Samsung GN642BFX User Manual
Contents
1. After Sales Service Department and Customer Relations page this page also explains to you where to find this information on your appliance 1 INSTALLING YOUR APPLIANCE e GAS CONNECTION e Preliminary comments If your hob is installed above an oven or if proximity to other heating elements poses a threat of overheating the connection you absolutely must insulate the cable in a rigid pipe If a hose or soft pipe in the case of butane gas is used it should not come into contact with a moving part of the cabinet nor should it pass through a location that may become blocked The gas connection must be installed in compliance with applicable regulations in the country of installation e Gas distributed by pipe natural gas For your safety you must choose from the three following connection options Connection with a rigid pipe made from copper and with screw on mechanical connectors G1 2 gas standard mark Make the connection directly to the end of the elbow fitted on the appliance Connection with a wavy metal hose stainless steel with screw on mechanical connectors compliant with NF D 36 121 standard whose service life is unlimited Fig A Connection with a reinforced rubber hose with screw on mechanical connectors compliant with the NF D 36 103 standard whose service life is 10 years Fig B yn Warning When connecting your hob s gas supply if you have to change the direction of the elbow fi2. acidic liquids such as lemon juice vinegar etc to remain in contact with the enamel To clean the hob s stainless steel use a sponge and soapy water or a commercially available special stainless steel product VN Warning It will be easier to maintain your hob if you clean it before it has completely cooled down However never clean your appliance while it is in operation Set all the gas controls to zero Tip Q It is better to clean the parts of the hob by hand rather than in the dishwasher Do not use an abrasive sponge to clean your hob Do not use steam cleaning 53 4 SPECIAL MESSAGES DIFFICULTIES e DURING OPERATION YOU OBSERVE THAT WHAT SHOULD YOU DO e Lighting the burners There is no spark when you press on the knobs or button Check the electrical connection of your appliance Check that the spark plugs are clean Check that the burners are clean and properly assembled If the hob is attached to the work top check that the mounting brackets are not deformed Check that the gaskets under the knobs are not coming out of their lodging When you press on a knob there are sparks on all of the burners simultaneously This is normal The lighting function is centralised and controls all of the burners simultaneously There are sparks but the burner burners does do not light Check that the gas inlet pipe is not pinched Check that the
3. heat release rate KW 1 45 1 45 1 50 1 45 Reduced heat release rate with safety KW 0 700 0 650 0 700 Hourly rate g h 105 104 105 Hourly rate I h 143 AUXILIARY BURNER Marking engraved on injector 50 50 63 50 Nominal heat release rate KW 0 900 0 900 0 850 0 900 Reduced heat release rate KW 0 350 0 300 0 350 Hourly rate g h 65 64 65 Hourly rate I h 81 Hos 60 cm FOUR BURNER GAS MODEL WITH DOUBLE CROWN BURNER Total heat release rate KW 8 10 8 10 8 40 8 10 Maximum flow rate g h 588 579 588 I h 800 49 2 USING YOUR APPLIANCE e DESCRIPTION OF THE TOP GN 642 Q Semi fast burner1 50 kW High speed burner 2 25 kw Auxiliary burner 0 85 kw O Double crown burner 3 8 kW Power obtained with natural gas G20 50 2 USING YOUR APPLIANCE e SWITCHING ON GAS BURNERS The burner safety measure is a metal rod located directly to the side of the flame Each burner is controlled by a tap fitted with a safety system that in the event of acciden tal flame extinction spills draughts etc quickly and automatically cuts the gas supply and prevents it from being released Each burner is supplied by a tap that is opened when you press in the knob and turn it in a counterclockwise direction The Q point corresponds to a closed tap Select the desired burner by referring to the symbols located near the knobs e g front right burner ar Your hob is fitted with a burne
