Home

Samsung LD220ZLapfit Touch User Manual

1. Avoid placing burning candles mosquito repellent or cigarettes on the product and installing the product near a heater e Otherwise it may result in fire Avoid installing the product in a badly ventilated location such as inside a bookshelf or closet e Otherwise it may result in fire due to internal over heating Keep the plastic bags used to pack the product away from children e If children place the plastic bags over their heads they may suffocate Avoid installing the product in a location exposed to dust moisture sauna oil smoke or water rain drops and installing it within a vehicle e This may result in electric shock or fire Avoid installing the product at an easily reachable height where children may reach it e fa child touches the product the product may fall and this may result in injury e Since the front part is heavier install the product on a flat and stable surface Make sure to use only the power cord supplied by our company In addition do not use the power cord of another electric appliance e Otherwise it may result in electric shock or fire Connect the power plug to a wall outlet that can be easily reached e When a problem occurs with the product you must unplug the power plug to cut the power off completely You cannot cut the power off completely using only the power button on the product Ask an installation engineer or relevant compan
2. Cinema mode 7 k m PICTURE Ma g icColor COLOR SIZE amp POSITION Color Tone SETUP amp RESET Color Effect INFORMATION Gamma Using the product 3 6 MENU DESCRIPTION MagicColor Expresses natural colors more clearly without changing the picture quality using proprietary digital picture quality improvement technology developed by Samsung Electronics e lt Off gt Turns the MagicColor function off e Demo You can compare the pictures processed by MagicColor with the original pictures e lt Full gt Provides a clearer picture including areas corresponding to skin color e Intelligent Improves the chroma of pictures except for areas corresponding to skin color Supported when lt MagicAngle gt is set to lt Off gt and Color Effects is set to lt Off gt Red You can adjust the red color value of pictures according to your preference e This menu is unavailable when lt MagicColor gt is set to lt Full gt mode or lt Intelligent gt mode e Only supported when lt Color Effect gt is set to lt Off gt Green You can adjust the green color value of pictures according to your preference e This menu is unavailable when lt MagicColor gt is set to lt Full gt mode or lt Intelligent gt mode e Only supported when lt Color Effect gt is set to lt Off gt Blue You can adjust the blue color value of pictures according to your preference This men
3. SyncMaster LD220Z LCD Monitor User Manual The color and the appearance may differ depending on the product and the specifications are subject to change without prior notice to improve the performance Table Of Contents MAJOR SAFETY PRECAUTIONS BGClIOle YOU Stall sec di Cm NG ee aed ee ew ee TO AA KAN 1 1 Custody and Maintenance 0 0 0 cee es 1 2 Safety Precautions 660 AB AA NN eee eee ewe eee PAA KENA 1 3 INSTALLING THE PRODUCT Package Contents 2 cee es 2 1 Connecting witha PG 4 0 cc tad eee KARA eta eee Bee NG re ee 2 2 Using the Touchscreen naaa Ak ewe GMA ede AKA whe ees 2 3 Connecting an External Device Using the HDMI Cable 2 4 Connecting an USB cable 2 ccc es 2 5 Connecting Headphones 0 00 cece ees 2 6 Kensington Lock ORE TERA ede bt eae 2 7 USING THE PRODUCT Setting the Optimal Resolution 0 00 eee es 3 1 Standard Signal Mode Table 00 0 eee 3 2 Installing the Device Driver 0 000 eee ee 3 3 Installing the USB Driver an 3 4 Product Operating Buttons 00 cee 3 5 Using the Screen Adjustment Menu OSD On Screen Display 3 6 INSTALLING THE SOFTWARE NatUilal GOO 4 046 ca cake ecaeeeeans AA 4 1 Magic TUNG paasa ha nawa da es Pewee ee eee cee eee eee 4 2 MUMISCICON cccradue sate c eaten tedaede heen en Meee oe ees 4 3 TROUBLESHOOTING Monitor Self Diagnosis 00 cece ee 5 1
4. Before Requesting Service eee ee 5 2 KAPA ve teres viride Cheese deter eo eee ee 5 3 MORE INFORMATION Specifications 6 60 55566 664505556 008040 400600650 s ORO OTE 6 1 Power Saving Function ss etcces cee te eee deseo ANA NG ees 6 2 Contact SAMSUNG WORLDWIDE 0 00 es 6 3 Correct Disposal of This Product Waste Electrical 4 Electronic Equipment Europe only 6 4 1 Major Safety Precautions 1 1 Before You Start Icons used in this manual ICON NAME MEANING GB Caution Indicates cases where the function may not work or the setting may be canceled Note Indicates a hint or tip to operate a function Using this Manual e Make yourself fully aware of the safety precautions before using this product e Ifa problem occurs refer to the troubleshooting section Copyright Notice The contents of this manual are subject to change without prior notice for performance improvement Copyright 2009 Samsung Electronics Co Ltd All Rights Reserved The copyright of this manual is reserved by Samsung Electronics Co Ltd The contents of this manual may not be partially or in whole reproduced distributed or used in any form without the written permission of Samsung Electronics Co Ltd The SAMSUNG logo and SyncMaster are the registered trademarks of Samsung Electronics Co Ltd Microsoft Windows and Windows NT are the registered trademarks of Microsoft Corporation
5. 4 1 Natural Color What is Natural Color This software works only for Samsung products and enables adjusting the displayed colors on the product and matches the colors on the product with the colors of the printed pictures For more information refer to the online help of the software F1 The Natural Color is provided online You can download it from the website below and install http www samsung com us consumer learningresources monitor naturalcolorexpert pop download htmil 4 1 Installing the Software 4 2 MagicTune What is MagicTune MagicTune MagicTune is a software program that helps with monitor adjustments by providing comprehensive descriptions of monitor functions and easy to understand guidelines Users can adjust the product with the mouse and the keyboard without using the operating buttons of the product Installing the Software 1 Insert the installation CD into the CD ROM drive 2 Select the MagicTune setup program If the pop up screen for the software installation does not appear on the main screen find and double click the MagicTune setup file on the CD ROM 3 Select the installation language and click Next 4 Complete the remaining software installation steps according to the instructions displayed on the screen e The software may not work properly if you do not restart the computer after the installation e The MagicTune icon may not appear depending on the computer system and th
6. Avoid using a damaged power cord or plug or a Avoid connecting multiple electric appliances to loose power outlet a single wall outlet e Otherwise it may result in electric shock or 3 e Otherwise it may result in fire due to fire O overheating of the wall outlet Avoid plugging in or unplugging the power Plug the power plug in firmly supply with wet hands a NN e Otherwise it may result in fire e Otherwise it may result in electric shock o Make sure to connect the power cord to a Avoid bending or twisting the power cord grounded wall outlet for insulation class 1 excessively and avoid placing heavy objects on equipment only the cord e Otherwise it may result in electric shock or e Otherwise it may result in electric shock or injury fire due to a damaged power cord Keep the power cord and the product away from a heater If the pins of the power plug or the wall outlet are covered in dust clean it using a dry cloth Nail e Otherwise it may result in electric shock or O fire e Otherwise it may result in fire Major Safety Precautions 1 3 A Caution Avoid unplugging the power plug while the product is operating e Otherwise it may damage the product due to electric shock When unplugging the power plug from the wall outlet make sure to hold it by the plug and not by the cord e Otherwise it may result in electric shock or fire Installation Related A Warning
