Samsung SM-348B User Manual
Contents
1. Technical Specifications ITEM CD RW DVD CD DISC Disc types DVD ROM DVD VIDEO DVD R DVD RW CD DA Audio supported CD ROM CD ROM XA CD Plus CD Extra in read mode Photo CD Single Multi session Video CD ready Enhanced CD CD I FMV CD R CD RW CD TEXT Erasing disc types CD RW Disc diameter 120 mm or 80 mm DRIVE Data transfer rate Recording CD R 1200 KB sec 8X 2400 KB sec 16X PERFORMANCE 3600 KB sec 24X 4800 KB sec 32X 6000 KB sec 40X 7200 KB sec 48X CD RW Ultra Speed Writing DISC 3600 KB sec 24X High Speed Writing DISC 1500 KB sec 10X 2400 KB sec 16X Low Speed Writing DISC 600 KB sec 4X Reading CD CD R CAV 48 DVD CAV 16 PIO Mode 4 16 6MB sec Multiword DMA mode 2 16 6MB sec Ultra DMA mode 2 33 3MB sec Access time 130ms 130ms 110ms Data Buffer Bulk Type 2MB Retail Pack 8MB Laser Semiconductor laser Slide mechanism Stepping motor Spindle motor Brushless motor Load mechanism Tray DC motor Soft Eject Horizontal Vertical ERRO R RATE Mode 1 1 block 10712 Mode 2 1 block 10 9 FRONT PANEL Auto eject or Auto inject If the Power is ON BUSY this means the disc is loaded Green Reading Recording Status Headphone output Stereo mini jack 3 6 mm 0 65V 20 rms 33 ohm Dial type Eject button Indicator Volume control REAR PANEL R2. The COMBO Drive provide a High Speed rewriting Disc recording function CD RW 24X To rewrite at a High speed use the disc which High Speed is printed on Ultra Speed 24X High Speed RW supporting 10X 16X General RW supporting 4X English 15 SAMSUNG DIGITal everyone s invitedm Troubleshooting Caution with errors Every CD R or CD RW drive records data by applying recording laser onto a CD If the CD is damaged or recording data is not possible you need to remove the following causes of the error before using the CD Itis recommended to set a CD R or CD RW drive as follows 1 Do not work on a multi tasking environment and remove screen savers If you work on a multi tasking environment while the CD RW drive is recording deleting data Buffer Under Run may occur Do not allow any external access to the Host PC while recording data If another user accesses your printer through a network while you are recording data errors may occur Remove the Auto Run function of the CD If you insert a CD that has the Auto Run function to a drive connected to a PC while recording deleting data this may cause errors How to cancel select the Auto Run function Cancel Select the Auto Run function in Start gt Setting gt Control Panel System gt Device Manager gt CD ROM Setting Use image files when you record many small files If you use a lot of small size files for recording this may reduce th
3. COMBO drive we strongly recommend that you check that your setup meets the system requirements listed below tem Description S Computer Intel Pentium Il 400MHz Celeron 466A or higher 64 MB of RAM or higher with an P 80pin IDE interface for Ultra DMA 4 Windows 98 2000 ME XP NT4 0 or higher For Windows NT we recommend Service Pack2 and Version is over 4 00 1381 5 0 or higher For MS DOS The CD R CD RW driver can only read a disc without MS DOS premaster Software PC with Windows 98 2000 ME XP NT4 0 DVD Video playback software and DVD Video playback appropriate hardware the Power DVD MPEG software is included in the COMBO drive package DVD Region Protection Coding RPC he RPC feature is supported on DVD players and is used with DVD video discs such as movies Currently he motionpicture industry has divided the worldinto different regions or zones thatcorrespond to the regional markets intowhich the motion picture industry releasesmovies Simply put RPC codes are placedon movies marketed throughout the world based on the region of the world inwhich they are being sold These IRPCcodes help control and prevent piratingof new movies into other motion pictureregions prior to their true releasedates within those markets he SM 348 COMBO drive supports RPCphase II In the RPC 2 mode the localcode can be changed by users RPC 2is selected by default for the SM 348 COMBO drive ou can change the region code up tofive tim
4. rear of the COMBO drive 1 5VDC 2 Ground A Cut Side 3 Ground 4 12V DC Note An improperly connected power cable may cause trouble Check the direction of the power connector and the incline side of the COMBO drive before connecting 2 Connecting the E IDE cable Insert the IDE cable 40 pin which is connected to the hard disk to the interface terminal Place the red line of the cable close to the Pin 1 When using one E IDE cable Connect the cable to the SL Slave of the Master Slave Select Terminal at the rear of the COMBO drive a Slave Drive Choose the SL Jumper Hard Drive ley MainBoard a When using two E IDE cable gt f there is only one COMBO drive select MA Master Master Drive Choose the MA Jumper Hard Drive English 10 MainBoard Primary 1 Secondly 1 SAMSUNG DIGITal everyone s invitedm Setup gt f there is two COMBO drive select MA Master SL Slave cS 5L MA i f y f t l 1 f Master Drive Choose the MA Jumper b Slave Drive Choose the SL Jumper Hard Drive MainBoard Primary 1 Secondly 1 3 Installing a jumper on the master slave select terminal a Connect a jumper to the rear side of the COMBO If the jumper is connected to MA Master it will work in the Master mode If the jumper is connected to SL Slave it will work in the Slave mode If t
5. SAMSUNG DIGITal everyone s invitedm Index Safety Precautions Nofational 2 2cheseio octet eee eel eee ee ee 3 Installation 235253 eee tes i ae eae eee a et ee E 4 WhileOpertng 2 225 22222e2 556 SoSesoeenoss eea sees 5 Other eas A a ii I a la a cal irae ed ake Installing the COMBO Drive pan Aa oe oe 9 Connecting the Cables ee ee et ete ee e 9 Installing the CD Record Utility z B z 2 2 12 Installing the Device Driver 12 Setting Up the Device Driver a ae be ae en 12 Using the Drive Using the COMBO Drive 13 Storing and Cleaning Your Discs 13 Upgrading the Firmware Flash Memory 14 System Requirements ose oe ee ee ee Troubleshooting Solving Recording Problems eee SNS 15 Caution With errors ensien E eee ee eee eee ene 16 Solving Technical Problems pe e Ha oe ve 18 Specifications English 2 SAMSUNG DIGITal everyone s invitedm Safety Precautions Notational rf Tha fodierwing ara basig pracmulions ip amsuro user safety and radece iha riak of property damage Pleade mad thie carefully and fallow ihe precaglland al l ll times for proper use of ihe device Warning Caution Warning This symbol indicates explanations abo
6. ct sunlight Avoid low or high temperature environments Avoid high humidity environments English 4 SAMSUNG DIGITal everyone s invitedm Safety Precautions While Operating Handle with caution to prevent damage from external shock Do not drop the drive and protect it fromsevere shocks It can damage the drive or cause it to malfunction Do not move the drive while in operation and do not attempt to open the disc tray byforce Make sure to close all working programs before attempting to open the tray and always usethe open close button Do not insert a pin into the emergency opening while in operation gt Do not use cracked distorted or damaged discs In particular a disc with a crack on the inner tracks may break while in use English 5 SAMSUNG DIGITal everyone s invitedm Safety Precautions Never allow food particles or foreign substances to enter the drive casing To protect against the risk of fire do ot spill such liquids as alcohol and benzene on the drive Do not disassemble attempt to repair or modify the device without express approval as directed in the manual To reduce the risk of damage electric shock and fire English 6 SAMSUNG DIGITal everyone s invitedm Introduction 1 Connector for stereo headphones with a 3 6 mm stereo mini jack 2 Headphone volume control 3 Emergency eject hole if the compartment do
7. e System icon Fi Click on the Device Manager tab 5 Expand the CD ROM branch 7 The SAMSUNG COMBO SM device name is displayed The SAMSUNG device driver enables discs in the COMBO drive to be read but not recorded in an MS DOS environment the driver is located in the D driver folder on the CD record utility disc Setting Up the Device Driver Automatic Setup The device driver is located in the Ddriver folder of the CD Record Utility disc which is provided in the package ll u Insert the CD Record Utility disc into the CD ROM drive and open the Ddriver folder Run the CDSETUP EXE file in the Ddriver folder H When Setup is successfully completed click OK button or press the Enter key Aw a Reboot the computer Manual Setup T Make the C SAMSUNG directory 2 Copy the files from the diskette to the C SAMSUNG directory To do so type COPY D Ddriver C SAMSUNG after the C prompt and press Enter J Edit the CONFIG SYS file Add the DEVICE C SAMSUNG SSCDROM SYS D SSCD000 V entry te VCE hab aan SY omnis a Edit the AUTOEXEC BAT file Add the C SAMSUNG MSCDEX D SSCD000 entry E SS a i a ee 5 Reboot the computer English 12 SAMSUNG DIGITal everyone s invitedm Using the Drive Using the COMBO Drive To play audio or video CDs and or DVDs in your COMBO drive proceed as follows 1 Push the power button and boot the computer After bootin
8. e transaction rate of the PC Although Super link function is often run the recording quality may become low If you copy a CD from another you do not require making available space in the hard disk However when you use image files you need to copy them on the hard disk first and then copy to a CD In this case you need to ensure maximum 700MB of available space in the hard disk for reliable recording process Use an E IDE cable which has the specified length 46cm Using E IDE cables longer than 46cm may cause errors during data transaction Use only one recording software program To install a software program for recording uninstall any other types or versions of recording software programs first and then reboot the computer Make sure you use the recording software CD Nero Burning Rom Roxio Easy CD Creator provided by us Using our software program with others may cause errors in recording Term Description 1 H What is Buffer Under Run Every CD R or CD RW drive records the data that the Host PC wants to record until the data flow ends However if the buffer becomes empty temporarily this may cause errors in recording data What is Auto Run If inserting a CD into a drive the operating system executes the Autorun inf file of the CD automatically What is Super link This function is to check the buffer to see if there are data while recording If the buffer is empty it waits at the address and then restarts
9. equired power 5 V 1 2 A rms 12 V 1 5 A rms Interface connector ATAPI E IDE Audio output Line out 0 7V 20 47Kohm Jumper block Molex 70203 or other compatible models OPERATING Operations Temperature 5 45 C Humidity 10 80 ENVIRONMENT Storage Temperature 25 60 C Humidity 10 90 Dimensions 148 2 W x 42 H x 184 D mm including bezel GENERAL Net weight 750 g RELIABILITY MTBF 125 000 POH Duty 20 English 19
10. es not open when you press the Eject button power off the computer insert a pin or unfolded paper clip in the hole and push firmly 4 Indicator Light 5 Eject button 6 Disc compartment the compartment opens and closes automatically when you press the Eject button D Design and specifications are subject to change without prior notice English 7 SAMSUNG DIGITal everyone s invitedm Introduction 1 Two pin digital audio output terminal for use with a sound or MPEG card supporting digital audio features 2 Four pin sound output terminal for use with a sound card refer to the sound card documentation for further details 3 Master slave select terminal 4 40pin host E IDE interface connector 5 4pin power terminal A 5V DC B 12V DC English 8 SAMSUNG DIGITal everyone s invitedm Setup Installing the COMBO Drive To install your COMBO Drive in the PC proceed as follows T Make sure that the PC is powered off and disconnected from any power source Z If necessary attach a horizontal bracket to both sides of the drive J Remove the cover from a free expansion slot and install the COMBO drive as shown in the illustration 5 S Connecting the Cables English 9 SAMSUNG DIGITal everyone s invitedm Setup 1 Connecting the power cable The 4 pin power cable from the internal power unit of your computer must be connected to the power terminal on the
11. es via an MPEG application Please contact your dealer or local SAMSUNG representative if you wish tochange the local code more than ivetimes English 14 SAMSUNG DIGITal everyone s invitedm Troubleshooting If you have any problems recording via your COMBO drive follow the appropriate instructions below for the source that you are using Hard Drive T Check whether the source file is corrupted a Optimize the hard disk by using the Windows defragmenter feature START PROGRAMS ACCESSORIES SYSTEM TOOLS DISC DEFRAGMENTER 3J Decompress the hard disk if it is compressed wi Make sure that the space available on the hard disk is at least twice the size of the largest file to be recorded on the disc 5 lf you wish to record more than 1000 small files e First create an image file and copy the image file to the disc e Choose the low record speed e Compress small files and then record them Network Drive qT Copy the network drive contents to the hard disk and then from the hard disk to the COMBO drive CD ROM Drive J Clean the source CD if necessary Create an image file and then copy the image file to the COMBO drive 4 Check the CD ROM drive record speed There are two recording methods e Low speed file by file e High speed transfer of an image file from the hard disk af If the transfer speed of the CD ROM drive is slower than the record speed reduce the record speed Note
12. g the computer open the disc compartment by pressing the Eject button 3 Insert the disc CD DVD with the label on the disc facing upwards and close the disc compartment by pressing the Eject button The indicator light comes on af Play the disc CD DVD Playing Audio CDs Run the CD player supplied with Windows or your sound card You can listen to the CD by connecting an earphone to the earphone connection terminal Playing DVDs or Video CDs Set up and run the SOFT MPEG program supplied as an accessory Storing and Cleaning Your Discs To ensure a long service life for your discs and drive follow the pre cautions below when storing and cleaning your discs 1 Donot place a disc in direct sunlight 2 Store a disc vertically in a well ventilated and stable location 3 Do not write or attach a label on a disc Do not drop a disc or place heavy objects on it 5 Do not touch the surface of a disc hold it by the edges amp To clean a disc polish lightly from the inside of the disc to the outside with a soft cotton cloth 7 Do not leave the disc compartment open when you are not using it English 13 SAMSUNG DIGITal everyone s invitedm Using the Drive Upgrading the Firmware Flash Memory The product firmware can be upgraded by downloading the updated file from the following Web site http www samsung ODD com http www samsungelectronics com odd System Requirements Before you install the
13. he jumper is connected to CS CSEL you can control the device by using the host interface signal CSEL In general connection to MA is recommended a Connecting the audio cable from a sound card Connect the 4 pin audio cable between the sound output terminal on the COMBO drive and the audio input terminal on the sound card For clearer sound use a digital output terminal Available only for the CAID that supports digital output This may not be available for general sound cards English 11 SAMSUNG DIGITal everyone s invitedm Setup Installing the CD Record Utility To record data on a CD R or CD RW disc in the COMBO drive you must first install the CD record utility For compatibility reasons you are recommended to uninstall any existing software of the same type before installing this utility 7 Insert the disc supplied with the COMBO drive in the drive g Follow the instructions displayed on the screen to install the utility Refer to the separate utility documentation for further details F Store the utility disc in a safe place Installing the Device Driver No additional device driver is needed for Windows 98 2000 ME XP NT4 0 as the default Windows device driver is used You can check that the COMBO drive has been correctly detected by Windows To do so proceed as follows T Double click on the My Computer icon on your desktop 2 Double click on the Control Panel folder a Double click on th
14. n Media Player of Windows ME XP the earphone does not appear in the Digital Mode ACD is not read or is read too slowly The disc compartment will not open Check whether the CD is of good quality and clean it if necessary Check that the power cable is correctly connected Power off and disconnect the PC Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens When the MPEG software plays a Video CD the pictures are not regular and the running speed is too slow Adjust the size of the replay screen After checking the display resolution adjust it if necessary The Disc is not in message is displayed even though a disc has been inserted The computer may not recognize the disc if you start playback too quickly after inserting the disc Open and close the disc compartment and try again Clean the disc and try again The COMBO drive is not detected after it is connected to a sound card The interface mode of the sound card is AT BUS You must therefore connect the COMBO drive to the IDE port on the PC mother board rather than to the sound card or install an E IDE compatible sound card English 18 SAMSUNG DIGITal everyone s invi tedm Specifications SAMSUNG instructions continually strives to improve its products Both the design specifications and these user are thus subject to change without notice
15. one s invitedm Troubleshooting Problem Meaning Solution The COMBO drive is not detected by the computer After installing the COMBO drive the PC gets slower Check that the power audio and IDE cables are correctly connected to the computer Change the IDE cable and reconnect it to the computer Preferably connect a second IDE cable to the COMBO drive in master mode Check the position of the jumper in the master slave select terminal The COMBO drive is not recognized by MS DOS Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site http www samsung ODD com http www samsungelectronics com odd The COMBO drive is not detected by Windows This case may occur when there is a Windows installation problem reinstall Windows No sound is heard from an audio CD Check whether the audio cable is correctly connected to the sound output terminal on the COMBO drive and the sound card CD IN terminal Check that the sound card is operational Adjust the volume control Run the CD player supplied with Windows or your sound card You can listen to the CD by connecting headphones to the appropriate connector If you have installed the appropriate player such as Microsoft Windows Media Player you can adjust the volume using the headphone volume control on the drive front panel If you select DIGITAL at CD Audio Play i
16. recording after the buffer is full You can avoid Buffer Under Run problems by applying the above mentioned principle English 16 SAMSUNG DIGITal everyone s invitedm Troubleshooting Recommended Disc Types CD R RICOH DAIYO YUDEN MITSUI FUJI SKC ACER BEALL CD RW RICOH SONY MITSUI ACER NANYA General DMA Installation Guide Windows 98 Me Important Please read the entire DMA installation guide before installing your COMBO drive About DMA Installation For stable writing performance at high speeds Installation of DMA transfer mode for E IDE ATAPI interface is strongly recommended We recommend DMA mode for fast writing DMA Setting Before you install your COMBO drive we recommend to set DMA to enabled on your PC system See the following procedure to set DMA transfer mode in windows oprerating system Windows 98 ME Click on START Select your CD R RW drive Click on Settings Click on the Properties button Check the DMA checkbox to enables DMA Click OK Restart your PC Select the System Icon Select the Device Manager panel in System Properties Expand the CD ROM icon Windows 2000 XP Select the DMA mode by selecting Start gt Setting gt Control Panel gt System gt Device Manager gt IDEATA ATAPI Controller gt Default Assistant IDE Channel Advanced Information Select Control Panel Click on the Settings tab English 17 SAMSUNG DIGITal every
17. ut extremely dangerous matters If users ignore this symbol and handle the device the wrong way serious injury or death could result Caution This symbol indicates explanations about dangerous matters If users ignore this symbol and handle the device the wrong way damage to home or property could result Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment Prohibited Do not disassemble Q Important to read and understand at all times Any change or modification not expressly approved by designated qualified personnel could void your authority to operate this device Always make sure that the disc does not have a crack before use If the disc has a crack especially around the center hole it is recommended to make a copy immediately and use the copy instead When a cracked disc is used continuously the size of the crack is likely to grow and this will eventually result in irreparable damage to the disc Important to read and understand at all times English 3 SAMSUNG DIGITal everyone s invitedm Safety Precautions UACUELLI N Place the drive on a level surface Failure to do so may cause the device to fall onto a hard surface resulting in damage or malfunction Do not place the drive in dire
Download Pdf Manuals
Related Search