Home

Samsung AW05MDYEA/XFO User Manual

1. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 If the indicator is not displayed at the top of the control panel press the button on the control panel one or more times until it appears Result The unit beeps each time you press the button The air conditioner runs in Dry mode gt You can change modes at any time The passes through the control panel 3 3 To adjust the temperature press the C or C _ buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Temp Result Each time you press the C or C buttons The temperature is adjusted by 1 C The unit beeps The air conditioner starts removing the excess humidity the quantity of air is adjusted automatically oO 4 To control the direction of the air flow refer to page 9 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room you can adjust the orientation of the inner air flow blades on the unit Adjust the air flow blades to the desired position by pushing them side to side Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given time You can se
2. eg OWNER S INSTRUCTIONS AWO5MDYEA Safety Precautions The following safety precautions must be taken when installing and using your air conditioner 1 The air conditioner must be plugged into its own specific power source which must be installed in compliance with national wiring earthing and safety regulations Depending on national regulations and your specific installation you may need to install A circuit breaker For further information on electrical requirements contact a professional electrician This device must be installed according to the national electrical rules 2 Make sure that the unit is correctly ventilated at all times do NOT place clothing or other materials over it 3 NEVER spill liquids of any kind into the unit Should this happen unplug the unit and contact your installation specialist 4 Do NOT insert anything between the air outlet blades as it may damage the inner fan and you may be hurt Keep children away from the unit 5 Ifthe supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard 6 Do NOT attempt to repair the unit yourself If it is damaged in any way contact An authorized service center The dealer from whom you purchased the air conditioner 7 Do NOT place any blocking objects in front of the unit 8 Ifthe remote control will not be used for a long time remove the batteries 9 Befor
3. a series of step by step procedures for each function available The illustrations in the step by step procedures use four different symbols r gt IMPORTANT NOTE Cooling Your Room You must select the Cool mode if you wish to lower the temperature in your room You can also set the Fan speed 1 Press the On Off button Result The air conditioner starts up in the mode selected when the unit was last used The unit beeps twice The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 If the temperature is not displayed on the control panel Press the button on the unit one or more times until the temperature is displayed Result The unit beeps each time you press the button The air conditioner starts up in the Cool mode gt You can change modes at any time 3 To adjust the temperature press the C or C _ buttons on the unit one or more times until the desired temperature is displayed The temperature can be set between 18 C and 30 C Result Each time you press the Jor _ buttons The temperature is adjusted by 1 C and displayed on the control panel The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature 4 To set the fan speed Press the button on
4. 00 00095 0 900 0009590 000006 gt If the wall is greater than 110mm thick cut the wall back on a 45 angle if possible 00020020 0 00200 0 0 00900 T O0Q80O20 0 K0Q0O20 0 Oo Outdoor side OOO of OoOo OO 00 099 25 0O o O20 Ce OS O oO oO Oo Oo 100mm or more Install an adhesive bottom gasket to prevent air and insects from getting into the room 1 Strip an adhesive bottom gasket off 2 Seal an adhesive bottom gasket to the bottom of the air conditioner RN XG Adhesive bottom gasket THIS AIR CONDITIONER IS MANUFACTURED BY a ELECTRONICS Printed in China
5. 000sss0Bnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnenee nennen 14 a Solving Common Problems sisseseade iiaa eee 15 Technical Specitications au ae 15 INSTALLATION Description of Each Component Air outlet Inner air flow blades right left orientation Air outlet AN W Ft tow P2 Med NY WOT Outer air flow blades SY Air inlet Outside Air inlet Inside LU gt F amp Adhesive bottom gasket Refer to page 17 Power plug The type of power plug may differ depending on the local power supply Energy Saver Temperature indicator Timer settings Energy Saver an pm Temperature adjustment button Timer setting button Zum Timer Timer indicator buttons Fan speed te Speed Mode selection button adjustment button P Cool Fan Dry 7 Meh Sleep timer setting button On Off button Getting Started You have just purchased a Samsung window type room air conditioner which should be installed following your installation manual Your Owner s Instructions contain much valuable information on using your air conditioner Please take the time to read them as they will help you take full advantage of the unit s features The booklet is organized as follows The following figures are shown on pages 4 Description of Each Component They will help you find the buttons and understand the symbols displayed Inthe manual you will find