7. OSD or to return to a higher level OSD menu OSD Adjustment Lock This function locks the OSD in order to maintain the current settings or to prevent the settings from being changed by another person On If you press and hold the MENU button down for 5 seconds the OSD Adjust ment Lock function is activated Off If you press and hold the MENU button down for 5 seconds again the OSD Adjustment Lock function is disabled Even if the OSD Adjustment Lock function is activated users can adjust the brightness and contrast and can set up the adjustment function assigned to the m Users can set the Customized Key to one of the following functions If the user presses the Customized Key m after setting it the configured function will be performed e lt PC gt mode lt MagicBright gt lt MagicAngle gt lt MagicEco gt sImage Size e lt AV gt mode lt Picture Mode lt MagicAngle gt lt MagicEco gt sImage Size gt You can set the function of the Customized Key by selecting lt SETUP amp RESET gt gt lt Customized Key in the OSD A V Use these buttons to navigate the menu or to adjust a value in the OSD When OSD is not on the screen push the button to adjust volume 3 5 Using the product DESCRIPTION ICON Use this button to select a function If you press the C button when there is no OSD the input signal Analog amp me HDMI is switched When the i
8. depending on the product When installing the product with a stand 10cm 393 naa About persistent images e Displaying a still image for a long time may create a persistent image or stain on the screen If you do not use the product for a long time set the power saving mode or screen saver e Due to technological constraints of the LCD Panel manufacturer the images generated by this product may appear either brighter or darker than normal by appr 1ppm parts per million pixel The number of sub pixels of an LCD panel by size The number of Sub Pixels Max Horizontal Resolution x Max Vertical Resolution x 3 Example If the maximum resolution is 1920 x 1080 the number of sub pixels is 1920 x 1080 x 3 6 220 800 1 2 Major Safety Precautions 1 3 Safety Precautions Icons used for safety precautions ICON NAME MEANING Wanin Failing to follow the precautions marked with this sign may result in a serious injury or A 9 even a fatality Caution Failing to follow the precautions marked with this sign may result in a personal injury or A property damage Meaning of Signs SO Do not perform ap Q Do not disassemble Q Do not touch amp Must be followed The power plug must be unplugged from the wall outlet Must be grounded to prevent electric shock Power Related The following images are for your reference and may differ depending on models and countries A Warning
9. not be mixed with other commercial wastes for disposal More Information 6 4 6 4 More Information
10. upgrade for MagicTune please visit our website 4 2 Installing the Software 4 3 MultiScreen What is MultiScreen im MultiScreen MultiScreen enables users to use the monitor by partitioning multiple sections Installing the Software 1 Insert the installation CD into the CD ROM drive 2 Select the MultiScreen setup program amp If the pop up screen for the software installation does not appear on the main screen find and double click the MultiScreen setup file on the CD ROM 3 When the Installation Wizard appears click Next 4 Complete the remaining software installation steps according to the instructions displayed on the screen The software may not work properly if you do not restart the computer after the installation e The MultiScreen icon may not appear depending on the computer system and the product specifications e If the shortcut icon does not appear press the F5 key Restrictions and Problems with the Installation MultiScreen The MultiScreen installation may be affected by the graphics card motherboard and the networking environment Operating System OS e Windows 2000 e Windows XP Home Edition e Windows XP Professional e Windows Vista e Windows 7 eg For MultiScreen the operating systems Windows 2000 or later is recommended Hardware e Atleast 32MB of memory e At least 60MB of free space on the hard disk drive Removing the Software Click Start select Setting
11. 726 7864 http www samsung com sg THAILAND 1800 29 3232 02 689 3232 http www samsung com th TAIWAN 0800 329 999 http www samsung com tw VIETNAM 1 800 588 889 http www samsung com vn MIDDLE EAST amp AFRICA SOUTH AFRICA 0860 SAMSUNG 726 7864 http www samsung com za TURKEY 444 77 11 http www samsung com tr U A E 800 SAMSUNG 726 7864 http www samsung com ae 8000 4726 6 3 More Information 6 4 Correct Disposal of This Product Waste Electrical amp Electronic Equipment Europe only Applicable in the European Union and other European countries with separate collection systems X This marking on the product accessories or literature indicates that the product and its electronic accessories e g kA charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please sepa rate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of mate rial resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should
12. 78 http www samsung com es SWEDEN 0771 726 7864 SAMSUNG http www samsung com se SWITZERLAND 0848 SAMSUNG 7267864 CHF 0 08 http www samsung com ch min U K 0845 SAMSUNG 7267864 http www samsung com uk CIS BELARUS 810 800 500 55 500 ESTONIA 800 7267 http www samsung com ee LATVIA 8000 7267 http www samsung com lv LITHUANIA 8 800 77777 http www samsung con lt MOLDOVA 00 800 500 55 500 KAZAKHSTAN 8 10 800 500 55 500 http www samsung com kz ru KYRGYZSTAN 00 800 500 55 500 RUSSIA 8 800 555 55 55 http www samsung ru TADJIKISTAN 8 10 800 500 55 500 UKRAINE 8 800 502 0000 http www samsung com ua http www samsung com ua ru UZBEKISTAN 8 10 800 500 55 500 http www samsung com kz ru ASIA PACIFIC AUSTRALIA 1300 362 603 http www samsung com au CHINA 400 810 5858 http www samsung com cn 010 6475 1880 HONG KONG 3698 4698 http www samsung com hk http www samsung com hk en INDIA 3030 8282 http www samsung convin 1 800 3000 8282 1800 110011 INDONESIA 0800 112 8888 http www samsung comvid JAPAN 0120 327 527 http www samsung com jp More Information 6 3 ASIA PACIFIC MALAYSIA 1800 88 9999 http www samsung com my NEW ZEALAND 0800 SAMSUNG 0800 726 786 http www samsung com nz PHILIPPINES 1 800 10 SAMSUNG 726 7864 http www samsung com ph 1 800 3 SAMSUNG 726 7864 1 800 8 SAMSUNG 726 7864 02 5805777 SINGAPORE 1800 SAMSUNG
