Samsung AW122ZB – 1.0 T
Contents
1. OWNER S INSTRUCTIONS AW12ZKB AW18ZKC Window type Room Air Conditioner Cool DB98 30396A Safety Precautions The following safety precautions must be taken when installing and using your air conditioner 1 The air conditioner must be plugged into its own specific power source which must be installed in compliance with national wiring earthing and safety regulations Depending on national regulations and your specific installation you may need to install A circuit breaker For further information on electrical requirements contact a professional electrician This device must be installed according to the national electrical rules 2 Make sure that the unit is correctly ventilated at all times do NOT place clothing or other materials over it 3 NEVER spill liquids of any kind into the unit Should this happen unplug the unit and contact your installation specialist 4 Do NOT insert anything between the air outlet blades as it may damage the inner fan and you may be hurt Keep children away from the unit 5 ALWAYS ensure that the power cable is in good condition If the power cord is damaged in any way it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard 6 Do NOT attempt to repair the unit yourself If it is damaged in any way contact An authorized service center 4 The dealer from whom you purchased the air conditioner 7 Do NOT place any b2. 80 or less If the air conditioner is used at Then Higher temperatures The automatic protection feature may be triggered and the air conditioner stopped Lower temperatures A water leakage or some other malfunction may happen if the heat exchanger freezes Higher humidity levels Water may condense on and drip from the surface of the unit if it is used for long periods Installation Before installation be sure to check the installation area or the air conditioner and drain hose Checkpoints prior to installation 1 Check the cabinet and front grille of the unit for any harmful defects such as scratches 2 Be sure to check the power supply Refer to the specifications on the label attached to the unit Installation Conditions 1 As the unit is heavy the wall or window of the installation area should have sufficient strength and durability for operation of the air conditioner and for prevention of any vibration or noise If it is weak reinforcement work should be performed separately 2 It is advisable to install the air conditioner in the north or west side to prevent the effect of direct sunlight When installing it in the south or east side due to unavoidable circumstances it is advisable to install the sunshade to prevent the direct sunlight In this case take care not to cause any hindrance to the flow of outside air 3 When installing the air conditioner be sure to obtain sufficient space on the rear sid
3. will run as Wake Up stage for the last one hours before stop Dd To Cancel the Bio Sleep Mode If you no longer wish to use the Bio Sleep mode that you have set you Timer 1 Result can cancel it at any time Press the O button on the remote control or press the button on the unit to switch off the air conditioner To cancel a selected Bio Sleep mode you can also press the Esas mer or button on the remote control or press the l or button on the unit The unit beeps The 2 indicator is no longer displyed The air conditioner operates in the mode selected last If you select the Energy Saving mode in the Bio Sleep mode the Bio Sleep mode will be canceled and the air conditioner will start up in the Energy Saving mode Selecting Smart Saving Mode R c l If you wish to save smartwhen using your air conditioner pote vonda Control Panel select the smart saving mode with the Smart Saver button gt gt 1 To select the smart saving mode press the Smart Saver button on the remote control or unit one or more times until the Smart Saver indicator lights up Result The fan and compressor cycle on and off together 4 The fan will continue to run for a short time after the compressor cycles off If you would like the air conditioner to run in Fan mode do not press the Smart Saver button You cannot use the Fan mode in the saving mode 2 To stop the smart saving mode press the Smart Sav
4. Dust may be blocking the air filter refer to page 15 for cleaning instructions Check that there is no obstacle blocking the air flow into or out of the unit The air flow direction does not Check that the air conditioner has been switched on if necessary change when you press the press On Off on the remote control or unit button The timer is not correctly triggered Check that the timer has been programmed correctly see page 11 13 Odours are permeated in the Air the room room during air conditioning Technical Specifications Design and specifications are subject to change without notice Model No Power Supply Net Dim mm AW12Z 230V 50Hz W560XH370XD550 AW18Z W620XH425XD645 Note All specifications are as per rated condition i e Indoor temp 27 C and outdoor temp 35 C Current and power vary as the outdoor temperature vary Operating Recommendations Here are a few recommendations that you should follow when using your air conditioner Topic Recommendation Power failure If a power failure occurs when the air conditioner is operating the unit is switched off When the power returns the air conditioner starts up again automatically Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used Mode Indoor Temperature Outdoor Temperature Indoor Humidity Cooling 21 C to 32 C approx 21 C to 54 C approx
5. e of the unit for smooth flow of air When operating the air conditioner in closed areas such as inner building with cooling operation and result in trouble with the unit See the illustration below 9 The appliance must be fixed well by screw or similar method Awning Fence wall or other obstacle Approx 3 750mm 150mm min gt 4 If the wall is greater than 150mm thick cut the wall back on a 45 angle if possible se Indoor Side 100mm or more Installation of the Drain Tube Fix the drain tube as shown in the figure Installation of the Drain Pan a The procedure for installing the drain pan should be determined by the od las condition of the installing area Screws 2EA 4 In the case of an area where the drain pan can not be directly installed on the rear side of the unit after installing the air conditioner Example High storage 1 Open the front grill refer to page 16 2 Remove the screw located at the lower section of the front grille It is secured in the gt section depending on the model 3 Remove the front panel 3 1 Press both sides of the cabinet in the direction of the arrow as shown in the figure 3 2 Pull the lower part of the front panel sl
6. er button on the remote control or unit again Result The fan runs at all times while the compressor cycles on and off If you select the Sleep Timer in the Smart Saving mode the Smart Saving will be cancelled and the air conditioner will start up in the Sleep Timer mode Solving Common Problems Before contacting the after sales service perform the following simple checks They may save you the time and expense of an unnecessary service call Problem Explanation Solution The air conditioner does not Check that the circuit breaker used for the air conditioner has not operate at all been triggered Check that the power cable is plugged into a wall socket and the socket is switched on if necessary Check that the operating mode indicator COOL or FAN on the unit is lit up if necessary press On Off on the remote control or unit The air conditioner does not Check that there are no obstacles between you and the unit operate with the remote control Replace the remote control batteries if necessary Check that you are close enough to the unit seven metres yards or less No beep is heard when you press Check that you are pointing the remote control at the remote On Off on the remote control control sensor on the unit Replace the remote control batteries if necessary The air conditioner does not cool Check that the correct operating mode has been selected COOL The room temperature may be too low
7. front panel gets broken apply the screw in the hole provided on the front panel Front panel SAMS UN ELECTRONICS Contact SAMSUNG WORLD WIDE If you have any comments or questions regarding a Samsung products contact SAMSUNG customer care center Address 6th floor IFCI Tower Nehru Place New Delhi 110019 Tel 3030 8282 1800 110011 Web Site www samsung com in Printed in India Samsung Electronics Co Ltd All Rights reserved
8. ightly forward below three inches 3 3 Lift the front panel upward Screw Cy Applying excessive force to remove the front panel may cause damage to the tab be sure not to use excessive force 4 Remove two screws on the lower right and left sides of the unit 5 Remove the chassis from the cabinet 6 Remove the rubber cap inserted into the basepan 7 Fix the drain pan as shown in the figure and then connect the drain hose You can use any commercially available drain hose T Rubber cap 8 Install the cabinet at the specified area after installing the drain pan Drain Hose and then re assemble it in the original condition Bottom Side View with gt Secure the front panel to the case by replacing the screw removed in Drain Pan and Hose in Place step 2 If a screw not removed in step 2 secure the panel with a supplied screw 4 In the case of an area where the drain pan can be directly installed on the rear side of the unit after installing the air conditioner 1 Follow steps 6 and 7 only 4 In the case the lock in the
