Samsung SPS-210 User Manual
Contents
1. ELECTRONICS DVD Digital AMP System CE SPS 210 Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE REAR COVER NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERSONNEL IMPORTANT NOTE The mains lead on this equipment is supplied with a moulded plug incorporating a fuse The value of the fuse is indicated on the pin face of the plug If it requires replacing a fuse approved to BS1362 of the same rating must be used Never use the plug with the fuse cover omitted if the cover is detachable If a replacement fuse cover is required it must be of the same colour as the pin face of the plug Replacement covers are available from your dealer If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point you should obtain a suitable safety approved extension lead or consult your dealer for asssistance However if there is no alternative to cutting off the plug remove the fuse and then safely dispose of the plug Do not connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord IMPORTANT The wires in the mains lead are coloured in accordance with the following code BLUE NEUTRAL BROWN LIVE As these colours may not correspond with the coloured m2. Master Volume dial It is used to adjust the volumes of all six channels at the same time and to adjust the volume of each channel individually CH LEVEL button see page 13 Use this button to adjust the volume of each channel separately MODE button see page 15 Use this button to select the sound mode INPUT SEL Button see page 14 Press this button to select the desired one among the external components connected to the main unit Part Names CC Displav panel _ Dolby Digital display It is displayed when the DVD recorded in Dolby Digital is played INPUT display It shows the input selection of the external components connected to the main unit DIS display It is displayed when the DVD recorded in DTS is played OPTICAL display It shows that OPTICAL is selected for the digital input signal G MPEG display It is displayed when the DVD recorded in MPEG Multichannel is played B COAXIAL display It shows that COAXIAL is selected for the digital input signal TEST TONE display It is displayed when the speaker volumes of six channels are adjusted E ANALOG display It shows that ANALOG is selected for the digital input signal LEVEL display It is displayed when the speaker volume of each channel is adjusted D Speaker display It indicates the speakers in operation dB display It is displayed with numerals when the volume of each channel or the entire volume is adjusted B Operation
3. symbol is marked on the DVD MPEG 5 1CH MPEG is a method of compression techniques for reproducing high quality of video and audio signals for digital TV or DVD Like Dolby Digital and DTS it provides the six channel mode consisting of front L R center rear L R and subwoofer and the same frequency range MPEG I Multichannel symbol is marked on the DVD DOLBY DIGITAL 2CH DTS 2CH MPEG 2CH It is the function of integrating six channels into two channels for output so that the digital strips encoded in six channels can be made compatible with the conventional 2 channel stereo system As this unit basically supports six channels it may not be necessary to convert the input signals for 2 channel system but if the DVD to be played is encoded in 2 channels it is played in 2CH mode 15 Installation of Speaker System To achieve the optimum quality of the sound effect provided by this unit it is very important to position the speakers properly Refer to the following description for a better sound experience Standard Speaker Positions Front L R Speakers Install the speakers on the left and right side in front of the listener at the height of the listener s ears and arrange the speakers to aim at the listening position Center Speaker Install the speaker at the front center at the height of the listener s ears Surround L R Speakers Install the speakers on the left and right side in the rear of the listener at the
4. audio taper or any other related equipment or material SAMSUNG ELECTRONICS U K LTD 20
5. height of the listener s ears and arrange the speakers to aim at the listening position e If the speakers cannot be positioned at the height of the listener s ears because of the structure of the room install the speaker above the listener s ears Make sure that the speakers are placed to aim at the listening position Subwoofer Install the speaker on the floor in front of the listener Install the subwoofer on hard floor keeping a distance of at least 10cm to the wall Since there is a speaker on the left of the main unit make sure that the left side is clear of any obstruction Center Speaker ZA N FrontL Main Front R Speaker Speaker When installing the subwoofer keep a distance of at least 10cm to the wall Q a and at least 30cm to the TV o L Surround L Surround R Speaker Speaker 16 Troubleshooting No power No sound from the speaker Sound distortion Remote control not working 5 1CH not displayed and only 2CH or STEREO is played The power cord is not plugged in the AC outlet The POWER switch on the rear panel of the main unit is not set to ON The speaker cords are not connected to the speaker terminals of the main unit or to the speaker itself DVD LDP TV etc is not connected to the INPUT terminal Optical cord is stained with dirty objects MASTER VOLUME is set to the minimum Muting is activated MASTER VO
6. AEE 8 SOC A 9 Connection to External COMPONENIS rri aa aio 10 Basic Operations str script gata ts oto atin eee eee 11 Speaker SEMI un eE ae ea eade e Ea e TEE TE E EEE 12 Golmponeni SST OU ia iii rap aaea a EE AE Ea TAE EREE TAa EE AAEE EE DEENEN RE 13 Mode SelectiON ssis sinui ance a ia a 14 Notes on Dolby Digital DTS and MPEG i ia iii 15 Installation of Speaker Searle 16 Troubleshooting Pre EEA 17 Pedra 18 Rara 19 Accessories After unpacking check that the following items are contained Three 3 speaker cords for Two 2 speaker cords for surround front center speakers 5 meters each speakers 10 meters each One 1 optical cord 7 One 1 set of nonskid One 1 instruction One 1 RCA cord speaker pads manual Cautions on Installation Do not dissemble the unit Touching the inside of the unit will expose you to a risk of electric shock Be sure to disconnect the power plug from the AC outlet when installing the unit or before dissembling the unit When pulling out the power cord from the wall outlet do not hold the cord because the cord may be damaged to cause short circuiting or cut Do not touch the unit with wet hands to avoid a risk of electric shock Be careful to avoid dropping foreign objects such as pins hair or coins into the unit to avoid a risk of electric shock or fire When cleaning the unit do not use gasoline or thinner Use clean dry clothes Do not cover the air vents wi
7. D103XH100 mm l UNITED KINGDOM This Samsung product is warranted for the period of twelve 12 months from the original date of purchase against defective materials and workmanship In the event that warranty service is required you should return the product to the retailer from whom it was purchased However Samsung Authorised Dealers and Authorised Service Centres in other EC Countries will comply with the warranty on the terms issued to purchasers in the country concerned In case of difficulty details of our Authorised Service Centres are available from Samsung Electronics U K Ltd Euro Service Centre Stafford Park 12 TELFO RD Shropshire TF3 3B Tel 0870 2420303 Fax 01952 207117 M WARRANTY CONDITIONS 1 The warranty Is only valid if when warranty service is required the warranty card is fully and properly completed and is presented with the Original invoice or sales slip or confirmation and the serial number on the product has not been defaced N Samsung s obligations are limited to the repair or at its discretion replacement of the product or the defective part 3 Warranty repairs must be carried out by Authorised Samsung Dealers or Authorised Service Centres No re imbursement will be made for repairs carried out by non Samsung Dealers and any such repair work and damage to the products caused by such repair work will not be covered by this warranty 4 This product is not considered to be
8. LUME is set too high The volume of the subwoofer is set too high The distance to the main unit is too far The batteries ran out The remote sensor is exposed to direct sunlight The DVD player is not set to 5 1CH Refer to the instruction manual of the DVD player The DVD is encoded for 2 channel system Plug the power cord tightly Set the POWER switch to ON Check the connection of the speaker cords Connect to the INPUT terminal Wipe the cord with a soft cloth Adjust the MASTER VOLUME Press the MUTE button Lower the MASTER VOLUME Lower the volume of the subwoofer Use the remote control unit at a closer distance Replace the batteries Block the direct sunlight Specifications u Main Amplifier e Output at all channels driven Front L R Center Surround L R Subwoofer Digital Specifications Input sensitivity resistance Digital input impedance speakers Front L R and Surround L R Speaker Impedance Frequency range Dimensions Center Speaker Speaker Impedance Frequency range Dimensions Subwoofer Speaker Impedance Frequency range RMS Total 175 Watts 25 25W 25W 25 25W MAX Total 350 Watts 50 50W 50W 50 50W 100W 900mV 47K Ohm 230V 50Hz W252XD423XH266 mm 32 44 1 48KHz COAXIAL 0 5V 75 Ohm 100HzZ 20KHz W100XD103XH100 mm 100Hz 20KHz W247X
9. arkings identifying the terminals in your plug proceed as follows The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED WARNING DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E OR BY THE EARTH SYMBOL OR COLOURED GREEN OR GREEN AND YELLOW A DANGER This symbol is intended to alert you to the presence of dangerous voltage within the product AN CAUTION This svmbol is intended to alert vou to the presence of important instructions accompanving the product The lightning flash with an arrowhead svmbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the unit s enclosure that mav be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance servicing instructions in the literature accompanving the appliance Warning To prevent fire or shock hazard do not expose units not specificallv designed for outdoor use to rain or moisture N Attention Installation should be performed by qualified service personnel only in accordance with the National Electrical Code or applicable loca
10. defective in materials nor workmanship by reason that it requires adaptation in order to conform to national or local technical or safety standards in force in any Country other than the one for which the product was originally designed and manufactured This warranty will not cover and no re imbursement will be made for such adaptation nor any damage which may result REPUBLIC OF IRELAND 5 This warranty covers none of the following a Periodic check ups maintenance and repair or replacement of parts due to normal wear and tear b Cost relating to transport removal or installation of the product c Misuse including the falure to use this product for its normal purposes or incorrect installation d Damage caused by Lightning Water Fire Acts of God War Public Disturbances incorrect mains voltage improper ventilation or any other cause beyond the control of Samsung 6 This warranty is valid for any person who legally acquired possession of the product during the warranty period 7 The consumers statutory rights in any applicable national legislation whether against the retailer arising from the purchase contract or otherwise are not affected by this warranty Unless there is national legislation to the contrary the rights under this warranty are the consumers sole rights and Samsung its subsidiaries and distributors shall not be liable for indirect or consequential loss or any damage to records compact discs videos or
11. display It displays the functions in the current operational mode Part Names SPEAKER 49 rear DD Power switch It turns the main power source on and off Digital signal input jacks OPTICAL COAXIAL For connection with an external component having the optical or coaxial output jack Analog signal input jacks AUX1 AUX2 For connection with up to two external components having the analog output jack Speaker output jacks For connection with front L R speakers center speaker and surround L R spearkers 6 Power cord Remote Control Names DVD AMP POWER button e Angle 1 Press the button to turn on the power to the unit 2 DVD button The remote control works within the range g of 30 degrees to both sides and within the Use this button to select the DVD function ei 210 metere fon theremote Subwoofer volume control buttons sensor of the unit Use these buttons to adjust the volume of the subwoofer TONE button TEST TONE Use this button to check the connection status of each speaker INPUT button Press this button to select the desired one among the external components connected to the unit G MUTE button Press this button to turn off the audio temporarily during playback of music or movie MODE DIMMER button MODE For selection of sound field modes DIMMER For adjustment of brightness of the displays AMP volume control buttons Use these buttons to adjust the v
12. e the button is pressed 13 Mode Selection MODE Press the MODE button f The mode switches in the following order each time the button is pressed DOLBV PRO LOGIC Dolbv Pro Logic is the stereo sound effect technologv developed bv Dolbv Laboratories With the sound direction emphasis circuit it provides the experience of sound movement between front and rear and between left and right as in the theater svstem The sound direction emphasis circuit separates the signals of four channels front L R center rear to enhance to three dimensional sound depth THEATER It is the surround function of providing the effect of being immersed in the 3D sound field and the feeling of expansion as in the theater bv reproducing the reflected sound and the reverberation in harmonv STADIUM It is the surround function of reproducing the unique tone that can be experienced only in the stadium such as the reverberation and the sound delay between the stadium and the listener s ear Select this mode to feel the effect that the listener is in the stadium when watching the sports broadcasting or outdoor concert programs HALL It is the surround function of reproducing the sound effect in the concert hall by realizing the spatial resonance and the reflected sound from different directions of the ceiling and the walls in the concert hall Select this mode for enjoying the c
13. he initial setting after the system installation for adjustment of the volume of each speaker so that the volume from each speaker can be heard at the same level from the listening position depending on the layout of the room 1 Press the TEST TONE button The display for selection switches in the following order at the interval of two seconds DINT FONTI Z NT DO FRONT L e CENTER FRUNT R 2 Select the desired channel and use the MASTER VOLUME to adjust the volume between 10dB and 10dB 3 The channel switches to the next channel in three seconds after adjusting the volume of the selected channel 4 After adjusting the volume of all channels press the TEST TONE button again How to adjust the volume with CH LEVEL It is usually used during playback Adjust the volume to the listener s taste depending on the situation at the time of watching the movie or enjoying the music 1 Press the CH LEVEL button The display for selection switches in the following order each time the button is pressed Siani Se ee a SL TI ZU _ CI Ill If the mode is set to STEREO l L 2 Select the desired channel and use the MASTER VOLUME to adjust the volume 3 After adjusting the volume of all channels it is switched to the sound field mode in three seconds 12 Component Selection INPUT SEL m Press the INPUT SEL button The display shows the components for selection in the following order each tim
14. l codes Power Disconnect Units with or without ON OFF switches have power supplied to the unit whenever the power cord is inserted into the power source however the unit is operational only when the ON OFF switch is in the On position The power cord is the main power disconnect for all units gt Safety Instructions The following illustrations represent precautions The lightning bolt is a warning sign alerting you to dangerous voltage inside the product DO NOT OPEN THE DVD VCR Refer to service personnel Do NOT expose the DVD VCR to Do NOT expose the DVD VCR to Do NOT expose the DVD VCR to extreme temperature conditions direct sunlight any liquids below 5 C and above 40 C or to extreme humidity conditions less than 10 and more than 75 Do NOT place any objects on the During a storm and or lightning If the remote control is not used for a DVD VCR or remote control unplug the DVD VCR from the mains long period of time remove the socket and aerial batteries and store it in a cool dry place THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS CONTENTS Table of Contents VII 2 ACCESSO L TA 3 Cautions on Installation capii 4 Folla 4 PINI L A E E E E E 5 7 Remote Control INAS ice esien eeii eaea natin eaea vac ra AE EE EE AEEA eS aA AA ARE a E E a EEEE E
15. olume of all speakers at the same time Surround speakers volume control buttons Use these buttons to adjust the volume of both surround speakers at the same time D AMP button Press this button for selection of AMP functions TV POWER button Press this button to turn on the TV B Center speaker volume control buttons Use these buttons to adjust the volume of the center speaker System Connections Connecting the Speak To protect the speakers make connections while the power to the unit is turned off Surround R speaker Surround L speaker AMAMI Samsun Front R speaker Front L speaker Center speaker White SPEAKER Mill ea NI Di TA i H z A y g isir G oy TTN du N AA N A G DEG E a a A F y i A LEFT A ta A l Connect the speaker cord plugs to the speaker jacks of the same color Connection to External Components Be sure to turn off the power before connecting the external component to the unit OPTICAL Connect with the external ns oo components using digital signals coaxial Ex CD recorder MD DVD etc Tgr comin AUDIO OUTPUT Connect with the external components using analog signals Ex VCR TV etc 10 Basic Operations The ST BY display can be on when the POWER switch on the rear panel of the unit is set to ON INPUT SEL 2 Use the INPUT SEL Button to select the component f SOIT ea CmovVvici
16. oncert opera or orchestra to feel the effect that the listener is in the concert hall l Surround Effect by Audio Programs ns TIT l PL Speaker Configuration According to with DTS the Surround Tvpe Program marked with Dolbv ali Logic MPEG aby Protoss e pepe e stro e e neater e e e e Notes on Dolby Digital DTS and MPEG DOLBY DIGITAL 5 1CH Dolby Digital is the three dimensional sound effect technology through digital signal processing of the next generation developed by Dolby Laboratories and provides the sound completely split by six channels Six channels in Dolby Digital are called as 5 1 channel of which 5 means the front L R center and rear L R channels These five channels provide all audible frequency range of 20 20 000 Hz Meanwhile 0 1 channel means the subwoofer providing the bass range below 120 Hz LU Digital symbol is marked on the DVD DTS 5 1CH DTS is the technology developed by Digital Theater Systems Inc Like Dolby Digital it also provides the six channel mode consisting of front L R center rear L R and subwoofer and the same frequency range The difference between DTS and Dolby Digital lies in the data compression Dolby Digital has a higher compression ratio than DTS thus occupying less space in the storage media On the other hand DTS occupies larger space with a lower compression ratio but has gained a reputation that more emphasis is placed on the sound quality Idits
17. t Ci IV 1 ODI IV Z INIL LUMA MUA 1 gt MLA C 3 Operate the selected component Refer to the instruction manual of each component for detailed information of operation 4 Adjust the volume The volume may be adjusted between 1 MIN and 50 MAX When watching a movie in the dark this function is useful to prevent distraction due to the display of the main unit The brightness of the display can be selected among Bright Dim Off 1 Automatic DIMMER function After the ST BY power is turned on the display is dimmed automatically in 15 seconds 2 Manual DIMMER function Press and hold down the MODE button on the main unit or the remote control unit for 1 5 seconds repeatedly to select among the choices of brightness of the display Note x Press the MUTE button to turn off the sound instantly e The ST BY display on the main unit blinks It is convenient when you have a guest or answer the phone e To turn on the sound back press the MUTE button again 11 1 Press the POWER button to turn on the power When the power cord is plugged to the AC outlet the ST BY display is lit When the power is turned on the ST BY display is turned off Speaker Setup For convenience of checking the connection of each speaker and volume adjustment this unit contains the TEST TONE function and the CH LEVEL function TEST TONE CH LEVEL How to adjust the volume with TEST TONE It is used at t
18. th a newspaper a tablecloth a curtain etc in order not be obstruct heat radiation Do not place the exposed fire source such as a burning candle on the unit Failure to pay due attention to installation of the speakers may cause the clothes of the net frame to be torn or broken This unit is manufactured under license DTS and DTS Digital Surround are the from Dolby Laboratories Licensing registered trademarks of Digital Theater Corporation Dolby and J symbol are Systems Inc trademarks of Dolby Laboratories Licensing Corporation Features 7 e Dolby Digital function e DTS function Dolby Pro Logic function MPEG Multichannel function Various sound field modes of Theater Hall and Stadium Digital signal input function Optical Coaxial Analog signal input function AUX 1 AUX 2 Built in subwoofer High quality audio Dimmer function Part Names 9 2 8 3 7 DS 01 Front Panel Controls MUTE button Press this button to turn off the sound instantly TEST TONE button see page 13 Use this button to check the connection status of each speaker ST BY ON button Press this button to light the display lamp and to start the unit STANDBY display lamp It displays the standby status when lit Press the POWER button to turn the lamp off G Remote Sensor It receives the remote control signals for operation with the remote control unit
Download Pdf Manuals
Related Search