UN2011 Installation Manual
Contents
1. 1 2 2 Mains power connection When connecting the mains plug to a suitable power cord ensure that mains Live is connected to the terminal marked L mains Neutral is connected to the terminal marked N and that mains Earth is connected to the terminal marked GND or sw 1 2 3 ARCNET interface A NC2011 network card is fitted as standard to provide for interfacing to a two wire RS485 FP2000 ARCNET Network Using network extension modules NE2011 NE2051 the unit can be configured to provide for conversion between optical and RS485 mediums as well as implementation of a wide range of topologies For details regarding ARCNET network topologies refer to the FP2000 Network Configuration Guide 1 2 4 Interface to external RS232 systems Connections to external systems are made by means of a RS232 cable supplied with the Universal Node Two RS232 ports are provided These are referred to as SER1 and SER2 A modem not supplied is required if the UN2011 is to be interfaced to a telephone line The modem MOD2000 is to be ordered separately and is to be installed by the User Space is provided inside the Universal Node to fit the Modem 1 2 5 Configuring the Universal Node The Universal Node is provided with default configuration settings for both serial ports SER1 and SER2 Only SER2 settings can be changed if required UN2011 Universal Node Installation Manual 5 2 INSTALLATION 2 1 Precautions The Universal Node is2. Optical fibre Figure 1 UN2011 Universal Node 1 2 O 0 0 O O I o 5 DO lo c lt 4 7 25 o Um DM 13 IO esa OJ lt 5 ETT in 14 6 O O 15 16 1 Strapto hold battery in place 9 Mounting holes 4 5 mm diameter 2 Battery not included 12V 1 2Ah 10 Modem MOD2000 Optional 3 Host CPU card FC2011 11 Serial port SER1 4 Network Card NC2011 NC2051 12 Serial port SER2 5 Power supply PS1200U 13 Modem power connection 6 Mains plug with fuse 14 Fault relay 7 Transformer 15 Memory lock and service switches 8 Battery terminals Note When 16 Start up switch connecting battery observe correct polarity 4 UN2011 Universal Node Installation Manual 1 2 1 Power supply The UN2011 Universal Node is powered from mains Provision is made for charging an internal battery not supplied to serve as a standby power supply if mains power fails Space is provided to mount the battery inside the unit The power supply is fitted with a connection to supply power to a modem MOD2000 A fault relay is supplied on the power supply board This relay can be used to remotely indicate a faulty power supply mains failure battery not connected under voltage etc
3. Ctrl S 20 Fire Brigade Delay Ctrl T 21 Reserved Ctrl U 22 Fire Brigade Stop Ctrl V 23 Reserved Ctrl W 24 Reserved Ctrl X 25 Reserved Ctrl Y 26 Up Arrow Ctrl Z 27 Exit Ctrl 28 Reserved Ctrl 29 Panel Ctrl 30 All Ctrl 4 31 Fire Brigade signal Ctrl _ UN2011 Universal Node Installation Manual 13 14 UN2011 Universal Node Installation Manual UN2011 Universal Node Installation Manual 15 CE 1050261
4. Node ID SYSTEM CONFIGURATION ID Format 0 R or P O R Repeater P Panel For the Universal Node the following option is available un m 0 0 Change this into the Ne ID of the PC acting as a global repeater Example PC Own Node ID 2 gt un m 2 Assign the serial port SER2 to be a modem port SYSTEM CONFIGURATION COMMUNICATION PORT SETUP SER 2 MODEM 3 Complete your modem set up SYSTEM CONFIGURATION COMMUNICATION MODEM The following parameters must be configured Wait for connection Pause between dials Max dialling attempts nit string for example ATL1E1 amp FOM1 NO J0 Q3 amp Q0 amp W0S0 2 Dial command Escape Hang up Test ID oe is the identification string of the site This string is being used to locate the events Note that these settings can be configured depending on modem type using the Modem function in the SYSTEM SET DEFAULT menu UN2011 Universal Node Installation Manual 11 4 TECHNICAL SPECIFICATIONS Mechanical DIMENSIONS adi iaia aloe ont leto let ea et he ic ia 65 x 400 x 300 mm Weight without batteries iiine eaa aeei aa ao ei Te rue a eaae de ERR DUE ue e e eee aueh 5 Kg Electrical Power Supply He dacia ti dere etici olaa drid 230 VAC 50 Hz 10 VA Weight without batteries t meet e teil ie idt a andes 5 kg IM E 160 mA 250V T uc 1 2 Ah 12V Fault relay maximum switching current eene 2A 24 VDC Fault relay maximu
5. intended for installation by qualified and trained personnel Ensure that the correct procedures are followed when installing the equipment Ensure that the input voltage of the equipment corresponds with that of the power outlet before connecting it to mains power Always disconnect unit from Mains power before opening it Close the unit before connecting power Shock hazards may exist if the Universal Node is not properly grounded Ensure that the lid of the Universal Node is in the closed position and that the two screws provided for fixing the lid in position are properly tightened Any modification maintenance or repair are permitted only by authorised personnel To ensure safe operation and to keep the product safe pay heed to the information cautions and warnings in this manual Failure to do so will violate the safety standards of design manufacture and intended use of the equipment 2 2 Installation The following procedure is to be followed for installing a Universal Node assuming that the ARCNET network design is completed 2 2 1 Configuring and connecting the ARCNET card to the FP2000 network 1 Ensure that mains power is disconnected from the Universal node before opening it disconnect the battery 2 Ensure that the default configuration of the ARCNET Network meets the requirement node ID operational mode data rate topology 3 Configure and connect the ARCNET Card NC2011 as follows bus to