9. irectly from your seat using the remote control Cooling Your Room You must select the Cool mode if you wish to lower the temperature in your e Control Control Panel room You can also set the fan speed 1 If necessary press the On Off button Result The operating mode indicator COOL or FAN on the unit comes on The air conditioner starts up in the mode selected when the unit was last used The unit beeps twice EF The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up automatically after about three minutes 2 If the COOL indicator is not lit up on the unit Press the button on the remote control or Press the MODE button on the unit one or more times until the COOL indicator lights up Result The unit beeps each time you press MODE 4 The air conditioner starts up in Cool mode gt You can change modes at any time 3 To adjust the temperature press the CA or VA button on the remote control one or more times until the required temperature is displayed To adjust the temperature press the A Jor V_ button on the unit one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the temperature buttons The temperature is adjusted by 1 C and displayed on the control pa
10. it one or more times Possible time is between 1 hour and 24 hour inclusive Result 4 The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner switches on automatically when the operating time reaches zero gt You can change the setting mode fan speed and air flow direction after setting the On timer To Cancel the On Timer Timer To cancel the timer press Timer on the remote control or unit one or more times until is displayed or Q 4 on the remote control or unit The air conditioner operates in the mode selected when the unit was last used Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time You can set the period of Remote Control Control Panel time from 1 hour to 24 hours e You can select the Off timer only when the air conditioner is on 1 Check that the air conditioner has been switched on if necessary press the On Off button 9 Power 2 Set the operating time by pressing 4 Timer on the remote control or 4 Timer on the unit one or more times Possible times are between 1 hour and 24 hour inclusive Result The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner switches off automatically when the operating time reaches zero gt You can change the se
11. itioning unit main parts buttons and display Remote control buttons They will help you find the buttons and understand the symbols displayed Inthe main part of the document you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use four different symbols Cz gt IMPORTANT NOTE Moreover applicable wherever the illustrations show the positions of the buttons on both the remote control and the unit itself For the The illustrations have a Remote control Gray background Example Unit itself White background Example Power Inserting the Remote Control Batteries You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly Use two AAA LRO3 1 5 V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities on the battery with on the remote control on the battery with on the remote control 3 Close the cover by sliding it back until it clicks into place Result You can control all the functions on your air conditioning unit d
12. locking objects in front of the unit 8 Ifthe remote control will not be used for a long time remove the batteries 9 Before throwing out the device it is necessary to pull back the battery cells and get rid of them safely CAUTION The manufacturer does not assume responsibility for accidents or injury caused by an incorrectly installed air conditioner If you are unsure about installation contact an installation specialist Contents PREPARING YOUR AIR CONDITIONER m Safety Precautions eee eneren nar ntennnneennnnnnnnnnnnne naene dill 2 m Air Conditioning Unit Main Parts Buttons and Display occccconnncnncconos 4 m Remote Control Buttons cesses 5 m Getting Started eee aaereniiierse ill 6 m Inserting the Remote Control Batteries ooooooccinnicicinnnncinnnccccnnncnconnanccnanencnnons 7 4 OPERATING YOUR AIR CONDITIONER m Cooling Your ROOM ooncccccnnoncccninacanncccnncanrnnncnonannn no norananccnccoran ccoo fill 8 m Airing Your ROOM AAA _ aVV_ 9 m Adjusting the Air Flow Direction Horizontally ooooooccnnnnn cccncinncocncccnnnnnnos 10 m Adjusting the Air Flow Direction Vertically oonnnnninniniinicccororarnarrnnaaanannno 10 4 PROGRAMMING YOUR AIR CONDITIONER m Setting the On Timer erie lV 11 m Setting the Off Timer ernie ll 12 m Setting theBio Sleep Mode eee 13 m Selecting Smart Saving mode occooccccinncccnnonccncon
13. lows Off Timer movement automatically Left amp Right through the air conditioner with Set the Off Timer on V Temp AV the 4 different fan soeeds such as Auto Low Medium High On Timer Off Timer TI On Timer pH Adjust the timer for off timer Increase Decrease the temperature by 1 C Set the On Timer on e Set Bio Ir Bio sleep Adjust the timer for on timer Set the Bio sleep mode on Set Cancel Set Cancel the timer Remote control display Qs pats 7 Operation mode Sua On Timer indicator indicator S DO Bio sleep indicator D q aa Set temperature eae gt a lira ol ti HR 7 Low battery indicator Transmit indicator y SS Fan speed indicator ES i kl Auto all oe Low gt Smart Saver indicator a Sa Medium Air swing indicator Kal High Getting Started You have just purchased a window type room air conditioner and it has been installed by your installation specialist Your Owner s Instructions contain valuable information on using your air conditioner Please take the time to read them as they will help you take full advantage of the unit s functions This Owner s Instructions is just for using your air conditioner correctly Thus the illustrations shown in this manual may not exactly match your air conditioners The booklet is organized as follows The following figures are shown on pages 4 and 5 Air cond