13. 8 watts Less than 0 8 watts Less than 0 8 watts Power Consumption With USB Cable 43 watts Less than 2 3 watts Less than 2 3 watts If there is no power cut off switch the power consumption is O only when the power cord is disconnected More Information 6 2 6 3 Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center NORTH AMERICA U S A 1 800 SAMSUNG 726 7864 http www samsung com us CANADA 1 800 SAMSUNG 726 7864 http www samsung com ca MEXICO 01 800 SAMSUNG 726 7864 http www samsung com mx LATIN AMERICA ARGENTINA 0800 333 3733 http www samsung com ar BRAZIL 0800 124 421 http www samsung com br 4004 0000 CHILE 800 SAMSUNG 726 7864 http www samsung com cl COLOMBIA 01 8000112112 http www samsung com co COSTA RICA 0 800 507 7267 http www samsung com latin ECUADOR 1 800 10 7267 http www samsung com latin EL SALVADOR 800 6225 http www samsung com latin GUATEMALA 1 800 299 0013 http www samsung com latin HONDURAS 800 7919267 http www samsung com latin JAMAICA 1 800 234 7267 http www samsung com latin NICARAGUA 00 1800 507 7267 http www samsung com latin PANAMA 800 7267 http www samsung com latin PUERTO RICO 1 800 682 3180 http www samsung com latin REP DOMINICA TRINIDAD amp TOBAGO 1 800 751 2676 1 800 SAMSUNG 726 7864 http www sams
14. B IN port of the product to the D Sub port on your PC using the D Sub cable e When the graphics card provides DVI Digital output e Connect the HDMI IN port of the product to the DVI port on your PC using the HDMI to DVI cable HDMI IN e GNH e When the graphics card provides HDMI output e Connect the HDMI IN port of the product to the HDMI port on your PC using the HDMI cable HDMI IN 2 Connect one end of the power cord to the DC Adapter and plug the other end into a dedicated 220V or 110V wall outlet 2 2 Installing the Product The input voltage is switched automatically When the product is connected to a PC you can turn the product on and use it When both the HDMI and D Sub lt Analog gt cables are connected you can select the input signal lt Analog HDMI gt by pressing the OO button Installing the Product 2 2 2 3 Using the Touchscreen To use the touch screen function connect both the D Sub or HDMI or HDMI DVI cable and USB cable install the touch screen driver and set the touch screen monitor as default monitor Connect the product to a PC depending on the video output supported by the PC e When the graphics card provides D Sub Analog output e Connect the RGB IN port of the product to the D Sub port on your PC using the D Sub cable e Connect the port of the product to the USB port on your PC using the D Sub cable e Wh
15. HDMI connector USB 1up 2down Head Phone Dimensions WxHxD Weight Simple stand 517 0 X 353 0 X 84 0 mm 20 4 X 13 9 X 3 3 inch 5 5 kg 12 1 Ibs Tilt 10 30 5 Environmental considerations Operating Operating Temperature 50 F 104 F 10 C 40 C Humidity 10 80 non condensing Storage Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 95 non condensing Class B Information Communication equipment for residential use This device has been registered regarding EMI for home use Class B It may be used in all areas Class B equipment emits less electromagnetic waves than Class A equipment 6 1 More Information 6 2 Power Saving Function This product provides a power saving function that automatically turns the screen off when the product is not used for a predetermined period of time to reduce power consumption If the product enters power saving mode the power LED turns to a different color to indicate that the product is in power saving mode When the product is in power saving mode the power is not turned off and you can turn the screen on again by pressing any key or clicking the mouse However the power saving function only works when the product is connected to a computer that provides the power saving function STATE NORMAL POWER SAVING POWER OFF OPERATION MODE SWITCH Power Indicator On Blinking Off Without USB Cable 3
16. PICTURE _ PICTURE COLOR SIZE amp POSITION SETUP amp RESET INFORMATION Brightness Contrast Sharpness MagicBright MagicAngla Coarsa Fine lt PC signals PICTURE COLOR SIZE amp POSITION Brightness Contrast sharpness Picture Mode MagicAngle SETUP amp RESET INFORMATION lt AV signals gt MENU DESCRIPTION Brightness Controls the screen brightness This menu is unavailable when lt MagicBright gt is set to lt Dynamic Contrast gt mode e Only Supported when lt MagicEco gt is set to lt Power Saving off gt Contrast Controls the contrast of the pictures displayed on the screen a e This menu is unavailable when lt MagicBright gt is set to lt Dynamic Contrast gt or lt Cinema gt mode e This menu is unavailable when lt MagicColor gt is set to lt Full gt mode or lt Intelligent gt mode e Only supported when lt Color Effect is set to lt Off gt 3 6 Using the product MENU DESCRIPTION Sharpness Controls the clarity of details of pictures displayed on the screen This menu is unavailable when lt MagicBright gt is set to lt Dynamic Contrast gt or lt Cinema gt mode e This menu is unavailable when lt MagicColor gt is set to lt Full gt mode or lt Intelligent gt mode e Only supported when lt Color Effect gt is set to lt Off gt MagicBright Provides preset picture settings optimized for various user environment
17. VESA DPM and DDC are the registered trademarks of the Video Electronics Standard Association The ENERGY STAR logo is the registered trademark of the U S Environmental Protection Agency All other trademarks mentioned herein belong to their respective companies Major Safety Precautions 1 2 Custody and Maintenance External Surface and Screen Maintenance Clean the product with a soft dry cloth e Do not clean the product with an inflammable substance such as benzene or thinner or with a wet cloth This may result in a problem with the product e Do not scratch the screen with your fingernails or a sharp object This may result in scratches or damage to the product e Do not clean the product directly by spraying water onto the product If water enters the product it may result in fire electric shock or a problem with the product e A white stain may be generated on the surface of the high glossy model due to the inherent characteristics of the material if a Supersonic humidifier is used The appearance and the color may differ depending on the model Securing the Installation Space e Keep the required distances between the product and other objects e g walls to ensure proper ventilation Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature Install the product so the required distances shown in the figure are kept e9 The appearance may differ
18. ain in accordance with the new graph ics card driver WHEN I LOOK AT THE EXTERIOR EDGES OF THE PRODUCT SMALL ALIEN SUBSTANCES APPEAR ON IT Since this product is designed so that the color has a soft appearance by coating it with a transparent material over the black edges such things may be seen This is not a defect of the product A BEEP BEEP SOUND IS HEARD WHEN BOOTING THE COMPUTER If the beep sound is generated 3 or more times when booting up the computer please request service for the computer 5 2 Troubleshooting 5 3 FAQ FAQ PLEASE TRY THE FOLLOWING How can change the frequency of the video signal You have to change the frequency of the graphics card For more information refer to the User Manual of the com puter or the graphics card How can change the resolution Windows XP Change the resolution by selecting Control Panel Appearance and Themes Display Settings Windows Vista Change the resolution by selecting Control Panel Appearance and Personalization Personalization Resolution Windows 7 Change the resolution by selecting Control Panel Personalization Display Adjust resolution For more information refer to the User Manual of the com puter or the graphics card How can use the power saving function Windows XP Configure it by selecting Control Panel Ap
