User Guide 0-15Kg (0-4 yrs)
Contents
1. dry units can have an adverse effect on manoeuvrability and steering 1407 001 VISIO AX118 User Guide indd 2 3 When using the Stroller on the beach clean it completely afterwards to remove all the sand and salt from the mechanisms and wheel assemblies lf there are compression marks or indentations on the tyres use a domestic hair dryer to gently warm the area This should help make them disappear DO NOT OVERHEAT Under certain climate conditions the covers and trims may be affected by mould and mildew To help prevent this occurring do not fold or store this Stroller if it is wet or damp Always store in a well ventilated area To maintain the safety of your Stroller seek prompt repairs for bent torn or broken parts Use only those parts and accessories approved by Britax Replacement parts and accessories are available from your Britax stockist or contact Britax Customer Service Department on 01264 386034 This product is not intended for commercial use WARNING Use a harness as soon as your child can sit unaided WARNING Any load attached to the handle affects the stability of the pushchair WARNING This vehicle is only intended for children from birth and up to 15kg WARNING This vehicle is not suitable for running or skating WARNING It may be dangerous to leave your child unattended WARNING Ensure that all locking devices are fully engaged before use WARNING Use a harness as s2. To lock the front swivel wheels into the locked position align front wheels into a straight forward position and slide the wheel lock guide up dia 9a To unlock the front wheels slide front wheel lock guide down dia 9b Lower the backrest into the infant carrier position lowest position dia 12c by squeezing and pulling the adjustment handle upwards dia 12d To use the pushchair brake IMPORTANT Parking brake is to be used only when pushchair is stopped DO NOT apply the parking brake to a moving pushchair IMPORTANT To prevent the pushchair from moving always use the parking brake when loading unloading pushchair or making any adjustments To lock rear wheels for parking or loading pushchair depress foot brake dia 10a To release brake simply lift up the foot brake to disengage brake from rear wheel hubs dia 10b IMPORTANT Always use the brake pedal as using the connecting bar will cause it to bend For your childs comfort unfasten the harness and move them away to the side of the pushchair dia 12e Insert the optional infant comfort pad or mattress in the position shown dia 12f The magnets will hold the infant comfort pad in position The D rings can be used to attach your own harness Place the hood in the correct position with the window at front of pushchair over the pushchair Attach the hood clip to each side of the pushchair frame by locating the clips over the top of the up
3. User Guide 0 15Kg 0 4 yrs 1407 001 VISIO AX118 User Guide indd 1 22 6 07 15 22 47 C ce Important Children up to 15kg approx 4 years Warnings amp Guarantee WARNING A CHILD S SAFETY IS YOUR RESPONSIBILITY Read these instructions carefully before use and keep them for future reference Your childs safety may be affected if you do not follow these instructions Please read this User Guide carefully BEFORE trying to use your pushchair Looking after your pushchair The pushchair and its cover have been carefully designed manufactured and tested to high safety standards Regularly inspect and maintain your pushchair to ensure freedom of movement of the joints locking devices and security of components To prolong the life of your pushchair keep it clean and do not leave it in direct sunlight for extended periods of time Cleaning the cover The seat cover is removable and can be washed in accordance with the washing instructions on the label The hood and trims may be cleaned using warm water with household soap or mild detergent Allow it to dry fully preferably away from direct sunlight DO NOT dry clean or use bleach or any other aggressive cleaning agents IMPORTANT MAINTENANCE ADVICE If the wheels squeak use a silicon based spray or light lubricating oil ensuring it penetrates the wheel and axle assembly Regularly clean and lubricate the front swivel and wheel units as dirty or
4. cushion remove them 22 6 07 15 22 57 5 Using your pushchair for carrying a toddler Children up to 15kg approx 4 years 5 Using your pushchair for carrying a toddler continued Children up to 15kg approx 4 years Lower the leg support into the toddler carrying position dia 14a and 14b Note The bumper bar may need to be removed during this procedure Raise the backrest into the toddler carrying position upright position dia 14c by squeezing and pulling the adjustment handle upwards Unfasten the harness and insert the optional infant comfort pad in the position shown rethread the harness through the slots in the infant pad dia 14e and 14f To secure your child A five point harness is provided to restrain your child dia 14g To secure the child in the harness push buckle Q through and into until the buckle prongs snap into position Carefully adjust the harness by pulling the slider until the desired fit is achieved in the waist belt shoulder and crotch straps Always adjust the harness when changing the seating position of the child To release the buckle squeeze the top and bottom prongs WARNING Always use the crotch strap in combination with the waist belt WARNING Fasten the harness when not in use to prevent it becoming trapped when folding the pushchair D rings are provided at each side of the seat for attachment of an alternative harness 1407 001 VISIO AX118 U