4. length of the gas inlet pipe is less than two meters Check that the gas inlet pipe is open If you have gas in a cylinder or tank check that it is not empty If you have just installed the hob or changed the gas cylinder hold the knob down in maximum open position until gas arrives in the burners Check that the injector is not clogged if it is unclog it with a safety pin e f the hob has a gas safety during lighting the flames light then go out as soon as the knob is released Press firmly down on the knobs and hold them down for a few seconds after the appearance of flames Check that the parts of the burner are correctly mounted Check that the gaskets under the knobs are not coming out of their lodging Avoid strong draughts in the room Light your burner before placing your saucepan on it n reduced heat mode the burner goes out or the flames remain high Avoid strong draughts in the room Check that the gas type being used corresponds to the injectors installed Read about markings on the injectors in the Changing the Gas Supply chapter Reminder The cooking hobs are sold pre set for use with network gas natural gas Check that the burner power screws are properly set See the Changing the Gas Supply chapter The flames look irregular or uneven Check the cleanliness of the burners and injectors under the burners the assembly of the burners etc
5. you connect the power cables of any electrical appliances plugged in close to the hob ensure that they are not in contact with the cooking zones As a safety measure do not forget after use to close the general supply tap for gas distributed by pipe or the tap of the tank for butane or propane gas When a knob becomes difficult to turn Do NOT FORCE IT Request an emergency service call for the installer The CE compliance designation is affixed to these hobs This appliance must be installed in compliance with currently applicable regulations and used only in a well ventilated location Consult this guide before installing and using your appliance ENVIRONMENTAL PROTECTION The packing materials can be recycled Dispose of them in containers provided for this purpose based on their individual recycling symbols Used appliances should be disposed of in compliance with the regulations in effect in your place of residence Warning Installation should only be performed by installers and qualified technicians Before installation ensure that the condi tions of local distribution gas type and pressure and the settings of the appliance are compatible This hob complies with the EN 60335 2 6 standard with regard to the heating of cabi nets and the Class 3 standard with regard to installation according to the EN 30 1 1 standard RESPECT FOR THE ENVIRONMENT e RESPECT FOR THE ENVIRONME
6. IT MANUALE PER L INSTALLAZIONE E L UTILIZZO oV INSTALLATIONS OCH ANVANDARMANUAL EN GUIDE FOR INSTALLATION AND USE Piano di cottura GN 642 Spish ll GN 642 Cooking Hob GN 642 Lm TABLE OF CONTENTS e Safety Recommendations 39 e Environmental Protection 40 Description of Your Appliance 4d 1 INSTALLING YOUR APPLIANCE e Proper Positioning 42 e Flush Mounting 42 Tips for Flush Mounting 43 e Electrical Connection 43 e Gas Connection 44 e Changing the Gas Supply 46 2 USING YOUR APPLIANCE Description of the top 50 e Switching on gas burners ___ b51 e Cookware for gas burners _____ 52 3 DAILY CARE OF YOUR APPLIANCE e Maintaining your appliance 53 4 SPECIAL MESSAGES DIFFICULTIES e During operation 54 5 COOKING CHART e Gas cooking guide ___ __ 9 _ _ 5 6 AFTER SALES SERVICE DEPARTMENT AND CUSTOMER RELATIONS e After Sales Service 56 38 SAFETY RECOMMENDATIONS e SAFETY RECOMMENDATIONS We have designed this cooking hob for use by private persons in their homes All cooking should take place under your surveillance These cooking hobs are meant to be used exclusively for cooking beverages and foodstuffs and do not contain any asbestos based materials As part of our commitment to constantly improving our products we reserve the right
7. NT This appliance s packaging material is recy clable Help recycle it and protect the envi ronment by dropping it off in the municipal receptacles provided for this purpose Your appliance also contains a great amount of recyclable materi al It is marked with this label to indicate the used appliances that should not be mixed with other waste This way the appliance m recycling organised by your manu facturer will be done under the best possible conditions in compliance with European Directive 2002 96 EC on Waste Electrical and Electronic Equipment Contact your town hall or your retailer for the used appliance collec tion points closest to your home We thank you doing your part to protect the environment 40 SAFETY RECOMMENDATIONS e DESCRIPTION OF YOUR HOB Saucepan support Q Burner covers Q Thermocouple Q Gasket Q Burner head Q Injector Q Tap Q Spark plugs Q Knob Tip 9 This Guide to Installation and Use is valid for several models Minor differences in details and fittings may emerge between your appliance and the descriptions provided 41 1 INSTALLING YOUR APPLIANCE PROPER POSITIONING Your appliance shoud be built in the surface of a support cabinet that is a minimum of 3 cm thick made of a material that resists heat or that is covered with such a material So as not to disturb movement of cooking utensils there should not be to the right or left or back any obstacle wi
8. arning Exceeding this limit may damage the product Reposition the burner heads burner covers and pan supports on the hob a 7 Each time you change the gas supply tick the box corresponding to the new gas level on the label found in the plastic bag Refer to the corresponding Gas Connection section B Wrench 5 Crucible Injector 1 INSTALLING YOUR APPLIANCE Adjust the hob connections they are located underneath the knobs Fig 04 Proceed one tap at a time Remove the knobs and the gaskets by pulling them up Switching from natural gas to butane propane With a small flat head screwdriver screw in all the way the brass yellow burner power screws Fig 05 in a clockwise direction Replace the gaskets and the knobs paying careful attention to their direction and ensuring that the Knobs are pushed in all the way Switching from butane propane to natural Unscrew the brass yellow burner power screws Fig 05 using a small flat head screwdriver by turning two times counterclockwise Replace the knob Light the burner in maximum heat mode then turn down to reduced heat mode Remove the knob again then turn the burner power screws clockwise until it reaches the lowest possible setting that does not extinguish the flame j Anm Replace the gasket and knob 2 Tap axis Make several attempts to shift from the ZEE maximum flow rate to the minimum th
9. e During cooking the knobs become hot Use small saucepans on the burners located closest to the knobs Larger saucepans should be placed on the largest burners those that are furthest from the knobs Properly place the saucepan in the centre of the burner 54 5 COOKING CHART e GAS COOKING GUIDE PREPARATIONS TIMES DOUBLE FAST SEMI AUXILIARY CROWN FAST SOUPS Bouillons 8 10 minutes X Thick soups X FISH Court bouillon 8 10 minutes X Barbecue 8 10 minutes SAUCES Hollandaise b arnaise X X B chamel aurore 10 minutes X X VEGETABLES Endives spinach X Cooked peas 25 30 minutes X Provencal tomatoes 15 20 minutes X Golden brown potatoes X Pasta X MEATS Steak X Blanquette Osso bucco 90 minutes Sauteed poultry breasts 10 12 minutes Tournedos 10 minutes X FRYING French fries X Beignets X DESSERTS Rice pudding 25 minutes X X Fruit compote xX Cr pes 3 4 minutes X Chocolate 3 4 minutes X Cr me anglaise 10 minutes X Coffee small percolator X 55 6 AFTER SALES SERVICE san LECTRONICS E Per qualsiasi domanda o commento sui prodotti SAMSUNG rivol gersi al centro post vendita SAMSUNG 9964 0621 09 06 Translatp Agency TECHNICIS 800 31 42 78 www samsung com it Kontakta kundtjanst pa SAMSUNG Om du har nagra fragor eller kommentarer som har att g ra med produkter fran SAMSUNG 08 585 367 87 www samsung com se EN If you have any question
10. e a maximum length of two meters and must be accessible along their entire length They must be replaced before the end of their service life indicated on the pipe Regardless of the means of connection chosen ensure that the connection is air tight after installation with soapy water 1 INSTALLING YOUR APPLIANCE e CHANGING THE GAS SUPPLY VN Warning Your appliance is sold pre set for natural gas The injectors required for adaption to butane propane can be found in the plastic bag containing this guide Each time you change the gas supply you must complete the following Adapt the gas connection Change the injectors Adjust the hob connections Adapt the gas connection Refer to the Gas Connection section Change the injectors proceeding as follows Remove the pan supports heads and covers from all burners Using the wrench provided unscrew the injectors located under each crucible and remove them Fig 07 Replace with the corresponding gas injectors in compliance with the placement of the injectors and the table of gas properties at the end of this section to do this First screw them in manually until the injector locks into place Apply the wrench to the injector as far as it will go Draw a line on the burner plate using a pencil at the place indicated Fig 02 Turn the wrench clockwise until the line appears on the other side Fig 03 VN W