6. air conditioner has not been triggered Check that the power cable is plugged into a wall socket and the socket is switched on if necessary Check that the temperature indicator on the unit is lit if necessary press the On Off button on the remote control or unit Check that there are no obstacles between you and the unit Replace the remote control batteries if necessary Check that you are close enough to the unit seven metres yards or less Check that you are pointing the remote control at the remote control sensor on the unit Replace the remote control batteries if necessary Check that the correct operating mode has been selected Cool The room temperature may be too low Dust may be blocking the air filter refer to page 16 for cleaning instructions Check that there is no obstacle blocking the air flow into or out of the unit Check that the timer has been programmed correctly refer to page 10 12 Ventilate the room Technical Specifications Design and specifications are subject to change without notice Power Supply 220 240V 50Hz gt Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency This condition belongs to the above model Installation Before installation be sure to check the installation area or the air conditioner and drain hose Checkpoints prior to installation 1 Check the cabinet and front grill
7. displayed F1 Low The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner will be controlled as illustration below Cooling When the temperature has been increased by 1 C after 1 hour it is maintained for 7 hours To Cancel the Sleep Timer To cancel the timer press The button on the unit Energy Saver Timer Result The unit beeps The SLEEP indicator is no longer displayed FI Low The air conditioner operates in the mode selected last F2 Med F3 High gt If you select the Energy Saving mode in the Sleep Timer mode the Sleep Timer will be cancelled and the air conditioner will start up in the Energy Saving mode Selecting Energy Saving Mode If you wish to save energy when using your air conditioner select the energy saving mode 1 To select the energy saving mode press the button on the unit one 2H or more times until the Energy Saver indicator lights up EN Result The fan and compressor cycle on and off together The fan will continue to run for a short time after the compressor cycles off F2 Med F3 High gt if you would like the air conditioner to run in Fan mode do not press the button You cannot use the Fan mode in the energy saving mode 2 To stop the energy saving mode press the button on the unit again Result The fan runs at all times while the compressor cycles on and off
8. e of the unit for any harmful defects such as scratches 2 Be sure to check the power supply Refer to the specifications on the label attached to the unit Installation Conditions 1 Asthe unit is heavy the wall or window of the installation area should have sufficient strength and durability for operation of the air conditioner and for prevention of any vibration or noise If it is weak reinforcement work should be performed separately 2 lt is advisable to install the air conditioner in the north or west side to prevent the effect of direct sunlight When installing it in the south or east side due to unavoidable circumstances it is advisable to install the sunshade to prevent the direct sunlight In this case take care not to cause any hindrance to the flow of outside air 3 When installing the air conditioner be sure to obtain sufficient space on the rear side of the unit for smooth flow of air When operating the air conditioner in closed areas such as inner building with cooling operation and result in trouble with the unit See the illustration below O oC 00 00 pene O O oO Fence wall or other obstacle OoO O los 06066 O Q Approx 3 90 0 a u O 00 00 Q oO Oo 750mm 110mm min 0 D 00 ne O 900 0 0 Q0800 VU Er J 000 000 590900 000989 Oo 0 0090 0000500
9. e throwing out the device it is necessary to pull back the battery cells and get rid of them safely 10 The appliance is not intended for use by young children or infirm person without supervision young children should be supervised to ensure that they do not play with the appliance 11 Do NOT use an extension cord with this product CAUTION The manufacturer does not assume responsibility for accidents or injury caused by an incorrectly installed air conditioner If you are unsure about installation contact an installation specialist Contents PREPARING YOUR AIR CONDITIONER BM Salet Precautions esse 2 m Description of Each Component uuuuuseseennnnenennnnnnnnnennnnnnnnnnnnennnnnnnee nennen 4 u Gennio Sltamed oon 2k sa otis hese eta eee 5 OPERATING YOUR AIR CONDITIONER OOlING YOUN ROOM ausser ea 6 Mi ANNO VOU ROON een daa ee eee 7 u Removing Excess HUMIAIY anne ea 8 m Adjusting the Air Flow Direction Horizontally cccccccecsssseeeeeeeeseeseeeeeeeeeees 9 PROGRAMMING YOUR AIR CONDITIONER By Seting he ON TIMER unseren 10 m Setting the Off TIMEN seee a a e RER 11 m Setting the Sleep Timer sanesna a a nennen 12 m Selecting Energy Saving Mode eeeennnenneeesennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnenne nennen 13 RECOMMENDATIONS FOR USE m Temperature and Humidity Ranges c cccccccsseccecessseecceeeeeeeeeeseeeesseeeeeeees 13 m Cleaning Your Air Conditioner 22uu
10. er operates in the Cool mode 1 Check that the air conditioner has been switched on if necessary press the On Off button 2 Set the operating time by pressing the button on the unit one or more times until the desired time is displayed The operating time can be set between 1 and 24 hours Result Each time you press the button The time is adjusted by 1 hour and displayed on the control panel The unit beeps The operating time is displayed and decreases automatically to indicate the remaining time The air conditioner switches off automatically when the operating time reaches zero gt You can select the fan speed temperature and Energy saving mode after setting the On timer and Off timer mode However when you change the mode the On timer and Off timer mode is canceled To Cancel the Off Timer To cancel the timer press The button on the unit one or more times until is displayed or The On Off button on the unit Setting the Sleep Timer The Sleep Timer can be used when you are cooling your room to switch the air conditioner off automatically after 8 hours gt If you wish to switch the unit off at a specific time refer to page 11 1 Make sure that you have selected the Cool mode 2 Press the button on the unit Result Each time you press a button the unit beeps The SLEEP passes through the control panel for about 15 seconds and the Ei will be