14. nel The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature Timer 4 To set the fan speed to Then High 4 Press the button on the remote control or 0 Press the fs on the unit until the indicator lights up Med Press the button on the remote control or 4 Press the on the unit until the indicator lights up Low Press the button on the remote control or Press the Fensseetjon the unit until the Y indicator lights up Result Each time you press a button the unit beeps 5 To control the direction of the air flow refer to page 10 Airing Your Room If the atmosphere in your room is stale you can air it using the Fan feature and if necessary evacuate the stale air outside 1 If you wish to evacuate stale air outside push the ventilation lever on the front of the unit to the right and the open position lt P Result The air inside the room circulates and stale air is evacuated outside Otherwise push the ventilation lever to the left and the closed position EF Result The air simply circulates inside the room If necessary press the On Off button Result The operating mode indicator COOL or FAN on the unit comes on 4 The air conditioner starts up in the mode selected when the unit was last used 4 The unit beeps twice If the FAN indicator is not lit up on the unit Press the butt
15. on on the remote control or Press the MODE button on the unit one or more times until the FAN indicator lights up Result The unit beeps each time you press MODE The air conditioner starts up in Fan mode gt You can change modes at any time 4 When the air conditioner is in Fan mode the temperature is not displayed in this case you do not need to set the temperature To set the fan speed to Then High 4 Press the button on the remote control or Press the tms i on the unit until the E indicator lights up Med 4 Press the button on the remote control or Press the t on the unit until the indicator lights up Low 4 Press the button on the remote control or Press the tmspueJon the unit until the indicator lights up Result Each time you press a button the unit beeps To control the direction of the air flow refer to page 10 Remote Control Control Panel Power Timer Adjusting the Air Flow Direction Horizontally Remote Control Depending on the position of the unit in your room you can adjust the orientation of the inner air flow blades on the right hand side of the unit thus increasing the efficiency of the air conditioner 1 Press the button on the remote control Result The inner blades swing automatically left and right 2 To stop the blades moving left and right press the button on the remote control gt To
16. oncnnonnnnncnnnnnnconnnnonnnnnnnrannnnnnos 14 RECOMMENDATIONS FOR USE m Operating Recommendation cccccccscccceeseseeeeeeeeeeneeeeesesneeeeeesneeeeeesssneees 15 m Temperature and Humidity Ranges ccccccccccssssesssseesssseeeeeeseeeeneeensnsseanes 15 m Cleaning Your Air Conditioner oooonncccinnnicinnnncconnccccnnnncnnnanaccnrancncanane cananea 16 m Solving Common Problems 00c eee fill 17 m Technical Specifications ccccs 17 INSTALLATION AAA 18 CAUTION The high inrush current of the starting compressor motor can have adverse effects to the operation of other equipment under unfavorable mains conditions This equipment does not comply with the relevant technical standards for the limitation of voltage fluctuations and flicker Before connecting this equipment to the power supply system please report to your supply authority and obtain the consent Do not connect other electric appliances to the same supply lines Air Conditioning Unit Main Parts Buttons and Display The design and shape are subject to change according to the model If a power failure occurs when the air conditioner is operating the unit is switched off Then the power returns the air conditioner starts up again automatically Outer air flow blades up down orientation JIJA III Inner air flow blades right left orientation Air inle