6. DB9 UN2011 female to DB9 PC side female connection 1 DCD 1 DCD 2 RXD 2 RXD 3 TXD 3 TXD 4 DTR 4 DTR 5 GND 5 GND 6 DSR 6 DSR 7 RTS 7 RTS 8 CTS 8 CTS 9 RI 9 RI Figure 5 DB9 UN2011 female to DB25 PC side female connection DCD Q 1 RXD TXD DTR GND DSR RTS CTS RI 0 DCNDIRIA WAN 2 2 5 Connecting the modem The following procedure describes the installation of the MOD2000 modem The MOD2000 modem not supplied is provided with a bracket for wall mounting For installing this bracket into the Universal Node see Figure 1 1 Remove the protective cover from the double sided self adhesive tape on the rear mounting surface of the bracket supplied with the modem 2 Position the mounting bracket inside the Universal Node and fix in position using the double sided self adhesive tape 8 UN2011 Universal Node Installation Manual 3 Before connecting the Modem to the Universal Node ensure that the battery and the mains power is isolated 4 Carefully study the Modem User s Manual For connecting the Modem to the Universal Node and Telephone Line see Figure 6 5 Connect the Earth wire leading from the modem to the Earth stud inside the Universal Node The modem and associated circuitry is only protected if this connection is made 6 Connect the power harness leading from the modem to the power supply Observe correct polarity The connector leading to the printer is not used and should be tied dow
7. GE Interlogix ARITECH UN2011 Universal Node Installation Manual Version 4 5 June 2004 ARCNET is a registered trademark of Datapoint Corporation Aritech is a GE Interlogix brand http www geindustrial com ge interlogix emea 2004 GE Interlogix B V All rights reserved GE Interlogix B V grants the right to reprint this manual for internal use only GE Interlogix B V reserves the right to change information without notice UN2011 Universal Node Installation Manual CONTENTS 1 Introduction one alal iaia 4 Til Package contents s ui Lue A ee eee e 4 12 Description xL 4 2 Installation ELE 6 ZN Precautions arniran edite ale ine dl aa 6 2 2 Installation n tente tinte ea a aa eic og 6 3 Software Configuration ii nici 10 Si Default settings Iii te eee eo ette arr 10 3 2 Changing default settings iuii ei 10 3 9 Modeni settings nee e ea Ra o ERU de Ee d rd deu Eua uet one d eed eden 11 4 Technical Specifications 12 5 Appendix Emulation Control KeYySs iii 13 UN2011 Universal Node Installation Manual 3 1 INTRODUCTION 1 1 Package contents UN2011 Universal Node Mains cable plug RS232 cable 1 2 Description The Universal Node provides an access point for external systems to the FP2000 ARCNET network It links the FP2000 serial communication format implemented via RS232 and the FP2000 ARCNET protocol implemented via RS485
8. m power rating nnne nnne nnne nennen nnns 50 WDC Environmental Working temhperature enile cdita piie diede ebd et p did dd ca ede enden 0 C to 40 C Storage temperature Leere ett ee el eate t a deed d sell av nde 30 C to 65 C Relative humidity seo ro A lai 80 maximum without condensation Data communications Serial POS a einaudi tttm Lo Eo o ES 2 ARCNET O A a ii as 1 RS232 protocol defallt lui her e eerte leale ach neal See table RS485 protocol default cuicos Ri ale Rp ee Da ee pee ee aaa e ii See table RS232 protocol default RS485 protocol default 8 data bits 156 Kbps 1 stop bit Bus topology No parity On options refer to FP2000 Reference Guide 9600 bits per second DTE equipment On options refer to FP2000 Reference Guide 12 UN2011 Universal Node Installation Manual 5 APPENDIX EMULATION CONTROL KEYS No Description Keyboard key 0 Reserved Ctrl 1 Scroll Ctrl A 2 Display Alarm Ctrl B 3 Reserved Ctrl C 4 Print Screen Ctrl D 5 Alpha Numeric Ctrl E 6 Right Arrow Ctrl F 7 Reserved Ctrl G 8 Left Arrow Ctrl H 9 Silence Buzzer Ctrl l 10 Down Arrow Ctrl J 11 Reset Ctrl K 12 Disable Ctrl L 13 Enter Ctrl M 14 Test Ctrl N 15 Sound Sounder Ctrl O 16 Sounder Delay Ctrl P 17 Sounder Disable Ctrl Q 18 Silence Sounder Ctrl R 19 Fire Brigade Disable
9. n using mounting studs provided inside the Universal node 7 Connect the RS232 input on the modem to serial port SER2 8 Connect the telephone line to the modem protection board use the adapter supplied if required 9 Slide the modem into the bracket inside the panel and fix all cables in position using the hardware supplied Ensure that the modem cannot slide out of the bracket if the Universal Node is turned upside down 10 Restore battery and mains power to the Universal Node and turn the power switch and the modem on 11 Configure the serial port SER2 see section 3 2 Figure 6 Modem MOD2000 Interconnection Diagram 1 5V to printer not used Fix in position 5 Line to prevent contact 6 To SER2 2 To 5V power supply 7 Modem 3 Totelephone line adapter may be 8 Line required 4 Phone not used UN2011 Universal Node Installation Manual 9 3 SOFTWARE CONFIGURATION 3 1 Default settings UN2011 Default configuration settings Network node address 0 5 Note every node on the network must have a unique address Network operational mode 15 15 Note the operational mode must be the same for all items connected to the network Serial port SER1 Emulation Mode this allows for connecting to the serial port of a PC to change default settings Serial port SER2 Set up mode this allows for direct connection to a PC to enable upload or download of data FP Config applicati
10. on software as well as emulation maintenance manager application software SER1 and SER2 protocol Baud rate 9600 8 data bits 1 stop bit No parity DTE Equipment ARCNET port Data rate 156 Kbps Bus 3 2 Changing default settings Changing the default setting of serial port SER1 on the Universal Node is not possible The following procedure is recommended to change the default configuration settings of the Universal Node 1 Before you attempt to change the software default settings ensure that you have Windows 95 or later and that you have access to Hyper Terminal Copyright 1995 Hilgraeve Inc or similar application software 2 Connect SERI of the Universal Node to the COM1 COM2 or COM3 port 3 Configure COM1 COM2 or COM3 port using Hyper Terminal to the following Baud rate 9600 8 data bits 1 stop bit No parity DTE Equipment 10 UN2011 Universal Node Installation Manual 4 Using Hyper Terminal connect the relevant COM1 COM2 or COM3 port to the Universal Node 5 Configure the Universal Node as required using the Emulation Control keys as detailed in section 5 Appendix Emulation Control Keys For detail on menus and how to navigate through them refer to the FP2000 reference Guide 3 3 Modem settings 3 3 1 Modem Settings at the Universal Node The following procedure is to be followed to configure serial port SER2 for a modem application 1 Give the Universal Node a
11. pology only Remove the Jumper J1 on the ARCNET card select Bus Topology mode Determine if the Universal Node is positioned at an end of line position If it is then the RS485 Line must be terminated with an end of line resistor equal to the characteristic impedance of the cable Insert jumper J1 next to the RS485 connections on the network extension card This terminates into a resistance of 120 O Resistance can be added if the cable characteristic impedance is not 1200 Ensure that the screen of the RS485 cable is continued between nodes and that itis grounded at one point only This can be done through inserting a jumper J2 on the network card Connect the RS485 wires For more information on topologies network cards network extension cards as well as wiring refer to the Network Configuration Guide 6 UN2011 Universal Node Installation Manual Figure 2 RS485 network card connections NC2011 2 3 4 O 1 A O 1 Repeater mode selection 3 Channel A 2 Jumper termination end of line J1 4 Jumper Earth connection J2 2 2 2 Installation of a battery 1 Ensure that mains power is disconnected before opening the unit 2 Ensure that the battery selected complies with specification see Section 4 Technical Specifications 3 Remove the protective cover from the double sided self adhesive tape and position the battery as shown in Figure 1 Fix it in position with the strap provided Ensure tha
12. t the strap is sufficiently tightened to prevent it from coming lose 4 Connect the battery as shown Observe correct polarity Incorrect polarity can seriously damage the unit 2 2 3 Connecting the power supply and fault relay 1 Ensure that the mains power is disconnected before opening the unit 2 Connect the fault relay as shown in Figure 3 3 Route the wires away from sharp edges and corners and fix in position Figure 3 Fault relay connections 680 N The relay is shown in the fault condition 2 2 4 Connecting the RS232 external system 1 Ensure that the Universal Node is disconnected from mains power before opening it 2 Ensure that the default configuration of the Serial Port SER2 as detailed in section 3 1 Default settings meets that of the External RS232 System If not see section 3 2 Changing default settings UN2011 Universal Node Installation Manual 7 Check the RS232 cable 4 Connectthe RS232 cable to the serial port SER2 on the CPU card as well as to the RS232 port of the External System 5 Configure the RS232 system Unique Node Identification RS232 protocol parameters 6 Connect mains to the Universal Node and start the external RS232 system The RS232 serial connection is via a 9 Pin D type male connector See Figure 4 DB9 UN2011 female to DB9 PC side female connection and Figure 5 DB9 UN2011 female to DB25 PC side female connection for pin out connections Figure 4
Download Pdf Manuals
Related Search