11. e flame should not go out if it does unscrew the burner power screw so as to obtain good flame retention during these position switches Burner power adjustment screw 47 1 INSTALLING YOUR APPLIANCE e Markings on the injectors MARKINGS ON THE INJECTORS The adjacent table shows where the injectors are positioned on your appliance according to the type of gas Each number is marked on the injector used Injector marking 94 Four burner gas model with double crown burner Natural Gas Butane Propane Gas AE a TO 038 See Description of the Top chapter 48 1 INSTALLING YOUR APPLIANCE e Gas Properties IT IT IT SE SE GB GB GB Applicance intended to be installed in Butane Propane Natural Butane gas GB JF anc tee cat IIZH3 G30 G31 G20 G30 DE m ER cat IIZH3 B P P8 30 mbar 37 mbar 20 mbar 30 mbar Hourly rate below At 15 C under 1013 mbar HIGH SPEED BURNER Marking engraved on injector 78 78 121 78 Nominal heat release rate KW 2 25 2 25 2 25 2 25 Reduced heat release rate KW 0 850 0 850 0 850 Hourly rate g h 164 161 164 Hourly rate I h 214 DOUBLE CROWN BURNER Marking engraved on injector 95 95 147 95 Nominal heat release rate kW 3 50 3 50 3 80 3 50 Reduced heat release rate with safety KW 1 450 1 400 1 450 Hourly rate g h 254 250 254 Hourly rate I h 362 SEMI FAST BURNER Marking engraved on inector 62 62 94 62 Nominal
12. r lighting sys tem built into the knobs To light a burner press on the knob and turn it in a counterclockwise direction to the maximum setting A Continue to press on the knob to produce a series of sparks until the burner lights The setting for more moderate flame intensi ties are between the symbol and the symbol OK In order to ensure the proper lighting of the double crown burner we suggest that you light it before placing cookware on it When a knob becomes difficult to turn do not force it Request an emergency service call from the installer Warning Hold the knob completely pressed down for a few seconds after the flame appears to trigger the safety system 51 2 USING YOUR APPLIANCE COOKWARE FOR GAS BURNERS Which burner should you use depending on your cookware Diameter of the cookware Burner Use 20 to 30 cm Double crown 16 to 28 cm High speed Searing foods Semi fast Sauces Reheating 12 to 24 cm Auxiliary Gentle simmer yn Warning Adjust the ring of flames so that they do not extend beyond the edges of the cookware Fig 01 Do not use cookware with a concave or convex bottom Fig 02 Do not use cookware that partially covers the knobs Fig 03 Do not leave a gas burner operating with empty cookware CONCAVE 2 fe Keep natural ventilation orifices in your home open or install a mechanical
13. s or comments relating to SAMSUNG products please contact the SAMSUNG customer care centre 0870 242 0303 www samsung com uk Brandt Appliances a simplified joint stock company with a capital of 10 000 000 euros Nanterre Trade and Companies Register no 440 302 347 GN642 9964 0621 09 06 56
14. thin 30 cm of the hob If a horizontal divider wall is positioned under the hob it should be placed between 10 cm and 15 cm away from the top of the work top In any event do not store aerosol cans or containers under pressure in any compartment that may exist under the hob See Safety Recommendations chapter FLUSH MOUNTING Follow the diagram Fig 07 Remove the pan supports the burner covers and burner heads noting their positions Turn the hob over and carefully place it on top of the opening in the cabinet so as not to damage the knobs and spark plugs APPLIANCE Width Depth Thickness Total 58cm 522cm 49cm dimensions above the work top Total 55 4cm 474cm 3 5 cm dimensions below the work toptravail To ensure a tight seal between the housing and the work top glue the foam seal along the exterior edge of the housing before installing the hob Fig 02 1 INSTALLING YOUR APPLIANCE e TIPS FOR FLUSH MOUNTING e ELECTRICAL CONNECTION Underside view of the housing Fig 02 D uu brackets Place your hob in the opening of the support cabinet carefully pulling the table toward you Reposition the burner heads burner covers and pan supports on the hob Connect your hob to the gas supply See Gas Connection chapter and to the power supply See Electrical Connection chapter If you wish you can immobilise the hob using the four mo
15. to make changes to them based on technological advances to their technical functional and or esthetic properties Using a gas cooking appliance results in the generation of heat and humidity in the location where it is installed Please ensure that your kitchen has proper ventilation keep natural ventilation orifices open or install a mechanical device mechanical ventilation hood Intensive prolonged use of the appliance may require additional ventilation you can for example open a window or provide more effective ventilation by increasing power to the mechanical ventilation if you have it Do not store CLEANING products or FLAMMABLE products aerosol cans or containers under pressure as well as papers cookbooks etc in the cabinet underneath your cooking hob If you use a drawer located under the hob we recommend that you avoid storing in it items that are heat sensitive plastic papers aerosol cans etc The conditions for adjusting the hob are written on a sticker located in the plastic bag as well as on the packaging n order to easily locate the reference information for your appliance we recommend that you note them on the After Sales Service Department and Customer Relations page This page also explains to you where to find this information on your appliance Your hob should be disconnected from power and fuel supplies electricity and gas before any repairs When
16. tted on the appliance Change the gasket Screw on the elbow s nut careful not to exceed a torque of 17 N m 44 1 INSTALLING YOUR APPLIANCE e Gas supplied by tank or cylinder butane propane For your safety you must choose from the three following connection options Connection with a rigid pipe made from copper and with screw on mechanical connectors G1 2 gas standard mark Make the connection directly to the end of the elbow fitted on the appliance Connection with a wavy metal hose stainless steel with screw on mechanical connectors compliant with NF D 36 125 standard whose service life is unlimited Fig O1 Connection with a reinforced rubber hose with screw on mechanical connectors compliant with the XP D 36 112 standard whose service life is 10 years Fig 02 In an existing system a soft pipe fitted with clamps whose service compliant with the XP D 36 110 standard whose service life is five years may be used It is necessary in this case to use an adaptor without forgetting to fit a sealing washer between the adaptor and the hob s bent Fig 03 fal 7 You can obtain the adaptor and the sealer washer from your After Sales Service Department Warning Screw on the adaptor with a torque not to exceed 25 N m Q Sealing washer Q Adaptor not supplied Q Clamp not provided Warning All soft pipes and hoses whose service life is limited must hav
17. unting brackets delivered with a screw Fig 02 to attach them to the four corners of the housing You must use the holes provided for this purpose according to the diagram above Fig 07 Stop screwing when the mounting bracket starts to become deformed Do not use a screwdriver Your hob is sold with a power cable type HO5V2V2F T90 cross section 1 mm with three conductors phase ground neutral After sales service reference 77X3767 6470 1516 It must be connected to a 220 240V monophase grid via a standardised CEI 60083 electrical outlet with phase ground neutral or or an all pole cut off device with a minimum distance between contact openings of 3 5 mm The plug of the electrical outlet must be accessible after installation CABLE CROSS SECTION TO BE USED 220 240 V 50 Hz 3 conductors HO5V2V2F T90 including one cable ground wire Cross section of 1 conductors in mm Fuse 10A VN Warning The safety wire green yellow is connected to the appliance s ground terminal and must be connected to the ground lead ofthe electrical set up The fuse in your set up must be 10 amperes If the power cable is damaged it must be replaced by a cable or a special kit available from the manufacturer or its After Sales Service Department at 7 n order to easily locate the reference information for your appliance we recommend that you note them on the
18. ventilation device mechanical ventilation hood Intensive prolonged use of the appliance may require additional ventilation you can for example open a window or provide more effective ventilation or increase power to the mechanical ventilation if you have it a minimum air flow of 2 m per kW of gas power is required Example 60 cm Four gas burners Total power 1 5 2 25 3 8 0 85 8 4kW 8 4 kW x 2 16 8 m h minimum flow 52 3 DAILY CARE OF YOUR APPLIANCE e MAINTAINING YOUR APPLIANCE MAINTENANCE WHAT TO DO PRODUCTS ACCESSORIES TO USE Of the spark plugs In the event that the spark plugs become Small hard bristled brush and injectors soiled clean them using a small hard Safety pin bristled brush non metallic The gas injector is located in the centre of the burner in the shape of a dish Be careful not to obstruct it during cleaning as this will undermine the performance of your hob In the event of obstruction use a safety pin to unclog the injector Of the pan If tough stains occur use a non abrasive Gentle scrubbing cream supports and gas cream then rinse with clean water Disinfectant sponge burners Carefully wipe each part of the burner before using your hob again Of the enamel or To clean the hob s enamel use a Gentle scrubbing cream stainless steel scrubbing cream Polish it with a dry Commercially available cloth specialised product Do not allow
Download Pdf Manuals
Related Search