5. e sides Thread the front press stud straps through the metal loops attached to the front of the frame press studs together dia 4a Thread the rear press stud straps around the rear legs and above the frame press studs together dia 4b Extending and retracting the handles To extend each of the pushchair handles press the button located at the top of each handle inwards dia 5a pull the handles towards you to extend dia 5b Threading the underside chassis cover straps Place the pushchair on it s side to gain better access to the underside cover straps Thread the loose end of the strap through both D rings dia 6a Thread the strap back over the last D ring and back through the first D ring dia 6b Pull the strap tight Adjusting the backrest Squeeze clips towards each other to release the backrest lock dia 7a Move the backrest into the desired position dia 7b To adjust the calf support Lower the calf support by lifting up the release latches located underneath both sides of the calf support dia 8a and push the calf support down Raise the calf support by lifting it until the release latches lock into place dia 8b 22 6 07 15 22 53 Using the front swivel wheel locks Open the bumper bar see dia 3a and 3b Raise the calf support to the upright position dia 12a and 12b Close the bumper bar on the outside with the calf support on the inside
6. hchair in a safe place when not in use Avoid placing heavy objects on top of it and do not store near direct heat sources e g radiators open bar fires or in direct sun light as the cover may fade This pushchair is designed and manufactured to comply to EN1888 2005 This pushchair is a Type A chassis and is compatible with other Britax Type A products Guarantee All Britax products are carefully designed manufactured and tested However should this product prove faulty within six months of purchase due to a materials or manufacturing fault please return it to the original place of purchase We will then at our discretion repair it free of charge For guarantee purposes proof of purchase will be required We recommend that you retain your receipt and attach it to this user guide They should be kept in a safe place Britax does not accept liability for damage arising from abuse misuse or negligence This guarantee is not transferable and therefore does not apply to second hand products Your statutory rights are not affected by this guarantee 22 6 07 15 22 47 Introducing your new pushchair Children up to 15kg approx 4 years Infant Carrier Toddler Carrier 01 Extendable Handles 02 Frame Lock Release latches 03 Infant Comfort Pad optional 04 Seat Cover 05 Lower Framework 06 Foot Lock 07 Foot Brake 12 Harness straps 13 Arm Rest 14 Bumper Bar 15 Calf Supp
7. oon as your child can sit unaided WARNING Overloading incorrect folding and the use of non approved accessories may damage or break this pushchair and make it unstable for use WARNING Regularly inspect the pushchair to ensure all parts are in full working order DO NOT Do not add an additional mattress thicker than 15 mm in place of the infant comfort pad when used in infant carrier mode DO NOT allow the pushchair to remain wet for prolonged periods of time If it does get wet allow to dry unfolded at room temperature DO NOT carry more than 2kg in the shopping basket DO NOT allow children to play with or adjust the pushchair DO NOT carry more than one child on this pushchair DO NOT overload the pocket on the back of the hood this may cause the pushchair to fall backwards DO support the back of the pushchair seat when reclining it DO use a correctly fitted and adjusted harness at all times If using an alternative harness conforming to BS6684 D ring attachments are found on each side of the pushchair DO read the labels on the covers for washing instructions and do not tumble dry drip dry only DO regularly inspect the pushchair to ensure all parts are in full working order DO ensure children are clear of moving parts and locking devices while making adjustments DO periodically check that any screws nuts bolts and other fastenings are fully tightened DO store the pus
8. ort 16 Calf Support release latches 17 Foot rest 18 Front swivel wheel lock 19 D Rings 08 Hood 09 Hood Tensioner 20 Frame locking latch 21 Hood catch 22 Shopping Basket 23 Folding Handle 10 Removable Apron Panel 11 Removable Apron 1407 001 VISIO AX118 User Guide indd 4 5 22 6 07 15 22 49 1407 001 VISIO AX118 User Guide indd 6 7 Fitting and removal of the front swivel wheels Take each of the front swivel wheel assemblies and press them down onto each of the front legs You will hear a click when they are locked into place dia 1a If you need to remove a front swivel wheel press the wheel release lever dia 1b located on the underside of the wheel and lift the wheel assembly from the front leg Unfolding the pushchair Holding the pushchair in a vertical position lift up on the lock release latches dia 2a Push down on the foot lock with your foot whilst pulling both handles up firmly opening the pushchair until the chassis locks into the open position dia 2b Ensure the frame locking latch has locked on both sides Fitting the bumper bar Whilst pressing the button on the bottom of the bumper bar slide one side of the bar into the armrest socket in the position shown dia 3a release the button to engage the lock dia 3b Repeat this sequence for the other side Attaching the shopping basket Ensure the basket is fitted with the zips at th
9. per tube first then pushing until they click into place dia 12g Open the hood by pulling the front of the canopy forwards engaging the hood tensioners on each side to click in place dia 12h Folding your pushchair Lock the front wheels Position the seat in the front facing full upright position Lift up on the lock release latches dia 11a Lift up the lower framework with your foot then pull up on the folding handle to fold the frame dia 11b Hold pushchair vertically and push down on the handles until the latches lock on both sides you will hear a click dia 11c 1407 001 VISIO AX118 User Guide indd 8 9 22 6 07 15 22 56 3 Using your pushchair as an infant pram continued Children up to 9kg or until your child can sit unaided 4 Using your pushchair with an infant carrier Children up to 13kg approx 1 year 1407 001 VISIO AX118 User Guide indd 10 11 Place the optional apron over the frame as shown dia 12i On each side fold the hook and loop strap back onto itself and tuck inside the apron Attach the remaining hook fastenings on both sides of the apron to the loop fastenings on each side of the seat cover dia 12j The loop fastenings on the seat cover should be shared by the hook fastenings on both the apron and canopy Ensure that the left hand and right hand adaptors are used on the correct side of the child seat To fit the adaptor to the child seat
10. ser Guide indd 12 13 Place the hood in the correct position with window at rear of pushchair over the pushchair Attach the hood clip to each side of the pushchair frame by locating the clips over the top of the upper tube first then pushing until they click into place dia 14h Open the hood by pulling the front of the canopy forwards engaging the hood tensioners on each side to lock it in place dia 14i Attach the optional apron in the toddler position place the apron over the frame as shown dia 14j Attach the hook and loop straps on each side around the pushchair chassis threading straps between the tubes as shown dia 14k 22 6 07 15 22 59 6 Removing and refitting the covers and harness 6 Removing and refitting the covers and harness continued Children up to 15kg approx 4 years Children up to 15kg approx 4 years Unfolding the armrest pads A To remove the infant pad x Unthread the harness if it s in the toddler carrying position dia 15f To unfold the armrest pads pull down on the fabric on the outer side and fold into the centre of the pushchair dia 15a To refit the infant pad simply place the infant pad in the pushchair thread the harness back though then use the magnets to keep it in place To remove the optional removable apron Removing the bumper bar cover To remove the bumper bar cover simply unzip the bumper bar cover and remove from the plastic mo
11. squeeze the lever and insert into the space below the handle dia 13a Make sure it is fully fitted and release the lever to lock into place Repeat this process for both adaptors Fitting the infant carrier First unfold the armrest covers please see dia 15a Lower the infant carrier will be labelled Type V A B W onto the armrests in the orientation shown dia 13b making sure that the prongs either side drop into both slots on each armrest Push down firmly Once the infant carrier is engaged you will hear a click Lower the infant carrier handle to the safety stop position Please refer to the user guide for the infant carrier WARNING Check that the attachment devices are correctly engaged before use Removing the adaptors Removing the infant carrier To remove the infant carrier move the handle to the carrying position Please refer to the user guide for the infant carrier Pull up the release levers on each side dia 13d and lift the infant carrier out of the sockets dia 13e The infant carrier is now ready for use Re attach the armrest pads after use To remove the adaptors from the child seat pull the lever on the adaptors away from the child seat while pulling down dia 13f Repeat the process for both adaptors IMPORTANT It may be necessary to remove the adaptors from the child seat when installing it in your vehicle If the adaptors are in contact with the vehicle seat
12. ulding dia 15b Unfasten the hook loops on both sides of the seat dia 15g then pull the apron off dia 15h Removing the shopping basket Remove the press studs straps located at the rear dia 15c and the front dia 15d of the shopping basket Removing the canopy hood Pull the hood clips off the bars located just above the armrest dia 15e 1407 001 VISIO AX118 User Guide indd 14 15 Removing the main chassis cover Unthread the underside cover straps dia 15j Unhook the cover from under the calf support by pulling up in the direction shown dia 15k The chassis cover can now be lifted from the pushchair frame dia 151 and m and the harness released from the chassis cover To refit all the covers simply reverse the above instructions 22 6 07 15 23 02 Britax Excelsior Limited 1 Churchill Way West Andover Hampshire SP10 3UW United Kingdom Tel 01264 386034 www britax eu Britax is a registered trademark of Britax Childcare AZ0 048 1407 001 VISIO AX118 User Guide indd 16 22 6 07 15 23 02
Download Pdf Manuals
Related Search