11. gt if you select the Sleep Timer in the Energy Saving mode the Energy o Saving will be cancelled and the air conditioner will start up in the Power Sleep Timer mode Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used Mode Indoor Temperature Outdoor Temperature Indoor Humidity Cooling 21 C to 32 C approx 21 C to 43 C approx 80 or less If the air conditioner is used at Then Higher temperature The automatic protection feature may be triggered and the air conditioner stopped Lower temperature A water leakage or some other malfunction may happen if the heat exchanger freezes Higher humidity levels Water may condense on and drip from the surface of the unit if it is used for long periods Cleaning Your Air Conditioner Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time gs When cleaning the air conditioner turn it off and pull out the power plug u N SG CK Open the front grille by pulling the tabs on both sides of the grille Then lift it up slightly to open the front grille completely 2 Grab the tabs on the filter and pull i
12. lect the On timer only when the air conditioner is off You can select the On timer only when the air conditioner operates in the Cool mode 1 Check that the air conditioner has been switched off if necessary press the On Off button yi 2 Set the operating time by pressing the button on the unit one or more times until the desired time is displayed The operating time can be set between 1 and 24 hours Result Each time you press the button The time is adjusted by 1 hour and displayed on the control panel The unit beeps The operating time is displayed and decreases automatically to indicate the remaining time The air conditioner starts up in the Cool mode automatically when the operating time reaches zero gt gt You can select the fan speed temperature and Energy saving mode after setting the On timer and Off timer mode However when you change the mode the On timer and Off timer mode is canceled To Cancel the On Timer Be i To cancel the timer press as The button on the unit one or more times until is displayed or The C On Off button on the unit The air conditioner operates in the mode selected when the unit was last used Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given time You can select the Off timer only when the air conditioner is on You can select the Off timer only when the air condition
13. t up and out 3 Remove all dust on the air filter with a vacuum cleaner or brush 4 When you have finished insert the air filter back into its original position amp N gt 5 Wipe the surface of the unit with a neutral detergent and then wipe it again ie with dry cloth Be sure not to use benzene solvent or other chemical products gt If you Then Will not be using the air conditioner for a long period of time Have not used the air conditioner for a long period of time Set the fan to F1 and let it for a few hours to dry the inside of the air conditioner thoroughly Switch the air conditioner off and unplug it from the wall socket Clean the filter and outer surfaces Set the fan to F1 and let it run for a few hours to dry the inside of the air conditioner thoroughly Solving Common Problems Before contacting an authorized service center perform the following simple checks They may save you the time and expense of an unnecessary call Problem The air conditioner does not operate at all The air conditioner does not operate with the remote control No beep is heard when you press the On Off button on the remote control The air conditioner does not cool The timer is not correctly triggered Odors are permeating the room during air conditioning Model AWOSMDYEA Explanation Solution rs 4 Check that the circuit breaker used for the
14. the unit one or more times until the desired Fan speed F1 F2 or F3 is displayed rt Low I Medium F3 High 5 To control the direction of the air flow refer to page 9 Airing Your Room If you want to provide air circulation without cooling you can use the Fan mode 1 If necessary press the I On Off button Result The air conditioner starts up in the mode selected when the unit was last used The unit beeps twice 2 If the fan speed F1 F2 or F3 is not displayed on the control panel Press the button on the unit one or more times until the fan speed F1 F2 or F3 is displayed Result The unit beeps each time you press the button The air conditioner starts up in Fan mode gt You can change modes at any time When the air conditioner is in the Fan mode the temperature cannot be set or displayed 3 To set the fan speed Press the button on the unit one or more times until the desired fan speed F1 F2 or F3 is displayed _ Low _ Z Medium FJ High 4 To control the direction of the air flow refer to page 9 Removing Excess Humidity If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much You can operate the Dry mode only by using the control panel 1 If necessary press the On Off button Result The air conditioner starts up in the mode selected when the unit was last used The unit beeps

Samsung AW05MDYEA/XFO User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents