Home

Samsung 4 Burner Gas Hob (GN642FFXD) User Manual

image

Contents

1. A SEALING STRIP of the screws There are one set of screw holes in each corner of the hob H Ti Slightly tighten a screw C through the bracket B so that the bracket is attached to the hob but so that you a can still adjust the position it 2 Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out 3 On the underneath of the hob adjust the brackets into a position that is suitable for your worktop Then fully tighten the screws C to secure the hob into position C SCREW B BRACKET A duplicate data label is supplied for AN adhesion to an accessible location near the appliance if the data label on the base of the appliance cannot be accessed when the appliance is installed 21 upside down and place it on a cushioned mat Gas Connection m This appliance must be installed and connected in accordance with installa tion regulation in force in country in which the appliance is to be used m This appliance is supplied to run on natural gas only and cannot be used on any other type of gas without modification m To use on LPG the injectors must be changed using the conversion kit supplied Refer LPG conversion on page 24 Conversion must only be undertaken by a qualified person m The appliance must be connected to gas supply with upstream connection of an isolation v
2. m Do not spray aerosols in the vicinity of m Ensure the control knobs are in the this appliance while it is in operaiton OFF position when not in use m This appliance is intended for domestic cooking only It is not designed for commercial or industrial purposes m Prolonged intensive use of the appliance may call for additional ventilation for example opening of a window or increasing the level of mechanical ventilation where present m Use heat resistant pot holders or gloves when handing hot pots and pans m Take care not to let pot holders or gloves get damp or wet as this causes heat to transfer through the material quicker with the risk of burning yourself m Only ever use the burners after placing pots and pans on them Do not heat up any empty pots or pans m Never use plastic or aluminium foil dishes on the appliance m Vhen using other electrical appliances ensure the cable does not come into contact with the appliance surfaces of the cooking appliance m If you have any mechanical substance such as artificial heart and etc in your body consult with a doctor before using the appliance Cleaning amp Service m Never use abrasive or caustic cleaning agents m This appliance should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used row wv SQ m Before attempting to clean the appliance it should be disconnected from the
3. PANS AN m User can t use cooking pan D min D max on the appliance that overlap Rapid 200mm 260mm its edge Semi Rapid 130mm 180mm Auxiliary 100mm 120mm NO YES Do not use small diameter cookware on Always use cookware that are a large burners suitable for each burner so as The flame should never come up the to avoid wasting gas and SEE sides of the cookware discolouring the cookware Never cook without a lid or with the lid Always place the lid on the e half off cookware you are wasting energy spe Do not use a pan with a convex or Only use pots saucepans and concave bottom frying pans with thick flat HR bottom Do not place cookware on one side of a burner as if could tip over Do not use cookware with a large diameter on the burners near the controls which when placed on the middle of the burner may touch the controls or be so close to them that they increase the temperature in this area and may cause damage Always place the cookware right over the burners not to one side KIK OX ROKK Never place cookware directly on top of the burner Do not place anything eg flame tamer asbestos mat between pan and pan support as serious damage to the appliance may result Place the cookware on top of DI the trivet Do not use excessive weight and do not hit the hob with heavy objects Handle cookware carefully when they are on the burner simultane
4. Make sure that the connection is the coupling and the gas bottle airtight D m lf problem is not solved please contact the SamSung customer care center 16 Application for Service If you have any comments or questions regarding a Samsung products contact the SAMSUNG customer care center Region Country Genter TEL Web Site FAX no Address Remark www 612 Samsung Electronics Australia AUSTRALIA 1300 362 603 samsung com au 9763 5750 7 Parkview Drive Homebush Bay NSW 2127 ww 03 Samsung Malaysia Electronics Sdn Bhd MALAYSIA 1800 88 9999 j a 3B 1 1 Level 1 Block 3B Plaza Sentral Jalan Stesen Asi samsung com my 22636759 Sentral 5 KL Sentral 50470 Kuala Lumpur Malaysia Pasie Thai Samsung Electronics Co Ltd Service Department 1 6 floor Boonmitr Building 138 Silom Rd Suriyawong THAILAND 1800 29 323202 www 02 Bangrak Bangkok 10500 689 3232 samsung com th 689 3298 ui lnaduefadtaalusiad ania lawn 138 Mensuaiias Tu 1 6 auudau uuu LUAUNISA NFIMMAY 10500 www Samsung Electronics Benelux B V BELGIUM 02 201 2418 samsung be N A Medialaan 50 1800 Vilvoorde Belgium CZECH www Distributor pro eskou republiku Samsung Zrt eska REPUBLIC 844 000 844 samsung com cz NIA organiza n slo ka Vysko ilova 4 14000 Praha 4 www Samsung Electronics Nordic AB DENMARK 7070 19 70 sams
5. a kitchen unit or 600mm worktop providing the following minimum distances are allowed The edge of the appliance must be a minimum distance of 55mm from a rear wall A minimum distance of 100mm must be left between the side edges of the appliance and any adjacent cabinets or walls The minimum distance combustible material can be fitted above the appliance in line with the edges of the appliance is 400mm If it is fitted below 400mm a space of 50mm must be allowed from the edges of the appliance The minimum distance combustible material can be fitted directly above the appliance is 700mm J vy 4 40mm E t 7 150mm MAX This panel a must be positioned at a maximum distance of 150mm below the worktop 20 Installing the appliance 1 Remove the trivets the burner lid and flame spreader and carefully turn the appliance 177 Take care that the Ignition devices and flame supervision devices are not damaged in this operation 2 Apply the sealing strip provided around the edge of the appliance 3 Do not leave a gap in the sealing agent or overlap the thickness Do not use a silicon sealant to seal the AN appliance against the aperture This will make it difficult to remove the appliance from the aperture in future particularly if it needs to be serviced 1 Place the bracket B over the holes that match the size
6. m This appliance must be installed by an authorised technician or installer m Prior to installation ensure that the local distribution conditions nature of the gas and gas pressure and the adjustment of the appliance are compatible m The adjustment conditions for this appliance are stated on the label or data plate m This appliance is not connected to a combustion products evacuation device It shall be installed and connected in accordance with current installation regulations Particular attention shall be given to the relevant requirements regarding ventilaton m Before installing turn off the gas and electricity supply to the appliance m All appliances containing any electrical components must be earthed m Ensure that the gas pipe and electrical cable are installed in sucha way that they do not touch any parts of the appliacne which become hot m Gas pipe or connector shouldn t be bent or blocked by any other appliances m Check the dimensions of the appliance as well as the dimensions of the gap to be cut in the kitchen unit m The panels located above the work surface directly next to the appliance must be made of non flammable material Both the strati fied surfacing and the glue used to secure it should be heat resistant to prevent deterioration m Turn on appliance tap and light each burners Check for a clear blue flame without yellow tipping If burners shows any abnormalties check the following Bu
7. the hob as soon as possible to avoid the risk of corrosion m Stainless steel parts of the appliance may become discoloured over time This is normal because of the high temperatures Each time the appliance is used these parts should be cleaned with a product that is suitable for stainless steel 14 Cleaning and Maintenance Continued BURNERS m Remove the burner lids and Flame Spreaders by pulling them upwards and away from the top plate m Soak them in hot water and a little detergent m After cleaning and washing them wipe and dry them carefully Make sure that the flame holes are clean and completely dry m Wipe the fixed parts of the burner cup with a damp cloth and dry afterwards m Gently wipe the Ignition device and flame supervision device with a well wrung out cloth and wipe dry with a clean cloth m Before placing the burners back on the top plate make sure that the injector is not blocked a Re assemble the Auxiliary Semi Rapid and Rapid burners as follows 1 Place the flame spreader 15 on to the burner cup 16 so that the ignition device and the flame supervision device extend through their respective holes in the flame spreader The flame spreader must click into place correctly 2 Position the burner lid 14 onto the flame speader 15 so that the retaining pins fit into their respective recesses Replace parts in the correct order after cleaning Do not mix up the top and bottom The loca
8. alve in accordance with the respectively valid regulations We recommed that the isolation valve be fitted prior to the appliance to enable isolation of appliance from gas supply The valve must be easily accessible at all times m For your safety you must choose from the two following connection option A Connection with a rigid pipe B Connection with flexible hose Hose assemblies should be certified as conforming to AS NZS 1869 10mm ID class B or D no more than 1 2m long and in accordance with AS 5601 m An appliance regulator is provided The regulator must be positioned so that the pressure test nipple is accessible when the appliance is installed m A propane fitting is not provided the propane fitting must be installed between the piping amp the appliance for the pressure to be checked to ensure it is operating at 2 60kPa 1 Remove plastic cap from gas supply line prior to installation 2 Fit regulator natural gas or propane fitting LPG directly to the elbow 1 2 tapered thread Direction of gas flow is indicated on the rear of the regulator 3 The inlet of the regulator is a 1 2 parallel thread and is connected to consumer piping or flexible hose 4 Check the outlet gas pressure 70mm Natural gas connection LPG connection inna 36mm Elbow Elbow 1 2 Taperd 1 2 Taperd f thread thread Sealing sulle washer an Presu tal Pressure r test poine tes
9. as a grounding pin and two flat current carrying pins forming an upside down V shape 10A 3 Pins Flat Earth 1 MICRO SWITCHES 2 IGNITER 23 Gas Conversion T m Be careful the operations and adjustments to be carried out when converting from one gas to another m All work must be carried out by a qualified technician m Before you begin turn off the gas and electricity supply to the appliance m Change the gas connection and check the outlet gas pressure Refer gas connection on page 22 1 Change the injector of the burners Remove the trivets Burner lid and Flame spreader Unscrew the injector using a 7mm box spanner and replace it with the stipulated injector for new gas supply see table 1 Page 25 Carefully reassemble the all components After injectors are replaced it is advisable to strongly tighten the injector in place Adjusting of the valves of the cooking hob burners for reduced consumption Turn the valves down to minimum C d Control handle A Remove the control handles from valves Adjusting the by pass screw For converting NG into LPG the screw must be screwed down fully tight At this stage light up the burners and turn the Tap control handles from max position to minimum position to check flame stability by pass screw For converting LPG into NG please contact After Sales Service Replace the control handles on the valves Do not dismantle t
10. ex Installation and User Manual GN641FFXD GN641FFBD GN642FFXD GN642FFBD Gas cooktop P N 50550 65080 IS C Preface Thank you for choosing our appliance To use this appliance correctly and prevent any potential risk read these instructions before use the appliance Keep these instructions at the place where you can find it easily If you are unsure of any of the information contained in these instructions please contact the SamSung customer care center These instructions are only valid for the countries of destination the identification symbols of which are indicated on the cover of the instruction manual The manufacturer shall not be held responsible for any damages to persons or property caused by incorrect installation or use of the appliance The appliance has been certified for use in countries other than those stated on the appliance The manufacturer also reserves the right to make any modifications to the products as may be considered necessary or useful also in the interests of the user without jeopardizing the main functional and safety feafures of the products themselves Safety Warning m Your safety is of the utmost importance to SamSung m You must read warnings carefully before installing or using the appliance m This instruction booklet must be kept with the appliance for any future reference If the appliance is sold or transferred to another person ensure the booklet is passed on to the
11. he valve shaft in the event of a malfunction change the whole valve m Before placing the burners back on the top place make sure that the injector is not blocked a A full operational test and a test for possible leakages must be carried out after gas conversion such as soap water or gas detector 24 Burner Features Table 1 TYPE OF GAS BURNER Rapid Semi rapid Auxiliary Total SRESSURE POSITION Max Min Max Min Max Min Injector make NG 1 100 mm 157 119 89 RA uh gas consumption 108 25 68 15 40 08 280 Injector make LPG 1 100 mm 92 72 54 2 60kPa VOe gas consumption gg 2 5 6 8 15 40 08 280 Nominal gas consumptions for LPG are based on propane gas Burner Calibrated orifice 1 100mm Auxiliary 31 Semi rapid 34 Rapid 43 Aeration adjustment none 25 MEMO 26
12. mains and cool m You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance Environmental Information m After installation please dispose of the packaging S with due regard to safety and the environment Z m When disposing of an old appliance make it unusable by cutting off the cable K Correct Disposal of This Product Waste Electrical amp Electronic Equipment m This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources m Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling m Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal Description of the appliance 1 Top Plate 2 Auxiliary Burner 3 Semi rapid Burner 4 Rapid Burner 5 Control handle for rear left burner Rapid burner 6 Control handle for front left burner Auxiliary burner Handle 11 Cont
13. new user m The manufacturer declines any liability should these safety measures not be observed m The following marks are made to be easily understood so that you can prevent any safety accident caused by misuse in advance and use the appliance more conveniently m Completely understand the following contents before read the instruction If this mark is neglected the user may be dead or seriously A Danger Warning injured AN E If this mark is neglected the user may be injured or damaged Caution in property a The following marks mean as follow AN genera Danger Warning and Caution N No Access amp No Fire Tool D Must Do a If gas seems to leak take the actions as follow Do not turn on the light Do not switch on off any electrical appliance and do not touch any electric plug Do not use a telephone 1 Stop using the product and close the middle valve 2 Open the window to ventilate Contact our service center by using a phone outside C2 NI US N The fuel gas contains mercaptan so that you can feel that the gas leaks even where only 1 1000 of the gas exists in the air with specific smell smell of rotten garlic or egg 69 Installation m This appliance shall be installed in accordance with regulations in force and only used in a well ventilated space m Where this appliance is installed in marine craft o
14. ously by several burners because the resulting heat build up A m lt is not permitted to use roasting pans frying pans or grill stones heated may damage the appliance m Do not touch the top plate and trivet while using or for a certain period after using barely keep the liquid simmering 13 m As soon as a liquid starts boiling turn down the flame so that it will Cleaning and Maintenance A m Cleaning operations must only be carried out when the appliance is cool m The appliance should be disconnected from your mains supply before commencing any cleaning process m Clean the appliance regularly preferably after each use m Abrasive cleaners or sharp objects will damage the appliance surface you should clean it using water and a little washing up liquid Usable Unusable GF Soft lothing Metal Brush Sponge Brush Nylon Brush Edible Oil i Acidic Alkali Detergent i NeutrabDetergent Abrasive Thinner Benzene o Trivets Control handles m Take off the Trivets m Clean these and the control handles with a damp cloth washing up liquid and warm water Stubborn soiling is best soaked before m Finally dry everything with a clean soft cloth Top plate m Regularly wipe over the top plate using a soft cloth well wrung out in warm water to which a little washing up liquid has been added m Dry the top plate thoroughly after cleaning m Thoroughly remove salty foods or liquids from
15. persons whose physical sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safety without supervision or instruction by a responsible person to ensure that they can use the appliance safety During Use m Only use the appliance for preparing m Do not modify this appliance food m The use of a gas cooking appliance results Do not use this appliance if it is in in the production of heat and moisture in contact with water Do not operate the room in which it is installed Ensure this appliance with wet hands that the kitchen is well ventilated keep natural ventilation holes open or install a mechanical ventilation device mechanical extractor hood m The heating and cooking surfaces of m Do not use large cloths tea towels or the appliance become hot when they similar as the ends could touch the are in use take all due precautions flames and catch fire m Never leave the appliance unattended m Unstable or misshapen pans should when cooking with oil and fats If fat not be used on the appliance as and oil overheats then it can ignite unstable pans can cause an accident extremely quickly by tipping or spillage During Use Continued m Do not use or store flammable materials in the appliance storage drawer or near this appliance m Perishable food plastic items and aerosols may be affected by heat and should not stored above or below the appliance
16. ponding cooking position has boiled over or if there was a sudden draught m Fully press down the control handle for the corresponding cooking position and turn it to the m In the event of the burner flames being accidentally extinguished turn left to the ignition position and hold it there for a few seconds at most until the burner ignites off the burner control and do not attemp to re ignite the burner for at m After igniting keep the control handle pressed for about 5 8seconds more because the heat least 1min sensor that opens the gas channel has to warm up first And set control handle to the position you want m If the burner does not light repeat the process m The flame size can be set continuously between maximum and minimum by slowing turning the control handle T m If the igniters are dirty this makes the burner harder to light so you should keep them as clean as possible Do this with a small brush and make sure that the ignition device is not hit or knocked violently m The flame supervision device shall not be operated for more than 15s If after 15s the burner has not lit stop operating the device and open the compartment door and or wait at least 1min before attempting a further ignition of the burner Safety and Energy saving advice The diameter of the bottom of the pan should correspond to that of the burner BURNERS
17. r in caravans it shall not be used as a space heater m Prior to installation ensure that the gas and electrical supply complies with the type stated on the rating plate NG LPG 220v 240v 4 ISO dA m The gas pipe and electrical cable must be installed in such a way that they do not touch any parts or the appliance A N m The gas pressure regulator supplied with appliance must be installed in line with the gas pipe NG only m This appliance should be installed by an authorised technician or installer m The adjustment conditions for this appliance are stated on the label or data plate m After unpacking the appliance make sure the product is not damaged and that the connection cord is in perfect condition Otherwise contact the dealer before installing the appliance m The adjacent furniture and all materials used in the installation must be able to withstand a minimum temperature of 85 C above the ambient temperature of the room it is located in whilst in use m Remove all packaging before using the appliance Child and People Safety m Do not allow children to play near or with the appliance The appliance gets hot when it is in use Children should be kept away until it has cooled m This appliance is designed to be operated by adults m Children can also injure themselves by pulling pans or pots off the appliance m This appliance is not intended for use by children or other
18. rner lid on correctly Flame spreader positioned correctly Burner vertically aligned with injector nipple m A full operational test and a test for possible leakages must be carried out by the fitter after installaion m The flexible hose shall be fitted in such a way that it cannot come into contact with a moveable part of the housing unit and does not pass through any space susceptible of becoming congested 18 Engineers technical data Appliance Specification Positioning m Clearance around the gas appliance must comply with the requirement of AS5601 CLEARANCES REQUIRED WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE Model GN641FFXD GN641FFBD GN642FFXD GN642FFBD Trivet Drawing Cast Iron Top Plate Stainless steel Enamel coating Stainless steel Enamel coating Control Handle Silver color Titan color Silver color Titan color Weight Dimension WxDxh 9 5kg 9 5kg 594 510 50 likg 11kg 594 510 50 600mm 400mm Cut out size Width 560mm Depth 490mm Thickness 30 50mm Ignition device Continuous Ignition Type Gas Connection 1 2 inch female thread Electric supply 220 240V 50 60Hz Burner Feature Rapid 1EA Semi rapid 2EA Auxiliary 1EA 19 FO 0812 FO 0813 m This appliance is to be built into
19. rol handle 12 Sealing ring 13 Valve 12 7 Control handle for front right burner Semi rapid burner 8 Control handle for rear right burner Semi rapid burner 9 Trivet Right 10 Trivet Left 11 Connection Cord Burner Auxiliary Semi rapid and Rapid 10 14 Burner lid 15 Flame Spreader 16 Burner Cup 17 Injector 18 Ignition Electrode 19 Flame supervision device How to Use the Appliance How to Use the Appliance Continued Preparation The following symbols will appear on the control panel next to each control handle o O Circle gas off N Small flame minimum setting C ny N Large flame maximum setting Le Ignition position m The minimum setting is at the end of the anti clockwise rotation of the control handle 60 m All operation positions must be selected between the maximum and minimum position m Turn the control handle to clockwise to setting O off position m The symbol on the control panel next to the control handle will indicate which burner it operates m Close the middle valve Ignition amp Adjustment f 5 AN m Right after extinguishment the appliance is still hot Be careful not to be N a 5 burned A Q NS W co tom Q m This appliance is fitted with a Flame supervision device which cuts off m Open the middle valve S S the supply of gas to a burner if the flame goes out for example if food m Place a pot or a pan on the corres
20. t poine Regulator 5 1 2 parallel thread T m All the fitting thread must use pipe compound or thread sealant m Ensure that the hose does not contact the hot surfaces of any other appliance that may be installed underneath or next to the cooktop m A full operational test and a test for possible leakages must be carried out by the fitter after installation Such a soap water or gas detector 22 Electrical Connection m This appliance must be earthed m This appliance is designed to be connected to a 220 240V 50 60Hz AC electricity supply m The wires in the mains lead are coloured in accordance with the following code Green yellow Earth Blue Neutral Brown Live m As the colours of wires in the mains lead of the this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal in plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marked the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked the letter A or coloured red m The plug to be connected to the power cable and socket must be the same type and must conform to current regulations The plug used in Australia New Zealand h
21. ting pins must fit exactly into the notches 15 Troubleshooting m Repairs to the gas and electrical components of this appliance must only be carried out by a suitably qualified and competent person to ensure safety m However some minor problems can be resolved as follows Problem Probable cause Solution Not ignited No Spark Check the electricity supply The burner lid is badly assembled Assemble the lid correctly The gas supply is closed Open the gas supply completely Badly ignited The gas supply is incompletely Open the gas supply completely opened The burner lid is badly assembled Assemble the lid correctly The ignition plug is contaminated Wipe such alien substance with with alien substance dried clothing The burners are wet Dry the burners lids carefully The holes in the flame spreader Clean the flame spreader are clogged Noise made when The burner lid is badly assembled Assemble the burner lid combusted and ignited correctly Fire off while using The flame supervision device is Clean the flame supervision contaminated with alien substance device Yellow Flame The holes in the flame spreader Clean the flame spreader are clogged Different gas is used Check the gas used Unstable Flame The burner lid is badly assembled Assemble the burner lid correctly Gas Smell A gas tap has been left on Check to see if any gas taps are on There may be a leak between
22. tugal 0800 SAMSUNG www NIA SLOVAKIA 726786 samsung com sk NA ww SAMSUNG ELECTRONICS IBERIA S A SPAIN 902 10 11 30 samgund comes N A Ciencies 55 65 Poligono Pedrosa 9 08908 HOSPITALET DE LLOBREGAT Barcelona www Samsung Electronics Nordic AB SWEDEN 0774400 200 samsung com se NA SE 19427 Kanalvagen 10A Upplands Vasby Sweden UK 0870 SAMSUNG www 0870 Samsung Electronics U K Ltd Customer Care Centre PO i 7267864 samsung com uk 7221127 _ Box 17243 Edinburgh EH11 4YB United Kingdom Republic of WWW 44 0 870 Ireland EE samsung com uk 7221127 i 0800 SAMSUNG http www Switzerland 7267864 samsung com ch NA 200 900 www 7 495 117545 Poccna Mocksa yn JopoxHaa 4 3 Kopn 6 RUSSIA 8 800 200 0400 samsung 783 0556 200 080 www 7 3272 050051 4th floor 172 Dostyk Ave Almaty Republic of RAZAHSTAN 8 800 060 1188 samsung kz 58 59 66 Kazakhstan www 998 71 100 742 12fl International Business Center 107B Amir UZBEKISTAN 8 800 120 0400 samsung uz 120 7208 Temur str Tashkent Uzbekistan 200 509 www 380 44 30A Spaska St Floor 3 Kiev 04070 Ukraine CIS UKRAINE 8 800 502 0000 samsung com ur 537 59 48 WWW 37052 Zemaites 21 Vilnius LT 2009 Lithuania LITHUANIA 8 800 77777 samsung t 439 770 G http www samsung 3717 J Alunana 2 Riga LV 1340 Latvia LATVIA 800 7267 com vindex htm 508480 www ESTONIA 800 7267 samsung ee 17 Technical instructions A m Do not modify this appliance
23. ung com dk NIA SE 19427 Kanalvagen 10A Upplands Vasby Sweden www Samsung Electronics Nordic AB FINLAND 030 6227 515 samsung com fi NA SE 19427 Kanalvagen 10A Upplands Vasby Sweden 3260 SAMSUNG or ail 01 48 Samsung Service Consommateurs FRANCE 08 25 08 65 65 samsung com fr 63 06 38 66 rue des Vanesses BP 50116 Villepinte 95950 0 15 Min g ROISSY cedex France Samsung Electronics GmbH GERMANY ORDAM ger de 4 Samsung House Am Kronberger Hang 6 65824 g Schwalbach Ts Deutschland HUNGARY 06 80 SAMSUNG www NIA Samsung Electronics Magyar Rt 7267864 samsung com hu Sz pv lgyi Business Park 1037 Budapest Sz pv lgyi t 35 37 ITALIA 800 SAMSUNG www 02 Samsung Electronics Italia S p A 7267864 samsung com it 92141801 Via C Donat Cattin 5 20063 Cernusco Sul Naviglio MI WWW Samsung Electronics Benelux B V LUXEMBURG 02 261 03 710 samsung lu NA Medialaan 50 1800 VilvoordeBelgium Europe 0900 20 200 88 WWW Samsung Electronics Benelux B V NETHERLANDS 0 10 Min samsung nl N A Postbus 681 2600AR Delft Nederland WWW Samsung Electronics Nordic AB NORWAY 815 56 480 samsung com no NA SE 19427 Kanalvagen 10A Upplands Vasby Sweden WWW 48 22 Samsung Electronics Polska sp Z 0 0 POLAND 0 801 801 881 samsung com pl 607 4448 Dzia Obs ugi Klienta02 678 Warszawa ul Szturmowa 2a www SAMSUNG ELECTRONICA PORTUGUESA S A PORTUGAL 808 200 128 samsung com pt NA Rua Cesario Verde no 5 4 Piso2795 753 Queijas Por

Download Pdf Manuals

image

Related Search

Related Contents

User Guide - Suprag AG  caracteristicas eléctricas nominales de consumo  佛 山 市 顺 德 区 杰 扬 五 金 制 品 有 限  BULLETIN COMMUNAL Printemps 2012 n°46  Instructions to User  MD20B  Prismes de dedoublement Haag-Streit - HAAG-STREIT  9.食物アレルゲン検査用試薬  SilhouetteTM - Silknsilhouette.eu    

Copyright © All rights reserved.
Failed to retrieve file