Home
Samsung S24B240BL 用户手册
Contents
1. e These are general instructions For exact instructions see the User Manual supplied with the locking device e You can purchase the locking device from an electronics store an online shop or our service center Installing the Product 2 4 3 Using the product 3 1 Standard Signal Mode Table This product delivers the best picture quality when viewed under the optimal resolution setting The optimal resolution is dependent on the screen size Therefore the visual quality will be degraded if the optimal resolution is not set for the panel size It is recommended setting the resolution to the optimal resolution of the product If the signal from the PC is one of the following standard signal modes the screen is set automatically However if the signal from the PC is not one of the following signal modes a blank screen may be displayed or only the Power LED may be turned on Therefore configure it as follows referring to the User Manual of the graphics card For the optimal resolution refer to the Specifications 24B240BL S24B240KL DISPLAY MODE es an ABE PIXEL CLOCK MHZ Sino e Nas IBM 720 X 400 31 469 70 087 28 322 MAC 640 x 480 35 000 66 667 30 240 MAC 832 x 624 49 726 74 551 57 284 MAC 1152 x 870 68 681 75 062 100 000 VESA 640 x 480 31 469 59 940 25 175 VESA 640 x 480 37 861 72 809 31 500 VESA 640 x 480 3
2. Avoid installing the product in a location exposed to direct sunlight and installing the product near a heat source such as a fire or heater e This may shorten the product life cycle or cause fire Edible oil such as soybean oil can damage or deform the product Do not install the product in a kitchen or near a kitchen coun ter Do not place the product face down on the floor e This may damage the panel of the product When putting the product down handle it gently e Otherwise it may result in a problem with the product or injury 1 4 Major Safety Precautions Usage Related A Warning Since a high voltage runs through the prod uct never disassemble repair or modify the product yourself e Otherwise it may result in fire or electric shock e Ifthe product needs to be fixed contact a service center If the product generates a strange noise a burning smell or smoke unplug the power plug immediately and contact a service cen ter e Otherwise it may result in electric shock or fire If you drop the product or the case is dam aged turn the power off and unplug the power cord Contact a service center e Otherwise it may result in fire or electric shock During a lightning or thunderstorm power off the product and remove the power cable e Otherwise it may result in electric shock or fire Do not move the product by pulling the power cord or any cable e Otherwise
3. Min GREECE 80111 SAMSUNG 80111 726 http www samsung com 7864 only from land line 30 210 6897691 from mobile and land line HUNGARY 06 80 SAMSUNG 726 7864 http www samsung com ITALIA 800 SAMSUNG 726 7864 http www samsung com More Information 5 3 EUROPE LATVIA 8000 7267 http www samsung com LITHUANIA 8 800 77777 http www samsung com LUXEMBURG 261 03 710 http www samsung com MONTENEGRO 020 405 888 http www samsung com NETHERLANDS 0900 SAMSUNG http www samsung com 0900 7267864 0 10 Min NORWAY 815 56480 http www samsung com POLAND 0 801 1SAMSUNG 172 678 http www samsung com 48 22 607 93 33 PORTUGAL 808 20 SAMSUNG 808 20 7267 http www samsung com RUMANIA 08008 SAMSUNG 08008 726 7864 http www samsung com TOLL FREE No SERBIA 0700 Samsung 0700 726 7864 http www samsung com SLOVAKIA 0800 SAMSUNG 0800 726 786 http www samsung com SPAIN 902 1 SAMSUNG 902 172 678 http www samsung com SWEDEN 0771 726 7864 SAMSUNG http www samsung com SWITZERLAND 0848 SAMSUNG http www samsung com ch 7267864 CHF 0 08 min NESUUED http www samsung com ch fr French U K 0330 SAMSUNG 7267864 http www samsung com CIS ARMENIA 0 800 05 555 http www samsung com AZERBAIJAN 088 55 55 555 http www samsung com BELARUS 810 800 500 55 500 http www samsung com GEORGIA 0 800 555 55
4. Optimum Mode 3 4 Using the product 4 Troubleshooting 4 1 Monitor Self Diagnosis e You can check if the product is working properly using the Self Diagnosis function e Ifa blank screen is displayed and the Power LED blinks even if the product and the PC are properly connected perform the self diagnosis function according to the procedures below Turn the product and the PC off Separate the signal cable from the product Turn the product on a SP NL If the product is working properly the lt Check Signal Cable gt message appears In this case if a blank screen is displayed again make sure that there is no problem with the PC and the connection The product is working properly Troubleshooting 4 1 4 2 Before Requesting Service Please check the following before requesting After Sales service If the problem continues please contact your nearest Samsung Electronics Service Center A BLANK SCREEN APPEARS CANNOT TURN THE PRODUCT ON Is the power cord connected properly Check the connection status of the power cord Is the lt Check Signal Cable gt message displayed on the screen Connected using the D sub cable Check the cable connecting the PC and the product Connected using the DVI cable When cables are connected correctly and the monitor dis plays this message press MENU button to display OSD then press 37 and MENU buttons to
5. it may result in electric shock e Otherwise it may result in fire due to or fire O overheating of the wall outlet Avoid plugging in or unplugging the power Plug the power plug in firmly Srp ey Wer anaes an e Otherwise it may result in fire e Otherwise it may result in electric nk shock db Make sure to connect the power cord to a Avoid bending or twisting the power cord grounded wall outlet for insulation class 1 excessively and avoid placing heavy objects equipment only Is on the cord of e Otherwise it may result in electric shock e Otherwise it may result in electric shock or injury or fire due to a damaged power cord Keep the power cord and the product away from a heater p e Otherwise it may result in electric shock D or fire LI If the pins of the power plug or the wall out let are covered in dust clean it using a dry cloth e Otherwise it may result in fire 1 4 Major Safety Precautions A Caution Avoid unplugging the power plug while the product is operating e Otherwise it may damage the product due to electric shock When unplugging the power plug from the wall outlet make sure to hold it by the plug and not by the cord e Otherwise it may result in electric shock or fire Installation Related A Warning AVOID PLACING BURNING CANDLES ab MOSQUITO REPELLENT OR CIGA RETTES ON THE PRODUCT AND _ INSTALLING THE PRODUCT NEAR A HEATER e Otherwise
6. it may result in fire Avoid installing the product in a badly venti lated location such as inside a bookshelf or 1 EZA closet SH LL e Otherwise it may result in fire due to internal over heating Keep the plastic bags used to pack the product away from children e If children place the plastic bags over their heads they may suffocate Make sure to use only the power cord sup plied by our company In addition do not use the power cord of another electric appli ance e Otherwise it may result in electric shock or fire Connect the power plug to a wall outlet that can be easily reached e When a problem occurs with the product you must unplug the power plug to cut the power off completely You cannot cut the power off completely using only the power button on the product Ask an installation engineer or relevant company to install the product onto the wall e Otherwise it may result in injury e Make sure to use the specified wall mount Keep a distance of at least 10 cm from the wall when installing the product for ventila tion e Otherwise it may result in fire due to internal over heating Avoid installing the product in a location that is unstable or exposed to excessive vibra tions such as on an unstable or slanted shelf e The product may fall and this may result in damage to the product or injury e If you use the product in a location exposed to excessive vibrati
7. 24B240BL S24B240KL S27B240B S27B240K Monitor User Manual The color and the appearance may differ depending on the product and the specifications are subject to change without prior notice to improve the performance ifs Table Of Contents MAJOR SAFETY PRECAUTIONS Before Y u Stari naa ape ec KABANATA niina iere iaaa Custody and Maintenance 00 an Cleaning the Monitor 020 eee eee eee Safety Precautions XX sa nman ka eee wediaw chew es weet INSTALLING THE PRODUCT Package Contents 002 c cece eee ee Installing the Stand 4 Connecting the monitor 0 00 eee eee Kensington LOCK aa Hed saia Ka AG MR che AL a eet USING THE PRODUCT Standard Signal Mode Table 0 00 cece e eee eee Installing the Device Driver 0000 eee eee Product Operating Buttons 0 0 0 ee Using the Screen Adjustment Menu OSD On Screen Display TROUBLESHOOTING Monitor Self Diagnosis 2c cece eee Before Requesting Service 0 20 c cece es ENG eee een Be eee ee ees bee ee oe eee ee ee eee MORE INFORMATION Specifications AA AA Power Saving Function 000 aan Contact SAMSUNG WORLD WIDE 00 cece eee eee Responsibility for the Pay Service Cost to Customers Correct Disposal of This Product Waste Electrical 4 Electronic Equipment 1 Major Safety Precautions 1 1 Before Yo
8. in a problem with the product or injury e If the product is tilted excessively the product may fall and this may result in injury Maintaining the Correct Posture when Using this Product Maintain the correct posture when using this product e Straighten your back e Keep a distance of 45 50 cm from your eyes to the screen Look down at the screen and face the screen forwards e Adjust the angle of the product so that light is not reflected onto the screen e Keep your elbow at a right angle and keep your arm level with the back of your hand e Keep your elbow at a right angle e Place your heels flat on the ground while keeping your knees at an angle of 90 degrees or higher and maintain the position of your arm so that your arm is below your heart Major Safety Precautions 1 4 2 Installing the Product 2 1 Package Contents e Unpack the product and check if all of the following contents have been included e Store the packaging box in case you need to move the Product at a later stage Monitor CONTENTS lt ul Quick Setup Guide Warranty Card User Manual Not available in all locations DC Adapter Power Cord Stand Stand Connector OPTION 4 D Sub Cable DVI Cable headphone holder SCrews The cables provided may vary depending on the product you purchase 2 1 Installing the Product 2 2 Installing the Stand
9. the power cable may be damaged and product failure an electric shock or fire may result Avoid lifting up or move the product by hold ing only the power cord or signal cable e Otherwise it may result in electric shock fire or a problem with the product due to damage to the cable Before moving the product turn off the power switch and disconnect the power cable and all other connected cables e Otherwise the power cord may be damaged and a fire or electric shock may result Avoid letting children to hang or climb onto the product e Otherwise it may result in the product falling and this may result in injury or death Avoid placing objects such as toys and cookies on top of the product e Ifa child hangs over the product to grab an object the object or the product may fall and this may result in injury or even death Avoid dropping an object over the product or cause impact to the product e Otherwise it may result in electric shock or fire When a gas leak occurs do not touch the product or the power plug and ventilate immediately e A spark may result in an explosion or fire Avoid using or placing inflammable spray or objects near the product e This may result in an explosion or fire Major Safety Precautions Take care not to block the vent by a table cloth or curtain e Otherwise it may result in fire due to internal overheating Avoid placing a liquid co
10. water or cleaning agent directly onto the monitor Otherwise the liquid may sink into the monitor and cause a fire electric shock or failure 4 Clean the exterior of the monitor using a soft cloth dampened with a small amount of water 5 Connect the power cable to the monitor after you have finished cleaning 6 Power on the monitor and PC Precautions for Storage e Using an ultrasonic humidifier may cause white stains on a highly glossy product Be sure you contact the nearest service center paid service for cleaning the inside of the monitor Major Safety Precautions 1 3 1 4 Safety Precautions Icons used for safety precautions ICON NAME MEANING Warin Failing to follow the precautions marked with this sign may result in a serious injury or A g even a fatality Caution Failing to follow the precautions marked with this sign may result in a personal injury or A property damage Meaning of Signs S Do not perform Q Q Do not disassemble Q Do not touch B Must be followed The power plug must be unplugged from the wall outlet Must be grounded to prevent electric shock Power Related The product image used in the following pictures for your reference may look different from the actual product A Warning Avoid using a damaged power cord or plug Avoid connecting multiple electric appli or a loose power outlet ances to a single wall outlet e Otherwise
11. 5 http www samsung com KAZAKHSTAN 8 10 800 500 55 500 http www samsung com GSM 7799 KYRGYZSTAN 00 800 500 55 500 http www samsung com MOLDOVA 0 800 614 40 http www samsung com MONGOLIA 7 800 555 55 55 http www samsung com RUSSIA 8 800 555 55 55 http www samsung com TADJIKISTAN 8 10 800 500 55 500 http www samsung com UKRAINE 0 800 502 000 http www samsung com ua Ukrainian http www samsung com ua ru Russian UZBEKISTAN 8 10 800 500 55 500 http www samsung com 5 3 More Information ASIA PACIFIC AUSTRALIA 1300 362 603 http www samsung com CHINA 400 810 5858 http www samsung com HONG KONG 852 3698 4698 http www samsung com hk Chinese http www samsung com hk en English INDIA 1800 1100 11 http www samsung com 3030 8282 1800 3000 8282 1800 266 8282 INDONESIA 0800 112 8888 http www samsung com 021 5699 7777 JAPAN 0120 327 527 http www samsung com MALAYSIA 1800 88 9999 http www samsung com NEW ZEALAND 0800 SAMSUNG 0800 726 786 http www samsung com PHILIPPINES 1 800 10 SAMSUNG 726 7864 http www samsung com for PLDT 1 800 3 SAMSUNG 726 7864 for Digitel 1 800 8 SAMSUNG 726 7864 for Globe 02 5805777 SINGAPORE 1800 SAMSUNG 726 7864 http www samsung com TAIWAN 0800 329 999 http www samsung com 0266 026 066 THAILAND 1800 29 3232 http www samsung com 02 689 3232 VIETNAM 1 800 588 889 http ww
12. 7 500 75 000 31 500 VESA 800 x 600 35 156 96 250 36 000 VESA 800 x 600 37 879 60 317 40 000 VESA 800 x 600 48 077 72 188 50 000 VESA 800 x 600 46 875 75 000 49 500 VESA 1024 x 768 48 363 60 004 65 000 VESA 1024 x 768 56 476 70 069 75 000 VESA 1024 x 768 60 023 75 029 78 750 VESA 1152 x 864 67 500 75 000 108 000 VESA 1280 x 720 45 000 60 000 74 250 VESA 1280 x 800 49 702 59 810 83 500 VESA 1280 x 1024 63 981 60 020 108 000 HF VESA 1280 x 1024 79 976 75 025 135 000 t VESA 1440 x 900 55 935 59 887 106 500 VESA 1440 x 900 70 635 74 984 136 750 VESA 1680 x 1050 65 290 59 954 146 250 VESA 1920 x 1080 67 500 60 000 148 500 HF 3 1 Using the product 27B240B S27B240K HORIZONTAL VERTICAL SYNC POLARITY H DISPLAY MODE FREQUENCY KHZ FREQUENCY HZ PIXEL CLOCK MHZ V IBM 720 X 400 31 469 70 087 28 322 MAC 640 x 480 35 000 66 667 30 240 MAC 832 x 624 49 726 74 551 57 284 MAC 1152 x 870 68 681 75 062 100 000 VESA 640 x 480 31 469 59 940 25 175 VESA 640 x 480 37 861 72 809 31 500 VESA 640 x 480 37 500 75 000 31 500 VESA 800 x 600 35 156 96 250 36 000 VESA 800 x 600 37 879 60 317 40 000 VESA 800 x 600 48 077 72 188 50 000 VESA 800 x 600 46 875 75 000 49 500 VESA 1024 x 768 48 363 60 004 65 000 VESA 1024 x 768 56 476 70 06
13. 9 75 000 VESA 1024 x 768 60 023 75 029 78 750 VESA 1152 x 864 67 500 75 000 108 000 tF VESA 1280 x 720 45 000 60 000 74 250 VESA 1280 x 800 49 702 59 810 83 500 VESA 1280 x 1024 63 981 60 020 108 000 VESA 1280 x 1024 79 976 75 025 135 000 VESA 1440 x 900 55 935 59 887 106 500 VESA 1440 x 900 70 635 74 984 136 750 VESA 1680 x 1050 65 290 59 954 146 250 VESA 1920 x 1080 67 500 60 000 148 500 Horizontal Frequency The time taken to scan one line from the left most position to the right most position on the screen is called the horizontal cycle and the reciprocal of the horizontal cycle is called the horizontal frequency The horizontal frequency is represented in kHz Vertical Frequency A panel must display the same picture on the screen tens of times every second so that humans can see the picture This frequency is called the vertical frequency The vertical frequency is represented in Hz Using the product 3 1 3 2 Installing the Device Driver If the device driver is installed you can set the resolution and frequency to the optimal configuration for the product The device driver is included on the CD ROM supplied with the product If the supplied drive file is corrupted please visit a service center or Samsung Electronics website http www samsung com and download the driver Insert the driver installation CD ROM into the CD ROM drive Click on Windows Driver
14. A 00 1800 5077267 http www samsung com latin Spanish http Awww samsung com latin_en English PANAMA 800 7267 http www samsung com latin Spanish http Awww samsung com latin_en English PERU 0 800 77 7 08 http www samsung com PUERTO RICO 1 800 682 3180 http www samsung com TRINIDAD 8 TOBAGO 1 800 SAMSUNG 726 7864 http www samsung com VENEZUELA 0 800 100 5303 http www samsung com EUROPE AUSTRIA 0810 SAMSUNG http www samsung com 7267864 E 0 07 min BELGIUM 02 201 24 18 http www samsung com be Dutch http www samsung comibe fr French BOSNIA 05 133 1999 http www samsung com BULGARIA 07001 33 11 normal tariff http www samsung com CROATIA 062 SAMSUNG 062 726 7864 http www samsung com CYPRUS 8009 4000 only from landline http www samsung com 30 210 6897691 from mobile and land line CZECH 800 SAMSUNG 800 726786 http www samsung com Samsung Electronics Czech and Slovak s r o Oasis Florenc Sokolovska 394 17 180 00 Praha 8 DENMARK 70 70 19 70 http www samsung com EIRE 0818 717100 http www samsung com ESTONIA 800 7267 http www samsung com FINLAND 09 85635050 http www samsung com FRANCE 01 48 63 00 00 http www samsung com GERMANY 0180 5 SAMSUNG bzw http www samsung com 0180 5 7267864 0 14 Min aus dem dt Festnetz aus dem Mobilfunk max 0 42
15. Before assembling the product put the product down on a flat and stable surface table etc with the screen facing down Lay a soft blanket on the table for protection Next place the product with the screen fac eh ing down onto the blanket Insert the Stand Connector into the Stand in the direction shown by the figure Install the Stand Connector into the Stand by rotating as shown in the figure Check if the Stand Connector is firmly connected Installing the Product 2 2 Turn the connecting screw at the bottom of the stand fully so that it is completely fixed Put the headphone holder in the place shown by figure and then turn the connecting screws fully so that it is completely fixed Hold the main body of the product with your hand as shown by the figure Push the assembled stand into the main body in the direction of the arrow as shown in the figure tiit Caution Never lift the product by holding only the stand More force may be required to detach the stand from the product than when it was attached 2 2 Installing the Product 2 3 Connecting the monitor Connecting with a PC e The connecting part may differ depending on the product model e Do not connect the power cable until all connections are completed e Connect the product to a PC depending on the video output supported by the PC e When the graphics card provides D Sub lt Analog gt output e Connect the RGB IN port of t
16. Complete the remaining installation steps according to the instructions displayed on the screen PP NY Select the model of your product from the model list T SAMSUNG monitor betel her Select the display adapter on which you wert to iniall he monilor Sigla the montar aich you wel bo inatali 5 Check if the appropriate resolution and screen refresh rate are displayed in the Control Panel settings For more information refer to the document about the Windows operating system 3 2 Using the product 3 3 Product Operating Buttons Product Operating Buttons ICON DESCRIPTION MENU 1 Press this button to display the On Screen Display OSD 2 When in the menu press this button to move down to the option below or adjust values in the OSD OSD Adjustment Lock This function locks the OSD in order to maintain the current settings or to prevent the settings from being changed by another person On If you press and hold this button down for 10 seconds the OSD Adjustment Lock func tion is activated Off If you press and hold this button down for 10 seconds again the OSD Adjustment Lock function is disabled Even if the OSD Adjustment Lock function is activated users can still use that function key to adjust the brightness contrast and also can exit the OSD B 0 1 When OSD is not displayed press this button to power on off the monitor 2 When OSD is displayed press this butto
17. IDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center NORTH AMERICA U S A 1 800 SAMSUNG 726 7864 http www samsung com CANADA 1 800 SAMSUNG 726 7864 http www samsung com ca English http www samsung com ca fr French MEXICO 01 800 SAMSUNG 726 7864 http www samsung com LATIN AMERICA ARGENTINE 0800 333 3733 http www samsung com BOLIVIA 800 10 7260 http www samsung com BRAZIL 0800 124 421 http www samsung com 4004 0000 CHILE 800 SAMSUNG 726 7864 http www samsung com From mobile 02 482 82 00 COLOMBIA 01 8000112112 http www samsung com COSTA RICA 0 800 507 7267 http www samsung com latin Spanish http Awww samsung com latin_en English DOMINICA 1 800 751 2676 http www samsung com latin Spanish http Awww samsung com latin_en English ECUADOR 1 800 10 7267 http www samsung com latin Spanish http Awww samsung com latin_en English EL SALVADOR 800 6225 http www samsung com latin Spanish http Awww samsung com latin_en English GUATEMALA 1 800 299 0013 http www samsung com latin Spanish http Awww samsung com latin_en English HONDURAS 800 27919267 http www samsung com latin Spanish http www samsung com latin en English JAMAICA 1 800 234 7267 http www samsung com 5 3 More Information LATIN AMERICA NICARAGU
18. and adjust the resolution Windows 7 Go to Control Panel Appearance and Personalization Display Adjust resolution and adjust the resolution Windows 8 Go to Settings Control Panel Appearance and Personalization Display Adjust resolution and adjust the resolution How do set power saving mode Windows XP Set power saving mode in Control Panel Appearance and Themes Display Screen Saver Settings or BIOS SETUP on the PC Windows ME 2000 Set power saving mode in Control Panel Display Screen Saver Settings or BIOS SETUP on the PC Windows Vista Set power saving mode in Control Panel Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC Windows 7 Set power saving mode in Control Panel Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC Windows 8 Set power saving mode in Settings Control Panel Appearance and Personalization Personalize gt Screen Saver Settings or BIOS SETUP on the PC 4 3 Troubleshooting 5 More Information 5 1 Specifications MODEL NAME 524B240BL S24B240KL 27B240B S27B240K Panel Size 23 6 inches 59 cm 27 inches 68 cm Display area 521 28 mm H x 293 22 mm V 597 89 mm H x 336 31 mm V Pixel Pitch 0 2715 mm H x 0 2715 mm V 0 3114 mm H x 0 3114 mm V Synchroniza Horizonta
19. choose input signal Is the lt Not Optimum Mode message displayed on the screen This occurs when the signal from the graphics card exceeds the maximum resolution or the maximum frequency of the product In this case set up the appropriate resolution and the fre quency for the product Is a blank screen displayed and does the power LED blink at a 1 second interval 1 This occurs when the power saving function is running If you click the mouse or press any key the screen will be turned on 2 If the lt Check Signal Cable gt condition persists for more than five minutes the power saving function will be activated Did you connect with a DVI cable If you connect the DVI cable when the PC has booted up or if you reconnect the DVI cable after disconnecting the cable while using a PC the screen may not be displayed because some graphics cards do not output the video signal In this case reboot the PC while the DVI cable is connected THE IMAGE IS TOO LIGHT OR TOO DARK Adjust the lt Brightness gt and lt Contrast gt Refer to the lt Brightness gt lt Contrast gt fz SAMSUNG Magic Bright is set to lt Dynamic Contrast gt the display brightness can differ according to the input signal THE COLOR IS WEIRD THE PICTURE IS DISPLAYED IN BLACK AND WHITE Is the entire screen displayed in the same color as if viewing the screen through a cellophane paper Check the cable con
20. displayed in full screen regardless of the aspect ratio of the input signal A signal not in the standard mode table is not supported e Ifthe resolution is set to the optimal resolution the aspect ratio does not change whether the sImage Size is set to lt Auto gt or lt Wide gt AV signals e lt 4 3 gt Displays pictures at the 4 3 aspect ratio e lt 16 9 gt Displays pictures at the 16 9 aspect ratio e Screen Fit If a 720P or 1080P signal is input in DVI input mode the picture is displayed as is without truncation This can only be set when the external input is connected through DVI and lt PC AV Mode is set to lt AV gt Language Select a language for the OSD Deutsch English Espanol Frangais Italiano Magyar Polski Portugu s Pycekn Svenska T rk e A W 5 Di The selected language is only applied to the product OSD This setting does not affect the other functions of the PC Using the product 3 4 MENU DESCRIPTION Using this menu you can change the input signal Analog DVI If the monitor is in power saving mode or is displaying the message lt Check Signal Cable gt Source press MENU to display the OSD In this OSD press C3 and MENU F to change the input signal Analog DVI You can exit the OSD Shows the frequency and resolution set on the PC Language Source Exit Analog Exit kHz Hz NP
21. he manufacturing of this product approximately 1 pixel per million 1ppm may appear brighter or darker on the panel This does not affect product performance More Information 5 1 USA ONLY Dispose unwanted electronics through an approved recycler To find the nearest recycling location go to our website www samsung com recyclingdirect or call 877 278 0799 5 1 More Information 5 2 Power Saving Function This monitor has a built in power management system called PowerSaver This system saves energy by switching your monitor to low power mode when it has not been used for a certain amount of time The monitor automatically returns to normal operation when you press a key on the keyboard For energy conservation turn your monitor OFF when it is not needed or when leaving it unattended for long periods The PowerSaver system operates with a VESA DPM compliant video card installed in your computer Use the software utility installed on your computer to set up this feature STATE NORMAL OPERATION POWER SAVING MODE POWER OFF Power Indicator On Blinking Off Power Consumption 30 watts Typical 0 3 watts Typical 0 3 watts S24B240BL S24B240KL Power Consumption 40 watts Typical 0 4 watts Typical 0 4 watts S27B240B 527B240K If there is no power cut off switch the power consumption is 0 only when the power cord is disconnected More Information 5 2 5 3 Contact SAMSUNG WORLD W
22. he product to the D Sub port of the PC with the D Sub cable e When the graphics card provides DVI lt Digital gt output e Connect the DVI IN port of the product to the DVI port of the PC with the DVI cable DVI IN oh N HAHHA The DVI IN terminal is supplied for the digital DVI dedicated models only e Connect the power adapter to DC jack on the rear of the product Connect the power cord to the adapter and wall socket Installing the Product 2 3 The input voltage is switched automatically When the product is connected to a PC you can turn the product on and use it Cables can be fixed as shown 2 3 Installing the Product 2 4 Kensington Lock A Kensington Lock is an anti theft device that enables users to lock the product so that they can safely use it in public locations Since the shape and usage of the locking device may differ depending on the model and the manufacturer for more information refer to the User Manual supplied with the locking device for more information You must purchase the Kensington Lock separately a 1 Wrap the Kensington lock cable around a large stationary object such as a desk or chair To lock the product follow these steps 2 Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable 3 Insert the locking device into the Kensington slot on the Monitor 4 Lock the lock
23. hen booting up the computer please request service for the computer Troubleshooting 4 2 4 3 FAQ FAQ PLEASE TRY THE FOLLOWING How can change the frequency Set the frequency on your graphics card Windows XP Go to Control Panel Appearance and Themes Display Settings Advanced Monitor and adjust Refresh rate under Monitor Settings Windows ME 2000 Go to Control Panel Display Settings Advanced Monitor and adjust Refresh rate under Monitor Settings Windows Vista Go to Control Panel Appearance and Personalization Personalization Display settings Advanced settings Monitor and adjust Refresh rate under Monitor Settings Windows 7 Go to Control Panel Appearance and Personalization Display Screen Resolution Advanced settings Monitor and adjust Refresh rate under Monitor Settings Windows 8 Go to Settings Control Panel Appearance and Personalization Display Screen Resolution Advanced settings Monitor and adjust Refresh rate under Monitor Settings How can change the resolution Windows XP Go to Control Panel Appearance and Themes Display Settings and adjust the resolution Windows ME 2000 Go to Control Panel Display Settings and adjust the resolution Windows Vista Go to Control Panel Appearance and Personalization Personalize Display settings
24. ing service company or partner of Samsung Electronics Co Ltd remodeling or repairing the product by customer using it with incorrect voltage or non authorised electrical connections not following the cautions in User Manual Others If product fails by natural disaster lightning fire earthquake flood damage etc If consumable components are all used up Battery Toner Fluorescent lights Head Vibrator Lamp Filter Ribbon etc If customer requests a service in case the product has no defect service fee may be charged So please read User Manual first More Information 5 4 5 5 Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please sepa rate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of mate rial resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe rec
25. l 30 81 kHz pai Vertical Do 75 Mg Display Color 16 7 M Resolution Optimum resolution 1920 x 1080 60 Hz Maximum resolution 1920 x 1080 60 Hz Input Signal Terminated RGB Analog DVI Digital Visual Interface Compliant Digital RGB 0 7 Vp p 5 Separate H V sync Composite SOG TTL level V high 2 2 0V V low s 0 8V Maximum Pixel Clock 164MHz Analog Digital Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal Cable 15pin to 15pin D sub cable Detachable DVI D to DVI D connector Detachable Dimensions WxHxD Weight 558 5 x 361 2 x 49 4 mm 22 0 x 14 2 x 1 9 inches Without Stand 558 5 x 432 1 x 222 7 mm 22 0 x 17 0 x 8 77 inches With Stand 8 6 Ibs 3 9 kg 644 8 x 414 2 x 50 7 mm 25 4 x 16 3 x 2 0 inches Without Stand 644 8 x 485 2 x 222 7 mm 25 4 x 19 1 x 8 77 inches With Stand 9 7 lbs 4 4 kg Environmental Operating Operating Temperature 50 F 104 F 10 C 40 C considerations Humidity 10 80 non condensing Storage Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 95 non condensing Tilt 1 0 2 0 20 0 2 0 Design and specifications are subject to change without prior notice This device is a Class B digital apparatus Panel Dots Pixels Due to the nature of t
26. n to access sub OSD or activate the OSD menu Power LED This LED is turned on when the product works normally For more information on the power saving function refer to the power saving function in More Information When not using the product for a long time unplugging the power cord is recommended to minimize power consumption Using the product 3 3 3 4 Using the Screen Adjustment Menu OSD On Screen Display The Screen Adjustment Menu OSD On Screen Display Structure TOP MENUS SUB MENUS MAGIC Bright Brightness Contrast Gamma Auto Adjustment PC AV Mode Image Size Language Source Exit Monitor functions may vary according to models Please refer to actual product Custom ES 100 OOOO p aeBright Brightness Contrast Gamma Mode Auto Adjustment PC AY Mode Screen Fit Image Size F Language English Source OVI Exit MENU DESCRIPTION Provides preset picture settings optimized for various user environments such as editing a document surfing the Internet playing games or movies and so on e lt Custom gt If the preset picture modes are not sufficient users can configure the lt brightness gt and lt Contrast gt directly using this mode e lt Standard gt This mode provides the picture setting appropriate for editing a document and surfing the Internet Cute text picture MAGIC Bright Gane This mode provide
27. nection to the computer Reinsert the graphics card into the computer completely Is the graphics card configured correctly Set up the graphics card referring to the user manual THE DISPLAY AREA SUDDENLY MOVES TO AN EDGE OR TO THE CENTER Did you change the graphics card or the driver Turn on Auto Adjustment function in the OSD menu Did you change the resolution and frequency appropriate to the product Set the resolution and the frequency to the appropriate values in the graphics card refer to the Standard Signal Mode Table Is the graphics card configured correctly Set up the graphics card referring to the user manual 4 2 Troubleshooting THE PICTURES ARE OUT OF FOCUS Did you change the resolution and the frequency appropriate to the product Set the resolution and the frequency to the appropriate values in the graphics cardrefer to the Standard Signal Mode Table THE COLOR IS DISPLAYED IN 16 BIT 16 COLORS THE COLOR HAS BEEN CHANGED AFTER CHANGING THE GRAPHICS CARD Did you install the device driver for the product Windows XP Set the color again by selecting Control Panel Appearance and Themes Display Settings Windows ME 2000 Set the color again by selecting Control Panel Display Settings Windows Vista Change the color settings by selecting Con trol Panel Appearance and Personalization Personaliza tion Dis
28. ntainer such as a vase flowerpot beverage cosmetics or drugs or a metal object over the product e f water or an alien substance enters the product turn the power off unplug the power cord and contact a service center e Otherwise it may result in a problem with the product electric shock or fire A Caution Displaying a still image for a long time may create a persistent image or stain on the screen e Ifyou do not use the product fora long time use the power saving mode or set the screensaver to the moving picture mode Set the appropriate resolution and fre quency for the product e Otherwise it may result in eye strain Do not place the adapter on top of another adapter e Otherwise it may result in fire Remove the vinyl cover of the adapter before using the adaptor Ae e Otherwise it may result in fire KI o Be careful that adaptor should not be in fi contact with water and therefore not be wet po ap y e This may cause a malfunction electric pas shock or fire Do not use adaptor bythe waterside or outside particularly when it rains or snows Be careful that adaptor should not be wet while cleaning floor with water Avoid using a humidifier or cooker near the product e Otherwise it may result in electric shock or fire Avoid inserting metal objects such as a chopsticks coins or hairpins or inflamma ble objects into the product the vent
29. ons it may result in a problem with the product or fire Major Safety Precautions Avoid installing the product in a location exposed to dust moisture sauna oil smoke or water rain drops and installing it within a vehicle e This may result in electric shock or fire Avoid installing the product at an easily reachable height where children may reach it e Ifa child touches the product the product may fall and this may result in injury e Since the front part is heavier install the product on a flat and stable surface A Caution Do not let the product drop while moving it e This may result in a problem with the product or injury When installing the product on a console or shelf make sure that the front of the product does not protrude out of the console or shelf e Otherwise this may cause the product to fall off and result in a malfunction or injury e Make sure to use a cabinet or shelf suitable to the size of the product If the product is installed in a location where the operating conditions vary considerably a serious quality problem may occur due to the surrounding environment In this case install the product only after consulting one of our service engineers about the matter e Places exposed to microscopic dust chemicals too high or low temperature high humidity such as airports or stations where the product is continuously used for a long time and so on
30. play settings Windows 7 Change the color settings by selecting Control Panel Appearance and Personalization Display gt Adjust resolution Advanced settings Monitor Windows 8 Change the color settings by selecting Settings Control Panel Appearance and Personalization Dis play Adjust resolution Advanced settings Monitor For more information refer to the Windows user manual for the computer Is the graphics card configured correctly Configure the color again in accordance with the new graph ics card driver WHEN I CONNECT THE MONITOR THE UNKNOWN MONITOR PLUG amp PLAY VESA DDC MONITOR FOUND MESSAGE IS DISPLAYED Did you install the device driver for the product Install the device driver referring to the descriptions about the driver installation Check if all the Plug amp Play VESA DDC functions are sup ported referring to the User Manual of the graphics card Install the device driver referring to the descriptions about the driver installation WHEN I LOOK AT THE EXTERIOR EDGES OF THE PRODUCT SMALL ALIEN SUBSTANCES APPEAR ON IT Since this product is designed so that the color has a soft appearance by coating it with a transparent material over the black edges such things may be seen This is not a defect of the product A BEEP BEEP SOUND IS HEARD WHEN BOOTING THE COMPUTER If the beep sound is generated 3 or more times w
31. s ports etc e If water or an alien substance enters the product turn the power off unplug the power cord and contact a service center e Otherwise it may result in a problem with the product electric shock or fire When not using the product for a long time such as leaving your home unplug the power cord from the wall outlet e Otherwise it may cause dust accumulation and result in fire caused by overheating or short circuit or result in an electric shock Avoid turning the product upside down or move the product holding only the stand e This may cause the product to fall resulting in damage to the product or injury Keep power adaptor away from any other heat source e Otherwise it may result in fire Always keep power adaptor in well venti lated area Watching the product from too close a dis tance continuously may damage your eye sight It is important to give your eyes some rest 5 minutes every hour when viewing the prod uct screen for long periods of time e This will alleviate any eye strain 1 4 Major Safety Precautions Since the display panel is hot after using it Keep small accessories away from the chil for a long time do not touch the product gt dren Take care when adjusting the angle of the product or the height of the stand Avoid placing a heavy object over the prod uct e If your hand or finger is caught you may be injured e Otherwise it may result
32. s the picture setting appropriate for playing games that include lots of graphics and that require a fast screen refresh rate e lt Cinema gt This mode provides brightness and sharpness settings similar to those of a TV for the best entertainment environment movie DVD etc e Dynamic Contrast gt Controls the picture contrast automatically so that bright and dark pictures are balanced overall Controls the screen brightness Brightness SAMSUNG This menu is unavailable when Mage Bright is set to Dynamic Contrast gt mode 3 4 Using the product MENU DESCRIPTION Contrast Controls the contrast of the pictures displayed on the screen This menu is unavailable when lt faaie Bright is set to Dynamic Contrast gt or Cinema mode Gamma Using this menu you can change the intensity of the colors of medium brightness e sMode17 lt Mode2 gt lt Mode3 gt This menu is unavailable when lt Aare Bright is set to Dynamic Contrast gt or lt Cinema gt mode Auto Adjustment You can adjust the screen settings automatically This function is only available in Analog mode PC AV Mode Set to PC when connected to a PC Set to AV when connected to an AV device This function does not support Analog mode Image Size PC signals e lt Auto gt The picture is displayed at the aspect ratio of the input signal e lt Wide gt The picture is
33. sponsibility for the Pay Service Cost to Customers When the service is requested in spite of in warranty we may charge you for a visit from a service technician in the following cases Not a product defect Cleaning of the product Adjustment Explanation Re installation and etc If a service technician gives instructions on how to use product or simply adjusts options without disassembling product If a defect is caused by external environmental factors Internet Antenna Wired Signal etc If a product is reinstalled or devices are connected additionally after installing the purchased product for the first time If a product is reinstalled to move to a different spot or to move to a different house If customer requests instructions on how to use because of another company s product If customer requests instructions on how to use the network or another company s program If customer requests software installation and setup for the product If a service technician removes cleans dusts or foreign materials inside of the product If customer requests an installation additionally after purchasing a product through home shopping or online A Product damage caused by customer s fault Product damage caused by customer s mishandling or wrong repair If a product damage is caused by external impact or drop use of supplies or separatly sold product unspecified by Samsung repair from a person besides an engineer of outsourc
34. ty Precautions 1 2 Custody and Maintenance Securing the Installation Space e Keep the required distances between the product and other objects e g walls to ensure proper ventilation Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature Install the product so the required distances shown in the figure are kept The appearance may differ depending on the product When installing the product with a stand 10cm 10 om 3 93 inches 3 93 inches About persistent images e Displaying a still image for a long time may create a persistent image or stain on the screen If you do not use the product for a long time set the power saving mode or screen saver 1 2 Major Safety Precautions 1 3 Cleaning the Monitor Cleaning the Monitor e The panel and exterior of the cutting edge monitor scratch easily and require careful attention Clean the monitor according to the following steps 1 Power off the monitor and PC 2 Disconnect the power cable from the monitor To avoid electric shock be sure you disconnect the cable by gripping the plug and do not touch the cable with wet hands 3 Wipe the monitor using a soft slightly damp cloth that has been squeezed e Do not use a cleaning agent that contains alcohol or solvents or that is surface active Otherwise the exterior may discolor or crack or the panel coating may come off e Do not spray
35. u Start Icons used in this manual ICON NAME MEANING GB Caution Indicates cases where the function may not work or the setting may be canceled Note Indicates a hint or tip to operate a function Using this Manual e Make yourself fully aware of the safety precautions before using this product e Ifa problem occurs refer to the Troubleshooting section Copyright Notice The contents of this manual are subject to change without prior notice for performance improvement Copyright 2012 Samsung Electronics Co Ltd All Rights Reserved The copyright of this manual is reserved by Samsung Electronics Co Ltd The contents of this manual may not be partially or in whole reproduced distributed or used in any form without the written permission of Samsung Electronics Co Ltd Microsoft Windows and Windows NT are the registered trademarks of Microsoft Corporation VESA DPM and DDC are the registered trademarks of the Video Electronics Standard Association e An administration fee may be charged if either e a an engineer is called out at your request and there is no defect in the product i e where you have failed to read this user manual e b you bring the unit to a repair centre and there is no defect in the product i e where you have failed to read this user manual e The amount of such administration charge will be advised to you before any work or home visit is carried out Major Safe
36. w samsung com MIDDLE EAST BAHRAIN 8000 4726 http www samsung com ae English http www samsung com ae ar Arabic EGYPT 08000 726786 http www samsung com IRAN 021 8255 http www samsung com JORDAN 800 22273 http www samsung com 065777444 KUWAIT 183 2255 http www samsung com ae English http www samsung com ae ar Arabic MOROCCO 080 100 2255 http www samsung com More Information 5 3 MIDDLE EAST OMAN 800 SAMSUNG 726 7864 http www samsung com ae English http www samsung com ae ar Arabic SAUDI ARABIA 9200 21230 http www samsung com ae English http www samsung com ae ar Arabic TURKEY 444 77 11 http www samsung com U A E 800 SAMSUNG 726 7864 http www samsung com AFRICA ANGOLA 91 726 7864 http www samsung com BOTSWANA 0800 726 000 http www samsung com CAMEROON 7095 0077 http www samsung com COTE D IVOIRE 8000 0077 http www samsung com GHANA 0800 10077 http www samsung com 0302 200077 KENYA 0800 724 000 http www samsung com NAMIBIA 8197267864 http www samsung com NIGERIA 0800 726 7864 http www samsung com SENEGAL 800 00 0077 http www samsung com SOUTH AFRICA 0860 SAMSUNG 726 7864 http www samsung com TANZANIA 0685 88 99 00 http www samsung com UGANDA 0800 300 300 http www samsung com ZAMBIA 211350370 http www samsung com 5 3 More Information 5 4 Re
37. ycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal 9 5 More Information
Download Pdf Manuals
Related Search
Related Contents
Blanco Single Bowl Undermount 509-338 User's Manual Computer Gear 26-1002B SATA cable Nettoyant EB + Pyrevol + Pyregale PowerFactory 15 What`s New 0-90° / 0.1° V7 Professional II Frontloader Notebook Case 16" Accéder au document ERL I/O Expansion IED Ordering Template 取扱説明書 COOLROBO ST ご使用前に必ずご確認ください Copyright © All rights reserved.