19. als e lt 4 3 gt Displays pictures at the 4 3 aspect ratio e lt 16 9 gt Displays pictures at the 16 9 aspect ratio e lt Screen Fit If a 720P 1080i or 1080P signal is input in HDMI input mode the picture is displayed as is without truncation This can only be set when the external input is connected through HDMI and lt PC AV Mode is set to lt AV gt You can adjust the horizontal position of the OSD Menu V Position You can adjust the vertical position of the OSD Using the product 3 6 5 SETUP amp RESET Reset languageMenu COLOR MagicReturn SIZE amp POSITION Magick co Off Timar On Off SETUP amp RESET f INFORMATION Customized Key MENU DESCRIPTION Reset Use this function to restore the visual quality and color settings to the factory defaults e lt No gt lt Yes gt Language Select a language for the OSD English Deutsch Espanol Fran ais Italiano Svenska Pycckun Portugu s T rk e Polski Magyar The selected language is only applied to the product OSD This setting does not affect the other functions of the PC Only works in Windows 7 and recommended when using multiple monitors e lt Off gt When lt Off gt is selected the lt MagicReturn gt function is turned off e sOn5 When lt On gt is selected the lt MagicReturn gt function is turned on e This function does not support Analog mode e This function is not support
20. ay cause dust accumulation use the power saving mode or set the and result in fire caused by overheating or screensaver to the moving picture mode short circuit or result in an electric shock Set the appropriate resolution and frequency for the product Avoid turning the product upside down or move the product holding only the stand e Otherwise it may result in eye strain e This may cause the product to fall resulting in damage to the product or injury Watching the product from too close a distance continuously may damage your eyesight Avoid using a humidifier or cooker near the product e Otherwise it may result in electric shock or fire It is important to give your eyes some rest 5 minutes every hour when viewing the product screen for long periods of time Since the display panel is hot after using it for a long time do not touch the product e This will alleviate any eye strain Major Safety Precautions 1 3 Keep small accessories away from the children Take care when adjusting the angle of the product or the height of the stand GE e If your hand or finger is caught you may be injured e f the product is tilted excessively the product may fall and this may result in injury Avoid placing a heavy object over the product o e Otherwise it may result in a problem with the product or injury Maintaining the Correct Posture when Using this Product Maintain th
21. coming off Use a soft damp cloth with a monitor exclusive cleansing agent and wipe the jet product with it w Y a e f no monitor exclusive cleansing agent is available dilute a cleansing agent with water at a ratio of 1 10 before cleaning the product Usage Related A Warning ya Since a high voltage runs through the product never disassemble repair or modify the product yourself e Otherwise it may result in fire or electric shock e If the product needs to be fixed contact a service center If the product generates a strange noise a burning smell or smoke unplug the power plug immediately and contact a service cen ter e Otherwise it may result in electric shock or fire If you drop the product or the case is dam aged turn the power off and unplug the power cord Contact a service center e Otherwise it may result in fire or electric shock When thunder or lighting occurs unplug the power cord and under no circumstance touch the antenna cable as this is dangerous e Otherwise it may result in electric shock or fire When cleaning the product disconnect the power cord and clean the product with a soft dry cloth e Avoid using chemicals such as wax benzene alcohol thinner mosquito repellent fragrance lubrication or cleansing agent when cleaning the product This may result in the exterior being deformed or the print being removed Since the exterio
22. e correct posture when using this product e Straighten your back e Keep a distance of 45 50 cm from your eyes to the screen Look down at the screen and face the screen forwards e Maintain the correct posture when using this product e Adjust the angle of the product so that light is not reflected onto the screen e Keep your elbow at a right angle and keep your arm level with the back of your hand e Keep your elbow at a right angle e Place your heels flat on the ground while keeping your knees at an angle of 90 degrees or higher and maintain the position of your arm so that your arm is below your heart 1 3 Major Safety Precautions 2 Installing the Product 2 1 Package Contents e Unpack the product and check if all of the following contents have been included e Store the packaging box in case you need to move the Product at a later stage Monitor CONTENTS Installation Manual Product Warranty User Manual D Sub Cable Power Cord USB Cable Cleaning Cloth Stylus pen OPTIONAL PARTS HDMI Cable HDMI to DVI Cable The cleaning cloth is supplied with black high glossy models only Installing the Product 2 2 Connecting with a PC The connecting part may differ depending on the product model 1 Connect the product to a PC depending on the video output supported by the PC e When the graphics card provides D Sub Analog output e Connect the RG
23. e product If the signal from the PC is one of the following standard signal modes the screen is set automatically However if the signal from the PC is not one of the following signal modes a blank screen may be displayed or only the Power LED may be turned on Therefore configure it as follows referring to the User Manual of the graphics card HORIZONTAL VERTICAL SYNC POLARITY H DISPLAY MODE FREQUENCY KHZ FREQUENCY HZ PIXEL CLOCK MHZ V VESA 640 x 480 31 469 59 940 25 175 VESA 800 x 600 35 156 96 250 36 000 VESA 800 x 600 37 879 60 317 40 000 VESA 1024 x 768 48 363 60 004 65 000 VESA 1280 x 800 49 702 59 810 83 500 VESA 1280 x 960 60 000 60 000 108 000 VESA 1280 x 1024 63 981 60 020 108 000 VESA 1440 x 900 55 935 59 887 106 500 VESA 1600 x 1200 75 000 60 000 162 000 VESA 1680 x 1050 65 290 59 954 146 250 VESA 1920 x 1080 67 500 60 000 148 500 FfF Horizontal Frequency The time taken to scan one line from the left most position to the right most position on the screen is called the horizontal cycle and the reciprocal of the horizontal cycle is called the horizontal frequency The horizontal frequency is represented in kHZ Vertical Frequency A panel must display the same picture on the screen tens of times every second so that humans can see the picture This frequency is called the vertical frequency The vertical frequency i
24. e product specifications e If the shortcut icon does not appear press the F5 key Restrictions and Problems with the Installation MagicTune The installation of MagicTune may be affected by the graphics card motherboard and the networking environment System Requirements OS e Windows 2000 e Windows XP Home Edition e Windows XP Professional e Windows Vista e Windows 7 g For MagicTune Windows 2000 or later is recommended e Programs for Windows Vista and Windows 7 are provided on our website Hardware e Atleast 32MB of memory e At least 60MB of free space on the hard disk drive es For more information refer to the website Removing the Software You can only remove MagicTune through Add or Remove Programs in Windows To remove MagicTune complete the following steps 1 Click Start select Settings and select Control Panel from the menu For Windows XP click Start and select Control Panel from the menu Installing the Software 4 2 Pak wn Double click the Add or Remove Programs icon in the Control Panel In the Add Remove window find and select MagicTune so that it is highlighted Click Change or Remove Programs to remove the software Select Yes to start removing MagicTune Wait until a message box appears informing you that the software has been removed completely For technical support the FAQ frequently asked questions or information about the software
25. ed when lt PC AV Mode is set to lt AV gt l e This function is not available in Windows2000 XP Vista system It is suggested to select MagicReturn lt Off gt e When the lt Check Signal Cable OSD is shown user can keep pressing the W Key for 5 seconds then lt MagicReturn gt is set to lt Off gt automatically e Some graphics cards do not support this function e The lt Magic Return function may not work properly with graphics cards that are not fully compliant with DVI specifications If this is the case please contact the appropriate graphics card manufacturer or set the lt Magic Return gt function to lt Off gt This function provides user a low power mode which is realized by lowering the controlling current of the display panel e lt 100 gt When lt 100 gt is selected the power consumption is 100 of Default Setting MagicEco e s7565 When lt 75 gt is selected the power consumption is 75 15 of Default Setting e 250965 When lt 50 gt is selected the power consumption is 50 15 of Default Setting e Power Saving Off gt When lt Power Saving Off gt is selected the function is turned Off This menu is unavailable when lt MagicBright gt is set to lt Dynamic Contrast gt mode Off Timer On Off You can turn the Off Timer on or off e lt Off gt lt On gt Off Timer Setting Turns the power off automatically when the configured time is reached When lt On gt of lt Off Timer On Off gt is s
26. elected This function is available only 3 6 Using the product MENU DESCRIPTION Customized Key You can set the function of the Customized Key to one of the following e lt PC gt mode lt MagicBright gt lt MagicAngle gt lt MagicEco gt sImage Size e lt AV gt mode lt Picture Mode lt MagicAngle gt lt MagicEco gt sImage Size Auto Source e lt Auto gt The monitor automatically selects an input signal e Manual Users have to manually select an input signal PC AV Mode Set to PC when connected to a PC Set to AV when connected to an AV device This function does not support Analog mode Display Time The OSD automatically disappears if no action is taken by the user You can determine the time to wait before the OSD is hidden e lt 5 sec gt s10 sec lt 20 sec s200 sect Menu Transparency You can select the transparency of the OSD e lt Off gt lt On gt LED On Off Turns the Menu button LED on or off e lt Off gt Turns the Power button LED lamp off e lt QOn gt Turns the Power button LED lamp on LED Brightness Adjusts the brightness of the Menu button LED in levels C INFORMATION PICTURE COLOR Analog SIZE amp POSITION 99 9kKHz GOHzZ NP SETUP amp RESET INFORMATION MENU DESCRIPTION INFORMATION Shows the current frequency and resolution settings Using the product 3 6 4 Installing the Software
27. en the graphics card provides HDMI output e Connect the HDMI IN port of the product to the HDMI port on your PC using the HDMI cable e Connect the port of the product to the USB port on your PC using the D Sub cable HDMI IN e When the graphics card provides DVI Digital output e Connect the HDMI IN port of the product to the DVI port on your PC using the HDMI to DVI cable 2 3 Installing the Product e Connect the port of the product to the USB port on your PC using the D Sub cable If you connect the USB port sound will be outputted from the speaker on the back of the monitor e If the driver is not installed the touchscreen function will not work e The multi touch function only works in a Windows 7 environment It does not operate in a Windows XP or Vista e With innovative highly sensitive touchscreen technology you don t need to use much force when touching the screen e Touching the screen with a rough stick or metal object can scratch it Ensure you use a dedicated stylus e Any foreign substance such as dust or moisture on the screen can cause a touchscreen malfunction Please wipe the screen and the screen s frame with a soft cloth as often as possible e In order to prevent breakage avoid applying excessive force to the screen e Connect or remove a USB device following the safe installation and removal instructions recommended by Microsoft If there is any problem wi
28. g direction TIN 2 Connect the Kensington lock cable 3 Tie the Kensington lock cable to a desk or heavy object You can purchase the locking device from an electronics store an online shop or our service center Installing the Product 2 7 3 Using the product 3 1 Setting the Optimal Resolution If you turn the power on after purchasing the product a message regarding the optimal resolution setting appears on the screen Select a language and the optimal resolution A V You can select a language with these buttons MENU If you press this button the message disappears e The message appears up to 3 times if the resolution has not been set to the optimal resolution e To set the resolution to the optimal resolution e When the PC is turned off connect the product and the PC and turn the power on e Right click over the Desktop and select Properties from the pop up menu e In the Settings tab set the resolution to the optimal resolution e The steps above may vary depending on the Windows OS 3 1 Using the product 3 2 Standard Signal Mode Table The LCD monitor has one optimal resolution for the best visual quality depending on the screen size due to the inherent characteristics of the panel unlike for a CDT monitor Therefore the visual quality will be degraded if the optimal resolution is not set for the panel size It is recommended setting the resolution to the optimal resolution of th
29. his also provides a sharp image lt Movie gt Select this mode when the surroundings are dark This will save power and reduce eye fatigue lt Custom gt Select this mode when you want to adjust the image according to your preferences e This can only be set when the external input is connected through HDMI and lt PC AV Mode is set to lt AV gt e Supported when lt MagicColor gt is set to lt Off gt and lt MagicEco gt is set to lt PowerSaving off gt Using the product 3 6 MENU DESCRIPTION MagicAngle Coarse Fine This feature allows you to see optimal screen quality according to your viewing position When viewing the screen at an angle from below above or the side of the monitor by setting the appropriate mode for each position you can obtain a similar picture quality as viewing the screen directly from the front Set to lt Off gt when viewing directly in front of the screen lt Off gt Select when viewing from the front position e Lean Back Mode1 gt Select when viewing from a slightly lower position e Lean Back Mode2 gt Select when viewing from the lower position e lt Standing Mode Select when viewing from the upper position lt Side Mode gt Select when viewing from the left or right position e lt Custom gt When lt Custom gt is selected settings for lt Lean Back Mode 17 is applied by default Users can set suitable picture quality a
30. lfunction or injury e Make sure to use a cabinet or shelf suitable to the size of the product If the product is installed in a location where the operating conditions vary considerably a serious quality problem may occur due to the surrounding environment In this case install the product only after consulting one of our service engineers about the matter e Places exposed to microscopic dust chemicals too high or low temperature high humidity such as airports or stations where the product is continuously used for a long time and so on Cleaning Related Since using a surfactant which contains a large amount of alcohol solvent or other strong chemicals may result A in the discoloration or cracking of the product exterior or the panel surface coming off be sure to use the recom mended cleansing agent only You can purchase the recommended cleansing agent from a service center fi Before cleaning the product unplug the power When cleaning the product do not spray water cord directly over the product parts Ae 2 e Otherwise it may result in electric shock or e Make sure that water does not enter the LI fire product e Otherwise it may result in fire electric shock or a problem with the product Major Safety Precautions 1 3 A Caution Avoid spraying cleansing agent directly onto the product e This may result in discoloration or cracking of the exterior of the product or the panel
31. manual THE DISPLAY AREA SUDDENLY MOVES TO AN EDGE OR TO THE CENTER Did you change the graphics card or the driver Please press the AUTO button to run the auto adjustment function Did you change the resolution and frequency appropriate to the product Set the resolution and the frequency to the appropriate values in the graphics card refer to the Standard Signal Mode Table Is the graphics card configured correctly Set up the graphics card referring to the user manual THE PICTURES ARE OUT OF FOCUS Did you change the resolution and the frequency appropriate to the product Set the resolution and the frequency to the appropriate values in the graphics card refer to the Standard Signal Mode Table Troubleshooting 5 2 THE COLOR IS DISPLAYED IN 16 BIT 16 COLORS THE COLOR HAS BEEN CHANGED AFTER CHANGING THE GRAPHICS CARD Did you install the device driver for the product Windows XP Set the color again by selecting Control Panel Display Settings Windows Vista Change the color settings by selecting Con trol Panel Appearance and Personalization Personalization Resolution Windows 7 Change the color settings by selecting Control Panel Personalization Display Change dis play settings Advanced settings Monitor Is the graphics card configured correctly Configure the color ag
32. n of the product Is the Not Optimum Mode message displayed on the screen This occurs when the signal from the graphics card exceeds the maximum resolution or the maximum frequency of the product In this case set up the appropriate resolution and the fre quency for the product Is a blank screen displayed and does the power LED blink at a 1 second interval This occurs when the power saving function is running If you click the mouse or press any key the screen will be turned on THE IMAGE IS TOO LIGHT OR TOO DARK Adjust the Brightness and Contrast Refer to the lt Brightness gt lt Contrast gt The display brightness can differ according to the mode set for lt MagicAngle gt If lt MagicBright gt is set to lt Dynamic Contrast gt the display brightness can differ according to the input signal THE ON SCREEN ADJUSTMENT MENU OSD DOES NOT APPEAR Did you cancel the screen adjustment Check if the lt OSD Adjustment Lock gt function is set to Off THE COLOR IS WEIRD THE PICTURE IS DISPLAYED IN BLACK AND WHITE Is the entire screen displayed in the same color as if viewing the screen through a cellophane paper Check the cable connection to the computer Reinsert the graphics card into the computer completely Check if the lt Color Effect gt is set to lt Off gt Is the graphics card configured correctly Set up the graphics card referring to the user
33. nput signal is switched by pressing C button or the product is turned on a message displaying the selected input signal appears at the top left of the screen Press AUTO button to adjust the screen settings automatically O AUTO This function is only available in Analog mode If the resolution settings are changed in the Display Properties the AUTO adjust ment function is performed Press this button to turn the product on or off Power LED This LED is turned on when the product works normally ie 7 O For more information on the power saving function refer to the power saving function in More Information When not using the product for a long time unplugging the power cord is recommended to minimize power consumption Speaker Using the product 3 5 3 6 Using the Screen Adjustment Menu OSD On Screen Display The Screen Adjustment Menu OSD On Screen Display Structure TOP MENUS SUB MENUS Brightness Contrast Sharpness MagicBright Picture Mode m PICTURE MagicAngle Coarse Fine HDMI Black Level MagicColor Red Green Blue Color Tone tr COLOR Color Effect Gamma SIZE amp POSITION H Position V Position Image Size Menu H Position Menu V Position Reset Language MagicReturn MagicEco Off Timer On Off Off Timer Setting Customized Key Auto Source PC AV Mode Display Time 7 SETUP amp RESET Menu Transpar LED On Off LED Bright ency ness L INFORMATION Cj
34. o lt Off gt Gamma Using this menu you can change the intensity of the colors of medium brightness e lt Mode1 gt lt Mode2 gt lt Mode3 gt Only supported when lt Color Effects is set to lt Off gt 3 6 Using the product SIZE 8 POSITION PICTURE H Position V Position COLOR image Size SIZE amp POSITION Menu H Position Menu V Position SETUP amp RESET INFORMATION MENU DESCRIPTION H Position Moves the position of the display area on the screen horizontally e This function is only available in Analog mode e Becomes enabled if the HDMI signal is received while the lt PC AV Mode is set to lt AV gt and the image size is set to lt Screen fit gt V Position Moves the position of the display area on the screen vertically e This function is only available in Analog mode e Becomes enabled if the HDMI signal is received while the lt PC AV Mode is set to lt AV gt and the image size is set to lt Screen fit gt Image Size Analog signals Menu H Position e lt Auto gt The picture is displayed at the aspect ratio of the input signal e lt Wide gt The picture is displayed in full screen regardless of the aspect ratio of the input signal e A signal not in the standard mode table is not supported e If the resolution is set to the optimal resolution the aspect ratio does not change whether the sImage Size is set to lt Auto gt or lt Wide gt HDMI sign
35. o block the vent by a table cloth or curtain e Otherwise it may result in fire due to internal overheating Avoid placing a liquid container such as a vase flowerpot beverage cosmetics or drugs ora metal object over the product e lf water or an alien substance enters the product turn the power off unplug the power cord and contact a service center e Otherwise it may result in a problem with the product electric shock or fire When a gas leak occurs do not touch the product or the power plug and ventilate immediately e A spark may result in an explosion or fire e During a thunder or lighting storm do not touch the power cord or antenna cable Avoid using or placing inflammable spray or objects near the product e This may result in an explosion or fire Avoid inserting metal objects such as a chopsticks coins or hairpins or inflammable objects into the product the vents ports etc e lf water or an alien substance enters the product turn the power off unplug the power cord and contact a service center e Otherwise it may result in a problem with the product electric shock or fire A Caution Displaying a still image for a long time may create a persistent image or stain on the ay screen When not using the product for a long time such as leaving your home unplug the power cord from the wall outlet e o If you do not use the product for a long time e Otherwise it m
36. pearance and Themes Display Screen Saver Set ting or configure it in the BIOS Setup of the computer Windows Vista Change settings by selecting Control Panel Appearance and Personalization Personalization Screen Saver You can also use the BIOS SETUP menu on the PC Windows 7 Change settings by selecting Control Panel Personalization Screen Saver You can also use the BIOS SETUP menu on the PC For more information refer to the User Manual of the com puter or the graphics card Troubleshooting 5 3 6 More Information 6 1 Specifications MODEL NAME LD220Z LCD Panel Size 21 5 inches 54 cm Display area 476 64 mm H x 268 11mm V Pixel Pitch 0 24825 mm H x 0 24825 mm V Synchronization Horizontal 30 81 kHz Vertical 56 60 Hz Display Color 16 7 M Resolution Optimum resolution 1920 X 1080 60 Hz Maximum resolution 1920 X 1080 60 Hz Input Signal Terminated D Sub HDMI Speaker Out Head Phone Out 0 7 Vp p 25 Separate H V sync Composite TTL Level V high 2 2 0 V V low lt 0 8 V Maximum Pixel Clock 164 MHz Analog HDMI Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Less than 30Ap p at AC 120V or 50Ap p at AC 220V Signal Cable 15pin D sub Connector
37. r of the product is easily scratched be sure to use a proper cleansing cloth Use the cleansing cloth with a small amount of water However if the cloth is contaminated by alien substances it may result in scratches to the exterior therefore shake off any alien substances from the cloth before using it When cleaning the product do not spray water directly over the product parts e Make sure that water does not enter the product e Otherwise it may result in fire electric shock or a problem with the product Avoid letting children to hang or climb onto the product e Otherwise it may result in the product falling and this may result in injury or death Avoid placing objects such as toys and cookies on top of the product e Ifa child hangs over the product to grab an object the object or the product may fall and this may result in injury or even death Avoid dropping an object over the product or cause impact to the product e Otherwise it may result in electric shock or fire 1 3 Major Safety Precautions Avoid moving the product by pulling the power cord or antenna cable e Otherwise it may result in electric shock fire or a problem with the product due to damage to the cable Avoid lifting up or move the product by holding only the power cord or signal cable e Otherwise it may result in electric shock fire or a problem with the product due to damage to the cable Take care not t
38. s Control Panel and then double click Add or Remove Programs Select MultiScreen from the program list and click the Add Delete button Installing the Software 4 3 5 Troubleshooting 5 1 Monitor Self Diagnosis e You can check if the product is working properly using the Self Diagnosis function e Ifa blank screen is displayed and the Power LED blinks even if the product and the PC are properly connected perform the self diagnosis function according to the procedures below Turn the product and the PC off Separate the D Sub cable from the product Turn the product on pm a PO si If the product is working properly the Check Signal Cable message appears In this case if a blank screen is displayed again make sure that there is no problem with the PC and the connection The product is working properly 5 1 Troubleshooting 5 2 Before Requesting Service Please check the following before requesting After Sales service If the problem continues please contact your nearest Samsung Electronics Service Center A BLANK SCREEN APPEARS CANNOT TURN THE PRODUCT ON Is the power cord connected properly Is the Check Signal Cable message displayed on the screen Check the connection status of the power cord Check the cable connecting the PC and the product If the message appears on the screen even if the cable is properly connected recheck the input signal by pressing the 0 butto
39. s needed This menu is unavailable when lt MagicBright gt is set to lt Dynamic Contrast gt or lt Cinema gt mode e Supported when lt MagicAngle gt is set to lt Off gt and lt Color Effect gt is set to lt Off gt Removes vertical noise lines line pattern from the screen The location of the screen may be changed after the adjustment In this case move the screen so that the screen is displayed at the center of the display panel using the lt H Position gt menu This function is only available in Analog mode Removes horizontal noise lines line pattern from the screen If you cannot remove the noise completely with the lt Fine gt function adjust the lt Coarse gt and then use the lt Fine gt function again This function is only available in Analog mode HDMI Black Level When a DVD or set top box is connected to your TV via lt HDMI gt it may cause a degradation in the screen quality such as an increase in the black level a low contrast or discoloration etc depending on the external device connected In this case adjust the screen quality of your TV by configuring the lt HDMI Black Level gt e lt Normal gt e lt Low gt The lt HDMI Black Level function is only enabled when the external device is connected via HDMI and the input signal is HDMI AV 3 6 Using the product Ki COLOR This is unavailable when lt MagicBright gt is set to Dynamic Contrast and
40. s represented in Hz Using the product 3 2 3 3 Installing the Device Driver If you install the device driver you can set up the appropriate resolution and frequency for the product The device driver is included on the CD ROM supplied with the product If the supplied drive file is corrupted please visit a service center or Samsung Electronics website http www samsung com and download the driver Insert the driver installation CD ROM into the CD ROM drive Click on Windows Driver Complete the remaining installation steps according to the instructions displayed on the screen Poe YS Select the model of your product from the model list MM SAMSUNG monitor installer Select the display adapter on which you wart to inlell te monitor 5 Check if the appropriate resolution and screen refresh rate are displayed in the Control Panel settings For more information refer to the document about the Windows operating system 3 3 Using the product 3 4 Installing the USB Driver To use the touch screen monitor the USB driver must be installed The device driver is included on the CD ROM supplied with the product If the supplied drive file is corrupted please visit a service center or Samsung Electronics website http www samsung com and download the driver 1 Connect the monitor to your PC using the USB cable 2 Insert the driver installation CD ROM into the CD ROM drive 3 Click on Touchscreen Dri
