wall and cut the bottom height part of the insulation about 10 mm to prevent rainwater from getting inside through the insulation However be careful not to damage the pipe Make at least one round It will reduce noise and vibration Kk The appearance of the unit may be different from the diagram depending on the model English 38 A3050 EE Good IB amp IM_DB68 05270A_EN indd 38 2015 4 3 11 42 43 I Recommended Space Requirements for the Outdoor Unit When installing 1 outdoor unit Figure Description Top view Side view Air intake Air outlet 4 Air intake Air outlet e 4 Air flow direction Installation minimum be done above 500 mm from the ground must Snow proof hood installation is recommended for heavy snowing region recommend For low ambient model Unit mm 300 or more Snow proof hood Wall Mounting Bracket x least 500 When the air outlet is opposite the wall When the air outlet is towards the wall U LLLLLLLLLLL Y Y D U 2 g ES 2 L t i m Q E U U OII blocked
69. pes Unscrew the caps English 48 A3050 EE Good IB amp IM_DB68 05270A_EN indd 48 amp 2015 4 3 11 42 49 Cutting or extending the pipe The length ofthe pipe can be Extended up to see table page 38 Shorten up to see page 38 If you need a pipe longer than 5 meters You must add refrigerant to the pipes otherwise the indoor unit may freeze 1 Make sure that you have all the required tools pipe cutter reamer flaring tool and pipe holder 2 Ifyou want to shorten the pipe cut it using a pipe cutter ensuring that the cut edge remains at 90 with the side of the pipe see below examples of correct and incorrect cut edges Oblique x Burr 3 To prevent a gas leak remove all burrs at the cut edge of the pipe using a reamer NOILVTIVISNI ZO A Face the pipe down while removing the burrs to make sure that burrs do not get in to the pipe CAUTION 4 Puta flare nut slightly into the pipe and modify the flare 0 7 Outer Diameter D Depth A Flaring Size B 4542 06 35 mm 1 3mm 8 7 9 1 mm Bro 99 52 mm 1 8 mm 12 8 13 2 mm NZ 012 70 mm 20mm 16 2 16 6mm R0408 915 88 mm 2 2 mm 19 3 19 7 mm 5 Check if you flared the pipe correctly see examples of incorrectly flared pipes below Correct Inclined Surface English 49 A3050 EE Good IB amp IM_DB68 05270A_EN indd 49 amp Damaged Cracked Uneven Thickness 2015 4 3 11 42 49 Cutti
70. progress 88 Display Progress will be diplayed in 0 99 LED Display Indicator on the indoor unit display will blink in sequence and then all indicators will blink This will be repeated TYPE 88 Display LED Display RE Ka O ui Indoor unit indicator UK UK O LED2 len O LED3 CR o EEE Display may be different depending on the model 3 Smart Install mode will end 1 Smart Install mode will take approximately 7 13 minutes Actual time may be different depending on the model 2 When Installation is successful Smart Install mode will end with ringing sound and the air conditioner will be in standby status Error message will not be displayed on the indoor unit indicator and the remote controller and buttons on the indoor unit will work normally 3 When installation is not successful Smart Install mode will end and error message will be displayed on the indoor unit display A CAUTION 1 Take necessary measures when error occurs Refer to the service manual for necessary measures for each error that occurs 2 Use the product after taking care of the error that occurs there s error is occurred on outdoor unit Check the LED display on outdoor unit for the details For Inverter model only Error indicator LED Display LED 1 LED2 LED 3 Error Measures to take by an installer 8 8 Display l A o Le o e ISIS Commnuication Er
71. r few seconds and disappears WiFi function will begin SONILLAS SO 2 Press the Settings button to set the WPS function Press the Settings button for 4 seconds Ti will blink first then disappears and WPS function will begin For detail information please refer to Smart A C application manual Note Smart A C application may not be available for some models Remote controller display English 29 A3050 EE Good IB amp IM_DB68 05270A_EN indd 29 2015 4 3 11 42 41 ZS CON NE Cleaning the air conditioner Make sure to turn off the power of the indoor unit and cut off CAUTION the power supply before cleaning the air conditioner I Cleaning the indoor unit gt Wipe the surface of the unit with a slightly damp micro fiber cloth when needed Contact the service center when you clean the indoor unit heat exchanger because it needs to be disassembled Since the panel of the indoor unit is easily scratched you should use a micro fiber cloth to clean the panel When you use the micro fiber cloth slightly dampen the cloth and remove any debris on the cloth to avoid scratches Do not clean the display using alkaline detergent CAUTION Do not use sulfuric acid hydrochloric acid organic solvents such as thinner kerosene and acetone etc to clean the surface of the product or put any stickers on it They may damage the surface of the air cond
72. r Diameter q indoor unit unless you connect the pipe directly from the rear Nem kgfecm 2 Smooth the cut edges 96 35 mm 14 18 140 180 3 Remove the protection caps of the pipes and connect the assembly 352MM re ee pipe to each pipe Tighten the nuts first with your hands and then with 912 70 mm 49 61 500 620 a torque wrench applying the following torque 015 88mm 68 82 690 830 B Ifyou want to shorten or extend the pipes refer to page 49 50 NOTE 4 Cutoff the remaining foam insulation 5 If necessary bend the pipe to fit along the bottom of the indoor unit Then pull it out through the appropriate hole The pipe should not project from the rear of the indoor unit The bending radius should be 100 mm or more 6 Pass the pipe through the hole in the wall 7 For further details on how to connect to the outdoor unit and evacuate the air refer to page 53 55 The pipe will be insulated and fixed permanently into position after finishing the installation and the gas leak test Note referto page 57 for further details Tighten the flare nut with torque wrench according to specified method If the flare nut is over tightened the flare may break and cause refrigerant gas leakage DO NOT WALL UP THE PIPE CONNECTION All refrigerant pipe connection must be easy accessible and serviceable CAUTION English 47 A3050 EE Good IB amp IM_DB68 05270A_EN indd 47 2015 4 3 11 42 49 Zl fos
73. r more Ifinstallation is done in inappropriate space unit may generate sound and cause bad effect on the product CAUTION Accessories The following accessories are supplied with the air conditioner The number of each accessory is indicated in parentheses NOTE Accessories in the indoor unit case Installation must be done in level and in a place where vibration will not cause any effect Installation Plate 1 Remote controller 1 Batteries for Remote User s amp Installation Wi Fi Manual 1 A3050 EE Good IB amp IM_DB68 05270A_EN indd 40 controller 2 Manual 1 I amp LH Remote Holder a a b Cap Screws 2 Guide Right 1 Guide Left 1 m LE AtA English 40 2015 4 3 11 42 44 Accessories in the outdoor unit case 2 wire 3 wire Assembly Cable 1 Assembly Cable 2 Drain Plug 1 Rubber Leg 4 5 N A Ee gt K8 a 3 2 Theflare nuts are attached to the end ofeach pipe ofan evaporator or a service port NOTE Use the nuts when connecting the pipes The assembly cable is optional If it is not supplied use the standard cable The drain plug and rubber leg are only included when the air conditioner is supplied without the assembly pipe as seen in the picture below I Optional accessories The following connection accessories are optional
74. ror 1 Check the connection wire between indoor and Eid O Q between Indoor and outdoor unit whether the power cable and outdoor unit commnunication cable is crossed or not ED Error on indoor 1 Check the connection of the connector ies temperature sensor Error on indoor heat 1 Check the connection of the connector t t E ide E 123 Q O exchanger 1 Check the connection of the connector E 154 O O Q Error on indoor fan motor 2 Remove foreign substance Check for the cause that restrains motor g8 display and all 1 Re set options LED blinks o o o EEPROM Option error E 6 163 1 Check if the service valve is completely open Refri t flow blocking 2 Check if there s any blockage in the refrigerant E4e oO i E E pipe which connects indoor and outdoor unit 3 Check for refrigerant leak e O Q 1 Check if sufficient amount of additional refrigerant was charged for the pipe length that E554 k Above LED pattern is displayed when Lack of Refrigerant exceeds 7 5m 2 Check for refrigerant leak between valve and pipe connection O 0ff Blinking On English 59 A3050 EE Good IB amp IM_DB68 05270A_EN indd 59 NOILVTIVISNI ZO 2015 4 3 11 42 53 A3050 EE Good IB amp IM_DB68 05270A_EN indd 60 Final check and trial operation To complete the installation perform the following checks and tests to ensure that the air conditioner operates correctly Check the followings Strength of t
75. s appliance only In addition do not use an extension line D Extending the power line may result in electric shock or fire Do not use an electric transformer It may result in electric shock or fire gt Ifthe voltage frequency rated current condition is different it may cause fire The installation of this appliance must be performed by a qualified technician or service company Failing to do so may result in electric shock fire explosion problems with the product or injury and may also void warranty on the installed product Install a Isolation Switch next to the Air Conditioner but not on the panels of the Air Conditioner and circuit breaker dedicated to the air conditioner Failing to do so may result in electric shock or fire Fix the outdoor unit firmly so that the electric part of the outdoor unit is not exposed Failing to do so may result in electric shock fire explosion problems with the product English 6 A3050 EE Good IB amp IM_DB68 05270A_EN indd 6 2015 4 3 11 42 31 ZS EU Do not install this appliance near a heater inflammable material Do not install this appliance in a humid oily or dusty location in a location exposed to direct sunlight and water rain drops Do not install this appliance in a location where gas may leak This may result in electric shock or fire Never install the outdoor unit in a location such as on a high external wall where it could fall
76. s normal Refer to the Service Manual for further details The remaining air in the Refrigeration cycle which contains moisture may cause malfunction on the compressor caution Always contact the service center or a professional installation agency for product installation English 54 015 88mm 68 82 690 830 A3050 EE Good IB amp IM_DB68 05270A_EN indd 54 2015 4 3 11 42 51 I Important information regulation regarding the refrigerant used This product contains fluorinated greenhouse gases covered by the Kyoto Protocol Do not vent gases into the atmosphere 1 Please fill in with indelible ink gt the factory refrigerant charge of the product gt the additional refrigerant amount charged in the field and gt the total refrigerant charge on the refrigerant charge label supplied with the product a Factory refrigerant charge of the product NOTE see unit name plate b Additional refrigerant amount charged in the field Refer to the above information for the quantity of refrigerant replenishment c Total refrigerant charge d Refrigerant cylinder and manifold for charging Refrigerant type GWP value The filled out label must be adhered in the proximity of the product charging port e g onto the inside of the stop valve cover CAUTION Charging the refrigerant under conditions of liquid by using a liquid pipe R 410
77. tically In Heat mode Adjusting air flow direction is available Temperature and fan speed change in good sleep mode Fall asleep Eases you into sleep by dropping the temperature Sound sleep Relaxes your body and raises your temperature slightly Wake up Allows you to wake up from comfortable intermittent air and it makes you feel refreshed Recommended set temperature is between 25 C 27 C for cooling and 21 C 23 C for heating If the set temperature is too low you may feel cold during sleep or catch a cold Optimal operation hour of good sleep mode is 8 hours Therefore if the time is set too short or long you may not feel as comfortable as you would expect If the good sleep mode is set over 5 hours Wake up stage will begin when 1 hour is remaining in the operation time and the air conditioner will stop automatically When the On timer and the good sleep function is set simultaneously the air conditioner will only apply the function that was set later English 22 A3050 EE Good IB amp IM_DB68 05270A_EN indd 22 2015 4 3 11 42 37 ZS CON NE 2 Step cooling function 2 Step Cooling function will set the air conditioner to cool the room quickly to reach the set temperature when the indoor temperature is higher than the set temperature and then the air conditioner will automatically operate in Dry mode when indoor temperature reaches set temperature When the air conditioner is
78. ting in Cool Heat mode 1 Press the Single user button Single user indicator will be displayed on the remote controller display Then __ will be displayed on the set temperature indicator part for few seconds and Single user function will begin When the Single user function is on vertical air swing will turn on automatically Ifthe current set temperature is lower than 24 C in Cool mode it will be automatically raised to 24 C SNOILdO t0 Cancel gt Press the Single user button once again Cool Single user function is only available in Cool Heat mode NOTE If the Single user function is selected while 2 Step Cooling Fast Comfort Quiet good sleep function is on corresponding function will be cancelled Vertical air swing will remain on even after the Single user function is cancelled Select or cancel the Single User function with the Options button Press the Options button press the or Options button to make Single user indicator blink and press the SET button Remote controller display Additional options available in Single user function Single user You can adjust the set temperature by 1 C within the range of 24 C 30 C in Cool mode and 8 C 30 Cin Heat mode 2 Auto Low 2 Med 2 High 2 Turbo can be selected Vertical air swing can be selected English 25 A3050 EE Good IB amp IM_DB68 05270A_EN ind
79. tioner D Take special care that children do not injure themselves by inserting their fingers into the product amp Do not strike or pull the air conditioner with excessive force amp This may result in fire injury or problems with the product Do not place an object near the outdoor unit that allows children to climb onto the machine This may result in children seriously injuring themselves Do not use this air conditioner for long periods of time in badly ventilated locations or near infirm people P Since this may be dangerous due to a lack of oxygen Open a window at least once an hour Ifany foreign substance such as water has entered the appliance cut off the power supply and contact the nearest service center gt Failing to do so may result in electric shock or fire Do not attempt to repair disassemble or modify the appliance yourself gt Do not use any fuse such as cooper steel wire etc other than the standard fuse gt Failing to do so may result in electric shock fire problems with the product or injury English 9 A3050 EE Good IB amp IM_DB68 05270A_EN indd 9 2015 4 3 11 42 32 Safety precautions FOR USING CAUTION Do not place objects or devices under the indoor unit gt Water dripping from the indoor unit may result in fire or property damage example electrical appliances Check that the installation frame of the outdoor unit is not broken at least once
80. uter Torque Diameter Nem kgf cm Make the electrical connection and leave the system into stand by easmm 1418 140 180 mode Do not turn on the system 99 52 mm 34 42 350 430 This is necessary for better vacuum operation full OPEN position of Electronic Expansion Valve EEV 12 70mm 49 61 500 620 3 Connect the charging hose of the low pressure side of manifold gauge to a gas service port as seen in the picture Manifold gauge 4 Open the valve of the low pressure side of manifold gauge counterclockwise 5 Evacuate the air in the connected pipes using the vacuum pump for about 15 minutes Gas service port gt Make sure that pressure gauge shows 0 1 MPa 76 cmHg after about lt Lowipressure gt 10 minutes d This procedure is very important to avoid a gas leak gt Close the valve of the low pressure side of manifold gauge clockwise gt Turn off the vacuum pump I Vacuum gt Check for 2 minutes if there is any pressure change Liquid service port Pump gt Remove the hose of the low pressure side of manifold gauge lt High pressure gt ie prevention 6 Set a valve cork of liquid and gas service port to the open position Adding Refrigerant Add refrigerant charge according to table below If you use a pipe longer than 5 m 15 g of refrigerant R 410A must be added for each extra meter If you use a pipe shorter than 5 m The evacuate time i
81. utton to check the power consumption 3seconds after setting power consumption checking function Usage indicator on the remote controller will disappear Indoor unit will display the amount of Power consumption for few seconds and then return to usual status by displaying the set indoor temperature Power consumption will be calculated from the moment the air conditioner is turned on and calculated value will be reset when the air conditioner turns off 0 1 is the default value of the electricity consumption and 99 is the maximum value Unit is in kWh When the air conditioner is not operating power consumption will not be displayed on the indoor unit display Indoor unit display English 27 A3050 EE Good IB amp IM_DB68 05270A_EN indd 27 2015 4 3 11 42 40 MEME a oo Setting the Beep sound Beep sound from the indoor unit can be muted 1 Press the Settings button 2 Press the or Settings button until Beep indicator starts to blink 3 Press the SET button to mute the beep sound 3seconds after setting Beep sound function Beep indicator on the remote controller display will disappear and Beep sound function will begin Resetting the Filter clean reminder When Filter clean reminder CF lights up on the indoor unit display clean the filter and reset the reminder by following this instruction 1 Press the Settings button 2 Press the or Settings button until Filt
82. y for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry z gt Our units must be installed in compliance with the spaces indicated in the installation manual to ensure either accessibility 2 from both sides or ability to perform routine maintenance and repairs The units components must be accessible and that can be disassembled in conditions of complete safety either for people or things For this reason where it is not observed as indicated into the Installation Manual the cost necessary to reach and repair the unit in safety as required by current regulations in force with slings trucks scaffolding or any other means of elevation won t be considered in warranty and charged to end user Power supply line fuse or circuit breaker gt Always make sure that the power supply is compliant with current safety standards Always install the air conditioner in compliance with current local safety standards gt Always verify that a suitable grounding connection is available Verify that the voltage and frequency ofthe power supply comply with the specifications and that the installed power is sufficient to ensure the operation of any other domestic appliance connected to the same electric lines Always verify that the cut off and protection switches are suitably dimensioned gt Verify that the air conditioner is connected to the power supply in accordance with the instructi

Samsung AR09HSFSPWKN Lietotāja rokasgrāmata

Contents

Download Pdf Manuals

Related Search

Related Contents