17. st the speed In cool mode Bio Sleep Mode keeps the skin temperature at the best during the 3 stages such as Falling Asleep stage Sound Sleep Stage Wake Up Stage in order Falling Asleep Stage This stage supports enviroment to quickly cool down Together with comfortable intermittent air you will be able to fall asleep quickly 2 Sound Sleep Stage This stage helps users to take deep sleep and keep the healthy skin by controlling wavy temperature control and insensible air stream 3 Wake Up Stage This stage supports comfortable intermittent air to the room to raise human body temperature for refreshing wake up When the set time is over 8 hours this section will be repeated lt i 2 3 A amp A g 7 p mm The above temperature graph might be indicated differently from the temperature indicator of indoor unit depending on the user s lacation gt The recommended temperature is set between 25 C and 27 C and 26 C is the most ideal temperature for comfortable sleep gt Airflow blades left and right swing and fan speed are controlled automatically as the above 3 stages in Bio Sleep Mode gt Set Off timer inBio Sleep Mode over 5 hours You feel disturbed sleep if the Good Morning is set too short or long because the basic off timer is set for 8 hours If the Bio Sleep Mode is set less than 4 hours the operation will be stopped after the set time If the Bio Sleep Mode is set over 5 hours it
18. stop the blades in a specific position and orient the air flow in the corresponding direction simply press the button on the remote control when the blades are in the desired position Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room you can adjust the orientation of the outer air flow blades on the right hand side of the unit RECOMMENDATION When Adjust the blades to face Cooling Upwards Adjust the air flow blades to the desired position by pushing them upwards or downwards gt Ifyou orient the air flow blades downwards and the unit operates in Cool mode for a long period of time dew may 4 Form on the surface of the blades Drip from the blades Setting the On timer The On Timer enables you to switch on the air conditioner automatically after a given period time You can set the period of time from 1 hour to 24 hours You can select the On timer only when the air conditioner is off Remote Control Control Panel 1 Check that the air conditioner has been switched off if necessary press the On Off button 9 Power 2 Set the required mode by pressing the appropriate button 4 or on the remote control Mode button on the unit press it one or more times until the appropriate operating mode indicator lights up Sleep A Fan Speed 3 Set the operating time by pressing Timer on the remote control or 4 Timer on the un
19. t Inside MNI Annn Air filter Inside Air inlet Outside y LAir outlet SS DY Inner air flow blades rightleft orientation Air outlet nedo Outer air flow blades up down orientation Air filter The air filter is located inside Air inlet Outside BLUE BROWN YELLOWGREEN Power cable connection should be committed to Main Power Earth p R Ventilation lever an installation engineer The power plug may be not supplied depending on the model Power cable connection should be committed to Blue Brown Yellow Green 2 installation engineer Main Power Earth Temperature Timer Fan speed settings indicators Operating mode On Off timer setting button Mode selection button Bio Sleep setting button Timer indicator Smart Saver button Remote control signal receiver On Off button Bio Sleep Indicator Fan speed adjustment button Temperatu adjustment buttons Remote Control Buttons and Display Remote Control display 5 Smart Saver Less energy usage makes your Power Q HF M Ee space cool between the temperature Turn on off the air conditioner A Saver range of 26 C 30 C A Mode JA Air swing J Fan speed lt gt Set one of the 5 operating modes Temp Activate Deactivate air flow blade Adjust how much air f
20. tting mode fan speed and air flow direction after setting the Off timer To Cancel the Off Timer To cancel the timer press Timer on the remote control or unit one or more times until is displayed or C on the remote control or unit The air conditioner operates in the mode selected when the unit was last used Timer Timer ved Sleep Fan Speed Selecting Bio Sleep Mode Bio Sleep mode helps users to fall asleep well after going to bed whether Remote Control Control Panel being too hot to sleep or being awakened by coldness The Bio Sleep Mode can be selected only when the air conditioner is switched on or off in cool mode Power gt The BioSleep function can be set whether the air conditioner is switched on or off and this function can be selected for any mode Press the button on the remote control or Press the button on the unit Result Each time you press a butoon the unit beeps The indicator and 4 will be displayed 4 The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time If Bio Sleepis selected after switching on the unit the air conditioner will run in Cool mode During this period the temperature displayed is one you set for the Cool mode If the Bio Sleep is selected before switch on the unit the air conditioner starts running in Cool mode and the temperature is set to 26 C The fan is running in low mode and you can adju
Download Pdf Manuals
Related Search