41. s such as editing a document surfing the Internet playing games watching sports or movies and so on a lt Custom gt If the preset picture modes are not sufficient users can configure the lt brightness gt and lt Contrast gt directly using this mode lt Standard gt This mode provides the picture setting appropriate for editing a document and surfing the Internet text picture lt Game gt This mode provides the picture setting appropriate for playing games that include lots of graphics and that require a fast screen refresh rate lt Cinema gt This mode provides brightness and sharpness settings similar to those of a TV for the best entertainment environment movie DVD etc lt Dynamic Contrast gt Controls the picture contrast automatically so that bright and dark pictures are balanced overall Supported when lt MagicAngle gt is set to lt Off gt and lt MagicEco gt is set to lt PowerSaving off gt Picture Mode The Monitor has four automatic picture settings lt Dynamic gt lt Standard gt lt Movie gt and lt Custom gt that are preset at the factory You can activate either lt Dynamic gt lt Standard gt lt Movie gt or lt Cus tom gt You can select lt Custom gt which automatically recalls your personalized picture settings a lt Dynamic gt Select this mode to view a sharper image than in Standard mode lt Standard gt Select this mode when the surroundings are bright T
42. th the touch screen function or sound output after a USB device is connected reconnect the USB cable or change the connection port Installing the Product 2 3 2 4 Connecting an External Device Using the HDMI Cable Connect the HDMI output port of your digital output device to the HDMI IN port of the product using the HDMI cable HDMI IN gt When all the connections are complete you can turn on and use the product and your DVD player or digital output device Press the o button and select lt HDMI gt as an input signal 2 4 Installing the Product 2 5 Connecting an USB cable Connect to the ee ports on the monitor and the USB device Installing the Product 2 5 2 6 Connecting Headphones Connect your headphones to the Headphone connection terminal Sound is only supported when the HDMI or USB port is connected 2 6 Installing the Product 2 7 Kensington Lock A Kensington Lock is an anti theft device that enables users to lock the product so that they can safely use it in public locations Since the shape and usage of the locking device may differ depending on the model and the manufacturer for more information refer to the User Manual supplied with the locking device You have to purchase an additional locking device Locking the product 1 Insert the locking part of the locking device into the hole of the Kensington lock of the product O and turn it in the lockin
43. u is unavailable when lt MagicColor gt is set to lt Full gt mode or lt Intelligent gt mode e Only supported when lt Color Effect gt is set to lt Off gt Color Tone You can set the color temperature according to your preference e lt Cool gt Sets the color temperature of the screen to a cooler color e lt Normal gt Sets the color temperature of the screen to the standard color temperature e lt Warm gt Sets the color temperature of the screen to a warmer color e lt Custom gt Select this menu to set the color temperature manually If you do not like the preset color temperatures you can manually adjust the colors of lt Color Effect gt This menu is unavailable when lt MagicColor gt is set to lt Full gt mode or lt Intelligent gt mode e Supported when lt MagicAngle gt is set to lt Off gt and lt Color Effect gt is set to lt Off gt Color Effect You can change the overall atmosphere by changing the color of pictures This menu is unavailable when lt MagicColor gt is set to lt Full gt mode or lt Intelligent gt mode e lt Off gt Turns the color effect function off e lt Grayscale gt Displays pictures in black and white e lt Green gt Displays pictures in green mono color e lt Aqua gt Displays pictures in aqua mono color e lt Sepia gt Displays pictures in sepia mono color Supported when lt MagicAngle gt is set to lt Off gt and lt MagicColor gt is set t
44. ung com latin http www samsung com latin VENEZUELA 0 800 100 5303 http www samsung com latin EUROPE AUSTRIA 0810 SAMSUNG 7267864 0 07 min http www samsung com at BELGIUM 02 201 2418 http www samsung com be Dutch CZECH REPUBLIC 800 SAMSUNG 800 726786 http www samsung com be fr French http www samsung com cz Distributor pro eskou republiku samsung tt ceska organiza n slo ka Dasis Florenc bokolovska3541 7 16000 Praha o DENMARK 8 SAMSUNG 7267864 http www samsung com dk EIRE 0818 717 100 http www samsung com ie FINLAND 30 6227 515 http www samsung com fi FRANCE 01 4863 0000 http www samsung comi fr GERMANY 01805 SAMSUNG 7267864 0 14 http www samsung de Min 6 3 More Information EUROPE HUNGARY 06 80 SAMSUNG 726 7864 http www samsung com hu ITALIA 800 SAMSUNG 726 7864 http www samsung convit LUXEMBURG 02 261 03 710 http www samsung com lu NETHERLANDS 0900 SAMSUNG 0900 7267864 E http www samsung com nl 0 10 Min NORWAY 3 SAMSUNG 7267864 http www samsung com no POLAND 0 801 1SAMSUNG 172678 http www samsung com pl 022 607 93 33 PORTUGAL 808 20 SAMSUNG 7267864 http www samsung com pt SLOVAKIA 0800 SAMSUNG 726 7864 http www samsung com sk SPAIN 902 1 SAMSUNG 902 172 6
45. ver The driver installation will start automatically Double click on the file in the Touchscreen Driver folder ii 1950 Minimal Setup Installing Execute CO WDOCUME 17H A E Wlocalsei Temp tins 1950 minim 4 Complete the remaining installation steps according to the instructions displayed on the screen 5 After installation is complete select Computer Management gt Device Manager gt Human Interface Device to check if the driver has been installed successfully m Computer Management Fie Action View Window Help ada Computer Management Local E A5T MCAFEEZ i System Tools P Computer ga Event viewer Sue Disk drives Shared Folders a Display adapters E Local Users and Groups DYDICDO ROM drives i H Floppy disk controllers Mg Human InterFace Devices H Removable Storage Disk Defragmenter fea Disk Management 2a Keyboards ES Services and Applications Chai Mice and other pointing devices FB Network adapters FH ck Other devices ae Processors Sound video and game controllers ng System devices Universal Serial Bus controllers Using the product 3 4 3 5 Product Operating Buttons Product Operating Buttons Touch one of the operating buttons lightly The LED buttons appear ICON DESCRIPTION O MENU Press this button to view the On Screen Display OSD This button is also used to exit the
46. y to install the product onto the wall e Otherwise it may result in injury e Make sure to use the specified wall mount Keep a distance of at least 10 cm from the wall when installing the product for ventilation e Otherwise it may result in fire due to internal over heating Avoid installing the product in a location that is unstable or exposed to excessive vibrations such as on an unstable or slanted shelf e The product may fall and this may result in damage to the product or injury e Ifyou use the product in a location exposed to excessive vibrations it may result in a problem with the product or fire Avoid installing the product in a location exposed to direct sunlight and installing the product near a heat source such as a fire or heater e This may shorten the product life cycle or cause fire 1 3 Major Safety Precautions A Caution Do not let the product drop while moving it Do not place the product face down on the an floor e This may result in a problem with the product or injury e This may damage the panel of the product When installing the product on a console or When putting the product down handle it ty shelf make sure that the front of the product gently does not protrude out of the console or shelf o l l U 3f pa e Otherwise it may result in a problem with O e Otherwise this may cause the productto the product or injury fall off and result in a ma

Samsung LD220ZLapfit Touch User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents