Samsung SC08F60JT User Manual (Windows 7)
Contents
1. button again The UV brush which is inserted into the hose handle not directly connected to the telescopic CAUTION pipe is dedicated for bedclothes operating the cleaner _11 USING THE DUST SENSOR Option Dust Sensor Operations e Indicates the amount of sucked in dust so that users can experience the successful operation of the product while cleaning the room tr a Red When the amount of hin sucked in dust is large Green When the amount of sucked in dust is small e The dust sensor is automatically turned on when the cleaner runs and turned off when the cleaner is stopped e Since the dust sensor runs on battery power there is no separate switch Installing the Batteries 2 Check the polarities e f the dust sensor doesn t work even after cleaning the sensor replace the batteries with new ones AAA type batteries are required e Do not disassemble or recharge the used batteries CAUTION Do not heat the batteries or put them in a fire e Check the polarities before inserting the batteries e Put the used batteries into the battery recycle bin e When you are not using the product for an extended period of time remove the batteries 12_ operating the cleaner Cleaning the dust sensor Option e Since the dust sensor consists of sensitive electronic devices if water or other liquids enters the sensor it may cause a problem e f you use the dust sensor without closing the b2. Pull out the dusting brush to use the crevice tool maintain tools and filter 15 dala ANV STOOL NIVLNIVW 0 CLEANING THE DUST SENSOR Option If the green light is not lit while cleaning e Check if the hose extension pipe or the air inlet is clogged and clean it if necessary e Empty the dust bin of the cleaner or clean the filters If the red light does not light up when cleaning a dusty location e Clean the sensors 2EA in the dust sensor block with a dry cloth Take care when you clean the sensors in the dust sensor block so that the sensors are not CAUTION damaged MAINTAIN FLOOR TOOLS Super turbine brush Option e For improved pickup of pet hair and fibre on carpets e Frequent vacuuming of hair or pet fur may cause a falling off of the rotation due to matters tangled around the drum In this case clean the drum with care Click the lever to the arrow direction as shown figure1 and open the cover Remove dust inside the brush housing using a dry duster or crevice tool Remove waste matter such as dust and hair tangled around the brushbar using scissors Click the lever to the arrow direction as shown figure4 and close the cover ee a Please be careful not to damage the brush CAUTION 16_ maintain tools and filter 2 Step Brush Carpet Cleaning Floor Cleaning e Adjust the inlet lever according to the floor surface e Remove waste matt
3. SC21F60 SERIES SCO8F60 SERIES Before operating this unit please read the instructions carefully English For indoor use only imagine the possibilities Thank you for purchasing a Samsung product To receive a more complete service please register your product at www samsung com register a safety information SAFETY INFORMATION e Before operating the appliance please read this manual thoroughly and retain it for your WARNING reference e Because these following operating instructions cover various models the characteristics of WARNING your vacuum cleaner may differ slightly from those described in this manual CAUTION WARNING SYMBOLS USED Indicates that a danger of death or serious injury exists WARNING Indicates that a risk of personal injury or material damage exists CAUTION OTHER SYMBOLS USED NX Represents something you must NOT do Represents something you must follow Indicates that you must disconnect the power plug from the socket e This vacuum cleaner is designed for domestic household use only WARNING Do not use this vacuum cleaner to clean building waste and debris Regularly keep the filters in clean conditions to prevent of collecting fine dust in them Do not use this vacuum cleaner with any of the filters removed Failure to meet these requirements could cause damage to the internal parts and void your warranty 02_ safety information safety information IMPORTANT SAFEG
4. UARDS GENERAL Read all instructions carefully Before switching on make sure that the voltage of your electricity supply is the same as that indicated on the rating plate on the bottom of the cleaner WARNING Do not use the vacuum cleaner when rug or floor is wet Do not use to suck up water Close supervision is necessary when any appliance is used by or near children Do not allow the vacuum cleaner to be used as a toy Do not allow the vacuum cleaner to run unattended at any time Use the vacuum cleaner only for its intended use as described in these instructions Do not use the vacuum cleaner without a dust bin Empty the dust bin before it is full in order to maintain the best efficiency Do not use the vacuum cleaner to pick up matches live ashes or cigarette butts Keep the vacuum cleaner away from stoves and other heat sources Heat can deform and discolour the plastic parts of the unit Avoid picking up hard sharp objects with the vacuum cleaner as they may damage the cleaner parts Do not stand on the hose assembly Do not put weight on the hose Do not block the suction or the exhaust port Switch the vacuum cleaner off on the body of the machine before unplugging from the electrical outlet Disconnect the plug from the electrical outlet before emptying the dust bin To avoid damage please remove the plug by grasping the plug itself not by pulling on the cord safety information _03 e This appliance
5. attery compartment cover pollutants such as dust may accumulate in the compartment and cause a problem Therefore be sure to use the product with the compartment cover closed e Take care when you use the cleaner because the dust sensor may malfunction or may break due to an impact Dust Sensor 2 EA Installing the Dust Sensor e Assemble the dust sensor between the air inlet connector and the extension pipe Recommended YANVATO AHL ONILVdAdO Z0 You can assemble the dust sensor between the extension pipe and the hose The assembly position of the dust sensor operating the cleaner _13 maintain tools anc iter USING ACCESSORY Pipe e Adjust the length of the telescopic pipe by sliding the length control button located in the center of the telescopic pipe back and forth e To check for blockages separate the telescopic pipe and adjust to shorten This allows for easier removal of waste clogging the tube Accessory e To use the crevice tool push the accessory on to the end of the hose handle in the opposite direction e Pull out the button to use the dusting brush e To use the upholstery tool push the accessory on to the end of the hose handle 14 maintain tools and filter Accessory e Push the accessory onto the end of the hose handle e Pull out the dusting brush to use the crevice tool e Push the accessory onto the end of the pipe e
6. can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without Supervision e Children should be supervised to ensure that they do not play with the appliance e The plug must be removed from the socket outlet before cleaning or maintaining the appliance e The use of an extension cord is not recommended e f your vacuum cleaner is not operating correctly switch off the power supply and consult an authorized service agent e lf the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard e Don t carry the vacuum cleaner by holding the hose Use the handle on the vacuum cleaner set e Unplug the cleaner when not in use Turn off the power switch before unplugging e Do not use to suck up water e Do not immerse in water for cleaning e The hose should be checked regularly and must not be used if damaged e The vacuum cleaner handle contains electrical connections the handle is not a serviceable part e The current carrying hose handle contains electrical connections is not a serviceable part by user e Please con
7. en Transparent Cover button inward to remove the cover 2 Use the crevice tool to remove impurities such as dust and hair from the brush roll 3 When done push the button outward to close the cover maintain tools and filter 19 DUST FULL INDICATOR Remote control type Body control type e Frequent vacuuming of hair or pet fur may cause a falling off of the rotation due to matters tangled around The lamp will turn red when suction is reduced If the light comes on please change the bag CHANGING THE DUST BAG You can purchase dust bags in the shops where you bought this vacuum cleaner or authorized SAMSUNG service center CLEANING INLET FILTER Don t throw away the filter 20_ maintain tools and filter CLEANING OUTLET FILTER NZ Sr P j e Please replace the filter 1 2 times a year e When suction is noticeably reduced continuously or vacuum cleaner abnormally overheats please clean the outlet filter Note Do not wash HEPA filter If cleaning does not resolve the problem Please replace blocked out filter e Replacement filters are available at your local Samsung distributor CHANGE THE BATTERY REMOTE CONTROL TYPE e When the vacuum cleaner does not work replace the batteries If the problem persists please contact our authorized dealer e Use 2 batteries of size AAA e Never disassemble or recharge the batteries CAUTION e Never heat u
8. er completely if the inlet is blocked Power Pet Plus Brush Option dala ANV STOOL NIVLNIVW 0 For improved pickup of pet hair and fibre on carpets e Frequent vacuuming of hair or pet fur may cause a falling off of the rotation due to matters tangled around Push the Open button of the transparent screen cover to separate the cover Remove the brushbar from the transparent screen Remove waste matter such as dust and hair tangled around the brushbar using scissors Remove dust inside the brush housing using a dry duster or crevice tool Insert brushbar into rotating belt and assemble Click the transparent screen cover back into place to reassemble ao eG Parquet Master Brush Option e Vacuum dust in wide area at once e Remove waste matter completely if the inlet is blocked maintain tools and filter _17 Mini turbo brush Option To replace brushroll 1 Ifa clog is present or debris is visible unscrew the two screws on the back of the Mini turbo brush to remove the faceplate and clear any obstructions 2 Inspect condition of brushroll Replace brushroll if brushes are worn down To remove brushroll pull up and out of end slots in nozzle housing Insert ends of brushroll into same slots to replace Inspect belt to ensure that it is in good condition If belt is broken or cracked replace belt according to To Replace Belt instructions 3 Using at MAX Press the MAX button to operate the
9. essed for 30 minutes while cleaning the safety device is activated and the power is cut off In this case press the Power button on the main unit or unplug and then plug the power cord in again YANVAT0 AHL ONILVdAdO Z0 HOSE SC21F60YG SCO8F60YW Series 1 ON OFF Button Co Press the ON OFF button to operate the vacuum cleaner ra Press again to stop the vacuum cleaner i 2 SUCTION Button Press the SUCTION button to increase or decrease the suction power Each time you press the button you gradually increase the suction power After the suction power reaches its maximum the next time you press the button you return the suction power to its minimum Handle Control The cleaner is controlled by radio f ignals ON MIN gt requency signals a B 3 BRUSH ON OFF Button Press the BRUSH ON OFF button to operate the UV Brush Press again to stop the UV Brush l1 gt x lll If no button is pressed for 30 minutes while cleaning the safety device is activated and the power is cut off In this case press the Power button on the main unit or unplug and then plug the power cord in again operating the cleaner _09 BODY Press the power ON OFF button repeatedly to start and to stop the vacuum cleaner OFF gt ON gt OFF If the remote handle control is not working the cleaner can be operated using the ON OFF button on the body of the machine 1 The icon lights up b
10. lue when the power source is connected 2 If the filter check indicator turns red check and eliminate possible blockages in brushes ee pipe hoses filters and if necessary Empty and replace dust bag Body control type SC21F60WA Series HOSE To reduce suction for leaning draperies small rugs and other light fabrics pull the tap air until the hole is open BODY To control power level just slide the power control right and left MIN For delicate fabrics e g net curtains MAX For hard floors and heavily soiled carpets If the filter check indicator turns red check and eliminate possible blockages in brushes pipe hoses filters and if necessary Empty and replace dust bag TE 10_ operating the cleaner USING THE UV BRUSH SC21F60YG SCO8F60YW SERIES 1 Insert the brush into the hose handle e Insert the UV brush securely into the hose handle until you hear a clicking sound 2 Press the BRUSH ON OFF button to use UV Brush e Press the Suction button to start cleaning and choose the appropriate suction strength e Press the BRUSH ON OFF button e UV sterilization cannot be activated by itself YANVATO AHL ONILVdAdO Z0 3 When you have finished UV cleaning press the 4 button e Press the 5 button to stop the cleaner For safety reasons UV brushing only runs for 30 minutes and then stops operating To resume the operation press the SUCTION
11. n W T50 750 Eco Label No No 1 Annual energy consumption is calculated based on 50 cleaning tasks per year 2 Actual annual energy consumption will depend on how the appliance is used a If you have any questions or comments relating to Samsung products please contact the SAMSUNG Customer care center COUNTRY CUSTOMER CARE CENTER WEB SITE U K 0330 SAMSUNG 7267864 www samsung com SOUTH AFRICA 0860 7267864 SAMSUNG www samsung com DJ68 00698D 02
12. p the batteries or throw them into fire e Do not reverse poles e Dispose of the batteries property BATTERY TYPE AAA Size maintain tools and filter _21 dala ANV STOOL NIVLNIVW 0 troubleshooting PROBLEM SOLUTION Motor does not start e Check cable pulg and socket e Leave to cool Suction force is gradually decreasing e Check for blockage and remove Cord does not rewind fully e Pull the cord out 2 3 m and push down the cord rewind button Vacuum cleaner does not pick up dirt e Check hose and replace if required Low or decreasing e Please check filter and if required clean as illustrated in the suction instructions if filters are out of condition change them to new ones Body overheating e Please check filters if required clean as illustrated in the instruction ro e Please decrease power suction Static electicity a i e This can also occur when air in the room is very dry discharge Please ventilate the room to air humidity become a normal This Vacuum cleaner is approved the following EMC Directive 2004 108 EEC Low Voltage Directive 2006 95 EC 22_ troubleshooting Product fiche English According to Comission Regulation EU No 665 2013 NS Supplier Samsung Electronics Co Ltd SCO8F60JNT SCO8F60YW General purpose vacuum cleaner Hardfloor Cleaning Performance Class ai Power Consumptio
13. rent characteristics of UV lamps Please keep the UV Brush indoors safety information _05 contents ASSEMBLING THE CLEANER OPERATING THE CLEANER MAINTAIN TOOLS AND FILTER 06_ contents TROUBLESHOOTING 08 08 09 11 12 Power cord ON OFF Switch Power control Using the UV brush Option Using the Dust Sensor Option Using accessory Cleaning the Dust Sensor Option Maintain floor tools Dust full indicator Changing the dust bag Cleaning inlet filter Cleaning outlet filter Change the battery remote control type assembling the cleaner e For storage park the floor nozzle OPTION assembling the cleaner _07 YANVAT10 AHL ONINIENASSV 10 operating tne cleaner POWER CORD e When removing the plug from the electrical outlet grasp the plug not the CAUTION cord ON OFF SWITCH 08_ operating the cleaner POWER CONTROL Remote control type SC21F60JD SC21F60YG SCO8F60JT SCO8FE0YW Series HOSE SC21F60JD SCO8F60UT Series 1 ON OFF Button Press the ON OFF button to operate the vacuum cleaner Press again to stop the vacuum cleaner 2 Suction Button Press the button to operate the vacuum to highsuction power Press the button to operate the vacuum to low suction power Handle Control ON MIN gt MAX The cleaner is controlled by radio u frequency signals TA If no button is pr
14. tact the manufacturer or service center for a replacement 04_ safety information UV BRUSH since the UV rays from the UV Brush damage skin and eyes never allow the rays to make contact with skin or eyes and do not let children or the elderly use the UV Brush It may damage your eyesight If the transparent window is broken and the UV rays are exposed directly turn the power off and contact the service center Do not use the UV Brush for purposes other than the sterilization of mattresses bedclothes beds cushions and so on made from material The company will not be held liable for any loss due to accidents from using the UV Brush for purposes other than its original purpose as listed above Do not sit on the UV Brush or drop it and avoid imparting impacts on the product Failing to do so may result in injury or product damage Do not touch the power terminals on the back of the UV Brush with a metal pin or rod This may result in electric shock or fire When the UV lamp is out of order never disassemble or modify the product yourself Please contact the manufacturer or service center for a replacement since an internal discharge occurs within the UV Brush never use the product near an inflammable spray or substance Take care not to touch the UV lamp window after using the UV Brush for an extended period of time as the surface of the window may be hot The UV Brush may start slowly at a low temperature due to the inhe
15. vacuum at maximum intake To replace belt 1 Remove bottom plate See figure in To Replace Brushroll instructions 2 Loop one end of new belt around shaft of pulley 3 Loop other end of belt around designated area for it on brushroll Insert brushroll into slots in nozzle housing See figure in To Replace Brushroll instructions 4 Fit Mini turbo brush back together as described in To Replace Brushroll instructions 18 maintain tools and filter To remove dust from the dust bin of the UV brush SC21F60YG SCO8F60YW Series When you notice that the dust bin is filled use the Dust Removal button to empty the dust bin 1 To remove dust from the dust bin move the Dust Removal button to the Open position While the cleaner is operating Suction use the Dust Removal button for this purpose 2 When done move the Dust Removal button to the Close position When the Dust Removal button is in the Open position the suction power of the cleaner is reduced e Frequent vacuuming of hair or pet fur may cause a falling off of the rotation due to matters tangled around dala ANV STOOL NIVLNIVW 0 Cleaning the UV brush Cleaning the drum SC21F60YG SCO8F60YW Series You should check your vacuum cleaner s Brush roll regularly Strings hair and carpet fibers can wrap around the brush and hamper its ability to clean To prevent this you should clean the brush 1 Push the Op
Download Pdf Manuals
Related Search