Samsung RW52EBSS1/XSH User Manual
Contents
1. WWEQLL Pa a a Y 760mm 3 Cleaning the wine chiller Clean the interior and exterior of wine chiller with a warm wet cloth a little of neutral detergent can be added in the warm water 4 Connect the power plug after standing for about one hour Please reference introduction of control panel before you perform the relevant operations the chiller starts running the temperature drops inside and then the wines can be stored after 2 3 hours Installation Guidelines 1 Do not place the wine chiller where the ambient temperature is lower than 10 Cor higher than 32 2 The wine chiller cellar may not start and run at a lower ambient temperature below 10 C if its temperature is set over 10 C 3 When the ambient temperature over 32 C we suggest setting the temperature between 10 C 187C 4 When the ambient temperature below 5 C Please remove the plug from the outlet otherwise the wine may freeze up 08_setting up Operation Instructions for Samsung Wine chiller PREPARATION BEFORE USE Your wine chiller can completely run through the following steps If not please check the power source or try the troubleshooting on the last page of the user manual Please contact the nearest Samsung service center for any doubt or question 1 The proper space shall be reserved between the wall and wine chiller Pl2. Accessories RW52DASS RW52EBSS Description 7 Lock option Reversible option Middle Separator 1 1 Cabinet Upper Shelf 2 2 Accessories Middle Shelf 1 1 Lower Shelf 1 1 Printing j Accessories User Manual l Door Key 1 Accessories Left Hinge Assembly a 1 set K 1 Accessories are in the bag of instruction book 2 Left Hinge Assembly includes left upper hinge 1 left lower hinge 1 left upper hinge cover 1 right screw hole cover 1 operating_13 MAINTENANCE AND CLEANING Internal Shelves Take down all shelves and wipe them with soft cloth dipped with warm water or neutral detergent K a Q After the detergent is used clean them with clear KABA y water and wipe them with dry cloth Door Sealants Please clean the door seals carefully and the grooves shall also be cleaned When installing the door groove after cleaning fix the four corners first and then press them in section by section Middle Separator You may clean the middle separator with a wet rag then polish it with another dry rag But you may not use water to rinse the stains off the middle separator because there are electronic components within it KA As the electronic components such as the conductors S and display panel are included inside the middle separator the user is suggested not to dismantle by himself to avoid Hil any danger ea INFORMATION WHEN CLEANI
3. 7 Memory Function of Power Disconnection e If wine chiller is suddenly disconnected with power during the operation when the power is reconnected wine chiller will work normally at the temperature set by the user before power disconnection INITIAL POWER CONNECTION AND TEMPERATURE ADJUSTMENT Temp Temp Down Up l After wine chiller is connected with power on for the first time all displays will flash 2 seconds It will enter R W operation after 2 seconds 15 C 10 C SAMSUNG e Set the room temperature Normally it can be adjusted according to the actual conditions used by the user 10_operating INTRODUCTION OF CONTROL PANEL RWS52EBSS Temp Temp own Up gt SAMSUNG oa Lock Function Temperature Adjustment LED Lamp Button OINILVdsadO cO Temperature Adjustment The temperature setting range of red wine room is 3 C 18 C Press Temp up button to change the temperature setting of red wine room The set temperature will increase 1 Cby every press It willbe invalid to press Temp up button again when it reaches 18 C The setting sequence is as follows SCOSAC C 60C C 6C 9C 10C a1 1 CS 20 13014015 Ce 1617 0180 Press Temp down Button again within 5 seconds to change room temperature setting The set temperature will decrease 1 Cby every press It will be invalid to press Temp down Again when it reaches 3 C The setting s
4. SAFETY INFORMATION AN e Before operating the wine chiller please read this manual carefully and keep it properly for WARNING your future reference AN Because the following operation instructions cover various models the functions of your WARNING wine Chiller may vary slightly from those described in this manual CAUTION WARNING SIGNS Indicates that a danger of death or serious injury exists WARNING AUTON Indicates that a risk of personal injury or material damage exists OTHER SIGNS Represents something you must NOT do Represents something you must NOT disassemble Represents something you must NOT touch Represents something you must follow Indicates that you must disconnect the power plug from the socket Represents a ground is needed to prevent electric shock St e be a i A It is recommended that this symbol be handled by service man Please follow up specifically as these warning symbols are purposed to prevent you and the others from being injured After reading this section please keep it properly for future reference e This appliance shall be properly installed and located in a proper location in accordance with the manual before it is used Use this appliance for its intended purposes as described in this manual Itis strongly recommended that the repair shall be performed by a qualified man R600a or R134a can be used as a refrigerant Please check th
5. Otherwise there is a risk of electric shock SEVERE WARNING SIGNS AN WARNING Never plug several electrical appliances into one multi functional socket at the same time Otherwise there is a potential risk of fire Prevent the power plug from being very close to the rear of wine chiller to ensure that the power plug will be squashed or damaged the damaged power plug may cause a fire due to its overheating Avoid water tot splash or flow to the wine chiller there is arisk of fire or electric shock Do not put the heavy articles or the electrical heat devices such as a microwave oven on the power cord a there is a risk of short circuit or fire Do not pull out the power socket with wet hands otherwise there is a risk of electric shock Do not put a container filled with water on top of the wine chiller There is a risk of fire or electric shock if any water spills Do not Install a wine chiller in a place where It is wet or may be splashed by water there is a risk of fire or electric shock if the components of the appliances have any insulation problem Do not store any volatile and flammable article in the wine chiller or use it beside the wine chiller Benzene thinner ethanol ether LP gas or other such substances may cause an explosion e Do not disassemble or repair the wine chiller by yourself there is arisk of fire failure and personal injury e Before replacing interior lamp i
6. Model RW52DASS RW52EBSS Imagine the possibilities Thank you for purchasing a Samsung product To receive a more complete service Please register your product at www samsung com global register DA68 01790K 8 FUNCTIONS of Wine Cniller Main functions of Wine chiller Your Samsung wine chiller can save space improve storage and Save energies Digital Type Digitally display and control the working status of wine chiller and the interior temperatures Reliable Performances It has applied with the famous totally enclosed high efficient compressor has excellent performances and high reliability Rational Construction The built in evaporator is used with a high efficiency of Space application The wine chiller is divided into upper and lower rooms and can store red white wine separately Convenient Application The shelves can be pulled outward and pushed inward with application of the guide rails The glass doors are applied so that you can see the status of the inside wine bottles Novelty of Design The glass is reinforced with the ultraviolet resistant films to prevent wine qualities from deterioration LED lamps of low heat radiations are applied to reduce the influences on the wine tastes For easy future reference please write the model and Model serial number down You will find your model number Serial on the right side wall of the wine chiller 02 features Safety information
7. NG THE INTERIOR AND EXTERIOR OF WINE CHILLER e Pull the power plug out of the socket before cleaning The interval between plugging and unplugging shall be more than 5 minutes Prevent water from entering light box while cleaning e Clean with soft towel dipped with warm water or neutral detergent and then wipe with dry cloth Clean the water collection channel and water outlet under cabinet case frequently to ensure that the defrosting water can flow out smoothly Do not clean with the detergent containing any grinding agent e g toothpaste acid substances chemical solvent alcohol or polishing agent Please clean wine chiller periodically to ensure its operational performance iF Please check the following items after maintenance if the power cord has crack or damage if power plug is connected with the socket reliably if the power plug has abnormal heat etc 14 operating DISASSEMBLING SHELVES RW52DASS RW52EBSS You may pull the drawer to the stooper and take it out tipsily Do not pull out by force during the disassembly to avoid damaging the wine chiller LAYOUT OF LOADING WINE BOTTLES RWS52DASS RW52EBSS ONILVdsd0O dO T E R EN ARANAN ee z AaBASASAa MANANA CoCo aQanao ce 000 OHOHOHOLMO en LO OOo 14 14 r 52 30 77 750ml Operating_15 METHOD OF REPLACING LEFT AND RIGH
8. T DOORS CRW52DASS RW52EBSS lt a CAPHINGEHOLER CAP DOOR COVER HINGE L lt 9 gt y GROMMET HINGE UPP WASHERC i GROMMET HINGE LOW STOPPER DOOR og SPACER gt LEG S HINGE LOW L 7 aS 7 P HINGE LOW R am LEG 1 Unplug the wine chiller 2 In the bottom of the front hinge cover use a flat head screw driver or equivalent tool to insert in the gap between the HINGE UPP R and COVER HINGE R and turn the screw driver outwards by force to take down the COVER HINGE R and put it aside 3 Remove the four screws in the HINGE UPP R and take down it and the WASHER A under it 4 lake down the door and put it on the protected flat surface 5 Take down the CAP HINGE HOLE L on the left of the cabinet 6 Remove the screws that fix the STOPPER DOOR to take down it and WASHER C Then use a tool to take down the GROMMET HINGE LOW 7 Use a tool to take down the GROMMET HINGE UPP on the upper part of the door Install it to the shaft hole at the bottom of the door 8 Install the GROMMET HINGE LOW STOPPER DOOR and WASHER C to the shaft hole at the top of the door by installing the screws in the contrary sequence 9 Slope the wine chiller gently at an angle of less than 45 degree 10 Dismantle the bottom LEG at right side and the screws that fix the HINGE LOW R Take down the HINGE LOW R and the WASHER B on it Keep the HINGE LOW R for future use 11 Ta
9. all be fully refrigerated at the initial power connection before the wines are stored and the wine bottles shall not be put around the temperature sensor to avoid influencing the display of the correct temperature e Do not put the wine chiller upside down or horizontally The sloping angle between the body and the ground shall exceed 45 when sloping is required to prevent the compressor oil from entering the system pipe and affecting the refrigerating efficiency e Do not allow the children to play or climb up the wine chiller to avoid damaging the wine chiller or injuring the children After the power is disconnected it can be reconnected only after waiting for 5 minutes to avoid damaging the compressor e The appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and Knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety e Do not store pharmaceuticals products scientific materials or temperature sensitive products in the refrigerator Products that require strict temperature controls must not be stored in the refrigerator The refrigeration of the wine chiller relies on the refrigerant which is filled into the wine chiller by aspecial manufacturing process Therefore the pipe on the rear of the wine chiller shall be ensured intact e If any abnormal so
10. ck the size of your door to confirm if the wine chiller can pass through your door x SIZE OF THIS APPLIANCE size mm model Width 595 RW52DASS RW52EBSS Depth 665 RW52DASS RW52EBSS Height 840 RW52DASS RW52EBSS Dismantle all packaging components including the interior tapes etc Please remove the foam pad under the wine chiller during the use 1 The floor on which the wine chiller is located shall be flat and solid otherwise the interior refrigerating system may not work properly If itis not slightly flat adjust the levelness of the wine chiller by turning the adjustment leg on the bottom of the cabinet raised counterclockwise The noises will be increased if it is put on the unsolidified floor Please underlay a solid wood pad when it is put on the carpet in case that the heat on the bottom of wine chiller causes discoloration or blocks heat radiation setting up_07 dN ONILLAS LO INSTALLING YOUR WINE CHILLER 2 Enough space shall be reserved for wine chiller The minimum distance between the rear wall or side wall of wine chiller and the wall shall not be less than 55mm The height above the top shall not be less than 100mm Not less than55mm Not less than1OOQmm nEn I Not less than55mm 1 Not less than55mm S ee I I I I
11. e chiller is running It will disappear automatically after shutdown Wine bottles shall not be closely against the back wall of wine chiller There is frost on the back wall of the cabinet Heat radiation devices condensators are Both sides heat and The front cabinet frame or nstaled onr bolhsidesotwmnechiller side wall of wine chiller heats nae there is abnormal smell Heating is anormal phenomenon EA Wine chiller lowers down its interior temperature through the operation of compressor gt and circulation of the refrigerant etc to ensure the freshness and nutrition of the foods in wine cellar You may hear some light sounds and it is normal Please take easy to use it Troubleshooting_17 English Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office fo
12. e compressor label on the rear of this appliance or the wiring diagram on the back of the cabinet and confirm the refrigerant applied by this wine chiller e The refrigerant R600a is a natural gas that can be used in various kinds of AN environments But as it is flammable during the transportation and installation of this appliance attention shall be paid not to damage any component in the cooling loop The refrigerant leaked from the piping can be ignited or injure the eyes If any leakage is discovered the open fire or potential fire sources must be prohibited and the room where this appliance is located shall be ventilated for several minutes Safety information 03 Safety information AN e o avoid the generation of a flammable gas mixed by the air and the refrigerant leaked from WARNING the refrigerating circuit the size of the room where this appliance is located shall depends on the applied quantity of the refrigerant e Never start up an appliance showing any sign of damage Please consult your dealer if there is any doubt e The room size is required to be 1m every 8 grams of ROOa refrigerant inside the appliance e The quantity of the refrigerant is shown on the wiring diagram on the back side of your wine chiller e Please dispose of the packaging materials for this product in an environment friendly manner e Pull the power plug out of the socket before replacing the interior light of the wine chiller
13. ease refer to 2 Please check if the screen displays the temperature when the wine chiller is energized 3 Set the temperature control to the minimum and wait for 1 hour Then the wine chiller 4 It takes some time for wine chiller to reach the proper temperature after it starts up the installation instruction in this manual shall be slightly cooled down and the motor runs stably OINILVdsadO cO You can store the wines inside once the temperature of wine chiller is sufficiently low This appliance is intended to be used exclusively for the storage of wine INTRODUCTION OF CONTROL PANEL RW52DASS 1 Child Lock Indicator LED Lamp Button Temperature of Lower Room SAMSUNG ono oN p aig Down Up Room Selection Butto Temperature Adjustment Temperature of Upper Room Room Selection Function Select upper room and lower room by pressing Custom button Press Custom button for the first time and the temperature display of upper room on the panel will flash to enter the temperature setting status of upper room Press Custom again and the temperature displays of upper and lower rooms on the panel will flash to enter the temperature setting status of lower room 2 lTemperature Adjustment of Upper Room The temperature setting range of upper room is 8 C 18 and can be set by the temperature setting button Press Custom to enter the temperature setting stat
14. equence is as follows 18017 C 16C 15C 14013012011 C 10 9C 5C 7C 6C 5 40C 8C The displayed set temperature starts to flash in a cycle of 1 second 0 5s on 0 5s off when pressing Temp down Button or Temp up button at the first time The flash will stop if there is no press on Temp down button or Temp up button within 5 seconds and the current temperature will be displayed When the set temperature is below and equal to 12 C W indicator of white wine room is on and R indicator of red wine room is off When the set temperature is above and equal to 13 C R indicator of red wine room is on and W indicator of white wine Is off 2 Child Lock Function e Inthe non button lock mode press Lock button for 3 seconds and Lock indicator on the panel will be on to select the button lock function e In the button lock mode press Lock button for 3 seconds and Lock indicator on the panel will be off to exit from the button lock mode In the button lock mode the temperature adjustment button does not work while the light button works as usual 3 Failure Warning Function e Please remove the plug from the outlet and stop using the wine chiller when the wine chiller has the following phehomena The room temperature flasher as H it indicates the temperature of the environment is too low Please inform the professional personnel for repair immediately when wine chiller has the following phehomena The room
15. ion No refrigeration not cold too cold Ambient temperature is quite high in summer Wine chiller has been The door is opened and closed frequently running for along time The exterior ventilation of wine chiller is not good If wine chiller is not level slightly its running Wine chiller is not sound will be increased Adjust the levelness positioned level of wine chiller by turning the adjustment leg under the cabinet The temperature in wine chiller can drop down quickly through the circulation of the refrigerant Air or water flowing sound inthe pipeline The refrigerant has two types gas and liquid which may generate the light Wine chiller has sounds during the circulation abnormal sounds _ Compressor is running The sound is alittle bit high when it starts up The sound of high efficient wine chiller is higher as its compressor is more powerful Light buzzing sounds The electrical components such as main control panel starter relay heat protector Clattering ooh sound and solenoid valve etc give off the clattering and boh sound due to their constant connection or disconnection Door door frame and cabinet t occurs when ambient humidity is high frame have condensates Wipe with soft cloth Defrosting water Condensates water overflows in the chiller leakage frosting icing The water outlet is blocked t is anormal condition when win
16. ke down the bottom LEG and SPACER on the other side and install them in the right side IMPORTANT The left LEG has a SPACER that must be moved to the right side when the door is reversed 12 Fix the HINGE LOW L supplied with the instruction book in the left side with the screws and install the bottom LEG Put the WASHER B in the hinge shaft 13 Put the wine chiller upright 14 Put the door on the wine chiller after rotating the door to 180 The shaft hole of the door shall align with the hinge shaft and the door is closely against the lower hinge 15 Insert the HINGE UPP L supplied with the instruction book into the hinge hole on the left side of the door and fix the HINGE UPP L to the wine chiller cabinet with screws Be Sure to place the WASHER A under the HINGE UPP L And make sure that the door is aligned with the wine chiller cabinet before fastening the screws 16 Qpen and close the door checking the alignment of the door to the cabinet If necessary loosen the screws attaching the HINGE UPP L to the cabinet realign the door and retighten the screws 17 Fix the COVER HINGE L and CAP HINGE HOLE Lsupplied together with the instruction book and connect the power Reset the temperatures of wine chiller 16_operating fOUDIESNOOTING The plug is not connected properly Power is not connected Wine chiller does not work l Wine cellar is reconnected with power less than 5 minutes after it is disconnected with power during the operat
17. lows It will restore to the status before entering the temperature setting if there is no press on Temp down button within 5 seconds When the set temperature of lower room is below 13 C W indicator of lower room will be on and R indicator will be off 4 Child Lock Function e Inthe non button lock mode press Temp down buttonand Temp up button together for 3 seconds and Lock indicator on the panel will be on and the button lock function is started up Press these two buttons together again for 3 seconds to cancel this function e Inthe button lock mode the temperature adjustment button does not work while the light button works as usual 5 Failure Warning Function e Please remove the plug from the outlet and stop using the wine chiller when the wine chiller has the following phehomena The room temperature flasher as H it indicates the temperature of the environment is too low Please inform the professional personnel for repair immediately when wine chiller has the following phehomena The room temperature flashes as E1 E2 E3 E4 R R d dd 6 LED Control Function e When interior light is off interior LED light will be on immediately after pressing Lighting On Off button When interior LED lights over 1 hour it will go out automatically If interior LED light is on it will be off immediately after pressing Lighting On Off button
18. n the wine chiller please unplug the socket otherwise there is a risk of electric shock e Ifyou are going to dispose of the wine chiller please dismantle its doors and sealants before throwing the wine chiller away it can avoid locking the children in the wine chiller in this way in case of power consumption or electric shock due to electric leakage of the wine chiller a E e Wine chiller must be grounded Never use a gas pipe telephone line or other potential lightning conductor as an grounding point the improper application of the grounding plug may cause electric shock 04_Safety information Safety information CAUTION SIGNS AN Aloose power plug shall not be inserted into the power socket CAUTION CAUTION A WARNING there is a risk of electric shock or fire e Never drag the power cord to disconnect it the damaged power cord may cause short circuit fire or electric shock if the power cord is damaged it must be replaced by the manufacturer an approved service dealer or qualified service person e Never put any article on top of wine chiller The article may fall down to cause person injury or material damage when opening or closing the door of wine chiller e Never store any medicine scientific material or other temperature sensitive product in wine chiller check the identification labels of the products to ensure that they can be refrigerated e The wine chiller sh
19. perating 09 3 Temperature Adjustment of Lower Room The temperature setting range of lower room is 3 C 18 C and can be set by the temperature setting button Continuously press Custom twice to enter the temperature setting status of lower room and the lower room displays the set temperature Press Temp up button again within 5 seconds to change the temperature setting of lower room The set temperature will increase 1 C by every press and it will be invalid to press Temp up button again when it reaches 18 C The setting sequence is as follows SCAG 506 CeCe 0 CHK oC SH 0 Ca 11 C 1276 18 0 140 a 19 16 CH 17 ee 16 When the set temperature of lower room is above and equal to the current setting of upper room the set temperature of upper room will increase together with that of lower room synchronously When the set temperature of lower room is above 13 C R indicator of lower room will be on and W indicator will be off It will restore to the status before entering the temperature setting if there is no press on Temp up button within 5 seconds 1SC S17 CH 16 C156 CH 14016 C e120 11 CH 10 9 C 80 0 0C 5 40 3CT In the temperature setting status of lower room press Temp down button again within 5 seconds to change the temperature setting of lower room The temperature will decrease 1 C by every press and it will be invalid to press Temp down button again when it reaches 3 C The setting sequence is as fol
20. r details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Memo Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care centre Country Area Customer Care Center amp www samsung com hk Chinese HONG KONG 852 3698 4698 dre on S Ein
21. temperature flashes as 1E E R R 4 LED Control Function e When interior light is off interior LED light will be on immediately after pressing Lighting On Off button When interior LED lights over 1hour it will go out automatically e If interior LED light is on it will be off immediately after pressing Lighting On Off button 5 Memory Function of Power Disconnection e If wine chiller is suddenly disconnected with power during the operation when the power is reconnected wine chiller will work normally at the temperature set by the user before power disconnection Operating_11 INITIAL POWER CONNECTION AND TEMPERATURE ADJUSTMENT Lock SA M S U N G eon Hold 3 sec eth Temp 0 OE BY e am Nar CSA After wine chiller is power on for the first time all displays will flash 2 seconds It starts normal running after 2 seconds R indicator of red wine room is on and the set temperature of red wine is displayed as 15 C e Set the room temperature Normally it can be adjusted according to the actual conditions used by the user 12 operating SCHEMATIC DIAGRAM OF WINE CHILLER TAKE RW52EBSS SERIES AS AN EXAMPLE N Upper Shelf Middle Separator oohoo N dad Middle Shelf R gt Lower Shelf RK There are two options ofthe door 1 lock option 2 reversible option
22. und smell or smoke is observed unplug the power plug immediately and contact the nearest Samsung electronic service center e When cleaning the plug do not remove foreign matters from the pins of the power plug with wet cloth there is a risk of burn and fire Y e Do not stretch the hands under the bottom of the wine chiller sharp edges may cause personal injury e Pull out the power plug if the wine chiller will not be used for along period of time the insulation aging may cause a fire e Keep air vent and air channel in the wine chiller clean and avoid being blocked Do not use any mechanical equipment or other method to accelerate the defrosting process except the methods recommended by the manufacturer e Do not damage the refrigerating system and circuit Do not use any other electronic product in the wine chiller except the electronic products recommended by the manufacturer Safety information_05 Contents ASSEMBLE YOUR WINE CHILLER 9 OPERATION INSTRUCTION FOR 09 WINE CHILLER o 13 14 15 15 16 TROUBLESHOOTING Installing your wine chiller Preparations before use Control Panel Initial power connection and temperature adjustment Schematic diagram of wine chiller Maintenance and cleaning Dismantle the shelves layout of Loading wine bottles Changing the opening directions of the doors Setting up your wine cniller INSTALLING YOUR WINE CHILLER CHECK THE SIZE OF YOUR DOOR Che
23. us of upper room and the upper room displays the set temperature Press Temp up button again within 5 seconds to change the temperature setting of upper room The set temperature will increase 1 C by every press and it will be invalid to press Temp up button again when it reaches 18 C The setting sequence is as follows SC OC 0C HK 11 C12 eC Kio Ca 14 CH a CH 16 17 Ce 108 When the set temperature of upper room is above and equal to 13 C R indicator of upper room will be on and W indicator will be off It will restore to the status before entering the temperature setting if there is no press on Temp up button within 5 seconds In the temperature setting status of upper room press Temp down button again within 5 seconds to change the temperature setting of upper room The temperature will decrease 1 C by every press and it will be invalid to press Temp down button again when it reaches 8 C The setting sequence is as follows ICC CFC e C14 CS 13 Ce I2ZC 11 CK 10 Cae Cae When the set temperature of upper room is below and equal to the current setting of lower room the set temperature of lower room will decrease together with that of upper room synchronously When the set temperature of upper room is below 13 C W indicator of upper room will be on and R indicator will be off It will restore to the status before entering the temperature setting if there is no press on Temp down button within 5 seconds o
Download Pdf Manuals
Related Search